Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Section:
Registration no:
DEPARTMENT OF TECHNOLOGY
Preface
This lab course is designed to provide basics understanding for strength of commonly
used materials with practical knowledge in field of Civil Technology at undergraduate
level. Students will apply the knowledge gained from theoretical to practical application.
Procedures outlining each fieldwork have been comprehensively covered. It is hoped
that students will gain valuable knowledge after completion of this strength of material
lab course, which will also help them in their field work.
Acknowledgment
The author highly indebted to his HOD and colleagues for their constant support and
guidance during the course of preparing strength of material lab manual. In addition,
thanks to the students for the pictures were collected from the laboratory.
List of Experiments
1. Layout of mechanics of solids laboratory
10. To determine the shear modulus and shear stress for a given shaft
using torsion apparatus.
Date of Performance
Date of
Sr.# Experiments
Performance
1 Layout of mechanics of solids laboratory
2 To Study Small Instruments
EXPERIMENT NO. 01
“LAYOUTOF MECHANICS OF SOLIDS LAB.”
Significance:
The significance to draw the layout plan of mechanics of solids lab is to have an
idea about location of machines in the laboratory and also to get important
information about the machines, so that one can easily use them.
Lab Accessories:
1) Charpy’s impact testing machine
2) Unsymmetrical Bending apparatus
3) Universal testing machine (UTM) 500KN
4) Gauge length marking tool
5) Column Buckling Apparatus
6) Brinell Hardness Apparatus
7) Torsion Apparatus
8) Beam Deflection Apparatus
9) Hook’s Law Apparatus
10)Izod Impact testing Machine
11)Compression testing Machine
12)Tables
13)Steel cabinet
14)Fatigue testing machine
15)Wooden counter
16)Universal testing machine (UTM) 1000KN
Tension test
Compression test
Bending test
Shear test
Punching test
It has two parts. Its upper part is fixed whereas lower part is moveable. It can perform all
sorts of tests by re arranging its bed.
The University of Lahore Department of 8
Technology
MECHANICS OF SOLIDS Lab 2020
Manual
Its maximum capacity, as mentioned in its name, is 50 Ton. It is China manufactured
machine. It is operated electrically.
Measuring Scale:
0-170 degrees
Bending
Tension
EXPERIMENT NO. 02
“STUDY OF SMALL INSTRUMENTS”
Objective:
To get familiar with small instruments used in several experiments
To measure the diameter, linear dimensions etcetera of small objects
1. VERNIER CALIPER
Purpose:
It is used to measure internal diameter, external diameter, and length of small
objects, depth and thickness of small objects.
VERNIER CALIPER
Parts:
Main scale
Venire scale
Upper jaws
Lower jaws
Depth measuring stem
Screw clamp
Least count:
The smallest measurement, that any instrument can measure, is called least count.
Zero Error:
If zero of main scale is to the left of vernier scale’s zero, subtract the error in the
end from final reading & vice versa.
Mathematically:
Length = Main Scale Reading + (Least Count * Vernier Scale Reading)
Parts:
The University of Lahore Department of 12
Technology
MECHANICS OF SOLIDS Lab 2020
Manual
Main scale (horizontal scale)
Minor scale (micrometer scale, circular scale)
Frame and lock nut.
Ratchet knob.
Anvil and spindle
Least Count:
Pitchof instrument
Least Count =
Total No. of Divisions OnCircular Scale
0.5
¿
50
= 0.01mm
Pitch:
By the Complete rotation of the circular scale on main scale, the circular scale covers a
distance of 0.5mm. This is called pitch.
3. DEFLECTION GAUGE
Deflection:
Any of the displacement from the neutral axis of the member is referred as
deflection.
Purpose:
To measure deflection of any structural member like beam, column and slab etc.
\
DEFLECTION GAUGE
Parts:
Smaller circular scale
Larger circular scale
Least Count:
Inner dial is divided in 10 parts & outer dial is divided in 100 parts.
4. EXTENSOMETER
Purpose:
It is used to measure the elongation in steel, produced during the tension test. It can
measure the maximum value of 25 mm.
EXTENSOMETER
Least Count:
Least count of extensometer = 0.001mm
This is very old instrument. Now day fully electronic extensometers are used which
automatically give readings in digital form.
5. INSIDE CALIPER
It is used to measure the internal dimensions of small objects. It has no least count .
INSIDE CALIPER
The caliper has an adjusting screw that permits it to be carefully adjusted without
removal of the tool from the work piece.
6.OUTSIDE CALIPER
It is used to measure the external dimensions of small objects. It has no least count.
OUTSIDE CALIPER
7. SPRING DIVIDER
SPRING DIVIDER
It is used to measure extension in steel bar during tension test, when the range of
extensometer is exhausted. It has no scale, so no least count.
PRECAUTIONS:
Instruments which we have to use should be clean
The jaws of calipers should be not loose, not so hard tight when specimen
put between them
Reading should be noted carefully
Before observation we should have to check instrument error
EXPERIMENT NO. 03
“TO VERIFY HOOKE’S LAW BY MEASURING THE ELONGATION OF THE
SPRING CAUSED BY THE LOAD ON THE SPRING AND DETERMINING THE
SPRING CONSTANT.”
APPARATUS:
Hooks Law apparatus including a scaled stand, pointer, hanger, weights and springs
EXPERIMENTAL PROCEDURE:
1) Suspend a spring specimen and hang the pan and set pointer on the scale.
2) Note the initial reading A on the scale.
3) Then gradually add load W in the pan and note the corresponding forward scale
reading B1 on each load.
4) Now decrease the load in the same increments and take corresponding backward
scale reading B2.
5) Calculate forward and backward elongations X 1 and X 2 , and then find the average
elongationX .
6) Plot a graph between W andX .
7) Comment on the graph/results. Repeat the experiment with a new spring
specimen.
X 1+ X 2
Average displacement =X =
2
W
Springconstant =k =
X
Spring
Obs Mass Load Reading on scale Elongation
Constant
( kg ) (N) B1 ( mm ) B2 ( mm ) X 1 ( mm ) X 2 ( mm ) X ( mm ) ( N /mm )
PRECAUTIONS:
Instruments which we have to use should be clean
Before observation we should have to check instrument error
Reading should be noted carefully
COMMENTS: -
EXPERIMENT NO. 04
“DETERMINING THE CHARPY’S IMPACT RESISTANCE OF NOTCHED
SPECIMENS OF METALLIC MATERIALS IN;
TENSION
BENDING
ASTM E-23-C”
Apparatus:
The apparatus required for this test is:
Objective:
The basic objective is to determine the modulus of toughness.
Related Theory
Toughness:
Toughness is the resistance of a substance against a sudden impact of load.
OR
The ability of a material to absorb energy and deform plastically without fracture.
Modulus of toughness is defined as energy absorbed per unit volume by the specimen
when it is loaded from zero to failure. Mathematically,
Types of Loads:
a) Dead load/Static load
b) Dynamic load/Live load
c) Impact load
Dead Load/Static Load is the load which does not change its magnitude, direction and
position is termed as static load. Self-weight of a structures or permanent features of
building is called dead weight.
Live Load/Dynamic Load the load which changes its magnitude, direction and position,
or, one of these e.g., moving vehicles on the bridge.
Impact Load is sudden application of large magnitude of force in short interval of time.
e.g., Earthquake load, blast load.
PROCEDURE: -
For Impact Test in Bending:
LABELED DIAGRAM:
The University of Lahore Department of 24
Technology
MECHANICS OF SOLIDS Lab 2020
Manual
θ1-90
h1-ho h2-ho
θ2-90
θ1
θ2
h1ho h2
SOLUTION:
As,
E1= mgh1
E2= mgh2
=-R Cos θ2
= -R Cos θ1
ΔE = E1 – E2
= mgh1 – mgh2
= mg(h1 – h2)
= mg (R Cosθ2 – R Cosθ1)
ΔE
M .O .T =
Volume
CALCULATIONS:
(BENDING)
m = 22.4 Kg
g = 9.81 m/sec2
R = 760mm
θ1= 141˚
θ2 = 119˚
Solution:
ΔE = 48771.99 N-mm
Volume = L x b x d
= 5538.816 mm3
Energy
M .O .T =
Volume
48771.99
M .O .T =
5538.816
(TENSION):
θ1= 141˚
d = 10.25mm
θ2= 90˚
L = 51.5 mm
π d2
Volume= xL = 4249.57 mm3
4
Energy
M .O .T =
Volume
129787.6
M .O .T =
4249.57
Precautions:
COMMENTS: -
EXPERIMENT NO. 05
“TO PERFORM SIMPLE TENSION TEST ON HOT ROLLED MILD STEEL BAR
ASTM A615/615M”
Objectives:
To study the stress-strain behavior of mild steel
To determine the different mechanical properties of steel
To check the adequacy of specimen as per ASTM 615M
APPARATUS:
2) STEEL SPECIMEN
3) VERNIER CALIPER
RELATED THEORY
Stress is directly proportional to the strain, but in concretes it follow-up to some extent
STRESS_STRAIN DIAGRAM
Proportional Limit:
Stress has linear combination with strain. Hook’s law is not valid after
proportional limit. Numerical values of elastic and proportionality limit are
usually identical.
Elastic Limit:
The maximum stress that can be applied to a metal without producing
permanent deformation. If the stresses are not too great the material will return
to its original shape and dimension when the external stress is removed.
Yield Point:
It is point after which there is an increase in strain of the material without any
significant increase of stress. At this point there is reorientation of particles of
material.
Ultimate Strength:
Maximum or highest ordinate on the stress-strain curve is called ultimate
strength. Its maximum strength of the sample.
Necking:
At about the ultimate stress point, the cross-sectional area of the specimen
begins to decrease in a localized region. This phenomenon is called necking.
MODULUS OF ELASTICITY:
It is the slope of stress-strain curve within the proportional limit of the material.
Resilience:
The ability of the material to absorb energy in the elastic region.
Modulus of Resilience:
It is amount of work done on a unit volume of material, as simple tensile force
is increased from zero to proportional limit. It is determined by calculating area
under stress-strain curve from zero up to proportional limit.
Toughness:
The ability of the material to absorb energy in the plastic region.
Modulus of Toughness:
Strain per unit volume up to rupture is called the modulus of toughness. It is
determined by calculating total area under stress-strain curve, from zero to
rupture point.
Residual Strain:
When material is loaded beyond the elastic limit then after unloading the
material does not come back to its original position and there is a permanent
set in the specimen.
Ductile Material:
Material having a relatively large tensile strain up to the point of rupture or
failure is called as ductile material e.g. mild steel.
The University of Lahore Department of 32
Technology
MECHANICS OF SOLIDS Lab 2020
Manual
Brittle Material:
Materials having a relatively small tensile strain up to the point of rupture are
called as brittle materials. E.g. cast iron, concrete, etcetera.
Hauling of Machine:
In the method the machine stops for some time showing yielding stage. It is
the best method for observing yielding in ductile materials.
Offset Method:
For material that doesn’t have any well-defined yield point, yield strength is
determined by offset method. This method consists of drawing a line parallel to
stress-strain curve at 0.2% strain. Where this intersects the stress-strain curve,
at that point stress ordinate is recorded as proof stress. This proof stress is
taken as yield stress.
SPECIFIC STRAIN
METHOD:
In this method, yielding will occur at specific strain and according to standard, it
is 0.5%
Procedure:
In this method and increasing load is applied to the specimen at a uniform rate. The load
at which there is a halt or hesitation of the load indicating pointer is noted and termed the
“yield point”.
The stress at this point is computed and termed the yield stress. Calculate the yield
stress by dividing the load at the “yield point” by the nominal cross-sectional area of the
test specimen.
TENSILE STRENGTH:
Calculate the tensile strength of the Deformed Bar by dividing maximum load that
specimen sustains during tension test by the original cross-sectional area of the
specimen.
ELONGATION:
To determine the percentage of elongation, fit the ends of the fractured specimen.
Elongation is the increase in length of the gage length, join carefully and measure the
distance between the gage marks. This is expressed as a percentage of the original
gage length. In reporting elongation values, give both the percentage increase and the
original gage length.
However, if the elongation is less than the minimum requirement, discard the specimen
and retest a new specimen.
Percentage Elongation:
The change in length per unit original length expressed in percentage.
Lo−Lf
ε= Lo
X100
Where,
Lo = original length
Lf= final length
Ao−Af
ε= Ao X100
Where,
If any part of the fracture takes place outside of the middle half of the gage length or in
the punched or scribed mark within the reduced section, the elongation value obtained
may not be representative of the material. If the elongation measured meets the
minimum requirements specified, no further testing is needed.
PRECAUTIONS:
mm L to R R to L L to R R to L L to R R to L
1 40 42 43 42.5 2.5 6.25 40
2 40 45 46 50 5.5 13.75 40
3 40 42 42 42 2.0 5.00 40
4 40 43 42 42.5 2.5 6.25 40
5 40 40 40 40 0 0 40
6 40 42 44 43 3.0 7.50 40
7 40 46 45 45.5 5.5 13.75 40
8 40 42 41 41.5 1.5 3.75 40
9 40 46 45 45.5 5.5 13.75 40
10 40 41 41 41 1.0 2.5 40
11 40 47 46 46.5 6,5 16.25 40
100
%age Elongation=( Elongation−Gage Length )×
Gage Lengt h
D =?
L = 61 cm
m = 0.965 Kg
ρ = 7850 kg/m3
m
ρ=
v
m
d=
√
π
4
D 2 xL
D = 16 mm
COMMENTS:
EXPERIMENT NO. 06
“TO PERFORM COMPRESSION TEST ON WOODEN CUBES WHEN LOAD IS
APPLIED:
Parallel to Fibers.
Perpendicular to Fibers.
ASTM D-1037”
Objective:
To determine compressive strength of wood.
To determine modulus of elasticity and modulus of stiffness.
To study the anisotropic behavior of wood.
Apparatus:
Universal Testing Machine.
Wooden Cubes
Vernier Caliper
RELATED THEORY
Compressive Strength:
Maximum compressive stress that can be developed in any member is termed as
compressive strength.
Modulus of Elasticity:
It is the ratio b/w the unit stress to unit strain. And it is determined as the slope of the
straight line from zero to proportional limit.
Modulus of Stiffness:
P ∝δ
P = Kδ
Where,
K Is Modulus of Stiffness
Isotropic Material:
Materials showing same properties in different directions are called isotropic
materials e.g. Steel
Anisotropic Material:
Materials showing different properties in different directions are termed as
anisotropic materials e.g. wood.
The strength of the wooden sample when the load is applied parallel to the Fibers is
about ten times more as compare to when the load is applied perpendicular to
Fibers.
Procedure:
The University of Lahore Department of 47
Technology
MECHANICS OF SOLIDS Lab 2020
Manual
Measure All the Dimensions of wooden cube. i.e. Length, Width, Height with the
help of Vernier caliper
Fix the cube in the machine
Gradually keep on increasing the load
Note the load and deflection readings from attached computer
Prepare a graph for it
Repeat the procedure for load applying in perpendicular case.
PRECAUTIONS:
Cube-1 Cube-2
Failure Perpendicular to Fiber Failure Parallel to Fiber
l1 mm l1 mm
l2 mm l2 mm
A mm2 A mm2
Compressed Length mm Compressed Length mm
F F
σ= σ=
A A
σ =¿ kN/m 2
σ =¿ kN/m2
σ =¿ MPa σ =¿ MPa
COMMENTS:
EXPERIMENT NO. 07
“To study the bending behavior of beam and to determine modulus of
elasticity and modulus of rupture. ASTM D-6272”
APPARATUS:
50 TON UTM
DEFLECTION GAUGE
WOODEN BEAM
RELATED THEORY
Shear Force:
A force which tends to slide one part of section against the adjacent part acting normal
to the longitudinal axis and tangentially to the cross section is called shear force.
Bending Moment:
Elastic Curve:
The deflected shape of longitudinal axis of beam is called elastic curve.
Modulus of Elasticity:
It is the ratio of unit stress to unit strain and it is determined as the slope of the straight
line from zero to proportional limit from stress strain diagram. Modulus of elasticity is
given by following relation:
σ= EԐ
Modulus of Rupture:
Maximum tensile/bending stress that can be developed in a beam before failure or it is
the energy absorbed per unit volume when the specimen is loaded from zero to failure
load.
Flexural Formula:
The relationship between flexural stress and bending moment is expressed by flexural
formula and is given as
σ= My/I ------- (1)
Where,
σ= Flexural stress
I=Moment of inertia
Loading Arrangement:
The University of Lahore Department of 51
Technology
MECHANICS OF SOLIDS Lab 2020
Manual
We want such type of loading arrangement that can produce pure moment zone so
that failure is only due to moment not due to combine effect of moment and shear.
This can only be achieved by two-point loading arrangement.
Types of Failure:
a) Shear Failure is the one generated at support and cause diagonal cracks.
b) Flexural Failure is the one generated at the center and cause vertical cracks.
c) Flexural Shear Failure is the one generated between support and center and
cause the cracks which are vertical from the bottom and diagonal from the top.
Procedure:
h=
a=
L=
At Breaking Load P,
Plotting of Graph:
Draw graph between Load and Deflection and get [P’/D] value from the graph that is
the slope of the straight line.
PRECAUTIONS:
COMMENTS:
EXPERIMENT NO. 08
“TO PERFORM HARDNESS TEST ON A GIVEN STEEL SAMPLE USING
BRINELL HARDNESS TESTING MACHINE. ASTM E-10”
Purpose:
To check hardness of sample
To check quality of sample in industry
It gives indirect measure of strength of material
Apparatus:
Brinell Hardness testing Machine
Steel sample
Related Theory:
Hardness:
It is property of material by the virtue of which it resists the plastic
deformation, usually by penetration. However; the term hardness may also
refer to resistance to bending, scratching, abrasion or cutting.
Where,
D=Diameter of indenter
d= Indentation diameter
Applications:
Because of the wide test force range the Brinell test can be used on almost any
metallic material. The part size is only limited by the testing instrument's capacity.
Indenters:
For soft material
10 mm carbide indenter
Load
Mean
Dia. of indentation(d) Load
Sr.NO Ball Dia. Dia.(d) B.H. N
Specimen mm (Kg)
. (mm) (mm)
d1 d2 d3
1 Copper 10
2 Aluminum 10
3 Brass 10
D=diameter of indenter
d= indentation diameter
PRECAUTIONS:
COMMENTS:
EXPERIMENT NO. 09
“TO STUDY COLUMN BUCKLING FOR DIFFERENT END-CONDITIONS.”
Objective:
To find out critical buckling loads
To check applicability of Euler’s Theory
To study various end-conditions of column
Apparatus:
Column buckling apparatus
Vernier calipers
Related Theory:
Column:
Slenderness ratio:
The ratio of the equivalent length of the column to the least radius of gyration is called
the slenderness ratio.
Buckling load:
The minimum axial load at which the column tends to have lateral displacement &
buckle is called the buckling, crippling or critical load.
Equivalent length:
It is the length of the column which gives the same buckling load, as given by a both
ends hinged column.
Short Column:
Medium Column:
A column for which the slenderness ratio lies between 32 and 120 is called a
medium column.
Long Column:
A column for which the slenderness ratio is more than 120 called a long column.
Safe load:
Depending upon the end conditions, there are four types of columns.
E=Modulus of elasticity
Le=KL
End-Conditions:
Procedure:
Find out critical load for each column
Find out column dimensions with Vernier calipers
Calculate critical load
Comparison
Column
Le I Pcr
Dimensions
(mm) (mm4) (N)
Sr. End-
K H
no. conditions B L
(mm)
(mm) (mm)
PRECAUTIONS:
COMMENTS:
EXPERIMENT NO. 10
“TO DETERMINE THE SHEAR MODULUS AND SHEAR STRESS FOR A GIVEN
SHAFT USING TORSION APPARATUS.”
Objective:
To Determine Shear stress
To Determine Shear Modulus
APPARATUS: -
Torsion apparatus, dial gauge, lever, L-key, Weights, test shaft.
Torsion apparatus
RELATED THEORY: -
Torsion is the engineering word used to describe the process of twisting a member
about its longitudinal axis. A torsion test is quite instrumental in determining the value
of modulus of rigidity (ratio of shear stress to shear strain) of a metallic specimen.
Procedure:
Set the clamping distance of the supports at 600 mm and clamp the test shaft at
both ends.
Position the lever and set the dial gauge tip on the lever groove in compressed
form.
Set the gauge scale to Zero.
Note that 1 mm reading of the dial gauge measures 1 °angle of twist.
Now put the load in suitable increments and for each load record the angle of
twist.
Calculate the corresponding values of shear modulus and shear stress.
Repeat the experiment with a new span of 200 mm of the same shaft.
You can also repeat the entire experiment with new test shaft specimen.
span length=L=600 mm
moment arm=R=60 mm
applied load=W
π d4
polar moment of inertia=J =
32
torque=T =F × R
angle of twist=φ
16 T
shear stress=τ=
π d3
TL
shear modulus of rigidity=G=57.3 × N /mm 2
Jφ
PRECAUTIONS:
COMMENTS: