Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Hydrocontrohc D25
Hydrocontrohc D25
HC-D25
INTRODUCTION - INTRODUZIONE
HC-D25 control valve belongs to the wide range of Il distributore HC-D25 fa parte della vasta gamma della val-
Hydrocontrol S.p.A. modular sectional valves and is capable vole componibili della Hydrocontrol S.p.A. ed è idoneo a fun-
of working with a maximum flow of 380 litres/min. at an ope- zionare con una portata massima di 380 litri/min. a una pres-
rating pressure of 350 bar. sione di esercizio di 350 bar.
Numerous integrated valve features in addition to countless L’elevato numero di funzioni integrate all’interno del distribu-
configuration options make HC-D25 highly flexible and tore, nonché le innumerevoli configurazioni possibili, fanno
easily adaptable to the widest applications range. di HC-D25 un prodotto altamente flessibile e facilmente
adattabile ai più diversi campi applicativi.
Sections are equipped with auxiliary valves and a wide
variety of interchangeable spools. Le sezioni sono corredate di valvole ausiliarie e di un’ampia
gamma di cursori intercambiabili.
The specifications detailed in this catalogue show standard products. Special I dati riportati all’interno del catalogo sono riferiti al prodotto standard. Sono
applications are available to order subject to contacting our Engineering possibili applicazioni speciali da concordarsi previamente con il n/s Ufficio
Department for an estimate. This catalogue is not open to interpretation and Tecnico. Il presente catalogo non va interpretato e nel dubbio chiedere delu-
in case of doubt the costumer is requested to contact the Hydrocontrol cidazioni all’ufficio Tecnico Commerciale Hydrocontrol. I dati riportati non
Technical Sales Office who will be pleased to supply detailed explanations. sono impegnativi e la Hydrocontrol S.p.A. si riserva di apportare modifiche e
The data and specifications indicated are to be considered a guide only and miglioramenti senza preavviso.
Hydrocontrol S.p.A. reserved the right to introduce improvements and modifi-
cations without prior notice.
Hydrocontrol in not responsable for any damage caused by an incorrect use Il costruttore non risponde dei danni arrecati a persone o cose derivanti da un
of the product. uso improprio del prodotto.
1
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
GENERAL SPECIFICATIONS - CARATTERISTICHE GENERALI
• MAX PRESSURE ON (T) . . . . . . . . . . . . . . . . . 290 PSI • PRESSIONE MAX SULLA LINEA (T) . . . . . . . . .20 bar
• CONTAMINATION LEVEL . . . . . . . . . . . 19/16 ISO 4406 • GRADO DI CONTAMINAZIONE . . . . . .19/16 ISO 4406
TYPE OF FLUID TEMP. (C°) GASKET TIPI DI FLUIDI TEMP. (C°) GUARNIZIONI
(Oil and Solution) min max NBR VITON(*) (Oli e Soluzioni) min max NBR VITON(*)
Mineral oil Olio minerale
HPL (DIN 51524) -25 +80 • • HPL (DIN 51524) -25 +80 • •
Oil in water Olio in emulsione
emulsion HFA(*) +5 +55 • • acquosa HFA(*) +5 +55 • •
Water in oil Acqua in emulsione
emulsion HFB(*) +5 +55 • • oleosa HFB(*) +5 +55 • •
Polyglycol-based Soluzione acquosa in
aqueous sol. HFC(*) -25 +60 • poliglicoli HFC(*) -25 +60 •
Ester of phosphoric Esteri di acido
acid HCD(*) -20 +150 • fosforico HCD(*) -20 +150 •
(*) : for this application, please contact our technical sales office. (*) : previo accordo con il n/s Ufficio Tecnico - Commerciale
NBR : nitrile rubber compatible with mineral-bases oils ASTIM 1 NBR : mescola nitrilica compatibile con oli a base minerale ASTIM 1
VITON : fluorinated elastomer for use at high temperature, compatible with VITON : elastomero florurato per impieghi ad alta temperatura, compatibile
fluids ASTIM 1 and ASTIM 3. con fluidi ASTIM 1 e ASTIM 3.
General index
Order modality. . . . . . . . . . . . . . . . . . . . . . . . . . . . pag 4
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pag 6
Hydraulic specifications . . . . . . . . . . . . . . . . . . . . . pag 8
Typical curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . pag 9
Inlet section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pag 11
Work section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pag 14
Spool type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pag 14
Spool actuation . . . . . . . . . . . . . . . . . . . . . . . . . . . pag 17
Spool return action . . . . . . . . . . . . . . . . . . . . . . . . pag 19
Work section type . . . . . . . . . . . . . . . . . . . . . . . . . pag 20
Auxiliary valves . . . . . . . . . . . . . . . . . . . . . . . . . . . pag 20
Intermediate sections . . . . . . . . . . . . . . . . . . . . . . pag 22
Outlet section . . . . . . . . . . . . . . . . . . . . . . . . . . . . pag 27
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pag 30
Installation and maintenance . . . . . . . . . . . . . . . . . pag 31
SECTIONAL VALVE
DISTRIBUTORE COMPONIBILE
Indice generale
Modalità di ordinazione . . . . . . . . . . . . . . . . . . . . . pag 4
Dimensioni . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pag 6
Specifiche idrauliche . . . . . . . . . . . . . . . . . . . . . . . pag 8
Curve caratteristiche . . . . . . . . . . . . . . . . . . . . . . . pag 9
Collettore entrata. . . . . . . . . . . . . . . . . . . . . . . . . . pag 11
Sezione di lavoro. . . . . . . . . . . . . . . . . . . . . . . . . . pag 14
Tipologia cursore . . . . . . . . . . . . . . . . . . . . . . . . . . pag 14
Comando cursore . . . . . . . . . . . . . . . . . . . . . . . . . pag 17
Richiamo cursore . . . . . . . . . . . . . . . . . . . . . . . . . pag 19
Tipologia sezione di lavoro . . . . . . . . . . . . . . . . . . pag 20
Valvole ausiliarie . . . . . . . . . . . . . . . . . . . . . . . . . . pag 20
Collettori intermedi . . . . . . . . . . . . . . . . . . . . . . . . pag 22
Collettori di scarico . . . . . . . . . . . . . . . . . . . . . . . . pag 27
Accessori. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pag 30
Installazione e manutenzione . . . . . . . . . . . . . . . . pag 31
3
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
ORDER MODALITY - MODALITÀ DI ORDINAZIONE
A B C D
pag. 11 pag. 14 pag. 27
USCITA
SEZIONE DI LAVORO
OUTLET
ENTRATA
WORK SECTION
INLET
Tie rod kit allows the correct assembling of HC-D25. Tie Il corretto allestimento del distributore componibile HC-D25
rods lenght depends on number of sections. è garantito dal kit tirante caratterizzato dalla lunghezza
variabile a seconda del numero delle sezioni.
NOTE: each valve is assembled with N° 4 tie rod kits inclu- NOTA: ogni distributore è allestito con N° 4 kit tiranti i quali,
ding a tie rod, two nuts and two washers. a loro volta, sono costituiti da un tirante due dadi e
due rondelle.
5
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
DIMENSIONS - DIMENSIONI
INLET
INGRESSO (P)
OUTLET
SCARICO (T)
PNEUMATIC PILOT
PILOTAGGIO PNEUMATICO
HYDRAULIC PILOT
PILOTAGGIO IDRAULICO
PORTS thread - filettature (BSP) thread - filettature (SAE UN-UNF) thread - filettature (METRICA)
UTILIZZI ISO-228 ISO-725 ISO-262
164.8
136
95 76.5 74 74 76.5
56
Ø 13
T B B B
230
143
200
427.5
P
A A A
Ø 13
Ø 13
72.5
Extracorsa floating
°
126
1"1/4 GAS
17°
38
36 36
15 42 14 12 (X) 12
71 (Y)
WEIGHTS - PESI
7
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
HYDRAULIC SPECIFICATIONS - SPECIFICHE IDRAULICHE
A B A B A B
T P
RP RP RP
A B A B A B
T P
RP RT RP
Carry-over connection (HPCO) Collegamento carry-over (HPCO)
This option, available on all HC-D25, allows the monoblock Questa opzione, di serie sul distributore HC-D25, permette il
to feed a second valve, by extending the free flow channel. prolungamento del canale di libera circolazione all’esterno,
In this configuration, the valve needs a separated port for alimentando così un secondo distributore.
the connection to tank. Il distributore così configurato necessita di uno scarico per le
utenze.
IT IS POSSIBLE TO TRANSFORM SECTIONAL VALVE LA TRASFORMAZIONE DA VERSIONE STANDARD A
FROM STANDARD TO HPCO VERSION JUST BY ORDE- VERSIONE CON COLLEGAMENTO CARRY-OVER
RING THE APPROPRIATE CONIC PLUGS HPCO, È POSSIBILE ORDINANDO 2 TAPPI CONICI
1/2” x 17 (CODE 413010201) 1/2” x 17 (CODICE 413010201)
T AB AB AB
P
HPCO CONIC PLUG POSITION
POSIZIONE TAPPO CONICO
(413010201)
362,5 25 D25/9
290 20
D25/6
217,5 15
145 10 D25/3
72,5 5
D25/1
0 0
0 80 160 240 320 400 l/min
Qp
0 21.1 42.2 63.4 84.6 105.7 US-GPM
174 12
130,5 9
87 6
43,5 3
0 0
0 80 160 240 320 400 l/min
Qp
0 21.1 42.2 63.4 84.6 105.7 US-GPM
435 30 D25/9
362,5 25
D25/6
290 20
D25/3
217,5 15
145 10 D25/1
72,5 5
0 0
0 80 160 240 320 400 l/min
Qp
0 21.1 42.2 63.4 84.6 105.7 US-GPM
2175 150
1450 100
725 50
0 0
0 80 160 240 320 400 l/min
0
Qp
21.1 42.2 63.4 84.6 105.7 US-GPM
NOTE: indicated values have been tested with standard NOTA: i valori indicati sono stati rilevati con un distributore
sectional valve and W001A spools. in configurazione standard e cursori W001A.
9
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
TYPICAL CURVES - CURVE CARATTERISTICHE
174 12 217.5 15
116 8 145 10
58 4 72.5 5
0 0 0 0
0 80 160 240 320 400 l/min 0 80 160 240 320 400 l/min
Qp Qp
0 21.1 42.2 63.4 84.6 105.7 US-GPM 0 21.1 42.2 63.4 84.6 105.7 US-GPM
0.47 12
0.39 10
0.31 8
0.23 6
0.15 4
0.07 2
0 0
0 5 10 15 20 25 30 bar
∆p
0 72,5 145 217,5 290 362,5 435 psi
NOTE: the graphic show the spool stroke as a function of NOTA: il grafico presenta lo spostamento del cursore in fun-
the pressure operating. zione della pressione di comando.
RELIEF VALVE
VALVOLA DI MASSIMA
(150) setting direct acting pressure valve . . .page 14 (150) taratura valvola di massima . . . . . . . . .pag. 14
A G07 inlet and thread position . . . . . . . . . . . .page 15 A G07 posizione ingresso e filettatura . . . . . . .pag. 15
IL
IR
11
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
INLET ARRANGEMENT - ALLESTIMENTO ENTRATA
3 T P
Sede valvola con
tappo
6 T P
Valvola con
pilotaggio esterno
009 010 011 016 018 019 020 021 022 027 029 030 031 032
2A-3B 2A-4B 2A-6B 2A-11B 3A-2B 3A-3B 3A-4B 3A-51B 3A-6B 3A-11B 4A-2B 4A-3B 4A-5B 4A-6B
037 038 039 040 045 047 049 050 052 085 086 087 088 089
4A-11B 5A-13B 5A-4B 5A-6B 5A-11B 6A-2B 6A-4B 6A-5B 6A-11B 11A-2B 11A-3B 11A-4B 11A-5B 11A-6B
13
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
WORK SECTION - SEZIONE DI LAVORO
VALVE PLUGGED
SEDE VALVOLA CON TAPPO
ANTISHOCK VALVE
VALVOLA ANTIURTO
LEVER ACTUATION
COMANDO LEVA
SPOOL
CURSORE
H101 spool actuation type . . . . . . . . . . . . . . .page 17 H101 tipologia comando cursore . . . . . . . . . . .pag. 17
F001A spool return action type . . . . . . . . . . . .page 18 F001A tipologia richiamo cursore . . . . . . . . . . .pag. 18
RP G07 type and thread section . . . . . . . . . . . .page 20 RP G07 tipologia sezione e filettatura . . . . . . . .pag. 20
01PA auxiliary valve (port A) . . . . . . . . . . . . .page 20 01PA valvola ausiliaria (utilizzo A) . . . . . . . . .pag. 20
B o A 3 positions double-acting
3 posizioni doppio effetto
W001
T P
B o A
3 positions double-acting A and B to tank
3 posizioni doppio effetto A e B a scarico
W002
T P
B o A
3 positions double-acting A to tank B blocked
3 posizioni doppio effetto A scarico B bloccato
W003
T P
B o A
3 positions double-acting A blocked B to tank
3 posizioni doppio effetto A bloccato B scarico
W004
T P
o A
3 positions single-acting on A
3 posizioni semplice effetto in A
W005
T P
B o
3 positions single-acting on B
3 posizioni semplice effetto in B
W006
T P
o A
3 positions single-acting on A (A to tank)
3 posizioni semplice effetto in A (A a scarico)
W007
T P
B o
3 positions single-acting on B (B to tank)
3 posizioni semplice effetto in B (B a scarico)
W008
T P
B o A 3 positions double-acting with anticavitation valves
3 posizioni doppio effetto con valvole anticavitazione
W009
T P
B o A 3 positions double-acting switch port closed (A and B blocked)
3 posizioni doppio effetto senza passaggio in O (A e B bloccati)
W010
T P
B o A 3 positions double-acting switch port closed (A and B to tank)
3 posizioni doppio effetto senza passaggio in O (A e B scarico)
W011
T P
B o A 4 positions double-acting with float in the 4th position
4 posizioni doppio effetto (4° posizione flottante)
W012
T P
B o A
3 positions double-acting regenerative
3 posizioni doppio effetto rigenerativo
W013
T P
B o A 3 positions double-acting series
3 posizioni doppio effetto serie
W015
T P
B o A 3 positions double-acting series A and B to tank
3 posizioni doppio effetto serie A e B a scarico
W016
T P
B o A 3 positions double-acting series A to tank B blocked
3 posizioni doppio effetto serie A a scarico B bloccato
W017
T P
B o A 3 positions double-acting series B to tank A blocked
3 posizioni doppio effetto serie A bloccato B a scarico
W018
T P
NOTA: l’impiego dei cursori W012, W013 richiede l’utilizzo NOTE: W012, and W013 spools need a special machining
di un corpo con lavorazione speciale. on the valve body.
15
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
SPOOL TYPE - TIPOLOGIA CURSORE
A B
W001A
Spool 3 positions double-acting Cursore 3 posizioni doppio effetto
STANDARD STANDARD
W001B
Spool 3 positions double-acting Cursore 3 posizioni doppio effetto
METERED PARZIALIZZATO
Spools with restricted service ports Cursori con utilizzi a scarico controllato
W002A J10
Restriction on diameter (0,10 mm in A and B)
Alleggerimento sul diametro (0,10 mm in A e B)
Allen wrench 6 - 25 Nm
Chiave 6 - 25 Nm
Hydraulic actuation
Comando idraulico
H005
NOTE: leave out the spool return action code NOTA: omettere la sigla del richiamo cursore
113
Allen wrench 6 - 25 Nm
Chiave 6 - 25 Nm
42
42
95
Unprotected lever
Comando leva non protetta
H101
Ø 12
73
86
17
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
SPOOL RETURN ACTION - RICHIAMO CURSORE
Spool return kits have three different spring types; following I kit richiamo cursore si differenziano in tre tipologie di molle,
the codes depending on spring loads: a seconda del valore di carico:
Precarico
Preloading
K2(N)
Fine corsa
K1(N)
End of stroke Corsa - Stroke
0 100%
A B C
F001A
3 positions spring-centred spool 3 posizioni ritorno al centro a molla
(standard spring) (molla standard)
F001B
3 positions spring-centred spool 3 posizioni ritorno al centro a molla
(soft spring) (molla tenera)
F001C
3 positions spring-centred spool 3 posizioni ritorno al centro a molla
(heavy spring) (molla dura)
Allen wrench 6 - 25 Nm
Chiave 6 - 25 Nm
71,5
Allen wrench 6 - 25 Nm
Chiave 6 - 25 Nm
124,5
19
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
WORK SECTION TYPE - TIPOLOGIA SEZIONE DI LAVORO
01PA 01PB
port - utilizzo (A) port - utilizzo (B)
02PA 02PB
port - utilizzo (A) port - utilizzo (B)
03PA 03PB
port - utilizzo (A) port - utilizzo (B)
04PA 04PB
port - utilizzo (A) port - utilizzo (B)
05PA 05PB
port - utilizzo (A) port - utilizzo (B)
NOTE: sections designed to house auxiliary valve option NOTA: le sezioni predisposte per le valvole ausiliarie obbli-
require double choice on work ports A and B. gano la doppia scelta sugli utilizzi A e B.
Always indicate setting value when using antishock auxiliary Indicare sempre il valore di taratura, nel caso di scelta della
valves and cambinated valves: valvola antiurto e della valvola combinata:
SETTING AT FULL FLOW = 01 PA 120 TARATURA PASSAGGIO = 01 PA 120
SETTING AT MIN. FLOW = 01 PA 120-A TARATURA APERTURA = 01 PA 120-A
21
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
INTERMEDIATE SECTIONS - COLLETTORI INTERMEDI
RELIEF VALVE
VALVOLA DI MASSIMA
BE intermediate inlet section type . . . . . . .page 22 BE tipologia collettore intermedio entrata . .pag. 22
(150) setting direct acting pressure valve . . .page 23 (150) taratura valvola di massima . . . . . . . . .pag. 33
A G07 inlet and thread position . . . . . . . . . . . .page 24 A G07 posizione ingresso e filettatura . . . . . . .pag. 34
Classificazione Classification
HYDRAULIC DIAGRAM LAYOUT DESCRIPTION + CODE
SCHEMA IDRAULICO CONFIGURAZIONE DESCRIZIONE + SIGLA
Entrata - Inlet (P1) INTERMEDIATE INLET
Uscita - Outlet (T) Entrata - Inlet (P) SECTION
T P COLLETTORE INTERMEDIO
DI ENTRATA
P1 BE
INTERMEDIATE SECTION
Uscita - Outlet (T) Entrata - Inlet (P)
WITH PRESSURE RELIEF VALVE
COLLETTORE INTERMEDIO
T P CON VALVOLA DI MASSIMA
BV*
(*) Omit the code for inlet positioning and type of thread (*) Omettere la sigla del posizionamento ingresso e filettatura
TYPE V TIPO V
The intermediate inlet section and the elements are driven L’intermedio di entrata e gli elementi sono alimentati da
by a single pump (P). The downstream elements can be set un’unica pompa (P). Gli elementi a valle del collettore inter-
to a lower pressure than those the upstream one by adju- medio, possono essere tarati ad una pressione inferiore
sting the pressure relief valve of the intermediate section in degli elementi a monte agendo sulla valvola di massima del
question. collettore intermedio in oggetto.
Pilot operated
Main anticavitation
pressure relief
check valve
valve
2 T P
Valvola di
massima
4 T P
Valvola
anticavitazione
generale
pressione pilotata
3 T P
Sede valvola con
tappo
11 P
x Sede valvola con
tappo attacco
manometro
009 010 016 018 019 027 029 030 037 085 086 087 201
2A-3B 2A-4B 2A-11B 3A-2B 3A-3B 3A-11B 4A-2B 4A-3B 4A-11B 11A-2B 11A-3B 11A-4B 1A
23
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
INTERMEDIATE SECTIONS - COLLETTORI INTERMEDI
Complete configuration samples for HC-D25 with intermediate inlet section (BE)
Esempio di configurazione completa di un distributore HC-D25 con intermedio di entrata (BE)
HC-D25/2
Right inlet section .......................................IR 009 150 A G07 .............................Collettore entrata destra
Working section .................................W001A H101 F001A RP GO7 ...............................Sezione di lavoro
Intermediate inlet section ...........................BE 009 120 A G07 ..................Collettore intermedio di entrata
Working section .................................W001A H101 F001A RP GO7 ...............................Sezione di lavoro
Outlet section....................................................TJ A GO8 ..........................................Collettore di scarico
PLUG KIT
TAPPO DI CHIUSURA
PLUG KIT
TAPPO DI CHIUSURA
BF intermediate outlet section type . . . . . .page 25 BF tipologia collettore intermedio uscita . . .pag. 25
A G08 outlet and thread position . . . . . . . . . . .page 26 A G08 posizione ingresso e filettatura . . . . . . .pag. 26
Classification Classificazione
HYDRAULIC DIAGRAM LAYOUT DESCRIPTION + CODE
SCHEMA IDRAULICO CONFIGURAZIONE DESCRIZIONE + SIGLA
Uscita - Outlet (T) INTERMEDIATE OUTLET
T Entrata - Inlet (P1) Entrata - Inlet (P) SECTION WITH SINGLE TANK RETURN
COLLETTORE INTERMEDIO
P P DI SCARICO AD 1 USCITA (T)
BF
T BG
TYPE G TIPO G
The section in question allows the flow of oil of the two Il collettore in oggetto permette di convogliare il flusso d’olio
pumps to be piped in two outlets: delle due pompe in due uscite:
- HPCO for powering another directionale control valve - HPCO per l’alimentazione di un altro distributore
- T for discharge of the work ports - T per lo scarico delle utenze
In order to obtain this, the two T need to be linked. Per ottenere ciò è necessario collegare le due T.
25
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
INTERMEDIATE SECTIONS - COLLETTORI INTERMEDI
BF
Uscita - Outlet (T)
Upper inlet
Ingresso superiore
BG
Upper outlet HPCO - front side A and rear side B to T Uscita - Outlet (HPCO)
Uscita superiore HPCO - anteriore lato A e posteriore lato B in T
Uscita - Outlet (T)
Complete configuration samples for HC-D25 with intermediate outlet section (BF)
Esempio di configurazione completa di un distributore HC-D25 con intermedio di uscita (BF)
Intermedio Uscita - Intermediate section
Collettore Entrata - Intlet Section
PLUG KIT
TAPPO DI CHIUSURA
PLUG KIT
TAPPO DI CHIUSURA PLUG KIT
TAPPO DI CHIUSURA
A G08 outlet and thread available . . . . . . . . . .page 28 A G08 posizione scarico e filettatura . . . . . . . .pag. 28
PLUG KIT
TAPPO DI CHIUSURA
PLUG KIT
TAPPO DI CHIUSURA PLUG KIT
TAPPO DI CHIUSURA
CONIC PLUG
TAPPO CONICO
M G08 outlet and thread available . . . . . . . . . .page 29 M G08 posizione scarico e filettatura . . . . . . . .pag. 29
27
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
OUTLET SECTION - COLLETTORE DI SCARICO
TJ
Entrata - Inlet (P) Uscita - Outlet (T)
OUTLET SECTION
WITH SINGLE RETURN (T)
LEFT-SIDE INLET (P)
P T COLLETTORE DI SCARICO
AD 1 USCITA (T)
ENTRATA SINISTRA (P)
TK
Outlet and thread available Tipologia scarico e filettatura
Upper inlet (T)
Ingresso superiore
Central outlet
Uscita centrale
TM
Uscita - Outlet (T)
T Entrata - Inlet (P) Uscita - Outlet (HPCO) OUTLET SECTION WITH TWO RETURNS
LEFT-SIDED INLET (P)
TN
Outlet and thread available Tipologia scarico e filettatura
(HPCO)
HPCO upper outlet T (TANK) side outlet B
(T)
HPCO uscita superiore T (TANK) uscita posteriore lato B
29
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
FEATURES - ACCESSORI
M14
Φ14
ZA M14 350
Lever lenght mm
Lunghezza asta leva in mm
Lever thread
Filettatura asta leva
Lever type
Tipologia asta leva
F A
E
D C
60 Nm 60 Nm 60 Nm
ANTISHOCK VALVE CAP ANTICAVITATION VALVE CAP COMBINATED VALVE CAP
CORPO VALVOLA ANTIURTO CORPO VALVOLA ANTICAVITAZIONE CORPO VALVOLA COMBINATA
60 Nm 120 Nm 120 Nm
31
Sectional Valve - DISTRIBUTORE COMPONIBILE 32
HCD25-03
HC-D25
INSTALLATION AND MAINTENANCE - INSTALLAZIONE E MANUTENZIONE
SERIAL NUMBER
MATRICOLA DI PRODUZIONE
CONFIGURATION CODE
CODICE DISTRIBUTORE
Recommended curve for our standard directional control Curva consigliata per i nostri distributori standard A01 (vedi
valves A01 ( see remote controls catalogue). catalogo manipolatori).
Entrata - Inlet (P) Uscita - Outlet (T) Uscita - Outlet (T) Entrata - Inlet (P)
Sectional valve with left inlet (IL) Sectional valve with right inlet (IR)
Distributore con entrata sinistra (IL) Distributore con entra destra (IR)