Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
LED TV
SERVICE MANUAL
CHASSIS : LD55C
CONTENTS ............................................................................................... 2
SPECIFICATION ....................................................................................... 6
DISASSEMBLY ....................................................................................... 16
Copyright © LG Electronics. Inc. All rights reserved. -2- LGE Internal Use Only
Only for training and service purposes
SAFETY PRECAUTIONS
Copyright © LG Electronics. Inc. All rights reserved. -3- LGE Internal Use Only
Only for training and service purposes
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service 2. After removing an electrical assembly equipped with ES
manual and its supplements and addenda, read and follow the devices, place the assembly on a conductive surface such as
SAFETY PRECAUTIONS on page 3 of this publication. aluminum foil, to prevent electrostatic charge buildup or expo-
NOTE: If unforeseen circumstances create conflict between the sure of the assembly.
following servicing precautions and any of the safety precautions 3. Use only a grounded-tip soldering iron to solder or unsolder
on page 3 of this publication, always follow the safety precau- ES devices.
tions. Remember: Safety First. 4. Use only an anti-static type solder removal device. Some sol-
der removal devices not classified as “anti-static” can generate
General Servicing Precautions electrical charges sufficient to damage ES devices.
1. Always unplug the receiver AC power cord from the AC power 5. Do not use freon-propelled chemicals. These can generate
source before; electrical charges sufficient to damage ES devices.
a. Removing or reinstalling any component, circuit board 6. Do not remove a replacement ES device from its protective
module or any other receiver assembly. package until immediately before you are ready to install it.
b. Disconnecting or reconnecting any receiver electrical plug (Most replacement ES devices are packaged with leads elec-
or other electrical connection. trically shorted together by conductive foam, aluminum foil or
c. Connecting a test substitute in parallel with an electrolytic comparable conductive material).
capacitor in the receiver. 7. Immediately before removing the protective material from the
CAUTION: A wrong part substitution or incorrect polarity leads of a replacement ES device, touch the protective mate-
installation of electrolytic capacitors may result in an explo- rial to the chassis or circuit assembly into which the device will
sion hazard. be installed.
2. Test high voltage only by measuring it with an appropriate CAUTION: Be sure no power is applied to the chassis or cir-
high voltage meter or other voltage measuring device (DVM, cuit, and observe all other safety precautions.
FETVOM, etc) equipped with a suitable high voltage probe. 8. Minimize bodily motions when handling unpackaged replace-
Do not test high voltage by "drawing an arc". ment ES devices. (Otherwise harmless motion such as the
3. Do not spray chemicals on or near this receiver or any of its brushing together of your clothes fabric or the lifting of your
assemblies. foot from a carpeted floor can generate static electricity suf-
4. Unless specified otherwise in this service manual, clean ficient to damage an ES device.)
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable General Soldering Guidelines
non-abrasive applicator; 10 % (by volume) Acetone and 90 % 1. Use a grounded-tip, low-wattage soldering iron and appropri-
(by volume) isopropyl alcohol (90 % - 99 % strength) ate tip size and shape that will maintain tip temperature within
CAUTION: This is a flammable mixture. the range or 500 °F to 600 °F.
Unless specified otherwise in this service manual, lubrication 2. Use an appropriate gauge of RMA resin-core solder composed
of contacts in not required. of 60 parts tin/40 parts lead.
5. Do not defeat any plug/socket B+ voltage interlocks with which 3. Keep the soldering iron tip clean and well tinned.
receivers covered by this service manual might be equipped. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
6. Do not apply AC power to this instrument and/or any of its bristle (0.5 inch, or 1.25 cm) brush with a metal handle.
electrical assemblies unless all solid-state device heat sinks Do not use freon-propelled spray-on cleaners.
are correctly installed. 5. Use the following unsoldering technique
7. Always connect the test receiver ground lead to the receiver a. Allow the soldering iron tip to reach normal temperature.
chassis ground before connecting the test receiver positive (500 °F to 600 °F)
lead. b. Heat the component lead until the solder melts.
Always remove the test receiver ground lead last. c. Quickly draw the melted solder with an anti-static, suction-
8. Use with this receiver only the test fixtures specified in this type solder removal device or with solder braid.
service manual. CAUTION: Work quickly to avoid overheating the circuit
CAUTION: Do not connect the test fixture ground strap to any board printed foil.
heat sink in this receiver. 6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
Electrostatically Sensitive (ES) Devices (500 °F to 600 °F)
Some semiconductor (solid-state) devices can be damaged eas- b. First, hold the soldering iron tip and solder the strand
ily by static electricity. Such components commonly are called against the component lead until the solder melts.
Electrostatically Sensitive (ES) Devices. Examples of typical ES c. Quickly move the soldering iron tip to the junction of the
devices are integrated circuits and some field-effect transistors component lead and the printed circuit foil, and hold it there
and semiconductor “chip” components. The following techniques only until the solder flows onto and around both the compo-
should be used to help reduce the incidence of component dam- nent lead and the foil.
age caused by static by static electricity. CAUTION: Work quickly to avoid overheating the circuit
1. Immediately before handling any semiconductor component or board printed foil.
semiconductor-equipped assembly, drain off any electrostatic d. Closely inspect the solder area and remove any excess or
charge on your body by touching a known earth ground. Alter- splashed solder with a small wire-bristle brush.
natively, obtain and wear a commercially available discharg-
ing wrist strap device, which should be removed to prevent
potential shock reasons prior to applying power to the unit
under test.
Copyright © LG Electronics. Inc. All rights reserved. -4- LGE Internal Use Only
Only for training and service purposes
IC Remove/Replacement 3. Solder the connections.
Some chassis circuit boards have slotted holes (oblong) through CAUTION: Maintain original spacing between the replaced
which the IC leads are inserted and then bent flat against the cir- component and adjacent components and the circuit board to
cuit foil. When holes are the slotted type, the following technique prevent excessive component temperatures.
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique Circuit Board Foil Repair
as outlined in paragraphs 5 and 6 above. Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
Removal board causing the foil to separate from or "lift-off" the board. The
1. Desolder and straighten each IC lead in one operation by following guidelines and procedures should be followed when-
gently prying up on the lead with the soldering iron tip as the ever this condition is encountered.
solder melts.
2. Draw away the melted solder with an anti-static suction-type At IC Connections
solder removal device (or with solder braid) before removing To repair a defective copper pattern at IC connections use the
the IC. following procedure to install a jumper wire on the copper pattern
Replacement side of the circuit board. (Use this technique only on IC connec-
1. Carefully insert the replacement IC in the circuit board. tions).
2. Carefully bend each IC lead against the circuit foil pad and
solder it. 1. Carefully remove the damaged copper pattern with a sharp
3. Clean the soldered areas with a small wire-bristle brush. knife. (Remove only as much copper as absolutely necessary).
(It is not necessary to reapply acrylic coating to the areas). 2. Carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
"Small-Signal" Discrete Transistor 3. Bend a small "U" in one end of a small gauge jumper wire and
Removal/Replacement carefully crimp it around the IC pin. Solder the IC connection.
1. Remove the defective transistor by clipping its leads as close 4. Route the jumper wire along the path of the out-away copper
as possible to the component body. pattern and let it overlap the previously scraped end of the
2. Bend into a "U" shape the end of each of three leads remain- good copper pattern. Solder the overlapped area and clip off
ing on the circuit board. any excess jumper wire.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the corresponding At Other Connections
leads extending from the circuit board and crimp the "U" with Use the following technique to repair the defective copper pattern
long nose pliers to insure metal to metal contact then solder at connections other than IC Pins. This technique involves the
each connection. installation of a jumper wire on the component side of the circuit
board.
Power Output, Transistor Device
Removal/Replacement 1. Remove the defective copper pattern with a sharp knife.
1. Heat and remove all solder from around the transistor leads. Remove at least 1/4 inch of copper, to ensure that a hazardous
2. Remove the heat sink mounting screw (if so equipped). condition will not exist if the jumper wire opens.
3. Carefully remove the transistor from the heat sink of the circuit 2. Trace along the copper pattern from both sides of the pattern
board. break and locate the nearest component that is directly con-
4. Insert new transistor in the circuit board. nected to the affected copper pattern.
5. Solder each transistor lead, and clip off excess lead. 3. Connect insulated 20-gauge jumper wire from the lead of the
6. Replace heat sink. nearest component on one side of the pattern break to the
lead of the nearest component on the other side.
Diode Removal/Replacement Carefully crimp and solder the connections.
1. Remove defective diode by clipping its leads as close as pos- CAUTION: Be sure the insulated jumper wire is dressed so the
sible to diode body. it does not touch components or sharp edges.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and
if necessary, apply additional solder.
Copyright © LG Electronics. Inc. All rights reserved. -5- LGE Internal Use Only
Only for training and service purposes
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
4. General Specification
No. Item Specification Remarks
1 Market EU(PAL Market-37Countries) DTV & Analog (Total 37 countries)
DTV (MPEG2/4, DVB-T) :37 countries
UK/Italy/Germany/France/Spain/Sweden/Finland/Netherlands/
Belgium/Luxemburg/ Greece/Denmark/Czech/Austria /Hungary/
Swiss/Croatia/TurkeyNorway/Slovenia/Poland/Ukraine/Portu-
gal/Ireland/Morocco/Latvia/Estonia/Lithania/Rumania/Bulgaria/
Russia/SlovakiaBosnia/Serbia/Albania/Kazakhstan/Belarus
Copyright © LG Electronics. Inc. All rights reserved. -6- LGE Internal Use Only
Only for training and service purposes
No. Item Specification Remarks
Analogue TV Analogue TV :
1) PAL-B/G/D/K/I (RF) VHF: E2 to E12, UHF : E21 to E69
2) SECAM-B/G/D/K/I, SECAM L/L’ (CATV) S1 to S20, HYPER: S21 to S47
► DVB-T2
- Guard Interval(Bitrate_Mbit/s)
: 1/4, 1/8, 1/16, 1/32, 1/128, 19/128, 19/256
- Modulation : Code Rate
QPSK : 1/2, 2/5, 2/3, 3/4, 5/6
Analog : Upper Heterodyne 16-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
3 Receiving system Digital : COFDM, QAM 64-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
256-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
► DVB-C
- Symbolrate : 4.0Msymbols/s to 7.2Msymbols/s
- Modulation : 16QAM, 64-QAM, 128-QAM and 256-QAM
► DVB-S/S2
- symbolrate
DVB-S2 (8PSK / QPSK) : 2 ~ 45Msymbol/s
DVB-S (QPSK) : 2 ~ 45Msymbol/s
- viterbi
DVB-S mode : 1/2, 2/3, 3/4, 5/6, 7/8
DVB-S2 mode : 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10
4 Scart Jack (1EA) PAL, SECAM Scart 1 Jack is Full scart and support RF-OUT(analog), EU only
Component & AV Video Input RCA(PAL, SECAM, NTSC) 4 System : PAL, SECAM, NTSC, PAL60
5
Common port (1EA) Component Input (Y/Cb/Cr, Y/Pb/Pr)
6 HDMI Input (1EA) HDMI-DTV Support HDCP
7 Audio Input (1EA) Component & AV Component & AV’s audio input is used by common port.
8 USB (1EA) EMF, DivX HD, For SVC (download) JPEG, MP3, DivX HD
CI : U
K, Finland, Denmark, Norway, Sweden, Russia, Spain,
DVB-T Ireland, Luxemburg, Belgium, Netherland
CI+ : France(Canal+), Italy(DGTVi)
9 DVB CI : Switzerland, Austria, Slovenia, Hungary, Bulgaria
DVB-C CI+ : S
witzerland(UPC,Cablecom), Netherland(Ziggo),
Germany(KDG,CWB), Finland(labwise)
DVB-S CI + : Germany(Astra HD+)
10 Ethernet (1EA) Wired, DMP only Only UK T2 Model : for MHEG
Copyright © LG Electronics. Inc. All rights reserved. -7- LGE Internal Use Only
Only for training and service purposes
5. Video resolutions (2D)
5.1. Component Input (Y, CB/PB, CR/PR)
No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Proposed
1 720*576 15.625 50.00 13.5 SDTV ,DVD 576I
2 720*480 15.73 60.00 13.5135 SDTV ,DVD 480I
3 720*480 15.73 59.94 13.50 SDTV ,DVD 480I
4 720*576 31.25 50.00 27.00 SDTV 576P
5 720*480 31.50 60.00 27.027 SDTV 480P
6 720*480 31.47 59.94 27.00 SDTV 480P
7 1280*720 37.50 50.00 74.25 HDTV 720P
8 1280*720 45.00 60.00 74.25 HDTV 720P
9 1280*720 44.96 59.94 74.176 HDTV 720P
10 1920*1080 28.125 50.00 74.25 HDTV 1080I
11 1920*1080 33.75 60.00 74.25 HDTV 1080I
12 1920*1080 33.72 59.94 74.176 HDTV 1080I
13 1920*1080 56.25 50.00 148.50 HDTV 1080P
14 1920*1080 67.50 60.00 148.50 HDTV 1080P
15 1920*1080 67.432 59.94 148.352 HDTV 1080P
16 1920*1080 27.00 24.00 74.25 HDTV 1080P
17 1920*1080 26.97 23.94 74.176 HDTV 1080P
18 1920*1080 33.75 30.00 74.25 HDTV 1080P
19 1920*1080 33.71 29.97 74.176 HDTV 1080P
Copyright © LG Electronics. Inc. All rights reserved. -8- LGE Internal Use Only
Only for training and service purposes
5.2. HDMI Input(PC/DTV)
No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark
PC(DVI) DDC
1 640*350 31.46 70.09 25.17 EGA X
2 720*400 31.46 70.08 28.32 DOS O
3 640*480 31.46 59.94 25.17 VESA(VGA) O
4 800*600 37.87 60.31 40.00 VESA(SVGA) O
5 1024*768 48.36 60.00 65.00 VESA(XGA) O
6 1152*864 54.34 60.05 80.00 VESA O
7 1360*768 47.71 60.01 85.50 VESA (WXGA) O
8 1280*1024 63.98 60.02 108.0 VESA (SXGA) O FHD only
9 1920*1080 67.50 60.00 148.5 HDTV 1080P O FHD only
DTV
1 640*480 31.46 59.94 25.125 SDTV 480P
2 640*480 31.50 60.00 25.125 SDTV 480P
3 720*480 15.73 59.94 13.500 SDTV 480I
Don’t insert in manual
4 720*480 15.75 60.00 13.514 SDTV 480I
spec. out
5 720*576 15.62 50.00 13.500 SDTV 576I(DVB)
6 720*480 31.47 59.94 27.00 SDTV 480P
7 720*480 31.50 60.00 27.027 SDTV 480P
8 720*576 31.25 50.00 27.00 SDTV 576P(DVB)
9 1280*720 37.50 50.00 74.25 HDTV 720P(DVB)
10 1280*720 45.00 60.00 74.25 HDTV 720P
11 1280*720 44.96 59.94 74.176 HDTV 720P
12 1920*1080 28.12 50.00 74.25 HDTV 1080I(DVB)
13 1920*1080 33.75 60.00 74.25 HDTV 1080I
14 1920*1080 33.72 59.94 74.176 HDTV 1080I
15 1920*1080 56.25 50.00 148.50 HDTV 1080P(DVB)
16 1920*1080 67.50 60.00 148.50 HDTV 1080P
17 1920*1080 67.43 59.94 148.35 HDTV 1080P
18 1920*1080 27.00 24.00 74.25 HDTV 1080P
19 1920*1080 26.97 23.97 74.175 HDTV 1080P
20 1920*1080 33.75 30.00 74.25 HDTV 1080P
21 1920*1080 33.71 29.97 74.175 HDTV 1080P
Copyright © LG Electronics. Inc. All rights reserved. -9- LGE Internal Use Only
Only for training and service purposes
ADJUSTMENT INSTRUCTION
1. Application Range (4) Click "Connect" tab. If "Can't" is displayed, check connection
between computer, jig, and set.
This specification sheet is applied to all of the LED TV with
LD55C chassis.
(2) (3)
2. Designation
(1) The adjustment is according to the order which is designated
and which must be followed, according to the plan which
can be changed only on agreeing.
(2) Power adjustment : Free Voltage.
(3) Magnetic Field Condition: Nil.
(4) Input signal Unit: Product Specification Standard.
(5) Reserve after operation : Above 5 Minutes (Heat Run) Please Check the Speed :
Temperature : at 25 °C ± 5 °C To use speed between
Relative humidity : 65 ± 10 % from 200KHz to 400KHz
Input voltage : 220 V, 60 Hz
(6) Adjustment equipments: Color Analyzer(CA-210 or CA-110), (5) Click "Auto" tab and set as below.
DDC Adjustment Jig, Service remote control. (6) Click "Run".
(7) Push the "IN STOP" key - For memory initialization. (7) After downloading, check "OK" message.
Copyright © LG Electronics. Inc. All rights reserved. - 10 - LGE Internal Use Only
Only for training and service purposes
* After downloading, have to adjust Tool Option again. 3.3. EDID data
(1) Push "IN-START" key in service remote control. (1) 2D FHD Model HDMI EDID data
(2) Select "Tool Option 1" and push "OK" key. 0 1 2 3 4 5 6 7 8 9 A B C D E F
(3) Punch in the number. (Each model has their number) 00 00 FF FF FF FF FF FF 00 1E 6D a b
(4) Completed selecting Tool option. 10 c 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
<Caution> U sing "P-ONLY" key of the Adjustment remote b. Serial No: Controlled on production line.
control, power on TV. c. Month, Year:
ex) Week : '01' -> '01'
* ADC Calibration Protocol (RS232) Year : '2015' -> '19' fix
No. Item CMD 1 CMD 2 Data 0
d. Model Name(Hex):
Enter Adjust Adjust When transfer the ‘Mode In’, cf) TV set’s model name in EDID data is below.
A A 0 0 MODEL NAME(HEX)
MODE ‘Mode In’ Carry the command.
ADC Automatically adjustment LG TV 00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 (LG TV)
ADC adjust A D 1 0
Adjust (The use of a internal pattern)
f. Vendor Specific(HDMI)
3.2. EDID Download
▪ After enter Service Mode by pushing "ADJ" key. INPUT Model name(HEX)
▪ Enter EDID D/L menu. HDMI1 67 03 0C 00 10 00 80 1E
▪ Enter "START" by pushing "OK" key.
EZ ADJUST EDID D/L
0. Tool Option1
1. Tool Option2
HDMI1 NG
HDMI2 NG
3.4. Function Check
2. Tool Option3
3. Tool Option4 Start Reset
- Check display and sound
4. Tool Option5 ■ Check Input and Signal items.
5. Tool Option6
6. Country Group 1) TV
7. Area Option
8. ADC Calibration 2) AV (SCART / CVBS)
9. White Balance
10. 10 Point WB
3) COMPONENT (480i)
11. Test Pattern 4) HDMI
12. EDID D/L ►
13. Sub B/C * Display and Sound check is executed by Remote control.
14. Ext. Input Adjust
Copyright © LG Electronics. Inc. All rights reserved. - 11 - LGE Internal Use Only
Only for training and service purposes
4. Total Assembly line process ▪ Auto adjustment Map(using RS-232C to USB cable)
RS-232C COMMAND
4.1. White Balance adjustment [CMD ID DATA]
▪ W/B Equipment condition Wb 00 00 White Balance Start
CA210 : LED → CH14, Test signal: Inner pattern(80IRE) Wb 00 ff White Balance End
▪ Above 5 minutes H/run in the inner pattern. (“power on” key
of adjust remote control) RS-232C COMMAND CENTER
[CMD ID DATA] MIN (DEFAULT) MAX
▪ If it is executed W/B adjustment in 2~3 minutes H/run, it is
adjusted by Target data. Cool Mid Warm Cool Mid Warm
Mode Temp Coordinate spec Target R Gain jg Ja jd 00 172 192 192 254
X = 0.271 (± 0.002) X = 0.278 G Gain jh Jb je 00 172 192 192 192
Cool 13,000 K
Y = 0.270 (± 0.002) Y = 0.280
B Gain ji Jc jf 00 192 192 172 254
X = 0.286 (± 0.002) X = 0.293
Medium 9,300 K R Cut 64 64 64 128
Y = 0.289 (± 0.002) Y = 0.299
X = 0.313 (± 0.002) X = 0.320 G Cut 64 64 64 128
Warm 6,500 K
Y = 0.329 (± 0.002) Y = 0.339 B Cut 64 64 64 128
Luminance
Min 60 (LF51 Series Model) <Caution>
(cd/m2)
Color Temperature : COOL, Medium, Warm.
▪ For LGD, BOE, AUO, CSOT.. Module.(In the case of , the One of R Gain/G Gain/ B Gain should be kept on 0xC0, and
color temperature spec of cool mode is 13000K) adjust other two lower than C0.(When R/G/B Gain are all
Cool Medium Warm C0, it is the FULL Dynamic Range of Module)
x y x y x y
spec 271 270 286 289 313 329 * Manual W/B process using adjust Remote control.
target 278 280 293 299 320 339 ▪ After enter Service Mode by pushing "ADJ" key,
▪ W/B information ▪ E nter White Balance by pushing " ► " key at "9. White
Model information W/B information
Balance".
Model Module Panel Backlight Type Using W/B table EZ ADJUST
0. Tool Option1
All All All Direct LED O 1. Tool Option2
Whit Balance
2. Tool Option3 Color Temp. ◄ Cool ►
3. Tool Option4 R-Gain 172
* Connecting picture of the measuring instrument 4. Tool Option5 G-Gain 172
5. Tool Option6 B-Gain 192
(On Automatic control) 6. Country Group R-Cut 64
Inside PATTERN is used when W/B is controlled. Connect to 7. Area Option G-Cut 64
8. ADC Calibration B-Cut 64
auto controller or push Adjustment R/C P-ONLY → Enter the 9. White Balance Test-Pattern ON
mode of White-Balance, the pattern will come out. 10. 10 Point WB Backlight 100
11. Test Pattern Reset To Set
12 EDID D/L
13. Sub B/C
14. Ext. Input Adjust
Full White Pattern CA-210
Copyright © LG Electronics. Inc. All rights reserved. - 12 - LGE Internal Use Only
Only for training and service purposes
* CASE Medium / Warm
First adjust the coordinate far away from the target
5. GND and HI-POT Test
value(x, y). 5.1. HI-POT auto-check preparation
1) x, y > target - Check the POWER cable and SIGNAL cable insertion condition
i) Decrease the R, G.
2) x, y < target 5.2. HI-POT auto-check
i) First decrease the B gain, (1) Pallet moves in the station. (POWER CORD / AV CORD is
ii) Decrease the one of the others. tightly inserted)
3) x > target, y < target (2) Connect the AV JACK Tester.
i) First decrease B, so make y a little more than the target. (3) Controller (GWS103-4) on.
ii) Adjust x value by decreasing the R (4) HI-POT test (Auto)
4) x < target, y > target - If Test is failed, Buzzer operates.
i) First decrease B, so make x a little more than the target. - If Test is passed, GOOD Lamp on and move to next
ii) Adjust x value by decreasing the G process automatically.
CMD : A0h
LENGTH : 85~94h (1~16 bytes)
ADH : EEPROM Sub Address high (00~1F)
ADL : EEPROM Sub Address low (00~FF)
Data : Write data
CS : CMD + LENGTH + ADH + ADL + Data_1 +...+ Data_n
Delay : 20ms
Copyright © LG Electronics. Inc. All rights reserved. - 13 - LGE Internal Use Only
Only for training and service purposes
6.2. Command Set 7. MAC Address & CI+ key download
Adjust mode CMD(hex) LENGTH(hex) Description 7.1. MAC Address
EEPROM WRITE A0h 84h+n n-bytes Write(n= 1~16) 7.1.1. Equipment & Condition
* Description ▪ Play file : Serial.exe
FOS Default write : <7mode data> write ▪ MAC Address edit
Vtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0, ▪ Input Start / End MAC address
Phase
Data write : Model Name and Serial Number write in EEPROM,. 7.1.2. Download method
(1) Communication Prot connection
6.3. Method & notice
(1) Serial number D/L is using of scan equipment.
(2) S etting of scan equipment operated by Manufacturing
Technology Group.
(3) Serial number D/L must be conformed when it is produced in
production line, because serial number D/L is mandatory by
D-book 4.0. Connection: PCBA(USB Port) → USB to Serial Adapter(UC-
232A) → RS-232C cable → PC(RS-232C port)
* Manual Download(Model Name and Serial Number) * Caution: LJ21* chassis support only UC-232A driver. (only
If the TV set is downloaded by OTA or Service man, sometimes
use this one.)
model name or serial number is initialized.(Not always)
There is impossible to download by bar code scan, so It need
Manual download. (2) MAC Address & CI+ Key Download
1) Press the "Instart" key of Adjustment remote control. ▪ Set CI+ Key path Directory at Start Mac & CI+ Download
2) Go to the menu "6.Model Number D/L" like below photo. Programme
3) Input the Factory model name or Serial number like photo. ▪ Com 1,2,3,4 and 115200(Baudrate)
GP4_LOW
4) Check the model name Instart menu. → Factory name displayed.
ex 47LF560V-ZA)
5) Check the Diagnostics.(DTV country only) → Buyer model
displayed.(ex 47LF560V-ZA)
Copyright © LG Electronics. Inc. All rights reserved. - 14 - LGE Internal Use Only
Only for training and service purposes
7.2. LAN Inspection
7.2.1. Equipment & Condition
▪ Each other connection to LAN Port of IP Hub and Jig
SET PC
Copyright © LG Electronics. Inc. All rights reserved. - 15 - LGE Internal Use Only
Only for training and service purposes
DISASSEMBLY
1. Disassembly of Back cover
(1) Unscrew bolts in the set. (4) Put ‘long nose’ into the hole.
(3) Attach tape to ‘Long nose pliers’. (6) Disassemble Back cover.
* Scratch can be caused without tape. * Disassemble it from left to right for top
side hook on Back cover
Copyright © LG Electronics. Inc. All rights reserved. - 16 - LGE Internal Use Only
Only for training and service purposes
Copyright ©
SPI_SCK/SDI/SDO/CS Serial Flash
1. 49LF510V-ZA
(IC1300, 8Mbit)
NAND FLASH
- 17 -
TU_SCL / SDA (IC101, DDR3 256MB) NTP7515
AMP_SCL/SDA
(IC5600)
IF_AGC
SPK_R
CK+/-, D0+/-, D1+/-, D2+/-_HDMI2
HDMI1
(JK801) DDC_SCL/SDA_2, HDMI_CEC Jog KEY, LED_R, IR Connector
(P4601)
BLOCK DIAGRAM
DM/DP
REAR (P1800)
USB OCP (P1801)
(JK700) +5V_USB USB1_OCP/CTL
SN1406035RGER
RXA0+/-~RXA4+/-, RXACK+/-
LAN EPHY_TP/TN/RP/RN RXB0+/-~RXB4+/-, RXBCK+/-
(JK2100)
Only UK
SC1/AV2_CVBS_IN, SC1_R+/G+/B+
F-SCART
30P HD LVDS wafer
DTV/MNT_OUT, DTV/MNT_L/R_OUT
51P FHD LVDS wafer
(JK2800)
Tuner
(TU3701)
Main SOC
IF_N/P AUD_MASTER_CLK,
H/NIM
M1A-LGE2134 AUD_LRCH, SPK_L
TU_SCL / SDA AUD_LRCK, AUD_SCK
- 18 -
(IC101, DDR3 256MB) NTP7515
IF_AGC AMP_SCL/SDA
(IC5600)
SPK_R
CK+/-, D0+/-, D1+/-, D2+/-_HDMI2
HDMI1
(JK801) DDC_SCL/SDA_2, HDMI_CEC
Jog KEY, LED_R, IR Connector
REAR (P4601)
DM/DP
USB OCP
(JK700) +5V_USB USB1_OCP/CTL (P1800)
SN1406035RGER (P1801)
COMPONENT
30P HD LVDS wafer
COMP2_Y+/Pb+/Pr+/L_R_IN or AV_CVBS_IN/L_R_IN
400
900
LV1
540
901
800
701
120
700
200
Set + Stand
500
A10
A2
Copyright © LG Electronics. Inc. All rights reserved. - 19 - LGE Internal Use Only
Only for training and service purposes
POWER
FROM ADAPTOR 19V
D
R410
+19V 10K
+3.5V_ST +3.3V_Normal
G
+3.5V_ST
POWER_DET
IC402 OPT FET_TOSHIBA
R478 OPT
MP2315GJ C400 C490 Q406
ZD408 L410
100K 0.1uF 1uF SSM3J332R
5V BLM18PG121SN1D
16V 10V
D
S
R471 R485
JK400 39K AAM FB 56K
1 8
KJA-DC-1-0032 OPT
Q407 1/16W TVS_SEMTECH
C428 C429 C430
G
SSM3J332R CYNTEC R443 R447 ZD402
4 1% IN VCC 2.2uF 0.1uF 22uF
4 4.7K 22K
NEW L471-*1
D
2 7 5V
S
D
S
1K
1% OPT R451 R452
C425 R445 C427
33K 0.22uF 5.6K 5.6K
G
0.1uF
25V 25V
R446
120K
C
+3.5V_Normal to +1.5V_DDR
R442 TR_NXP
C
10K TR_KEC
B Q403 B Q403-*1
PANEL_CTL MMBT3904(NXP) +3.3V_Normal
2N3904S +1.5V_DDR
R441 E E
1.3A
10K
L409 IC404 L411
AZ1117EH-ADJTRG1 CB2012PK501T
BLM18PG121SN1D
IN OUT
ADJ/GND BRAZIL_ESD
+3.5V_ST C426 R449 R453 ZD403
10uF 1K R1 0 2.5V
10V 1/16W
19V TO PANEL VCC(12V) DCDC CONVERTER 1% C431
OPT 10uF
R490 R450 10V
200 R2
OPT 10K 1/16W
1%
R489
10K
+19V RL_ON +12V
R480 Vout=1.25*(1+R2/R1)+Iadj*R2
10K
POWER_ON/OFF_1
IC403 OPT
C477
MP2315GJ 0.47uF
16V
R470 R481
100K AAM FB 56K
1 8
TDK
IN
2 NEW 7
VCC
CYNTEC
L470-*1
10uH
L470
10uH +5V_Normal & +1.10V_VDDC
OPT
C470
10uF
25V
C472
0.1uF
25V
SW
3 3A 6
EN/SYNC C480
10uF
16V
C481
10uF
16V
C486
10uF
C483
0.1uF
25V
R482
11K
1%
ZD405
15V
Vout=0.6(R1/R2)+0.6
16V
GND BST 20130528 cJ.LIM +12V +1.10V_VDDC
4 5 R483
3.3K TDK
R475 OPT C478 1% L405
68 R476 0.1uF 4.7uH
47K 25V
C475 CYNTEC
0.1uF
R484 L404 R1 OPT
1K C410 L405-*1 C411 OPT C412 C413 C414
50V 1% CB2012PK501T 4.7uH R411
0.047uF 4.7K 82pF ZD407 ZD401 10uF 22uF 22uF
25V 5.1v 2.5V
1% 50V 6.3V 10V 10V
C405 C406 R2
C407
10uF 10uF 1uF
25V 25V 10V R413
5.1K
1%
PGND1
C416
+3.3V_Normal
[EP]
VIN1
BST1
OPT C408 22pF
SS1
V7V
LX1
2200pF 50V
50V
24
23
22
21
20
19
2200pF R414 3300pF
R403 50V SS2 COMP1 10K 50V R415
10K 1 18 100
THERMAL 1%
EN1 25
FB1
2 17 R2
EN2 AGND R416
R409 3 IC400 16 R422 5.1K
91K ROSC/SYNC RSET 15K 1%
OPT OPT SN1406035RGER
C403 R473 4 15
4700pF 30K SW_EN FB2
50V 5 14
C419 22pF R1
NFAULT COMP2 50V R417
6 13 C418
39K
10
11
12
C420 47pF
1%
9
R418 3300pF 50V
USB1_CTL 20K 50V
+5V_Normal
SW_OUT
SW_IN
VIN2
PGND2
LX2
BST2
USB1_CTL_Pull_Down +5V_Normal
R472
3.3K TDK
Check the pull down C421 L406
R408 0.047uF
when AC Power On with HDD 100K 25V 4.7uH
USB1_OCD
CYNTEC
C491 L406-*1 C423 C424
+5V_Normal 470pF 4.7uH 22uF 22uF
+5V_USB 50V 16V 16V
R491
5.1
C432
1uF
16V
Vout=0.6(R1/R2)+0.6
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
TOTAL LED DRIVER BLOCK
L505
CIS21J121
32_43inch
49inch
+19V D503 43_49inch 49inch
49inch
MBRD10U100CT L501 L502 To Improve EMI Issue D502
L500 49inch A1
33uH L507 VOUT#1=50.5V 33uH 33uH UF3D(SUZHOU GRANDE)
C REDUCE RIPPLE CURRENT
49inch A2
L508 49inch 49inch 49inch 49inch 49inch 32_43inch_AJ_KR_CO C523 32_43inch
C500 C501 C502 C511 C512 C513 C514 R515 C537 C526 D504
47uF 10uF 0.1uF 33uF 33uF 33uF 1uF 100K 100V 100V
4.7uF 49inch 220pF BR210
25V 25V 50V 100V 100V 100V 50V 1/8W
50V C537-*1
+3.3V_Normal 220pF
OPT 49inch 10uF
49inch 49inch 32_43inch_AJ_KR_CO C524 C527 100V
C505 35V 100V 100V
R504 R505 49inch C538
100pF 180K 180K 49inch 4.7uF 220pF 220pF
To Improve EMI Issue C515
R516 50V 49inch
50V 1uF 100K C538-*1
49inch 50V 1/8W 10uF
IC500 49inch 49inch OPT R535 R536 R537 R538 R539 R540 R541 R547 R549 R550
C531 35V 100 100 100 100 100 100 100 100 100 100
TPS40210DGQR [EP] C530 C532
100V 100V 100V
220pF 220pF 220pF OPT
R519 R523 R528
RC VDD 10K 3K 1K
1 10
D
49inch 49inch IC501 49inch
49inch
THERMAL
R511
R513
R558
49inch
49inch
49inch
49inch
1% R531 C522
R506
R508
R503 C506 R520 +19V Q502
100K DT1641AS
47
47
47
11
47
47
2 9 B TR501 1% G SMN630LD
MMBT3904(NXP) 50V
49inch 1/16W 16V D S 32_43inch
49inch
BOOST_EN
R500
1K DIS/EN
3 8
GDRV
R509
49inch 3.3 G
Q500
AOD478
INV_CTL 49inch
E EN
1 24
VIN
Q502-*1
D
OPT R522-*1 32_43inch C510
THERMAL
S 150K
OPT OPT R583 R522 R525 1uF G
EU_BR
25
COMP ISNS D505 R582 10K 120K 270K OVP VREF C525 1uF 25V
R553 4 7 1N4148W-G 2.2 2 23 S
0 32inch
1/8W C521 25V
R529
FB GND 1% 30K 1000pF NC_1 CS AOD2922
R554 5 6 49inch 3 22
0 1% 50V
49inch
R510
R518
3.9K 43inch 49inch
47K
R529-*1 R529-*2 R544
32_43inch_AJ_KR_CO 1% 13K 8.2K PGND_1 NDRV 3.3
R555 4 21
0 1% 1%
49inch 1/16W
49inch 49inch 49inch PWM_DIM R521
49inch
C503 PGND_2 RSS R545 R548
49inch
C507 C508 C509 100
R512
R514
OPT 0.033uF 1uF 0.1uF 330pF 49inch 5 20
0.1
0.1
25V
1W
1W
C516 50V 50V 50V R524 220K 1% 30K 1%
0.1uF R507 C518
49inch
49inch
3.9K 100K 100pF C528
PDIM COMP
R581
C504 1% 50V 6 19
470pF
1K
50V OPT 4700pF
OPT 49inch R530 50V
C517 R501 100K RISET RT
0.1uF 7 18
18K
1% 49inch 43inch 32inch
121211 BLU_CURRENT_CTL R532-*2 R532-*1 R532 R551
49inch 15K LS8 LS1 R546 C529
1K -> 3.9K 27K 12K 8 17 0.1
OPT R502 1%
L503 220p -> 330p 1% 1% 32inch
R533-*2
1K 49inch 1.5K 1%0.1uF
UBW2012-121F R533 25V
43inch 3.6K LS7 LS2
1%
1/16W
3.3K
1% R533-*1 9 16
1%
10K
VOUT = VREF*(1+48.8K/680) 1% R542
OPT LS6 LS3
L504 = 0.7 *(1+48.8K/680) 49inch 10 15
39K
UBW2012-121F 1%
= 50.5V R517
680
1/8W LS5 LS4
11 14 R543
1% 1.5K
10K
1%
R534
NC_2 LGND
12 13
ZD500
33V
FIRST BOOST UP EXCEPT C500 C501
43_49inch 49inch
C535 C519 C540
C533
33uF 4.7uF 1uF 1uF
32inch
P500 50V 100V C519-*1 100V
SMAW200-04 4.7uF
32_43inch 50V
R580
0 49inch 49inch
1 49inch C536 C520 C541
R579 4.7uF 1uF 32_43inch 1uF
0 50V 100V C520-*1 100V
32_43inch 0
2 R578
0 1/4W
5%
C539
3 C534
33uF 4.7uF
VOUT#2 50V
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
USB
USB_HDD_CAP1_10uF USB_HDD_CAP2_10uF +5V_USB
C700-*1 C703-*1
10uF 10uF
10V 10V
R700
2.2
2 SIDE_USB1_DM
R701
2.2
3 SIDE_USB1_DP
OPT OPT OPT
C701 C702 D700
4 5pF 5pF RCLAMP0502BA
50V 50V
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
HDMI (REAR 1)
HDMI_1
5V_HDMI_4 5V_DET_HDMI_4
R814
33
HPD4
ESD_HDMI_VARISTAR
ESD_HDMI
VA805
VA808
GND AR801
100
20 DDC_SDA_4
19 HP_DET DDC_SCL_4
18 5V
ESD_HDMI ESD_HDMI
VA809 VA810
17 GND R812
CEC R804
100
16 DDC_DATA
1.8K R813
3.3K
14 NC ESD_HDMI
HDMI_ARC
VA811
HDMI_DIODE_SUZHOU CE_REMOTE
D801-*1 13
EAG59023302
MMBD6100 AR804
12 CK- L801 5.1
A1
A2
DLP11SA900HL2L
CK_GND 4 3
CK-_HDMI4
11
L802 1 2
CK+_HDMI4
CK+ DLP11SA900HL2L
10 D0-_HDMI4
C
4 3
D0- 1 2
D0+_HDMI4
5V_HDMI_4 +5V_Normal 9
D0_GND
8
D0+
A1
A2
HDMI_DIODE_KEC 7
KDS184 D1-
D801 6 AR803
C
D1_GND L803
5.1
5 DLP11SA900HL2L
D1+ 4 3
D1-_HDMI4
4 L804 1 2
D1+_HDMI4
DLP11SA900HL2L
D2- D2-_HDMI4
3 4 3
ESD_HDMI_VARISTAR
DDC_SCL_4 JK801 VA806
ESD_HDMI_CAP ESD_HDMI_CAP
VA805-*1 VA806-*1
1uF 1uF
10V 10V
A20
A-MDQL0 A-MDQL0 B_DDR3_DQL[0]
A16
A-MDQL1 A-MDQL1 B_DDR3_DQL[1]
C19
A-MDQL2 A-MDQL2 B_DDR3_DQL[2]
C15
A-MDQL3 A-MDQL3 B_DDR3_DQL[3]
C20
A-MDQL4 A-MDQL4 B_DDR3_DQL[4]
C14
A-MDQL5 A-MDQL5 B_DDR3_DQL[5]
B21
A-MDQL6 A-MDQL6 B_DDR3_DQL[6]
B15
A-MDQL7 A-MDQL7 B_DDR3_DQL[7]
F18
A-MDQU0 A-MDQU0 B_DDR3_DQU[0]
D19
A-MDQU1 A-MDQU1 B_DDR3_DQU[1]
D17
A-MDQU2 A-MDQU2 B_DDR3_DQU[2]
E21
A-MDQU3 A-MDQU3 B_DDR3_DQU[3]
E19
A-MDQU4 A-MDQU4 B_DDR3_DQU[4]
D20
A-MDQU5 A-MDQU5 B_DDR3_DQU[5]
D18
A-MDQU6 A-MDQU6 B_DDR3_DQU[6]
F20
A-MDQU7 A-MDQU7 B_DDR3_DQU[7]
E9
ZQ
R1109
240
1%
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Serial Flash for SPI boot
+3.5V_ST +3.5V_ST
SPI_FLASH_MACRONIX
OPT IC1300
R1301 MX25L8035EM2I-10G
4.7K C1300
+3.5V_ST 0.1uF
CS# VCC 16V
/SPI_CS 1 8
WP#/SIO2 SCLK
/FLASH_WP 3 6 SPI_SCK
R1302
GND SI/SIO0 33
4 5 SPI_SDI
SPI_FLASH_WINBOND
IC1300-*1
W25Q80DVSSIG
CS VCC
1 8
DO[IO1] HOLD[IO3]
2 7
WP[IO2] CLK
3 6
GND DI[IO0]
4 5
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
LVDS
2
1
3
2
4
3
5
4
6
5
7
6 RXA3+
8
7 RXA3-
9
8
10
9 RXACK+
11
10 RXACK-
12 RXA4+
11
13 RXA4-
12 RXA2+
14 RXA3+
13 RXA2-
15 RXA3-
14
16 RXACK+
15 RXA1+
17 RXACK-
16 RXA1-
18
17
19 RXA2+
18 RXA0+
20 RXA2-
19 RXA0-
21
20
22 RXA1+
21
23 RXA1-
22
24 RXA0+
OPT 23
25 RXA0- R1801
0 24
26
0 25
27
R1812 26
28 RXB4+ OPT
27 PANEL_HD
29 RXB4-
28
30 RXB3+
29
31 RXB3-
30
32 RXBCK+
33 RXBCK- 31
34
35 RXB2+
36 RXB2-
37
38 RXB1+
39 RXB1-
40 RXB0+
OPT
41 RXB0- AR1800
0
1/16W
42
43
44
PANEL_VCC
45
UBW2012-121F
46
L1801
47
48
49 PANEL_HD
50
51
C1800 C1801
52 0.1uF 10uF
25V 25V
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
CI Region * Option name of this page : CI_SLOT
(because of Hong Kong)
CI SLOT
CI_DATA[0-7]
+5V_CI_ON
CI TS INPUT
CI_SLOT
AR1903
CI_DATA[0-7]
+5V_Normal CI_SLOT 33
C1903 FE_TS_DATA[7]
CI_MDI[7]
10uF FE_TS_DATA[6]
CI_SLOT 10V CI_MDI[6]
FE_TS_DATA[0-7]
R1908 FE_TS_DATA[5]
10K CI_MDI[5]
FE_TS_DATA[4]
CI_SLOT CI_MDI[4]
/CI_CD1 P1900 CI_SLOT
10067972-000LF AR1904
CI_SLOT 33 FE_TS_DATA[3]
R1914 35 1 CI_MDI[3]
100 CI_DATA[3] FE_TS_DATA[2]
CI_SLOT 36 2 CI_MDI[2]
AR1900 CI_DATA[4] CI_SLOT FE_TS_DATA[1]
CI_DATA[0-7]
33 37 3 CI_MDI[1] FE_TS_DATA[0]
CI_DATA[5] R1919
CI_TS_DATA[4] 38 4 10K CI_MDI[0]
CI_DATA[6]
CI_TS_DATA[5] 39 5
CI_DATA[7] FE_TS_DATA[0-7]
CI_TS_DATA[6] 40 6
R1917 R1921 33 CI_SLOT
CI_TS_DATA[7] 41 7 47 CI_SLOT CI_MISTRT FE_TS_SYNC
/PCM_CE R1922 33 CI_SLOT
CI_SLOT 42 8 CI_ADDR[10] FE_TS_VAL_ERR
CI_MIVAL_ERR R1923 100 CI_SLOT
R1910 10K 43 9 CI_OE +5V_Normal CI_MCLKI FE_TS_CLK
44 10 CI_ADDR[11]
CI_IORD
45 11 CI_ADDR[9]
CI_IOWR
CI_ADDR[8]
CI_SLOT
46 12
47 13 CI_ADDR[13] R1920
CI_MDI[0] 10K
48 14 CI_ADDR[14]
CI_MDI[1]
CI_MDI[2] 49 15 CI_WE
50 16 R1918 100 CI_SLOT
CI_MDI[3] /PCM_IRQA
CI_SLOT
51 17 CI_SLOT
+5V_Normal
CI_MDI[4]
GND
C1901
0.1uF
52
53
18
19
C1904
0.1uF
CI_SLOT
C1905
0.1uF
CI HOST I/F
GND
CI_SLOT CI_MDI[5] 54 20
R1900 55 21 CI_ADDR[12]
10K CI_MDI[6]
CI_SLOT 56 22 CI_ADDR[7] GND +3.3V_Normal
CI_MDI[7]
R1911 10K CI_ADDR[6]
57 23 CLOSE TO SOC BUFFER_ORG
R1903 47 CI_SLOT 58 24 CI_ADDR[5]
CLOSE TO SOC PCM_RST
CI_ADDR[4] CI_DET
IC1902
R1904 47 CI_SLOT 59 25
/PCM_WAIT 74LCX244FT
60 26 CI_ADDR[3]
REG C1906
R1905 100 CI_SLOT 61 27 CI_ADDR[2] 0.1uF
CI_TS_CLK
R1906 33 CI_SLOT CI_ADDR[1] 1OE VCC 16V
CI_TS_VAL 62 28 1 20
R1907 33 CI_SLOT 63 29 CI_ADDR[0]
CI_TS_SYNC
CI_DATA[0]
AR1901 64 30 1A1 2OE
33 CI_SLOT CI_DATA[1] CI_SLOT 2 19
65 31 CI_ADDR[0-14] PCM_A[0] CI_SLOT
CI_TS_DATA[0] CI_DATA[2] AR1902 AR1910
66 32 100
CI_TS_DATA[1] 2Y4 1Y1 100
67 33 3 18
CI_TS_DATA[2] CI_ADDR[7] CI_ADDR[0]
68 34
CI_TS_DATA[3] CI_ADDR[6] CI_ADDR[1]
G2 69 G1 CI_ADDR[5] 1A2 2A4 CI_ADDR[2]
CI_SLOT PCM_A[1] 4 17 PCM_A[7]
C1900 CI_ADDR[4] CI_ADDR[3]
2pF
50V 2Y3 1Y2
5 16
CLOSE TO SOC
1A3 2A3
PCM_A[2] 6 15 PCM_A[6]
GND GND
+5V_Normal GND
2Y2 1Y3
7 14
CI_SLOT
R1909 CI_SLOT
10K R1912 1A4 2A2
100 PCM_A[3] 8 13 PCM_A[5]
/CI_CD2
BUFFER_NXP
IC1902-*1
74LVC244APW
1OE VCC
1 20
1A0 2OE
2 19
CI_DATA[0-7]
10K CI_DATA[2] PCM_D[2]
CI_DATA[3] PCM_D[3] 2Y2
7 14
1Y2
OR_GATE_CI_NXP
IC1900-*1
1A3 2A2
PCM_D[0-7]
74LVC1G32GW
CI_DET CI_SLOT 8 13
CI_DATA[0-7]
PCM_D[0-7]
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
SCART_COMPONENT
COMPONENT
COMP
JK2601
PPJ245N2-01 COMP
R2606
6E [RD2]E-LUG 10K
COMP COMP2_R_IN
OPT R2601 ATV_330P R2608
[RD2]O-SPRING VA2601 470K 330pF 12K
5E 5.6V C2601
COMP COMP
R2607
4E [RD2]CONTACT 10K
COMP COMP2_L_IN
OPT ATV_330P R2609 +3.3V_Normal
R2602
[WH]O-SPRING VA2602 470K 330pF 12K
5D C2602 COMP
5.6V COMP COMP
R2610
10K R2612
4C [RD1]CONTACT 1K
COMP2_DET
[RD1]O-SPRING OPT
5C VA2606
COMP COMP2_Pr+
ESD_COMP R2603 5.6V
7C [RD1]E-LUG-S ZD2605 VA2603 75
ESD_COMP_ZENER_ROHM 5.5V
5B [BL]O-SPRING ZD2606
ESD_COMP_ZENER_ROHM COMP COMP2_Pb+
ESD_COMP R2604 +3.3V_Normal
4A [GN/YL]CONTACT ZD2603 VA2604 75
ESD_COMP_ZENER_ROHM COMP COMP
5.5V
R2611 R2613
5A [GN/YL]O-SPRING ZD2604 10K 1K
ESD_COMP_ZENER_ROHM AV_CVBS_DET
OPT OPT
[GN/YL]E-LUG VA2605 C2603
6A 5.6V 0.1uF
16V
COMP2_Y+/AV_CVBS_IN
COMP
ZD2601-*1 ZD2601 R2605
75
ESD_COMP_ZENER_KEC ESD_COMP_ZENER_ROHM 3216
ZD2602-*1 ZD2602
ESD_COMP_ZENER_KEC ESD_COMP_ZENER_ROHM
ZD2603-*1
ESD_COMP_ZENER_KEC
ZD2604-*1
ESD_COMP_ZENER_KEC
ZD2605-*1
ESD_COMP_ZENER_KEC
ZD2606-*1
ESD_COMP_ZENER_KEC
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
DVB-S2 LNB Part Allegro
(Option:LNB)
Max 1.3A
+12V +12V_LNB
LNB
3A L2701
BLM18PG121SN1D
+12V_LNB
LNB_SX34
D2705-*1
40V
LNB
LNB
D2703
2A D2705
LNB_SMAB34
L2702
LPH6050T-150M-R
15uH
Caution!! need isolated GND
SS23L 30V 40V 3.5A
R2701
0
LNB
C2708
10uF
LNB LNB LNB LNB
C2703 C2704 C2705 C2706 25V
0.01uF 10uF 10uF 10uF
50V 25V 25V 25V A_GND
A_GND
A_GND
BOOST
0.1uF
[EP]
NC_4
NC_3
PGND
C2707
50V
LX
0.1uF
50V
20
19
18
17
16
LNB NC_1 VIN
1 15
[EP]GND
D2702
close to TUNER SS23L 30V THERMAL
BOOST
GNDLX
LNB 2 14 GND
NC_3
NC_2
LNB_OUT 21
LX
NC_2 LNB_DMB VREG
3 13
IC2701
LNB LNB TDI ISET
20
19
18
17
16
LNB LNB LNB_SMAB34 4 12
LNB LNB LNB LNB
R2702 C2713 C2715 C2712
LNB_SX34 DT1803 VCP VIN
2.2K 0.22uF D2704 D2704-*1 1 15
C2714 C2701 C2702 D2701 1W 2700pF 0.1uF 40V 40V TDO 5 11 TCAP
18pF 18pF 33pF 50V 25V 50V THERMAL
LNB 2 14 GND
21
10
50V 50V 50V LNB LNB LNB
9
C2710 R2703 C2711 NC_1 3 13 VREG
0.1uF 36K 0.22uF IC2701-*1
IRQ
SCL
SDA
ADD
TONECTRL
50V 1/16W 25V TDI A8303SESTR-T
4 12 ISET
1%
Close to Tuner LNB_ALLEGRO
TDO 5 11 TCAP
Surge protectioin
10
A_GND A_GND
9
IRQ
SCL
SDA
ADD
TONECTRL
R2706
0
LNB LNB
R2704 R2705
33 33
DEMOD_SCL
DEMOD_SDA
LNB_TX
CLOSE TO MSTAR
CLOSE TO MSTAR
R2819
10K SCART
SCART R2820
1K
SC1/COMP1_DET
VA2815
5.6V
OPT
SCART
JK2800 SC1/AV2_CVBS_IN
PSC008-01 SCART OPT
R2813 C2801
75 47pF
50V
ESD_SCART
22 VA2807
AV_DET 5.5V
21
COM_GND
SCART
20 R2861
SYNC_IN 10
DTV/MNT_VOUT
19 OPT OPT
SYNC_OUT ESD_SCART SCART C2815 C2816
VA2814 R2821
18 VA2808 5.6V 75 68pF 68pF
SYNC_GND2 20V EUSCART 50V SCART 50V
R2827
17 22
SYNC_GND1
16 SC1_FB
RGB_IO
15 SC1_R+/COMP1_Pr+
R_OUT
SCART
ESD_SCART SCART
VA2810 R2807 R2822
14 75
RGB_GND 20V 75
13
R_GND
12
D2B_OUT
11 SC1_G+/COMP1_Y+
SCART
G_OUT ESD_SCART
VA2811 R2808
10 20V 75
D2B_IN SCART
9 R2824
G_GND 15K
8 SC1_ID
ID
SC1_B+/COMP1_Pb+ ESD_SCART SCART
7 ESD_SCART R2828
VA2817
SCART
B_OUT
VA2812 R2805 20V 3.9K
6 75
AUDIO_L_IN 20V
5
B_GND
4 SCART SCART
AUDIO_GND R2823 R2826
10K
SCART
0
3 SC1/COMP1_L_IN
AUDIO_L_OUT
2 R2806 SCART
AUDIO_R_IN ESD_SCART 470K R2829
VA2813 12K
1 EU
AUDIO_R_OUT 5.6V
SCART SCART
R2858 R2825
0 10K
SCART
SC1/COMP1_R_IN
ESD_SCART
VA2809 SCART
R2809 R2830
5.6V 12K
470K
DTV/MNT_L_OUT
SCART
OPT C2813
VA2806 1000pF
5.6V 50V
DTV/MNT_R_OUT
SCART
OPT C2814
VA2805 1000pF
5.6V 50V
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
ETHERNET
* H/W option : ETHERNET
ETHERNET
JK2100
RJ45VT-01SN002
1
1 EPHY_TP
2
2
3
3
EPHY_TN
4
4 EPHY_RP
5
5
6
6 EPHY_RN
7
7
ETHERNET ETHERNET
8 C2105 C2104
8 0.01uF 0.01uF
50V 50V
9
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
TUNER T/C_T2/C/S2 ISDB-T T2/C
TU_I2C_FILTER
TU_ATSC TU_ATSC R3738-*1
C3705-*1 R3716-*1 MLG1005SR27JT
1.8K
TUNER_T/C TUNER_T2/C/S2 18pF
TU_ATSC
TU_ATSC R3717-*1 TU_I2C_FILTER
TU3702 TU3700 C3707-*1
1.8K R3739-*1
MLG1005SR27JT
18pF
TU_NON_ATSC TU_NON_ATSC
TU_I2C_NON_FILTER R3716 R3717
SCL SCL_RF R3738
33
1K 1K
1 1 TU_SCL
TU_I2C_NON_FILTER
SDA SDA_RF R3739
33 +3.3V_TU
2 2 TU_SDA
TU_NON_ATSC TU_NON_ATSC TU_NON_ATSC TU_NON_ATSC
C3705 C3707 C3710 C3711
B[+3.3V] B1[+3.3V] 20pF 20pF 20pF 20pF
3 3
C3708 C3714
CVBS CVBS 100pF
50V
0.1uF
16V
4 4
IF_AGC AIF_AGC R3714 should be guarded by ground
0
5 5 IF_AGC_MAIN
C3703
SIF SIF 0.1uF
16V
6 6 TU_ATSC
TU_NON_ATSC R3710-*1
IF[N] AIF[N] R3710 10
0
7 7 TU_ATSC
IF_N_MSTAR
R3709-*1
IF[P] AIF[P] TU_NON_ATSC
R3709 10
0
8 8 IF_P_MSTAR
GND_1
9
9 T2
RESET_DEMOD R3719
10 10
DEMOD_RESET
SHIELD T2
C3716 +3.3V_TU
B2[+3.3V] 0.1uF
16V
11 T2 T2
C3718 C3722 T2
F22_OUTPUT 100pF 0.1uF R3707
12 50V 16V 0
LNB_TX
B3[+1.2V] +1.2V_DEMOD
13
T2 T2
ERROR T2 C3713
100pF
C3729
0.1uF
14 AR3700
0
50V 16V
1/16W
MCLK FE_TS_ERR
15 FE_TS_CLK +3.3V_TU +3.3V_Normal
FE_TS_SYNC
SYNC FE_TS_VAL
16
L3704
VALID UBW2012-121F
17 C3730 C3731 C3733 C3738
22uF 0.1uF 22uF 0.1uF
DATA0 10V 16V 10V 16V
18
T2
DATA1 AR3701
0 FE_TS_DATA[0-7]
19 1/16W
FE_TS_DATA[0] T2
IC3701
DATA2 FE_TS_DATA[1]
+3.3V_TU AP7361-Y-13
20 FE_TS_DATA[2]
T2
+1.2V_DEMOD
FE_TS_DATA[3]
R3723
DATA3 3.3K EN
SIGN37000003
1 5
OUT
21 T2 T2
C3725 R3737
1uF GND 1
T2
DATA4
SIGN37000004
10V 2
C3732 T2
22 0.1uF
16V
C3737
10uF
ADJ/NC IN
T2 3 4 10V
DATA5 AR3702
0 T2
23 1/16W R3733
12K
LNB FE_TS_DATA[4]
SIGN37000002
1%
28
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
RS-232C 4PIN
RS-232C 4PIN
RS232C_DEBUG_4P
+3.5V_ST P4000
12507WS-04L
VCC
1
AR4000 PM_RXD
2
PM_RXD 100
1/16W
GND
3
RM_TXD
4
PM_TXD
GND
JP_GND2
JP_GND3
JP_GND4
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
IR
+3.5V_ST
AR4601
1/16W
10K
KEY1
R4606
KEY2 IR_6P
OPT 100
OPT P4602
C4604
0.1uF VR4602 12507WR-06L
16V
+3.5V_ST 1
2
OPT
C4601 C4602
0.1uF 1000pF
16V 50V 3
R4601
1.8K
LED_R/BUZZ 4
+3.5V_ST
5
R4602
6
3.3K
IR 7
C4605 OPT
100pF ZD4601
50V 5V
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
COMP COMP
0.047uF C4908 33 R4907
COMP2/AV_CVBS COMP2_Y+/AV_CVBS_IN
*CAPTION OPT:COMP
C4901 0.047uF R4901 68
BIN1M
C4902 0.047uF R4902 33
BIN1P COMP2_Pb+
C4903 0.047uF R4903 68
GIN1M
C4904 0.047uF R4904 33
GIN1P COMP2_Y+/AV_CVBS_IN
C4905 0.047uF R4905 68
RIN1M
C4906 0.047uF R4906 33
RIN1P COMP2_Pr+
C4907 1000pF
SOGIN1
OPT
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Close to MSTAR
*CAPTION OPT:SCART
C5002 0.047uF R5002 68
BIN0M
C5003 0.047uF R5003 33
BIN0P SC1_B+/COMP1_Pb+
C5004 0.047uF R5004 68
GIN0M
C5005 0.047uF R5005 33
GIN0P SC1_G+/COMP1_Y+
C5006 0.047uF R5006 68
RIN0M
C5007 0.047uF R5007 33
RIN0P SC1_R+/COMP1_Pr+
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
NAND FLASH MEMORY <CHIP Config> PM MODEL OPTION
NAND_FLASH_1G_HYNIX
IC102 (SPI_SDI, PM_LED, PWM_PM) +3.5V_ST PM_MODEL_OPT_0 M1A_128M_UO4 M1A_256M_AVS+
IC101-*1 IC101-*2
H27U1G8F2CTR-BC
LG-NonOS SB51_ExtSPI 3’b000 51boot from SPI - HIGH : LCD M1A_256M_UO4 LGE2133(128M) LGE2136(256M)
EAN35669103
LG-OS HEMCU_ExtSPI 3’b001 MIPS boot from SPI - LOW :: PDP IC101
+3.3V_Normal +3.3V_Normal LCD
R177
10K PM_MODEL_OPT_1 LGE2134(256M) U19
T20
LVA4P/TTL_B[0]/HCONV/GPIO170
LVA4M/TTL_B[1]/E_O/GPIO171
SAR0/GPIO35
SAR1/GPIO36
D5
F8
U19
T20
LVA4P/TTL_B[0]/HCONV/GPIO170
LVA4M/TTL_B[1]/E_O/GPIO171
SAR0/GPIO35
SAR1/GPIO36
D5
F8
+3.5V_ST T21 E7 T21 E7
NC_1 NC_29 - Not Use (Ready) T19
LVA3P/TTL_B[2]/FB/GPIO172
LVA3M/TTL_B[3]/OPT_P/GPIO173
SAR2/GPIO37
SAR3/GPIO38
E6 T19
LVA3P/TTL_B[2]/FB/GPIO172
LVA3M/TTL_B[3]/OPT_P/GPIO173
SAR2/GPIO37
SAR3/GPIO38
E6
1 48 R21 D6 R21 D6
PM_MODEL_OPT_0 R20
LVACKP/TTL_B[4]/MCLK/GPIO174 SAR4/GPIO39
R20
LVACKP/TTL_B[4]/MCLK/GPIO174 SAR4/GPIO39
LVACKM/TTL_B[5]/GCLK/GPIO175 LVACKM/TTL_B[5]/GCLK/GPIO175
NC_2 NC_28 PDP
R19
LVA2P/TTL_B[6]/GST/GPIO176 GPIO_PM[13]/GPIO20
W10 R19
LVA2P/TTL_B[6]/GST/GPIO176 GPIO_PM[13]/GPIO20
W10
2 47 R176 U19 D5 P20
LVA2M/TTL_B[7]/POL/GPIO177 GPIO_PM[14]/GPIO21
Y10 P20
LVA2M/TTL_B[7]/POL/GPIO177 GPIO_PM[14]/GPIO21
Y10
CI_TS_CLK Y1
GPIO78 TS0CLK/GPIO92
V10 Y1
GPIO78 TS0CLK/GPIO92
V10
W4 T14 W4 T14
CI_TS_DATA[0-7] GPIO79 TS0DATA[0]/GPIO82
T13
GPIO79 TS0DATA[0]/GPIO82
T13
Y1 V10 K17
TS0DATA[1]/GPIO83
U13 K17
TS0DATA[1]/GPIO83
U13
GPIO78 TS0CLK/GPIO92 CI_TS_DATA[0] CI_TS_SYNC J15
I2C_SCKM3/I2C_DDCR_CK/GPIO77 TS0DATA[2]/GPIO84
V15 J15
I2C_SCKM3/I2C_DDCR_CK/GPIO77 TS0DATA[2]/GPIO84
V15
NAND_FLASH_2G_HYNIX NAND_FLASH_1G_TOSHIBA_24n W4 T14 U8
I2C_SDAM3/I2C_DDCR_DA/GPIO76 TS0DATA[3]/GPIO85
U12 U8
I2C_SDAM3/I2C_DDCR_DA/GPIO76 TS0DATA[3]/GPIO85
U12
5V_DET_HDMI_4 GPIO79 TS0DATA[0]/GPIO82 CI_TS_DATA[1] CI_TS_VAL SDAM2/GPIO55 TS0DATA[4]/GPIO86 SDAM2/GPIO55 TS0DATA[4]/GPIO86
8 41 8 41 G7 AA13 K5
ET_TX_EN/GPIO63
D8 K5
ET_TX_EN/GPIO63
D8
COMP2_DET I2S_IN_WS/GPIO158 TS1DATA[5]/GPIO98 FE_TS_DATA[6] K4
ET_RXD[0]/GPIO65 HWRESET
E5 K4
ET_RXD[0]/GPIO65 HWRESET
E5
CE NC_25 CE NC_25 W14 H6
ET_MDC/GPIO66 IRIN/GPIO5
G4 H6
ET_MDC/GPIO66 IRIN/GPIO5
G4
9 40 9 40 TS1DATA[6]/GPIO99 FE_TS_DATA[7] L5
ET_MDIO/GPIO67 DDCA_CK/UART0_RX
G5 L5
ET_MDIO/GPIO67 DDCA_CK/UART0_RX
G5
J4 W13 ET_RXD[1]/GPIO68 DDCA_DA/UART0_TX ET_RXD[1]/GPIO68 DDCA_DA/UART0_TX
NC_7 NC_24 NC_7 NC_24 DEMOD_RESET ET_COL/GPIO60 TS1DATA[7]/GPIO100 U17 J18 U17 J18
10 39 10 39 J5 Y15 R18
PCMADR[0]/NF_AD[0]/GPIO130 PWM0/GPIO71
K18 R18
PCMADR[0]/NF_AD[0]/GPIO130 PWM0/GPIO71
K18
MODEL_OPT_0 ET_TXD[1]/GPIO61 TS1SYNC/GPIO102 V17
PCMADR[1]/NF_AD[1]/GPIO129 PWM1/GPIO72
K16 V17
PCMADR[1]/NF_AD[1]/GPIO129 PWM1/GPIO72
K16
NC_8 NC_23 NC_8 NC_23 W15 R16
PCMADR[2]/NF_AD[2]/GPIO127 PWM2/GPIO73
L18 R16
PCMADR[2]/NF_AD[2]/GPIO127 PWM2/GPIO73
L18
11 38 11 38 TS1VALID/GPIO101 AR180 MSTV_DEBUG U16
PCMADR[3]/NF_AD[3]/GPIO126 PWM3/GPIO74
L17 U16
PCMADR[3]/NF_AD[3]/GPIO126 PWM3/GPIO74
L17
H19 T17
PCMADR[4]/NF_AD[4]/GPIO104 PWM4/GPIO75
T17
PCMADR[4]/NF_AD[4]/GPIO104 PWM4/GPIO75
18 31 18 31 OPT V6 B2 W20
PCMDATA[7]/GPIO121
W20
PCMDATA[7]/GPIO121
20 29 20 29 D1 W16
PCM_RESET/GPIO134
W16
PCM_RESET/GPIO134
21 28 21 28 USB1_CTL ET_TX_EN/GPIO63
R180 K5 D8
NC_13 NC_18 NC_13 NC_18 10K MODEL_OPT_5 ET_RXD[0]/GPIO65 HWRESET SOC_RESET GND
22 27 22 27 EU R197 EU K4 E5
0 MODEL_OPT_6 ET_MDC/GPIO66 IRIN/GPIO5 IR
NC_14 NC_17 NC_14 NC_17 CI_DET CI_DET H6 G4
23 26 23 26 EU R178 22 USB1_OCD ET_MDIO/GPIO67 DDCA_CK/UART0_RX
/PCM_CD L5 G5
PCM_A[0-14] ET_RXD[1]/GPIO68 DDCA_DA/UART0_TX
NC_15 NC_16 NC_15 NC_16
24 25 24 25 1K OPT
PCM_A[0] U17 J18 OPT 2.2uF
PCMADR[0]/NF_AD[0]/GPIO130 PWM0/GPIO71
R130 10K C190
PCM_A[1] R18 K18 PWM0
R131
PCM_A[2] V17
PCMADR[1]/NF_AD[1]/GPIO129 PWM1/GPIO72
K16
BLU_CURRENT_CTL DIMMING
PCM_A[3] PCMADR[2]/NF_AD[2]/GPIO127 PWM2/GPIO73 PWM_DIM
NAND_FLASH_2G_TOSHIBA NAND_FLASH_1G_SS R16 L18
PCMADR[3]/NF_AD[3]/GPIO126 PWM3/GPIO74 1K R132
EAN61857001 PCM_A[4] U16 L17 PWM3
EAN60991002
IC102-*4 PCM_A[5] PCMADR[4]/NF_AD[4]/GPIO104 PWM4/GPIO75 PCM_5V_CTL +3.3V_Normal R156
IC102-*3 T17
K9F1G08U0D-SCB0 10K
TC58NVG1S3HTA00 PCM_A[6] PCMADR[5]/NF_AD[5]/GPIO106
W18 T8 PWM0
PCM_A[7] PCMADR[6]/NF_AD[6]/GPIO107 NF_ALE/GPIO146 PF_ALE R103
U20 T9 L101
PCM_A[8] PCMADR[7]/NF_AD[7]/GPIO108 NF_CEZ/GPIO142 /PF_CE0 BLM18PG121SN1D 10K
NC_1 NC_29 NC_1 NC_29 Y19 U9 PWM3
1 48 1 48 PCM_A[9] PCMADR[8]/GPIO113 NF_CLE/GPIO141 /PF_CE1
AA19 U11
NC_2 NC_28 NC_2 NC_28 PCM_A[10] PCMADR[9]/GPIO115 NF_RBZ/GPIO147 /F_RB
2 47 2 47 AA20 V9 R193 C119
PCM_A[11] PCMADR[10]/GPIO119 NF_REZ/GPIO144 /PF_OE 10K 0.1uF
NC_3 NC_27 NC_3 NC_27 W21 U10
3 46 3 46 PCM_A[12] PCMADR[11]/GPIO117 NF_WEZ/GPIO145 /PF_WE
V20 T10
NC_4 NC_26 NC_4 NC_26 PCM_A[13] PCMADR[12]/GPIO109 NF_WPZ/GPIO199 /PF_WP R196
4 45 4 45 Y17 0
PCM_A[14] PCMADR[13]/GPIO112 IF_AGC_MAIN
NC_5 I/O8 NC_5 I/O7 V18 W2
5 44 5 44 PCMADR[14]/GPIO111 IF_AGC
V19 W1 C120
NC_6 I/O7 NC_6 I/O6 PCM_D[0-7] /PCM_CD PCMCD_N/GPIO135 SIFM SIFM SIFM 0.047uF
6 43 6 43 W19 W3
/PCM_CE PCMCE_N/GPIO120 SIFP SIFP SIFP 25V
RY/BY I/O6 R/B I/O5 PCM_D[0] U18 V2
7 42 7 42 PCMDATA[0]/GPIO131 IM
PCM_D[1] V16 V1
RE I/O5 RE I/O4 PCMDATA[1]/GPIO132 IP
8 41 8 41 PCM_D[2] W17
PCMDATA[2]/GPIO133
CE NC_25 CE NC_25 PCM_D[3] Y20 AA2 R194 0 TUNER_IF_100_ohm
9 40 9 40 PCMDATA[3]/GPIO125 XIN IF_N_MSTAR R194-*1
PCM_D[4] R15 Y2 TUNER_IF_0_ohm IF OPT
NC_7 NC_24 NC_7 NC_24 PCMDATA[4]/GPIO124 XOUT C117 C121 100
10 39 10 39 PCM_D[5] AA18 0.1uF 100pF DTV_IF
PCMDATA[5]/GPIO123 R195 0
T15 IF_P_MSTAR TUNER_IF_100_ohm
NC_8 NC_23 NC_8 NC_23 PCM_D[6]
11 38 11 38 PCMDATA[6]/GPIO122 TUNER_IF_0_ohm IF
C118 C122 R195-*1
PCM_D[7] Y21 0.1uF 33pF TU_IF_CAP 100
VCC_1 VCC_2 VCC_1 VCC_2 PCMDATA[7]/GPIO121 TU_IF_CAP C124
12 37 12 37 W20 33pF
/PCM_IORD PCMIORD_N/GPIO116 For KR/US models
VSS_1 VSS_2 VSS_1 VSS_2 V21 Close to MSTAR
13 36 13 36 /PCM_IOWR PCMIOWR_N/GPIO114
Y18
NC_9 NC_22 NC_9 NC_22 /PCM_IRQA PCMIRQA_N/GPIO110
14 35 14 35 T16
/PCM_OE PCMOE_N/GPIO118
NC_10 NC_21 NC_10 NC_21 R17 X101 C113
15 34 15 34 /VBUS_EN /PCM_REG PCMREG_N/GPIO128 R187 24MHz
T18 1M X-TAL_1 GND_2
8pF
CLE NC_20 CLE NC_20 PCM_RST PCM_RESET/GPIO134 1 4
16 33 16 33 W16
/PCM_WAIT PCMWAIT_N/GPIO105 GND_1 X-TAL_2
ALE I/O4 ALE I/O3 U15 2 3
17 32 17 32 /PCM_WE PCMWE_N/GPIO198
WE I/O3 WE I/O2 C114
18 31 18 31
Close to MSTAR 8pF
WP I/O2 WP I/O1
19 30 19 30
NC_11 I/O1 NC_11 I/O0
20 29 20 29
NC_12 NC_19 NC_12 NC_19
21 28 21 28
NC_13 NC_18 NC_13 NC_18
22 27 22 27
NC_14 NC_17 NC_14 NC_17
23 26 23 26
NC_15 NC_16 NC_15 NC_16
24 25 24 25
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
MODEL OPTION +3.3V_Normal SOC_RESET STby 3.5V Normal Power 3.3V DDR3 1.5V VDDC 1.05V
+3.5V_ST AVDD_NODIE +3.3V_Normal VDD33 +1.5V_DDR AVDD_DDR1:55mA +1.10V_VDDC +1.10V_VDDC +1.10V_VDDC +1.10V_VDDC
+3.5V_ST AVDD_DDR0:55mA
L206 L204
MO_DVB_T2/C/S2
MO_S/W_EU/AJ
BLM18PG121SN1D
DDR_EXT:256
DDR_EXT:128
1K
1K
1K
1K
1K
1K
1K
1K
MO_S/W_AJ
MO_M120
MO_HD C200 C255 C259 C284 C204 C209 C235 C245 C266 C278 C248 C207 C254
4.7uF 0.1uF 0.1uF C228 C275 C277 C280 C283 C296 C210 C279
10V R217 C289 C286 C252 10uF 10uF 0.1uF 0.1uF 0.1uF 0.1uF 10uF 0.1uF 0.1uF 1uF 10uF 10uF 1uF 1uF 0.1uF 10uF 0.1uF 0.1uF
10uF 0.1uF 0.1uF 16V 16V 10V 10V 16V 16V 16V 16V 10V 16V 16V 10V
0 SOC_RESET 10V 10V 10V 10V 16V 10V 16V 16V
10V 16V 16V
R291
R222
R221
R206
R208
R211
R226
R290
DDR_EXT:256 or NON
AUD_LRCK BLM18PG121SN1D
MO_DUALSTREAM_NON
MO_S/W_NON_AJ
1K
1K
1K
1K
1K
1K
MO_DVB_T/C
MO_M120_NON
R224
R223
R207
R209
R227
MODEL OPTION
PIN NAME PIN NO. LOW HIGH M1A_256M_UO4 M1A_256M_UO4
IC101 IC101 M1A_128M_UO4
MODEL_OPT_0 J5 MO_FHD MO_HD LGE2134(256M) LGE2134(256M) IC101-*1
M1A_256M_AVS+
IC101-*2
LGE2133(128M) LGE2136(256M)
MODEL_OPT_1 H19 MO_S/W_NON_AJ MO_S/W_AJ
HDMI R4
AVDD_AU33 AUVRM
U3 U3
AUVRM AVDD_AU33
R4
G1 K3 VDD33 GND_18
AA10 H11 H11 AA10
G2 J1 R5 F15 GND_39
H13 H13
GND_39
F2 L6 R6 G8 GND_47
J9 J9
GND_47
T2 P14 H8 GND_71
P6 P6
GND_71
50V 50V VDDC_8 GND_35 GND_72 GND_72
EU 0 1 AUVAG L9 H9 GND_73
P7 P7
GND_73
AUDIO OUT C213 C220
VDD33 VDDP GND_36 GND_74
P9
P10
P9
P10
GND_74
GND_39 GND_80
R11 R11
GND_80
GND_41 GND_84
K7 K7
GND_84
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
TAIYO
R5606 CYNTEC
100 L5603-*1
AMP_RESET TDK 10uH
1/16W L5603
50V
L5601 C5609
R5607 10uH
4.7K 1000pF
BLM18PG121SN1D
22000pF
50V SPK_L+
C5610
+19V +19V_AMP
AUD_SCK
+19V_AMP
R5608
1/10W
L5600
3.3
UBW2012-121F R5614
5%
C5630
C5607 0.1uF
C5608 OPT C5620 50V 4.7K
10uF C5617 390pF
OPT 0.1uF C5615 50V
10V C5613 4.7uF
C5600 C5601 16V 10uF 0.1uF
25V 50V 50V
0.1uF 0.1uF 3216
C5627
50V 50V
0.47uF
50V
SPEAKER_L
C5621
[EP]GND
390pF
VDD_IO
GND_IO
PGND1A
PVDD1A
PVDD1B
50V TAIYO
CLK_I
RESET
BST1A
OUT1A
C5631 R5615
R5609
1/10W
L5605-*2 0.1uF
3.3
10.0uH 50V 4.7K
5%
AD
CYNTEC
L5605-*1
TDK 10uH
40
39
38
37
36
35
34
33
32
31
L5605
10uH
NC_1 1 30 OUT1B SPK_L-
VDD_PLL 2 29 PGND1B C5618
THERMAL 22000pF
NC_2 3 41 28 BST1B 50V
C5604
1uF GND 4 27 VDR1
C5605
10V
1uF NC_3 NC_5
10V 5 IC5600 26
DVDD 6 NTP7515 25 AGND
SDATA 7 24 VDR2
AUD_LRCH
WCK 8 23 BST2A C5624 C5625
AUD_LRCK
C5619 1uF 1uF
NC_4 9 22 PGND2A 22000pF 10V 10V
AR5601 50V
100 SDA 10 21 OUT2A
AMP_SDA 1/16W TAIYO
11
12
13
14
15
16
17
18
19
20
L5602-*2
10.0uH
CYNTEC
SCL
FAULT
MONITOR_0
MONITOR_1
MONITOR_2
BST2B
PGND2B
OUT2B
PVDD2B
PVDD2A
AMP_SCL
L5602-*1
C5602 C5603 TDK 10uH
33pF 33pF L5602
50V 50V 10uH
SPK_R+
R5610
1/10W
+19V_AMP
3.3
5%
C5628 R5612
TAIYO 0.1uF 4.7K
+3.3V_Normal
I2S_AMP
R5611
1/10W
C5611 10uH
0.1uF 4.7K
3.3
R5603 TDK
5%
10K 22000pF L5604 50V
50V 10uH
OPT SPK_R-
C5606
1000pF
50V
I2S_AMP
250A1-WR-H04M
WAFER-ANGLE
SPK_L+
4
SPK_L-
3
SPK_R+
2
SPK_R-
1
P5600
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Contents of Standard Repair Process
* First of all, Check whether there is SVC Bulletin in GCSC System for these model.
No. Error symptom (High category) Error symptom (Mid category) Page Remarks
1 No video/Normal audio 1
2 No video/No audio 2
3 Tuning fail, Picture broken/ Freezing 3, 4
A. Video error
4 Color error 5
Vertical/Horizontal bar, residual image, light spot,
5 6
external device color error
6 No power 7
B. Power error
7 Off when on, off while viewing, power auto on/off 8
8 No audio/Normal video 9
C. Audio error
9 Wrecked audio/discontinuation/noise 10
10 Remote control & Local switch checking 11
D. Function error
11 External device recognition error 12
12 E. Noise Circuit noise, mechanical noise 13
13 F. Exterior error Exterior defect 14
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
First of all, Check whether all of cables between board is inserted properly or not.
(Main B/D ↔ Adaptor, LVDS Cable, Speaker Cable, IR B/D Cable…)
☞A1 ☞A4
Y Y Y
No video Normal Check Back Light Check LVDS 12 V Normal Replace T-con B/D
Normal audio On with naked eye On of Main B/D or Module
Audio Voltage
N N N
☞A2
Move to Check Main B/D to LED Back light Voltage Replace Main
No video/No audio B/D or Repair parts
Y
Normal Replace Module
Voltage
Replace Main
B/D or Repair parts
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
☞A13
No video / Check voltage 19V Normal Y Replace Main
No audio of Adaptor Voltage B/D or Repair parts
Replace Adaptor
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
☞ A6
Check RF Cable
Normal Y Check SVC N Check Normal Y
Connection End
1. Reconnection Picture S/W Version Bulletin Tuner soldering Picture
2. Install Booster
N Y N
Y
Normal N
Picture
End
Y
End
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
N Normal N
Normal
Picture Picture
Y Y
End End
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
☞ A8 / A9
☞A7 Check and
replace Link Y Y
Check color by input Y
Color Cable Color Color
- External Input Replace Main B/D Replace module
error (LVDS) and error error
(COMPONENT/AV/HDMI)
contact
N N N
condition
Request repair
for external
device/cable
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
S/W Upgrade
End Request repair for
external device
Normal N
Screen
End
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
☞A11
DC Power on N
Check Power Y Normal Replace
by pressing Power Key
Power LED LED On Operation Main B/D
On Remote control
Stand-By : Red N Y
Power Y
LED On
※
N Y
☞A16
Normal
Check ST-BY 3.5V
Voltage
Replace Adaptor or
Replace Main B/D
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
☞A14
N Y CPU Y
Check outlet Adaptor Check Power Off
Error Abnorm Replace Main B/D Normal End
or A/C cord DC Out Mode
al
Y N
N
Abnorm
al1 Replace Adaptor
☞A13
Fix A/C cord & Outlet Replace
Adaptor (If Power Off mode
is not displayed) Normal Y
Replace Main B/D
Check Adaptor Voltage
voltage
N
Replace Adaptor
* Please refer to the all cases which Status Power off List Explanation
can be displayed on power off mode. "POWEROFF_REMOTEKEY" Power off by REMOTE CONTROL
"POWEROFF_OFFTIMER" Power off by OFF TIMER
"POWEROFF_SLEEPTIMER" Power off by SLEEP TIMER
"POWEROFF_INSTOP" Power off by INSTOP KEY
"POWEROFF_AUTOOFF" Power off by AUTO OFF
Normal "POWEROFF_ONTIMER" Power off by ON TIMER
"POWEROFF_RS232C" Power off by RS232C
"POWEROFF_RESREC" Power off by Reservated Record
"POWEROFF_RECEND" Power off by End of Recording
"POWEROFF_SWDOWN" Power off by S/W Download
"POWEROFF_UNKNOWN" Power off by unknown status except listed case
"POWEROFF_ABNORMAL1" Power off by abnormal status except CPU trouble
Abnormal
"POWEROFF_CPUABNORMAL" Power off by CPU Abnormal
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
☞A15
Check user
Y
No audio Connection Connec Replace Speaker
Screen normal from Main tion or Main B/D
Speaker Cable
N
Normal N
Audio
End
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
Wrecked Audio/ Y
Normal
Discontinuation/Noise Replace Main B/D
Voltage
only for D-TV
N
Wrecked Audio/
Discontinuation/Noise Replace Adaptor
only for Analog
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
Replace
Main B/D
☞A16 Y
☞A16 ☞A16
Y Check & Repair N
Check R/C itself Normal Normal Check 3.5V Normal Y Check IR Normal
Cable connection
Operation Operating Operating On Main B/D Voltage Output signal Signal
Connector solder
N Y N N
☞A13
End Check Voltage 19V of Adaptor Replace
Check R/C Operating Check & Replace IR B/D
When turn off light Baterry of R/C
in room
If R/C operate,
Explain the customer Y
Normal
cause is interference End
Operating
from light in room.
Replace R/C
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
Check technical
Y External Input
Check input Signal information Technical N
and Component Replace Main B/D
signal Input - Fix information information
Recognition error
- S/W Version
N Y
Fix in
Check and fix accordance HDMI
external device/cable with technical Recognition
information error
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
※ Mechanical noise is a natural ※ When the nose is severe, replace the module
phenomenon and apply the 1st level (For models with fix information, upgrade the S/W or
description. provide the description)
When the customer does not agree, apply or
the process by stage. ※ If there is a “Tak Tak” noise from the cabinet, refer
※ Describe the basis of the description in to the KMS fix information and then proceed as
“Part related to nose” in the Owner’s Manual. shown in the solution manual
(For models without any fix information, provide the
description)
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
Cabinet
Replace cabinet
damage
Remote
Control Replace remote control
damage
Stand
Replace stand
damage
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Contents of Standard Repair Process Detail Technical Manual
* First of all, Check whether there is SVC Bulletin in GCSC System for these model.
No. Error symptom Content Page Remarks
1 Check LCD back light with naked eye A1
2 LED driver B+ measuring method A2
A. Video error_ No video/Normal audio
3 Check White Balance value A3
4 Power voltage measuring method A4
6 TUNER input signal strength checking method A5
A. Video error_ No video/Video lag/stop
7 TV Version checking method A6
9 Connection diagram A7
10 A8
A. Video error_Color error Check Link Cable (LVDS) reconnection condition
11 A9
13 Connection diagram A8
A. Video error_Vertical/Horizontal bar, A8
14 Check Link Cable (LVDS) reconnection condition
residual image, light spot A9
15 Adjustment Test pattern - ADJ Key A10
16 Exchange T-Con Board (1) A-1/5
17 Exchange T-Con Board (2) A-2/5
<Appendix>
18 Defected Type caused by T-Con/ Inverter/ Exchange LED driver Board (PSU) A-3/5
Module
19 Exchange Module itself (1) A-4/5
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Contents of Standard Repair Process Detail Technical Manual
* First of all, Check whether there is SVC Bulletin in GCSC System for these model.
No. Error symptom Content Page Remarks
21 Check front display LED A11
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process Detail Technical Manual
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process Detail Technical Manual
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process Detail Technical Manual
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process Detail Technical Manual
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process Detail Technical Manual
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process Detail Technical Manual
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process Detail Technical Manual
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process Detail Technical Manual
Error Symptom A. Video Error, Color Error Established date 2015.04.17 A8/
Content Check and replace Link Cable(LVDS) and contact condition Revised date A9
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process Detail Technical Manual
Checking item : 1. Defective pixel 2. Residual image 3. MODULE error (ADD-BAR,SCAN BAR..)
4.Video error (Classification of MODULE or Main-B/D)
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Appendix : Exchange T-Con Board (1)
Solder defect, CNT Broken Solder defect, CNT Broken Solder defect, CNT Broken
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Appendix : Exchange T-Con Board (2)
Solder defect, Short/Crack Fuse Open, Abnormal power section Abnormal Display
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Appendix : Exchange the Module (1)
Un-repairable Cases
In this case please exchange the module.
Crosstalk Crosstalk
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Appendix : Exchange the Module (2)
Un-repairable Cases
In this case please exchange the module.
Horizontal Block
Gate TAB IC Defect
Gate TAB IC Defect
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process Detail Technical Manual
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process Detail Technical Manual
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process Detail Technical Manual
Error Symptom B. Power Error, Off when on, off whiling viewing Established date 2015.04.17
A14
Content Power off Mode checking method Revised date
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process Detail Technical Manual
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process Detail Technical Manual
Error Symptom D. Function Error, No Response in remote controller, Key error Established date 2015.04.17
A16
Content Remote controller operation checking method Revised date
P4600
1 KEY2
③ 2 3.5V_ST
3 GND
4 LED_R/BUZZ
④ 5 IR
6 GND
②
① < Sub Ass’y>
4. When checking the Pre-Amp when the power is in ON condition, it is normal when the Analog
Tester needle moves slowly, and defective when it does not move at all.
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes