Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
ANSI/AWWA-C110/A21.10 Standard
and
ANSI B16.1 Class 125 Standard
SPECIFICATIONS
Flanged fittings shown on the pages immediately following are manufactured to either ANSI/AWWA-C110/
A21.10 or to ANSI B16.1 standard as indicated on each page heading. Elbows or bends (straight sizes),
tees, crosses, concentric reducers, base elbows (except reducing size) and bottom base tees are manu-
factured to ANSI/AWWA-C110/A21.10 standard. These fittings have identical face to face and center to
face dimensions and the same flange drilling as ANSI B16.1 fittings, but differ slightly in wall thickness.
Ductile iron C110/A21.10 flanged fittings are rated for 150 or 250 psi water working pressure as listed in
the tables.
Long radius and reducing elbows, reducing on-the-run tees, side outlet fittings, eccentric reducers and
laterals are ANSI B16.1 Class 125 fittings. Ductile iron Class 125 fittings are furnished manufacturer's
standard for 250 psi water working pressure. Flanged offsets and true wyes are furnished manufacturer's
standard.
We do not spot face back of flanges. Where spot facing is required, the back of the flange is machined
over its entire surface.
When ordering any flanged fittings equipped with bosses and/or tapped holes, refer to and use the letter
key on page ??, which designates location by letter.
Standard 125 pound template for drilling shown below is used for all flanged fittings whether ANSI/AWWA-
C110/A21.10 or ANSI B16.1.
Note: The flanges shown above are adequate for 250 psi water working pressure. They should not be con-
fused with 250 pound extra heavy flanges covered by ANSI B16.1 which are rated for 250 psi steam work-
ing pressure.
DIMENSIONS
REDUCING CROSSES
REDUCING LATERALS
Reducing on Reducing
Branch True Y
Tapping through the wall of the fitting is limited to sizes indicated in the table below. Larger size tapped
openings will require casting the fitting with an intergral boss—the location of which may also be identified
by a letter, as explained above. A boss is always required at “V” and “Y” on straight and reducing sizes of
90° elbows, and on all sides of reducers.
BENDS
Furnished Faced and Drilled to 125 Pound
Template Unless Otherwise Ordered
Straight Reducing
90° Long Radius Elbow 90° Long Radius Elbow
DIMENSIONS AND WEIGHTS
Nominal Dimensions Inches Approximate Nominal Dimensions Inches Approximate
Pipe Size Weight Pipe Size Weight
Inches T T1 B Pounds Inches T T1 B Pounds
3x3 .37 . . . 7.75 28 14 x 10 .87 .75 21.50 375
4x4 .50 . . . 9.00 50 14 x 12 .87 .81 21.50 425
5x4 .50 .50 10.25 60 14 x 14 .87 ... 21.50 475
5x5 .50 . . . 10.25 62 16 x 8 1.0 .62 24.00 420
6x4 .56 .50 11.50 70 16 x 10 1.0 .75 24.00 480
6x5 .56 .50 11.50 75 16 x 12 1.0 .81 24.00 530
6x6 .56 . . . 11.50 80 16 x 14 1.0 .87 24.00 590
8x4 .62 .50 14.00 100 16 x 16 1.0 ... 24.00 630
8x5 .62 .50 14.00 110 18 x 12 1.06 .81 26.50 635
8x6 .62 .56 14.00 120 18 x14 1.06 .87 16.50 480
8x8 .62 . . . 14.00 140 18 x16 1.06 1 26.50 775
10 x 4 .75 .50 16.50 145 18 x 18 1.06 ... 26.50 840
10 x 6 .75 .56 16.50 170 20 x 14 1.12 .87 29.00 820
10 x 8 .75 .62 16.50 195 20 x 16 1.12 1.0 29.00 915
l0 x l0 .75 . . . 16.50 230 20 x 20 1.12 ... 29.00 1080
12 x 6 .81 .56 19.00 225 24 x 14 1.25 1.25 34.00 1280
12 x 8 .81 .62 19.00 260 24 x 16 1.25 1.25 34.00 1300
12 x 10 .81 .75 19.00 300 24 x 18 1.25 1.25 34.00 1365
12 x 12 .81 . . . 19.00 325 24 x 20 1.25 1.25 34.00 1430
14 x 8 .87 .62 21.50 330 24 x 24 1.25 1.25 34.00 1640
For Pressure Ratings and For Drilling Template See Page 52
Tee Cross
DIMENSIONS AND WEIGHTS
Nominal Diameter Inches Pressure Rating psi Dimensions Inches Approximate Weight Pounds
Run Branch Ductile T T1 H J Tee Cross
3 2 250 .48 .48 5.5 5.5 35 ...
3 3 250 .48 48 5.5 5.5 40 50
4 2 250 .52 .48 6.5 6.5 50 ...
4 3 250 .52 .48 6.5 6.5 60 70
4 4 250 .52 .52 6.5 6.5 60 80
5* 5* 250* .50 .50 7.5 7.5 81 105
6 2 250 .55 .48 8.0 8.0 85 ...
6 3 250 .55 .48 8.0 8.0 85 95
6 4 250 .55 .52 8.0 8.0 90 110
6 6 250 .55 .55 8.0 8.0 95 120
8 3 250 .60 .52 9.0 9.0 130 140
8 4 250 .60 .52 9.0 9.0 140 155
8 6 250 .60 .55 9.0 9.0 145 165
8 8 250 .60 .60 9.0 9.0 155 195
10 4 250 .68 .52 11.0 11.0 205 220
10 6 250 .68 .55 11.0 11.0 215 240
10 8 250 .68 .60 11.0 11.0 225 265
10 10 250 .80 .80 11.0 11.0 270 330
12 4 250 .75 .52 12.0 12.0 290 310
12 6 250 .75 .55 12.0 12.0 295 320
12 8 250 .75 .60 12.0 12.0 310 345
12 10 250 .87 .80 12.0 12.0 360 415
12 12 250 .87 .87 12.0 12.0 385 460
14 4 250 .66 .55 14.0 14.0 410 ...
14 6 250 .66 .55 14.0 14.0 420 450
14 8 250 .66 .60 14.0 14.0 435 475
14 10 250 .66 .68 14.0 14.0 450 460
14 12 250 .82 .75 14.0 14.0 470 555
14 14 250 .82 .82 14.0 14.0 500 595
16 4 250 .70 .55 15.0 15.0 525 ...
16 6 250 .70 .55 15.0 15.0 540 565
16 8 250 .70 .60 15.0 15.0 555 590
16 10 250 .70 .68 15.0 15.0 565 620
16 12 250 .70 .75 15.0 15.0 590 665
16 14 250 .89 .82 15.0 15.0 610 700
16 16 250 .89 .89 15.0 15.0 635 755
18 6 250 .75 .55 13.0 15.5 480 505
18 8 250 .75 .60 13.0 15.5 570 535
18 10 250 .75 .68 13.0 15.5 580 560
18 12 250 .75 .75 13.0 15.5 605 670
18 14 250 .75 .66 16.5 16.5 740 720
18 16 250 .75 .70 16.5 16.5 760 765
18 18 250 .75 .75 16.5 16.5 785 915
20 6 250 .80 .55 14.0 17.0 710 635
20 8 250 .80 .60 14.0 17.0 720 665
20 10 250 .80 .68 14.0 17.0 735 685
20 12 250 .80 .75 14.0 17.0 755 820
20 14 250 .80 .66 14.0 17.0 770 745
20 16 250 .80 .70 18.0 18.0 950 1065
20 18 250 .80 .75 18.0 18.0 820 945
20 20 250 .80 .80 18.0 18.0 1005 1175
* Five inch size is ANSI B16.1 fitting.
Flange accessories must be ordered separately.
DUCTILE IRON FLANGED FITTINGS
ANSI/AWWA-C110/A21.10 Standard
TEES AND CROSSES
Unless Otherwise Ordered Furnished Faced
and Drilled to 125 Pound Template
Tee Cross
Dimensions—Inches
Nominal Pipe Size Inches Approximate Weight Pounds
T T1 T2 A H
16 x 14 x 14 1.0 .87 .87 15.00 15.00 650
16 x 14 x 16 1.0 .87 1.0 15.00 15.00 680
18 x 12 x 12 1.06 .81 .81 13.00 15.50 610
18 x 12 x 14 1.06 .81 .87 16.50 16.50 750
18 x 12 x 18 1.06 .81 1.06 16.50 16.50 810
18 x 14 x 12 1.06 .87 .81 13.00 15.50 615
18 x 14 x 14 1.06 .87 .87 16.50 16.50 755
18 x 14 x 18 1.06 .87 1.06 16.50 16.50 815
18 x 16 x 18 1.06 1.0 1.06 16.50 16.50 825
20 x 16 x 14 1.12 1.0 .87 14.00 17.00 780
20 x 16 x 16 1.12 1.0 1.0 18.00 18.00 975
20 x 16 x 20 1.12 1.0 1.12 18.00 18.00 1040
20 x 18 x 20 1.12 1.06 1.12 18.00 18.00 1030
24 x 16 x 16 1.25 1.0 1.0 15.00 19.00 1085
24 x 16 x 18 1.25 1.0 1.06 22.00 22.00 1495
24 x 16 x 24 1.25 1.0 1.25 22.00 22.00 1635
24 x 18 x 16 1.25 1.06 1.0 15.00 19.00 1070
24 x 18 x 18 1.25 1.06 1.06 22.00 22.00 1485
24 x 18 x 24 1.25 1.06 1.25 22.00 22.00 1625
24 x 20 x 24 1.25 1.12 1.25 22.00 22.00 1630
30 x 16 x 16 1.03 .68 1.06 18.00 23.00 1345
30 x 16 x 18 1.03 .68 .75 18.00 23.00 1350
30 x 16 x 20 1.03 .68 .81 18.00 23.00 1375
30 x 16 x 24 1.03 .68 .87 25.00 25.00 1815
30 x 16 x 30 1.03 .68 1.03 25.00 25.00 1960
30 x 18 x 16 1.03 .75 1.06 18.00 23.00 1335
30 x 18 x 18 1.03 .75 .75 18.00 23.00 1340
30 x 18 x 20 1.03 .75 .81 18.00 23.00 1365
30 x 18 x 24 1.03 .75 .87 25.00 25.00 1805
30 x 18 x 30 1.03 .75 1.03 25.00 25.00 1955
30 x 20 x 16 1.03 .81 1.06 18.00 23.00 1340
30 x 20 x 18 1.03 .81 .75 18.00 23.00 1345
30 x 20 x 20 1.03 .81 .81 18.00 23.00 1370
30 x 20 x 24 1.03 .81 .87 25.00 25.00 1815
30 x 20 x 30 1.03 .81 1.03 25.00 25.00 1960
30 x 24 x 16 1.03 .87 1.06 18.00 23.00 1340
30 x 24 x 18 1.03 .87 .75 18.00 23.00 1345
30 x 24 x 20 1.03 .87 .81 18.00 23.00 1370
30 x 24 x 24 1.03 .87 .87 25.00 25.00 1820
30 x 24 x 30 1.03 .87 1.03 25.00 25.00 1965
Tees with branch and run openings smaller than those listed are also available.
Tees reducing on both runs are also available.
DUCTILE IRON FLANGED FITTINGS
ANSI/AWWA-C110/A21.10 Standard
CONCENTRIC REDUCERS
Furnished Faced and Drilled to
125 Pound Template.
For ANSI B16.1 Eccentric Flanged
Reducer, see page 67.
Eccentric Reducer
DIMENSIONS AND WEIGHTS
Dimensions Inches
Nominal Pipe Size Inches Approximate Weight Pounds
T T1 G
4x3 .50 .37 7.00 30
5x4 .50 .37 8.00 40
6x3 .56 .37 9.00 40
6x4 .56 .50 9.00 45
6x5 .62 .50 9.00 50
8x4 .62 .50 11.00 65
8x5 .62 .56 11.00 71
8x6 .62 .56 11.00 75
10 x 4 .75 .50 12.00 95
10 x 6 .75 .56 12.00 100
10 x 8 .75 .62 12.00 110
12 x 6 .81 .56 14.00 130
12 x 8 .81 .62 14.00 145
12 x 10 .81 .75 14.00 170
14 x 6 .87 .56 16.00 165
14 x 8 .87 .62 16.00 185
14 x 10 .87 .75 16.00 205
14 x 12 .87 .81 16.00 294
16 x 6 1.0 .56 18.00 210
16 x 8 1.0 .62 18.00 230
16 x 10 1.0 .75 18.00 255
16 x 12 1.0 .81 18.00 285
16 x 14 1.0 .87 18.00 315
18 x 8 1.06 .62 19.00 265
18 x 10 1.06 .75 19.00 290
18 x 12 1.06 .81 19.00 320
18 x 14 1.06 .87 19.00 350
18 x 16 1.06 1.0 19.00 385
20 x 10 1.12 .75 20.00 340
20 x 12 1.12 .81 20.00 375
20 x 14 1.12 .87 20.00 405
20 x 16 1.12 1.0 20.00 445
20 x 18 1.12 1.06 20.00 470
24 x 12 1.25 .81 24.00 535
24 x 14 1.25 .87 24.00 565
24 x 16 1.25 1.0 24.00 610
24 x 18 1.25 1.06 24.00 645
24 x 20 1.25 1.12 24.00 695
Flange accessories must be ordered separately.
Base Elbows
Nominal Diameter Pressure Rating psi Dimensions Inches Approximate Weight
Inches Ductile A R† S T U Pounds
3 250 5.5 4.88 5.00 .56 .50 35
4 250 6.5 5.50 6.00 .62 .50 55
6 250 8.0 7.00 7.00 .69 .62 85
8 250 9.0 8.38 9.00 .94 .88 145
10 250 11.0 9.75 9.00 .94 .88 210
12 250 12.0 11.25 11.00 1.00 1.00 300
14 250 14.0 12.50 11.00 1.00 1.00 400
16 250 15.0 13.75 11.00 1.00 1.00 505
18 250 16.5 15.00 13.50 1.12 1.12 645
20 250 18.0 16.00 13.50 1.12 1.12 805
24 250 22.0 18.50 13.50 1.12 1.12 1215
30 250 25.0 23.00 16.00 1.19 1.15 1945
* Five inch size is ANSI B16.1 fitting.
LATERALS
For True Y Fittings, see page 61 For Pressure Ratings see page 55.
Straight Lateral DIMENSIONS AND WEIGHTS Reducing Lateral
Nominal Dimensions Inches Approximate Weight
Pipe Size T T1 E F L Pounds
3 x 3x 3 .37 ... 10.00 3.00 ... 45
4x4x3 .50 .37 12.00 3.00 12.00 65
4x4x4 .50 ... 12.00 3.00 ... 75
6x6x3 .56 .37 14.50 3.50 14.50 105
6x6x4 .56 .50 14.50 3.50 14.50 105
6x6x6 .56 ... 14.50 3.50 ... 115
8x8x4 .62 .50 17.50 4.50 17.50 165
8x8x6 .62 .56 17.50 4.50 17.50 175
8x8x8 .62 ... 17.50 4.50 ... 200
10 x 10 x 4 .75 .50 20.50 5.00 20.50 240
10 x 10 x 6 .75 .56 20.50 5.00 20.50 250
10 x 10 x 8 .75 .62 20.50 5.00 20.50 275
10 x 10 x 10 .75 ... 20.50 5.00 ... 300
12 x 12 x 4 .81 .50 24.50 5.50 24.50 355
12 x 12 x 6 .81 .56 24.50 5.50 24.50 370
12x 12 x 8 .81 .62 24.50 5.50 24.50 395
12 x 12 x 10 .81 .75 24.50 5.50 24.50 420
12 x 12 x 12 .81 ... 24.50 5.50 ... 460
14 x 14 x 6 .87 .56 27.00 6.00 27.00 500
14 x 14 x 8 .87 .62 27.00 6.00 27.00 525
14 x 14 x 10 .87 .75 27.00 6.00 27.00 555
14 x 14 x 12 .87 1.18 27.00 6.00 27.00 600
14 x 14 x 14 .87 ... 27.00 6.00 ... 640
16 x 16 x 6 1.0 .56 30.00 6.50 30.00 655
16 x 16 x 8 1.0 .62 30.00 6.50 30.00 680
16 x 16 x 10 1.0 .75 30.00 6.50 30.00 715
16 x 16 x 12 1.0 .81 30.00 6.50 30.00 755
16 x 16 x 14 1.0 .87 30.00 6.50 30.00 800
16 x 16 x 16 1.0 ... 30.00 6.50 ... 850
18 x 18 x 6* 1.06 .56 25.00 1.00 27.50 860
18 x 18 x 8* 1.06 .62 25.00 1.00 27.50 820
18 x 18 x 10 1.06 .75 32.00 7.00 32.00 855
18 x 18 x 12 1.06 .81 32.00 7.00 32.00 895
18 x 18 x 14 1.06 .87 32.00 7.00 32.00 940
18 x 18 x 16 1.06 1.0 32.00 7.00 32.00 990
18 x 18 x 18 1.06 ... 32.00 7.00 ... 1035
20 x 20 x 8* 1.12 .62 27.00 1.00 29.50 800
20 x 20 x 10* 1.12 .75 27.00 1.00 29.50 1095
20 x 20 x 12 1.12 .81 35.00 8.00 35.00 1130
20 x 20 x 14 1.12 .87 35.00 8.00 35.00 1170
20 x 20 x 16 1.12 1.0 35.00 8.00 35.00 1220
20 x 20 x 18 1.12 1.06 35.00 8.00 35.00 l400
20 x 20 x 20 1.12 ... 35.00 8.00 ... 1345
24 x 24 x 8* 1.25 .62 31.50 .50 34.50 1180
24 x 24 x 10* 1.25 .75 31.50 .50 34.50 1200
24 x 24 x 12* 1.25 .81 31.50 .50 34.50 1250
24 x 24 x 14 1.25 .87 40 50 9.00 40 50 1810
24 x 24 x 16 1.25 1.0 40.50 9.00 40.50 1890
24 x 24 x 18 1.25 1.06 40.50 9.00 40.50 1950
24 x 24 x 20 1.25 1.12 40.50 9.00 40.50 2040
24 x 24 x 24 1.25 ... 40.50 9.00 ... 2020
30 x 30 x 8 1.37 .63 39.0 0.0 42.0 1790
30 x 30 x 10 1.37 .75 39.0 0.0 42.0 1830
30 x 30 x 12 1.37 .81 39.0 0.0 42.0 1875
30 x 30 x 14 1.37 .88 39.0 0.0 42.0 1910
30 x 30 x 16 1.37 1.00 49.0 10.0 49.0 2765
30 x 30 x 18 1.37 1.06 49.0 10.0 49.0 2820
30 x 30 x 20 1.37 1.13 49.0 10.0 49.0 2895
30 x 30 x 24 1.37 1.25 49.0 10.0 49.0 3045
30 x 30 x 30 1.37 1.37 49.0 10.0 49.0 3285
*Regularly furnished short pattern. Can be made to special order with long body dimensions.
Flange accessories must be ordered separately.
DUCTILE IRON FLANGED FlTTINGS
Section
Blind Flange 3” thru 10” Dished Blind Flange*
16-inch O.D. and Smaller 19-lnch O.D. and Larger
FLANGE FILLERS
Fillers—Full Size of Flange
Used for closing up between two flanges which do not meet. Maximum thickness
is six inches; minimum thickness is 3/8 inch.
Flange Adapter
The Flange Adapter is used to connect flanged pipe or fittings with Class 125 flanges to Class 250 flanges
of ANSI B16.1 standard. Common center lines are marked to eliminate difficulty in installaton.
We can furnish pipe or fittings with Class 250 flanges, on special order in limited configurations.
The Flange Adapter is rated for 250 psi water working pressure. Adapters are cast of ductile iron for sizes
3” - 30”.
Suction Strainer
Pipe Size O.D. of Area in Square Inches Overall Length Approximate Weight
Inches Strainer Inches of Pipe Port of Perforations “L” in Inches Pounds
4 7.00 12.50 20.00 11.75 40
6 9.00 28.00 37.50 12.25 75
8 13.00 50.00 75.00 15.00 115
10 15.25 78.50 84.00 20.63 175
12 17.25 113.00 126.00 22.13 260
Slots in all strainers are 1/2 inch wide.
*Note: Flanged ends are regularly furnished faced and drilled to 125 pound template—see page 55.