Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
COMPANION FLANGES
J300P-1
NOVEMBER 2012
Supersedes
Section 1, Dated
November 2007
Follow us @ Spicerparts
www.Spicerparts.com
HOW TO USE THIS CATALOG J300P-1
To identify any splined companion flange, there are ten pieces of required information:
1. Center Hole type (Splined, Round or Tapered hole)
2. Spline size and tooth count
3. Pilot diameter and type (Male / Female)
4. Bolt circle diameter
5. Bolt hole diameter and if the hole is drilled or tapped (drilled-D or tapped-T)
6. Number of bolt holes
7. Ground hub diameter (where applicable)
8. Brake drum pilot diameter
9. Length of through hole
10. Flange face to end of hub
Example: to find a companion flange with a 2.143-41 involute splined hole, a 7.750 female pilot
that includes twelve bolts:
1. Find the Splined Hole section of this catalog;
2. Find the 2.143-41 Involute Spline sub-heading;
3. Find the Female Pilot diameter of 7.750
4. Find the Bolt circle diameter of 7.250
5. Find the Drilled Bolt hole diameter of .440
6. Find a Number of bolt holes of 12
7. Find the Ground hub diameter of 2.939
8. Find the Brake drum pilot diameter (not applicable in this example)
9. Find the Length of through hole of 2.495
10. Find the Flange face to end of hub of 3.500
Locate the part number that matches the dimension of your part: example 6.5-1-2941
Be sure to read any notes that are provided.
J300P-1
COMPANION
1
FLANGES
Spline Hole
D C B Bolt Hole E F G F Companion
Spline Pilot Brake Flange i Flange Companion
g
Hole Diameter Bolt Diameter Drum Ground Length Face Assembly Slinger Flange
u
Major F-Female Circle D-Drilled # of Pilot Hub Thru to End r (includes slinger Part Part Series
Diameter M-Male Diameter T-Tapped Holes Diameter Diameter Hole of Hub e when listed) Number Number
J300P-1
1
COMPANION FLANGES 2
Circular Type - Straight Round Hole
D K C
Bolt E F
Pilot Hole
Flange Companion
Diameter Diameter
Face Flange
Bore Keyway F-Female D-Drilled
Hub to End Part
3 Diameter Width M-Male Figure T-Tapped
Diameter of Hub Number
1610 SERIES (Continued) A-6.875 B-6.125 DIA. (8 HOLES)
2.500 .625 6.625 F 1 .375 D 5.250 3.500 5-1-873-6
2.750 .625 6.625 F 1 .375 D 5.250 3.500 5-1-873-7
2.938 .750 6.625 F 1 .375 D 5.250 3.500 5-1-873-8
3.000 .750 6.625 F 1 .375 D 5.250 3.500 5-1-873-9
3.125 — 6.625 F 2 .375-24 T 6.875 5.000 5-1-883
3.500 .875 6.625 F 2 .375-24 T 6.875 5.000 5-1-883-1
4 5 6 7 8 Part
Number
Footnotes for parts and assemblies that are discontinued, will be discontinued upon depletion of
stock, or not sold separately, are indicated by a symbol next to the part number. Match the symbol
to the appropriate status at the bottom of the page. All other footnotes are located immediately
below the yoke dimensional data.
Important Notice: The data listed herein is correct to the best of our knowledge and belief; having
been compiled from reliable and official sources of information. However, WE CANNOT ASSUME
ANY RESPONSIBILITY for possible error.
• Part is discontinued Part is available until supply is exhausted © Not sold separately
• Part is discontinued Part is available until supply is exhausted © Not sold separately
• Part is discontinued Part is available until supply is exhausted © Not sold separately
2.032-10 Spline
2.032 7.750-F 7.250 .438D 12 — 2.750 2.000 2.688 4 — — 6.5-1-2421• 1810
2.114-32 Involute Spline
2.114 .000-F 5.118 .512 D 4 — 3.000 2.250 3.500 1 — — 5002710
5002710 will be replaced by 5-1-02710 when supply is exhausted; Serrated face flange
2.114 .000-F 5.118 .512 D 4 — 3.000 2.250 3.500 1 — — 5-1-02710
Serrated face flange
2.114 5.312-M 6.125 .385D 8 — 3.000 2.250 2.844 3 5-1-6731X• 232200 5-1-6721© 1610
.424 deep counterbore at hub end
2.114 6.625-F 6.125 .375D 8 — 3.000 2.245 2.844 3 5-1-6701X• 232200 5-1-6691• 1610
.424 deep counterbore at hub end
2.143-41 Involute Spline
2.143 7.750-F 7.250 .440D 12 — 2.939 2.495 3.500 4 — — 6.5-1-2941§ 1810
2.149-16 Spline
2.149 6.625-F 6.125 .385D 8 — 2.938 3.000 3.750 3 — — 5-1-2551• 1610
.380 deep counterbore at hub end
2.225-6 Spline
2.225 6.625-F 6.125 .375D 8 — 3.000 3.250 3.875 3 — — 5-1-2541 1610
2.225 7.750-F 7.250 .375D 8 — 3.000 3.250 3.750 3 — — 6-1-1731 1710
2.225 7.750-F 7.250 .375D 8 — 3.000 3.250 4.469 3 — — 6-1-1481• 1710
2.225 7.750-F 7.250 .438D 12 — 3.000 3.250 3.750 4 — — 6.5-1-481 1810
2.250-10 Spline
2.250 6.625-F 6.125 .375D 8 — 3.500 3.000 3.625 3 — — 5-1-6331§ 1610
2.250 7.750-F 7.250 .375D 8 — 3.000 3.000 3.750 3 — — 6-1-1421§ 1710
.250 deep counterbore at hub end
• Part is discontinued Part is available until supply is exhausted © Not sold separately
• Part is discontinued Part is available until supply is exhausted © Not sold separately
• Part is discontinued Part is available until supply is exhausted © Not sold separately
Figure 1 Figure 2
D K C
Bolt E F
Pilot Hole
Flange Companion
Diameter Diameter
Face Flange
Bore Keyway F-Female D-Drilled
Hub to End Part
Diameter Width M-Male Figure T-Tapped
Diameter of Hub Number
1310 SERIES A-3.875 B-3.125 DIA. (4 HOLES)
.750 — 2.375-F 1 .375-D 2.438 2.000 2-1-1313
Rough bore - without keyway
1.000 .250 2.375-F 1 .375-D 2.438 2.000 2-1-1313-1
1.250 .250 2.375-F 1 .375-D 2.438 2.000 2-1-1313-3
1.250 .310 2.375-M 1 —-D 2.250 2.000 2-1-1353-5
1.250 .312 2.375-F 1 .375-D 2.438 2.000 2-1-1313-4
1.375 .312 2.375-F 1 .375-D 2.438 2.000 2-1-1313-5
1.438 .375 2.375-F 1 .375-D 2.438 2.000 2-1-1313-7
1.500 .375 2.375-F 1 .375-D 2.438 2.000 2-1-1313-8
1.625 .375 2.375-F 1 .375-D 2.438 2.000 2-1-1313-9
1.750 .375 2.375-F 2 .375-24-T 3.875 2.500 2-1-1323-1
1.875 .500 2.375-F 2 .375-24-T 3.875 2.500 2-1-1323-3
1350 SERIES A-4.562 B-3.750 DIA. (4 HOLES)
1.000 — 2.750-F 1 .438-D 2.875 2.000 3-1-1013
Rough bore - without keyway
1.000 — 2.750-F 1 .440-D 2.875 3.440 3-1-303
Rough bore - without keyway
1.000 .250 2.750-F 1 .438-D 2.875 2.000 3-1-1013-1
1.125 .250 2.750-F 1 .438-D 2.875 2.000 3-1-1013-2
1.250 .250 2.750-F 1 .438-D 2.875 2.000 3-1-1013-3
1.250 .312 2.750-F 1 .438-D 2.875 2.000 3-1-1013-4
1.375 .312 2.750-F 1 .438-D 2.875 2.000 3-1-1013-5
1.375 .375 2.750-F 1 .438-D 2.875 2.000 3-1-1013-6
1.438 .375 2.750-F 1 .438-D 2.875 2.000 3-1-1013-7
1.500 .375 2.750-F 1 .438-D 2.875 2.000 3-1-1013-8
1.625 .375 2.750-F 1 .438-D 2.875 2.000 3-1-1013-9
1.750 — 2.750-F 2 .438-20-T 4.562 3.000 3-1-1023•
Rough bore - without keyway
1.750 .375 2.750-F 1 .438-D 2.875 2.000 3-1-1013-10
1.750 .377 2.750-F 1 .440-D 2.875 3.440 3-1-303-7
1.875 .375 2.750-F 1 .438-D 2.875 2.000 3-1-1013-11
1.875 .500 2.750-F 1 .438-D 2.875 2.000 3-1-1013-12
2.000 .500 2.750-F 2 .438-20-T 4.562 3.000 3-1-1023-1
2.125 .500 2.750-F 2 .438-20-T 4.562 3.000 3-1-1023-2
2.250 .500 2.750-F 2 .438-20-T 4.562 3.000 3-1-1023-10•
• Part is discontinued Part is available until supply is exhausted © Not sold separately
• Part is discontinued Part is available until supply is exhausted © Not sold separately
• Part is discontinued Part is available until supply is exhausted © Not sold separately
• Part is discontinued Part is available until supply is exhausted © Not sold separately
• Part is discontinued Part is available until supply is exhausted © Not sold separately
C D - Taper Hole E F G
Pilot Flange Brake Companion
Diameter Width Ground Length Face Drum Flange
M-Male Bore of Hub Thru to End Pilot Part
F-Female Diameter Keyway Diameter Hole of Hub Diameter Number
1610 SERIES A-6.875 B-6.125 DIA. (8 HOLES)
1.750 Spline
6.625-F 1.750 .438 2.750 2.250 2.938 — 5-1-1154
2.000 Spline
6.625-F 2.000 .500 3.250 3.000 3.625 — 5-1-1924
1650/1710 SERIES A-CIRCULAR 8.000 B-7.250 DIA. (8 HOLES .325 DIA)
2.000 Spline
7.750-F 2.000 .500 3.250 3.000 3.688 — 6-1-1144§
• Part is discontinued Part is available until supply is exhausted © Not sold separately
C D - Taper Hole E F G
Pilot Flange Brake Companion
Diameter Width Ground Length Face Drum Flange
M-Male Bore of Hub Thru to End Pilot Part
F-Female Diameter Keyway Diameter Hole of Hub Diameter Number
1310 SERIES A-3.875 B-3.125 DIA. (4 HOLES)
1.375 Spline
2.375-F 1.375 .375 2.250 2.000 2.625 — 2-1-634
1.500 Spline
2.375-F 1.500 .375 2.375 2.000 2.625 — 2-1-684•
1350/1 SERIES A=4.625 B=3.750 (4 HOLES)
1.250 Spline
2.750-F 1.250 .312 2.125 1.500 2.437 3.000 3-1-604
1.375 Spline
2.750-F 1.375 .375 2.250 2.000 2.625 — 3-1-584§
• Part is discontinued Part is available until supply is exhausted © Not sold separately
21
NOTES J300P-1
22
J300P-1 NOTES
23
Follow us @ Spicerparts
Dana Holding Corporation
Aftermarket Group
PO Box 321
Toledo, Ohio 43697-0321
www.spicerparts.com
www.Spicerparts.com
J300P-1 © Dana Limited 2012.
11/12 All rights reserved.
Printed in U.S.A