Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
TECHNICAL SERVICE
MANUAL
Prestigio P170T TECHNICAL SERVICE MANUAL
1 FORWORD
This document defines design and performance requirements for Prestigio 17.0" On Screen Display
Color TFT LCD monitor P170T. It is capable of displaying maximum 1,280 horizontal dots and 1024
vertical lines resolution image.
It also offers Power Management and DDC2B features according to VESA proposal.
2 GENERAL DESCRIPTION
The monitor described in the followings is based on a multi- scanning, digital control display, 17.0
inches diagonal. The monitor is intended to be a finished product, basically a display device mounted
inside a plastic enclosure which will provide the aesthetic, ergonomic and safety requirements.
2
TECHNICAL SERVICE MANUAL Prestigio P170T
Control Description
Front View
LED Indicator
Power Switch
3
Prestigio P170T TECHNICAL SERVICE MANUAL
ELECTRICAL CHARACTERISTICS
The input signal shall be applied to the display device through a signal cable, which must be
intended as part of the monitor.
A signal connector shall be a shielded 15pin D- Sub connector and signal cable shall be Black or
White, 1.50¡ 0.05 meter long.
The reference video controller (the device used for adjustment and test) will guarantee the
performances described below (measured on the output connector).
700mV
2.74mV
Blanking
This monitor shall not be demaged by improper sync timing and pulse duration, absence of sync, or
abnormal input amplitude (video and/or sync too large too small).
4
TECHNICAL SERVICE MANUAL Prestigio P170T
3.1.3 Timing
This monitor shall be capable of displaying following video timing chart.
* Timing Chart
5
Prestigio P170T TECHNICAL SERVICE MANUAL
6
TECHNICAL SERVICE MANUAL Prestigio P170T
- Preset-mode table
The timing shown in the following table will be factory preset for display.
Horizontal Pixel 720 640 640 800 800 800 800 832 1024 1024 1024 1152 1280 1280
Pixel Clock MHz 28.322 25.175 31.500 36.000 40.000 49.500 50.000 57.283 65.000 75.000 78.750 108.00 108.00 135.00
Frequency kHz 31.469 31.469 37.500 35.156 37.879 46.875 48.077 49.725 48.363 56.476 60.023 67.500 63.981 79.976
Period (T1) §` 31.777 31.778 26.667 28.444 26.400 21.333 20.800 20.111 20.677 17.707 16.660 14.815 15.630 12.504
Active (T4) §` 25.422 25.422 20.317 22.222 20.000 16.162 16.000 14.524 15.754 13.653 13.003 10.667 11.852 9.481
Sync Width (T2) §` 3.813 3.813 2.032 2.000 3.200 1.616 2.400 1.117 2.092 1.813 1.219 1.185 1.037 1.067
Back Porch (T3) §` 1.907 1.907 3.810 3.556 2.200 3.232 1.280 3.910 2.462 1.920 2.235 2.370 2.296 1.837
Front Porch (T5) §` 0.636 0.636 0.508 0.667 1.000 0.323 1.120 0.558 0.369 0.320 0.203 0.593 0.444 0.119
Vertical Lines 400 480 480 600 600 600 600 624 768 768 768 864 1024 1024
Frequency Hz 70.087 59.940 75.000 56.250 60.317 75.000 72.188 74.55 60.004 70.069 75.029 75.000 60.020 75.025
Period (T1) §´ 14.268 16.683 13.333 17.778 16.579 13.333 13.853 13.414 16.666 14.272 13.328 13.333 16.661 13.329
Active (T4) §´ 12.711 15.253 12.800 17.067 15.840 12.800 12.480 12.549 15.880 13.599 12.795 12.800 16.005 12.804
Sync Width (T2) §´ 0.064 0.064 0.080 0.057 0.106 0.064 0.125 0.060 0.124 0.106 0.050 0.044 0.047 0.038
Back Porch (T3) §´ 1.112 1.048 0.427 0.626 0.607 0.448 0.478 0.784 0.600 0.513 0.466 0.474 0.594 0.475
Front Porch (T5) §´ 0.381 0.318 0.027 0.028 0.026 0.021 0.770 0.020 0.062 0.053 0.017 0.015 0.016 0.013
Interlaced Y /N N N N N N N N N N N N N N N
H - - - + + + + - - - + + + +
Sync Polarity
V + - - + + + + - - - + + + +
Table 3-02. Preset-Timings
7
Prestigio P170T TECHNICAL SERVICE MANUAL
3.1.6 Brightness
Definitions :
The measurement shall be executed after warming-up time during 30 minutes in a dark
room ( Ambient luminance ≤ 10 lux, temperature 25 ¡C)
O
8
TECHNICAL SERVICE MANUAL Prestigio P170T
9
Prestigio P170T TECHNICAL SERVICE MANUAL
3.5 TV Input
3.5.1 NTSC
iAPPLICATION
-Receiving System : ( NTSC STANDARD SYSTEM )
-Channel VHF Low BAND : 2(55.25MHz) ~ H(163.25MHz)
High BAND : I(169.25MHz) ~ W+26(451.25MHz)
UHF BAND : W+27(457.25MHz) ~ 78(855.25MHz)
-Intermediate Frequeny PIF : (45.75)MHz
CIF : (44.83)MHz
SIF : (41.25)MHz
-Input Impedance : UHF/VHF Terminal (75) Y , Unbalanced
-Output Impedance : ViDEO : C.V.B.S
AUDIO : -
IF : SECOND IF
-Band Chang – Over System : (PLL Control System)
-Tuning System : (Electronic Tuning System With PLL)
10
TECHNICAL SERVICE MANUAL Prestigio P170T
3.5.2 PAL
- APPLICATIONS
-Receiving System : ( PAL B/G+I+D/K + SECAM L/L’ STANDARD SYSTEM )
- Channel VHF Low BAND : E2(48.25MHz) ~ S10(168.25MHz)
High BAND : E5(175.25MHz) ~ S41(463.25MHz)
UHF BAND : E21(471.25MHz) ~ E69(855.25MHz)
-Intermediate Frequency PIF : PAL B/G/I/D/K, SECAM L 38.90MHz
SECAM L’ 33.90MHz
CIF : PAL B/G/I/D/K, SECAM L 34.47MHz
SECAM L’ 38.15 / 38.3MHz
SIF : PAL B/G 33.4MHz, PAL I 32.9MHz
PAL D/K, SECAM L 32.4MHz
SECAM L’ 40.4MHz
-Input Impedance : UHF/VHF Terminal (75)Y , Unbalanced
-Band Change – Over System : PLL Control System
-Tuning System : Electronic Tuning System With PLL
-Applicable Standard
Complies with European Regulations on Radiation, Signal handling and Immunity
CENELEC EN55020, EN55013
11
Prestigio P170T TECHNICAL SERVICE MANUAL
3.6.2 Speaker
- Micro Loudspeaker Spec.
Normal impedance 8 ± 15% at 1.0V 1.5KHz
Resonance Freq. 550Hz ± 110Hz at 1.0V
Freq. Range fo ~ 20KHz
Power Rating. Normal 1.0W /Peak 2.0W
3.6.3 Audio System Specification
· Audio Amplifier Vcc=12V
· Audio Signal Input : < -10.0dB (Vrms=300mV) Max
· Audio Output : 1.0W Max (1ch) @THD=5% (Maximum Input)
This display device shall maintain the specified performances in the range described below :
Frequency 50 / 60Hz
Voltage 90 ~ 264Vac RMS
Power On/Off time > 0.3 sec
12
TECHNICAL SERVICE MANUAL Prestigio P170T
On : Normal Operation
Off : Non Operation
3.8.3 TV Signal
There is no definition of power management for TV signals.
13
Prestigio P170T TECHNICAL SERVICE MANUAL
4 USER INTERFACE
4.1 User Controls
This display device shall have following On- Screen Display controls.
14
TECHNICAL SERVICE MANUAL Prestigio P170T
4.2.3 Miscellaneous
- Recall
Return to Factory adjustment condition.
Change four parameters -> Brightness, Contrast, Color, Audio
- OSD Timer and OSD Position
By this menu, a user can control a location of OSD on screen and the display time of OSD
menu. OSD Position is showed and selected by pressing the select button.
4.2.4 Audio
- Volume : By this menu, a user can control the audio volume.
- Sound off : By this menu, a user can control the audio on/off.
- Treble : By this menu, a user can control the treble gain(¡ 14dB,15step).
- Base : By this menu, a user can control the base gain(¡ 14dB,15step).
15
Prestigio P170T TECHNICAL SERVICE MANUAL
4.2.6 Language
By pressing LANGUAGE in main menu, a user can select one of 10 languages, English,
Spanish, German, French, Italian, Swedish, Finnish, Danish, Portuguese, Dutch.
To select a language must press Select button.
4.2.9 Source
This menu used to choose the desired input signal source.
There are four available signal source.
- Analog RGB : 15 pin D-sub, analog signal
- S-Video : MINI DIN, Separate video signal
- Composite : RCA Jack, Composite video signal
- TV : NTSC, PAL
16
TECHNICAL SERVICE MANUAL Prestigio P170T
4.3.3 Miscellangeous
- Recall
Return to Factory adjustment condition.
Change four parameters -> Brightness, Contrast, Image, Audio
- OSD Timer and OSD Position
By this menu, a user can control a location of OSD on screen and the display time of OSD
menu. OSD Position is showed and selected by pressing the select button.
4.3.4 Audio
- Volume : By this menu, a user can control the audio volume.
- Sound off : By this menu, a user can control the audio on/off.
- Treble : By this menu, a user can control the treble gain(¡ 14dB,15step).
- Base : By this menu, a user can control the base gain(¡ 14dB,15step).
4.3.5 Language
By pressing LANGUAGE in main menu, a user can select one of 10 languages, English,
Spanish, German, French, Italian, Swedish, Finnish, Danish, Portuguese, Dutch.
To select a language must press Select button.
4.3.6 (TV)
- CH Searching : By selecting country on the screen, this program enable to search for the
channels automatically.
If cable(Air/CATV) is disconnected or inappropriate country is selected,
it may be operated improperly.
- CH Edit : By this menu, a user can edit the TV channel (add channel / delete channel).
- CH Fine Tune : By this menu, a user can tune the TV channel finely.
- TV Input : By this menu, a user can select the TV channel (Air / Cable).
4.3.7 Source
This menu used to choose the desired input signal source.
There are four available signal source.
- Analog RGB : 15 pin D-sub, analog signal
- S-Video : MINI DIN, Separate video signal
- Composite : RCA Jack, Composite video signal
- TV : NTSC, PAL
17
Prestigio P170T TECHNICAL SERVICE MANUAL
18
TECHNICAL SERVICE MANUAL Prestigio P170T
- POWER
By this key, a user can turn on (off) the main Power.
- INPUT SOURCE
By this key, a user can change Input source sequentially. (PC->S-VIDEO->VIDEO->TV->PC)
- Numeric
By this key, a user can select Channel directly.(TV Mode only)
- DISPLAY
By this key, a user can know about current state.(PC, S-VIDEO, VIDEO, TV – CH)
- PRE.CH
By this key, a user can move previous Channel.(TV Mode only)
- MUTE
By this key, a user can control the audio on/off. (4.2.4 & 4.3.4)
- EXIT
By this key, a user can exit all kinds of OSD menu.
- MENU
By this key, a user can activate OSD menu.
When OSD menu is activated, this key operate like select button.
- CH ( + / - )
By this key, a user can change TV Channel sequentially.(TV Mode only)
When OSD menu is activated, this key move selected item up or down.
- VOL ( + / - )
By this key, a user can control the audio volume.(4.2.4 & 4.3.4)
When OSD menu is activated, this key act like button or button.
- AUTO
If a user press this key, AUTO Adjust function(4.2.5) executing.(PC Mode only)
- CH SEARCH
If a user press this key, CH Searching function(4.3.6) executing.(TV Mode only)
19
L17T Technical Service Manual
Prestigio P170T TECHNICAL SERVICE MANUAL
20
--19--
TECHNICAL SERVICE MANUAL Prestigio P170T
1280X1024
V:60.0/H:63.9
21
L17T Technical Service Manual
Prestigio P170T TECHNICAL SERVICE MANUAL
OSD Adjustments
he OSD adjustments available to you are listed below.
BrigHtness
Adjust the brightness of the screen.
Contrast
Adjust the contrast of the screen.
Color control
Color temperature affects the tint of the image. With lower color
temperatures the image turns reddish and with higher temperatures
bluish.
There are three color settings available: Mode 1(a cool white), Mode 2(a warm
white) or USER. With the USER setting you can set individual values for red,
green and blue.
MISCELLANEOUS
Recall
Recall the saved color data.
OSD TIMER
You can set the displayed time of OSD Menu window on the screen by using
this adjustment.
OSD Position
Adjust the OSD menu's horizontal or vertical position on the screen.
AUDIO
VOLUME
Adjust the audio volume level.
SOUND OFF
This menu is used to choose audio on or off.
TREBLE
Emphasize high frequency audio.
BASE
Emphasize low frequency audio.
AUTO ADJUST
You can adjust the shape of screen automatically at the full screen
pattern.
Language
You can select the language in which adjustment menus are displayed.
The following languages are available : English, French, German, Italian,
Spanish, Swedish, Finnish, Danish, Portuguese and Dutch.
22
--21--
TECHNICAL SERVICE MANUAL Prestigio P170T
H/V. POSITION
H POSITION
Adjusts the horizontal position of the entire screen image.
V POSITION
Adjusts the vertical position of the entire screen image.
CLOCK PHASE
PHASE
Adjust the noise of the screen image.
CLOCK
Adjust the horizontal size of the entire screen image.
SOURCE
No function. (Only supportable by the optional appliance.)
23
Prestigio P170T TECHNICAL SERVICE MANUAL
24
TECHNICAL SERVICE MANUAL Prestigio P170T
OSD Adjustments
Brightness
Adjust the brightness of the screen.
Contrast
Adjust the contrast of the screen.
Image Adjust
Saturation
Adjust the saturation of the video image.
Tint
Adjust the Tint of the video image.
Sharpness
Adjust the sharpness and softness of the video image.
Miscellaneous
Recall
Recall the saved color data.
OSD Timer
You can set the displayed time of OSD Menu window on the screen by
using this adjustment.
OSD Position
Adjust the OSD menu's horizontal or vertical position on the screen.
Audio
Volume
Adjust the audio volume level.
Sound off
This menu is used the choose audio on or off.
Treble
Emphasize high frequency audio.
Base
Emphasize low frequency audio.
25
Prestigio P170T TECHNICAL SERVICE MANUAL
Language
You can select the language in which adjustment menus are displayed. The
following languages are available : English, French, German, Italian, Spanish,
Swedish, Finnish, Danish, Portuguese and Dutch.
Source
This menu is used to choose the desired input signal source.
There are four signal sources available :
- Analog RGB : 15 pin D-sub, Analog signal
- S-video : MINI DIN, Separate video signal
- Composite Video : RCA Jack, Composite video signal
- TV : Antenna or CATV signal
TV
Ch Searching
By selecting country on the screen, this program enabls to seach for the
channels automatically.
! If cable(Air/CATV) is disconnected or inappropriate country is selected, It
may be operated improperly.
Ch Edit
To add a newly found channel or remove an existing channel.
Ch Fine Tune
To make the video image as clear as posible.
TV Input
Select a channel system : Air or Cable.
26
TECHNICAL SERVICE MANUAL Prestigio P170T
Getting Fine Picture
Step 1. At first Display, a full screen, such as, Window's background or "H" character should
be achieved by using Editor (ex: Notepad. exe)
Step 2. Adjust the screen to the center of the Display(LCD), by using the top and bottom
display controls. (i.e.Using V-Position Adjust menu)
Step 3. Adjust the screen to the center of the Display(LCD), by using the right and left
display controls. (i.e.Using Clock and H-Position adjust menu)
Step 4. Adjust the Clock-phase until the "H" Character displays clear.
Step 5. Using the Contrast. Brightness, and Color Control menu, set the color to your
preference.
Step 6. When you finish the adjustment, you can save your settings by pressing on the menu
until the OSD screen has disappeared.
Factory Setting & EEPROM Initialization Method
Factory Setting Method
- Connect the signal cable and power cable to the LCD monitor.
- Press Power switch with pressed MENU key.(Menu key + Power key).
- Then, a User can change the factory setting value in OSD menu.
- Save changed value and Turn off the power s/w.
- Turn on the power, adjust the screen.
27
L17T Technical Service Manual
Prestigio P170T TECHNICAL SERVICE MANUAL
Specification
LCD 17"viewable, Diagonal, A-Si TFT
Pixel pitch 0.264 x 0.264mm
Brightness 250cd/m2
Response Time 16msec
Display area 337.920 x 270.336 mm
Number of color 262 K
Input signals R.G.B Analog, 15 pin D-sub
Frequency rate Horizontal : 31.0 to 80.0KHz, Vertical : 56 to 75Hz
Maximum bandwidth 135 MHz
Maximum resolution 1280 x 1024@75Hz
Recommanded resolution 1280 x 1024@60Hz
Input voltage 100-240 VAC, 1.0A
Power consumption 40W
Power management VESA DPMS
Plug & Play VESA DDC 1/2B
BRIGHTNESS, CONTRAST, COLOR CONTROL,
OSD menu MISCELLANEOUS, AUDIO, AUTO ADJUST, LANGUAGE,
H/V. POSITION, CLOCK-PHASE, SOURCE
Built in Speaker 2ch x 2watts
VESA FPMPMI 75 x 75 mm screw mounting
Ergonomics, TCO, FCC Class B, CE,
Safety and EMC cULus, TÜV-GS, SEMKO
Operating Temperature 5 ~ 35O C
Weight 4.6Kg unpacked, 6.1Kg packed
Dimensions (W X H X D mm) 372 X 395 X 185 mm
• Specification is subject to change without notice for performance improvement.
28
--27--
TECHNICAL SERVICE MANUAL Prestigio P170T
Features
- Low Voltage and Standard Voltage Operation
- 5.0 (VCC = 4.5V to 5.5V)
- 2.7 (VCC = 2.7V to 5.5V)
- 2.5 (VCC = 2.5V to 5.5V)
- 1.8 (VCC = 1.8V to 5.5V)
- Internally Organized 2048 x 8 (16K)
- 2-Wire Serial Interface
- Schmitt Trigger, Filtered Inputs for Noise Suppression
- Bidirectional Data Transfer Protocol
- 100 kHz (1.8V, 2.5V, 2.7V) and 400 kHz (5V) Compatibility
- Write Protect Pin for Hardware Data Protection
- Cascadable Feature Allows for Extended Densities
- 16-Byte Page Write Mode
- Partial Page Writes Are Allowed
- Self-Timed Write Cycle (10 ms max)
- High Reliability
- Endurance: 1 Million Write Cycles
- Data Retention: 100 Years
- ESD Protection: >3,000V
- Automotive Grade and Extended Temperature Devices Available
- 8-Pin JEDEC SOIC and 8-Pin PDIP Packages
Description
The AT24C164 provides 16,384 bits of serial electrically erasable and programmable
read only memory (EEPROM) organized as 2048 words of 8 bits each. The deviceís
cascadable feature allows up to eight devices to share a common 2-wire bus. The
device is optimized for use in many industrial and commercial applications where low
power and low voltage operation are essential. The AT24C164 is available in space
saving 8-pin PDIP and 8-pin SOIC packages and is accessed via a 2-wire serial inter-
face. In addition, this device is available in 5.0V (4.5V to 5.5V), 2.7V (2.7V to 5.5V),
2.5V (2.5V to 5.5V) and 1.8V (1.8V to 5.5V) versions.
Pin Configurations
Pin Name Function
A0 - A2 Address Inputs
SDA Serial Data
SCL Serial Clock Input
WP Write Protect
A0 1 8 VCC A0 1 8 VCC
A1 2 7 WP A1 2 7 WP
A2 3 6 SCL A2 3 6 SCL
GND 4 5 SDA GND 4 5 SDA
29
Prestigio P170T TECHNICAL SERVICE MANUAL
Block Diagram
WP
Pin Description one of eight possible devices sharing a common bus. The
AT24C164 can be made compatible with the AT24C16 by
SERIAL CLOCK (SCL): The SCL input is used to positive
tying A2, A1 and A0 to VSS. Device addressing is discussed
edge clock data into each EEPROM device and negative
in detail in the device addressing section.
edge clock data out of each device.
WRITE PROTECT (WP): The write protect input, when tied
SERIAL DATA (SDA): The SDA pin is bidirectional for
low to GND, allows normal write operations.
serial data transfer. This pin is open-drain driven and may
be wire-ORed with any number of other open-drain or open
collector devices. Memory Organization
DEVICE SELECT (A2, A1, A0): The A2, A1 and A0 pins The AT24C164 is internally organized with 256 pages of
are device address inputs that may be hardwired or actively 8 bytes each. Random word addressing requires an 11 bit
driven to VDD or VSS. These inputs allow the selection for data word address.
30
TECHNICAL SERVICE MANUAL Prestigio P170T
RC1117
MC68HC705BD7B
RC1117
1A Adjustable/Fixed Low Dropout Linear Regulator
Features Description
• Low dropout voltage The RC1117 and RC1117-2.5, -2.85, -3.3 and -5 are low
• Load regulation: 0.05% typical dropout three-terminal regulators with 1A output current
• Trimmed current limit capability. These devices have been optimized for low voltage
• On-chip thermal limiting where transient response and minimum input voltage are
• Standard SOT-223 and TO-263 packages critical. The 2.85V version is designed specifically to be
• Three-terminal adjustable or fixed 2.5V, 2.85V, 3.3V, 5V used in Active Terminators for SCSI bus.
Typical Applications
RC1117
24.9
RC1117-2.85
31
Prestigio P170T TECHNICAL SERVICE MANUAL
Pin Assignments
Tab is
Front View VOUT
3 IN
Tab is
VOUT 2 OUT
1 ADJ/GND
ADJ/ OUT IN
GND
*With package soldered to 0.5 square inch copper area over backside ground plane or internal power plane., ΘJA can vary from
30°C/W to more than 50°C/W. Other mounting techniques may provide better thermal resistance than 30°C/W.
32
TECHNICAL SERVICE MANUAL Prestigio P170T
Electrical Characteristics
Operating Conditions: VIN ≤ 7V, TJ = 25°C unless otherwise specified.
The • denotes specifications which apply over the specified operating temperature range.
33
Prestigio P170T TECHNICAL SERVICE MANUAL
TDA7496L
MC68HC705BD7B
BLOCK DIAGRAM
VAROUT_R VS
7 15,16
GND 1,2,3,13,
18,19,20 VOLUME
9 1000µF
INR + 14
470nF 30K - OUTR
OP AMP
S1 ST-BY
+5V
11 STBY
MUTE/STBY S_GND
10K
PROTECTIONS
12 MUTE
60K 1µF +5V
VOLUME S2 MUTE
4
INL + 17 OUTL
470nF 30K -
1000µF
OP AMP
SVR 10
470µF 6 5
VOLUME VAROUT_L
+5V
D97AU596A
300K
100nF
34
TECHNICAL SERVICE MANUAL Prestigio P170T
PIN CONNECTION Rth with "on board" Square Heatsink vs. cop-
per area.
Rthj-a D97AU675
GND 1 20 GND (∞C/W) COPPER AREA 35µ
THICKNESS
GND 2 19 GND
GND 3 18 GND
60
INL 4 17 OUTL
VAROUT_L 5 16 VS
PC BOARD
VOLUME 6 15 VS 50
VAROUT_R 7 14 OUTR
N.C. 8 13 GND
40
INR 9 12 MUTE
SVR 10 11 STBY
D97AU597A 30
0 4 8 12 Area(cm2)
THERMAL DATA
Symbol Parameter Value Unit
Rth j-pins Thermal Resistance Junction-pins max. 15 ∞C/W
Rth j-amb (*) Thermal Resistance Junction-ambient max. 50 ∞C/W
(*) Mounted on PCB with no heatsink
ELECTRICAL CHARACTERISTICS (Refer to the test circuit VS = 14V; RL = 8Ω, Rg = 50Ω, Tamb = 25∞C).
Symbol Parameter Test Condition Min. Typ. Max. Unit
VS Supply Voltage Range 10 18 V
Iq Total Quiescent Current 25 50 mA
DCVOS Output DC Offset Referred to No Input Signal 200 mV
SVR Potenial
VO Quiescent Output Voltage 7 V
PO Output Power THD = 10%; RL = 8Ω; 1 .6 2 W
THD = 1%; RL = 8Ω; 1 .3 W
THD Total Harmonic Distortion GV = 30dB; PO = 1W; f = 1KHz; 0.4 %
Ipeak Output Peak Current (internally limited) 0.7 0.9 A
Vin Input Signal 2.8 Vrms
GV Closed Loop Gain Vol Ctrl > 4.5V 28.5 30 31.5 dB
GvLine Monitor Out Gain Vol Ctrl > 4.5V; Zload > 30KΩ -1.5 0 1.5 dB
AMin VOL Attenuation at Minimum Volume Vol Ctrl < 0.5V 80 dB
BW 0.6 MHz
35
Prestigio P170T TECHNICAL SERVICE MANUAL
APPLICATION SUGGESTIONS
The recommended values of the external components are those shown on the application circuit of fig-
ure 1A. Different values can be used, the following table can help the designer.
SUGGESTION LARGER THAN SMALLER THAN
COMPONENT PURPOSE
VALUE SUGGESTION SUGGESTION
R1 300K Volume control Larger volume regulation Smaller volume regulation
circuit time time
R2 10K Mute time constant Larger mute on/off time Smaller mute on/off time
P1 50K Volume control
circuit
C1 1000µF Supply voltage Danger of oscillation
bypass
C2 470nF Input DC decoupling Lower low frequency cutoff Higher low frequency cutoff
C3 470nF Input DC decoupling Lower low frequency cutoff Higher low frequency cutoff
C4 470µF Ripple rejection Better SVR Worse SVR
C5 100nF Volume control time Larger volume regulation Smaller volume regulation
costant time time
C6 1000µF Output DC Lower low frequency cutoff Higher low frequency cutoff
decoupling
C7 1µF Mute time costant Larger mute on/off time Smaller mute on/off time
C8 1000µF Output DC Lower low frequency cutoff Higher low frequency cutoff
decoupling
C9 100nF Supply voltage Danger of oscillation
bypass
36
TECHNICAL SERVICE MANUAL Prestigio P170T
NT68F632V2
MC68HC705BD7B
37
Prestigio P170T TECHNICAL SERVICE MANUAL
PC5/PATTO
PC3/PWM0
PC4/PWM1
PC2/SOGI
VSYNCI
HSYNCI
RSTB
PC0*
PC1*
VCC
PD6
PC2/SOGI 1 42 VSYNCI
PC1* 2 41 HSYNCI
PC0* 3 40 PC3/PWM0
44
43
42
41
40
6
5
4
3
2
1
RSTB 4 39 PC4/PWM1
GND 7 39 PE1
VCC 5 38 PC5/PATTO
PD6 6 37 PC6 OSCO 8 38 PE0
GND 7 36 PC7 OSCI 9 37 PC6
NT68F632U
OSCO 8 35 PD0 P30/RXD 10 36 PC7
OSCI 9 34 PD1/HSYNCO
P31/TXD 11 35 PD0
P30/RXD 10 33 PD2/VSYNCO
P31/TXD 11 32 PD3/HALFO P34/T0 12 NT68F632L 34 PD1/HSYNCO
P34/T0 12 31 PD4/HALFI P35/T1 13 33 PD2/VSYNCO
P35/T1 13 30 PD5/CLMPO PB3/ADC3/INTE1 14 32 PD3/HALFO
PB3/ADC3/INTE1 14 29 PA0/PWM2
PB2/ADC2/INTE0 15 31 PD4/HALFI
PB2/ADC2/INTE0 15 28 PB4*/SCL0*
PB1/ADC1 16 27 PB5*/SDA0* PB1/ADC1 16 30 PD5/CLMPO
PB0/ADC0 17 26 PB6*/SCL1* PB0/ADC0 17 29 PA0/PWM2
18
19
20
21
22
23
24
25
26
27
28
PA7*/PWM9* 18 25 PB7*/SDA1*
PA6*/PWM8* 19 24 PA1/PWM3
PA5*/PWM7* 20 23 PA2/PWM4
PA7*/PWM9*
PA6*/PWM8*
PA5*/PWM7*
PA4*/PWM6*
PA3/PWM5
PA2/PWM4
PA1/PWM3
PB7*/SDA1*
PB6*/SCL1*
PB5*/SDA0*
PB4*/SCL0*
PA4*/PWM6* 21 22 PA3/PWM5
42-Pin S-DIP
44-Pin PLCC
38
TECHNICAL SERVICE MANUAL Prestigio P170T
1-4 Block Diagram
JEDEC 8-bit
2K-Byte
32K-Byte *4Bank PWM DAC
Boot ROM
Flash Memory *10
39
Prestigio P170T TECHNICAL SERVICE MANUAL
TDA7440D
MC68HC705BD7B
INPUT MULTIPLEXER
- 4 STEREO INPUTS
- SELECTABLE INPUT GAIN FOR OPTIMAL
ADAPTATION TO DIFFERENT SOURCES
ONE STEREO OUTPUT
TREBLE AND BASS CONTROL IN 2.0dB
STEPS SO28
VOLUME CONTROL IN 1.0dB STEPS
TWO SPEAKER ATTENUATORS:
ORDERING NUMBER: TDA7440D
- TWO INDEPENDENT SPEAKER CONTROL
IN 1.0dB STEPS FOR BALANCE FACILITY
- INDEPENDENT MUTE FUNCTION
ALL FUNCTION ARE PROGRAMMABLE VIA Selectable input gain is provided. Control of all
SERIAL BUS the functions is accomplished by serial bus.
The AC signal setting is obtained by resistor net-
works and switches combined with operational
DESCRIPTION amplifiers.
The TDA7440D is a volume tone (bass and Thanks to the used BIPOLAR/CMOS Technology,
treble) balance (Left/Right) processor for quality Low Distortion, Low Noise and DC stepping are
audio applications in Hi-Fi systems. obtained
BLOCK DIAGRAM
5
L-IN2
100K
SPKR ATT 27
6 G VOLUME TREBLE BASS LOUT
L-IN3 LEFT
100K
7
L-IN4
100K
21
0/30dB 2
SCL
2dB STEP I CBUS DECODER + LATCHES 22
3 SDA
R-IN1 20
DIG_GND
100K
2
R-IN2
100K SPKR ATT 26
G VOLUME TREBLE BASS ROUT
RIGHT
1
R-IN3 VREF
100K
24
28 VS
R-IN4 SUPPLY 25
INPUT MULTIPLEXER RB AGND
100K + GAIN
10 11 19 12 13 23
MUXOUTR INR TREBLE(R) BIN(R) BOUT(R) CREF D98AU883
40
TECHNICAL SERVICE MANUAL Prestigio P170T
R_IN3 1 28 R_IN4
R_IN2 2 27 LOUT
R_IN1 3 26 ROUT
L_IN1 4 25 AGND
L_IN2 5 24 VS
L_IN3 6 23 CREF
L_IN4 7 22 SDA
MUXOUTL 8 21 SCL
IN(L) 9 20 DIG-GND
MUXOUT(R) 10 19 TREBLE(R)
IN(R) 11 18 TREBLE(L)
BIN(R) 12 17 N.C.
BOUT(R) 13 16 N.C.
BIN(L) 14 15 BOUT(L)
D98AU884
THERMAL DATA
Symbol Parameter Value Unit
R th j-pin Thermal Resistance Junction-pins 85 5C/W
41
5 4 3 2 1
12MHz
LVDS
15PIN Scaler NT7181-11
D-SUB
NT68520E-QFP160
C LVDS 17" C
LCD
NT7181-11 PANEL
COMPOSITE
VIDEO
VIDEO
DECORDER
S-VIDEO VPX3226E
EEPROM
MCU (24CXX)
NT68F632
TV TUNER
INVERTER
12MHz
B B
POWER
12V/5V
AUDIO
PROCESSOR AUDIO AMP
TDA7496L
TDA7440D
A A
Title
PRESTIGIO
P170T/P190T
Size Document Number Rev
9/ 2
NO LOCATION PART NUMBER DESCRIPTION REMARK
9/ 3
NO LOCATION PART NUMBER DESCRIPTION REMARK
9/ 4
NO LOCATION PART NUMBER DESCRIPTION REMARK
9/ 5
NO LOCATION PART NUMBER DESCRIPTION REMARK
9/ 6
NO LOCATION PART NUMBER DESCRIPTION REMARK
9/ 7
NO LOCATION PART NUMBER DESCRIPTION REMARK
9/ 8
NO LOCATION PART NUMBER DESCRIPTION REMARK
9/ 9
5 4 3 2 1
VD_VS P3
VD[0..7] P2
VD0
VD1
VD2
VD3
VD4
VD5
D D
VD6
VD7
C101
220nF
GND_VPX
GND_VPX U101
33
32
31
30
29
28
27
26
25
24
23
PIXCLK
PVDD
PVSS
A7
A6
A5
A4
A3
A2
A1
A0
R150 R151 R152
VD_OE
34 FIELD /OE 22 P3
0
35 21 VCLK P2
DGND GND_VPX VREF LLC
36 HREF VACT 20
C 37 19 C
TDO(DACT,LLC2) B7
38 TCK VPX3226E B6 18
39 TDI B5 17
GND_VPX
40 TMS B4 16
41 ISGND B3 15
XTAL1
XTAL2
AVDD
AVSS
DGND
/RES
VIN1
VDD
SDA
VSS
SCL
CIN
GND_VPX GND_VPX GND_VPX
GND_VPX
10
11
1
9
L102 C119 680nF
B
P3 CVBS 2012 2.2uH B
C120 C121
R102
330pF 330pF GND_VPX GND_VPX
75 VD_SDA P3
VD_SCL P3
GND_VPX GND_VPX GND_VPX RSTN P3, P2
3.3V2
L103 C102 1nF
P3 S-VIDEO_Chroma 2012 2.2uH
5V
GND_VPX GND_VPX GND_VPX
3.3V1 DPP_VAA
L202HB 600 1608 ADC_VAA PLL_VAA 3.3V1
DPP_VAA
C202 C203 C204 C205 C206 C207 C208 C209 C210 C211 C212 C213 CVDD1
22uF/16V + C201 + C214 CVDD2
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 22uF/16V CVDD3
L203 0
DGND
C215 C216 C217
100
118
121
145
146
120
134
133
132
131
130
129
128
127
126
125
124
123
122
DGND U201
30
32
12
17
25
14
22
27
45
46
64
78
82
42
77
87
8
2
3
DPP_GND DGND
VCC
ADC_GVAA
GVAA
DVDD
DVDD
DVDD
DVDD
DVDD
DVDD
DVDD
DVDD
ADC_RVAA
ADC_BVAA
RVAA
VDD
VDD
CVDD
CVDD
CVDD
NC
NC
BVAA
G3
G2
G1
G0
D
DPP_VAA1
BIAS_VAA
B7
B6
B5
B4
B3
B2
B1
B0
D
PLL_VDD
PLL_VAA
117 BA0
BA0 BA1
BA1 116
IRQN 156 115 BA2
P3 IRQn BA2 BA3
BA3 114
R204 BA4
BA4 113
ADC_VAA 9 112 BA5
Vref BA5 BA6
19 Vtop BA6 111
820 20 110 BA7
Vmid BA7
21 Vbot
1
C229
NT68520E-QFP160 NC 74
NC 73
22pF NC C230 35
22pF NC OSCI RB7
Y201 36 72
C231 OSCO RB7 RB6
RB6 71
22pF NC P3 RSTN 158 70 RB5
SC_SDA RSTn RB5 RB4
12MHz P3 154 69
3.3V1 SC_SCL SDA RB4 RB3
P3 155 SCL RB3 68
C226 C227 67 RB2
10pF 10pF R201 NC RB2 RB1
RB1 66
65 RBO
R202 NC RB0
ADC_GND DGND 63 GB7
GB7 GB6
38 HSYNCI GB6 62
40 61 GB5
VSYNCI GB5 GB4
GB4 60
R209 NC 59 GB3
GB3 GB2
GB2 58
U202D C254 148 57 GB1
U202C HSYNCO GB1 GBO
10pF 149 VSYNCO GB0 56
MIDBIAS_GNDA
PBUSSEL BB0
I2C_ADDR0/R4
I2C_ADDR1/R5
U202E U202F C233 33pF 43 TCON_EN
ADC_GGNDA
ADC_RGNDA
ADC_BGNDA
DPP_GNDA1
BIAS_GNDA
159 37
CVDD_CAP
147 CVDD_CAP
PLL_HS DCLK_SRC
PLL_GNDA
DGND 79 DISP_DE
PLL_GND
VSI R213 0 R214 0 DISP_DE DISP_HS
GGNDA
RGNDA
P4
BGNDA
11 10 13 12 DISP_HS 83
CGND
CGND
CGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
PLL_GND 80 DISP_VS
DISP_VS P6
DEI
NC
NC
NC
NC
R6
R7
74HC14 74HC14
5V
119
109
135
160
150
151
152
153
157
81
33
31
16
13
24
18
29
26
34
44
55
75
86
89
76
88
84
85
R212 NC
1
6
7
C234
0.1uF
U202A U202B C236
14
14
DGND + 10uF/16V +
C235
P4 HSI R203 100 PLL_HS 1 2 3 4 10uF/16V
3.3V2 L204 HB 600 1608 PLL_VAA
74HC14 74HC14
SOP14 DPP_GND C238
DGND DGND 22uF/16V C239
7
+ +
C237 DGND 0.1uF C240 C241
10pF PLL_GND ADC_GND 22uF/16V 0.1uF
DGND L205 0
ADC_VAA
A L206HB 600 1608 A
3.3V1 AGND PLL_GND
Title
PRESTIGIO
DGND
P170T
ADC_GND Size Document Number Rev
NT68520 VP1
Date: Wednesday, April 23, 2003 Sheet 2 of 6
5 4 3 2 1
5 4 3 2 1
5V 3.3V1
3.3V1
R309
R302
330 1.5K
C303
47uF/16V
+
D R303 100 BL_EN P5 D
LCD_EN P5 + C302
10uF/16V
DGND
U301
1 PC2/SOGI VSYNCI 44 VSI P4
2 43 R358 220 P4
PC1* HSYNCI HSI
3 42 5V
R357 4.7K PC0* PC3/PWM0 RSTN
4 RSTB PC4/PWM1 41 P1,P2
5 40 12V
VCC PC5/PATTO
6 PD6 PE1 39
7 38 VD_OE P1
GND PE0
8 OSCO PC6 37 VGA_DET P4
R305 1M 9 36 EEP_WP
RXD OSCI PC7
10 P30/RXD PD0 35 VD_VS
TXD 11 34 P1
MSCL P31/TXD PD1/HSYNCO
12 P34/T0 PD2/VSYNCO 33
Y301 MSDA 13 32 AUDIO_MUTE
C IR_INT P35/T1 PD3/HALFO C
14 PB3/ADC3/INTE1 PD4/HALFI 31
P2 IRQN 15 30 LVDS_PWN P6
12MHZ MENU PB2/ADC2/INTE0 PD5/CLMPO R330 56 AUDIO_VOLUME
16 PB1/ADC1 PA0/PWM2 29
SELECT 17 28 CN301
KEY_UP PB0/ADC0 PB4*/SCL0*
18 PA7*/PWM9* PB5*/SDA0* 27
C304 C305 KEY_DOWN 19 26 R351 0 P4 1
KEY_SOURCE PA6*/PWM8* PB6*/SCL1* R352 0 DDC_SCL Z02W5.6V + C316 12V
20 PA5*/PWM7* PB7*/SDA1* 25
PWR_LEDA DDC_SDA P4
27pF 27pF 21 24 D301 10uF/16V 2
PWR_SW PA4*/PWM6* PA1/PWM3 PWR_LEDG 5V
22 PA3/PWM5 PA2/PWM4 23
3 AUDIO_MUTE
NT68F632 DGND DGND
PLCC44 SOCKET 4 AUDIO_VOLUME
DGND 5 GND
R353 100 6
5V SCL_SUB
R354 100 7 SDA_SUB
P1 TV_VIDEO 8 TV_VIDEO
C315
0.1uF 9 GND
U302 10
DGND P1 CVBS CVBS
1 A0 VCC 8 11 GND
2 7 EEP_WP
A1 WP R319 100 MSCL P1 S-VIDEO_Luma
3 A2 SCLK 6 12 S-VIDEO Luma
4 5 MSDA
B GND SDA R318 100 B
13 GND
DGND 24C16 14
5V SOP8 5V P1 S-VIDEO_Chroma S-VIDEO Chroma
15 GND
ADC_VAA
KDS226
KDS226
KDS226
D D
D401
D402
D403
ADC_GND
5V
L401
BIN P3
0
R402
R403 75
10K
ADC_GND
VGA_DET P3
C C
Z02W5.6V
CN401
10 D406
15 5
9
14 4 DGND
8
13 3
7 L402
12 2 GIN P3
6 0
11 1
R405
75
D-SUB15 FEMAIL
ADC_GND
ADC_GND
HSYNC R406 100 HSI P2,P3
VSYNC R407 100 VSI P2,P3
470pF C401
B B
L403
D404 D405 RIN P3
Z02W5.6V Z02W5.6V DGND 0
R408
75
DGND
ADC_GND
5V
R409 R410
4.7K 4.7K
DDC_SDA P3
DDC_SCL P3
A A
Title
PRESTIGIO
P170T
Size Document Number Rev
D D
3.3V1
5V U501
RC1117_3.3
3 2 5V LCDVDD
VIN VOUT
3
100uF/16V 0.1uF
DGND
DGND DGND
DGND
3
3.3V2 R502 47K Q501
5V U503 LCD_EN 1
P3 TT2N3904D
RC1117_3.3
2
3 VIN VOUT 2
C503
GND 1uF
+ C504 C506
+ C505 C507 SOT223
1 22uF/16V 0.1uF
22uF/16V 0.1uF DGND
DGND DGND
AGND
DGND 5V
B B
12V
CON503
1
2
3
+ 4
C508 C509 5
100uF/16V 0.1uF 6
7
DGND DGND HEADER 7
P3 BL_EN
P3 BL_BRIGHT
DGND
A A
Title
PRESTIGIO
P170T
Size Document Number Rev
POWER VP2
Date: Wednesday, April 23, 2003 Sheet 5 of 6
5 4 3 2 1
5 4 3.3V2
3 2 1
C601 C602 C603 C604
U601
0.1uF 0.1uF 0.1uF 0.1uF
1 VCC TD4 56 RA4
RA7 2 TD5 TD3 55 RA3
RA5 3 TD6 TD2 54 RA2
LVDS_GND GA0 4 TD7 GND 53
5 GND TD1 52 RA1 P2
GA1 6 TD8 TD0 51 RA0
GA2 7 TD9 TD27 50 RA6
D GA6 8
9
TD10
VCC
LVDSGND
T0M
49
48 T0M_A D
10 47 T0P_A
GA7 TD11 T0P
11 46 T1M_A
GA3 TD12 T1M
12 45 T1P_A
GA4 TD13 T1P
P2 13 44 LVDSVCC
GND LVDSVCC
GA5 14 TD14 LVDSGND 43
15 NT7181-11 42 T2M_A
BA0 TD15 T2M
16 41 T2P_A
BA6 TD16 T2P CN601
17 40 TCLKM_A
RFB TCLKM TCLKP_A T0M_A
BA7 18 TD17 TCLKP 39 30
19 38 T3M_A T0P_A
BA1 TD18 T3M 29
20 37 T3P_A T1M_A
BA2 TD19 T3P 28
21 36 T1P_A
GND LVDSGND T2M_A 27
BA3 22 TD20 PLLGND 35 26
23 34 PLLVCC T2P_A
BA4 TD21 PLLVCC 25
BA5 24 TD22 PLLGND 33 24
25 32 LVDS_PWN R605 0 TCLKM_A
TD23 PWDN# DCLK P3 R606 0 TCLKP_A 23
26 VCC CLKIN 31 22
DISP_HS 27 30 T3M_A
DISP_VS TD24 TD26 T3P_A 21
28 TD25 GND 29 20
DISP_DE T0M_B
T0P_B 19
NT7181-11 18
T1M_B 17
LVDS_GND T1P_B 16
LVDS_GND 15
T2M_B 14
T2P_B 13
R607 0 TCLKM_B 12
C R608 0 TCLKP_B 11
10
C
T3M_B
T3P_B 9
8
7
DCLK 6
R604 0 LCDVDD 5
DISP_DE 4
P2 3
R602 0
DISP_HS 2
C615 C616
R601 0 1
DISP_VS
NC NC HEADER30
LVDS_GND
C613 C614
NC NC 3.3V2
U602
NT7181-11
L603
LVDS_GND LVDS_GND
NC
DGND C605 C606 C608 C609 C610
+ C607
A LVDS_GND 0.1uF 0.1uF 22uF/16V 0.1uF 1uF 1uF
0603
A
LVDS_GND
PRESTIGIO
Title
P170T
Size Document Number Rev
A3 VP2
LVDS OUTPUT
Date: Wednesday, April 23, 2003 Sheet 6 of 6
5 4 3 2 1
WAVE FORM
4/ 1
Y201 X-tal 12Mhz Xout Y301 X-tal 12Mhz Xin
4/ 2
MSCL MSDA
LCD_EN DCLK
TCLKM_A TCLKM_B
4/ 3
TCLKP_A TCLKP_B
4/ 4