Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Here are some Asus VivoBook 15 F512 X512 design highlights: HP Spectre x360 13t-ae000
– The laptop can support two storage drives: 2.5″ SATA drive and M.2 SATA SSD. disassembly
– There is only one RAM slot available for upgrades. Replacing touchscreen on
– The cooling fan easily removable. Dell Inspiron 11 3147 3148
– The DC power jack soldered to the motherboard. HP Spectre x360 15-ch
– The keyboard permanently attached to the top case. series Convertible PC
disassembly
For this disassembly you will need only three basic tools: Phillips #1 screwdriver, case
How to disassemble Asus
opener tool and tweezers. If you are interested, here’s my laptop repair tool collection.
VivoBook 15 F512 X512
Replace screen on Dell
Removing the base cover Inspiron 5568 5578 5579
7569 7579
STEP 1.
Replace screen on Dell
Remove ten screws securing the base cover. There are three types of screws: orange – the
Inspiron 7347 7348 7352
longest screw, red – medium length screws, green – short screws.
7353 7359
Replacing LCD screen on Dell
STEP 2.
Inspiron 15 5565 5567
Pry up the base cover and start separating it from the top case assembly.
STEP 3.
Select brand
Continue removing the base cover with your hands. You’ll have to apply some reasonable
1. Acer
force to remove the cover. There are multiple hidden latches attaching it to the top case.
2. Asus
STEP 4. 4. Dell
Remove four screws securing the battery and the battery mounting bracket. Remove the
5. Gateway
bracket.
Miscellaneous Tips
STEP 6.
Unlock the battery cable connector and disconnect the battery cable from the motherboard.
Slide the metal clip to the shown direction (yellow arrow). This clip covers the battery cable
to secure the connection.
Now you can lift up the battery cable and unplug it from the motherboard. Do not use metal
tools to lift up the connector. You can accidentally short the pins and damage the battery or
the motherboard. Use your fingernails instead.
STEP 7.
The speaker cables and the Wi-Fi antenna cables are routed in the guided path on the side
of the battery. Separate all cables from the battery.
STEP 8.
Lift up the battery and remove it from the top case. The battery hinges on two knobs on the
left side. Make sure to put it back in place properly during the re-assembly process.
STEP 9.
Remove the memory module and replace it with a larger capacity module if necessary.
STEP 10.
Remove one screw securing the M.2 SATA SSD and pull the SSD out. This is type 2280 M.2
SSD.
STEP 11.
Disconnect the 2.5″ SATA hard drive cable from the motherboard.
STEP 12.
Remove the 2.5″ hard drive from the laptop.
This is a regular 1TB 2.5″ spinning SATA hard drive. I would strongly recommend replacing it
with a 2.5″ solid state drive which is much faster. When you upgrade the hard drive, you’ll
have to transfer the SATA cable and the rubber sleeve to the new drive.
STEP 14.
Lift up and remove the cooling fan.
Lift up and remove the padding foam which has an adhesive tape on the bottom.
Peel off the clear tape and unplug the display video cable from the motherboard.
STEP 16.
Open the display panel 90 degrees and place the laptop upside down on the edge of your
desk.
Remove four screws securing the display hinges.
STEP 17.
Now you can separate the display panel from the top case assembly and remove it.
I don’t show how to remove the LCD screen in this guide but it shouldn’t be difficult. I
believe the screen removal procedure is pretty much standard:
1. Remove two screws from the lower left and right corners of the display assembly.
2. Remove the screen bezel.
3. Remove all screws securing the screen.
4. Disconnect the display cable from the back of the screen.
STEP 19.
Lift up and remove the USB board.
STEP 20.
Remove all screws securing the motherboard and disconnect the following color-coded
cables:
– Speaker cable (yellow).
– Touchpad cable (green).
– Keyboard cable (blue).
– Keyboard backlight cable (pink).
Also, its necessary to remove the Wi-Fi card.
Now you can separate the motherboard from the top case and remove it.
The DC-IN power jack soldered to the motherboard. If it fails, you’ll have to unsolder the
failed DC jack and replace it with a new one.
Removing the touchpad
STEP 21.
Remove one screw securing the touchpad and disconnect two cables. Remove the touchpad.
The keyboard is not removable because it’s permanently attached (riveted) to the top case.
If the keyboard fails, you’ll have to replace the entire top case assembly.
2 Responses
Hello, I have taken this partially apart and did not find the cmos battery. Could u
tell me where it is located or point me in the right direction for jump pins to short
it out? I am desperately needing to reset the bios admin password. I bought this
and it has been refurbished, Magic Simba did not reset the password before it
was sent to me. Thanks so much.
It looks like the motherboard doesn’t have the CMOS battery. Sorry, I
don’t know how to clear the password.
Leave a Reply
Your email address will not be published. Required fields are marked *
Comment
Name * Email *
Notify me of followup comments via e-mail. You can also subscribe without commenting.
Post Comment