Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Top of Form
Which parameter is associated with wireless authentication?
shared key
SSID
ad hoc
Channel
2
Top of Form
A network administrator is asked to connect four switches that are each configured with eight
VLANs. Routers that have two FastEthernet ports each that support trunking are available. What
is the minimum number of routers needed to interconnect traffic from all of the VLANs if
trunking is allowed?
1
8
16
3
Top of Form
A wireless access point can function as which type of shared medium, wired LAN device?
hub
switch
router
Gateway
4
Top of Form
Refer to the exhibit. Assuming the bridge priority values are set to default on all switches, which
switch will be elected as the root bridge of the spanning tree topology?
Cat-A
Cat-B
Cat-C
Cat-D
5
Top of Form
Refer to the exhibit. The switch VTY lines have been properly configured, but PC1 is unable to
remotely manage the switch. How can this problem be resolved?
Configure the Fa0/1 interface of the switch in trunk mode.
6
Top of Form
Refer to the exhibit. Both switches are configured as displayed and the native VLAN is the
default. Which statement is true about the frames traveling between host A and host B?
They will travel untagged.
7
Top of Form
Which benefit is gained by designing a network with a small network diameter?
lower latency
improved security
increased redundancy
higher interface bandwidth
8
Top of Form
Refer to the exhibit. Both switches are configured with default bridge priority. Which port will
act as the STP root port if all links are operating at the same bandwidth?
Fa0/1 interface of S1
Fa0/2 interface of S1
Fa0/1 interface of S2
Fa0/2 interface of S2
9
Top of Form
What impact does the use of the mdix auto configuration command have on an Ethernet
interface on a switch?
automatically detects duplex settings
10
Top of Form
Refer to the exhibit. Which two facts can be confirmed by this output? (Choose two.)
This switch shows no configuration revision errors.
This switch has established two-way communication with the neighboring devices.
This switch is configured to advertise its VLAN configuration to other VTP-enabled
switches in the same VTP domain.
This switch will drop all VTP advertisements that come from the switches that are
configured in the same VTP domain.
This switch will cause no disruption in the VTP domain operations if the rest of the switches
in the same VTP domain have a higher configuration revision number.
11
Top of Form
Refer to the exhibit. A network administrator enters the displayed commands to configure VLAN
30. What is the result of running these commands?
VLAN 30 will be added to S1, S2, and S3, but not to S4.
12
Top of Form
Refer to the exhibit. A new host needs to be connected to VLAN 20. Which IP address should be
assigned to this new host?
172.16.10.68 /27
172.16.10.99 /28
172.16.10.110 /27
172.16.30.96 /27
172.16.30.120 /28
172.16.30.146 /27
13
Top of Form
What VLANs are allowed across a trunk when the range of allowed VLANs is set to the default
value?
All VLANs will be allowed across the trunk.
The switches will negotiate via VTP which VLANs to allow across the trunk.
14
Top of Form
Refer to the exhibit. RTB is configured for traditional inter-VLAN routing. RTB can ping
computer A but cannot ping computer B. What is a possible cause of this failure?
Port Fa0/11 is in the wrong VLAN.
After reading the destination address, the switch immediately forwards a frame.
The switch receives the complete frame and stores it in buffers before forwarding it.
The switch analyzes the frame for information about its destination. After confirming the
integrity of the frame, the switch forwards it out the correct port.
Bottom of Form
16 Top of Form
After listening for the presence of a signal on the network media, hosts A and C transmit data at the same tim
In what two ways do the hosts respond to this situation? (Choose two.)
The hosts transmit a jam signal to ensure that all hosts on the network are aware that a collision has occu
Because they are operating in full-duplex mode, the hosts resume listening for traffic in preparation for
sending future messages.
Because the hub will temporarily block traffic from one of the hosts, that host will be allowed to transmi
once the wire is clear.
Hosts A and C are assigned shorter backoff values to provide them priority to access the media for
retransmission.
After the backoff period of a host, the host checks to determine if the line is idle before retransmitting.
Bottom of Form
17
Top of Form
Refer to the exhibit. Computer A sends a broadcast message. Which devices will see the
broadcast?
computer B
PoE
port security
link aggregation
application based filtering
Bottom of Form
19
Top of Form
After unpacking a new Linksys WRT300N wireless multifunction device, a user needs to change
the default administrator password and make other configuration changes. What must the user do
to access the device in order to make these changes?
Use a wireless client to associate with the WRT300N and then open a HyperTerminal
session with the device.
Establish a wired connection with the device and then reboot the attached computer to
launch the configuration software.
Establish a wired connection from a computer in the same IP subnet as the WRT300N and
enter the default IP address of the device into a web browser on the computer.
Modify the TCP/IP properties of the computer that is connected to the WRT300N so that the
computer and the WRT300N exist on the same network. Then reboot the computer to
establish a connection.
20
Top of Form
A wireless LAN access point will convert traffic between which two frame encapsulation types?
802.1 and 802.11
VLAN traffic is processed on the subinterfaces even if Fa0/0 line protocol goes down.
The router uses a unique MAC address on VLAN 10 and 20 by adding the 802.1Q VLAN
ID to the hardware address.
Traffic inbound on this router is processed by different subinterfaces depending on the
VLAN from which the traffic originated.
22
Top of Form
Which service should be disabled on a Cisco switch or router to prevent packet sniffers from
capturing information about the device?
SSH
VTP
CDP
SNMP
23
Top of Form
What is the correct order in which the STP components are chosen?
designated ports, nondesignated ports, root bridge, root ports
nondesignated ports, designated ports, root ports, root bridge
Refer to the exhibit. Which statement is true regarding the information shown?
Only one VLAN is currently configured to use the trunk links.
The switch negotiated trunk links for interfaces Fa0/1 and Gi0/1.
Interfaces Gi0/1 and Fa0/1 are allowed to carry data from multiple VLANs.
25
Top of Form
A network administrator enables sticky learning on all access mode interfaces of a Catalyst
switch, saves the configuration, then connects hosts to the switch. After the switch operates for
several days, the administrator reboots the switch without saving the running configuration.
What is the result?
All previously learned MAC addresses are lost.
It is calculated based on the utilization of all the switches along a given path.
It is calculated based on the bridge priority of the switches along a given path.
It is calculated based on the sum of the port cost value, determined by link speed, for each
switch port along a given path.
27
Top of Form
Which configuration changes will increment the configuration revision number on the VTP
server?
configuring trunk links on the VTP server
flash
NVRAM
RAM
30
Top of Form
Which statement regarding the service password-encryption command is true?
The service password-encryption command is entered at the privileged EXEC mode
prompt.
The service password-encryption command encrypts only passwords for the console and
VTY ports.
The service password-encryption command encrypts all previously unencrypted passwords
in the running configuration.
To see the passwords encrypted by the service password-encryption command, enter the
no service password-encryption command.
31
Top of Form
In setting up a wireless infrastructure network, which device is used to associate a client
computer to the network?
an Ethernet switch
Refer to the exhibit. What three statements describe why Host1 and Host2 are unable to
communicate? (Choose three.)
The switch ports are on different VLANs.
The host default gateway addresses must be on the same logical network.
33
Top of Form
Refer to the exhibit. Router R-West and switch S-West1 are connected via a single ethernet cable
between the router interface fa0/0 and the switch interface fa0/1. The router and switch have
been configured with the commands that are displayed in the exhibit. The network administrator
enters the show interfaces trunk command and receives the output as shown. What is the cause
of the "not-trunking" status for switch port Fa0/1?
The trunk is established, but no VLANs have been configured to use it.
The router is missing the dynamic trunking protocol statements necessary to form a trunk.
Because the router does not support Dynamic Trunking Protocol, the trunk has not been
established.
The router, the switch, or both must be configured with the dynamic desirable option for
Dynamic Trunking Protocol to establish a trunk.
34
Top of Form
Refer to the exhibit. The switches in the exhibit have VTP pruning enabled. What will be pruned
in the VTP advertisements from switch ST-C to switch ST-1?
VLAN 30
Frames are always forwarded to the native VLAN when exiting a trunk.
Frames are forwarded to the correct VLAN based on the source IP address.
Frames are forwarded to the correct VLAN based on information in the MAC address table.
36
Top of Form
When port security is used on a switch, which violation mode will cause an SNMP trap to be
sent and traffic to be dropped when the number of secure MAC addresses for a port is reached?
sticky
protect
restrict
Shutdown
37
Top of Form
Refer to the exhibit. The network administrator is planning five additional VLANs to be shared
throughout the VTP domain on S3. What action should the administrator take before creating the
additional VLANs?
Create the VLANs on a switch in VTP server mode and allow them to propogate to the other
switches in the domain.
Modify the configuration revision to 10 to support the additional VLANs.
Enable the VTP pruning mode in order to create the VLANs on S3.
Enable the VTP v2 mode.
38
Top of Form
What identifier in the BPDU creates a unique BID for a switch?
IP address
MAC address
bridge priority
VLAN ID
port priority
39
Top of Form
Refer to the exhibit. The switches have been configured as shown. The hosts that are connected
to switch 101-2FL are not able to communicate with the hosts in their corresponding VLANs
that are connected to switch 101-3FL. What should be done to fix the problem?
Configure port Fa0/2 on switch 101-3FL as a static trunk link.
Introduce a Layer 3 device or a switch with Layer 3 capability into the topology.
Utilize the switchport trunk allowed vlan all command on switch 101-3FL to permit the
VLAN traffic.
Apply IP addresses that are in the same subnet to the interfaces that are used to connect
switches 101-2FL and 101-3FL.
40
Top of Form
Refer to the exhibit. The network administrator enters the configuration shown to allow both
SSH and Telnet connections to the switch. The Telnet connections fail. What is the most likely
cause of this problem?
The SSH version number is wrong.
Refer to the exhibit. Users complain that they do not have connectivity to the web server that is
connected to SW1. What should be done to remedy the problem?
Allow all VLANs on the trunk link.
Refer to the exhibit. How is port Gi1/1 on SWT-A functioning in the spanning-tree topology?
It is sending and receiving data frames.
It is receiving BPDUs and populating the MAC address table, but not sending data.
44
Top of Form
Which three statements are correct concerning the default configuration of a new switch?
(Choose three.)
Spanning Tree Protocol is disabled.
The switch with the highest priority will be assigned the lowest BID in the root election.
The first step in the spanning-tree election process is to determine the root port.
To select designated ports, the spanning-tree algorithm must determine the longest
contiguous path from the root bridge.
46
Top of Form
Refer to the exhibit. What is the purpose of the configuration commands that are shown?
to activate port Fa0/10
Refer to the exhibit. Which password allows the administrator to enter the privileged exec mode?
cisco1
cisco2
cisco3
cisco
48
Top of Form
Refer to the graphic. In the Wireless menu option of a Linksys integrated router, what does the
Network Mode option Mixed mean?
The router supports encryption and authentication.
Refer to the exhibit. The VTP domain has been configured as shown in the exhibit. None of the
configured VLANs on SW1 and SW2 are present on SW3. What should be done to remedy the
problem?
Reconfigure switches SW2 and SW3 in VTP transparent mode.
Reconfigure all switches as VTP clients to synchronize the VLAN database information.
Reconfigure the VTP server as a VTP client and then return to VTP server mode to reset the
configuration revision number.
50
Top of Form
Refer to the exhibit. After receiving a console notification on Switch2, the network administrator
begins to troubleshoot the trunk link between Switch1 and Switch2. Which configuration change
can be made to correct the problem with the trunk link?
Set the Fa0/1 interface on Switch2 to trunk mode.