Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
CALCULATION
REPORT
5/18/2020
WARNING DEVICE
(OVERHANG)
SIMPLE TECH ONE CO., LTD.
Simple Tech One Co., Ltd.
TABLE OF CONTENTS
1
Simple Tech One Co., Ltd.
2
Simple Tech One Co., Ltd.
2. 3D MODEL
3. SUMMARY REPORT
(1). LOADING
3
Simple Tech One Co., Ltd.
AUTO SEISMIC LOAD
MATERIAL PROPERTIES
4
Project SimpleJob Ref.One Co., Ltd.
Tech
WIND LOADING
In accordance with ASCE7-10
Using the directional design method
16.5 ft
3 ft
1 ft 3 ft
Plan Elevation
Building data
Type of roof; Flat
Length of building; b = 1.00 ft
Width of building; d = 3.00 ft
Height to eaves; H = 16.50 ft
Mean height; h = 16.50 ft
General wind load requirements
Basic wind speed; V = 100.0 mph
Risk category; I
Velocity pressure exponent coef (Table 26.6-1); Kd = 0.85
Exposure category (cl 26.7.3); B
Enclosure classification (cl.26.10); Enclosed buildings
Internal pressure coef +ve (Table 26.11-1); GCpi_p = 0.18
Internal pressure coef –ve (Table 26.11-1); GCpi_n = -0.18
Gust effect factor; Gf = 0.85
Minimum design wind loading (cl.27.4.7); pmin_r = 8 lb/ft2
Topography
Topography factor not significant; Kzt = 1.0
Velocity pressure equation; q = 0.00256 Kz Kzt Kd V2 1psf/mph2;
5
Project SimpleJob Ref.One Co., Ltd.
Tech
3 ft
3 ft
A
Wind - 0o
16.5 ft
16.5 ft
C 0.8 B
3 ft 1 ft 1 ft
Side face Windward face Leeward face
6
ETABS Sweet Tech
Simple Tech One Co., Ltd.
B E G I N A N A L Y S I S
2020/05/20 19:30:39
E L E M E N T F O R M A T I O N
19:30:39
E Q U A T I O N S O L U T I O N
19:30:40
J O I N T O U T P U T
19:30:40
G L O B A L F O R C E B A L A N C E R E L A T I V E E
R R O R S
LOAD FX FY FZ MX
MY MZ
DL .000000 .000000
3.61E-14 .000000 .000000 .000000
WX 2.47E-11 .000000 .000000 .000000
3.00E-11 .000000
IW .000000 .000000
5.55E-14 .000000 .000000 .000000
EX 3.00E-11 .000000 .000000 .000000
3.65E-11 .000000
TRIBUTAR .000000 .000000 .000000 .000000 .
10
Simple Tech One Co., Ltd.
000000 .000000
E L E M E N T J O I N T - F O R C E O U T P U T
19:30:40
E L E M E N T O U T P U T
19:30:40
A N A L Y S I S C O M P L E T E
2020/05/20 19:30:40
B E G I N A N A L Y S I S
2020/05/20 19:30:41
E L E M E N T F O R M A T I O N
19:30:41
L O A D R E - S O L U T I O N
19:30:41
E L E M E N T J O I N T - F O R C E O U T P U T
19:30:41
A N A L Y S I S C O M P L E T E
2020/05/20 19:30:41
11
Simple Tech One Co., Ltd.
Analysis Result
12
Simple Tech One Co., Ltd.
Steel connections
Results
__________________________________________________________________________________________________________________________
__________________________________________________________________________________
DEMANDS
Description Pu Mu22 Mu33 Vu2 Vu3 Load type
[Kip] [Kip*ft] [Kip*ft] [Kip] [Kip]
-----------------------------------------------------------------------------------------------
DL -0.15 0.00 0.00 0.00 0.00 Design
IW -0.60 0.00 0.00 0.00 0.00 Design
WX 0.00 0.00 2.80 0.26 0.00 Design
EX 0.00 0.00 1.52 0.09 0.00 Design
D1 -1.05 0.00 0.00 0.00 0.00 Design
D2 -0.90 0.00 1.40 0.13 0.00 Design
D3 -0.90 0.00 2.80 0.26 0.00 Design
D4 -0.90 0.00 1.52 0.09 0.00 Design
D5 -0.68 0.00 2.80 0.26 0.00 Design
D6 -0.68 0.00 1.52 0.09 0.00 Design
-----------------------------------------------------------------------------------------------
Base plate
Distance from anchor to edge [in] 1.50 0.25 --
Weld size [1/16in] 3 3 -- table J2.4
wmin = wmin
= 0.0156 table J2.4
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Concrete base
Axial bearing [Kip/in2] 3.32 0.06 D3 0.02 DG1 3.1.1;
A2 = ((B/N)*Ncs)*Ncs
= ((15.75[in]/15.75[in])*39.37[in])*39.37[in]
= 1550[in2] DG1 Sec 3.1.1
A1 = B*N
= 15.75[in]*15.75[in]
= 248[in2] DG1 Sec 3.1.1
1/2
fp, max = *min(0.85*f'c*(A2/A1) , 1.7*f'c)
1/2
= 0.65*min(0.85*3000[lb/in2]*(6.25) , 1.7*3000[lb/in2])
= 3315[lb/in2] DG1 3.1.1
13
Simple Tech One Co., Ltd.
Base plate
Flexural yielding (bearing interface) [Kip*ft/ft] 1.26 0.72 D3 0.57 DG1 Eq. 3.3.13,
DG1 Sec 3.1.2
2
Mn = *Fy*tp /4
2
= 0.9*36000[lb/in2]*0.394[in] /4
= 1.26[kip*ft/ft] DG1 Eq. 3.3.13
m = m
= 5.22[in] DG1 Sec 3.1.2
n = n
= 5.22[in] DG1 Sec 3.1.2
Mpl = max(MpM, MpN)
= max(0.717[kip*ft/ft], 0.535[kip*ft/ft])
= 0.717[kip*ft/ft]
Flexural yielding (tension interface) [Kip*ft/ft] 1.26 0.85 WX 0.68 DG1 Eq. 3.3.13
2
Mn = *Fy*tp /4
2
= 0.9*36000[lb/in2]*0.394[in] /4
= 1.26[kip*ft/ft] DG1 Eq. 3.3.13
MpT = Mstrip/Beff
= 0.371[kip*ft]/5.22[in]
= 0.851[kip*ft/ft]
Column
Weld capacity [Kip/ft] 64.44 3.28 WX 0.05 p. 8-9,
Sec. J2.5,
Sec. J2.4,
HSS Manual p. 7-10
1.5
LoadAngleFactor = 1 + 0.5*(sin())
1.5
= 1 + 0.5*(sin(1.57))
= 1.5 p. 8‐9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*60000[lb/in2]*1.5
= 54000[lb/in2] Sec. J2.5
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*3/16 [in]*12[in]
= 1.59[in2] Sec. J2.4
Rw = *Fw*Aw/L
= 0.75*54000[lb/in2]*1.59[in2]/12[in]
= 5.37[kip/in]
beff = min(2*L, 5 [in])
= min(2*5.53[in], 5 [in])
= 5[in] HSS Manual p. 7‐10
Maximum weld load = T/beff
= 1.37[kip]/5[in]
= 0.273[kip/in]
14
Simple Tech One Co., Ltd.
Elastic method weld shear capacity [Kip/ft] 42.96 0.30 WX 0.01 p. 8-9,
Sec. J2.5,
Sec. J2.4
1.5
LoadAngleFactor = 1 + 0.5*(sin())
1.5
= 1 + 0.5*(sin(0))
= 1 p. 8‐9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*60000[lb/in2]*1
= 36000[lb/in2] Sec. J2.5
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*3/16 [in]*12[in]
= 1.59[in2] Sec. J2.4
Rw = *Fw*Aw/L
= 0.75*36000[lb/in2]*1.59[in2]/12[in]
= 3.58[kip/in]
fv = V/Lshear
= 0.26[kip]/10.41[in]
= 0.025[kip/in]
Elastic method weld axial capacity [Kip/ft] 64.44 11.68 WX 0.18 p. 8-9,
Sec. J2.5,
Sec. J2.4
1.5
LoadAngleFactor = 1 + 0.5*(sin())
1.5
= 1 + 0.5*(sin(1.57))
= 1.5 p. 8‐9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*60000[lb/in2]*1.5
= 54000[lb/in2] Sec. J2.5
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*3/16 [in]*12[in]
= 1.59[in2] Sec. J2.4
Rw = *Fw*Aw/L
= 0.75*54000[lb/in2]*1.59[in2]/12[in]
= 5.37[kip/in]
fa = P/L
= 0[kip]/20.81[in]
= 0[kip/in]
fb = M*c/I
= 2.8[kip*ft]*3.31[in]/114.19[in3]
= 0.974[kip/in]
f = fb + fa
= 0.974[kip/in] + 0[kip/in]
= 0.974[kip/in]
Ratio 0.68
15
Simple Tech One Co., Ltd.
Design for minor axis
Base plate (AISC 360-10 LRFD)
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Base plate
Distance from anchor to edge [in] 1.50 0.25 --
Weld size [1/16in] 3 3 -- table J2.4
wmin = wmin
= 0.0156 table J2.4
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Concrete base
Axial bearing [Kip/in2] 3.32 0.00 D1 0.00 DG1 3.1.1;
A2 = ((B/N)*Ncs)*Ncs
= ((15.75[in]/15.75[in])*39.37[in])*39.37[in]
= 1550[in2] DG1 Sec 3.1.1
A1 = B*N
= 15.75[in]*15.75[in]
= 248[in2] DG1 Sec 3.1.1
1/2
fp, max = *min(0.85*f'c*(A2/A1) , 1.7*f'c)
1/2
= 0.65*min(0.85*3000[lb/in2]*(6.25) , 1.7*3000[lb/in2])
= 3315[lb/in2] DG1 3.1.1
Base plate
Flexural yielding (bearing interface) [Kip*ft/ft] 1.26 0.06 D1 0.05 DG1 Sec 3.1.2
2
Mn = *Fy*tp /4
2
= 0.9*36000[lb/in2]*0.394[in] /4
= 1.26[kip*ft/ft] DG1 Eq. 3.3.13
A2 = ((B/N)*Ncs)*Ncs
= ((15.75[in]/15.75[in])*39.37[in])*39.37[in]
= 1550[in2] DG1 Sec 3.1.1
A1 = B*N
= 15.75[in]*15.75[in]
= 248[in2] DG1 Sec 3.1.1
m = (N ‐ 0.8*D)/2
= (15.75[in] ‐ 0.8*6.63[in])/2
= 5.22[in] DG1 Sec 3.1.3
n = (B ‐ 0.8*D)/2
= (15.75[in] ‐ 0.8*6.63[in])/2
= 5.22[in] DG1 Sec 3.1.3
1/2
Pp = min(0.85*f'c*A1*(A2/A1) , 1.7*f'c*A1)
1/2
= min(0.85*3000[lb/in2]*248[in2]*(6.25) , 1.7*3000[lb/in2]*248[in2])
= 1264.8[kip] Eq. J8‐2
2
X = (4*dc*bc/(dc + bc) )*P/(*Pp)
2
= (4*6.63[in]*6.63[in]/(6.63[in] + 6.63[in]) )*1.05[kip]/(0.65*1264.8[kip])
= 0.001277 DG1 Sec 3.1.2
16
Simple Tech One Co., Ltd.
1/2 1/2
= min(2*(X) /(1 + (1 ‐ X) ), 1.0)
1/2 1/2
= min(2*(0.001277) /(1 + (1 ‐ 0.001277) ), 1.0)
= 0.0357 DG1 Sec 3.1.2
1/2
n' = *(dc*bc) /4
1/2
= 0.0357*(6.63[in]*6.63[in]) /4
= 0.0592[in] DG1 Sec 3.1.2
l = max(m, n, n')
= max(5.22[in], 5.22[in], 0.0592[in])
= 5.22[in] DG1 Sec 3.1.2
fp = P/(B*N)
= 1.05[kip]/(15.75[in]*15.75[in])
= 4.23[lb/in2] DG1 Sec 3.1.2
2
Mpl = fp*(l /2)
2
= 4.23[lb/in2]*(5.22[in] /2)
= 0.0578[kip*ft/ft] DG1 Sec 3.1.2
Flexural yielding (tension interface) [Kip*ft/ft] 1.26 0.00 DL 0.00 DG1 Eq. 3.3.13
2
Mn = *Fy*tp /4
2
= 0.9*36000[lb/in2]*0.394[in] /4
= 1.26[kip*ft/ft] DG1 Eq. 3.3.13
MpT = Mstrip/Beff
= 0[kip*ft]/5.22[in]
= 0[kip*ft/ft]
Column
Weld capacity [Kip/ft] 64.44 0.00 DL 0.00 p. 8-9,
Sec. J2.5,
Sec. J2.4
1.5
LoadAngleFactor = 1 + 0.5*(sin())
1.5
= 1 + 0.5*(sin(1.57))
= 1.5 p. 8‐9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*60000[lb/in2]*1.5
= 54000[lb/in2] Sec. J2.5
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*3/16 [in]*12[in]
= 1.59[in2] Sec. J2.4
Rw = *Fw*Aw/L
= 0.75*54000[lb/in2]*1.59[in2]/12[in]
= 5.37[kip/in]
Elastic method weld shear capacity [Kip/ft] 42.96 0.00 DL 0.00 p. 8-9,
Sec. J2.5,
Sec. J2.4
1.5
LoadAngleFactor = 1 + 0.5*(sin())
1.5
= 1 + 0.5*(sin(0))
= 1 p. 8‐9
17
Simple Tech One Co., Ltd.
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*60000[lb/in2]*1
= 36000[lb/in2] Sec. J2.5
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*3/16 [in]*12[in]
= 1.59[in2] Sec. J2.4
Rw = *Fw*Aw/L
= 0.75*36000[lb/in2]*1.59[in2]/12[in]
= 3.58[kip/in]
fv = V/Lshear
= 0[kip]/10.41[in]
= 0[kip/in]
Elastic method weld axial capacity [Kip/ft] 64.44 0.00 DL 0.00 p. 8-9,
Sec. J2.5,
Sec. J2.4
1.5
LoadAngleFactor = 1 + 0.5*(sin())
1.5
= 1 + 0.5*(sin(1.57))
= 1.5 p. 8‐9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*60000[lb/in2]*1.5
= 54000[lb/in2] Sec. J2.5
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*3/16 [in]*12[in]
= 1.59[in2] Sec. J2.4
Rw = *Fw*Aw/L
= 0.75*54000[lb/in2]*1.59[in2]/12[in]
= 5.37[kip/in]
fa = P/L
= 0[kip]/20.81[in]
= 0[kip/in]
fb = M*c/I
= 0[kip*ft]*3.31[in]/114.19[in3]
= 0[kip/in]
f = fb + fa
= 0[kip/in] + 0[kip/in]
= 0[kip/in]
Ratio 0.05
Major axis
Anchors
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Anchors
Anchor spacing [in] 11.81 3.78 -- Sec. D.8.1
smin = 4*da
18
Simple Tech One Co., Ltd.
= 4*0.945[in]
= 3.78[in] Sec. D.8.1
Cover = 3 [in] Sec. 7.7.1
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
futa = min(futa, 1.9*fya, 125 [ksi])
= min(58000[lb/in2], 1.9*36000[lb/in2], 125 [ksi])
= 58000[lb/in2] Sec. D.5.1.2
Nsa = *Ase,N*futa
= 0.75*0.547[in2]*58000[lb/in2]
= 23.8[kip] Eq. D‐2
ca1Left = ca1Left
= 13.78[in] Sec. D.5.2.1
ca1Right<1.5*hef25.59[in]<1.5*23.62[in]True
ca1Right = ca1Right
= 25.59[in] Sec. D.5.2.1
ca2Top<1.5*hef13.78[in]<1.5*23.62[in]True
ca2Top = ca2Top
= 13.78[in] Sec. D.5.2.1
ca2Bot<1.5*hef25.59[in]<1.5*23.62[in]True
ca2Bot = ca2Bot
= 25.59[in] Sec. D.5.2.1
IsCloseToThreeEdgesTrue
hef = camax/1.5
= 25.59[in]/1.5
= 17.06[in] Sec. D.5.2.3
ca1Left<1.5*hef13.78[in]<1.5*17.06[in]True
19
Simple Tech One Co., Ltd.
ca1Left = ca1Left
= 13.78[in] Sec. D.5.2.1
ca1Right<1.5*hef25.59[in]<1.5*17.06[in]False
ca1Right = 1.5*hef
= 1.5*17.06[in]
= 25.59[in] Sec. D.5.2.1
ca2Top<1.5*hef13.78[in]<1.5*17.06[in]True
ca2Top = ca2Top
= 13.78[in] Sec. D.5.2.1
ca2Bot<1.5*hef25.59[in]<1.5*17.06[in]False
ca2Bot = 1.5*hef
= 1.5*17.06[in]
= 25.59[in] Sec. D.5.2.1
ANc = (ca1Left + ca1Right)*(ca2Top + ca2Bot)
= (13.78[in] + 25.59[in])*(13.78[in] + 25.59[in])
= 1550[in2] Sec. RD.5.2.1
2
ANco = 9*hef
2
= 9*17.06[in]
= 2619.51[in2] Eq. D‐5
ca,min<1.5*hef13.78[in]<1.5*17.06[in]True
ed,N = 0.7 + 0.3*ca,min/(1.5*hef)
= 0.7 + 0.3*13.78[in]/(1.5*17.06[in])
= 0.862 Eq. D‐10
CrackedConcreteFalse
c,N = 1.25 Sec. D.5.2.6
IsCastInPlaceAnchorTrue
cp,N = 1 Sec. D.5.2.7
IsCastInPlaceAnchorTrue
kc = 24 Sec. D.5.2.2
(IsCastInPlaceAnchor) and (IsHeadedBolt) and (hef>=11 [in]) and (hef<=25 [in])(True) and (False) and (17.06[in]> = 11 [in]) and (17.06[in]<
= 25 [in])False
1/2 1.5
Nb = kc*a*(fc/(1 [psi])) *(hef/(1 [in])) [lb]
1/2 1.5
= 24*1*(3000[lb/in2]/(1 [psi])) *(17.06[in]/(1 [in])) [lb]
= 92.63[kip] Eq. D‐6
Ncb = (ANc/ANco)*ed,N*c,N*cp,N*Nb
= (1550[in2]/2619.51[in2])*0.862*1.25*1*92.63[kip]
= 59.03[kip] Eq. D‐3
20
Simple Tech One Co., Ltd.
HighSeismicDesignCategoryFalse
Ncb = *Ncb
= 0.7*59.03[kip]
= 41.32[kip] Sec. D.3.3.4.4
Breakout of group of anchors in tension [Kip] 41.32 2.73 WX 0.07 Eq. D-4,
Sec. D.3.3.4.4
2
ANco = 9*hef
2
= 9*17.06[in]
= 2619.51[in2] Eq. D‐5
ANc = min(ANc, n*ANco)
= min(1550[in2], 2*2619.51[in2])
= 1550[in2] Sec. D.5.2.1
ec,Ny = min(1/(1 + 2*e'N/(3*hef)), 1)
= min(1/(1 + 2*0[in]/(3*17.06[in])), 1)
= 1 Eq. D‐8
ec,Nx = min(1/(1 + 2*e'N/(3*hef)), 1)
= min(1/(1 + 2*0[in]/(3*17.06[in])), 1)
= 1 Eq. D‐8
ec,N = ec,Nx*ec,Ny
= 1*1
= 1 Eq. D‐8
ca,min<1.5*hef13.78[in]<1.5*17.06[in]True
ed,N = 0.7 + 0.3*ca,min/(1.5*hef)
= 0.7 + 0.3*13.78[in]/(1.5*17.06[in])
= 0.862 Eq. D‐10
CrackedConcreteFalse
c,N = 1.25 Sec. D.5.2.6
IsCastInPlaceAnchorTrue
cp,N = 1 Sec. D.5.2.7
IsCastInPlaceAnchorTrue
kc = 24 Sec. D.5.2.2
(IsCastInPlaceAnchor) and (IsHeadedBolt) and (hef>=11 [in]) and (hef<=25 [in])(True) and (False) and (17.06[in]> = 11 [in]) and (17.06[in]<
= 25 [in])False
1/2 1.5
Nb = kc*a*(fc/(1 [psi])) *(hef/(1 [in])) [lb]
1/2 1.5
= 24*1*(3000[lb/in2]/(1 [psi])) *(17.06[in]/(1 [in])) [lb]
= 92.63[kip] Eq. D‐6
Ncbg = (ANc/ANco)*ec,N*ed,N*c,N*cp,N*Nb
= (1550[in2]/2619.51[in2])*1*0.862*1.25*1*92.63[kip]
= 59.03[kip] Eq. D‐4
21
Simple Tech One Co., Ltd.
HighSeismicDesignCategoryFalse
Ncbg = *Ncbg
= 0.7*59.03[kip]
= 41.32[kip] Sec. D.3.3.4.4
Np = 0.9*fc*eh*da
= 0.9*3000[lb/in2]*4.25[in]*0.945[in]
= 10.85[kip] Eq. D‐15
CrackedConcreteFalse
c,P = 1.4 Sec. D.5.3.6
Npn = c,P*Np
= 1.4*10.85[kip]
= 15.19[kip] Eq. D‐13
HighSeismicDesignCategoryFalse
Npn = *Npn
= 0.7*15.19[kip]
= 10.63[kip] Sec. D.3.3.4.4
futa = min(futa, 1.9*fya, 125 [ksi])
= min(58000[lb/in2], 1.9*36000[lb/in2], 125 [ksi])
= 58000[lb/in2] Sec. D.5.1.2
HasGroutPadFalse
Vsa = *0.6*n*Ase,V*futa
= 0.65*0.6*1*0.547[in2]*58000[lb/in2]
= 12.38[kip] Eq. D‐29
ca2Left = ca2Left
= 13.78[in] Sec. D.6.2.1
ca2Right<1.5*ca125.59[in]<1.5*13.78[in]False
ca2Right = 1.5*ca1
= 1.5*13.78[in]
= 20.67[in] Sec. D.5.2.1
ha<1.5*ca139.37[in]<1.5*13.78[in]False
22
Simple Tech One Co., Ltd.
ha = 1.5*ca1
= 1.5*13.78[in]
= 20.67[in] Sec. D.5.2.1
IsCloseToThreeEdgesFalse
ca1 = ca1
= 13.78[in] Sec. D.6.2.4
LVc = ca2Left + ca2Right
= 13.78[in] + 20.67[in]
= 34.45[in] Sec. RD.6.2.1
AVc = LVc*min(ha, 1.5*ca1)
= 34.45[in]*min(39.37[in], 1.5*13.78[in])
= 712.03[in2] Sec. RD.6.2.1
2
AVco = 4.5*ca1
2
= 4.5*13.78[in]
= 854.44[in2] Eq. D‐32
ca2<1.5*ca113.78[in]<1.5*13.78[in]True
ed,V = 0.7 + 0.3*(ca2/(1.5*ca1))
= 0.7 + 0.3*(13.78[in]/(1.5*13.78[in]))
= 0.9 Eq. D‐28
CrackedConcreteFalse
c,V = 1.4 Sec. D.6.2.7
ha<1.5*ca139.37[in]<1.5*13.78[in]False
h,V = 1 Sec. D.6.2.8
le = min(hef, 8*da)
= min(23.62[in], 8*0.945[in])
= 7.56[in] Sec. D.6.2.2
0.2 1/2 1/2 1.5 1/2 1.5
Vb = min((7*(le/da) *(da/(1 [in])) )*a*(fc/(1 [psi])) *(ca1/(1 [in])) [lb], 9*a*(fc/(1 [psi])) *(ca1/(1 [in])) [lb])
0.2 1/2 1/2
= min((7*(7.56[in]/0.945[in]) *(0.945[in]/(1 [in])) )*1*(3000[lb/in2]/(1 [psi])) *(13.78[in]/
1.5 1/2 1.5
(1 [in])) [lb], 9*1*(3000[lb/in2]/(1 [psi])) *(13.78[in]/(1 [in])) [lb])
= 25.21[kip] Eq. D‐33, D‐34
Vcb = (AVc/AVco)*ed,V*c,V*h,V*Vb
= (712.03[in2]/854.44[in2])*0.9*1.4*1*25.21[kip]
= 26.48[kip] Eq. D‐30
Vcb = *Vcb
= 0.7*26.48[kip]
= 18.53[kip] Table D.4.1.1,
Sec. D.4.3
23
Simple Tech One Co., Ltd.
Breakout of group of anchors in shear [Kip] 21.18 0.26 WX 0.01 Table D.4.1.1,
Sec. D.4.3
2
AVco = 4.5*ca1
2
= 4.5*13.78[in]
= 854.44[in2] Eq. D‐32
AVc = LVc*min(ha, 1.5*ca1)
= 39.37[in]*min(39.37[in], 1.5*13.78[in])
= 813.75[in2] Sec. RD.6.2.1
AVc = min(AVc, n*AVco)
= min(813.75[in2], 2*854.44[in2])
= 813.75[in2] Sec. RD.6.2.1
ec,V = min(1/(1 + 2*e'V/(3*ca1)), 1)
= min(1/(1 + 2*0[in]/(3*13.78[in])), 1)
= 1 Eq. D‐36
ca2<1.5*ca113.78[in]<1.5*13.78[in]True
ed,V = 0.7 + 0.3*(ca2/(1.5*ca1))
= 0.7 + 0.3*(13.78[in]/(1.5*13.78[in]))
= 0.9 Eq. D‐28
CrackedConcreteFalse
c,V = 1.4 Sec. D.6.2.7
ha<1.5*ca139.37[in]<1.5*13.78[in]False
h,V = 1 Sec. D.6.2.8
le = min(hef, 8*da)
= min(23.62[in], 8*0.945[in])
= 7.56[in] Sec. D.6.2.2
0.2 1/2 1/2 1.5 1/2 1.5
Vb = min((7*(le/da) *(da/(1 [in])) )*a*(fc/(1 [psi])) *(ca1/(1 [in])) [lb], 9*a*(fc/(1 [psi])) *(ca1/(1 [in])) [lb])
0.2 1/2 1/2
= min((7*(7.56[in]/0.945[in]) *(0.945[in]/(1 [in])) )*1*(3000[lb/in2]/(1 [psi])) *(13.78[in]/
1.5 1/2 1.5
(1 [in])) [lb], 9*1*(3000[lb/in2]/(1 [psi])) *(13.78[in]/(1 [in])) [lb])
= 25.21[kip] Eq. D‐33, D‐34
Vcbg = (AVc/AVco)*ec,V*ed,V*c,V*h,V*Vb
= (813.75[in2]/854.44[in2])*1*0.9*1.4*1*25.21[kip]
= 30.26[kip] Eq. D‐31
Vcbg = *Vcbg
= 0.7*30.26[kip]
= 21.18[kip] Table D.4.1.1,
Sec. D.4.3
kcp = 2 Sec. D.6.3.1
24
Simple Tech One Co., Ltd.
ca1Left<1.5*hef13.78[in]<1.5*23.62[in]True
ca1Left = ca1Left
= 13.78[in] Sec. D.5.2.1
ca1Right<1.5*hef25.59[in]<1.5*23.62[in]True
ca1Right = ca1Right
= 25.59[in] Sec. D.5.2.1
ca2Top<1.5*hef13.78[in]<1.5*23.62[in]True
ca2Top = ca2Top
= 13.78[in] Sec. D.5.2.1
ca2Bot<1.5*hef25.59[in]<1.5*23.62[in]True
ca2Bot = ca2Bot
= 25.59[in] Sec. D.5.2.1
IsCloseToThreeEdgesTrue
hef = camax/1.5
= 25.59[in]/1.5
= 17.06[in] Sec. D.5.2.3
ca1Left<1.5*hef13.78[in]<1.5*17.06[in]True
ca1Left = ca1Left
= 13.78[in] Sec. D.5.2.1
ca1Right<1.5*hef25.59[in]<1.5*17.06[in]False
ca1Right = 1.5*hef
= 1.5*17.06[in]
= 25.59[in] Sec. D.5.2.1
ca2Top<1.5*hef13.78[in]<1.5*17.06[in]True
ca2Top = ca2Top
= 13.78[in] Sec. D.5.2.1
ca2Bot<1.5*hef25.59[in]<1.5*17.06[in]False
ca2Bot = 1.5*hef
= 1.5*17.06[in]
= 25.59[in] Sec. D.5.2.1
ANc = (ca1Left + ca1Right)*(ca2Top + ca2Bot)
= (13.78[in] + 25.59[in])*(13.78[in] + 25.59[in])
= 1550[in2] Sec. RD.5.2.1
2
ANco = 9*hef
2
= 9*17.06[in]
= 2619.51[in2] Eq. D‐5
ca,min<1.5*hef13.78[in]<1.5*17.06[in]True
25
Simple Tech One Co., Ltd.
ed,N = 0.7 + 0.3*ca,min/(1.5*hef)
= 0.7 + 0.3*13.78[in]/(1.5*17.06[in])
= 0.862 Eq. D‐10
CrackedConcreteFalse
c,N = 1.25 Sec. D.5.2.6
IsCastInPlaceAnchorTrue
cp,N = 1 Sec. D.5.2.7
IsCastInPlaceAnchorTrue
kc = 24 Sec. D.5.2.2
(IsCastInPlaceAnchor) and (IsHeadedBolt) and (hef>=11 [in]) and (hef<=25 [in])(True) and (False) and (17.06[in]> = 11 [in]) and (17.06[in]<
= 25 [in])False
1/2 1.5
Nb = kc*a*(fc/(1 [psi])) *(hef/(1 [in])) [lb]
1/2 1.5
= 24*1*(3000[lb/in2]/(1 [psi])) *(17.06[in]/(1 [in])) [lb]
= 92.63[kip] Eq. D‐6
Ncb = (ANc/ANco)*ed,N*c,N*cp,N*Nb
= (1550[in2]/2619.51[in2])*0.862*1.25*1*92.63[kip]
= 59.03[kip] Eq. D‐3
Vcp = kcp*Ncb
= 2*59.03[kip]
= 118.05[kip] Eq. D‐40
Vcp = *Vcp
= 0.7*118.05[kip]
= 82.64[kip] Table D.4.1.1,
Sec. D.4.3
Pryout of group of anchors in shear [Kip] 82.64 0.13 WX 0.00 Eq. D-4,
Table D.4.1.1,
Sec. D.4.3
hef<2.5 [in]23.62[in]<2.5 [in]False
kcp = 2 Sec. D.6.3.1
2
ANco = 9*hef
2
= 9*17.06[in]
= 2619.51[in2] Eq. D‐5
ANc = min(ANc, n*ANco)
= min(1550[in2], 2*2619.51[in2])
= 1550[in2] Sec. D.5.2.1
ec,Ny = min(1/(1 + 2*e'N/(3*hef)), 1)
= min(1/(1 + 2*0[in]/(3*17.06[in])), 1)
= 1 Eq. D‐8
26
Simple Tech One Co., Ltd.
ec,Nx = min(1/(1 + 2*e'N/(3*hef)), 1)
= min(1/(1 + 2*0[in]/(3*17.06[in])), 1)
= 1 Eq. D‐8
ec,N = ec,Nx*ec,Ny
= 1*1
= 1 Eq. D‐8
ca,min<1.5*hef13.78[in]<1.5*17.06[in]True
ed,N = 0.7 + 0.3*ca,min/(1.5*hef)
= 0.7 + 0.3*13.78[in]/(1.5*17.06[in])
= 0.862 Eq. D‐10
CrackedConcreteFalse
c,N = 1.25 Sec. D.5.2.6
IsCastInPlaceAnchorTrue
cp,N = 1 Sec. D.5.2.7
IsCastInPlaceAnchorTrue
kc = 24 Sec. D.5.2.2
(IsCastInPlaceAnchor) and (IsHeadedBolt) and (hef>=11 [in]) and (hef<=25 [in])(True) and (False) and (17.06[in]> = 11 [in]) and (17.06[in]<
= 25 [in])False
1/2 1.5
Nb = kc*a*(fc/(1 [psi])) *(hef/(1 [in])) [lb]
1/2 1.5
= 24*1*(3000[lb/in2]/(1 [psi])) *(17.06[in]/(1 [in])) [lb]
= 92.63[kip] Eq. D‐6
Ncbg = (ANc/ANco)*ec,N*ed,N*c,N*cp,N*Nb
= (1550[in2]/2619.51[in2])*1*0.862*1.25*1*92.63[kip]
= 59.03[kip] Eq. D‐4
Vcpg = kcp*Ncbg
= 2*59.03[kip]
= 118.05[kip] Eq. D‐41
Vcpg = *Vcpg
= 0.7*118.05[kip]
= 82.64[kip] Table D.4.1.1,
Sec. D.4.3
Interaction of tensile and shear forces [Kip] 1.20 0.00 WX 0.00 Eq. D-2,
Eq. D-3,
Sec. D.3.3.4.4,
Eq. D-4,
Eq. D-29,
Table D.4.1.1,
Sec. D.4.3,
Sec. D.7
2
Ase = π/4.0*(da ‐ 0.9743 [in]/nt)
2
= π/4.0*(0.945[in] ‐ 0.9743 [in]/8.84)
= 0.547[in2] Sec. D.5.1.1,
D.6.1.2
27
Simple Tech One Co., Ltd.
futa = min(futa, 1.9*fya, 125 [ksi])
= min(58000[lb/in2], 1.9*36000[lb/in2], 125 [ksi])
= 58000[lb/in2] Sec. D.5.1.2
Nsa = *Ase,N*futa
= 0.75*0.547[in2]*58000[lb/in2]
= 23.8[kip] Eq. D‐2
ca1Left<1.5*hef13.78[in]<1.5*23.62[in]True
ca1Left = ca1Left
= 13.78[in] Sec. D.5.2.1
ca1Right<1.5*hef25.59[in]<1.5*23.62[in]True
ca1Right = ca1Right
= 25.59[in] Sec. D.5.2.1
ca2Top<1.5*hef13.78[in]<1.5*23.62[in]True
ca2Top = ca2Top
= 13.78[in] Sec. D.5.2.1
ca2Bot<1.5*hef25.59[in]<1.5*23.62[in]True
ca2Bot = ca2Bot
= 25.59[in] Sec. D.5.2.1
IsCloseToThreeEdgesTrue
hef = camax/1.5
= 25.59[in]/1.5
= 17.06[in] Sec. D.5.2.3
ca1Left<1.5*hef13.78[in]<1.5*17.06[in]True
ca1Left = ca1Left
= 13.78[in] Sec. D.5.2.1
ca1Right<1.5*hef25.59[in]<1.5*17.06[in]False
ca1Right = 1.5*hef
= 1.5*17.06[in]
= 25.59[in] Sec. D.5.2.1
ca2Top<1.5*hef13.78[in]<1.5*17.06[in]True
ca2Top = ca2Top
= 13.78[in] Sec. D.5.2.1
ca2Bot<1.5*hef25.59[in]<1.5*17.06[in]False
ca2Bot = 1.5*hef
= 1.5*17.06[in]
= 25.59[in] Sec. D.5.2.1
28
Simple Tech One Co., Ltd.
ANc = (ca1Left + ca1Right)*(ca2Top + ca2Bot)
= (13.78[in] + 25.59[in])*(13.78[in] + 25.59[in])
= 1550[in2] Sec. RD.5.2.1
2
ANco = 9*hef
2
= 9*17.06[in]
= 2619.51[in2] Eq. D‐5
ca,min<1.5*hef13.78[in]<1.5*17.06[in]True
ed,N = 0.7 + 0.3*ca,min/(1.5*hef)
= 0.7 + 0.3*13.78[in]/(1.5*17.06[in])
= 0.862 Eq. D‐10
CrackedConcreteFalse
c,N = 1.25 Sec. D.5.2.6
IsCastInPlaceAnchorTrue
cp,N = 1 Sec. D.5.2.7
IsCastInPlaceAnchorTrue
kc = 24 Sec. D.5.2.2
(IsCastInPlaceAnchor) and (IsHeadedBolt) and (hef>=11 [in]) and (hef<=25 [in])(True) and (False) and (17.06[in]> = 11 [in]) and (17.06[in]<
= 25 [in])False
1/2 1.5
Nb = kc*a*(fc/(1 [psi])) *(hef/(1 [in])) [lb]
1/2 1.5
= 24*1*(3000[lb/in2]/(1 [psi])) *(17.06[in]/(1 [in])) [lb]
= 92.63[kip] Eq. D‐6
Ncb = (ANc/ANco)*ed,N*c,N*cp,N*Nb
= (1550[in2]/2619.51[in2])*0.862*1.25*1*92.63[kip]
= 59.03[kip] Eq. D‐3
HighSeismicDesignCategoryFalse
Ncb = *Ncb
= 0.7*59.03[kip]
= 41.32[kip] Sec. D.3.3.4.4
2
ANco = 9*hef
2
= 9*17.06[in]
= 2619.51[in2] Eq. D‐5
ANc = min(ANc, n*ANco)
= min(1550[in2], 2*2619.51[in2])
= 1550[in2] Sec. D.5.2.1
ec,Ny = min(1/(1 + 2*e'N/(3*hef)), 1)
= min(1/(1 + 2*0[in]/(3*17.06[in])), 1)
= 1 Eq. D‐8
29
Simple Tech One Co., Ltd.
ec,Nx = min(1/(1 + 2*e'N/(3*hef)), 1)
= min(1/(1 + 2*0[in]/(3*17.06[in])), 1)
= 1 Eq. D‐8
ec,N = ec,Nx*ec,Ny
= 1*1
= 1 Eq. D‐8
ca,min<1.5*hef13.78[in]<1.5*17.06[in]True
ed,N = 0.7 + 0.3*ca,min/(1.5*hef)
= 0.7 + 0.3*13.78[in]/(1.5*17.06[in])
= 0.862 Eq. D‐10
CrackedConcreteFalse
c,N = 1.25 Sec. D.5.2.6
IsCastInPlaceAnchorTrue
cp,N = 1 Sec. D.5.2.7
IsCastInPlaceAnchorTrue
kc = 24 Sec. D.5.2.2
(IsCastInPlaceAnchor) and (IsHeadedBolt) and (hef>=11 [in]) and (hef<=25 [in])(True) and (False) and (17.06[in]> = 11 [in]) and (17.06[in]<
= 25 [in])False
1/2 1.5
Nb = kc*a*(fc/(1 [psi])) *(hef/(1 [in])) [lb]
1/2 1.5
= 24*1*(3000[lb/in2]/(1 [psi])) *(17.06[in]/(1 [in])) [lb]
= 92.63[kip] Eq. D‐6
Ncbg = (ANc/ANco)*ec,N*ed,N*c,N*cp,N*Nb
= (1550[in2]/2619.51[in2])*1*0.862*1.25*1*92.63[kip]
= 59.03[kip] Eq. D‐4
HighSeismicDesignCategoryFalse
Ncbg = *Ncbg
= 0.7*59.03[kip]
= 41.32[kip] Sec. D.3.3.4.4
IsHeadedBoltFalse
Np = 0.9*fc*eh*da
= 0.9*3000[lb/in2]*4.25[in]*0.945[in]
= 10.85[kip] Eq. D‐15
CrackedConcreteFalse
c,P = 1.4 Sec. D.5.3.6
Npn = c,P*Np
= 1.4*10.85[kip]
= 15.19[kip] Eq. D‐13
30
Simple Tech One Co., Ltd.
HighSeismicDesignCategoryFalse
Npn = *Npn
= 0.7*15.19[kip]
= 10.63[kip] Sec. D.3.3.4.4
2
Ase = π/4.0*(da ‐ 0.9743 [in]/nt)
2
= π/4.0*(0.945[in] ‐ 0.9743 [in]/8.84)
= 0.547[in2] Sec. D.5.1.1,
D.6.1.2
futa = min(futa, 1.9*fya, 125 [ksi])
= min(58000[lb/in2], 1.9*36000[lb/in2], 125 [ksi])
= 58000[lb/in2] Sec. D.5.1.2
HasGroutPadFalse
Vsa = *0.6*n*Ase,V*futa
= 0.65*0.6*1*0.547[in2]*58000[lb/in2]
= 12.38[kip] Eq. D‐29
ca2Left<1.5*ca113.78[in]<1.5*13.78[in]True
ca2Left = ca2Left
= 13.78[in] Sec. D.6.2.1
ca2Right<1.5*ca125.59[in]<1.5*13.78[in]False
ca2Right = 1.5*ca1
= 1.5*13.78[in]
= 20.67[in] Sec. D.5.2.1
ha<1.5*ca139.37[in]<1.5*13.78[in]False
ha = 1.5*ca1
= 1.5*13.78[in]
= 20.67[in] Sec. D.5.2.1
IsCloseToThreeEdgesFalse
ca1 = ca1
= 13.78[in] Sec. D.6.2.4
LVc = ca2Left + ca2Right
= 13.78[in] + 20.67[in]
= 34.45[in] Sec. RD.6.2.1
AVc = LVc*min(ha, 1.5*ca1)
= 34.45[in]*min(39.37[in], 1.5*13.78[in])
= 712.03[in2] Sec. RD.6.2.1
2
AVco = 4.5*ca1
2
= 4.5*13.78[in]
= 854.44[in2] Eq. D‐32
ca2<1.5*ca113.78[in]<1.5*13.78[in]True
31
Simple Tech One Co., Ltd.
ed,V = 0.7 + 0.3*(ca2/(1.5*ca1))
= 0.7 + 0.3*(13.78[in]/(1.5*13.78[in]))
= 0.9 Eq. D‐28
CrackedConcreteFalse
c,V = 1.4 Sec. D.6.2.7
ha<1.5*ca139.37[in]<1.5*13.78[in]False
h,V = 1 Sec. D.6.2.8
le = min(hef, 8*da)
= min(23.62[in], 8*0.945[in])
= 7.56[in] Sec. D.6.2.2
0.2 1/2 1/2 1.5 1/2 1.5
Vb = min((7*(le/da) *(da/(1 [in])) )*a*(fc/(1 [psi])) *(ca1/(1 [in])) [lb], 9*a*(fc/(1 [psi])) *(ca1/(1 [in])) [lb])
0.2 1/2 1/2
= min((7*(7.56[in]/0.945[in]) *(0.945[in]/(1 [in])) )*1*(3000[lb/in2]/(1 [psi])) *(13.78[in]/
1.5 1/2 1.5
(1 [in])) [lb], 9*1*(3000[lb/in2]/(1 [psi])) *(13.78[in]/(1 [in])) [lb])
= 25.21[kip] Eq. D‐33, D‐34
Vcb = (AVc/AVco)*ed,V*c,V*h,V*Vb
= (712.03[in2]/854.44[in2])*0.9*1.4*1*25.21[kip]
= 26.48[kip] Eq. D‐30
Vcb = *Vcb
= 0.7*26.48[kip]
= 18.53[kip] Table D.4.1.1,
Sec. D.4.3
2
AVco = 4.5*ca1
2
= 4.5*13.78[in]
= 854.44[in2] Eq. D‐32
AVc = LVc*min(ha, 1.5*ca1)
= 39.37[in]*min(39.37[in], 1.5*13.78[in])
= 813.75[in2] Sec. RD.6.2.1
AVc = min(AVc, n*AVco)
= min(813.75[in2], 2*854.44[in2])
= 813.75[in2] Sec. RD.6.2.1
ec,V = min(1/(1 + 2*e'V/(3*ca1)), 1)
= min(1/(1 + 2*0[in]/(3*13.78[in])), 1)
= 1 Eq. D‐36
ca2<1.5*ca113.78[in]<1.5*13.78[in]True
ed,V = 0.7 + 0.3*(ca2/(1.5*ca1))
= 0.7 + 0.3*(13.78[in]/(1.5*13.78[in]))
= 0.9 Eq. D‐28
CrackedConcreteFalse
c,V = 1.4 Sec. D.6.2.7
32
Simple Tech One Co., Ltd.
ha<1.5*ca139.37[in]<1.5*13.78[in]False
h,V = 1 Sec. D.6.2.8
le = min(hef, 8*da)
= min(23.62[in], 8*0.945[in])
= 7.56[in] Sec. D.6.2.2
0.2 1/2 1/2 1.5 1/2 1.5
Vb = min((7*(le/da) *(da/(1 [in])) )*a*(fc/(1 [psi])) *(ca1/(1 [in])) [lb], 9*a*(fc/(1 [psi])) *(ca1/(1 [in])) [lb])
0.2 1/2 1/2
= min((7*(7.56[in]/0.945[in]) *(0.945[in]/(1 [in])) )*1*(3000[lb/in2]/(1 [psi])) *(13.78[in]/
1.5 1/2 1.5
(1 [in])) [lb], 9*1*(3000[lb/in2]/(1 [psi])) *(13.78[in]/(1 [in])) [lb])
= 25.21[kip] Eq. D‐33, D‐34
Vcbg = (AVc/AVco)*ec,V*ed,V*c,V*h,V*Vb
= (813.75[in2]/854.44[in2])*1*0.9*1.4*1*25.21[kip]
= 30.26[kip] Eq. D‐31
Vcbg = *Vcbg
= 0.7*30.26[kip]
= 21.18[kip] Table D.4.1.1,
Sec. D.4.3
hef<2.5 [in]23.62[in]<2.5 [in]False
kcp = 2 Sec. D.6.3.1
ca1Left<1.5*hef13.78[in]<1.5*23.62[in]True
ca1Left = ca1Left
= 13.78[in] Sec. D.5.2.1
ca1Right<1.5*hef25.59[in]<1.5*23.62[in]True
ca1Right = ca1Right
= 25.59[in] Sec. D.5.2.1
ca2Top<1.5*hef13.78[in]<1.5*23.62[in]True
ca2Top = ca2Top
= 13.78[in] Sec. D.5.2.1
ca2Bot<1.5*hef25.59[in]<1.5*23.62[in]True
ca2Bot = ca2Bot
= 25.59[in] Sec. D.5.2.1
IsCloseToThreeEdgesTrue
hef = camax/1.5
= 25.59[in]/1.5
= 17.06[in] Sec. D.5.2.3
ca1Left<1.5*hef13.78[in]<1.5*17.06[in]True
ca1Left = ca1Left
= 13.78[in] Sec. D.5.2.1
33
Simple Tech One Co., Ltd.
ca1Right<1.5*hef25.59[in]<1.5*17.06[in]False
ca1Right = 1.5*hef
= 1.5*17.06[in]
= 25.59[in] Sec. D.5.2.1
ca2Top<1.5*hef13.78[in]<1.5*17.06[in]True
ca2Top = ca2Top
= 13.78[in] Sec. D.5.2.1
ca2Bot<1.5*hef25.59[in]<1.5*17.06[in]False
ca2Bot = 1.5*hef
= 1.5*17.06[in]
= 25.59[in] Sec. D.5.2.1
ANc = (ca1Left + ca1Right)*(ca2Top + ca2Bot)
= (13.78[in] + 25.59[in])*(13.78[in] + 25.59[in])
= 1550[in2] Sec. RD.5.2.1
2
ANco = 9*hef
2
= 9*17.06[in]
= 2619.51[in2] Eq. D‐5
ca,min<1.5*hef13.78[in]<1.5*17.06[in]True
ed,N = 0.7 + 0.3*ca,min/(1.5*hef)
= 0.7 + 0.3*13.78[in]/(1.5*17.06[in])
= 0.862 Eq. D‐10
CrackedConcreteFalse
c,N = 1.25 Sec. D.5.2.6
IsCastInPlaceAnchorTrue
cp,N = 1 Sec. D.5.2.7
IsCastInPlaceAnchorTrue
kc = 24 Sec. D.5.2.2
(IsCastInPlaceAnchor) and (IsHeadedBolt) and (hef>=11 [in]) and (hef<=25 [in])(True) and (False) and (17.06[in]> = 11 [in]) and (17.06[in]<
= 25 [in])False
1/2 1.5
Nb = kc*a*(fc/(1 [psi])) *(hef/(1 [in])) [lb]
1/2 1.5
= 24*1*(3000[lb/in2]/(1 [psi])) *(17.06[in]/(1 [in])) [lb]
= 92.63[kip] Eq. D‐6
Ncb = (ANc/ANco)*ed,N*c,N*cp,N*Nb
= (1550[in2]/2619.51[in2])*0.862*1.25*1*92.63[kip]
= 59.03[kip] Eq. D‐3
34
Simple Tech One Co., Ltd.
Vcp = kcp*Ncb
= 2*59.03[kip]
= 118.05[kip] Eq. D‐40
Vcp = *Vcp
= 0.7*118.05[kip]
= 82.64[kip] Table D.4.1.1,
Sec. D.4.3
hef<2.5 [in]23.62[in]<2.5 [in]False
kcp = 2 Sec. D.6.3.1
2
ANco = 9*hef
2
= 9*17.06[in]
= 2619.51[in2] Eq. D‐5
ANc = min(ANc, n*ANco)
= min(1550[in2], 2*2619.51[in2])
= 1550[in2] Sec. D.5.2.1
ec,Ny = min(1/(1 + 2*e'N/(3*hef)), 1)
= min(1/(1 + 2*0[in]/(3*17.06[in])), 1)
= 1 Eq. D‐8
ec,Nx = min(1/(1 + 2*e'N/(3*hef)), 1)
= min(1/(1 + 2*0[in]/(3*17.06[in])), 1)
= 1 Eq. D‐8
ec,N = ec,Nx*ec,Ny
= 1*1
= 1 Eq. D‐8
ca,min<1.5*hef13.78[in]<1.5*17.06[in]True
ed,N = 0.7 + 0.3*ca,min/(1.5*hef)
= 0.7 + 0.3*13.78[in]/(1.5*17.06[in])
= 0.862 Eq. D‐10
CrackedConcreteFalse
c,N = 1.25 Sec. D.5.2.6
IsCastInPlaceAnchorTrue
cp,N = 1 Sec. D.5.2.7
IsCastInPlaceAnchorTrue
kc = 24 Sec. D.5.2.2
(IsCastInPlaceAnchor) and (IsHeadedBolt) and (hef>=11 [in]) and (hef<=25 [in])(True) and (False) and (17.06[in]> = 11 [in]) and (17.06[in]<
= 25 [in])False
35
Simple Tech One Co., Ltd.
1/2 1.5
Nb = kc*a*(fc/(1 [psi])) *(hef/(1 [in])) [lb]
1/2 1.5
= 24*1*(3000[lb/in2]/(1 [psi])) *(17.06[in]/(1 [in])) [lb]
= 92.63[kip] Eq. D‐6
Ncbg = (ANc/ANco)*ec,N*ed,N*c,N*cp,N*Nb
= (1550[in2]/2619.51[in2])*1*0.862*1.25*1*92.63[kip]
= 59.03[kip] Eq. D‐4
Vcpg = kcp*Ncbg
= 2*59.03[kip]
= 118.05[kip] Eq. D‐41
Vcpg = *Vcpg
= 0.7*118.05[kip]
= 82.64[kip] Table D.4.1.1,
Sec. D.4.3
(Nua>0.2*Nn) and (Vua>0.2*Vn)(1.37[kip]>0.2*10.63[kip]) and (0.26[kip]>0.2*21.18[kip])False
TensionShearInteraction = 0 Sec. D.7
Ratio 0.13
Minor axis
Anchors
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Anchors
Anchor spacing [in] 11.81 3.78 -- Sec. D.8.1
smin = 4*da
= 4*0.945[in]
= 3.78[in] Sec. D.8.1
Cover = 3 [in] Sec. 7.7.1
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
futa = min(futa, 1.9*fya, 125 [ksi])
= min(58000[lb/in2], 1.9*36000[lb/in2], 125 [ksi])
= 58000[lb/in2] Sec. D.5.1.2
36
Simple Tech One Co., Ltd.
Nsa = *Ase,N*futa
= 0.75*0.547[in2]*58000[lb/in2]
= 23.8[kip] Eq. D‐2
ca1Left = ca1Left
= 13.78[in] Sec. D.5.2.1
ca1Right<1.5*hef25.59[in]<1.5*23.62[in]True
ca1Right = ca1Right
= 25.59[in] Sec. D.5.2.1
ca2Top<1.5*hef13.78[in]<1.5*23.62[in]True
ca2Top = ca2Top
= 13.78[in] Sec. D.5.2.1
ca2Bot<1.5*hef25.59[in]<1.5*23.62[in]True
ca2Bot = ca2Bot
= 25.59[in] Sec. D.5.2.1
IsCloseToThreeEdgesTrue
hef = camax/1.5
= 25.59[in]/1.5
= 17.06[in] Sec. D.5.2.3
ca1Left<1.5*hef13.78[in]<1.5*17.06[in]True
ca1Left = ca1Left
= 13.78[in] Sec. D.5.2.1
ca1Right<1.5*hef25.59[in]<1.5*17.06[in]False
ca1Right = 1.5*hef
= 1.5*17.06[in]
= 25.59[in] Sec. D.5.2.1
ca2Top<1.5*hef13.78[in]<1.5*17.06[in]True
ca2Top = ca2Top
= 13.78[in] Sec. D.5.2.1
ca2Bot<1.5*hef25.59[in]<1.5*17.06[in]False
ca2Bot = 1.5*hef
= 1.5*17.06[in]
= 25.59[in] Sec. D.5.2.1
ANc = (ca1Left + ca1Right)*(ca2Top + ca2Bot)
= (13.78[in] + 25.59[in])*(13.78[in] + 25.59[in])
= 1550[in2] Sec. RD.5.2.1
37
Simple Tech One Co., Ltd.
2
ANco = 9*hef
2
= 9*17.06[in]
= 2619.51[in2] Eq. D‐5
ca,min<1.5*hef13.78[in]<1.5*17.06[in]True
ed,N = 0.7 + 0.3*ca,min/(1.5*hef)
= 0.7 + 0.3*13.78[in]/(1.5*17.06[in])
= 0.862 Eq. D‐10
CrackedConcreteFalse
c,N = 1.25 Sec. D.5.2.6
IsCastInPlaceAnchorTrue
cp,N = 1 Sec. D.5.2.7
IsCastInPlaceAnchorTrue
kc = 24 Sec. D.5.2.2
(IsCastInPlaceAnchor) and (IsHeadedBolt) and (hef>=11 [in]) and (hef<=25 [in])(True) and (False) and (17.06[in]> = 11 [in]) and (17.06[in]<
= 25 [in])False
1/2 1.5
Nb = kc*a*(fc/(1 [psi])) *(hef/(1 [in])) [lb]
1/2 1.5
= 24*1*(3000[lb/in2]/(1 [psi])) *(17.06[in]/(1 [in])) [lb]
= 92.63[kip] Eq. D‐6
Ncb = (ANc/ANco)*ed,N*c,N*cp,N*Nb
= (1550[in2]/2619.51[in2])*0.862*1.25*1*92.63[kip]
= 59.03[kip] Eq. D‐3
HighSeismicDesignCategoryFalse
Ncb = *Ncb
= 0.7*59.03[kip]
= 41.32[kip] Sec. D.3.3.4.4
Np = 0.9*fc*eh*da
= 0.9*3000[lb/in2]*4.25[in]*0.945[in]
= 10.85[kip] Eq. D‐15
CrackedConcreteFalse
c,P = 1.4 Sec. D.5.3.6
Npn = c,P*Np
= 1.4*10.85[kip]
= 15.19[kip] Eq. D‐13
HighSeismicDesignCategoryFalse
38
Simple Tech One Co., Ltd.
Npn = *Npn
= 0.7*15.19[kip]
= 10.63[kip] Sec. D.3.3.4.4
futa = min(futa, 1.9*fya, 125 [ksi])
= min(58000[lb/in2], 1.9*36000[lb/in2], 125 [ksi])
= 58000[lb/in2] Sec. D.5.1.2
HasGroutPadFalse
Vsa = *0.6*n*Ase,V*futa
= 0.65*0.6*1*0.547[in2]*58000[lb/in2]
= 12.38[kip] Eq. D‐29
ca2Left = ca2Left
= 13.78[in] Sec. D.6.2.1
ca2Right<1.5*ca125.59[in]<1.5*13.78[in]False
ca2Right = 1.5*ca1
= 1.5*13.78[in]
= 20.67[in] Sec. D.5.2.1
ha<1.5*ca139.37[in]<1.5*13.78[in]False
ha = 1.5*ca1
= 1.5*13.78[in]
= 20.67[in] Sec. D.5.2.1
IsCloseToThreeEdgesFalse
ca1 = ca1
= 13.78[in] Sec. D.6.2.4
LVc = ca2Left + ca2Right
= 13.78[in] + 20.67[in]
= 34.45[in] Sec. RD.6.2.1
AVc = LVc*min(ha, 1.5*ca1)
= 34.45[in]*min(39.37[in], 1.5*13.78[in])
= 712.03[in2] Sec. RD.6.2.1
2
AVco = 4.5*ca1
2
= 4.5*13.78[in]
= 854.44[in2] Eq. D‐32
ca2<1.5*ca113.78[in]<1.5*13.78[in]True
39
Simple Tech One Co., Ltd.
ed,V = 0.7 + 0.3*(ca2/(1.5*ca1))
= 0.7 + 0.3*(13.78[in]/(1.5*13.78[in]))
= 0.9 Eq. D‐28
CrackedConcreteFalse
c,V = 1.4 Sec. D.6.2.7
ha<1.5*ca139.37[in]<1.5*13.78[in]False
h,V = 1 Sec. D.6.2.8
le = min(hef, 8*da)
= min(23.62[in], 8*0.945[in])
= 7.56[in] Sec. D.6.2.2
0.2 1/2 1/2 1.5 1/2 1.5
Vb = min((7*(le/da) *(da/(1 [in])) )*a*(fc/(1 [psi])) *(ca1/(1 [in])) [lb], 9*a*(fc/(1 [psi])) *(ca1/(1 [in])) [lb])
0.2 1/2 1/2
= min((7*(7.56[in]/0.945[in]) *(0.945[in]/(1 [in])) )*1*(3000[lb/in2]/(1 [psi])) *(13.78[in]/
1.5 1/2 1.5
(1 [in])) [lb], 9*1*(3000[lb/in2]/(1 [psi])) *(13.78[in]/(1 [in])) [lb])
= 25.21[kip] Eq. D‐33, D‐34
Vcb = (AVc/AVco)*ed,V*c,V*h,V*Vb
= (712.03[in2]/854.44[in2])*0.9*1.4*1*25.21[kip]
= 26.48[kip] Eq. D‐30
Vcb = *Vcb
= 0.7*26.48[kip]
= 18.53[kip] Table D.4.1.1,
Sec. D.4.3
kcp = 2 Sec. D.6.3.1
ca1Left<1.5*hef13.78[in]<1.5*23.62[in]True
ca1Left = ca1Left
= 13.78[in] Sec. D.5.2.1
ca1Right<1.5*hef25.59[in]<1.5*23.62[in]True
ca1Right = ca1Right
= 25.59[in] Sec. D.5.2.1
ca2Top<1.5*hef13.78[in]<1.5*23.62[in]True
ca2Top = ca2Top
= 13.78[in] Sec. D.5.2.1
ca2Bot<1.5*hef25.59[in]<1.5*23.62[in]True
ca2Bot = ca2Bot
= 25.59[in] Sec. D.5.2.1
40
Simple Tech One Co., Ltd.
IsCloseToThreeEdgesTrue
hef = camax/1.5
= 25.59[in]/1.5
= 17.06[in] Sec. D.5.2.3
ca1Left<1.5*hef13.78[in]<1.5*17.06[in]True
ca1Left = ca1Left
= 13.78[in] Sec. D.5.2.1
ca1Right<1.5*hef25.59[in]<1.5*17.06[in]False
ca1Right = 1.5*hef
= 1.5*17.06[in]
= 25.59[in] Sec. D.5.2.1
ca2Top<1.5*hef13.78[in]<1.5*17.06[in]True
ca2Top = ca2Top
= 13.78[in] Sec. D.5.2.1
ca2Bot<1.5*hef25.59[in]<1.5*17.06[in]False
ca2Bot = 1.5*hef
= 1.5*17.06[in]
= 25.59[in] Sec. D.5.2.1
ANc = (ca1Left + ca1Right)*(ca2Top + ca2Bot)
= (13.78[in] + 25.59[in])*(13.78[in] + 25.59[in])
= 1550[in2] Sec. RD.5.2.1
2
ANco = 9*hef
2
= 9*17.06[in]
= 2619.51[in2] Eq. D‐5
ca,min<1.5*hef13.78[in]<1.5*17.06[in]True
ed,N = 0.7 + 0.3*ca,min/(1.5*hef)
= 0.7 + 0.3*13.78[in]/(1.5*17.06[in])
= 0.862 Eq. D‐10
CrackedConcreteFalse
c,N = 1.25 Sec. D.5.2.6
IsCastInPlaceAnchorTrue
cp,N = 1 Sec. D.5.2.7
IsCastInPlaceAnchorTrue
kc = 24 Sec. D.5.2.2
(IsCastInPlaceAnchor) and (IsHeadedBolt) and (hef>=11 [in]) and (hef<=25 [in])(True) and (False) and (17.06[in]> = 11 [in]) and (17.06[in]<
= 25 [in])False
41
Simple Tech One Co., Ltd.
1/2 1.5
Nb = kc*a*(fc/(1 [psi])) *(hef/(1 [in])) [lb]
1/2 1.5
= 24*1*(3000[lb/in2]/(1 [psi])) *(17.06[in]/(1 [in])) [lb]
= 92.63[kip] Eq. D‐6
Ncb = (ANc/ANco)*ed,N*c,N*cp,N*Nb
= (1550[in2]/2619.51[in2])*0.862*1.25*1*92.63[kip]
= 59.03[kip] Eq. D‐3
Vcp = kcp*Ncb
= 2*59.03[kip]
= 118.05[kip] Eq. D‐40
Vcp = *Vcp
= 0.7*118.05[kip]
= 82.64[kip] Table D.4.1.1,
Sec. D.4.3
Ratio 0.00
Major axis
Maximum compression (D3)
--------------------------------------------------------------
Maximum bearing pressure 59.47 [psi]
Minimum bearing pressure 59.47 [psi]
Maximum anchor tension 1.16 [Kip]
Minimum anchor tension 0.00 [Kip]
Neutral axis angle 0.00
Bearing length 3.44 [in]
--------------------------------------------------------------
Anchors tensions
Anchor Transverse Longitudinal Shear Tension
[in] [in] [Kip] [Kip]
-----------------------------------------------------------------------------
1 -5.91 -5.91 0.07 0.00
2 -5.91 5.91 0.07 1.16
3 5.91 5.91 0.07 1.16
4 5.91 -5.91 0.07 0.00
-----------------------------------------------------------------------------
42
Simple Tech One Co., Ltd.
Maximum tension (WX)
--------------------------------------------------------------
Maximum bearing pressure 58.08 [psi]
Minimum bearing pressure 58.08 [psi]
Maximum anchor tension 1.37 [Kip]
Minimum anchor tension 0.00 [Kip]
Neutral axis angle 0.00
Bearing length 2.99 [in]
--------------------------------------------------------------
Anchors tensions
Anchor Transverse Longitudinal Shear Tension
[in] [in] [Kip] [Kip]
-----------------------------------------------------------------------------
1 -5.91 -5.91 0.07 0.00
2 -5.91 5.91 0.07 1.37
3 5.91 5.91 0.07 1.37
4 5.91 -5.91 0.07 0.00
-----------------------------------------------------------------------------
Minor axis
Maximum compression (D1)
----------------------------------------------------------------
Maximum bearing pressure 4.23 [psi]
Minimum bearing pressure 4.23 [psi]
Maximum anchor tension 0.00 [Kip]
Minimum anchor tension 0.00 [Kip]
Neutral axis angle 0.00
Bearing length 1.2E31 [in]
----------------------------------------------------------------
43
Simple Tech One Co., Ltd.
Anchors tensions
Anchor Transverse Longitudinal Shear Tension
[in] [in] [Kip] [Kip]
-----------------------------------------------------------------------------
1 -5.91 -5.91 0.00 0.00
2 -5.91 5.91 0.00 0.00
3 5.91 5.91 0.00 0.00
4 5.91 -5.91 0.00 0.00
-----------------------------------------------------------------------------
----------------------------------------------------------------
Maximum bearing pressure 0.60 [psi]
Minimum bearing pressure 0.60 [psi]
Maximum anchor tension 0.00 [Kip]
Minimum anchor tension 0.00 [Kip]
Neutral axis angle 0.00
Bearing length 1.2E31 [in]
----------------------------------------------------------------
Anchors tensions
Anchor Transverse Longitudinal Shear Tension
[in] [in] [Kip] [Kip]
-----------------------------------------------------------------------------
1 -5.91 -5.91 0.00 0.00
2 -5.91 5.91 0.00 0.00
3 5.91 5.91 0.00 0.00
4 5.91 -5.91 0.00 0.00
-----------------------------------------------------------------------------
Major axis
Results for tensile breakout (WX)
44
Simple Tech One Co., Ltd.
Results for shear breakout (WX)
NOTATION
A1: Base plate area
A2: Maximum area of portion of the concrete supporting surface that is geometrically similar to and concentric with the load area
Aw: Effective area of the weld
A2/A1: Ratio between the concrete support area and the base plate area
B: Base plate design width
bc : Width of column section
beff: Effective width of the compression block
Beff: Controlling effective width
c: Distance to weld group
D: Outside section diameter
dc : Column depth
D: Number of sixteenths of an inch in the weld size
fa: Axial stress on welds
fb: Bending stress on welds
f'c: Specified compressive strength of concrete
f: Combined stress on welds
FEXX: Electrode classification number
fp: Uniformly bearing stress under base plate
fp, max: Maximum uniformly bearing stress under base plate
fv: Vertical shear force on weld
Fw: Nominal strength of the weld metal per unit area
Fy: Specified minimum yield stress
I: Inertia of weld group
L: Distance from the anchor rod to the column
l: Critical base plate cantilever dimension
L: Length of weld
Lshear: Length of weld receiving shear
: Auxiliary variable to calculate the critical base plate cantilever dimension
LoadAngleFactor: Load angle factor
M: Bending required
m: Base plate bearing interface cantilever direction parallel to moment direction
Mpl: Plate bending moment per unit width
MpM: Plate bending moment per unit width at bearing interface for the cantilever m
MpN: Plate bending moment per unit width at bearing interface for the cantilever n
MpT: Plate bending moment per unit width at tension unstiffened strip interface
Mstrip: Maximum bending moment at the strip
Maximum weld load: Maximum weld load
N: Base plate design length
n: Base plate bearing interface cantilever direction perpendicular to moment direction
n': Yield line theory cantilever distance from column web or column flange
Ncs: Length of the concrete supporting surface or pier parallel to moment design direction
P: Required axial force
Pp: Nominal bearing stress
: Design factors
Mn: Design or allowable strength per unit length
Rw: Fillet weld capacity per unit length
T: Anchor rod tensile strength required
tp: Plate thickness
: Load angle
V: Shear load
wmin: Minimum weld size required
X: Auxiliary variable to calculate the critical base plate cantilever dimension
ANc: Projected concrete failure area of a single anchor or group of anchors, for calculation of strength in tension
45
Simple Tech One Co., Ltd.
ANco: Projected concrete failure area of a single anchor, for calculation of strength in tension if not limited by edge distance or spacing
Ase: Effective cross-sectional area of anchor
Ase,N: Effective cross-sectional area of anchor in tension
Ase,V: Effective cross-sectional area of anchor in shear
AVc: Projected concrete failure area of a single anchor or group of anchors , for calculation of strength in shear
AVco: Projected concrete failure area of a single anchor, for calculation of strength in shear, if not limited by corner influences, spacing, or member
thickness
ca1: Distance from the anchor center to the concrete edge
ca1Left: Distance from the anchor center to the left edge of the concrete base
ca1Right: Distance from the anchor center to the right edge of the concrete base
ca2: Distance from the anchor center to the concrete edge in perpendicular direction
ca2Bot: Distance from the anchor center to the bottom edge of the concrete base
ca2Left: Distance from the anchor center to the left edge of the concrete base
ca2Right: Distance from the anchor center to the right edge of the concrete base
ca2Top: Distance from the anchor center to the top edge of the concrete base
camax: Maximum distance from center of an anchor shaft to the edge of concrete
ca,min: Minimum distance from center of an anchor shaft to the edge of concrete
Cover: Concrete cover
CrackedConcrete: Cracked concrete at service loads
da: Outside diameter of anchor or shaft diameter of headed stud, headed bolt, or hooked bolt
eh: Distance from the inner surface of the shaft of a J- or L-bolt to the outer tip of the J- or L-bolt
e'N: Distance between resultant tension load on a group of anchors loaded in tension and the centroid of the group of anchors loaded in tension
e'V: Distance between resultant shear load on a group of anchors loaded in shear in the same direction, and the centroid of the group of anchors
loaded in shear in the same direction
fc : Specified compressive strength of concrete
futa: Specified tensile strength of anchor steel
fya: Specified yield strength of anchor steel
ha: Thickness of member in which an anchor is located, measured parallel to anchor axis
hef: Effective embedment depth of anchor
HasGroutPad: Has grout pad
HighSeismicDesignCategory:High seismic design category (i.e. C, D, E or F)
IsCastInPlaceAnchor: Is cast in place anchor
IsCloseToThreeEdges: Anchor is close to three or more edges
IsConcreteCastAgainstEarth:Is concrete cast against and permanently exposed to earth
IsHeadedBolt: Is anchor headed stud
kc: Coefficient for concrete pry out basic strength
kcp: Coefficient for pry out strength
le: Load-bearing length of the anchor for shear
LVc: Projected concrete failure length of a single anchor or group of anchors , for calculation of strength in shear
a: Lightweight concrete modification factor
n: Number of anchors in the group
Nb: Basic concrete breakout strength in tension of a single anchor in cracked concrete
Ncb: Nominal concrete breakout strength in tension of a single anchor
Ncbg: Nominal concrete breakout strength in tension of a group of anchors
Np: Pullout strength in tension of a single anchor in cracked concrete
Npn: Nominal pullout strength of a single anchor in tension
nt: Number of threads per inch
Nua: Factored tensile force applied to anchor or group of anchors
: Strength reduction factor
Ncb: Concrete breakout strength in tension of a single anchor
Ncbg: Concrete breakout strength in tension of a group of anchors
Nn: Tension strength
Npn: Pullout strength in tension of a single anchor
Nsa: Strength of a single anchor or group of anchors in tension
Vcb: Concrete breakout strength in shear of a single anchor
Vcbg: Concrete breakout strength in shear of a group of anchors
Vcp: Concrete pryout strength of a single anchor
Vcpg: Concrete pryout strength of a group of anchors
Vn: Shear strength
Vsa: Strength in shear of a single anchor or group of anchors as governed by the steel strength
c,N: Factor used to modify tensile strength of anchors based on presence or absence of cracks in concrete
c,P: Factor used to modify pullout strength of anchors based on presence or absence of cracks in concrete
cp,N: Factor used to modify tensile strength of postinstalled anchors intended for use in uncracked concrete without supplementary reinforcement
c,V: Factor used to modify shear strength of anchors based on presence or absence of cracks in concrete and presence or absence of
supplementary reinforcement
ec,N: Factor used to modify tensile strength of anchors based on eccentricity of applied loads
ec,Nx: Factor used to modify tensile strength of anchors based on eccentricity in x axis of applied loads
ec,Ny: Factor used to modify tensile strength of anchors based on eccentricity in y axis of applied loads
ec,V: Factor used to modify shear strength of anchors based on eccentricity of applied loads
ed,N: Factor used to modify tensile strength of anchors based on proximity to edges of concrete member
46
Simple Tech One Co., Ltd.
ed,V: Factor used to modify shear strength of anchors based on proximity to edges of concrete member
h,V: Factor used to modify shear strength of anchors located in concrete members with ha < 1.5ca1
smin: Center-to-center anchor minimum spacing
TensionShearInteraction: Result from tension-shear interaction
Vb: Basic concrete breakout strength in shear of a single anchor in cracked concrete
Vcb: Concrete nominal breakout strength in shear of a single anchor
Vcbg: Concrete nominal breakout strength in shear of a group of anchors
Vcp: Nominal pryout strength of a anchor in shear
Vcpg: Nominal pryout strength of a group of anchor in shear
Vua: Factored shear force applied to anchor or group of anchors
47
Project Simple Job
Tech One Co., Ltd.
Ref.
FOOTING ANALYSIS
Length of foundation; Lx = 3.3 ft
Width of foundation; Ly = 3.3 ft
Foundation area; A = Lx Ly = 10.89 ft2
Depth of foundation; h = 52 in
Depth of soil over foundation; hsoil = 0 in
Density of concrete; conc = 150.0 lb/ft3
1 x
48
Project Simple Job
Tech One Co., Ltd.
Ref.
Moments on foundation
Moment in x-axis, about x is 0; Mdx = D A Fswt Lx / 2 + D (FDz1 x1) + W (MWx1+FWx1 h) = 14.4
kip_ft
Moment in y-axis, about y is 0; Mdy = D A Fswt Ly / 2 + D (FDz1 y1) = 12.0 kip_ft
Uplift verification
Vertical force; Fdz = 7.289 kips
PASS - Foundation is not subject to uplift
Stability against overturning in x direction, moment about x is Lx
Overturning moment; MOTxL = W (MWx1+FWx1 h) = 2.35 kip_ft
Resisting moment; MRxL = -1 (D A Fswt Lx / 2) + D (FDz1 (x1 - Lx)) = -12.03 kip_ft
Factor of safety; abs(MRxL / MOTxL) = 5.108
PASS - Overturning moment safety factor exceeds the minimum of 1.00
Stability against sliding
Resistance due to base friction; FRFriction = max(Fdz, 0 kN) tan(bb) = 4.208 kips
49
Project Simple Job
Tech One Co., Ltd.
Ref.
Moments on foundation
Ultimate moment in x-axis, about x is 0; Mux = D A Fswt Lx / 2 + D (FDz1 x1) + W (MWx1+FWx1 h) = 14.7
kip_ft
Ultimate moment in y-axis, about y is 0; Muy = D A Fswt Ly / 2 + D (FDz1 y1) = 10.8 kip_ft
50
Project Simple Job
Tech One Co., Ltd.
Ref.
-1.7
-1.9
00.0
0
0.0 0
0
-0.1
0.1
51
Project Simple Job
Tech One Co., Ltd.
Ref.
52