Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: -|- Date: 1/13/2011
E-Mail:
Specifier's comments:
1. Input data
Anchor type and diameter: Kwik Bolt TZ - CS, 1/2 (3 1/4)
Effective embedment depth: h ef = 3.250 in.
Material: Carbon Steel
Evaluation Service Report:: ESR 1917
Issued I Valid: 9/1/2009 | -
Proof: design method ACI 318 / AC 193
Stand-off installation: e b = 0.000 in. (no stand-off); t = 2.000 in.
Anchor plate: lx x l y x t = 35.000 x 16.000 x 2.000 in. (Recommended plate thickness: not calculated)
Profile Round HSS, Steel pipe (AISC); (L x W x T) = 8.630 in. x 8.630 in. x 0.322 in.
Base material: uncracked concrete , 4000, fc ' = 4000 psi; h = 420.000 in.
Reinforcement: tension: condition B, shear: condition B; no supplemental splitting reinforcement present
edge reinforcement: none or < No. 4 bar
Geometry [in.]
35.000
x
t=2.000
x h = 420.000
h nom=4.000
16.000
9.292
lx = 35.000
9.2919.2929.291
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us PROFIS Anchor 2.1.1
Company: Page: 2
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: -|- Date: 1/13/2011
E-Mail:
Anchor Tension force Shear force Shear force x Shear force y Tension y
5 6 7 8
1 1559 125 125 0
x
2 985 125 125 0
Compression
3 411 125 125 0 1 2 3 4
4 0 125 125 0
5 3880 125 125 0
6 3307 125 125 0
7 2731 125 125 0
8 2158 125 125 0
3. Tension load
Proof Load Nua [lb] Capacity fN n [lb] Utilization bN [%] = Nua /fNn Status
Steel Strength* 3881 8029 48 OK
Pullout Strength* 3881 4534 86 OK
Concrete Breakout Strength** 15032 20619 73 OK
* anchor having the highest loading **anchor group (anchors in tension)
Steel Strength
Equations
Nsa = ESR value refer to ICC-ES ESR 1917
f Nsteel ≥ Nua ACI 318-08 Eq. (D-1)
Variables
n Ase,N [in.2]
1 0.10
Calculations
Nsa [lb]
10705
Results
Nsa [lb] fsteel f Nsa [lb] Nua [lb]
10705 0.750 8029 3881
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us PROFIS Anchor 2.1.1
Company: Page: 3
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: -|- Date: 1/13/2011
E-Mail:
Pullout Strength
Equations
√2500
'
f c
Npn,f'c = Np,2500 refer to ICC-ES ESR 1917
Variables
f'c [psi] Np,2500 [lb]
4000 5515
Calculations
√
f'c
2500
1.265
Results
Npn,f'c [lb] fconcrete f Npn,f'c [lb] Nua [lb]
6976 0.650 4534 3881
Equations
Ncbg =
ANc
( ) N
ANc0 yec,N yed,N yc,N ycp,N b
ACI 318-08 Eq. (D-5)
f Ncbg ≥ Nua ACI 318-08 Eq. (D-1)
ANc see ACI 318-08, Part D.5.2.1, Fig. RD.5.2.1(b)
ANc0 = 9 h2ef ACI 318-08 Eq. (D-6)
( )
1
yec,N = 2 e'N ≤ 1.0 ACI 318-08 Eq. (D-9)
1+
3 hef
ac
(
ca,min 1.5hef
ycp,N = MAX c , c
ac
≤ 1.0 ) ACI 318-08 Eq. (D-13)
1.5
Nb = kc l √fc hef
'
ACI 318-08 Eq. (D-7)
Variables
hef [in.] ec1,N [in.] ec2,N [in.] ca,min [in.] yc,N cac [in.] kc l
3.250 1.407 2.156 393.701 1.000 6.000 24 1
f'c [psi]
4000
Calculations
ANc [in.2] ANc0 [in.2] yec1,N yec2,N yed,N ycp,N Nb [lb]
630.11 95.06 0.776 0.693 1.000 1.000 8893
Results
Ncbg [lb] fconcrete f Ncbg [lb] Nua [lb]
31721 0.650 20619 15032
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us PROFIS Anchor 2.1.1
Company: Page: 4
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: -|- Date: 1/13/2011
E-Mail:
4. Shear load
Proof Load V ua [lb] Capacity fVn [lb] Utilization bV [%] = Vua /fVn Status
Steel Strength* 125 4163 3 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout Strength** 1000 93835 1 OK
Concrete edge failure in N/A N/A N/A N/A
direction**
* anchor having the highest loading **anchor group (relevant anchors)
Steel Strength
Equations
Vsa = ESR value refer to ICC-ES ESR 1917
f Vsteel ≥ Vua ACI 318-08 Eq. (D-1)
Variables
n Ase,V [in.2]
1 0.10
Calculations
Vsa [lb]
6405
Results
Vsa [lb] fsteel f Vsa [lb] Vua [lb]
6405 0.650 4163 125
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us PROFIS Anchor 2.1.1
Company: Page: 5
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: -|- Date: 1/13/2011
E-Mail:
Equations
Vcpg = kcp [(AA ) y
Nc
Nc0
ec,N yed,N yc,N ycp,N Nb ] ACI 318-08 Eq. (D-31)
f Vcpg ≥ Vua ACI 318-08 Eq. (D-1)
ANc see ACI 318-08, Part D.5.2.1, Fig. RD.5.2.1(b)
ANc0 = 9 h2ef ACI 318-08 Eq. (D-6)
( )
1
yec,N = 2 e'N ≤ 1.0 ACI 318-08 Eq. (D-9)
1+
3 hef
ycp,N = MAX c , c(
ca,min 1.5hef
ac ac
)
≤ 1.0 ACI 318-08 Eq. (D-13)
1.5
Nb = kc l √f'c hef ACI 318-08 Eq. (D-7)
Variables
kcp hef [in.] ec1,N [in.] ec2,N [in.] ca,min [in.] yc,N cac [in.] kc
2 3.250 0.000 0.000 - 1.000 - 24
l f'c [psi]
1 4000
Calculations
ANc [in.2] ANc0 [in.2] yec1,N yec2,N yed,N ycp,N Nb [lb]
716.44 95.06 1.000 1.000 1.000 1.000 8893
Results
Vcpg [lb] fconcrete f Vcpg [lb] Vua [lb]
134050 0.700 93835 1000
6. Warnings
• Condition A applies when supplementary reinforcement is used. The Φ factor is increased for non-steel Design Strengths except Pullout
Strength and Pryout strength. Condition B applies when supplementary reinforcement is not used and for Pullout Strength and Pryout
Strength. Refer to ACI 318, Part D.4.4(c).
• Refer to the manufacturer's product literature for cleaning and installation instructions.
• Checking the transfer of loads into the base material and the shear resistance are required in accordance with ACI318 or the relevant
standard!
• The anchor plate is assumed to be sufficiently stiff in order to be not deformed when subjected to the actions!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us PROFIS Anchor 2.1.1
Company: Page: 6
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: -|- Date: 1/13/2011
E-Mail:
7. Installation data
Anchor plate, steel: - Anchor type and diameter: Kwik Bolt TZ - CS, 1/2 (3 1/4)
Profile: Round HSS, Steel pipe (AISC), 8.630 in. x 8.630 in. x 0.322 in. Installation torque: 480.001 in.-lb
Hole diameter in the fixture: df = 0.563 in. Hole diameter in the base material: 0.500 in.
Plate thickness (input): 2.000 in. Hole depth in the base material: 4.000 in.
Recommended plate thickness: not calculated Minimum thickness of the base material: 8.000 in.
3.3540
8.0000
5 6 7 8
x
8.0000
3.3540
1 2 3 4
3.5630 3.5630
17.5000 17.5000
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan