Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
A
D
F
H
G
1/8 50 M244 1/8-24UNC 0.72 0.44 0.47 0.42 0.38 0.81 1.09 2 4-1/2 3-1/4 0.08
3/16 50 M245 1/4-20UNC 0.94 0.56 0.59 0.50 0.50 0.94 1.19 2 7-1/2 3-3/4 0.12
1/4 50 M246 5/16-18UNC 1.03 0.50 0.75 0.66 0.56 1.19 1.44 2 15 4-3/4 0.18
5/16 50 M247 3/8-16UNC 1.38 0.75 0.88 0.72 0.69 1.31 1.69 2 30 5-1/4 0.30
3/8 50 M248 7/16-14UNC 1.50 0.75 1.00 0.91 0.75 1.63 1.94 2 45 6-1/2 0.42
7/16 50 M249 1/2-13UNC 1.88 1.00 1.19 1.06 0.88 1.78 2.31 2 65 7 0.70
1/2 20 M250 1/2-13UNC 1.88 1.00 1.19 1.16 0.88 1.91 2.31 3 65 11-1/2 0.85
9/16 20 M296 9/16-12UNC 2.38 1.25 1.31 1.24 0.94 1.94 2.50 3 95 12 1.00
5/8 20 M251 9/16-12UNC 2.38 1.25 1.31 1.34 0.94 2.00 2.49 3 95 12 1.00
3/4 10 M252 5/8-11UNC 2.75 1.44 1.50 1.44 1.06 2.34 2.81 4 130 18 1.53
7/8 10 M253 3/4-10UNC 3.13 1.63 1.75 1.63 1.25 2.44 3.16 4 225 20 2.40
1 10 M254 3/4-10UNC 3.50 1.81 1.88 1.78 1.25 2.63 3.47 5 225 26 2.50
1-1/8 5 M255 3/4-10UNC 3.88 2.00 2.00 1.88 1.25 2.81 3.59 6 225 34 3.10
1-1/4 5 M256 7/8-9UNC 4.25 2.13 2.31 2.19 1.44 3.15 4.22 7 360 37 4.10
1-3/8 5 M257 7/8-9UNC 4.63 2.31 2.38 2.25 1.44 3.08 4.25 7 360 44 4.50
1-1/2 5 M258 7/8-9UNC 4.94 2.38 2.59 2.50 1.44 3.41 4.47 8 360 48 5.40
NOTE: 1/8" through 5/8" packed 1 piece per poly bag. 3/4" & larger shipped assembled in factory packs and tagged.
RIGGING HARDWARE
Live
PROPER USE OF WIRE ROPE CLIPS end
1. Refer to the chart above when following these instructions. Turn back specified
amount of rope from thimble or loop. Apply first clip one base width from dead
end of rope. Apply U-bolt over dead end of wire rope, ensuring live end rests in
saddle. Tighten nuts evenly, alternate from one nut to the other until reaching the Dead
End
recommended torque.
2. When two clips are required, apply the second clip as near the thimble or loop
as possible. Tighten nuts evenly, alternating until reaching the recommended Saddle
torque. When more than two clips are required, apply the second clip as near
the loop or thimble as possible and turn nuts on second clip firmly, but do not
tighten. Proceed to Step 3. U-bolt
3. When three or more clips are required, space additional clips equally between 1 2 3
the first two and take up rope slack. Then tighten nuts on each U-bolt evenly,
alternating from one nut to the other until reaching the recommended torque. Live Side
4. Apply an initial load equal to loads expected in use. Inspect for proper Dead End
orientation and spacing of clips and retighten the nuts to recommended torque. NOTE: Mechanical spliced or flemished eyes slings are the preferred method of wire rope sling construction.
OSHA does not allow the use of clips to form the eyes of wire rope slings.
CARE INSPECTION
Care should be exercised in the installation Visually inspect wire
and use of wire rope clips so that the clip, rope clips
wire rope, or thimble is not damaged. before each use. NEVER INSTALL THE U-BOLT
Do not over torque or under torque the nuts. Be certain threads are ON THE LIVE SIDE!
Too much torque can result in damage to the not stripped and that
clip and/or the wire rope. Too little torque can nuts are tight.
result in the wire rope slipping. Torque nuts Check torque of nuts
to the value specified in the accompanying periodically. INCORRECT
instructions. Replace distorted thimbles.
Clips should not be subjected to bending Shorten wire rope and form IMPROPER USE
or come in contact with sharp object. new loop if damaged. OF WIRE ROPE CLIPS
INCORRECT
Avoid exposure to corrosive mediums. Replace distorted thimbles.
PRECISE THREADING
Precise threading on bolt and nut ensures
tight alignment and exceptional strength. A
B D
FEWER LOOSE PARTS TO DROP
Hex bolt is knurled and machine pressed into
socket to securely couple with the saddle.
HARDWARE
L Number Turn-Back
800
(in.) Package Code A B C D E Thread F G M N of Clips (in.) (ft./lbs.) (lbs.)
Approx.
®
HERC-ALLOY
New Style
3/16 20 M2546 0.37 1.53 0.44 1.06 3/8 - 16 0.50 1.50 1.93 0.69 1.74 2 4 30 0.38
RIGGING
1/4 20 M2546 0.37 1.53 0.44 1.06 3/8 - 16 0.50 1.50 1.93 0.69 1.74 2 4 30 0.38
5/16 20 M2547 0.34 1.48 0.44 1.06 3/8 - 16 0.63 1.50 1.90 0.69 1.80 2 5 30 0.38
3/8 20 M2548 0.46 1.67 0.54 1.13 7/16 - 14 0.75 1.84 2.26 0.75 2.00 2 5.5 45 0.49
7/16 20 M2550 0.65 2.03 0.59 1.31 1/2 - 13 1.05 2.23 2.74 0.88 2.40 2 6.5 65 0.84
1/2 20 M2550 0.65 2.03 0.59 1.31 1/2 - 13 1.05 2.23 2.74 0.88 2.40 3 11 65 0.84
9/16 20 M2551 0.78 2.46 0.73 1.63 5/8 - 11 1.38 2.81 3.44 1.06 2.90 3 12.75 130 1.55
5/8 20 M2551 0.78 2.46 0.73 1.63 5/8 - 11 1.38 2.81 3.44 1.06 2.90 3 13.5 130 1.55
Old Style
3/4 20 M2252 0.81 2.69 0.88 1.81 3/4 - 10 1.50 3.38 5.00 1.25 3.02 3 16 225 1.79
®
PIGGYBACK WEDGE SOCKET CLIPS
SIZES: 3/8 TO 1-1/2 IN.
F G
E C
B A
3/8 10 M248D 1X248 2X248L 7/16-14UNC 1.00 2.38 0.75 0.69 1.94 1.62 602224 45 6 0.8
7/16 10 M249D 1X249 2X250L 1/2-13UNC 1.19 2.62 1.00 0.66 2.31 1.78 602225 65 6 1.3
1/2 10 M250D 1X250 2X250L 1/2-13UNC 1.19 2.62 1.00 0.72 2.31 1.91 602225 65 6 1.4
9/16 10 M296D 1X296 2X251L 9/16-12UNC 1.31 3.19 1.25 0.77 2.50 1.97 602226 95 6 1.7
5/8 10 M251D 1X251 2X251L 9/16-12UNC 1.31 3.19 1.25 0.87 2.50 2.00 602226 95 6 1.7
3/4 10 M252D 1X252 2X252L 5/8-11UNC 1.50 3.50 1.50 0.91 2.81 2.34 602227 130 6 2.5
7/8 5 M253D 1X253 2X253L 3/4-10UNC 1.75 3.88 2.00 1.07 3.16 2.44 602228 225 6 3.6
1 5 M254D 1X254 2X254L 3/4-10UNC 1.88 4.25 2.00 1.22 3.47 2.62 602228 225 6 3.9
1-1/8 5 M255D 1X255 2X255L 3/4-10UNC 2.00 4.50 2.00 1.31 3.59 2.81 602228 225 6-3/4 4.9
1-1/4 5 M256D 1X256 2X256L 7/8-9UNC 2.31 5.25 2.38 1.50 4.22 3.15 602246 360 7-1/2 6.5
RIGGING HARDWARE
1-3/8 5 M257D 1X257 2X257L 7/8-9UNC 2.38 5.62 2.38 1.56 4.25 3.08 602246 360 8-1/4 7.1
1-1/2 5 M258D 1X258 2X258L 7/8-9UNC 2.59 6.00 2.38 1.75 4.47 3.41 602246 360 9 8.2
BUNDLING CLIP
SIZES: 3/4 TO 1-1/8 IN.
BENEFITS & FEATURES
Galvanized and painted U-bolt with rolled
threads. Interchangeable and replaceable
with our standard wire rope clip U-bolts.
Forged and galvanized saddles come
with FORGED USA, size, CM logo A B
and trace code forged in.
Meets B30.26 plus traceability.
Performs to rated capacities.
After inspection, the CM B
Bundling Clip is reusable. C
HARDWARE
800
BENEFITS & FEATURES
Forged from fine grain, special bar quality
®
HERC-ALLOY
C-1035 steel
Spheroidized annealed for cold swaging
RIGGING
Recommended for use on 6" x 19" or
6" x 37" IWRC regular lay wore ropes.
Can also be used on galvanized bridge rope.
Not for use on fiber core or lang lay ropes. A D
O
Sockets have 100% efficiency rating based M
on catalog strength of wire rope when H B Y
properly applied E
L
F
SWAGE BUTTON
FOR ROPE DIAMETERS: 1/8 TO 1-1/8 IN.
BENEFITS & FEATURES
Fittings machined from specially selected
and processed low carbon steel
Buttons have 98% efficiency rating based on catalog
strength of wire rope when properly applied
Wi1 Wi Wo
P1
P
0.250 Gold 250 697180 1.00 0.66 0.33 0.47 0.28 0.09 0.50 0.04
0.312 Red 200 697181 1.50 0.91 0.44 0.61 0.47 0.14 0.73 0.14
0.375 Green 100 697182 1.50 0.91 0.47 0.66 0.47 0.13 0.73 0.12
0.500 Gold 50 697184 2.00 1.22 0.63 0.91 0.59 0.16 0.98 0.28
0.625 Green 25 697186 2.75 1.47 0.75 1.09 0.70 0.19 1.20 0.56
0.750 Blue 20 697187 3.19 1.72 0.92 1.28 0.86 0.22 1.41 0.88
0.875 Gold 10 697188 3.56 2.01 1.01 1.53 1.00 0.25 1.63 1.38
1.000 Self Colored 10 697189 4.00 2.28 1.16 1.72 1.13 0.28 1.88 1.90
1.250 Self Colored Bulk 697191 5.20 2.78 1.47 2.16 1.41 0.31 2.27 3.40
1.500 Self Colored Bulk 697193 6.25 3.25 1.69 2.63 1.69 0.31 2.65 5.00
1.750 Self Colored Bulk 697194 7.25 3.84 1.94 3.13 1.97 0.36 3.04 8.40
2.000 Self Colored Bulk 697195 8.50 4.38 2.25 3.63 2.25 0.38 3.50 11.30
HARDWARE
2.250 Self Colored Bulk 697196 9.56 5.03 2.50 4.03 2.53 0.50 4.06 19.20
800
2.500 Self Colored Bulk 697197 10.50 5.50 2.75 4.50 2.81 0.50 4.44 23.20
®
HERC-ALLOY
RIGGING
TURNBUCKLES
WORKING LOAD LIMIT: 400 TO 21,400 LBS.
Eye & Eye Jaw & Eye Jaw & Jaw Thread Take
Eye & Eye WLL Weight
Product Weight Product Weight Product Weight Diameter Up (lbs.) (lbs.)
Code (lbs.) Code (lbs.) Code (lbs.) (in.) (in.)
0404EE 0.3 0404JE 0.3 0404JJ 0.4 1/4 4 500 0.4
Jaw & Eye 0504EE 0.5 0504JE 0.5 0504JJ 0.6 5/16 4.5 800 0.6
0606EE 0.8 0606JE 0.9 0606JJ 0.9 3/8 6 1,200 0.9
0806EE 1.5 0806JE 1.7 0806JJ 1.8 1/2 6 2,200 1.8
0809EE 1.9 0809JE 2.0 0809JJ 2.1 1/2 9 2,200 2.1
Jaw & Jaw 0812EE 2.3 0812JE 2.4 0812JJ 2.4 1/2 12 2,200 2.4
1006EE 2.5 1006JE 3.0 1006JJ 3.0 5/8 6 3,500 3.0
1009EE 3.3 1009JE 3.5 1009JJ 3.7 5/8 9 3,500 3.7
1012EE 3.8 1012JE 4.0 1012JJ 4.2 5/8 12 3,500 4.2
Hook & Eye 1206EE 3.9 1206JE 4.3 1206JJ 4.6 3/4 6 5,200 4.6
1209EE 4.8 1209JE 5.1 1209JJ 5.4 3/4 9 5,200 5.4
1212EE 5.4 1212JE 5.7 1212JJ 6.0 3/4 12 5,200 6.0
1218EE 7.0 1218JE 7.3 1218JJ 7.7 3/4 18 5,200 7.7
1412EE 7.4 1412JE 7.9 1412JJ 8.4 7/8 12 7,200 8.4
Hook & Hook
1418EE 9.6 1418JE 10.2 1418JJ 10.7 7/8 18 7,200 10.7
1606EE 9.0 1606JE 9.4 1606JJ 9.7 1 6 10,000 9.7
CARE & INSPECTION 1612EE 11.2 1612JE 11.6 1612JJ 11.9 1 12 10,000 11.9
Inspect turnbuckles before use for bent components 1618EE 13.8 1618JE 14.3 1618JJ 14.8 1 18 10,000 14.8
and worn threads. Do not use if body or end fitting 1624EE 17.1 1624JE 17.6 1624JJ 18.2 1 24 10,000 18.2
is bent more than 10º from the axial center line. 2012EE 20.9 – – 2012JJ 23.8 1-1/4 12 15,200 23.8
Do not use if threads are visibly worn or feel loose.
HARDWARE
800
2018EE 25.7 – – 2018JJ 27.5 1-1/4 18 15,200 27.5
If in doubt, consult a rigging handbook or discuss
2024EE 29.7 – – 2024JJ 33.7 1-1/4 24 15,200 33.7
with a qualified person.
®
2412EE 29 – – 2412JJ 38.1 1-1/2 12 21,400 38.1
HERC-ALLOY
2418EE 35.2 – – 2418JJ 44.2 1-1/2 18 21,400 44.2
2424EE 40.7 – – 2424JJ 48.4 1-1/2 24 21,400 48.4
RIGGING
Imported.
Improper use or care of turnbuckles can result
in bodily injury or property damage. To avoid injury:
V Inspect turnbuckles for distortion and wear. Product Code Thread Diameter Take Up WLL Weight
V Do not use if anything is in contact with the turnbuckle (in.) (in.) (lbs.) (lbs.)
Hook & Eye Hook & Hook
body or an end fitting.
V Only apply load to center of eyes and bowl of hooks. 0404HE 0404HH 1/4 4 400 –
V Do not exceed working load limit. 0504HE 0504HH 5/16 4-1/2 700 –
0606HE 0606HH 3/8 6 1,000 0.8
0806HE 0806HH 1/2 6 1,500 1.5
0809HE 0809HH 1/2 9 1,500 1.9
0812HE 0812HH 1/2 12 1,500 2.3
TURNBUCKLEE 1006HE 1006HH 5/8 6 2,250 2.5
LOCK NUTS 1009HE 1009HH 5/8 9 2,250 3.3
Product Code 1012HE 1012HH 5/8 12 2,250 3.8
Size Weight 1206HE 1206HH 3/4 6 3,000 3.9
(in.) Right Hang Nut Left Hang Nut (lbs
(lbs.))
1209HE 1209HH 3/4 9 3,000 4.8
1/4 3X845 3X845L 0.005 1212HE 1212HH 3/4 12 3,000 5.4
5/16 – 3X846L 0.008 1218HE 1218HH 3/4 18 3,000 7.0
3/8 3X847 3X847L 0.010 1412HE 1412HH 7/8 12 4,000 7.4
1/2 3X849 3X849L 0.030 1418HE 1418HH 7/8 18 4,000 9.6
5/8 – 3X850L 0.050 1606HE 1606HH 1 6 5,000 9.0
3/4 – 3X851L 0.090 1612HE 1612HH 1 12 5,000 11.2
7/8 – 3X852L 0.130 1618HE 1618HH 1 18 5,000 13.8
1 – 3X853L 0.200 1624HE 1624HH 1 24 5,000 17.1
1-1/4 – 3X855L 0.410 2418HE 2418HH 1-1/2 18 7,500 31.2
1-1/2 – 3X866L 0.700 2424HE 2424HH 1-1/2 24 7,500 38.2
Imported. Hot Dip Galvanized. Imported.