Sei sulla pagina 1di 138

Hydraulic seals

www.hubata-seals.com
Hydraulic Seals

Contents

2 U-rings

3 Materials

5 General notes for installation

6 Installation housing

8 Overview of U-rings

10 Individual description

58 Wipers

59 Materials

61 Installation

62 Overview of Wipers

64 Individual description

102 Hydraulic piston seals (overview)

104 Individual description

114 Hydraulic rod seals (overview)

116 Individual description

128 Guide strips (overview)

130 PTFE seals

The purpose of this catalogue is to present


standard seals dimensions.

For information about stock availabilities, please


contact our sales department.

We are able to supply other dimensions required.

1
U-rings U-rings are among the most important Materials, design and placing sequence
seals used in hydraulics and pneumatics. must be adapted to the varying
Their main function is to seal the cylinder requirements. Whether a U-ring should be
on the piston or piston rod. Whether in an made of pure elastomer or whether it should
unpressurised state or under pressure, they have a support ring, if necessary integrated
prevent the medium escaping from the in a fabric back, depends on the design of
cylinder, thus ensuring the cylinder function. the particular cylinder in question.

The characteristics which distinguish U-rings Different U-ring geometries and materials
are on the one hand the geometry of the should be chosen for heavy-duty
diameter - here a distinction is always made applications with high safety aspects and
between symmetric and asymmetric designs little movement, e.g. in derrick cylinders for
-but also in the shape and final processing of cranes or hydraulic cylinders in barrages,
the sealing lips. than those required for working cylinders of
earth-moving machinery where the focus is
Symmetrical U-rings can be used as on high resistance to wear. Totally different
piston seals as well as piston rod seals. designs and materials to those used in
Asymmetrical U-rings are designed only as hydraulics are on the other hand required
piston or piston rod seals. They are optimally for pneumatic cylinders.
adapted to the applications.
The requirements of the task and the
The function that all U-rings have in possibilities of the U-ring must be carefully
common is diameter energising. The balanced as these have a decisive
oversized lips allow them to be pressed on influence on the selection of the seal and
to the surrounding sealing surface when the resulting operating safety of the system.
built-in, creating linear force around the
circumference: in the seal groove and on
the dynamic side of the seal, the piston rod
and/or the running surface of the cylinder.

The U-ring’s sealing function is guaranteed


even in this unpressurized state. The
hydraulic liquid is held back at the sealing
site which enables a further increase in
pressure. This pressure build-up results in the
hydraulic contact pressure of the medium
against the seal lips overriding the energising
factor. The movement of the dynamic side
completes the sealing mechanism. The
higher the liquid pressure, the more intensive
the contact pressure of the seal on the
surrounding surfaces and the greater the
sealing function.

2
Materials Acrylonitrile-butadiene caoutchouc With textiles that have a woven structure,
— NBR a distinction is made according to the
NBR is the most commonly used material in thickness or weight per surface area, known
all areas of seal technology due to its good as grammage. Another distinguishing
physical and mechanical characteristics characteristic is the basic material these
and its excellent processing abilities. For textiles are made of, e.g. cotton or synthetic
U-rings it is used in hardnesses between 75 fibre. Cotton textile impregnated with NBR is
and 90 Shore A and for O-rings as energising most frequently used for the production of
elements it is generally used in 70 Shore A. standard U-rings. Apart from the standard
materials, there is a whole range of other
This elastomer has the rigidity, hardness and textiles available and almost all elastomers
abrasion resistance necessary for U-rings. for impregnation.

NBR is resistant to most oils and mineral oil Impregnated fabric materials have
based fats used in hydraulics and also to numerous advantages over pure elastomers.
their emulsions with water. The most important are, compressive creep
resistance, extrusion safety, dimensional
NBR materials have only moderate stability and low friction and wear
resistance against weathering and behaviour. They also show little inclination
ozone influences if they are not specially to swelling in hydraulic media and are well-
developed for these applications. However, suited to applications at low temperatures.
the standard resistance is sufficient for most
applications of U-rings and their energising In a two-stage process, the fabric materials
elements made of NBR as with typical are preprocessed into slugs and then
applications in hydraulics, the elastomer vulcanised into seals in a compression
surfaces are moistened with oil or fat. These moulding die with heat application. A multi-
media form a stable surface protective component seal can be produced out of
layer and minimise the intensity of ozone pure elastomer which is moulded on.
influence.
Polyurethane
Generally, the standard NBR90 quality which Polyurethane is one of the group of elastic
is used for most U-rings can be applied at thermoplastic materials which have been
temperatures from -30° C to +100° C. The established in seal technology for many
temperature application limits for NBR 70 years due to their physical characteristics
O-rings as energising elements in U-rings is and efficient processing features.
also from -30° C to +100° C but under special Polyurethan at a hardness range of between
circumstances for both parts a temperature 65 and 98 Shore A is used.
as low as -40° C is still acceptable.
Among the most important material
NBR is processed in moulding tools in various characteristics are its great tensile strength,
compression and vulcanising processes to good wear resistance, good flexibility at
form U-rings or O-rings. a temperature range from -40° C to +100°
C and also good ageing stability against
Fabric materials ozone. The mineral oil based oils and fats
Fabric materials are textiles or non-specific used in hydraulics have a minimal influence
fibrous materials which are impregnated on the physical properties of Polyurethane.
with elastomer materials.

3
Polyurethane TPU92 Polyoxymethylene POM
TPU92, with very few exceptions, in Polyoxymethylene is a thermoplastic
the polyurethane used for U-rings. The material and is distinguished by its
characteristics of this type of material unite particularly high pressure load bearing
the appropriate rigidity, hardness and in ability, rigidity and hardness.
particular, abrasion resistance necessary
for U-rings. The injection moulding process Apart from its application as a pure material,
applied in most cases requires complex POM can be compounded with extenders
machinery and moulding tools and for this to further improve the compressive creep
reason is most appropriate for large-scale resistance and wear resistance which results
production. in a longer service life. Due to POM’s low
water absorption it is not subjected to any
Polytetrafluorethylene (PTFE) volume change which is not always the
PTFE has numerous positive characteristics case with thermoplastics.
which have become indispensable in seal
technology. In particular, we would like to Due to its excellent characteristics under
emphasise the characteristics which are extreme loads, POM is often processed as
essential for its application as U-ring material: a seal accompanying element, e.g. as a
support ring or a piston guiding element with
PTFE is distinguished by exceptional rigidity an angular design.
and very good gliding characteristics. Due
to its extremely low surface energy, it has With a temperature range from -40°C to
a very low coefficient of friction (values of +100° C, POM can be used in almost all
under 0.02 are known) and exceptional non- standard seal application areas.
bonding, non-wettable contact surfaces.
In addition, its extreme hydrophobia must Polyoxymethylene is processed by injection
be mentioned: PTFE is absolutely water- moulding in most cases. The slugs can also
repellent. be processed in a chip removal process.

It is resistant to almost all chemicals and FKM fluorcaoutchouc


remains stable within an extremely wide The FKM elastomer is distinguished by its
temperature range. Apart from this, it is excellent chemical and temperature
immune to attack by oxygen, ozone or resistance (from -20° C to +200° C). It
ultra-violet rays and is therefore completely therefore plays an important part as a U-ring
resistant to weathering. material outside the standard.

PTFE does not contain any extractable Due to the above characteristics it is
media which could drift off and adversely essential to use FKM when extremely high
affect adjacent materials. It is therefore temperatures occur in the surrounding of
physiologically completely harmless the hydraulic cylinder and highly flammable
in contact with foodstuffs and also type D liquids have to be used.
particularly well-suited for applications in the
pharmaceutical and medicinal fields. FKM is generally used in 90 Shore A and
can also be processed in combination with
Combined with different compounds, PTFE metal.
has proved to be excellent material for
U-rings. In particular, PTFE/carbon with a
15% - 25% proportion of carbon improves
the wear resistance of the material which
already has excellent gliding characteristics.
The pressure hardness is also increased by
this additive.

PTFE alone is only slightly elastic. For


this reason the activation of U-rings is
compensated with elastic energising
elements in the form of stainless steel springs.

4
General notes for Although the materials used in our U-rings 4. Dust, dirt, metal chips and any other
are particularly effective and robust, special foreign particles must be carefully
installation
care is still required during installation in order removed.
to avoid mechanical damage especially
to the sealing lip. This would inevitably lead 5. Tips of screws and grooves for guide
to leakage. Furthermore, the U-rings should elements, etc. should be covered using
be checked prior to installation for damage an installation cone, as the seal must not
or ageing that could have occurred during be pushed over gaps, drillings or rough
transportation or storage. To ensure safe surfaces.
installation, the following precautions should
be taken: 6. Cylinders, rods, seals and installation
tools must be greased or oiled before
1. Installation of the seal must take place installation, giving consideration to
with the prestressed side facing the compatibility with the medium.
direction of pressure. Particular care
must be taken with compact U-rings as 7. Materials are made smoother and
the prestressed side is not always easily expand a great deal more easily for
recognisable. installation if they are heated in oil
or hot water at approx. 80°C, giving
2. Lead-in chamfers on the cylinder and consideration to the resistance.
on the piston rod are essential. The
recommended lengths and angles are 8. Any tools used for installation, e.g. cones
given in the installation dimensions for and mandrels for expansion, should be
the various U-rings in this catalogue. made of soft material (e.g. POM) and
not have any sharp edges.
3. Sharp edges must be deburred and radii
and chamfers applied in accordance
with the installation guidelines.

5
Installation housings The function and service life of a hydraulic groove width (5), the lead-in chamfer (6)
or pneumatic cylinder depend to a great and the dimensions of the seal gap on the
extent on the sealing elements used. During side opposite the pressure (7), as well as the
operation, these are subject to various surface finish of the opposed surface (8),
stresses and must therefore be adapted play a major role in ensuring the optimal
to the different requirements in terms of service life of the seals.
material, structure and arrangement.
The key criteria are media compatibility U-rings can generally be installed in cut
and temperature resistance, pressure, housing grooves. However, wider profiles
friction, wear resistance, stroke speed and and particularly small inner diameters require
frequency as well as service life. Seals, an axial opening to the housing. The fit must
grooves and wipers should already be be taken into consideration accordingly,
selected in the construction phase of the which requires special experience. Should
cylinder so that the finish of the metal you require advice, please contact our
surfaces and the design and dimensions of technical department.
the grooves can be carefully manufactured
in accordance with the installation housing Sufficient guiding for the pistons and the
guidelines. piston rods must be ensured, as seals can
never perform guiding tasks.
Rounded corners in the groove base (1)
ensure the correct position of the U-ring Wipers ensure that no foreign particles enter
and rounded flanks of the groove’s edges the medium system of a cylinder that could
(2) minimise the risk of the seal moving into destroy the seals. In order to retain a clean
the metal gap. The suitable surface finish of system and to protect the environment
the groove base (3) and the groove flanks against oil pollution, no hydraulic cylinder
(4), adherence to the tolerances for the should be used without a wiper.

6
Overview of
U-rings Ref. Pressure Temp. Speed Materials Dimensions Page
(bar) (°C) (m/s) metr. inch

Design

HPRS Piston/Rod 160 -30 0,5 NBR90 ■ ■ 10


MA21 seal +100

HPRS Piston/Rod 100 -30 0,5 NBR90 ■ ■ 18


MA22 seal +100

HPS MA23 Piston seal 160 -30 0,5 NBR90 ■ ■ 22


+100

HRS MA24 Rod seal 160 -30 0,5 NBR90 ■ ■ 26


+100

HPS MA31 Piston seal 40 -30 0,5 NBR90 ■ ■ ASK


+100

HRS MA32 Rod seal 40 -30 0,5 NBR90 ■ ■ ASK


+100

HRS MA96 Rod seal 150 ­-30 0,5 NBR90 ■ ASK


+105

HPRS Piston-/Rod 300 -40 0,5 TPU92 ■ ■ 28


MA25 seal +100

HPS MA28 Piston seal 400 -40 0,5 TPU92 ■ 34


+100

HRS MA30 Rod seal 400 - 40 0,5 TPU92 ■ ■ 38


+100

8
Overview of
U-rings Ref. Pressure Temp. Speed Materials Dimensions Page
(bar) (°C) (m/s) metr. inch

Design

HRS MA35 Rod seal 400 -40 0,5 TPU92 ■ ■ 42


+100

HPRS Piston/Rod 400 -40 0,5 TPU92 ■ 45


MA36 seal +100

HRS MA39 Rod seal 400 -40 0,5 TPU92 ■ ■ 48


+100

HPS MA40 Piston seal 400 -­30 0,5 TPU92/POM ■ ■ ASK


+100

HRS MA41 Rod seal 400 -40 0,5 TPU92/POM ■ 52


+100

HPRS Piston-/Rod 400 -40 0,5 TPU92/NBR 70 ■ ASK


MA42 seal +100

HRS MA51 Rod seal 630 -30 0,5 TPU92/NBR/POM ■ ■ ASK


+100

HRS MA43 Rod seal 350 -150 15 PTFE-compounds ■ 54


+250 spring steel
AISI 301

HPS MA44 Piston seal 350 -150 15 PTFE-compounds ■ 56


+250 spring steel
AISI 301

9
HPRS MA21

piston and piston rod seal with symmetrical If the housing is provided with a metallic
sealing lips which are cut at an angle of less fitting on the side opposite the pressure, the
than 45°. service life of the seal is lengthened. Within the
operating parameters given above, depending
Standard material on the pressure, a metallic wedge can be fitted
NBR90 between the cylinder pipe and piston acc. to
Area of application the following table:
Hydraulics and pneumatics
reciprocating movements Pressure (MPa) Radial wedge G (mm)
5 0.2
Function 10 0.15
The HPRS MA21 is a single function piston seal
16 0.1
in the form of a U-ring which can be used as a
piston and piston rod seal due to its symmetrical
sealing lips. Its sealing function is very effective The piston diameter d1 should generally be by
due to the sealing lips being provided with factor 0.65 of the profile smaller than the DN
radial self energising which is activated by the diameter provided.
system pressure.
Please also follow the general installation
Media instructions.
Hydraulic oils acc. DIN 51524/51525,
lubricating oils, mineral oil based Remarks
lubricating fats, non-flammable In addition, we are able to supply other
hydraulic fluids HFA, HFB, HFC acc. dimensions required. For operating conditions
VDMA 24317. other than the standard applications, further
elastomers are available.
Operational application limits
Pressure (MPa/bar): 16/160
Temperature (°C): –30 to + 100
Running speed (m/s): = 0.5

Installation
The HPRS MA21, with an inner diameter of
25 mm and a thinner profile can always be
installed in cut housing. With an inner diameter
of less than 25 mm, we recommend axially
accessible housing. To push the piston body
and seal into the cylinder pipe or over the
piston rod without damaging it, a lead-in
chamfer C acc. to the following table is
required:

Profile width (mm) Lead-in chamfer C (mm)


4 2
5 2.5
7.5 4
10 5
12.5 6.5
15 7.5
20 10
25 10

10
HPRS MA21
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

3 10 6 7 6 14 4 5 8 18 6 7
4 7.5 3 4 6 15 5 6 8 18 8 9
4 10 4 5 6 15 8 9 8 18 9 10
4 10 4.5 5.5 6 15 9 10 8 18 10 11
4 10 5 6 6 16 5 6 8 20 6 7
4 11 8 9 6 16 6 7 8 22 7 8
4 12 4 5 6 17 6 7 8 22 8 9
4 12 5.5 6.5 6 18 8 9 8 22 9 10
5 11 5 6 6 20 8 9 8 25 6 7
5 11 7 8 7 15 4 5 9 15 8 9
5 12 5 6 7 15 5 6 9 17 4 5
5 12 5.5 6.5 7 15 7 8 9 18 5 6
5 12 6 7 7 15 8 9 9 19 6 7
5 13 4 5 8 12 5 6 9 19 7 8
5 13 6 7 8 14 4 5 9.5 30 10 11
5 14 4.5 5.5 8 14 5 6 10 16 4 5
5 14 6 7 8 14 6 7 10 16 5 6
5 15 5 6 8 14 7 8 10 16 6 7
6 10 3 4 8 15 4 5 10 18 4 5
6 12 4 5 8 15 6 7 10 18 5 6
6 12 4.5 5.5 8 15 8 9 10 18 6 7
6 12 5 6 8 15 9 10 10 18 7 8
6 12 5.5 6.5 8 16 4 5 10 18 8 9
6 12 6 7 8 16 6 7 10 18 9 10
6 12 6.5 7.5 8 16 8 9 10 20 5 6
6 12 7 8 8 18 5 6 10 20 6 7

11
HPRS MA21
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

10 20 7 8 14 28 10 11 18 30 6 7
10 20 8 9 14 32 8 9 18 30 7.5 8.5
10 20 9 10 14 32 10 11 18 30 8 9
10 22 6 7 15 20 3 4 18 30 8.5 9.5
10 22 7 8 15 22 4 5 18 30 9 10
10 22 8 9 15 25 5 6 18 30 10 11
10 22 9 10 15 25 6 7 18 32 7 8
10 25 7.5 8.5 15 25 8 9 18 34 8 9
10 25 10 11 15 25 9 10 18 34 12 13
10 26 8 9 15 25 10 11 18 35 10 11
10 26 9.5 10.5 15 27 6 7 18 35 12 13
10 28 10 11 15 27 7 8 18 36 6 7
10 30 10 11 15 28 8 9 18 38 10 11
10 32 10 11 15 28 10 11 18 40 10 11
11 26 8 9 15 28 11 12 18 40 11 12
11 27 8 9 15 30 6 7 19 25 6 7
11.5 21.5 7 8 15 30 7.5 8.5 19 34 10 11
12 18 4 5 15 30 8 9 19 37 10 11
12 18 5 6 15 30 10 11 20 25 3 4
12 18 6 7 15 35 10 11 20 27 6 7
12 18 7 8 16 22 3 4 20 28 4 5
12 20 4 5 16 22 4 5 20 28 5 6
12 20 5 6 16 22 4.5 5.5 20 28 8 9
12 20 8 9 16 22 5 6 20 28 9 10
12 20 9 10 16 22 5.5 6.5 20 29 5 6
12 22 5 6 16 22 6 7 20 29 5.5 6.5
12 22 6 7 16 24 4 5 20 30 5 6
12 22 7 8 16 24 5 6 20 30 6 7
12 22 8 9 16 24 6 7 20 30 8 9
12 22 9 10 16 24 9 10 20 30 9 10
12 24 6 7 16 24 10 11 20 30 10 11
12 24 8 9 16 25 5 6 20 30 11 12
12 24 9 10 16 25 8 9 20 32 6 7
12 24 10 11 16 26 5 6 20 32 7.5 8.5
12 25 8 9 16 26 6 7 20 32 8 9
12 25 9 10 16 26 8 9 20 32 8.5 9.5
12 25 10 11 16 26 9 10 20 33 6 7
12 25 11 12 16 26 10 11 20 35 7.5 8.5
12 26 10 11 16 28 6 7 20 35 10 11
12 28 10 11 16 28 7 8 20 35 12 13
12 32 10 11 16 28 7.5 8.5 20 35 13 14
12 35 12 13 16 32 8 9 20 36 8 9
12.7 19 5 6 16 32 9 10 20 36 10 11
13 23 5 6 16 32 10 11 20 38 9 10
13 25 8 9 16 32 11 12 20 39 10 11
13 25 10 11 16 35 9 10 20 40 5 6
13 30 9 10 16 36 10 11 20 40 10 11
13 30 10 11 17 25 4 5 20 40 11 12
13 35 15 16 17 25 10 11 20 40 12 13
13 36 12 13 17 32 7 8 20 43 12 13
14 20 5 6 17 35 6 7 20 45 12 13
14 20 6 7 17 38 10 11 21 33 6 7
14 22 4 5 18 25 5 6 21 37 12 13
14 22 5 6 18 25 5.5 6.5 22 28 5 6
14 22 6 7 18 26 4 5 22 28 8 9
14 22 7 8 18 26 5 6 22 28 9 10
14 22 8 9 18 26 6.5 7.5 22 30 4 5
14 22 9 10 18 26 7.5 8.5 22 30 5 6
14 22 12 13 18 26 8 9 22 30 6 7
14 24 5 6 18 26 8.5 9.5 22 30 7 8
14 24 6 7 18 26 9.5 10.5 22 30 10 11
14 24 8 9 18 28 5 6 22 32 5 6
14 24 9 10 18 28 6 7 22 32 6 7
14 26 6 7 18 28 8 9 22 32 7 8
14 28 7 8 18 28 10 11 22 32 8 9

12
HPRS MA21
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

22 32 9 10 26 56 14 15 31.5 41.5 6 7
22 32 10 11 27 35 4 5 31.5 44.5 6 7
22 32 11 12 27 36 6 7 32 40 4 5
22 34 6 7 27 38 6 7 32 40 5 6
22 34 10 11 27 42 10 11 32 40 5.5 6.5
22 35 10 11 28 35 5 6 32 40 6 7
22 35 11 12 28 35 5.5 6.5 32 40 7 8
22 37 10 11 28 35 6 7 32 40 8 9
22 38 10 11 28 35.5 5 6 32 40 10 11
22 42 10 11 28 36 4 5 32 42 5 6
22 46 12 13 28 36 5 6 32 42 6 7
23 33 5 6 28 36 6 7 32 42 10 11
23 35 6 7 28 36 6.5 7.5 32 42 11 12
23 35 10 11 28 36 7.5 8.5 32 44 6 7
23 38 10 11 28 38 5 6 32 44 7.5 8.5
23.5 31.5 5 6 28 38 6 7 32 45 10 11
24 32 4 5 28 38 7 8 32 45 11 12
24 32 7 8 28 38 8 9 32 47 10 11
24 32 8 9 28 38 9 10 32 50 10 11
24 34 5 6 28 38 10 11 32 50 12 13
24 34 10 11 28 40 6 7 32 50 13.5 14.5
24 36 6 7 28 40 7.5 8.5 32 52 10 11
24 36 7.5 8.5 28 40 10 11 32 58 13 14
24 40 8 9 28 41 6 7 33 43 5 6
24 40 9 10 28 43 10 11 33 43 6 7
24 40 10 11 28 44 8 9 33 45 6 7
24 40 12 13 28 47 10 11 33 55 12 13
25 32 7 8 28 48 10 11 34 44 5 6
25 33 4 5 28 48 12 13 34 45 7 8
25 33 5 6 29 37 4 5 34 45 8 9
25 33 7 8 30 37 6 7 34 45 9 10
25 35 5 6 30 37 8 9 34 46 8 9
25 35 5.5 6.5 30 38 4 5 34 50 15 16
25 35 6 7 30 38 5 6 34 74 10 11
25 35 7 8 30 38 6 7 35 42 8 9
25 35 8 9 30 38 6.5 7.5 35 43 7 8
25 35 9 10 30 38 7 8 35 45 5 6
25 35 10 11 30 38 12 13 35 45 6 7
25 35 11 12 30 40 5 6 35 45 8 9
25 37 6 7 30 40 5.5 6.5 35 45 9 10
25 37 7 8 30 40 6 7 35 45 10 11
25 38 7 8 30 40 6.5 7.5 35 45 11 12
25 38 9 10 30 40 7 8 35 47 6 7
25 38 10 11 30 40 9 10 35 48 10 11
25 38 11 12 30 40 10 11 35 48 11 12
25 39 7 8 30 40 11 12 35 50 7 8
25 40 7.5 8.5 30 40 11.5 12.5 35 50 7.5 8.5
25 40 8 9 30 42 6 7 35 50 9 10
25 40 10 11 30 42 9 10 35 50 9.5 10.5
25 40 11 12 30 42 10 11 35 50 10 11
25 42 8 9 30 42 11 12 35 50 11 12
25 45 10 11 30 43 6.5 7.5 35 52 10 11
25 45 12 13 30 45 7.5 8.5 35 52 12 13
25 47 12 13 30 45 9 10 35 55 10 11
25 50 10 11 30 45 10 11 35 55 11 12
25 50 12 13 30 45 11 12 35 55 12 13
26 34 4 5 30 47 10 11 35 55 13 14
26 35 5 6 30 50 10 11 35 60 12 13
26 36 5 6 30 50 11 12 35.5 45 6 7
26 36 6 7 30 50 12 13 35.5 45.5 6 7
26 36 7 8 30 50 13 14 36 45 10 11
26 38 6 7 30 52 11 12 36 46 5 6
26 42 8 9 30 55 12 13 36 46 7 8
26 46 10 11 30 60 15 16 36 46 8 9
26 47 12 13 31 38 7 8 36 46 10 11

13
HPRS MA21
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

36 48 6 7 40 70 16 17 48 68 12 13
36 48 7.5 8.5 40 76 12 13 50 57 10 11
36 50 8 9 41 56 8.5 9.5 50 60 5 6
36 51 7.1 8.1 41 56 10 11 50 60 6 7
36 51 7.5 8.5 42 50 5 6 50 60 7 8
36 51 10 11 42 50 6 7 50 60 8 9
36 52 10 11 42 50 8 9 50 60 10 11
36 55 10 11 42 50 9 10 50 60 11 12
36 70 10 11 42 50 10 11 50 60 12 13
38 45 5 6 42 52 5 6 50 62 6 7
38 45 5.5 6.5 42 52 9 10 50 62 9 10
38 45 6 7 42 52 10 11 50 62 10 11
38 46 6.5 7.5 42 54 6 7 50 63 6 7
38 46 7.5 8.5 42 55 8 9 50 63 7 8
38 46 12 13 42 57 10 11 50 63 8 9
38 48 5 6 42 62 12 13 50 63 9 10
38 50 6 7 42 62 15 16 50 63 10 11
38 50 9 10 42 62 18 19 50 65 7.5 8.5
38 50 10 11 43 50 12 13 50 65 9 10
38 50 12 13 43 55 6 7 50 65 10 11
38 52.5 9 10 43 63 10 11 50 65 11 12
38 52.5 9.5 10.5 44 54 4 5 50 65 12 13
38 53 10 11 44 56 6 7 50 68 12 13
38 55 10 11 44 56 7.5 8.5 50 70 8 9
38 55 11 12 44 57 9 10 50 70 10 11
38 58 10 11 44 64 10 11 50 70 11 12
38 58 11 12 45 53 12 13 50 70 12 13
38 58 12 13 45 55 5 6 50 70 18 19
38 60 12 13 45 55 6 7 50 70 19 20
38 74 6 7 45 55 6.5 7.5 50 72 12 13
39.7 51 8 9 45 55 7.5 8.5 50 73 13 14
40 48 5 6 45 55 10 11 50 74 12 13
40 48 8 9 45 55 11 12 50 75 12 13
40 48 12 13 45 56 7 8 50 75 15 16
40 50 5 6 45 57 6 7 50 76 12 13
40 50 6 7 45 58 10 11 50 90 18 9
40 50 6.5 7.5 45 58 12 13 50.9 70 13 14
40 50 7 8 45 60 7.5 8.5 51 60.5 9 10
40 50 7.5 8.5 45 60 9 10 51 63 6 7
40 50 9 10 45 60 10 11 51 64 9 10
40 50 10 11 45 60 11 12 52 62 12 13
40 50 11 12 45 63 9 10 52 62 13 14
40 52 6 7 45 63 10 11 52 64 6 7
40 52 7 8 45 63 11 12 52 64 7.5 8.5
40 52 7.5 8.5 45 63 12 13 52 68 8 9
40 52 10 11 45 65 10 11 52 72 12 13
40 52 12 13 45 65 11 12 52 75 12 13
40 55 7.5 8.5 45 65 12 13 52 80 15 16
40 55 9.5 10.5 45 65 13 14 53 63 5 6
40 55 10 11 45 75 15 16 53 63 6 7
40 55 11 12 46 54 6.5 7.5 53 63 6.5 7.5
40 56 8 9 46 56 5 6 53 63 7.5 8.5
40 56 10 11 46 58 6 7 53 65 6 7
40 56 11 12 46 70 12 13 54 66 6 7
40 58 10 11 47 65 12 13 54 72 10 11
40 60 10 11 47 66.7 10 11 55 63 12 13
40 60 11 12 48 58 10 11 55 65 5 6
40 60 12 13 48 58 11 12 55 65 6 7
40 60 13 14 48 60 6 7 55 65 10 11
40 60 14 15 48 60 7.5 8.5 55 65 11 12
40 60 18 19 48 63 9 10 55 65 12 13
40 64 12 13 48 63 10 11 55 65 13 14
40 65 12 13 48 63 12 13 55 67 6 7
40 65 13 14 48 65 10 11 55 68 7.5 8.5
40 65 15 16 48 68 10 11 55 70 7.5 8.5

14
HPRS MA21
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

55 70 9 10 63 75 11 12 70 90 18 19
55 70 10 11 63 75 12 13 70 90 19 20
55 70 12 13 63 78 10 11 70 95 12 13
55 70 13 14 63 80 12.5 13.5 70 95 13 14
55 75 10 11 63 83 12 13 70 95 15 16
55 75 12 13 63 83 13 14 70 100 10 11
55 75 13 14 63 83 15 16 70 100 15 16
55 76 10 11 63 83 16 17 70 105 10 11
55 80 10 11 63.5 73.5 9 10 71 80 6 7
55 80 12 13 64 76 9 10 72 80 10 11
55 80 13 14 64 80 8 9 72 80 12 13
55 80 15 16 65 73 12 13 72 82 5 6
55 85 10 11 65 75 5 6 72 90 10 11
55 85 15 16 65 75 6 7 72 90 11 12
56 66 5 6 65 75 10 11 72 90 12 13
56 66 6 7 65 75 12 13 73 93 11 12
56 70 12 13 65 75 13 14 75 83 12 13
56 71 10 11 65 80 7.5 8.5 75 85 5 6
56 76 12 13 65 80 9 10 75 85 6 7
56 80 15 16 65 80 11 12 75 85 10 11
58 70 6 7 65 80 12 13 75 85 12 13
58 77 9.5 10.5 65 80 13 14 75 85 13 14
58 78 12 13 65 82 12 13 75 90 7.5 8.5
59 80 14 15 65 85 10 11 75 90 8.5 9.5
60 68 8 9 65 85 11 12 75 90 9 10
60 68 12.5 13.5 65 85 12 13 75 90 10 11
60 70 5 6 65 86 12 13 75 90 10.5 11.5
60 70 6 7 65 90 8 9 75 90 13 14
60 70 7 8 65 90 12 13 75 95 10 11
60 70 8 9 65 90 13 14 75 95 12 13
60 70 9 10 65 90 15 16 75 95 13 14
60 70 10 11 65 95 12 13 75 95 15 16
60 70 12 13 65 95 13 14 75 100 15 16
60 70 13 14 65 100 12 13 75 105 15 16
60 71 7 8 66 76 10 11 78 88 5 6
60 72 11 12 66 77 6 7 78 93 10.5 11.5
60 75 7.5 8.5 66 80 10 11 78 93 11.5 12.5
60 75 8 9 66 80 11 12 78 104 12.5 13.5
60 75 9 10 67 77 6 7 80 90 5 6
60 75 10 11 67 77 12 13 80 90 6 7
60 75 11 12 67 77 13 14 80 90 10 11
60 75 12 13 67 80 12 13 80 90 11 12
60 75 13 14 68 76 6.5 7.5 80 90 12 13
60 76 8 9 68 80 12 13 80 90 13 14
60 80 10 11 68 92 15 16 80 92 10 11
60 80 11 12 70 80 5 6 80 95 7.5 8.5
60 80 12 13 70 80 6 7 80 95 8 9
60 80 13 14 70 80 7 8 80 95 9 10
60 80 18 19 70 80 8 9 80 95 12 13
60 80 19 20 70 80 9 10 80 95 13 14
60 85 12 13 70 80 11 12 80 100 10 11
60 85 12.5 13.5 70 80 12 13 80 100 11 12
60 85 13.5 14.5 70 80 13 14 80 100 12 13
60 85 15 16 70 81 15 16 80 100 13 14
60 86.7 15 16 70 82 12 13 80 100 15 16
60 90 15 16 70 85 7.5 8.5 80 100 18 19
60 90 16 17 70 85 8 9 80 101.6
12 13
60 95 13 14 70 85 9 10 80 105 12 13
61 69 6.5 7.5 70 85 10.5 11.5 80 105 15 16
61 80 12 13 70 85 12 13 80 110 15 16
62 72 12.5 13.5 70 85 13 14 80 110 18 19
63 72 6 7 70 90 10 11 80 115 12.5 13.5
63 73 5 6 70 90 12 13 82 92 10 11
63 73 6 7 70 90 13 14 82 92 11 12
63 75 10 11 70 90 15 16 82 104 12.5 13.5

15
HPRS MA21
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

82 108 12 13 95 115 10 11 113 125 9.5 10.5


83 103 14 15 95 115 12 13 113 125 10.5 11.5
84 103 14 15 95 115 13 14 114 124 10 11
85 95 7.5 8.5 95 115 15 16 115 123 12 13
85 95 8.5 9.5 95 115 18 19 115 125 8 9
85 95 9 10 95 115 19 20 115 125 15 16
85 95 12 13 95 120 12 13 115 125 16 17
85 95 13 14 95 120 13 14 115 126 15 16
85 100 7.5 8.5 95 120 15 16 115 129 13 14
85 100 9 10 95 125 13 14 115 130 7.5 8.5
85 100 12 13 95 125 15 16 115 130 15 16
85 100 13 14 96 104 11.5 12.5 115 135 12 13
85 105 10 11 96 105 11 12 115 135 15 16
85 105 12 13 98 108 10 11 115 135 16 17
85 105 13 14 98 112 8.5 9.5 115 140 15 16
85 105 15 16 100 110 5 6 115 140 18 19
85 105 18 19 100 112 9 10 115 145 12 13
85 110 12 13 100 114 10 11 115 145 18 19
85 110 15 16 100 115 7.5 8.5 120 130 14 15
85 115 15 16 100 115 9 10 120 130 15 16
85 115 16 17 100 115 12 13 120 135 7.5 8.5
86 105 16 17 100 115 13 14 120 135 10 11
86 106 10 11 100 115 14 15 120 135 15 16
88 96 6.5 7.5 100 117.5 12 13 120 135 16 17
88 108 12 13 100 120 10 11 120 140 10 11
89 100 12 13 100 120 12 13 120 140 12 13
90 98 12 13 100 120 13 14 120 140 14 15
90 100 5 6 100 120 15 16 120 140 15 16
90 100 8 9 100 125 12 13 120 140 16 17
90 100 9 10 100 125 13 14 120 145 18 19
90 100 12 13 100 125 15 16 120 150 15 16
90 100 13 14 100 125 16 17 120 150 18 19
90 100 15 16 100 125 18 19 125 140 7.5 8.5
90 105 7.5 8.5 100 130 15 16 125 140 9 10
90 105 9 10 100 130 18 19 125 140 11 12
90 105 12 13 105 120 7.5 8.5 125 140 12 13
90 105 13 14 105 120 9 10 125 140 13 14
90 110 10 11 105 120 15 16 125 140 15 16
90 110 12 13 105 125 12 13 125 140 16 17
90 110 13 14 105 125 13 14 125 145 12 13
90 110 15 16 105 125 15 16 125 145 15 16
90 110 18 19 105 125 16 17 125 145 16 17
90 110 19 20 105 130 12 13 125 145 18 19
90 112 12 13 105 130 18 19 125 145 19 20
90 115 12 13 105 135 18 19 125 147 12 13
90 115 12.5 13.5 106 120 8.5 9.5 125 150 18 19
90 115 15 16 106 130 18 19 125 154 20 21
90 120 15 16 107 115 6.5 7.5 125 155 15 16
90 120 18 19 107 127.4 16 17 125 155 16 17
91 99 6.5 7.5 108 127 9.5 10.5 125 155 18 19
92.4 102 9.5 10.5 110 125 7.5 8.5 127 142 12 13
93 123 15 16 110 125 12 13 127 151 16 17
94 124 15 16 110 125 13 14 128 158 18 19
95 103 12 13 110 125 15 16 130 140 15 16
95 105 5 6 110 130 12 13 130 145 15 16
95 105 11 12 110 130 15 16 130 150 10 11
95 105 12 13 110 130 16 17 130 150 12 13
95 110 7.5 8.5 110 130 18 19 130 150 14 15
95 110 9 10 110 130 19 20 130 150 15 16
95 110 12 13 110 135 12 13 130 150 16 17
95 110 13 14 110 135 18 19 130 155 18 19
95 110 15 16 110 140 15 16 130 160 13 14
95 110 16 17 110 140 18 19 130 160 15 16
95 112 11 12 111.1 130.1 15 16 130 160 18 19
95 112 12 13 112 125 9 10 132 144 12 13

16
HPRS MA21
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

133 149 11 12 160 195 17 18 255 275 20 21


135 143 12 13 160 200 20 21 255 280 20 21
135 150 9 10 165 180 9 10 255 285 20 21
135 150 15 16 168 180 14 15 255 290 20 21
135 160 18 19 170 200 15 16 260 300 20 21
135 165 12 13 170 200 20 21 270 300 20 21
135 165 15 16 170 200 22 23 270 300 22 23
135 165 18 19 170 210 20 21 280 300 14 15
136 150 8.5 9.5 170 210 22 23 280 310 15 16
140 154 10 11 175 205 18 19 280 320 20 21
140 160 8 9 180 210 22 23 300 325 20 21
140 160 15 16 180 220 22 23 300 330 20 21
140 165 18 19 185 195 12 13 300 330 22 23
140 170 15 16 185 200 9 10 300 340 20 21
140 170 18 19 190 210 15 16 310 350 20 21
140 175 15 16 190 220 15 16 320 350 15 16
145 160 8 9 190 220 22 23 320 350 22 23
145 165 12 13 190 220 25 26 320 360 20 21
145 165 18 19 195 225 15 16 335 367 24 25
145 170 18 19 200 230 15 16 340 380 20 21
145 175 15 16 200 230 22 23 342 355 22 23
145 175 18 19 200 240 20 21 350 400 25 26
150 165 16 17 210 250 20 21 360 420 30 31
150 170 15 16 215 230 7.5 8.5 375 395 12 13
150 170 18 19 220 250 20 21 375 400 22 23
150 180 15 16 220 260 20 21 400 450 25 26
150 180 18 19 225 250 18 19 420 440 20 21
155 163 12 13 230 260 22 23 420 450 20 21
160 168 12 13 230 270 20 21 450 500 25 26
160 170 15 16 240 260 16 17 470 490 20 21
160 175 9 10 240 270 18 19 470 500 20 21
160 180 15 16 240 280 20 21 550 600 25 26
160 190 15 16 250 275 12 13
160 190 22 23 250 290 20 21

17
HPRS MA22

piston and piston rod seal with symmetrical


sealing lips which are cut straight. Profile width (mm) Lead-in chamfer C (mm)
4 2
Standard material 5 2.5
NBR90
7.5 4
10 5
Area of application
12.5 6.5
Hydraulics and pneumatics
15 7.5
reciprocating movements
20 10

Function 25 10

The HPRS MA22 is a single function piston seal


in the form of a U-ring which can be used as a If the housing is provided with a metallic
piston and piston rod seal due to its symmetrical fitting on the side opposite the pressure, the
sealing lips. Its sealing function is very effective service life of the seal is lengthened. Within the
due to the sealing lips being provided with operating parameters given above, depending
radial self energising which is activated by on the pressure, a metallic wedge can be fitted
the system pressure. For new design we between the cylinder pipe and piston acc. to
recommend HPS MA23 or HRS MA24. the following table:

Media Pressure (MPa) Radial wedge G (mm)


Hydraulic oils acc. DIN 51524/51525, 5 0.2
lubricating oils, mineral oil based 10 0.15
lubricating fats, non-flammable
hydraulic fluids HFA, HFB, HFC acc. The piston diameter d1 should generally be by
VDMA 24317. factor 0.65 of the profile smaller than the DN
diameter provided.
Operational application limits Please also follow the general installation
Pressure (MPa/bar): 10/100 instructions.
Temperature (°C): –30 to + 100
Running speed (m/s): = 0.5 Remarks
In addition, we are able to supply other
Installation dimensions required. For operating conditions
The HPRS MA22, with an inner diameter of other than the standard applications, further
25 mm and a thinner profile can always be elastomers are available.
installed in cut housing. With an inner diameter
of less than 25 mm, we recommend axially
accessible housing. To push the piston body
and seal into the cylinder pipe or over the
piston rod without damaging it, a lead-in
chamfer C acc. to the following table is
required:

18
HPRS MA22
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

3 7 5 6 8 22 8 9 12 28 10 11
3 8.5 4 5 8 25 6 7 12 30 9 10
3 10 5 6 9 17 6 7 12 32 10 11
4 10 4 5 10 14 2.5 3.5 12 34 10 11
4 10 5 6 10 15 5 6 12 35 12 13
4 11 8 9 10 16 4 5 12 40 10 11
4 12 4 5 10 16 5 6 12.6 17.5 6.5 7.5
5 11 5 6 10 18 5 6 13 20 3 4
5 12 5 6 10 18 6 7 13 24 6 7
5 14 4.5 5.5 10 20 8 9 13 30 10 11
5 15 5 6 10 22 6 7 14 20 4 5
6 10 4 5 10 22 8 9 14 22 4 5
6 12 4 5 10 22 9 10 14 22 6 7
6 12 6 7 10 25 6 7 14 22 8 9
6 12 8 9 10 25 8 9 14 24 6 7
6 15 5 6 10 25 10 11 14 28 7 8
6 15 6 7 10 26 8 9 14 28 10 11
6 16 5 6 10 28 8 9 14 30 8 9
6 16 6 7 10 30 10 11 14 32 10 11
6 17 6 7 10 32 6 7 15 20 3 4
6 18 8 9 10 32 10 11 15 22 4 5
6 20 8 9 11 17 3.2 4.2 15 22 5.5 6.5
6 22 8 9 12 18 4 5 15 24 4.5 5.5
7 14 3.5 4.5 12 18 5 6 15 24 7 8
7 15 5 6 12 20 5.5 6.5 15 25 5 6
8 12 4 5 12 20 8 9 15 25 6 7
8 13 5 6 12 22 5 6 15 28 10 11
8 14 4 5 12 22 6 7 15 30 8 9
8 14 6 7 12 22 7 8 15 30 10 11
8 15 6 7 12 24 6 7 15 32 8.5 9.5
8 16 4 5 12 24 10 11 15 35 10 11
8 16 6 7 12 25 8 9 16 22 6 7
8 16 8 9 12 26 7 8 16 25 5 6
8 17 6 7 12 26 8 9 16 26 5 6
8 18 8 9 12 26 10 11 16 26 6 7

19
HPRS MA22
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

16 27 5.5 6.5 24 40 8 9 35 60 12 13
16 28 6 7 24 40 10 11 36 46 6 7
16 28 9 10 24 44 10 11 36 48 6 7
16 29 6 7 24 50 12 13 36 50 7 8
16 30 6 7 25 32 4 5 36 51 10 11
16 32 8 9 25 33 7 8 36 55 10 11
16 32 10 11 25 35 5 6 38 50 6 7
16 32 11 12 25 35 6 7 38 53 10 11
16 36 10 11 25 35 8 9 38 56 9 10
16 40 12 13 25 36 5 6 38 58 10 11
17 35 10 11 25 38 7 8 38 58 12 13
17 38 10 11 25 38 8 9 38 60 12 13
18 24 4 5 25 40 6 7 39 45 4 5
18 24 5 6 25 40 10 11 40 46 4 5
18 25 4 5 25 42 8 9 40 48 8 9
18 25 5 6 25 42 8.5 9.5 40 48 11 12
18 26 4 5 25 45 10 11 40 50 5 6
18 28 6 7 25 45 12 13 40 52 8 9
18 28 8 9 25 50 10 11 40 55 10 11
18 30 6 7 25 50 12 13 40 56 8 9
18 30 10 11 25 52 12 13 40 56 10 11
18 32 7 8 26 38 6 7 40 58 10 11
18 34 8 9 26 42 8 9 40 60 10 11
18 35 8.5 9.5 26 46 10 11 40 60 12 13
18 35 12 13 27 36 6 7 40 62 12 13
18 36 6 7 27 42 10 11 40 64 12 13
18 38 10 11 28 38 5 6 40 65 12 13
18 40 10 11 28 38 7 8 40 70 15 16
19 26 5 6 28 43 10 11 41 56 10 11
19 34 8 9 28 44 8 9 42 50 6 7
19 34 10 11 28 45 10 11 42 52 6 7
20 28 4 5 28 46 10 11 42 55 6.5 7.5
20 28 6 7 28 48 10 11 42 57 10 11
20 28 8 9 28 48 12 13 42 62 10 11
20 30 6 7 29 45 8 9 42 62 12 13
20 30 8 9 30 37 8 9 43 63 10 11
20 30 10 11 30 38 7 8 44 55 6 7
20 32 7.5 8.5 30 40 5 6 45 52 8 9
20 33 6 7 30 40 9 10 45 57 6 7
20 35 10 11 30 41 8 9 45 58 6.5 7.5
20 36 8 9 30 42 10 11 45 58 10 11
20 38 8.5 9.5 30 45 10 11 45 60 7 8
20 38 10 11 30 48 9 10 45 60 10 11
20 40 10 11 30 50 10 11 45 63 10 11
20 43 12 13 30 50 12 13 45 65 10 11
22 28 5 6 30 54 12 13 45 65 12 13
22 28 6 7 30 55 12 13 45 69 12 13
22 30 6 7 30 55 15 16 45 70 12 13
22 30 7.5 8.5 30 60 15 16 46 70 12 13
22 32 5 6 32 40 4 5 48 60 6 7
22 32 6 7 32 40 7 8 48 63 10 11
22 34 6 7 32 42 10 11 48 65 10 11
22 34 10 11 32 44 6 7 48 68 10 11
22 35 7 8 32 45 6.5 7.5 48 68 12 13
22 36 8 9 32 45 10 11 48 70 10 11
22 37 10 11 32 47 10 11 48 72 12 13
22 38 8 9 32 48 8 9 49 65 8 9
22 38 10 11 32 50 9 10 50 56 8 9
22 40 10 11 32 50 10 11 50 60 10 11
22 42 10 11 32 52 10 11 50 62 6 7
22 46 12 13 33 43 6 7 50 63 6.5 7.5
23 32 5 6 35 15 5 6 50 65 10 11
23 35 10 11 35 45 6 7 50 70 7.5 8.5
23 38 10 11 35 50 8 9 50 70 10 11
23 43 10 11 35 50 10 11 50 70 12 13
24 30 5 6 35 51 8 9 50 72 12 13
24 31 5 6 35 52 12 13 50 74 12 13
24 32 4 5 35 55 10 11 50 75 12 13
24 34 5 6 35 55 12 13 50 80 15 16
24 37 6 7 35 56 10 11 51 63 6 7

20
HPRS MA22
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

52 62 6 7 80 115 15 16 160 200 20 21


53 65 10 11 82 100 9 10 165 195 15 16
55 65 5 6 85 100 7.5 8.5 170 200 15 16
55 68 6.5 7.5 85 105 10 11 170 200 22 23
55 70 7.5 8.5 85 105 12 13 170 210 20 21
55 75 10 11 85 110 12 13 175 205 15 16
55 80 12 13 85 110 15 16 180 200 10 11
55 85 10 11 85 115 15 16 180 204 12 13
55 85 15 16 86 98 12 13 180 210 15 16
56 75 7 8 88 100 6 7 180 210 22 23
56 76 10 11 90 105 7.5 8.5 180 220 20 21
58 70 6 7 90 110 10 11 185 215 15 16
58 78 12 13 90 115 12 13 190 220 15 16
58 80 10 11 90 115 15 16 190 230 20 21
60 68 8 9 90 120 15 16 195 225 15 16
60 70 7.5 8.5 92 116 12 13 200 220 18 19
60 74 7 8 95 110 7.5 8.5 200 230 15 16
60 75 12 13 95 115 7.5 8.5 200 240 20 21
60 80 10 11 95 115 10 11 205 230 15 16
60 80 12 13 95 120 12 13 210 240 20 21
60 84 12 13 95 125 15 16 210 250 20 21
60 85 12 13 97 105 8 9 220 250 15 16
60 85 15 16 100 110 5 6 220 260 20 21
60 90 15 16 100 120 10 11 225 255 15 16
61 73 6 7 100 120 18 19 230 255 15 16
62 78 8 9 100 125 12 13 230 270 20 21
62 82 10 11 100 130 15 16 235 275 20 21
62 88 12 13 100 140 20 21 240 272 16 17
63 73 12 13 105 120 8 9 240 280 20 21
63 93 15 16 105 125 10 11 250 280 25 26
64 80 8 9 105 130 12 13 250 290 20 21
65 80 7.5 8.5 106 118 12 13 260 285 12 13
65 85 10 11 110 125 7.5 8.5 260 300 20 21
65 85 12 13 110 130 10 11 270 310 20 21
65 90 12 13 110 135 12 13 280 310 15 16
65 95 12 13 110 140 15 16 280 320 20 21
66 76 10 11 110 150 20 21 280 330 25 26
68 78 10 11 115 140 12 13 290 330 20 21
68 80 12 13 115 145 12 13 300 320 15 16
70 82 12 13 120 140 10 11 300 330 16 17
70 85 7.5 8.5 120 150 15 16 300 336 18 19
70 90 10 11 125 145 10 11 300 340 20 21
70 90 12 13 125 150 18 19 305 355 25 26
70 95 12 13 125 155 15 16 310 350 20 21
70 100 15 16 130 150 10 11 330 366 18 19
72 80 10 11 130 160 15 16 330 370 20 21
72 84 6 7 135 150 10 11 340 380 20 21
74 80 8 9 135 160 12 13 350 400 25 26
74 90 8 9 135 160 18 19 360 400 20 21
75 90 7.5 8.5 135 165 15 16 380 420 20 21
75 95 10 11 140 160 10 11 390 415 15 16
75 100 12 13 140 165 18 19 400 430 15 16
75 100 15 16 140 170 15 16 400 440 20 21
75 105 15 16 140 170 20 21 400 450 25 26
78 86 8 9 140 175 20 21 410 450 20 21
78 102 12 13 145 170 15 16 420 450 15 16
80 93 8 9 145 175 15 16 440 480 25 26
80 94 6 7 150 170 10 11 450 500 25 26
80 95 7.5 8.5 150 180 15 16 460 500 20 21
80 100 10 11 155 185 15 16 510 550 20 21
80 105 12 13 160 180 14 15 510 580 20 21
80 110 15 16 160 185 15 16 550 600 25 26
80 110 18 19 160 190 15 16 580 630 25 26

21
HPS MA23 25 10

piston seal with asymmetrical sealing lips which


are cut at an angle of less than 45°.
If the housing is provided with a metallic
Standard material fitting on the side opposite the pressure, the
NBR90 service life of the seal is lengthened. Within the
operating parameters given above, depending
Area of application on the pressure, a metallic wedge can be fitted
Hydraulics and pneumatics between the cylinder pipe and piston acc. to
reciprocating movements the following table:

Function Pressure (MPa) Radial wedge G (mm)


he HPS MA23 is a single function piston seal in 8 0.1
the form of a U-ring. Due to its asymmetrical
sealing lips with a slightly indented outer lip The piston diameter d1 should generally be by
edge, the energising is guided outwards to factor 0.65 of the profile smaller than the DN
strengthen its sealing function also at low diameter provided.
pressure.
Please also follow the general installation
Media instructions.
Hydraulic oils acc. DIN 51524/51525,
lubricating oils, mineral oil based Remarks
lubricating fats, non-flammable In addition, we are able to supply other
hydraulic fluids HFA, HFB, HFC acc. dimensions required. For operating conditions
VDMA 24317. other than the standard applications, further
elastomers are available.
Operational application limits
Pressure (MPa/bar): 16/160
Temperature (°C): –30 to + 100
Running speed (m/s): = 0.5

Installation
The HPS MA23 can be installed in cut housing.
To push the piston body and seal into the
cylinder pipe without damaging it, a lead-
in chamfer C acc. to the following table is
required:

Profile width (mm) Lead-in chamfer C (mm)


4 2
5 2.5
7.5 4
10 5
12.5 6.5
15 7.5
20 10

22
HPS MA23
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

7.5 4.5 3 4 26 18 7 8 40 27 8 9
9 4 3.5 4.5 28 18 8 9 40 27 10 11
12 6 4 5 28 16 9 10 40 28 10 11
12 8 5 6 28 20 5.5 6.5 40 30 6 7
13 7 4 5 30 16 10 11 40 30 7 8
14 6 8 9 30 18 8 9 40 30 8 9
14 8 4.5 5.5 30 20 5 6 40 30 10 11
15 8 5.5 6.5 30 20 7 8 40 32 5.5 6.5
15 9 8 9 30 20 8 9 40 32 8 9
16 6 8 9 30 22 5 6 40 33 8 9
16 6 10 11 30 22 5.5 6.5 41 28 10 11
16 8 5.5 6.5 30 22 6 7 42 32 10 11
16 8 6 7 31 18 10 11 43 25 9 10
16 10 4 5 32 22 5 6 43 30 10 11
16 10 6 7 32 22 7 8 43 38 3.8 4.8
18 10 5 6 32 24 5.5 6.5 45 28.5 12 13
18 10 5.5 6.5 32 26 5.5 6.5 45 30 9 10
20 10 6 7 33 20 10 11 45 30 10 11
20 10 7 8 33 25 5 6 45 32 8 9
20 10 8 9 35 20 10 11 45 32 10 11
20 12 5.5 6.5 35 22 10 11 45 35 6 7
20 12 6.8 7.8 35 25 6.5 7.5 45 35 7 8
20 14 4.2 5.2 35 25 7 8 45 37 7 8
20 14 10 11 35 25 8 9 46 36 7 8
22 13 7 8 35 27 5 6 48 38 8 9
22 14 5.5 6.5 36 24 6 7 50 30 8 9
24 16 5.5 6.5 36 26 7 8 50 30 12 13
25 10 10 11 36 28 7 8 50 34 10 11
25 15 5 6 37 21 12 13 50 34 12 13
25 15 8 9 38 28 7 8 50 35 9 10
25 17 5.5 6.5 39 26 9.5 10.5 50 35 10 11
25 17 6 7 39 32 5 6 50 35 12 13
25 18 5 6 40 20 12 13 50 36 10 11
26 18 5.5 6.5 40 25 9 10 50 40 5 6
26 18 5 6 40 25 10 11 50 40 6 7

23
HPS MA23
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

50 40 7 8 70 62 7.7 8.7 100 85 12 13


50 40 8 9 70 62 8 9 100 86 12 13
50 40 10 11 71 51 12 13 100 88 8.5 9.5
50 42 8 9 71 55 10 11 100 88 10 11
52 42 5 6 71 55 12 13 100 90 7.2 8.2
52 36 12 13 71 56 9 10 100 90 8.5 9.5
52 42 7 8 71 56 10 11 100 90 10.5 11.5
55 40 10 11 71 60 7 8 100 90 16.5 17.5
55 45 6 7 71 61 6 7 105 85 15 16
55 45 7 8 71 61 8 8 105 90 9 10
55 45 8 9 72 58 12 13 105 90 12 13
55 45 10 11 74 62 8.5 9.5 105 93 8.5 9.5
56 40 10 11 75 55 12 13 110 90 12 13
56 40 12 13 75 59 12 13 110 90 15 16
56 41 9 10 75 60 10 11 110 95 9 10
56 41 10 11 75 63 8.5 9.5 110 95 10 11
56 45 7 8 75 65 5 6 110 95 12 13
56 46 6 7 75 65 6 7 110 98 8.5 9.5
56 46 7 8 75 65 7.5 8.5 110 100 5.5 6.5
56 46 8 9 75 65 8 9 111 95 10 11
60 40 12 13 75 65 10 11 112 92 12 13
60 40 13.5 14.5 75 65 13.5 14.5 112 92 15 16
60 44 12 13 76 60 12 13 112 97 9 10
60 45 10 11 80 60 10 11 112 97 10 11
60 50 5 6 80 60 14 15 112 98 8.5 9.5
60 50 6 7 80 63 14 15 115 95 14 15
60 50 7 8 80 63 16 17 115 100 9 10
60 50 8 9 80 64 8 9 115 100 10.5 11.5
60 50 10 11 80 65 9 10 120 100 12 13
60 52 8 9 80 65 10 11 120 100 13.5 14.5
61 45 12 13 80 65 12 13 120 100 15 16
61 56 8 9 80 68 8.5 9.5 120 103 15.5 16.5
62 46 12 13 80 70 6 7 120 105 9 10
62 47 10 11 80 70 7.2 8.2 120 105 10 11
62 52 7 8 80 70 8 9 120 106 8.5 9.5
63 45 10 11 80 70 12 13 125 95 18 19
63 45 12 13 80 71 6 7 125 105 12 13
63 47 12 13 80 72 12 13 125 105 15 16
63 48 10 11 83 71.9 7.5 8.5 125 105 16 17
63 48 12 13 85 65 12 13 125 110 9 10
63 53 6 7 85 65 13.5 14.5 125 110 10 11
63 53 7 8 85 70 9 10 125 112 9 10
63 53 8 9 85 70 10 11 125 115 7.2 8.2
63 53 12 13 85 73 8.5 9.5 125 115 15 16
65 45 12 13 85 75 6 7 130 110 12 13
65 49 12 13 85 75 12 13 130 110 15 16
65 50 7.93 8.93 90 68 16.5 17.5 130 110 16 17
65 50 9 10 90 70 12 13 130 115 9 10
65 50 10 11 90 75 9 10 130 115 10 11
65 53 10 11 90 75 10 11 135 115 14 15
65 55 6 7 90 75 12 13 136 116 14 15
65 55 7 8 90 78 8.5 9.5 140 110 25 26
65 55 8 9 90 80 5 6 140 115 18 19
65 55 10 11 90 80 6 7 140 120 10 11
65 55 13.5 14.5 90 80 8 9 140 120 12 13
66 50 12 13 90 80 13 14 140 120 14 15
67 57 7 8 95 75 12 13 140 120 16 17
68 52 8 9 95 75 13.5 14.5 140 125 10 11
68 58 7 8 95 75 15 16 140 127.3 9.52 10.52
70 50 14 15 95 80 9 10 145 130 10 11
70 54 12 13 95 80 10 11 147 120 15 16
70 55 9.5 10.5 95 85 6.8 7.8 147 120 18 19
70 55 10 11 95 85 7.2 8.2 150 120 18 19
70 55 12 13 95 85 8.5 9.5 150 125 13.5 14.5
70 58 8.5 9.5 95 85 13.5 14.5 150 125 19 20
70 60 6 7 100 80 10 11 150 125 20 21
70 60 7.2 8.2 100 80 15 16 150 130 12 13
70 60 8 9 100 80 13.5 14.5 150 130 15 16
70 60 12 13 100 85 9 10 150 130 16 17
70 60 13.5 14.5 100 85 10 11 150 135 8 9

24
HPS MA23
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

150 135 9 10 190 170 15 16 250 225 16 17


150 135 10 11 190 170 16 17 250 225 19 20
150 136 8.5 9.5 190 175 10 11 250 225 20 21
150 140 7.2 8.2 200 170 18 19 250 230 12 13
150 140 12.5 13.5 200 175 16 17 250 230 14 15
155 135 15 16 200 175 19 20 250 230 15 16
157 132 20 21 200 175 20 21 250 230 16 17
160 130 25 26 200 180 12 13 260 235 16 17
160 135 19 20 200 180 14 15 260 235 19 20
160 135 20 21 200 180 15 16 260 240 12 13
160 140 12 13 200 180 16 17 260 240 16 17
160 140 13.5 14.5 205 180 19 20 270 245 16 17
160 140 14 15 205 180 20 21 270 245 19 20
160 140 15 16 210 185 16 17 270 250 12 13
160 140 16 17 210 185 20 21 270 250 16 17
160 145 9 10 210 190 12 13 275 250 19 20
160 145 10 11 210 190 16 17 275 250 20 21
160 145 14 15 220 190 18 19 280 250 16 17
165 140 19 20 220 195 16 17 280 250 18 19
165 140 20 21 220 195 20 21 280 250 19 20
170 145 19 20 220 200 12 13 280 255 16 17
170 145 20 21 220 200 14 15 280 255 19 20
170 148 15 16 220 200 16 17 280 260 14 15
170 150 12 13 224 199 16 17 290 265 16 17
170 150 15 16 224 199 20 21 290 265 19 20
170 150 16 17 224 204 12 13 297 265 24 25
170 155 9 10 224 204 16 17 297 265 25 26
175 145 18 19 225 200 16 17 300 270 12 13
175 155 14 15 225 200 19 20 300 270 19 20
175 160 9 10 225 200 20 21 300 270 24 25
180 150 25 26 225 205 12 13 300 270 25 26
180 155 19 20 225 205 16 17 300 275 16 17
180 155 20 21 230 205 16 17 300 280 15 16
180 160 9 10 230 205 19 20 312 280 24 25
180 160 14 15 230 210 12 13 320 280 28 29
180 160 16 17 230 210 16 17 320 290 20 21
180 165 9 10 240 215 16 17 332 300 24 25
180 165 10 11 240 215 19 20 360 320 28 29
185 160 19 20 240 215 20 21 360 330 20 21
185 160 20 21 240 220 12 13 400 360 28 29
190 165 16 17 240 220 16 17 400 370 20 21
190 165 20 21 250 220 18 19 502 482 19 20
190 170 14 15 250 220 30 31 603 535 15 16

25
HRS MA24

piston rod seal with asymmetrical sealing lips Profile width (mm) Lead-in chamfer C (mm)
which are cut at an angle of less than 45°. 4 2
5 2.5
Standard material
7.5 4
NBR90
10 5
12.5 6.5
Area of application
15 7.5
Hydraulics and pneumatics
reciprocating movements 20 10
25 10

Function
The HRS MA24 is a single function piston rod seal If the housing is provided with a metallic
in the form of a U-ring. Due to its asymmetrical fitting on the side opposite the pressure, the
sealing lips with a slightly indented outer lip service life of the seal is lengthened. Within the
edge, the pressure is guided outwards to operating parameters given above, depending
strengthen its sealing function at low pressure. on the pressure, a metallic wedge can be fitted
between the cylinder pipe and piston acc. to
Media the following table:
Hydraulic oils acc. DIN 51524/51525,
lubricating oils, mineral oil based Pressure (MPa) Radial wedge G (mm)
lubricating fats, non-flammable 5 0.2
hydraulic fluids HFA, HFB, HFC acc. 10 0.15
VDMA 24317.
11 0.1

Operational application limits Please also follow the general installation


Pressure (MPa/bar): 16/160 instructions.
Temperature (°C): –30 to + 100
Running speed (m/s): = 0.5 Remarks
In addition, we are able to supply other
Installation dimensions required. For operating conditions
The HRS MA24, from an inner diameter of 25 other than the standard applications, further
mm and thin profile can always be installed elastomers are available.
in cut housing. With an inner diameter of less
than 25 mm, we recommend axially accessible
housing. To push the cylinder head and seal
over the piston rod without damaging it, a
lead-in chamfer C acc. to the following table is
required:

26
HRS MA24
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

2 4.5 1.7 2.7 25 32 6 7 55 70 10 11


2.5 5 1.7 2.7 25 33 5.5 6.5 56 68 7 8
3 6 2.5 3.5 25 33 7.5 8.5 56 68 8.5 9.5
3 6 3 4 25 33 8.5 9.5 60 70 8.5 9.5
4 8 3 4 25 33 10 11 60 70 10 11
4 9 3.5 4.5 25 35 6 7 60 72 8.5 9.5
4 12 4.5 5.5 25 35 6.5 7.5 60 74 8 9
5 9 2.5 3.5 25 35 7 8 60 75 12 13
6 10 3 4 25 35 7.5 8.5 63 75 8.5 9.5
6 11.5 3.2 4.2 25 35 8 9 65 75 10 11
6 12 4 5 25 35 10 11 65 77 8.5 9.5
6 12 4.2 5.2 25 37 6 7 68 74 4 5
6 13 5.5 6.5 25 40 10 11 68 80 8.5 9.5
7 11 3.96 5 28 36 5.5 6.5 69.8 84 11.2 12.2
8 14 4 5 28 36 5.7 6.7 70 80 12 13
8 16 5.5 6.5 28 38 6 7 70 82 8.5 9.5
8 16 6 7 28 38 7 8 70 85 10 11
9 15 9 10 28 38 8 9 75 85 12 13
10 16 4.5 5.5 28 38 10 11 80 90 12 13
10 18 5.5 6.5 30 37 7 8 80 92 8.5 9.5
12 18 4.5 5.5 30 38 6.3 7.3 80 92 9.5 10.5
12 19 4.5 5.5 30 40 6 7 85 95 7 8
12 20 5.5 6.5 30 40 7 8 85 95 12 13
12 22 7.5 8.5 30 40 8 9 88 110 16.5 17.5
12 22 8 9 30 42 8.5 9.5 90 100 12 13
14 19 3.5 4.5 32 42 7 8 90 102 8.5 9.5
14 22 5.5 6.5 32 48 8 9 91.8 106 11.2 12.2
15 23 6 7 34 44 7 8 95 105 12 13
15 25 5 6 35 45 6 7 100 112 8.5 9.5
16 20.5 5 6 35 45 7 8 100 115 10 11
16 22 5.5 6.5 35 45 8 9 105 120 12 13
16 22 6.5 7.5 35 50 8 9 110 125 10 11
16 22.5 4.5 5.5 36 46 7 8 110 130 14 15
16 24 5.5 6.5 36 46 8 9 113.8 128 11.2 12.2
16 25 5 6 36 46 10 11 115 125 12 13
16 26 7 8 40 48 8 9 120 135 9.5 10.5
16 26 7.5 8.5 40 50 5.5 6.5 125 145 14 15
18 25 4.5 5.5 40 50 7 8 135 145 12 13
18 25 5.5 6.5 40 50 8 9 135.8 150 11.2 12.2
18 26 5.5 6.5 40 50 10 11 140 160 14 15
20 28 5.5 6.5 40 55 10 11 155 165 12 13
20 28 6 7 42 52 7 8 160 170 12 13
20 30 6 7 45 55 7 8 160 180 14 15
20 30 7.5 8.5 45 55 10 11 161.8 176 11.2 12.2
20 30 10 11 45 61 12 13 180 200 14 15
20 32 6 7 50 56 8 9 185 195 12 13
20 32 7.5 8.5 50 60 6 7 210 240 28 29
20 34 8 9 50 60 7 8 215 225 12 13
22 30 5.5 6.5 50 60 10 11 220 30 8 9
22 30 7 8 52 62 10 11 240 250 12 13
22 32 6 7 55 65 7 8 245 290 25 26
24 32 5.5 6.5 55 65 10 11

27
HPRS MA25

piston and piston rod seal with symmetrical Profile width (mm) Lead-in chamfer C (mm)
sealing lips which are cut at an angle of less 4 2
than 45°. 5 2.5
7.5 4
Standard material
10 5
Polyurethane TPU92
12.5 6.5
15 7.5
Area of application
Hydraulics 20 10

reciprocating movements 25 10

Function If the housing is provided with a metallic


The HPRS MA25 is a single function piston seal fitting on the side opposite the pressure, the
in the form of a U-ring which can be used as a service life of the seal is lengthened. Within the
piston and piston rod seal due to its symmetrical operating parameters given above, depending
sealing lips. Its seal function is very effective due on the pressure, a metallic wedge can be fitted
to the sealing lips being provided with radial between the cylinder head and piston rod or
self energising which is activated by the system cylinder pipe and piston acc. to the following
pressure. Due to the high wear resistance of table:
polyurethane, this seal has a particularly long
service life. For new design we recommend HRS Pressure (MPa) Radial wedge G (mm)
MA30 or HPS MA28. 5 0.6
10 0.5
Media
20 0.35
Hydraulic oils acc. DIN 51524/51525,
30 0.3
lubricating oils, mineral oil based
lubricating fats, non-flammable The piston diameter d1 should generally be
hydraulic fluids HFA, HFB, HFC acc. by factor 1.0 of the profile smaller than the DN
VDMA 24317. diameter provided.

Operational application limits Please also follow the general installation


Pressure (MPa/bar): 30/300 instructions.
Temperature (°C): –40 to + 100
< +40 in HFa, HFB, HFC Remarks
Running speed (m/s): = 0.5 In addition, we are able to supply other
dimensions required. For operating conditions
Installation other than the standard applications, other
The HPRS MA25, from an inner diameter of polyurethane materials are available.
25 mm and a thinner profile can always be
installed in cut housing. Due to the high tensile
and strength of polyurethane, it is necessary to
use installation tools for thick seals. With an inner
diameter of less than 25 mm, we recommend
axially accessible housing. To push the piston
body and seal into the cylinder pipe or over
the piston rod without damaging it, a lead-
in chamfer C acc. to the following table is
required:

28
HPRS MA25
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

3 9 4.5 5 6 12 8 9 8 18 9 10
3 10 5 6 6 12.7 5.5 6.5 8 22 7 8
3 10 6 7 6 13 8 9 8 22 8 9
4 10 4 4.5 6 14 6 7 8 22 9 10
4 10 4.5 5.5 6 15 4 5 9 15 8 9
4 10 5 6 6 15 5 6 9 17 6 7
4 12 5.5 6.5 6 15 8 9 9 18 5 6
4 12 6 7 6 15 9 10 9 19 6 7
4 14 6 7 6 22 6 7 9 19 7 8
4.5 11 5 5.5 7 14 3.5 4.2 9 19 8 9
4.5 12.5 4.5 5 7 14 4 5 10 15 4 5
4.5 12.5 5 6 7 15 5 6 10 16 4 5
5 10 5 6 7 15 7 8 10 16 5 6
5 11 5 6 7 15 8 9 10 16 6 6.5
5 12 5 5.5 8 12 2.4 3.5 10 16 6.5 7.5
5 12 6.2 7 8 14 4 5 10 18 5 6
5 12 6 6.5 8 14 5 6 10 18 5.5 6
5 12 8 9 8 14 6 7 10 18 6 7
5 12.7 8 9 8 14 7 8 10 18 7 8
5 13 6 7 8 15 4 5 10 18 8 9
5 14 4.5 5.5 8 15 5.7 6.3 10 18 9 10
5 14 6 7 8 15 6 7 10 20 5 6
5 17 9 10 8 15 7 8 10 20 6 7
6 12 4 4.5 8 15 8 9 10 20 7 8
6 10 3 4 8 15 9 10 10 20 8 9
6 12 4.5 5 8 16 5.7 6.3 10 20 9 10
6 12 5 6 8 16 6 7 10 22 6 7
6 12 5.5 6.5 8 16 8 9 10 22 7 8
6 12 6 7 8 18 6 7 10 22 8 9
6 12 6.5 7.5 8 18 8 9 10 22 9 10

29
HPRS MA25
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

10 25 8 9 16 24 9 10 20 40 12 13
10 32 10 11 16 24 10 11 21 37 10 11
11 17 4.4 5 16 25 5 6 21 37 12 13
11 20.5 6 7 16 26 5 6 22 28 4 5
11 20.5 7 8 16 26 8 9 22 28 5.5 6.5
11 22 8 9 16 26 9 10 22 28 8 9
11 26 8 9 16 26 10 11 22 28 9 10
12 18 4 5 16 28 6 7 22 30 4 5
12 18 4.8 5.5 16 28 7 8 22 30 5 6
12 18 5 6 16 32 8 9 22 30 6 7
12 18 6 7 16 32 9 10 22 30 7 7.5
12 18 7 8 16 35 9 10 22 30 10 11
12 20 5 6 17 25 8 9 22 32 5 6
12 20 7 8 17 25 10 11 22 32 7 8
12 20 8 9 17 32 7 8 22 32 8 9
12 20 9 10 17 32 10 11 22 32 9 10
12 22 5 6 17 35 6 7 22 32 10 11
12 22 6 7 17 35 10 11 22 34 6 7
12 22 7 8 18 25 5 5.5 22 35 5 6
12 22 8 9 18 25 6 7 22 35 8 9
12 22 9 10 18 26 5 6 22 35 10 11
12 24 6 7 18 26 6 7 22 36 8 9
12 24 8 9 18 26 6.5 7.5 22 40 10 11
12 24 9 10 18 26 8 9 23 30 6.5 7.5
12 24 10 11 18 26 8.5 9.5 23 35 10 11
12 25 8 9 18 28 8 9 24 32 7 7.5
12 25 9 10 18 28 10 11 24 32 8 9
12 25 10 11 18 30 7.5 8.5 24 34 10 11
12 27 7.5 8.5 18 30 8 9 24 40
12 28 8 9 18 30 8.5 9.5 24 40 9 10
13 20 4.5 5.5 18 30 9 10 25 30 8 9
13 25 8 9 18 30 10 11 25 32 4 5
13 25 10 11 18 32 7 8 25 32 10 11
13 30 9 10 18 34 8 9 25 33 4 5
14 20 4 5 18 35 8 9 25 33 4.5 5.5
14 20 4.8 5.3 18 35 10 11 25 33 5 6
14 20 5 6 18 36 8 9 25 33 6 7
14 20 6 7 18 40 11 12 25 33 7 7.5
14 22 3.9 4.5 19 25 6 7 25 33 8 9
14 22 4.5 5 19 37 10 11 25 35 5 5.5
14 22 5 6 20 25 3 4 25 35 6 7
14 22 6 7 20 26 4 5 25 35 7 8
14 22 7 8 20 26 5 6 25 35 7.5 8.5
14 22 8 9 20 27 5 6 25 35 8 9
14 22 9 10 20 27 6 7 25 35 9 10
14 22 11 12 20 28 4 5 25 35 10 11
14 24 6 7 20 28 5 6 25 37 7 8
14 24 8 9 20 28 6 7 25 37 9 10
14 24 9 10 20 28 8 9 25 38 9.5 10.5
14 26 8 9 20 28 9 10 25 38 10 11
14 28 7 8 20 29 5 5.5 25 39 7 8
14 28 10 11 20 30 6 7 25 40 8 9
15 20 3 4 20 30 7.5 8.5 25 40 10 11
15 22 4 5 20 30 8 9 25 45 10 11
15 22 7 8 20 30 9 10 26 35 5 6
15 25 5 6 20 30 10 11 26 36 7 8
15 25 6 7 20 32 5 6 26 38 8 9
15 25 8 9 20 32 6 7 26 47 12 13
15 25 9 10 20 32 7.5 8.5 27 35 4 5
15 25 10 11 20 32 8 9 27 36 6 7
15 27 6 7 20 33 8 9 27 38 6 7
15 27 7 8 20 35 10 11 28 35 5 5.5
15 28 8 9 20 35 12 13 28 35.5 5 6
15 28 10 11 20 36 8 9 28 36 4 5
15 30 6 7 20 36 12 13 28 36 5 6
15 30 8 9 20 37 12 13 28 36 6 7
16 22 4 4.5 20 38 9 10 28 36 6.5 7.5
16 22 5 5.5 20 39 10 11 28 38 7 8
16 24 4 5 20 40 10 11 28 38 8 9
16 24 5 6 20 40 11 12 28 38 9 10

30
HPRS MA25
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

28 38 10 11 35 50 9 10 45 53 8 9
28 40 8 9 35 50 10 11 45 53 10 11
28 40 10 11 35 55 10 11 45 53 12 13
28 43 10 11 35 55 12 13 45 55 5 6
28 44 8 9 35.5 45 6 7 45 55 6 7
28 44 10 11 36 44 4 5 45 55 6.5 7.5
28 46 10 11 36 44 5.7 6.5 45 55 7 8
28 47 10 11 36 45 10 11 45 55 10 11
28 48 12 13 36 46 7 8 45 55 11 12
30 37 5.8 6.8 36 46 8 9 45 55 12 13
30 37 6 7 36 46 10 11 45 56 7 8
30 38 5 6 36 48 8 9 45 57 6 7
30 38 6 6.5 36 50 8 9 45 58 12 13
30 38 6.5 7.5 36 51 10 11 45 60 9 10
30 38 7 8 36 52 10 11 45 60 10 11
30 38 8 9 36 55 10 11 45 63 9 10
30 40 5 5.5 36 70 10 11 45 63 10 11
30 40 5.5 6.5 38 40 8 9 45 63 12 13
30 40 6 7 38 45 5 5.5 45 65 10 11
30 40 6.5 7.5 38 45 6 7 45 65 12 13
30 40 7 8 38 45 8 9 45 65 18 19
30 40 8 9 38 45 10 11 45 70 10 11
30 40 10 11 38 46 6 7 45 70 12 13
30 42 6 7 38 46 6.5 7.5 45 75 15 16
30 42 9 10 38 50 6 7 46 70 12 13
30 42 10 11 38 50 9 10 47 57 10.2 11
30 43 6.5 7.5 38 50 10 11 47 62 12 13
30 45 9 10 38 52.5 9.5 10.5 47 65 12 13
30 45 10 11 38 55 10 11 48 58 10 11
30 46 10 11 38 55 12 13 48 60 9 10
30 50 10 11 38 58 10 11 48 63 10
30 50 12 13 38 60 12 13 48 63 12 13
30 52 11 12 40 48 5 6 48 65 10 11
31 38 7 8 40 48 8 9 48 68 10 11
32 40 4 5 40 48 11 12 50 57 10 11
32 40 5 6 40 50 5 6 50 58 8 9
32 40 5.5 6.5 40 50 6 7 50 60 5 6
32 40 6 7 40 50 6.5 7.5 50 60 6 7
32 40 7 8 40 50 7 8 50 60 7.2 8
32 40 8 9 40 50 7.5 8.5 50 60 8 9
32 40 10 11 40 50 8 9 50 60 9 10
32 42 6 7 40 50 10 11 50 60 10 11
32 42 10 11 40 52 8 9 50 60 11 12
32 45 10 11 40 52 9 10 50 60 12 13
32 47 10 11 40 55 10 11 50 60 13 14
32 50 10 11 40 56 8 9 50 62 9 10
32 50 12 13 40 56 10 11 50 62 10 11
32 52 10 11 40 60 10 11 50 63 6 7
33 43 10 11 40 60 12 13 50 63 7 8
33 46 10 11 40 60 13 14 50 63 8 9
34 42 8 9 40 60 18 19 50 63 9 10
34 45 7 8 40 64 12 13 50 63 10 11
34 45 8 9 40 65 10 11 50 65 8 9
34 45 9 10 40 65 12 13 50 65 9 10
34 46 8 9 40 65 13 14 50 65 10 11
34 50 14 15 40 70 15 16 50 65 12 13
34 74 10 11 40 75 10 11 50 70 8 9
35 42 8 9 40 80 10 11 50 70 10 11
35 43 6 7 42 50 5 6 50 70 12 13
35 43 7 8 42 50 8 9 50 70 18 19
35 43 8 9 42 50 9 10 50 72 12 13
35 45 6 7 42 50 10 11 50 74 15 16
35 45 7.5 8.5 42 52 6 7 50 75 12 13
35 45 8 9 42 52 9 10 50 75 15 16
35 45 9 10 42 52 10 11 50 76 12 13
35 45 10 11 42 62 12 13 50 80 10 11
35 47 10 11 44 54 6 7 50 80 18 19
35 48 10 11 44 64 10 11 52 62 12 13
35 50 7 8 45 53 5.7 6.5 52 68 8 9
35 50 8 9 45 53 6.5 7.5 52 80 15 16

31
HPRS MA25
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

53 63 5 6 65 82 12 13 80 92 11.5 12.5
53 63 6 7 65 85 10 11 80 95 7.5 8.5
53 63 6.5 7.5 65 85 12 13 80 95 8 9
54 72 10 11 65 85 18 19 80 95 9 10
55 65 5 6 65 86 12 13 80 95 10 11
55 65 6 7 65 90 8 9 80 95 12 13
55 65 10 11 65 90 12 13 80 100 10 11
55 65 12 13 65 90 13 14 80 100 12 13
55 70 7.5 8.5 65 90 15 16 80 100 13.5 14.5
55 70 9 10 65 90 18 19 80 100 18 19
55 70 10 11 65 95 12 13 80 105 12 13
55 70 12 13 65 106 25 26 80 105 22 23
55 75 10 11 66 76 8 9 82 92 10 11
55 75 12 13 66 80 10 11 83 103 14 15
55 75 18 19 66 80 13 14 84 100 8 9
55 76 10 11 67 77 10 11 84.5 94 8 8.8
55 80 10 11 67 77 12 85 95 8.5 9.5
55 80 12 13 67 80 12 13 85 95 9 10
55 80 15 16 68 92 15 16 85 95 12 13
55 80 18 19 70 80 5 6 85 100 8 9
56 66 6.7 7.5 70 80 6 7 85 100 9 10
56 70 12 13 70 80 7 8 85 100 11 12
56 71 10 11 70 80 8 9 85 100 12 13
56 76 12 13 70 80 10 11 85 100 25 26
56 80 15 16 70 80 12 13 85 105 10 11
60 68 8 9 70 81 15 16 85 105 12 13
60 68 10 11 70 82 10 11 85 105 15 16
60 68 12 13 70 85 8 9 85 105 18 19
60 68 12.5 13.5 70 85 9 10 85 110 12 13
60 70 5 6 70 85 10 11 85 115 15 16
60 70 6 7 70 85 12 13 86 106 10 11
60 70 7.5 8.5 70 90 10 11 87 102 13 14
60 70 8 9 70 90 12 13 88 96 8 9
60 70 10 11 70 90 13.5 14.5 88 108 12 13
60 70 12 13 70 90 18 19 89 100 12 13
60 70 13 14 70 95 10 11 90 98 12 13
60 75 8 9 70 95 12 13 90 100 5 6
60 75 9 10 70 100 15 16 90 100 6 7
60 75 10 11 70 105 15 16 90 100 7 8
60 75 12 13 72 90 10 11 90 100 8 9
60 80 10 11 72 90 11 12 90 100 10.5 11.5
60 80 12 13 72 90 12 13 90 100 12 13
60 80 13.5 14.5 72 96 12 13 90 100 15 16
60 80 18 19 75 85 6 7 90 102 9 10
60 85 10 11 75 85 10 11 90 105 9 10
60 85 12 13 75 85 12 13 90 105 12 13
60 85 12.5 13.5 75 87 9 10 90 110 8 9
60 90 15 16 75 90 7.5 8.5 90 110 8.4 9.5
61 80 12 13 75 90 9 10 90 110 10 11
62 72 12.5 13.5 75 90 10 11 90 110 12 13
62 75 10 11 75 90 12 13 90 110 15 16
63 73 5 6 75 90 15 16 90 110 18 19
63 75 10 11 75 95 10 11 90 115 12 13
63 75 12 13 75 95 12 13 90 115 15 16
63 78 10 11 75 95 13.5 14.5 90 115 22 23
63 80 9 10 75 100 12 13 90 120 15 16
63 80 10 11 75 100 15 16 94 124 15 16
63 83 12 13 75 100 22 23 95 105 11 12
63 83 13 14 75 105 15 16 95 105 12 13
63 83 15 16 78 86 12.5 13.5 95 110 9 10
64 76 9 10 78 93 10.5 11.5 95 110 10 11
64 80 8 9 78 100 15 16 95 110 12 13
65 73 12 13 80 90 5 6 95 110 15 16
65 75 6 7 80 90 5.4 6.5 95 112 11 12
65 75 10 11 80 90 6 7 95 115 12 13
65 75 12 13 80 90 8 9 95 115 15 14
65 80 9 10 80 90 10 11 95 115 18 19
65 80 10 11 80 90 12 13 95 120 12 13
65 80 11 12 80 90 13.5 14.5 95 125 12 13
65 80 12 13 80 92 9 10 100 110 5 6

32
HPRS MA25
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

100 110 8 9 127 142 12 13 190 215 15 16


100 115 9 10 130 145 15 16 190 220 15 16
100 115 12 13 130 150 10 11 190 220 25 26
100 115 14 15 130 150 12 13 190 220 26 27
100 120 10 11 130 150 15 16 200 220 10 11
100 120 12 13 130 157 15 16 200 220 15 16
100 120 13.5 14.5 130 160 15 16 200 225 18 19
100 120 15 16 130 160 18 19 200 230 17 18
100 120 18 19 132 144 12 13 200 230 18 19
100 125 10 11 133 149 11 12 200 230 22 23
100 125 12 13 135 150 15 16 200 235 20 21
100 125 15 16 135 155 15 16 200 238 22 23
100 130 12 13 135 160 15 16 200 240 20 21
100 130 15 16 135 165 15 16 205 225 12 13
100 130 18 19 140 150 5 6 205 235 18 19
105 120 8 9 140 155 15 16 210 235 18 19
105 120 15 16 140 160 6 7 210 240 18 19
105 125 10 11 140 160 12 13 210 250 20 21
105 125 12 13 140 160 15 16 212 237 18 19
105 125 14 15 140 165 15 16 220 240 15 16
105 125 15 16 140 165 18 19 220 250 15 16
105 125 16 17 140 170 17 18 220 250 18 19
105 135 18 19 140 170 18 19 220 250 20 21
106 120 8.5 9.5 145 160 8 9 220 255 22 23
107 130 15 16 145 160 9 10 220 255 30 31
108 116 11.5 12.5 145 165 15 16 220 265 22 23
110 125 12 13 145 170 18 19 224 249 18 19
110 125 15 16 146 170 14 15 225 245 15 16
110 130 12 13 148 160 9.5 10.5 225 250 18 19
110 130 15 16 150 160 12 13 225 255 42 43
110 130 18 19 150 160 13.5 14.5 225 265 34 35
110 135 18 19 150 170 15 16 229 263 20 21
110 140 18 19 150 170 18 19 230 250 12 13
110 150 20 21 150 180 13.5 14.5 230 250 15 16
112 132 12 13 150 180 15 16 230 255 18 19
113 125 9.5 10.5 150 180 18 19 230 260 18 19
114 124 10 11 153 165 12 13 235 255 12 13
115 125 8 9 154 169 11 12 236 261 18 19
115 125 15 16 155 175 15 16 240 260 16 17
115 126 15 16 155 180 15 16 240 260 17 18
115 129 13 14 157 170 12 13 240 260 18 19
115 130 15 16 160 175 7.5 8.5 240 265 18 19
115 135 12 13 160 180 15 16 245 270 15 16
115 135 15 16 160 185 15 16 250 280 22 23
115 140 15 16 160 190 15 16 255 280 18 19
115 140 18 19 160 190 22 23 260 290 18 19
115 140 22 23 165 190 15 16 260 296 34 35
115 155 20 21 165 215 20 21 260 300 20 21
120 130 5 6 170 190 15 16 260 300 26 27
120 130 14 15 170 195 15 16 265 290 17 18
120 135 15 16 170 200 15 16 265 295 18 19
120 140 10 11 170 200 18 19 270 290 17 18
120 140 10.5 11.5 170 202 26 27 270 300 15 16
120 140 12 13 170 212 20 21 270 310 20 21
120 140 15 16 170 215 20 21 280 300 15 16
120 145 18 19 175 187 12 13 280 310 18 19
120 150 15 16 175 200 15 16 280 310 21 22
125 135 10 11 175 215 20 21 296 325 14 15
125 140 11 12 180 200 15 16 300 330 18 19
125 140 12 13 180 200 18 19 305 320 17 18
125 140 15 16 180 205 15 16 310 330 17 18
125 145 12 13 180 210 15 16 320 350 15 16
125 145 15 16 180 210 22 23 320 350 16 17
125 145 18 19 180 220 16 17 320 360 20 21
125 147 12 13 180 220 20 21 330 360 22 23
125 150 12 13 185 200 7.5 8.5 355 375 22 23
125 150 18 19 185 200 9 10 360 390 22 23
125 155 15 16 185 205 15 16 500 540 34 35
125 155 18 19 190 204 15 16 530 565 25 26
125 165 20 21 190 210 15 16

33
HPS MA28

piston seal with asymmetrical sealing lips which Profile width (mm) Lead-in chamfer C (mm)
are cut at an angle of less than 45°. 4 2
5 2.5
Standard material
7.5 4
Polyurethane TPU92
10 5
12.5 6.5
Area of application
15 7.5
Hydraulics
reciprocating movements 20 10

extreme loads 25 10

Function If the housing is provided with a metallic


The HPS MA28 is a single function piston seal in fitting on the side opposite the pressure, the
the form of a U-ring. Its excellent suitability for service life of the seal is lengthened. Within the
extreme loads, which is for example required operating parameters given above, depending
for application in the working cylinders of on the pressure, a metallic wedge can be fitted
heavy earth-moving machines, is provided between the cylinder pipe and piston acc. to
by the synergy between the geometric of this the following table:
seal and the special material characteristics of
polyurethane. It guarantees effective sealing Pressure (MPa) Radial wedge G (mm)
at low and zero pressures as well as the most 5 0.6
difficult operational conditions which would 10 0.5
overload.
20 0.35
30 0.3
Media
40 0.25
Hydraulic oils acc. DIN 51524/51525,
lubricating oils, mineral oil based The piston diameter d1 should generally be
lubricating fats, non-flammable by factor 1.0 of the profile smaller than the DN
hydraulic fluids HFA, HFB, HFC acc. diameter provided.
VDMA 24317.
Please also follow the general installation
Operational application limits instructions.
Pressure (MPa/bar): 40/400
Temperature (°C): –40 to + 100 Remarks
< +40 in HFA, HFB, HFC In addition, we are able to supply other
Running speed (m/s): = 0.5 dimensions required. For operating conditions
other than the standard applications, other
Installation polyurethane materials are available.
The HPS MA28, with a thin profile can always be
installed in cut housing. Due to the high strength
of polyurethane, it is necessary to use intallation
tools for thick seals. To push the piston body and
seal into the cylinder pipe without damaging it,
a lead-in chamfer C acc. to the following table
is required:

34
HPS MA28
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

11 6 7 8 30 15 10 11 40 25 9 10
12 5 5.5 6 30 17 10 11 40 25 10 11
12 6 4 5 30 20 5 6 40 27 8 9
14 6 8 9 30 20 6 7 40 27 10 11
14 8 4.5 5.5 30 20 7 8 40 28 10 11
14 8 6.3 6.8 30 20 8 9 40 30 6.5 7.5
15 9 8 9 30 22 6.5 7 40 30 7 8
16 6 8 9 30 22 10 11 40 30 10 11
16 6 10 11 32 17 10 11 40 32 5.7 6.3
16 8 5.7 6.3 32 22 7.3 8 40 32 8 9
16 10 4 5 32 22 8 9 40 33 8 9
16 10 6 6.5 32 22 10 11 42 22 10 11
16 10 6.5 7.5 32 24 5.5 6.3 42 30 10 11
16 10 8 9 32 24 5.7 6.7 42 32 10 11
18 8 7.5 8.5 32 25 5 5.6 42 34.5 4.2 4.7
18 10 6 7 32 26 5 6 43 25 9 10
20 10 6 7 34 22 8.4 9.4 43 30 10 11
20 10 7.5 8.5 34 22 9 10 43 33 7.3 8
20 10 8 9 35 18 12 13 43 35 9 10
20 12 5 6 35 20 10 11 44 20 11 12
20 12 5.5 6.3 35 22 10 11 44 36 7 8
20 12 6.5 7.5 35 25 6 7 45 25 12 13
20 12 7 8 35 25 6.5 7.5 45 28.5 12 13
20 12 7.5 8.5 35 25 7 8 45 30 9 10
20 14 5.5 6 35 25 7.3 8.3 45 30 10 11
22 12 8 9 35 25 8 9 45 32 8 9
22 14 5 6 35 27 5 6 45 32 10 11
23.5 15 8 9 35 27 10 11 45 33 9 10
24 16 5.7 6.3 35.4 22.4 10 11 45 35 6 7
25 10 10 11 35.5 22.5 8 9 45 35 8 9
25 13 7 8 35.5 22.5 10 11 45 38 6 7
25 15 7.3 8 35.5 25.5 6 7 48 28 12 13
25 15 8 9 35.5 25.5 8 9 48 35 10 11
25 17 5.5 6.3 35.5 27.5 5 6 48 38 8 9
25 17 10 11 36 28 7 8 50 30 12 13
25 18 5 5.6 36.5 24 6.2 7 50 32 10 11
26 16 7.5 8.5 37 21 12 13 50 34 10 11
26 18 5 6 38 22 10 11 50 34 12 13
26 18 7 8 38 25 10 11 50 35 8.5 9.5
26 20 6 7 38 30 6.5 7.5 50 35 10 11
28 15 10 11 38 31 4.7 5.2 50 35 12 13
28 20 5 6 40 20 12 13 50 40 5 5.5

35
HPS MA28
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

50 40 6 7 70 60 6 7 95 75 13.5 14.5
50 40 7 8 70 60 7 8 95 75 15 16
50 40 8 9 70 60 8 9 95 80 9 10
50 40 10 11 70 60 12 13 95 80 10 11
50 42 5.5 6 70 60 13.5 14.5 95 80 12 13
50 42 8 9 70 62 7.5 8.5 95 85 6.7 7.5
50 42 10 11 71 51 12 13 95 85 7 8
50.8 40.8 7 8 71 55 10 11 95 85 8.5 9.5
52 42 10 10.6 71 55 12 13 95 85 13.5 14.5
54 44 7.3 8 71 56 9 10 100 80 10 11
55 35 12 13 71 56 10 11 100 80 12 13
55 40 10 11 71 60 7 8 100 80 13.5 14.5
55 45 6 7 71 61 6 7 100 80 15 16
55 45 7 8 71 61 8 9 100 85 9 10
55 45 8 9 72 58 12 13 100 85 11.4 12.5
55 45 10 11 73 63 6 7 100 85 12 13
55 47 5.7 6.3 75 50 14 15 100 86 12 13
56 40 10 11 75 55 12 13 100 88 10 11
56 40 12 13 75 55 13.5 14.5 100 90 7 8
56 41 9 10 75 60 9 10 100 90 8.5 9.5
56 41 10 11 75 60 10 11 100 90 10.5 11.5
56 45 7 8 75 60 12 13 101.6 80 12 13
56 46 6 7 75 63 8.7 9.5 105 85 15 16
57 41 11.4 12.5 75 65 5 5.5 105 90 9 10
60 40 12 13 75 65 6.7 7.5 105 90 12 13
60 40 13.5 14.5 75 65 7 8 105 95 12 13
60 45 9 10 75 65 8 9 110 85 15 16
60 45 10 11 75 65 10 11 110 90 12 13
60 50 5 5.5 75 65 13.5 14.5 110 90 15 16
60 50 6 7 76 60 12 13 110 95 9 10
60 50 7 8 77 67 6 7 110 95 10 11
60 50 8 9 80 60 12 13 110 95 12 13
60 50 10 11 80 60 13.5 14.5 110 100 7 8
60 52 8 9 80 60 14.5 16 110 100 13.5 14.5
61 45 12 13 80 64 12 13 112 92 12 13
63 43 12 13 80 65 8.6 9.5 112 92 15 16
63 45 10 11 80 65 11.4 12.5 112 97 9 10
63 45 12 13 80 65 12 13 112 97 10 11
63 47 12 13 80 68 8.5 9.5 112 98 8.5 9.5
63 48 9 9.5 80 70 6.7 7.5 115 90 15 16
63 48 10 11 80 70 7 8 115 95 15 16
63 48 11.4 12.5 80 70 8 9 115 100 6 7
63 48 12 13 80 70 12 13 115 100 9 10
63 53 6 7 80 71 6 7 115 100 10.5 11.5
63 53 7 8 80 72 12 13 115 105 13.5 14.5
63 53 12 13 82 65 12 13 120 95 12 13
63 55 5.7 6.3 85 65 12 13 120 95 15 16
65 45 12 13 85 65 13.5 14.5 120 100 12 13
65 45 13.5 14.5 85 70 9 10 120 100 13.5 14.5
65 50 9 10 85 70 10 11 120 100 15 16
65 50 10 11 85 70 12 13 120 103 16 17
65 50 11.5 12.5 85 75 6 7 120 105 9 10
65 55 7.3 8 85 75 8 9 120 105 10 11
65 55 8 9 85 75 10 11 120 105 12 13
65 55 10 11 85 75 12 13 120 106 8.5 9.5
65 55 13.5 14.5 90 65 12 13 124 103 16.5 17.5
66 50 12 13 90 70 12 13 125 95 18 19
67 57 7.3 8 90 70 13.5 14.5 125 100 15 16
68 48 10 11 90 70 15 16 125 105 12 13
68 52 8 9 90 75 9 10 125 105 15 16
68 58 9.5 10.5 90 75 11.4 12.5 125 105 16 17
68 60 8 9 90 75 12 13 125 110 9.6 10.6
70 50 12 13 90 80 5 5.5 125 110 10 11
70 50 13.5 14.5 90 80 6 7 125 112 9 10
70 50 15 16 90 80 8 9 125 115 7 8
70 55 9 10 90 80 9.5 10.5 125 115 15 16
70 55 9.5 10.5 90 80 10 11 130 110 12 13
70 55 10 11 90 80 13 14 130 110 15 16
70 55 12 13 90 80 13.5 14.5 130 110 16 17
70 58 8.5 9.5 95 75 12 13 130 115 9 10

36
HPS MA28
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

130 115 10 11 170 145 20 21 220 200 16 17


130 120 13.5 14.5 170 150 12 13 224 199 16 17
132 112 15 16 170 150 15 16 224 199 20 21
137 87 25 26 170 150 16 17 224 204 12 13
140 114 12 13 170 155 9 10 224 204 16 17
140 115 15 16 170 155 10 11 225 200 16 17
140 120 12 13 175 155 14 15 225 200 19 20
140 120 15 16 175 160 9 10 225 200 20 21
140 120 16 17 180 150 18 19 225 205 12 13
140 125 9 10 180 155 16 17 225 205 16 17
140 125 10 11 180 155 19 20 225 213 15 16
140 125 15 16 180 155 20 21 230 205 16 17
142 130 12 13 180 160 12 13 230 205 19 20
145 115 18 18.6 180 160 13.5 14.5 230 205 20 21
145 130 10 11 180 160 15 16 230 210 12 13
150 120 18 19 180 165 9 10 230 210 16 17
150 125 13.5 14.5 180 165 10 11 240 215 16 17
150 125 19 20 180 166 15.5 16.5 240 215 19 20
150 125 20 21 185 160 19 20 240 215 20 21
150 130 12 13 185 160 20 21 240 220 12 13
150 130 15 16 190 165 16 17 240 220 16 17
150 130 16 17 190 165 20 21 250 220 18 19
150 135 9 10 190 170 12 13 250 225 16 17
150 135 10 11 190 170 15 16 250 225 19 20
150 136 8.5 9.5 190 170 16 17 250 225 20 21
150 140 7 8 190 175 9 10 250 230 12 13
155 140 9 10 200 170 18 19 250 230 15 16
155 143 12 13 200 170 22.7 25 250 230 16 17
157 132 20 21 200 175 16 17 250 238 14 15
160 130 18 19 200 175 19 20 280 250 18 19
160 135 18.5 20 200 175 20 21 300 288 14 15
160 135 20 21 200 180 12 13 310 280 22 23
160 140 12 13 200 180 15 16 320 280 28 29
160 140 13.5 14.5 200 185 9.6 10.6 320 285 20 21
160 140 14 15 205 180 19 20 320 290 20 21
160 140 15 16 205 180 20 21 320 295 18 19
160 140 16 17 210 185 16 17 360 320 28 29
160 145 9 10 210 185 20 21 360 330 15 16
160 145 10 11 210 190 12 13 360 330 20 21
160 145 14 15 210 190 16 17 400 360 28 29
160 148 7.1 7.5 220 190 18 19 400 370 20 21
160 148 15.5 16.5 220 195 16 17
165 140 19 20 220 195 20 21
165 140 20 21 220 200 12 13
170 145 19 20 220 200 15 16

37
HRS MA30

piston rod seal with asymmetrical sealing lips Profile width (mm) Lead-in chamfer C (mm)
which are cut at an angle of less than 45°. 4 2
5 2.5
Standard material
7.5 4
Polyurethane TPU92
10 5
12.5 6.5
Area of application
15 7.5
Hydraulics
reciprocating movements 20 10

extreme loads 25 10

Function If the housing is provided with a metallic


The HRS MA30 is a single function piston seal in fitting on the side opposite the pressure, the
the form of a U-ring. Its excellent suitability for service life of the seal is lengthened. Within the
extreme loads, which is for example required operating parameters given above, depending
for application in the working cylinders of on the pressure, a metallic wedge can be fitted
heavy earth-moving machines, is provided between the cylinder pipe and piston acc. to
by the synergy between the geometric of this the following table:
seal and the special material characteristics of
polyurethane. It guarantees effective sealing Pressure (MPa) Radial wedge G (mm)
at low and zero pressures as well as the most 5 0.6
difficult operational conditions which would 10 0.5
overload conventional elastomer or fabric
20 0.35
U-rings.
30 0.3
40 0.25
Media
Hydraulic oils acc. DIN 51524/51525,
lubricating oils, mineral oil based Please also follow the general installation
lubricating fats, non-flammable instructions.
hydraulic fluids HFA, HFB, HFC acc.
VDMA 24317. Remarks
In addition, we are able to supply other
Operational application limits dimensions required. For operating conditions
Pressure (MPa/bar): 40/400 other than the standard applications, other
Temperature (°C): –40 to + 100 polyurethane materials are available.
< +40 in HFA; HFB; HFC
Running speed (m/s): = 0.5

Installation
The HRS MA30, from an inner diameter of 25
mm and a thin profile, can always be installed
in cut housing. Due to the high strength of
polyurethane, it is necessary to use installation
tools for thick seals. With an inner diameter
of less than 25 mm, we recommend axially
accessible housing. To push the cylinder head
and seal over the piston rod without damaging
it, a lead-in chamfer C acc. to the following
table is required:

38
HRS MA30
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

6 10 3 3.5 16 26 9 10 25 35 7.5 8.5


6 12 4.5 5.2 18 24 4.7 5.2 25 35 8 9
6 12 5.5 5.8 18 25 5 5.6 25 35 10 11
6 13 5 5.6 18 26 5.7 6.3 25 37 6 7
6 14 5.7 6.3 18 26 6 7 25 38 9 10
8 14 4.5 5.2 18 26 8 9 25 40 10 11
8 14.4 9.5 10.5 18 28 7.2 8 25 40 11 12
8 16 5.7 6.3 18 28 8 9 28 36 5.7 6.3
8 16 6 7 20 26 3.5 3.9 28 36 6 7
8 16 8 9 20 26 5 5.6 28 36 8 9
8 18 8 9 20 27 6 7 28 38 6 7
8 20 8 9 20 28 4 5 28 38 7.2 8
9 16 5.7 6.3 20 28 5.7 6.3 28 38 8 9
10 16 4.5 5.2 20 28 6.2 7 28 38 10 11
10 17 5.7 6.3 20 28 7.2 8 28 39 8 9
10 18 5.7 6.3 20 30 6 7 28 40 8.5 9.5
10 18 6 7 20 30 7.2 8 28 40 10 11
10 20 7.2 8 20 30 8 9 28 43 11.5 12.5
10 20 8 9 20 30 10 11 28 48 18 19
12 18 5 5.5 20 32 7.5 8.5 29 35 5.7 6.3
12 19 5 5.6 20 35 10 11 30 38 5.7 6.3
12 20 5.7 6.3 20 40 20 21 30 38 6.3 7
12 20 6 7 22 29 5 5.6 30 38 8 9
12 22 7.2 8 22 30 5.7 6.3 30 40 5.7 6.3
12 22 8 9 22 30 7 8 30 40 6 7
14 21 5 5.6 22 30 8 9 30 40 7 8
14 22 5.7 6.3 22 32 6 7 30 40 7.2 8.2
14 22 6 7 22 32 7.2 8 30 40 8 9
14 24 7.2 8 22 32 8 9 30 40 9.5 10.5
14 24 8 9 22 32 10 11 30 40 10 11
15 23 5.7 6.3 23 40 18 19 30 40 10.3 11.3
15 23 10 11 24 34 7.2 8 30 43 9 10
15 25 8 9 24 34 8.5 9.5 30 45 8 9
15 26 7.2 8 25 32 6 7 30 45 10 11
15 27 12 13 25 33 5.7 6.3 32 40 5.7 6.3
16 20.6 3.3 3.6 25 33 6.2 7 32 40 6.7 7.5
16 22 5 5.5 25 33 6.5 7.3 32 40 8 9
16 22 10 11 25 33 7.2 8 32 42 7 8
16 24 5.7 6.3 25 33 8 9 32 42 7.2 8
16 24 6.2 7 25 33 10 11 32 42 7.5 8.5
16 26 7.2 8 25 35 6 7 32 42 8 9
16 26 8 9 25 35 7.2 8 32 42 10 11

39
HRS MA30
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

32 42.53 8 9 50 60 6 7 65 75 13.5 14.5


32 45 9.5 10.5 50 60 7.2 8 65 77 8.6 9.6
32 45 10 11 50 60 7.5 8.5 65 77 9 10
32 47 10 11 50 60 10 11 65 78 10 11
33 43 10 11 50 60 12 13 65 80 10 11
35 43 5.7 6.3 50 62 8 9 65 80 12 13
35 43 8 9 50 62.7 9.5 10.5 65 85 12 13
35 45 6 7 50 65 10 11 65 85 13.5 14.5
35 45 7.2 8 50 65 11.5 12.5 69.85 85 13 14
35 45 8 9 50 68 9 10 70 78 8 9
35 45 10 11 50 70 10 11 70 78 12 13
35 45 12.5 13.5 50 70 12 13 70 80 6 6.5
35 46 8 9 50 70 13.5 14.5 70 80 6.5 7.5
35 46 9 10 50 70 14 15.5 70 80 7.2 8
35 50 8 9 52 62 10 11 70 80 10 11
35 50 10 11 55 63 7 8 70 80 12 13
35 55 12 13 55 63 8 9 70 82 9 9.6
36 44 5.7 6.3 55 63 12 13 70 83 10 11
36 44 8 9 55 65 7.2 8 70 85 10 11
36 46 7.2 8 55 65 10 11 70 85 11.5 12.5
36 46 8 9 55 65 12 13 70 85 12 13
36 46 10 11 55 65 13.5 14.5 70 90 12 13
36 48 7.2 8 55 67 10 11 70 90 13.5 14.5
36 48 8 9 55 70 10 11 70 90 15 16
36 51 10 11 55 70 12 13 72 80 12 13
36 51 11.5 12.5 55 75 12 13 73 82.5 7.2 8
36 56 12 13 55 75 13.5 14.5 73 94 15 16
37 45 5.7 6.3 56 66 6.5 7.5 75 85 7.2 8
37 47 10 11 56 66 7 8 75 85 12 13
38 44.5 4.7 5.3 56 66 8 9 75 85 13.5 14.5
38 45 5 5.5 56 66 10 11 75 87 8.6 9.6
38 45 6 7 56 68 9.5 10.5 75 90 10 11
38 45 6.2 7 56 71 8.6 9.5 75 90 12 13
38 50 10 11 56 71 10 11 75 95 12 13
40 48 5.7 6.3 56 71 11.5 12.5 75 95 13.5 14.5
40 48 8 9 56 71 12 13 76 84 7.5 8.5
40 48 11 12 56 76 12 13 80 90 7.2 8
40 49.52 9.5 10.5 56 76 13.5 14.5 80 90 10.5 11
40 50 7.2 8 56 76 15 16 80 90 12 13
40 50 8 9 60 68 8 9 80 90 14 15
40 50 10 11 60 70 7.2 8 80 92 8.6 9.6
40 50 12.5 13.5 60 70 10 11 80 92 10 11
40 52 8 9 60 70 12 13 80 93 10 11
40 55 7.2 8 60 70 13.5 14.5 80 95 10 11
40 55 10 11 60 72 8 9 80 95 11.5 12.5
40 55 11.5 12.5 60 72 9 10 80 95 12 13
40 60 12 13 60 72 9.5 10.5 80 100 12 13
42 50 5.7 6.3 60 75 10 11 80 100 13.5 14.5
42 50 6.5 7.5 60 75 11.5 12.5 80 100 15 16
42 52 10 11 60 75 12 13 82.55 98.5 13 14
42 62 10 11 60 77 11 12 85 94 14 15
42 62 12 13 60 80 12 13 85 95 7.2 8
45 53 5.7 6.3 60 80 13.5 14.5 85 95 12 13
45 53 8 9 61 69 7.5 8.5 85 97 8.6 9.6
45 53 10 11 62 74 13 14 85 100 11 12
45 53 12 13 62.5 75.1 7.5 8.5 85 100 11.5 12.5
45 55 5.7 6.3 63 73 6.5 7.5 85 100 12 13
45 55 7.2 8 63 73 10 11 85 105 12 13
45 55 7.5 8.5 63 73 12 13 85 105 13.5 14.5
45 55 10 11 63 75 8.7 9.6 90 100 6.5 7.5
45 57 9 10 63 75 9.5 10.5 90 100 10 11
45 57.7 9.5 10.5 63 75 10 11 90 100 11.5 12.5
45 58 9 10 63 78 10 11 90 100 12 13
45 60 10 11 63 78 11.5 12.5 90 102 9 10
45 60 11.5 12.5 63 78 12 13 90 102 10 11
45 65 10 11 63 83 12 13 90 105 8.5 9.5
45 65 12 13 63 83 13.5 14.5 90 105 9.5 10.5
45 65 13.5 14.5 63 83 15 16 90 105 10 11
46 56 7.2 8 65 75 10 11 90 105 11.5 12.5
50 58 8 9 65 75 12 13 90 105 12 13

40
HRS MA30
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

90 110 12 13 120 130 7.2 8 160 180 15 16


90 110 15 16 120 130 11.5 12.5 160 185 15 16
91 99 7.5 8.5 120 130 13.5 14.5 160 185 19 20
92 105 9.5 10.6 120 132 10 11 160 190 18 19
93 104 10 11 120 135 11.5 12.5 165 195 20 21
95 103 12 13 120 135 15 16 170 180 14.5 15.5
95 105 10 11 120 140 12 13 170 190 12 13
95 105 12 13 120 140 14.6 15.5 170 190 15 16
95 110 9 10 120 140 15 16 170 200 18 19
95 110 12 13 125 135 13.5 14.5 175 195 16 17
95 115 12 13 125 140 11 12 180 200 12 13
100 108 12 13 125 145 12 13 180 200 15 16
100 110 14 15 125 145 15 16 180 200 19 20
100 112 16 17 125 150 14 15 180 205 15 16
100 113 12.5 13.5 125 150 19 20 185 195 12 13
100 115 9 10 125 155 18 19 190 210 12 13
100 115 10 11 127 139.7 9.2 10 190 210 15 16
100 115 10.5 11.5 130 140 7.2 8 198 207.6 6.5 7.5
100 115 11 12 130 140 13.5 14.5 200 212 15 16
100 115 12 13 130 145 12 13 200 220 12 13
100 120 11.5 12.5 130 145 14 15 200 220 15 16
100 120 12 13 130 145 15 16 200 225 15 16
100 120 13.5 14.5 130 150 12 13 200 225 19 20
100 120 15 16 130 150 15 16 200 240 18 19
100 125 19 20 135 145 12 13 210 230 12 13
105 115 10 11 140 150 11.5 12.5 210 230 15 16
105 115 11.5 12.5 140 150 11.8 12.8 210 235 24.5 26
105 115 13.5 14.5 140 155 9.6 10.6 215 225 12 13
105 120 9.5 10.2 140 155 12 13 220 240 12 13
105 120 9.9 10.5 140 160 12 13 220 240 15 16
105 120 12 13 140 160 15 16 220 250 18 19
105 120 15 16 140 165 19 20 230 250 12 13
105 125 12 13 142 155 12 13 230 260 23.6 25
105 125 14.5 16 145 155 13.5 14.5 235 255 12 13
110 115 10 11 145 157.7 9 10 240 250 12 13
110 120 12 13 145 165 14.5 16 240 260 12 13
110 125 9.6 10.6 145 185 13.5 14.5 240 260 15 16
110 125 11 12 147 160 12 13 240 270 18 19
110 125 12 13 150 160 13.5 14.5 250 270 12 13
110 125 15 16 150 170 12 13 250 270 15 16
110 130 12 13 150 170 13.5 14.5 250 280 22 23
110 130 15 16 150 170 15 16 270 300 18 19
110 135 19 20 155 165 12 13 280 300 15 16
115 125 12 13 160 169 13.5 14.5 280 305 15 16
115 135 12 13 160 170 12 13 280 310 24 25
115 135 15 16 160 180 12 13 320 340 15 16

41
HRS MA35

piston rod seal with symmetrical seal lips which Profile width (mm) Lead-in chamfer C (mm)
are cut at an angle of less than 45°. There is a 4 2
second seal lip on the inner diameter. 5 2.5
7.5 4
Standard material
10 5
Polyurethane TPU92
12.5 6.5
15 7.5
Area of application
Hydraulics 20 10

reciprocating movements 25 10

Function The service life of the seal is lengthened if the


The HRS MA35 is a single function piston rod housing is provided with a metallic fitting on the
seal in the form of a compact U-ring. Its design side opposite the pressure. Within the operating
and the excellent material characteristics of parameters given above, depending on the
polyurethane guarantee effective sealing at pressure, a metallic wedge can be fitted
low and zero pressures as well as high pressure between the cylinder head and piston rod acc.
loads and a particularly long service life. Due to the following table:
to the second seal lip which provides even
greater effectivity of the sealing function, it is Pressure (MPa) Radial wedge G (mm)
particularly well-suited for positioning work in 5 0.6
hydraulics. 10 0.5
20 0.35
Media
30 0.3
Hydraulic oils acc. DIN 51524/51525,
40 0.25
lubricating oils, mineral oil based
lubricating fats, non-flammable Please also follow the general installation
hydraulic fluids HFA, HFB, HFC acc. instructions.
VDMA 24317
Remarks
Operational application limits In addition, we are able to supply other
Pressure (MPa/bar): 40/400 dimensions required. For operating conditions
Temperature (°C): –40 to +100 other than the standard applications, further
< +40 in HFA, HFB, HFC polyurethane materials are available.
Running speed (m/s): <0.5

Installation
The HRS MA35, from an inner diameter of 25 mm
and a thin profile, can always be installed in cut
housing. Due to the high tensile resistance of
polyurethane, it is necessary to use installation
tools for thick seals. With an inner diameter
of less than 25 mm, we recommend axially
accessible housing. To push the cylinder head
and seal over the piston rod without damaging
it, an lead-in chamfer C acc. to the following
table is required:

42
HRS MA35
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

6 14 5.8 6.3 28 34.2 5.2 6 42 50 6 7


6.35 14.3 6 7 28 36 5.8 6.3 42 52 8 9
8 14 5 6 28 36 6 7 45 53 5.8 6.3
8 14 5.8 6.3 28 38 5.8 6.3 45 53 8 9
8 15 5.8 6.3 28 38 7 8 45 55 5.8 6.3
8 16 5.8 6.3 30 38 5.8 6.3 45 55 7 8
10 16 4.8 5.4 30 38 6 7 45 55 7.5 8.5
10 18 5.8 6.3 30 38 7 8 45 55 10 11
12 19 5 6 30 38 8 9 45 57.7 9.5 10.5
12 19 5.8 6.3 30 40 6.5 7.5 46 54 8 9
12 20 5.8 6.3 30 40 10 11 48 58 10 11
12 23 6.5 7.5 32 40 5.8 6.3 48 60 6 7
14 20 4.8 5.3 32 40 6 7 49.5 65.3 10 11
14 21 5 6 32 40 6.7 7.7 50 58 8 9
14 22 5.8 6.3 32 40 8 9 50 60 7 8
15 21.5 4.2 5 32 41.5 7.8 8.9 50 60 7.5 8.5
15 23 6 7 32 42 5.8 6.3 50 60 9 10
15.4 25.5 6.5 7.5 32 42 7 8 50 60 10 11
16 24 5.8 6.3 32 42.5 8 9 50 60 12 13
16 24 6 7 32 47 10 11 50 62.7 9.5 10.5
18 25 5 6 35 43 5.8 6.3 50 65 10 11
18 26 5.8 6.3 35 43 6 7 50 70 13.5 14.5
18 26 6 7 35 43 8 9 55 63 8 9
18 26 8 9 35 45 10 11 55 65 7 8
18 28 5.8 6.3 35 45 12.5 13.5 55 65 7.5 8.5
19.5 27.5 8 9 35 50 10 11 55 65 10 11
20 26 5.2 6 36 44 5.8 6.3 55 65 12 13
20 28 5.8 6.3 36 44 6 7 56 64 8 9
20 30 4.5 5 36 44 8 9 56 66 6.5 7.5
20 30 7 8 37 47 7 8 56 71 11.5 12.5
22 28 4.5 5 38 50 8.5 9.5 60 68 6.3 7
22 28 5.8 6.3 40 48 5.4 6.4 60 68 8 9
22 29 5 6 40 48 5.8 6.3 60 68 11.5 12.5
22 30 5.8 6.3 40 48 6 7 60 70 7 8
22 30 6 7 40 48 6.3 7 60 70 7.5 8.5
25 33 5.8 6.3 40 48 8 9 60 70 11.5 12.5
25 33 6.5 7.5 40 49.5 9.5 10.5 60 71 8 9
25 33 7 8 40 50 7 8 60 72 9 10
25 35 5.8 6.3 40 50 10 11 60 75 10 11
25 35 7 8 40 55 10 11 61 69 8 9
25 35 8 9 40 60 10 11 63 71 8 9

43
HRS MA35
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

65 73 8 9 85 93 11.5 12.5 120 128 11.5 12.5


65 75 12.5 13.5 85 95 12 13 120 135 15 16
65 77 9 10 86 101 12 13 125 133 8 9
65 77.7 9.5 10.5 88 96 8 9 125 145 15 16
65 79.2 11.5 12.5 90 98 8 9 126 134 8 9
70 78 8 9 90 100 6.5 7.5 130 145 15 16
70 80 6.5 7.5 90 102 9 10 130 155 15 16
70 80 11.5 12.5 90 105 11.5 12.5 135 143 8 9
70 80 12 13 90 110 14 15 135 150 11.5 12.5
70 85 11.5 12.5 91 99 8 9 137 152 12 13
73 82.4 7 8 95 103 8 9 140 150 11.5 12.5
75 83 8 9 100 108 11.5 12.5 140 155 9.5 10.5
75 85 7 8 100 110 12 13 140 160 15 16
75 85 12 13 100 115 11.5 12.5 146 156 10 11
75 90 10.5 11.5 100 115 12 13 150 180 15 16
76 84 8 9 100 120 15 16 160 175 15 16
76.2 91.2 12 13 102 110 8 9 163 178 12 13
78 86 8 9 105 113 8 9 165.5 173 9 10
80 88 8 9 105 115 10.5 11.5 170 180 10 11
80 88 11.5 12.5 107 115 8 9 188 203 12 13
80 90 12 13 108 116 8 9 190 210 13.5 14.5
80 92 9 9 110 125 9.5 10.5 197 209 12 13
80 95 11 12 110 125 11.3 12 218 237 16 17
80 95 11.5 12.5 110 130 15 16 220 250 19.5 20.5
80 96 9.5 10.5 112 127 12 13 228 240 12 13
82.5 97.5 12 13 115 123 8 9 300 325 24 25
85 93 8 9 115 130 11.5 12.5

44
HPRS MA36

piston and piston rod seal with symmetrical seal Profile width (mm) Lead-in chamfer C (mm)
lips which are cut at an angle of less than 45°. 4 2
5 2.5
Standard material
7.5 4
Polyurethane TPU92
10 5
12.5 6.5
Area of application
15 7.5
Hydraulics
reciprocating movements 20 10
25 10

Function
The HPRS MA36 is a single function piston rod The service life of the seal is lengthened if the
seal in the form of a compact U-ring which, due housing is provided with a metallic fitting on the
to its symmetrical seal lips, can be applied as a side opposite the pressure. Within the operating
piston and piston rod seal. Its sealing function parameters given above, depending on the
is very effective as the seal lips are provided pressure, a metallic wedge can be fitted
with radial self-energising which is activated between the cylinder head and piston rod acc.
by the system pressure. Its compact design to the following table:
and the excellent material characteristics of
polyurethane guarantee effective sealing on Pressure (MPa) Radial wedge G (mm)
the one hand at low as well as high pressure 5 1.0
loads and, on the other, a particularly long 10 0.8
service life.
20 0.6
30 0.5
Media
40 0.4
Hydraulic oils acc. DIN 51524/51525,
lubricating oils, mineral oil based Please also follow the general installation
lubricating fats, non-flammable instructions.
hydraulic fluids HFA, HFB, HFC acc.
VDMA 24317 Remarks
In addition, we are able to supply other
Operational application limits dimensions required. For operating conditions
Pressure (MPa/bar): 40/400 other than the standard applications, further
Temperature (°C): –40 to +100 polyurethane materials are available.
< +40 in HFA, HFB, HFC
Running speed (m/s): < 0.5

Installation
The HPRS MA36, from an inner diameter of
25 mm and a thin profile, can always be
installed in cut housing. Due to the high tensile
resistance of polyurethane, it is necessary to
use installation tools for thick seals. With an inner
diameter of less than 25 mm, we recommend
axially accessible housing. To push the cylinder
head and seal over the piston rod or push the
piston rod with the seal into the cylinder rod
without damaging the seal, an lead-in chamfer
C acc. to the following table is required:

45
HPRS MA36
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

6 14 5.7 6.3 22 32 8 9 35 45 10 11
8 16 5.7 6.3 22 32 10 11 36 44 5.8 6.3
8 18 8 8.5 24 30 4.5 5 36 44 6 7
10 16 5 5.6 24 30 8 9 36 44 7 8
10 18 5.5 6.3 24 32 6 7 36 44 8 9
10 18 5.7 6.3 24 34 5.7 6.5 36 46 7 8
12 18 4.5 5 25 32 4 5 36 46 10 11
12 19 5 5.6 25 33 5.8 6.3 38 45 6 7
12 20 5.5 6.3 25 33 6 7 40 48 5.8 6.3
12 20 5.7 6.3 25 33 8 9 40 48 6 7
12 20 5.8 6.3 25 35 5 6 40 48 8 9
13 20 6 7 25 35 7 8 40 49.5 9.5 10.5
14 21 5 5.6 25 35 8 9 40 50 6 7
14 22 5.5 6.3 25 35 9 10 40 50 7 8
14 22 5.7 6.3 25 35 10 11 40 50 8 9
16 22 4 4.5 25 36 5 6 40 50 10 11
16 24 5.7 6.3 25 38 10 11 40 55 7.5 8.5
16 24 6 7 28 36 5.8 6.3 40 55 10 11
18 25 5 5.8 28 36 6 7 42 50 6 7
18 26 5.7 6.3 28 36 8 9 42 52 8.5 9.5
18 26 6 7 28 38 7 8 42 53 9 10
18 28 5.8 6.3 30 38 5.7 6.3 45 53 5.5 6.3
18 28 7 8 30 38 5.8 6.3 45 53 5.8 6.3
20 25 3 3.5 30 38 6 7 45 53 6 7
20 25 3.7 4.5 30 38 7 8 45 53 8 9
20 26 5 5.8 30 38 8 9 45 53 10 11
20 26 5.2 6 30 40 7 8 45 55 5.8 6.3
20 27 5.7 6.5 30 40 7.5 8.5 45 55 7 8
20 28 5.8 6.3 30 40 10 11 45 55 7.5 8.5
20 28 6 7 32 40 5.8 6.3 45 55 10 11
20 28 7 8 32 40 6 7 45 55 11 12
20 30 7.2 8 32 40 8 9 45 57.7 9.5 10.5
20 30 8 9 32 42 7 8 46 54 8 9
20 30 10 11 32 42 8 9 47 55 8 9
21 27 4.5 5 32 42 10 11 48 58 10 11
22 28 4.5 5.3 32 42.5 8 9 48 60 7 8
22 29 5 5.8 35 43 6 7 50 58 5.7 6.3
22 30 5.7 6.3 35 43 8 9 50 58 8 9
22 30 6 7 35 45 7 8 50 60 7 8
22 30 7 8 35 45 8 9 50 60 7.5 8.5
22 32 7 8 35 45 8.5 9.5 50 60 8 9

46
HPRS MA36
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

50 60 10 11 65 77 9 10 85 97 8.5 9.5
50 62 8 9 65 80 11.5 12.5 85 97 9 10
50 62 10 11 66 80 10 11 86 92 6 7
50 62.7 9.5 10.5 68 76 8 9 87 95 8 9
50 65 10 11 70 78 8 9 88 96 8 9
50 70 12 13 70 80 6.5 7.5 90 96 4.8 5.5
52 60 5.5 6.3 70 80 7 8 90 98 8 9
55 63 8 9 70 80 10 11 90 100 6.5 7.5
55 65 7.2 8 70 80 12 13 90 102 9 10
55 65 7.5 8.5 70 82 9 10 90 105 11.5 12.5
55 65 10 11 70 82 12 13 91 99 8 9
55 65 12 13 70 85 11.5 12.5 95 112 11.5 12.5
56 66 6.5 7.5 70 90 12 13 97 105 8 9
56 66 10 11 70 90 13.5 14.5 97 105 13 14
56 71 8.5 9.5 71 79 8 9 100 108 8 9
56 71 11.5 12.5 72 78 6 7 100 108 11.5 12.5
60 68 8 9 73 80 8 9 100 120 14.5 16
60 68 13 14 75 83 8 9 103 111 10 11
60 70 7 8 75 85 7.2 8 105 113 6.5 7.5
60 70 7.2 8 75 85 10 11 107 115 8 9
60 70 7.5 8.5 75 85 12 13 110 125 9.6 10.6
60 70 8 9 75 87 9 10 110 130 14.5 16
60 70 10 11 75 95 13.5 14.5 115 124 15 16
60 70 12 13 76 84 8 9 118 126 13 14
60 72 9 10 78 86 8 9 120 135 15 16
60 72 10 11 78 86 13 14 122 130 8 9
60 75 15 16.5 78 93 10.5 11.5 125 133 6.5 7.5
61 69 8 9 80 88 8 9 125 145 14.5 16
63 71 8 9 80 90 7.2 8 126 134 8 9
63 75 8.5 9.5 80 90 10 11 140 155 9.6 10.6
63 75 10 11 80 90 12 13 140 155.5 5.8 6.3
63 75 12 13 80 90 14 15 140 160 14.5 16
63 78 11.5 12.5 80 92 9 10 143 151 13 14
63 78 12.5 13.5 80 95 11.5 12.5 145 153 6.5 7.5
63 83 13.5 14.5 80 100 11.5 12.5 145 153 8 9
64 72 8 9 80 100 13.5 14.5 147 155 10 11
65 73 8 9 81 89 8 9 160 185 18.2 20
65 73 11.5 12.5 85 93 6.5 7.5 170 180 10 11
65 75 10 11 85 94 15 16 180 200 16 17.5
65 75 12 13 85 95 7 8

47
HRS MA39

piston rod seal with asymmetrical sealing lips Profile width (mm) Lead-in chamfer C (mm)
which are cut at an angle of less than 45°. There 4 2
is a second seal edge on the inner diameter. 5 2.5
7.5 4
Standard material
10 5
Polyurethane TPU92
12.5 6.5
15 7.5
Area of application
Hydraulics 20 10

reciprocating movements 25 10

extreme loads
If the housing is provided with a metallic
Function fitting on the side opposite the pressure, the
The HRS MA39 is a single function piston seal service life of the seal is lengthened. Within the
in the form of a U-ring. Its excellent suitability operating parameters given above, depending
for extreme loads is provided by the synergy on the pressure, a metallic wedge can be fitted
between the geometric of this seal and the between the cylinder pipe and piston acc. to
special material characteristics of polyurethane. the following table:
It guarantees effective sealing at low and zero
pressures as well as the most difficult operational Pressure (MPa) Radial wedge G (mm)
conditions which would overload conventional 5 0.6
elastomer or fabric seals. The second seal edge 10 0.5
supports the sealing function on the upward
20 0.35
stroke of the rod and also wipes remaining dirt
30 0.3
from the atmospheric side on the downward
40 0.25
stroke of the rod.
Please also follow the general installation
Media instructions.
Hydraulic oils acc. DIN 51524/51525,
lubricating oils, mineral oil based Remarks
lubricating fats, non-flammable In addition, we are able to supply other
hydraulic fluids HFA, HFB, HFC acc. dimensions required. For operating conditions
VDMA 24317. other than the standard applications, other
polyurthane materials are available.
Operational application limits
Pressure (MPa/bar): 40/400
Temperature (°C): -–40 to + 100
< + 40 in HFA; HFB; HFC
Running speed (m/s): = 0.5

Installation
The HRS MA39, from an inner diameter of 25
mm and a thin profile can always be installed
in cut housing. Due to the high strength of
polyurethane, it is necessary to use installation
tools for thick seals. With an inner diameter
of less than 25 mm, we recommend axially
accessible housing. To push the piston body
and seal over the piston rod without damaging
it, a lead-in chamfer C acc. to the following
table is required:

48
HRS MA39
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

4 12 6 7 20 26 4.8 5.3 30 40 7.3 8


6 13 5 5.5 20 28 4 4.5 30 40 8 9
6 14 5.5 6.5 20 28 5.5 6.5 30 40 10 11
6 14 5.7 6.3 20 30 6 7 30 42 8.5 9.5
6 16 6 7 20 30 7 8 30 45 10 11
8 16 5.5 6.5 20 30 7.3 8 30 45 11 12
8 16 5.7 6.3 20 30 8 9 30 50 12 13
8 16 8 9 20 30 10 11 32 40 6.7 7.5
8 18 8 9 20 35 10 11 32 40 8 9
9 16 5.7 6.3 20 40 4.5 5 32 41.5 7.9 8.9
10 16 4.5 5.3 22 30 6 7 32 42 7.3 8
10 17 5.7 6.3 22 30 7 8 32 42 10 11
10 18 5.5 6.5 22 32 6 7 32 45 10 11
10 18 5.7 6.3 22 32 7.3 8 32 47 10 11
10 20 4.5 5 22 32 8 9 32 47 11.5 12.5
10 20 7 8 22 35 10 11 35 43 7.2 8
10 20 8 9 23 35 10 11 35 45 6.5 7.5
12 20 5.5 6.5 25 32 10 11 35 45 7 8
12 20 5.7 6.3 25 33 5.5 6.5 35 45 8 9
12 20 8 9 25 33 6 7 35 45 10 11
12 22 7.3 8 25 33 6.5 7.3 35 50 10 11
12 22 8 9 25 33 7.3 8 36 44 6.3 7
14 22 5.5 6.5 25 33 10 11 36 46 7 8
14 22 5.7 6.3 25 35 6 7 36 46 7.3 8
14 24 7.3 8 25 35 7 8 36 46 7.5 8.5
14 24 8 9 25 35 7.3 8 36 46 8 9
15 25 8 9 25 35 8 9 36 46 10 11
15 26 7 8 25 35 10 11 36 51 10 11
15.4 25.5 6.5 7.4 25 38 10 11 36 56 12 13
16 24 5.5 6.5 25 40 10 11 37 47 8 9
16 24 5.8 6.3 25 45 12 13 37 47 10 11
16 26 7 8 28 36 7 8 38 55 10 11
16 26 7.3 8 28 36 7.3 8 40 48 5.7 6.3
16 26 8 9 28 36 8 9 40 49.5 9.5 10.5
18 25 5 5.5 28 38 7.3 8 40 50 7.3 8
18 26 5.5 6.5 28 38 7.5 8.5 40 50 10 11
18 26 6.3 7 28 38 8 9 40 55 10 11
18 26 8 9 28 38 10 11 40 55 11.5 12.5
18 28 7.3 8 28 43 10 11 40 60 12 13
18 28 8 9 28 43 11.5 12.5 42 50 11.5 12.5
19.5 27.5 8 9 30 40 6.5 7.5 42 52 10 11

49
HRS MA39
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

42 53 9 10 65 75 12 13 100 120 13 14
43 53 7.3 8 65 77.7 9.5 10.5 100 120 14.5 16
45 53 5.6 6.3 65 80 10 11 100 120 15 16
45 53 11.5 12.5 65 80 12 13 100 125 15 16
45 53 12 13 65 85 12 13 105 113 11.5 12.5
45 55 7 8 66 80 10 11 105 113 13.5 14.5
45 55 7.3 8 67 75 11.5 12.5 105 115 11.5 12.5
45 55 10 11 70 77.5 9 10 105 120 9.2 10
45 55 11.5 12.5 70 78 11.5 12.5 105 120 9.9 10.9
45 57.7 9.5 10.5 70 79 13 14 110 118 11.5 12.5
45 60 10 11 70 80 11.5 12.5 110 120 12 13
45 60 11.5 12.5 70 80 12 13 110 125 15 16
45 65 10 11 70 85 10 11 110 130 12 13
45 65 12 13 70 85 11.5 12.5 110 130 14.5 16
45 65 13 14 70 85 12 13 110 130 15 16
48 56 11.5 12.5 70 90 12 13 110 135 15 16
48 56 12 13 70 90 15 16 112 122 10 11
48 63 10 11 73 82.4 7 7.8 113 123 8.7 9.5
48 68 12 13 75 83 11.5 12.5 115 123 11.5 12.5
50 57 10 11 75 85 8.7 9.5 115 125 12 13
50 58 11.5 12.5 75 85 10 11 115 125 14 15
50 60 7 8 75 85 11.5 12.5 115 130 10 11
50 60 7.3 8 75 85 12 13 115 140 15 16
50 60 10 11 75 90 10 11 117 126 14 15
50 62 10 11 75 90 11 12 118 126 11.5 12.5
50 62.7 9.5 10.5 75 90 12 13 118 126 13 14
50 65 9.5 10.5 77 86 14 15 118 126 13.5 14.5
50 65 10 11 78 86 11.5 12.5 120 128 11.5 12.5
50 65 11 12 78 86 13.5 14.5 120 130 11.5 12.5
50 65 11.5 12.5 78 88 12 13 120 130 12 13
50 65 15.5 16.5 78 90 12 13 120 135 15 16
50 70 12 13 80 88 11.5 12.5 120 140 12 13
50 70 14 15 80 90 12 13 120 140 15 16
52 62 10 11 80 95 10 11 121 135 9 10
55 62.5 9 10 80 95 11.5 12.5 125 133 11.5 12.5
55 63 11.5 12.5 80 95 12 13 125 135 10 11
55 65 8.5 9.5 80 100 12 13 125 145 12 13
55 65 10 11 80 100 12.5 13.5 125 145 15 16
55 65 12 13 80 100 15 16 125 150 15 16
55 67 10 11 81 89 10.5 11.5 125 155 18 19
55 70 10 11 82.5 97.5 12 13 127 140 11.5 12.5
55 70 12 13 85 92.5 9 10 128 136 11.5 12.5
55 75 12 13 85 93 11.5 12.5 130 138 11.5 12.5
56 66 10 11 85 95 12 13 130 145 12 13
56 71 10 11 85 100 11.5 12.5 130 150 12 13
56 71 11.5 12.5 85 100 12 13 130 150 12.5 13.5
56 76 12 13 85 105 12 13 130 150 15 16
58 68 11.5 12.5 90 98 11.5 12.5 131 150 13 14
60 68 11.5 12.5 90 100 11.5 12.5 132 142 8.7 9.5
60 70 5.2 6 90 100 12 13 135 143 11.5 12.5
60 70 7.5 8.5 90 105 11.5 12.5 135 145 12 13
60 70 10 11 90 105 12 13 135 150 11.5 12.5
60 70 11.5 12.5 90 110 12 13 135 150 15 16
60 70 12 13 92 107 11.4 12.5 137 146 14 15
60 75 10 11 93 101 11.5 12.5 140 148 11.5 12.5
60 75 11.5 12.5 95 103 11.5 12.5 140 150 11.5 12.5
60 75 12 13 95 105 8.7 9.5 140 160 12 13
60 75 15.5 16.5 95 105 12 13 140 160 15 16
60 80 12 13 95 115 12 13 140 165 15 16
63 71 8 9 97 105 11.5 12.5 140 170 18 19
63 73 12 13 97 105 13 14 141 151 12 13
63 75 8.5 9.5 97 105 13.5 14.5 143 151 11.5 12.5
63 75 10 11 97 106 14 15 143 151 13 14
63 78 10 11 99 109 12 13 143 151 13.5 14.5
63 78 11.5 12.5 100 108 11.5 12.5 145 155 12 13
63 83 12 13 100 110 8 9 145 160 12 13
63 83 13.5 14.5 100 110 10 11 148 160 12 13
65 73 11.5 12.5 100 110 11.5 12.5 150 170 14.5 15.5
65 75 10 11 100 115 12 13 150 170 15 16
65 75 11.5 12.5 100 120 12 13 150 180 18 19

50
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L

152 160 11.5 12.5 170 180 12 13 200 225 19 20


152 162 10 11 170 190 15 16 200 230 18 19
152 171 11.5 12.5 170 200 18 19 205 220 12.5 13.5
152.5 160.5 14 15 171 179 11.5 12.5 209 228 13 14
155 163 11.5 12.5 171 179 13 14 210 230 15 16
155 165 12 13 175 185 12 13 210 240 18 19
160 168 11.5 12.5 177 205 19 20 212 220 13.5 14.5
160 170 11.5 12.5 180 188 13.5 14.5 220 250 18 19
160 170 12 13 180 190 10 11 232 246 12 13
160 180 15 16 180 195 12.5 13.5 240 260 15 16
160 185 15 16 180 200 15 16 250 270 15 16
160 185 18.2 20 180 205 15 16 270 300 18 19
160 190 18 19 180 205 19 20 280 300 15 16
162 172 12 13 180 210 18 19 280 310 18 19
165 184 13 14 185 193 11.5 12.5 320 350 20 21
165 190 17 18 185 195 12 13 360 390 20 21
167 176 11.5 12.5 200 208 11.5 12.5
170 178 11.5 12.5 200 220 15 16

51
HRS MA41

piston rod seal with asymmetrical seal lips which To push the cylinder head and seal over the
are cut at an angle of less than 45°. There is a piston rod without damaging it, an lead-
second seal edge on the inner diameter and in chamfer C ace. to the following table is
the seal unit has an integrated support ring. required:

Standard material Profile width (mm) Lead-in chamfer C (mm)


Polyurethane TPU92 4 2
Polyoxymethylene POM 5 2.5
7.5 4
Area of application
10 5
Hydraulics
12.5 6.5
reciprocating movements
15 7.5
extreme loads
20 10

Function 25 10

The HRS MA41 is a single function piston rod seal


in the form of a U-ring. Its excellent suitability for The service life of the seal is lengthened if the
extreme loads, which is for example required housing is provided with a metallic fitting on the
for application in the working cylinders of side opposite the pressure. Within the operating
heavy earth-moving machines, is provided parameters given above, depending on the
by the synergy between the geometric of this pressure, a metallic wedge can be fitted
seal and the special material characteristics of between the cylinder head and piston rod ace.
polyurethane. It guarantees effective sealing to the following table:
at low and zero pressures as well as the most
difficult operational conditions which would Pressure (MPa) Radial wedge G (mm)
overload conventional elastomer or fabric seals. 5 1.0
The second seal lip supports the sealing function 10 0.8
on the upward stroke of the rod and also wipes
20 0.6
remaining dirt from the atmospheric side on the
30 0.5
downward stroke of the rod. The semi-active
40 0.4
support ring on the inner diameter protects
against fission extrusion. Please also follow the general installation
instructions.
Media
Hydraulic oils ace. DIN 51524/51525, lubricating Remarks
oils, mineral oil based lubricating fats, non- In addition, we are able to supply other
flammable hydraulic fluids HFA, HFB, HFC ace. dimensions required. For operating conditions
VDMA24317 other than the standard applications, further
polyurethane materials are available.
Operational application limits
Pressure (MPa/bar): 40/400
Temperature (°C): -40 to +100
< +40 in HFA, HFB, HFC
Running speed (m/s): <0.5

Installation
The HRS MA41, from an inner diameter of 25 mm
and a thin profile, can always be installed in cut
housing. Due to the high tensile resistance of
polyurethane, it is necessary to use installation
tools for thick seals. With an inner diameter
of less than 25 mm, we recommend axially
accessible housing.

52
HRS MA41
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H L Ø dN ØDN H L Ø dN ØDN H L
Sizes
metric

30 40 8 9 60 69 10 11 95 105 12 13
35 45 8 9 60 70 10 11 97 105 13 14
40 50 10 11 60 80 12 13 100 120 13,5 14,5
40 55 10 11 63 83 12 13 105 125 12 13
42 51 10 11 70 80 7,2 8 115 125 12 13
42 52 13 14 70 80 10 11 118 126 13 14
50 59 10 11 70 85 11,5 12,5 120 140 12 13
50 60 7,2 8 75 85 12 13 125 145 12 13
50 60 10 11 78 86 13 14 135 145 12 13
50 65 10 11 80 90 12 13 143 151 13 14
50 70 12 13 80 95 11,5 12,5 160 170 12 13
60 68 13 14 90 100 12 13 171 179 13 14

53
HRS MA43

is a PTFE U-ring seal which is provided with a Operational application limits


steel V spring. Pressure (MPa/bar): 35/350
Temperature (°C): -150 to +250
Standard material Running speed (m/s): up to 15
U-ring: PTFE/carbon compound
V spring: non-corrosive, acid resistant steel Installation
1.4310 We generally recommend split seal housing. In
a limited range, half-open or closed housing
Area of application is also possible. Please also follow the general
Diverse applications in all branches of general installation instructions.
mechanical and apparatus engineering,
hydraulics and pneumatics, chemical Remarks
and processing technology, reciprocating For operational conditions other than the
movements. standard applications, further PTFE compounds
and V springs made of ELGILOY® are
Function available. The use of PTFE compounds in the
The HRS MA43 is a single acting, internal sealing pharmaceutical and foodstuffs industries is
U-ring with sealing lips of varying design. completely harmless. However, in this case,
These achieve optimal sealing strength and the spring housing of the seal should be filled
reduces friction. This results in the seal having completely with a flexible silicone casting
an exceptionally good service life. The metal compound so that a smooth surface is formed.
spring permanently activates the sealing lips Please mention this application when placing
which guarantees zero leakage even in an your orders.
unpressurized state.

Media
All types of hydraulic oils, hot air, steam, most
chemicals.

54
HRS MA43
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H Ø dN ØDN H Ø dN ØDN H
Sizes
metric

3 5.9 2.4 60 69.4 7.1 210 222.2 9.5


4 6.9 2.4 63 72.4 7.1 215 227.2 9.5
5 7.9 2.4 65 74.4 7.1 220 232.2 9.5
6 8.9 2.4 70 79.4 7.1 230 242.2 9.5
8 10.9 2.4 75 84.4 7.1 240 252.2 9.5
10 14.5 3.6 80 89.4 7.1 250 262.2 9.5
12 16.5 3.6 85 94.4 7.1 254 266.2 9.5
14 18.5 3.6 90 99.4 7.1 280 292.2 9.5
15 19.5 3.6 95 104.4 7.1 300 312.2 9.5
16 20.5 3.6 100 109.4 7.1 310 322.2 9.5
18 22.5 3.6 103 112.4 7.1 320 332.2 9.5
20 26.2 4.8 105 114.4 7.1 330 342.2 9.5
22 28.2 4.8 110 119.4 7.1 350 362.2 9.5
25 31.2 4.8 115 124.4 7.1 360 372.2 9.5
28 34.2 4.8 120 132.2 9.5 400 412.2 9.5
30 36.2 4.8 125 137.2 9.5 410 422.2 9.5
32 38.2 4.8 130 142.2 9.5 450 462.2 9.5
35 41.2 4.8 135 147.2 9.5 460 472.2 9.5
36 42.2 4.8 140 152.2 9.5 480 492.2 9.5
40 49.4 7.1 150 162.2 9.5 490 502.2 9.5
42 51.4 7.1 155 167.2 9.5 500 512.2 9.5
45 54.4 7.1 160 172.2 9.5 530 542.2 9.5
48 57.4 7.1 165 177.2 9.5 550 562.2 9.5
50 59.4 7.1 170 182.2 9.5 580 592.2 9.5
52 61.4 7.1 180 192.2 9.5 600 612.2 9.5
53 62.4 7.1 190 202.2 9.5 620 632.2 9.5
55 64.4 7.1 195 207.2 9.5 630 642.2 9.5
56 65.4 7.1 200 212.2 9.5 650 662.2 9.5

Installation dimensions (mm) Series No.


000 001 002 003 004

Rod ød h9
Standard range 3-9,9 10-19,9 20-39,9 40-119,9 120-999,9
Non-standard range 3-40 6-200 10-400 20-700 35-999,9

øD H9 d +2,9 d +4,5 d +6,2 d +9,4 d +12,2

L +0,2 2,4 3,6 4,8 7,1 9,5

R max 0,4 0,4 0,6 0,8 0,8

Radial gap G
1 MPa 0,2 0,2 0,4 0,5 0,6
10 MPa 0,1 0,15 0,2 0,25 0,3
20 MPa 0,1 0,1 0,15 0,2 0,25
35 MPa 0,08 0,1 0,12 0,15 0,15

55
HPS MA44

piston seal with a V-spring as an energising Media


element All types of hydraulic oils, hot air, steam and
most chemicals
Standard material
PTFE/carbon compound non-corrosive, acid- Operational application limits
resistant steel 1.4310 Pressure (MPa/bar): 35/350 Temperature (°C):
-150 to +250 Running speed (m/s): up to 15
Area of application
All areas of general mechanical Installation
and apparatus engineering, We generally recommend split seal housing. In
chemical engineering and process a limited range, half-open or closed housing
technology, is also possible. Please also follow the general
hydraulics and pneumatics, installation instructions.
reciprocating movements
Remarks
Function For operating conditions other than the
The HPS MA44 is a single function piston seal standard applications, further PTFE compounds
in the form of a U-ring with seal lips of varying and V springs made of ELGILOY® are
design. These achieve optimal sealing strength available. The use of PTFE compounds in the
and reduce friction. This results in the seal pharmaceutical and foodstuffs industries is
having an exceptionally long service life. The completely harmless. However, in this case,
metal spring permanently activates the seal the spring housing of the seal should be filled
lips which guarantees zero leakage even completely with a flexible silicone casting
in an unpressurized state. As a result of the compound so that a smooth surface is formed.
exceptionally positive material characteristics Please mention this application when placing
of PTFE, there is no stick slip movement of your orders.
the piston at differing stroke speeds, even
during a single cycle and with extremely slight
movements. Total lack of leakage with regard
to media viscosity and its hydrodynamic
dragging behaviour as well as dependable
functioning in high temperature, speed and
pressure areas characterise these seals. They
are used as piston seals in hydraulics and
pneumatics.

56
HPS MA44
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN H Ø dN ØDN H Ø dN ØDN H
Sizes
metric

8 5,1 2,4 60 50,6 7,1 185 172,8 9,5


10 7,1 2,4 63 53,6 7,1 190 177,8 9,5
12 9,1 2,4 65 55,6 7,1 200 187,8 9,5
14 9,5 3,6 68 58,6 7,1 210 197,8 9,5
15 10,5 3,6 70 60,6 7,1 220 207,8 9,5
16 11,5 3,6 73 63,6 7,1 230 217,8 9,5
17 12,5 3,6 75 65,6 7,1 240 227,8 9,5
18 13,5 3,6 80 70,6 7,1 250 237,8 9,5
20 15,5 3,6 85 75,6 7,1 254 241,8 9,5
22 17,5 3,6 90 80,6 7,1 280 267,8 9,5
25 18,8 4,8 95 85,6 7,1 300 287,8 9,5
28 21,8 4,8 100 90,6 7,1 310 297,8 9,5
30 23,8 4,8 110 100,6 7,1 320 307,8 9,5
32 25,8 4,8 115 105,6 7,1 350 337,8 9,5
35 28,8 4,8 120 110,6 7,1 380 367,8 9,5
40 33,8 4,8 125 112,8 9,5 400 387,8 9,5
42 35,8 4,8 130 117,8 9,5 420 407,8 9,5
45 38,8 4,8 135 122,8 9,5 440 427,8 9,5
48 38,6 7,1 140 127,8 9,5 450 437,8 9,5
50 40,6 7,1 145 132,8 9,5 480 467,8 9,5
52 42,6 7,1 150 137,8 9,5 500 487,8 9,5
54 44,6 7,1 160 147,8 9,5 520 507,8 9,5
55 45,6 7,1 170 157,8 9,5
56 46,6 7,1 180 167,8 9,5

Installation dimensions (mm) Series No.


000 001 002 003 004

Cylinder øD H9
Standard range 6-13,9 14-24,9 25-45,9 46-124,9 125-999,9
Non-standard range 6-40 10-200 16-400 28-700 45-999,9

øD h9 D-2,9 D-4,5 D-6,2 D-9,4 D-12,2

L +0,2 2,4 3,6 4,8 7,1 9,5

R max 0,4 0,4 0,6 0,8 0,8

Radial gap G
2 MPa 0,2 0,2 0,4 0,5 0,6
10 MPa 0,1 0,15 0,2 0,25 0,3
20 MPa 0,1 0,1 0,15 0,2 0,25
35 MPa 0,08 0,1 0,12 0,15 0,15

57
Wipers Wipers are essential elements of hydraulic
and pneumatic cylinders. Their function is to
remove any dirt collected on the extending
piston rod so that no foreign particles can
enter the cylinder or the system. The pressure
medium would otherwise be polluted which
would lead to destruction of the seal and
to the moving surfaces and all other parts
being damaged.

Materials, design and arrangement must be


matched to the most diverse requirements.
Whether a wiper consists of pure Elastomer
or requires a steel cage around its outer
diameter which can either be open or
covered by the elastomer, or whether a
double wiper is necessary, is dependent
on the sealing concept, the rod speed, the
stroke frequency and many other factors.

The wipers to be selected for large cylinders


used in very heavy mobile applications
with a high dirt load have quite different
geometrics and materials to the ones for
small hydraulic cylinders for internal areas
where they only have light loads to move.
Wipers in pneumatic cylinders again require
different materials and designs.

The careful balancing of the necessities of


the task and the wiper’s possibilities has an
important effect on selection and this in turn
on the function and operating security of
the system.

58
Materials NBR acrylnitrile-butadiene rubber Polyurethane
NBR is the most commonly used material in Polyurethane is one of the group of elastic
all areas of seal technology due to its good thermoplastic materials which have
physical and mechanical characteristics established themselves in seal technology
and its exceptional processing abilities. It since many years due to their physical
is used at hardnesses between 40 and 90 characteristics and efficient processing
Shore A. features. A hardness range of between 65
and 98 Shore A is used.
NBR for wipers
With few exceptions, NBR90 is used for Among the most important material
wipers. This type of elastomer combines the characteristics are its very high tensile
characteristics required for wipers; rigidity, strength, good wear resistance, good
hardness and abrasion resistance. flexibility at a temperature range from
-40°C to +100°C, but also good weathering
NBR is resistant to most hydraulic media and resistance against ozone. The oils and
other mineral oil based lubricants and also lubricants used in hydraulics have a
to their emulsions with water. minimal influence on the physical values of
polyurethane.
However, NBR materials have only moderate
resistance against weathering and Polyurethane TPU92
ozone influences if they are not specially TPU92, with very few exceptions, is
developed for these applications. Standard the polyurethane used for wipers. The
resistance of the elastomer is generally characteristics of this type of material unite
sufficient as with typical application in the appropriate stiffness, hardness and, in
hydraulics the surfaces are moistened with particular, abrasion resistance necessary
oil or fat. These media form a stable surface for wipers. The injection moulding process
protective layer and minimize the intensity of applied in most cases for production requires
ozone influence. complex machinery and moulding tools and
for this reason is most appropriate for large
In general, the NBR90 standard compound scale production.
can be applied at temperatures from
-30°C to + 100°C. With wipers, below- Polyurethane wipers are also often bonded
zero temperatures as low as -40°C are still with metal. In a tried and tested process, the
acceptable. pre-processed metal parts are firmly bonded
with the polyurethane to form a single unit.
NBR is processed into wipers using moulding
tools and stabilized in different processes Polyurethane TPU98
and depending of its type vulcanised to This quality of polyurethane is only applied
metal cages. For this purpose, the metal for wipers manufactured in a laithed
is pretreated and firmly bonded with the process. On the one hand, its exceptional
elastomer in a tried and tested process to hardness simplifies the processing and, on
form a single unit. the other hand, gives the wipers such high
durability that they are extremely well-suited
NBR for O-rings to use with strongly adherent dirt on rods as
NBR O-rings in a hardness of 70 Shore A are well as frost and ice.
used as energizing elements in two part
wiper types. This standard quality is best
suited for this purpose and is one of the most
commonly used in the seal market.

It has the advantage of tremendous


applicability. However, the composite wipers
are subject to the usual constraints of the
chemical resistance and temperature limits
of NBR. The temperature range for NBR 70
material is -30°C to +100°C.

59
Polyamide PTFE with different compounds has proved
Polyamide is a thermoplastic material and to be excellent material for wipers. In
is distinguished by its particularly high wear particular, PTFE/bronze with a 40% bronze
resistance, rigidity, hardness and good content; the wear resistance of the material,
gliding characteristics. In addition, it has which already has excellent gliding
good resistance to most hydraulic media characteristics, is improved. In addition, this
and other mineral oil based lubricants. reduces deformation under pressure.

As wiper material, polyamide can either PTFE material is not very elastic on its
be used pure or can be compounded with own. For this reason, the activity of
different fillers for special applications. The wipers is compensated with an elastic
wipers made of this material are normally energizing element. Standard O-rings
produced by injection moulding and offer made of elastomer NBR 70 are used for this
a real alternative to the most varied metal application. Naturally, O-rings made of other
wipers. The high wear resistance of these elastomers are available for non-standard
wipers provides them with a particularly long applications.
service life and they are highly suitable for
heavy duty applications, including use at PTFE is characterised by its almost universal
low temperatures with ice formation. chemical resistance and ability to remain
stable within a very wide temperature
Should particular geometrics be required, range. Its application with hydraulic oils and
the polyamide wipers can also be produced mineral oil based lubricants and their water
in a laithed process. emulsions as well as application temperature
limits are, however, restricted by the
Wipers made of polyamide are generally combination of elastomer components in
recommended for use at a temperature the wipers.
range of between -40°C and +100°C.
FKM fluorelastomer
Polytetraflourethylene (PTFE) The FKM rubber is distinguished by its
The PTFE material has numerous positive excellent chemical and temperature
characteristics which have become resistance (from -20°C to +200°C). It
indispensable in seal technology and are therefore plays an important part as a wiper
ingeniously concentrated in one single material outside the standard.
material. In particular, we would like to point
out the characteristics which are essential Due to the above characteristics it is
for its application as wiper material: essential to use FKM when extremely high
temperatures occur in the hydraulic cylinder
PTFE is distinguished by exceptional stiffness and highly flammable type D liquids have to
and very good gliding characteristics. Due be used.
to its extremely low surface energy, it has
a very low coefficient of friction (values of FKM is generally used in 90 Shore A and
under 0.02 are known) and exceptional non- can also be processed in combination with
bonding, non-wettable contact surfaces. In metal.
addition, its extreme hydrophobia must be
mentioned; PTFE is totally water-repellent.

Apart from this, it is immune to attack by


oxygen, ozone or ultra-violet rays and is
therefore absolutely resistant to weathering.

PTFE does not contain any extractable


media which could drift off and adversely
affect adjacent materials. It is therefore
physiologically completely harmless
in contact with foodstuffs and also
particularly well-suited for applications in the
pharmaceutical and medicinal fields.

60
Notes for Notwithstanding the strength of the
material, particular care is required with the
installation
installation of wipers to prevent damage
which would lead to inefficiency of the
wipers before initial operation.

■■ When using double wipers, depending


on the subsequent seal arrangement,
a leakage hole may be necessary,
through which the retained oil is
returned to the system.

■■ It is imperative to have lead-in chamfers


in the installation area with different
wipers. You will find the recommended
lengths and angles in the installation
dimension information for each wiper.

■■ Sharp edges must be deburred and radii


and chamfering provided according to
the installation dimension information.
Tips of screws and sharp edges must be
covered.

■■ Dust, dirt, chips and other foreign


particles must be carefully removed.

■■ Installation areas and wipers must be


greased or oiled before installation,
giving consideration to compatibility
with the medium.

■■ Any tools used for installation, e.g.


mandrels, should be made of soft
material and not have any sharp edges.

61
Overview of
Wipers Ref. Temp. Speed Materials Dimensions Page
(°C) (m/s) metr. inch

Design

WR A40 Wiper -40 4 NBR90 ■ ■ 64


+100

WR A41 Wiper -40 4 NBR90 ■ 67


+100

WR AD51 Double -40 1 NBR90 ■ 69


Wiper +100

WR AD53 Double -40 1 NBR90 ■ ■ 71


Wiper +100

WR AM43 Wiper -40 1 NBR90/ ■ 73


+100 steel DIN 1624

WR AM45 Wiper -40 1 NBR90/ ■ 76


+100 steel DIN 1624

WR A05 Wiper -­30 1 TPU95 ■ ASK


+100

WR A42 Wiper -40 2 TPU92 ■ 75


+100

WR A47 Wiper -40 2 TPU92 ■ 80


+100

WR AD48 Double -40 1 TPU92 ■ 82


Wiper +100

WR AM44 Wiper -40 2 TPU92/ ■ ■ 84


+100 steel DIN 1624

62
Overview of
Wipers Ref. Temp. Speed Materials Dimensions Page
(°C) (m/s) metr. inch

Design

WR AM54 Wiper -40 1 AU92/ ■ ■ 87


+100 steel DIN 1624

WR ADM55 Double -40 1 TPU92/ ■ 89


Wiper +100 steel DIN 1624

WR AD70 Double -30 2 TPU98/ ■ 91


Wiper +100 NBR70

WR AD71 Double -30 2 TPU98/ ■ 93


Wiper +100 NBR70

WR A11 Wipers ­-40 4 TPE55 ■ ■ ASK


120

WR A46 Wiper ­-40 4 PA ■ ■ ASK


100

WR A80 Wiper -30 15 PTFE/bronze ■ 95


+100 NBR70

WR AD60 Double -30 15 PTFE/bronze ■ 97


Wiper +100 NBR70

WR AD61 Double -30 15 PTFE/bronze ■ 99


Wiper +100 NBR70

63
WR A40

Wiper with a sharply-defined lip edge Installation


The wiper is built in to a semi-closed axial
Standard material groove. The recess on the atmospheric side of
Elastomer NBR90 the groove ensures good axial security in the
housing.
Area of application The R radius which is dependent on the height
Hydraulic and pneumatic systems, reciprocal of the wiper, is selected as follows:
movements, medium dirt load
H (mm) ≤12 16 18
Function R (mm) 1 1.5 3
The WR A40 is a single function wiper.
It is pressed against the descending piston rod Please also follow the general installation
wiping the dirt from the surface of the rod. instructions.
The seals, their associated elements and the
medium are protected from dirt. Pads on the Remarks
inner diameter support the correct functional In addition, we are able to supply other
fit by preventing additional pressure build-up in dimensions required. For operational
the back area which could press the wiper out conditions outside the standard applications,
of its housing. other elastomers, such as FKM for higher
temperatures, are available.
Media
Hydraulic oils acc. to DIN 51524/ 51525, The pads described in the function paragraph
lubricating oils, other mineral oil based fluids are not always taken into account outside the
and HFA, HFB, HFC highly non-flammable standard area in terms of tooling.
hydraulic fluids acc. to VDMA 24317

Operational application limits


Temperature (°C): -40 to + 100
Running speed (m/s): up to 4

64
WR A40
Dimensions in mm Dimensions in mm
Ø dN ØDN h H ØD1 ØD2 L Ø dN ØDN h H ØD1 ØD2 L
Sizes
metric

10 14 2 3 14.2 12.2 2.3 56 66 5 7 66.6 59 5.3


12 18 2.6 3.5 18.2 14.4 2.8 58 68 5 7 68.6 61 5.3
12 18 3.4 5.5 18.6 15 3.8 60 68 5 7 68.6 63 5.3
13 19 3.4 5.5 19.6 16 3.8 60 70 5 7 70.6 63 5.3
14 20 3.4 5.5 20.6 17 3.8 60 72 5 7 72.6 63 5.3
14 21 3.4 5.5 21.6 17 3.8 62 70 5 7 70.6 65 5.3
15 21 3.4 5.5 21.6 18 3.8 63 71 5 7 71.6 66 5.3
16 22 3.4 5.5 22.6 19 3.8 63 73 5 7 73.6 66 5.3
16 24 4 6 24.2 19 4.3 63 75 6 9 75.2 69 6.3
16 24 5 7 24.6 19 5.3 64 72 5 7 72.6 67 5.3
17 23 3.4 5.5 23.6 20 3.8 65 73 5 7 73.6 68 5.3
17 24 3.5 5.5 24.6 20 3.8 65 75 5 7 75.6 68 5.3
18 24 3.4 5.5 24.6 21 3.8 65 77 6 9 77.2 71 6.3
18 26 5 7 26.6 21 5.3 65 77 7 12 77.2 71 7.1
18 30 4 7 30.2 21 4.3 70 78 5 7 78.6 73 5.3
18 30 5 7 30.6 21 5.3 70 80 5 7 80.6 73 5.3
19 28 5 7 28.6 22 5.3 70 80 7 12 80.2 76 7.1
20 28 5 7 28.6 23 5.3 70 82 7 12 82.2 76 7.1
22 29.5 5 7 30.1 25 5.3 72 80 5 7 80.6 75 5.3
22 30 5 7 30.6 25 5.3 73 81 5 7 81.6 76 5.3
24 32 5 7 32.6 27 5.3 75 83 5 7 83.6 78 5.3
25 33 5 7 33.6 28 5.3 75 85 5 7 85.6 78 5.3
26 33 4 7 33.2 29 4.3 75 87 5 7 87.6 78 5.3
26 34 5 7 34.6 29 5.3 75 87 7 12 87.2 81 7.1
27 35 5 7 35.6 30 5.3 75 88 5 7 88.6 78 5.3
28 36 5 7 36.6 31 5.3 76.5 88 7 12 88.2 82.5 7.1
28 38 5 7 38.3 30.2 5.3 78 92 7 12 92.2 84 7.1
29.5 40 7 12 40.2 35.5 7.1 80 88 5 7 88.6 83 5.3
30 38 5 7 38.6 33 5.3 80 90 7 12 90.2 86 7.1
30 39 5 7 39.4 32 5.3 80 92 7 12 92.2 86 7.1
30 42 6 9 42.6 36 6.3 80 96 8 12 96.2 86 8.2
30 42 7 12 42.2 36 7.1 83 91 5 7 91.6 86 5.3
30 45 5 8 45.3 35.5 5.3 83 98 5 7 98.6 86 5.3
32 40 5 7 40.6 35 5.3 84 91.7 5 7 92.3 87 5.3
33 41 5 7 41.6 36 5.3 85 93 5 7 93.6 88 5.3
33 42 5 7 42.6 36 5.3 85 97 7 12 97.2 91 7.1
35 43 5 7 43.6 38 5.3 85 101 5 7 101.6
88 5.3
35 47 4 7 47.2 38 4.3 87 95 4 7 95.2 90 4.3
35 47 5 7 47.6 38 5.3 88 100 7 12 100.2
94 7.1
36 44 5 7 44.6 39 5.3 90 100 7 12 100.2
96 7.1
36 48 5 7 48.2 39.4 5.3 90 102 7 12 102.2
96 7.1
36 48 6 9 48.2 42 6.3 92 100 5 7 100.6
95 5.3
38 46 5 7 46.6 41 5.3 92 104 7 12 104.2
98 7.1
40 48 4 7 48.6 43 5.3 95 103 5 7 103.6
98 5.3
40 48 5 7 48.6 43 5.3 95 105 7 12 105.2 101 7.1
40 50 5 7 50.6 43 5.3 95 107 7 12 107.2 101 7.1
40 52 5 8 52.2 46 7.2 97 111 7 12 111.2 103 7.1
40 52 6 9 52.2 46 6.3 100 108 5 7 108.6 103 5.3
42 50 5 7 50.6 45 5.3 100 112 7 12 112.2 106 7.1
42 54 6 9 54.2 48 6.3 100 116 8 12 116.2 106 8.2
45 53 5 7 53.6 48 5.3 101 110.8 5 7 111.4 104 5.3
45 55 5 7 55.6 48 5.3 103 115 7 12 115.2 109 7.1
45 57 5 7 57.6 48 5.3 104 116 7 12 116.2 110 7.1
45 57 6 9 57.2 51 6.3 105 113 5 7 113.6 108 5.3
46 54 5 7 54.6 49 5.3 105 116 7 12 116.2 111 7.1
48 56 5 7 56.6 51 5.3 105 117 7 12 117.2 111 7.1
50 58 5 7 58.6 53 5.3 105 120 7 12 120.2 111 7.1
50 60 5 7 60.6 53 5.3 110 118 5 7 118.6 113 5.3
50 62 5 7 62.6 53 5.3 110 122 7 12 122.2 116 7.1
50 62 6 9 62.2 56 6.3 112 120 5 7 120.6 115 5.3
50 65 7.5 12 68.8 57.2 7.7 114 125 7 12 125.2 120 7.1
53 61 5 7 61.6 56 5.3 115 123 5 7 123.6 118 5.3
55 63 5 7 63.6 58 5.3 115 125 5 7 125.6 118 5.3
55 65 5 7 65.6 58 5.3 115 127 7 12 127.2 121 7.1
55 67 6 9 67.2 61 6.3 116 128 7 12 128.2 122 7.1
55 67 7 12 67.2 61 7.2 116 130 7 12 130.2 122 7.1
56 64 5 7 64.6 59 5.3 118 128 5 7 128.6 121 5.3

65
WR A40
Dimensions in mm Dimensions in mm
Ø dN ØDN h H ØD1 ØD2 L Ø dN ØDN h H ØD1 ØD2 L
Sizes
metric

118 130 7 12 130.2 124 7.1 160 172 7 12 172.2 166 7.2
120 128 5 7 128.6 123 5.3 160 172 7.5 12 172.2 166 7.6
120 130 5 7 130.6 123 5.3 160 175 10 16 175.6 167.6 10.2
120 132 7 12 132.2 126 7.1 165 173 5 7 173.6 168 5.3
121 130.6 5 7 131.2 124 5.3 170 180 5 7 180.6 173 5.3
125 133 5 7 133.6 128 5.3 170 182 7 12 182.2 176 7.1
125 137 7 12 137.2 131 7.1 170 185 10 16 182.6 177.6 10.2
125 137 7.5 12 137.2 131 7.6 171 181 5 7 181.6 174 5.3
125 140 10 16 140 132.6 10.2 171 183 7 12 183.2 177 7.1
125 141 8 12 141.2 131 8.2 175 183 5 7 183.6 178 5.3
127 135 5 7 135.6 130 5.3 175 189 7 12 189.2 181 7.1
127 136.5 5 7 137.1 130 5.3 180 195 10 16 195.6 187.6 10.2
130 142 7 12 142.2 136 7.1 180 200 10 18 200 190 10.2
130 145 10 16 145.6 137.6 10.2 185 193 5 7 193.6 188 5.3
135 147 7 12 147.2 141 7.1 185 197 7 12 197.2 191 7.1
135 149 7 12 149.2 141 7.1 185 200 10 16 200.6 192.6 10.2
140 148 5 7 148.6 143 5.3 190 198 5 7 198.6 193 5.3
140 149 5 7 149.6 143 5.3 190 205 10 16 205.6 197.6 10.2
140 150 5 7 150.6 143 5.3 190 210 10 18 210 200 10.2
140 152 7 12 152.2 146 7.1 195 210 10 16 210.6 202.6 10.2
140 155 10 16 155.6 147.6 10.2 196 210 7 12 210.2 202 7.1
143 151 5 7 151.6 146 5.3 200 215 10 16 215 210 10.2
143 153 5 7 153.6 146 5.3 200 220 10 18 220 210 10.2
145 153 5 7 153.6 148 5.3 210 220 5 7 220.6 213 5.3
145 157 7 12 157.2 151 7.1 210 225 10 16 225 217.6 10.2
145 160 9 16 160.6 152.6 9.1 210 230 10 18 230 220 10.2
145 160 10 16 160.6 152.6 10.2 220 235 10 18 235 230 10.2
146 158 7 12 158.2 152 7.1 220 240 10 18 240 230 10.2
150 162 6 12 162.2 156 6.3 230 250 10 18 250 240 10.2
150 162 7 12 162.2 156 7.1 240 260 10 18 260 250 10.2
150 162 7.5 12 162.2 156 7.6 250 270 10 18 270 260 10.2
150 165 10 16 165.6 157.6 10.2 260 275 10 18 275 270 10.2
150 166 10 16 166.6 157.6 10.2 260 280 10 18 280 270 10.2
152 160 5 7 160.6 155 5.3 270 290 10 18 290 280 10.2
155 167 7 12 167.2 161 7.1 280 300 10 18 300 290 10.2
155 169 7 12 169.2 161 7.1 295 315 10 18 315 305 10.2
155 170 10 16 170.6 162.6 10.2 300 320 10 18 320 310 10.2
155 175 10 18 175 165 10.2 330 354 8 15 354.6 339.4 8.3
160 168 5 7 168.6 163 5.3 360 380 10 18 380 370 10.2

66
WR A41

Wiper with a sharply-defined lip edge Installation


The wiper is built in to a semi-closed axial
Standard material groove. The recess on the atmospheric side
Elastomer NBR90 of the groove ensures good axial security
in the housing. The L, measurement, which
Area of application is dependent on the height of the wiper, is
Hydraulic and pneumatic systems, reciprocal selected as follows:
movements, medium dirt load
H (mm) ≤ 7 10 13
Function L, (mm) 1 1.5 2
The WR A41 is a single function wiper.
It is pressed against the descending piston rod Please also follow the general installation
wiping the dirt from the surface of the rod. instructions.
The seals, their associated elements and the
medium are protected from dirt. Pads on the Remarks
inner diameter support the correct functional fit In addition, we are able to supply other
and prevent additional pressure build-up in the dimensions required. For operational
back area which could press the wiper out of conditions outside the standard applications,
its housing. other elastomers, such as FKM for higher
temperatures, are available.
Media
Hydraulic oils acc. to DIN 51524/ 51525, The pads described in the function paragraph
lubricating oils, other mineral oil based fluids are not always taken into account outside the
and HFA, HFB, HFC highly non-flammable standard area in terms of tooling.
hydraulic fluids acc. to VDMA 24317

Operational application limits


Temperature (°C): -40 to +100
Running speed (m/s): up to 4

67
WR A41
Dimensions in mm Dimensions in mm
Ø dN ØDN L H ØD2 Ø dN ØDN L H ØD2
Sizes
metric

4 12 4 7 10 88 96 4 7 94
5 8 2.2 4 6.8 90 98 4 7 96
6 10 3 4 8.8 92 100 4 7 98
8 16 4 7 14 93 101 4 7 99
10 16 2.6 5 14 95 103 4 7 101
10 18 4 7 16 95 103 5.5 10 100
12 18 2.6 5 16 97 105 4 7 103
12 20 4 7 18 100 108 4 7 106
14 20 3.1 5 18 100 108 5.5 10 105
14 22 4 7 20 102 114 5.5 10 111
15 23 4 7 21 105 117 5.5 10 114
16 24 4 7 22 106 118 5.5 10 115
17 25 4 7 23 110 118 4 7 116
18 24 3.1 5 22 110 118 5.5 10 115
18 26 4 7 24 110 122 5.5 10 119
20 28 4 7 26 112 124 5.5 10 121
22 30 4 7 28 113 121 4 7 119
23 31 4 7 29 114 122 4 7 120
24 32 4 7 30 115 127 5.5 10 124
25 33 4 7 31 118 130 5.5 10 127
26 34 4 7 32 120 132 5.5 10 129
28 36 4 7 34 125 133 4 7 131
30 38 4 7 36 125 137 5.5 10 134
32 40 4 7 38 128 140 5.5 10 137
33 41 4 7 39 130 142 5.5 10 139
34 42 4 7 40 131 139 4 7 137
35 43 4 7 41 135 147 5.5 10 144
35 45 4 7 42.9 140 152 5.5 10 149
36 44 4 7 42 140 155 6.5 13 151
38 46 4 7 44 142 154 5.5 10 151
40 48 4 7 46 145 157 5.5 10 154
41 49 4 7 47 149 157 4 7 155
42 50 4 7 48 150 162 5.5 10 159
44 52 4 7 50 152 164 5.5 10 161
45 53 4 7 51 154 166 5.5 10 163
45 56 5 8 54.9 155 167 5.5 10 164
45 57 5.5 10 54 160 172 5.5 10 169
46 54 4 7 52 165 177 5.5 10 174
47 55 4 7 53 166 178 5.5 10 175
48 56 4 7 54 168 176 4 7 174
50 58 4 7 56 170 182 5.5 10 179
50 62 5.5 10 59 175 187 5.5 10 184
50 63 4 7 61 180 192 5.5 10 189
51 59 4 7 57 185 197 5.5 10 194
52 60 4 7 58 188 196 4 7 194
53 61 4 7 59 190 202 5.5 10 199
54 62 4 7 60 195 207 5.5 10 204
55 63 4 7 61 200 212 5.5 10 209
56 64 4 7 62 210 218 4 7 216
57 65 4 7 63 210 225 6.5 13 221
58 66 4 7 64 220 235 6.5 13 221
60 68 4 7 66 230 245 6.5 13 241
60 72 5.5 10 69 235 250 6.5 13 246
62 70 4 7 68 238 253 6.5 13 249
63 71 4 7 69 240 255 6.5 13 251
64 72 4 7 70 250 265 6.5 13 261
65 73 4 7 71 260 275 6.5 13 271
66 74 4 7 72 265 280 6.5 13 276
67 75 4 7 73 300 315 6.5 13 311
68 76 4 7 74 305 320 6.5 13 316
70 78 4 7 76 310 325 6.5 13 321
72 80 4 7 78 315 330 6.5 13 326
73 81 4 7 79 320 335 6.5 13 331
75 83 4 7 81 340 355 6.5 13 351
78 86 4 7 84 365 380 6.5 13 376
80 88 4 7 86 400 415 6.5 13 411
82 90 4 7 88 450 465 6.5 13 461
83 91 4 7 89 500 515 6.5 13 511
85 93 4 7 91
86 94 4 7 92

68
WR AD51

Double wiper with a sharply-defined lip edge Installation


and an additional sealing lip on the medium The wiper is built in to a semi-closed axial
side. groove. The recess on the atmospheric side
of the groove ensures good axial security in
Standard material the housing. Please also follow the general
Elastomer NBR90 installation instructions.

Area of application Remarks


Hydraulic and pneumatic systems, reciprocal In addition, we are able to supply other
movements, medium dirt load dimensions required. For operational
conditions outside the standard applications,
Function other elastomers, such as FKM for higher
The WR AD51 is a double function wiper. This temperatures, are available.
double function consists of wiping the dirt from
the surface of the descending piston rod on the
one hand and on the other, that the remaining
oil film is retained and returned to the system.
It is not necessary to drill a leakage hole if the
seals are placed according to the diagram.

Media
Hydraulic oils acc. to DIN 51524/ 51525,
lubricating oils, other mineral oil based fluids
and HFA, HFB, HFC highly non-flammable
hydraulic fluids acc. to VDMA 24317

Operational application limits


Temperature (°C): -40 to +100
Running speed (m/s): up to 1

69
WR AD51
Dimensions in mm Dimensions in mm
Ø dN ØDN L H ØD2 Ø dN ØDN L H ØD2
Sizes
metric

8 14 4 5 11.8 95 103 6 8 98.5


10 18 6 8 13.5 100 108 6 8 103.5
12 20 6 8 15.5 105 117 8.2 11 110
14 22 6 8 17.5 110 122 8.2 11 115
15 23 6 8 18.5 115 127 8.2 11 120
16 24 6 7 19.5 120 132 8.2 11 125
16 24 6 8 19.5 125 137 8.2 11 130
18 26 6 8 21.5 130 142 8.2 11 135
20 28 6 8 23.5 135 147 8.2 11 140
22 30 6 8 25.5 140 152 8.2 11 145
24 32 6 8 27.5 145 157 8.2 11 150
25 33 6 8 28.5 150 162 8.2 11 155
26 34 6 8 29.5 155 167 8.2 11 160
28 36 6 8 31.5 160 172 8.2 11 165
30 38 6 8 33.5 165 177 8.2 11 170
32 40 6 8 35.5 170 182 8.2 11 175
35 43 6 8 38.5 175 187 8.2 11 180
36 44 6 8 39.5 180 192 8.2 11 185
37 45 6 8 40.5 185 197 8.2 11 190
38 46 6 8 41.5 190 202 8.2 11 195
40 48 6 8 43.5 195 207 8.2 11 200
42 50 6 8 45.5 200 212 8.2 11 205
45 53 6 8 48.5 205 220 9.5 13 212
46 54 6 8 49.5 210 225 9.5 13 217
48 56 6 8 51.5 220 235 9.5 13 227
50 58 6 8 53.5 225 240 9.5 13 232
52 60 6 8 55.5 230 245 9.5 13 237
55 63 6 8 58.5 240 255 9.5 13 247
56 64 6 8 59.5 250 265 9.5 13 257
60 68 6 8 63.5 260 275 9.5 13 267
63 71 6 8 66.5 275 290 9.5 13 282
65 73 6 8 68.5 280 295 9.5 13 287
68 76 6 8 71.5 290 305 9.5 13 297
70 78 6 8 73.5 300 315 9.5 13 307
75 83 6 8 78.5 320 335 9.5 13 327
80 88 6 8 83.5 350 365 9.5 13 357
85 93 6 8 88.5 360 375 9.5 13 367
90 98 6 8 93.5 370 385 9.5 13 377

70
WR AD53

Double wiper with a sharply-defined lip edge Installation


and an additional sealing lip on the medium The wiper is built in to a semi-closed axial
side. groove. The recess on the atmospheric side
of the groove ensures good axial security in
Standard material the housing. Please also follow the general
Elastomer NBR90 installation instructions.

Area of application Remarks


Hydraulic and pneumatic systems, reciprocal In addition, we are able to supply other
movements, medium dirt load dimensions required. For operational
conditions outside the standard applications,
Function other elastomers, such as FKM for higher
The WR AD53 is a double function wiper. This temperatures, are available.
double function consists of wiping the dirt from
the surface of the descending piston rod on the
one hand and on the other, that the remaining
oil film is retained to be returned to the system
through a leakage drain with the next descent.

Media
Hydraulic oils acc. to DIN 51524/ 51525,
lubricating oils, other mineral oil based fluids
and HFA, HFB, HFC highly non-flammable
hydraulic fluids acc. to VDMA 24317

Operational application limits


Temperature (°C): -40 to + 100
Running speed (m/s): up to 1

71
WR AD53
Dimensions in mm Dimensions in mm
Ø dN ØDN h H ØD1 ØD2 L Ø dN ØDN h H ØD1 ØD2 L
Sizes
metric

12 18 3.5 4.8 18.6 15 3.8 63 71 5 7 71.6 66 5.3


12 20 5 7 20.6 15 5.3 65 73 5 7 73.6 68 5.3
16 22 3.5 4.8 22.6 19 3.8 65 75 5 7 75.6 68 5.3
18 24 3.5 4.8 24.6 21 3.8 66 74 5 7 74.6 69 5.3
20 28 5 7 28.6 23 5.3 70 78 5 7 78.6 73 5.3
22 30 5 7 30.6 25 5.3 70 80 5 7 80.6 73 5.3
25 33 5 7 33.6 28 5.3 75 87 7 12 87.2 81 7.1
28 36 5 7 36.6 31 5.3 76.5 88.5 7 12 88.7 82.5 7.1
30 38 5 7 38.6 33 5.3 78 92 7 12 92.2 85 7.1
32 40 5 7 40.6 35 5.3 80 92 7 12 92.2 86 7.1
35 43 5 7 43.6 38 5.3 85 97 7 12 97.2 91 7.1
36 44 5 7 44.6 39 5.3 90 100 6 8 100.6
92.8 6.2
40 48 5 7 48.6 43 5.3 90 102 7 12 102.2
96 7.1
42 50 5 7 50.6 45 5.3 95 107 7 12 107.2 101 7.1
45 53 5 7 53.6 48 5.3 115 127 7 12 127.2 121 7.1
45 55 5 7 55.6 48 5.3 125 140 7.5 9.5 140.2 110 7.6
50 58 5 7 58.6 53 5.3 135 147 7 12 147.2 141 7.1
50 60 5 7 60.6 53 5.3 155 167 7 12 167.2 161 7.1
55 63 5 7 63.6 58 5.3 160 172 7 12 172.2 166 7.1
55 65 5 7 65.6 58 5.3 185 197 7 12 197.2 191 7.1
56 64 5 7 64.6 59 5.3 215 227 7 12 227.2 221 7.1
60 68 5 7 68.6 63 5.3 240 255 7 12 255.2 247 7.1
60 70 5 7 70.6 63 5.3 280 305 15.7 22.5 305 292.6 15.8

72
WR AM43

Elastomer wiper with a sharply-defined lip Installation


edge and metal housing. The two parts are The wiper is easily built in to split housing,
vulcanized into a single unit. provided the lead-in chamfer Ll is in
accordance with the table below:
Standard material
Elastomer NBR90, H (mm) L1 (mm)
Steel acc. to DIN 1624 ≤ 4.5 0.6
5 0.6
Area of application
6 0.8
Hydraulic and pneumatic systems, reciprocal
7 0.8
movements, medium dirt load
8 1

Function 9 1

The WR AM43 is a single function wiper. It is 10 1.4

pressed against the descending piston rod 12 1.8


wiping the dirt from the surface of the rod. 14 2
The seals, their associated elements and the 16 2.4
hydraulic medium are protected from dirt.
The metal angle ring with its additional press Please also follow the general installation
fit on the outer circumference, ensures the instructions.
functionally correct fit of the wiper in the
housing. Remarks
In addition, we are able to supply other
Media dimensions required. For operational
Hydraulic oils acc. to DIN 51524/ 51525, conditions outside the standard applications,
lubricating oils, other mineral oil based fluids other elastomers, such as FKM for higher
and HFA, HFB, HFC highly non-flammable temperatures, are available.
hydraulic fluids acc. to VDMA 24317

Operational application limits


Temperature (°C): -40 to +100
Running speed (m/ s): up to 1

73
WR AM43
Dimensions in mm Dimensions in mm
Ø dN ØDN h=L H Ø dN ØDN h=L H
Sizes
metric

6 13 3 4.5 28 38 5 8
6 14 5 8 28 38 7 10
8 14 3.5 5 28 40 7 10
8 15 3 4.5 29.5 40 7 10
8 16 5 8 30 40 5 7
8 18 6 9 30 40 5 8
8 22 3 4.5 30 40 7 10
10 16 3 4.5 30 42 5 8
10 16 5 7 30 42 7 10
10 18 5 8 30 45 5 8
10 20 5 7 30 45 7 10
10 20 5 8 32 40 4 7
12 18 3 4 32 40 7 10
12 20 4 6 32 42 5 7
12 22 5 8 32 42 7 10
12 22 7 10 32 45 4 8
12 25 5 8 32 45 5 8
14 20 3 4.5 32 45 7 10
14 20 4 5 32 50 7 10
14 22 3 4 33 43 5 8
14 24 7 10 33 43 7 10
14 25 5 8 35 45 5 7
15 25 5 8 35 45 7 10
15 25 7 10 35 47 7 10
16 22 3 4 35 48 5 8
16 22 3.5 5 35 48 6.5 12
16 22 4 6 35 50 9 12
16 22 5 8 35 52 7 10
16 24 3 4.5 36 45 7 10
16 26 5 8 36 46 5 7
16 26 7 10 36 46 7 10
17 22 5 8 38 48 7 10
18 26 3 4 38.1 47.62 7 10
18 26 5 7 39.5 50 7 10
18 28 5 6 40 50 3.5 5
18 28 7 10 40 50 5 8
18 28 7 12 40 50 7 10
18 35 5 8 40 52 5 8
19 27 6.4 9.5 40 52 7 10
20 26 4 7 40 55 9 12
20 26 5 8 40 62 7 10
20 27 7 10 42 52 7 10
20 28 3.5 5 44 55 5 8
20 28 5 8 45 55 5 7
20 30 4 6 45 55 7 10
20 30 5 8 45 60 7 10
20 30 7 10 47 57 7 10
20 35 7 10 48 60 7 10
22 28 5 8 50 56 4 6
22 30 5 8 50 56 5 7
22 32 4 6 50 56 5 8
22 32 5 8 50 60 5 7
22 32 7 10 50 60 7 10
22 35 5 8 50 65 5 8
22 35 7 10 50 65 7 10
22 38 5 8 52 62 7 10
24 32 5 7 55 63 7 10
24 35 7 10 55 65 5 7
24 37 7 10 55 65 7 10
25 35 3 4 55 80 5 8
25 35 5 8 56 65 7 10
25 35 7 8.8 56 66 5 8
25 35 7 10 56 66 7 10
25.4 34 5 8 60 68 5 8
26 34 5 8 60 70 5 7
26 35 7 10 60 70 7 10
28 34 5 7 60 74 5 8

74
WR AM43
Dimensions in mm Dimensions in mm
Ø dN ØDN h=L H Ø dN ØDN h=L H
Sizes
metric

60 75 7 10 120 135 6 10
60 80 7 10 123 147 9 12
61 72 7 10 125 140 7 10
63 72 7 10 125 140 9 12
63 73 6 9 130 140 7 10
63 73 7 10 130 145 9 12
63 75 7 10 135 145 7 10
63 83 5 8 135 150 9 12
65 75 5 7 140 150 7 10
65 75 7 10 140 155 9 12
70 80 5 7 145 160 9 12
70 80 7 10 145 165 10 14
70 90 7 10 150 165 9 12
72 82 7 10 150 166 8 12
73 89 7 10 160 175 9 12
74 85 7 10 160 176 8 12
75 85 7 10 165 180 9 12
75 87 5 7 165 180 12 16
75 87 7 10 170 185 10 14
78 88 7 10 175 190 9 12
80 90 7 10 180 195 10 14
80 100 12 15 185 200 10 14
82 92 7 10 185 201 8 12
82.55 92 7 10 190 210 10 14
84 94 5 8 190 220 9 12
85 95 7 10 200 215 9 12
90 100 5 7 200 220 10 14
90 100 7 10 200 220 12 16
94 115 7 10 210 230 10 14
95 105 7 10 212 227 7.5 11.5
95 106 7 10 220 240 12 16
100 110 5 8 230 246.5 8 12
100 110 7 10 240 260 12 16
100 115 8 10 250 270 12 16
100 115 9 12 270 295 12 16
105 115 7 10 275 300 12 16
108 120 7 10 280 300 12 16
110 120 7 10 320 340 12 16
110 125 9 12 360 380 12 16
115 125 7 10 400 420 12 16
120 130 7 10

75
WR AM45

Elastomer wiper with a sharply-defined lip Installation


edge and metal housing. The two parts are The wiper is easily built in to split housing,
vulcanized into a single unit. provided the lead-in chamfer Ll is in
accordance with the table below:
Standard material
Elastomer NBR90, Steel acc. to DIN 1624 H (mm) L1 (mm)
≤ 4.5 0.6
Area of application
5 0.6
Hydraulic and pneumatic systems,
6 0.8
reciprocal movements,
7 0.8
medium dirt load
10 1.4

Function 12 1.8

The WR AM45 is a single function wiper. It is 14 2

pressed against the descending piston rod 16 2.4


wiping the dirt from the surface of the rod.
The seals, their associated elements and the Please also follow the general installation
hydraulic medium are protected from dirt. instructions.
The elastomer-coated metal ring with its
additional press fit on the outer circumference, Remarks
ensures the functionally correct fit of the wiper In addition, we are able to supply other
in the housing. dimensions required. For operational
conditions outside the standard applications,
Media other elastomers, such as FKM for higher
Hydraulic oils acc. to DIN 51524/ 51525, temperatures, and metals are available.
lubricating oils, other mineral oil based fluids
and HFA, HFB, HFC highly non-flammable
hydraulic fluids acc. to VDMA 24317

Operational application limits


Temperature (°C): -40 to +100
Running speed (m/s): up to 1

76
WR AM45
Dimensions in mm Dimensions in mm
Ø dN ØDN h H L Ø dN ØDN h H L
Sizes
metric

6 13 3 4.5 3.5 40 50 5 8 5.5


8 14 3.5 5 4 40 50 7 10 7.5
10 16 3.5 5 4 42 52 5 7 5.5
10 20 5 7 5.5 42 52 7 10 7.5
12 18 3.5 5 4 44 55 7 10 7.5
12 20 4 6 4.5 45 55 5 7 5.5
12 22 5 8 5.5 45 55 7 10 7.5
12.7 18 3 4.5 3.5 45 60 7 10 7.5
14 20 3.5 5 4 48 60 7 10 7.5
14 22 3 4 3.5 50 60 5 7 5.5
15 21 3.5 5 4 50 60 5 8 5.5
15 25 5 7 5.5 50 60 7 10 7.5
16 22 3 4 3.5 50 65 7 10 7.5
16 22 3.5 5 4 52 62 7 10 7.5
16 22 4 6 4.5 55 63 7 10 7.5
16 24 3.5 5 4 55 65 5 7 5.5
16 26 5 8 5.5 55 65 7 10 7.5
17 22 5 7 5.5 56 66 5 7 5.5
18 28 5 7 5.5 60 70 5 7 5.5
18 28 7 10 7.5 60 70 7 10 7.5
19 26 5 8 5.5 63 73 5 7 5.5
20 28 3.5 5 4 63 75 7 10 7.5
20 28 7 10 7.5 65 75 5 7 5.5
20 30 4 6 4.5 65 75 7 10 7.5
20 30 5 7 5.5 70 80 5 7 5.5
20 30 7 10 7.5 70 80 7 10 7.5
22 28 5 7 5.5 75 83 7 10 7.5
22 32 5 7 5.5 75 85 7 10 7.5
22 32 7 10 7.5 80 88 7 10 7.5
24 35 5 8 5.5 80 90 7 10 7.5
25 32 5 7 5.5 85 95 7 10 7.5
25 33 4 7 4.5 90 100 5 7 5.5
25 35 5 7 5.5 90 100 7 10 7.5
25 35 7 10 7.5 95 105 7 10 7.5
25.4 34 5 8 5.5 100 110 7 10 7.5
26 35 7 10 7.5 105 115 7 10 7.5
28 38 5 7 5.5 110 120 7 10 7.5
28 40 7 10 7.5 110 125 7 10 7.5
30 40 5 7 5.5 115 125 7 10 7.5
30 40 7 10 7.5 120 130 7 10 7.5
32 42 5 7 5.5 125 140 9 12 9.5
32 42 7 10 7.5 130 145 9 12 9.5
32 45 4 6 4.5 140 155 9 12 9.5
32 45 7 10 7.5 150 165 9 12 9.5
35 45 5 7 5.5 160 175 9 12 9.5
35 45 7 10 7.5 170 185 10 14 10.5
36 45 7 10 7.5 180 195 10 14 10.5
36 46 5 7 5.5 200 220 12 16 12.5
38 48 7 10 7.5 220 240 12 16 12.5

77
WR A42

Wiper with a less than Installation


45° sharply-defined lip edge The wiper is built in to a semi-closed axial
groove. The recess on the atmospheric side of
Standard material the groove ensures good axial security in the
Polyurethane TPU92 housing. The radius R, which is dependent on
the height of the wiper, is selected as follows:
Area of application
Hydraulic and pneumatic systems, H (mm ) ≤12 16 18
reciprocal movements, R (mm) 1 1.5 3
medium to heavy dirt load
Please also follow the general installation
Function instructions.
The WR A42 is a single function wiper.
It is pressed against the descending piston Remarks
rod wiping the dirt from the surface of the In addition, we are able to supply other
rod. The seals, their associated elements and dimensions required. For operational conditions
the medium are protected from dirt. The high outside the standard applications, other
wear-resistance of the polyurethane provides polyurethane materials are available.
this wiper with a particularly long service life.
Pads on the inner diameter support the correct The pads described in the function paragraph
functional fit and prevent additional pressure are not always taken into account outside the
build-up in the back area which could press the standard area in terms of tooling.
wiper out of its housing.

Media
Hydraulic oils acc. to DIN 51524/ 51525,
lubricating oils, other mineral oil based fluids
and HFA, HFB, HFC highly non-flammable
hydraulic fluids acc. to VDMA 24317

Operational application limits


Temperature (°C): -40 to + 100
Running speed (m/s): up to 2

78
WR A42
Dimensions in mm Dimensions in mm
Ø dN ØDN h H ØD1 ØD2 L Ø dN ØDN h H ØD1 ØD2 L
Sizes
metric

4 12 2.7 4 12 9 3 78 92 7 12 92.2 85 7.1


5 12 2.5 4 12 9 2.8 80 88 5 7 88.6 83 5.3
6 12 2.7 4 12 9 3 80 92 7 12 92.2 86 7.2
8 14 3.5 4.5 14.6 11 3.8 85 93 5 7 93.6 88 5.3
9 13 2.2 3.5 13 12 2.5 85 97 7 12 97.2 91 7.2
10 16 3.5 5 16.6 13 3.8 90 102 5.8 8 102.2 94 6
12 18 3.5 5 18.6 15 3.8 90 102 7 12 102.2 96 7.2
14 20 3.5 5 20.6 17 3.8 91 97 5 7 97.6 94 5.3
15 21 3.5 5 21.6 18 3.8 92 103 5.2 7 103.6 97 5.5
16 22 2.8 4 22.6 19 3 93 101 4.7 7 101 96 5
16 22 3.5 5 22.6 19 3.8 95 107 7 12 107.2 101 7.1
16 24 5 7 24.6 19 5.3 97 105 4.7 7 105 100 5
18 24 3.5 5 24.6 21 3.8 99 109 5.2 7 109.6 105.5 5.5
18 26 5 7 26.6 21 5.3 100 112 5.8 8 112.2 104
20 26 3.1 4.5 26 23 3.4 100 112 7 12 112.2 106 7.2
20 28 4.8 7 28.3 23.8 5 105 113 5 7 113.6 108 5.3
20 28 5 7 28.6 23 5.3 105 117 7 12 117.2 111 7.2
22 30 5 7 30.6 25 5.3 107 113 5 7 113.6 110 5.3
24 32 5 7 32.6 27 5.3 110 122 7 12 122.2 116 7.2
25 33 4.8 7 33.3 29.2 5 112 124 7 12 124.2 118 7.1
25 33 5 7 33.6 28 5.3 115 127 7 12 127.2 121 7.2
28 36 5 7 36.6 31 5.3 118 126 4.7 7 126 121 5
30 38 5 7 38.6 33 5.3 119 134 9.3 12.3 134.5 124.7 9.5
30 40 2.8 4 40 34.5 3 120 130 5.2 7 130.6 126.5 5.5
30 45 5 7 45.3 35.5 5.3 120 132 7 12 132.2 126 7.2
32 40 3.5 5 40 35 3.8 125 133 5 7 133.6 128 5.3
32 40 5 7 40.6 35 5.3 125 137 7 12 137.2 131 7.1
32 42 4 6 42 35 4.2 125 140 10 16 140 132.6 10.2
35 40 3.5 5 40 38 3.8 128 140 7 12 140.2 134 7.1
35 43 5 7 43.6 38 5.3 130 142 7 12 142.2 136 7.1
35 45 3.8 6 45 39 4 135 147 7 12 147.2 141 7.1
36 44 5 7 44.6 39 5.3 140 148 5.8 7 148.6 143 6
38 46 5 7 46.6 41 5.3 140 152 7 12 152.2 146 7.1
38 48 4.5 7 48.6 41 4.8 140 152 8.7 15 152 147 9
40 48 4 7 48 43 4.2 140 155 8.7 15 155 147.5 9
40 48 5 7 48.6 43 5.3 140 155 10 16 155 147.6 10.2
42 50 5 7 50.6 45 5.3 141 151 5.2 7 151.6 147.5 5.5
45 53 5 7 53.6 48 5.3 143 151 5.2 7 151 146 5.5
45 55 5 7 55.6 48 5.3 145 153 5 7 153.6 148 5.3
45 60 4 6 60 53 4.2 145 157 7 12 157.2 151 7.1
46 54 5 7 54.6 49 5.3 145 160 9 16 160.7 152.2 9.2
48 56 5 7 56.6 51 5.3 150 162 7 12 162.2 156 7.1
50 58 4 6 58.6 53 4.3 150 165 7.2 12 165 156 7.5
50 58 5 7 58.6 53 5.3 150 165 10 16 165 157.6 10.2
50 60 5 7 60.6 53 5.3 155 170 10 16 170 162.6 10.2
50 65 4 6 65.6 53 4.2 160 172 7 12 172.2 166 7.1
53 61 5 7 61.6 56 5.3 160 175 8.7 15 175 167 9
55 63 5 7 63.6 58 5.3 160 175 10 16 175 167.6 10.2
55 65 5 7 65.6 58 5.3 162 172 5.2 7 172.6 168 5.5
56 64 5 7 64.6 59 5.3 170 178 5 7 178.6 173 5.3
56 66 5 7 66.6 59 5.3 170 182 7 12 182.2 176 7.2
60 68 5 7 68.6 63 5.3 170 182 10 16 182 177.6 10.2
60 70 5 7 70.6 63 5.3 170 185 10 16 185.2 178 10.1
60 70 5.2 7 70.6 66.5 5.5 171 186 10 16 187 178.2 10.2
61 67 5 7 67.6 64 5.3 180 195 10 16 195.2 188 10.1
63 71 5 7 71.6 66 5.3 180 200 7 12 200.2 188 7.1
63 73 5 7 73.6 66 5.3 180 200 10 18 200 190 10.2
65 73 5 7 73.6 68 5.3 183 193 5.2 7 193.6 189 5.5
65 75 5 7 75.6 68 5.3 190 205 10 18 205.2 198 10.1
65 76 5.8 7 76.6 71.5 6 190 210 10 18 210 200 10.2
65 77 7 12 77.2 71 7.2 200 215 9.3 16 216 207.2 9.5
67 76 5.2 7 76.6 71 5.5 200 215 10 16 215.2 208 10.1
70 78 5 7 78.6 73 5.3 200 220 10 18 220 210 10.2
70 80 5 7 80.6 73 5.3 205 213 5 7 213.6 208 5.3
70 80 7 10 80.5 72.6 7.2 210 225 10 16 225.2 218 10.1
70 82 7 12 82.6 76 7.1 220 235 10 16 235 227.6 10.2
73 81 5 7 81.6 76 5.3 220 240 10 16 240 227.6 10.2
73 83 7 12 83.6 76 7.1 230 245 10 16 245.2 238 10.1
75 83 5 7 83.6 78 5.3 240 255 10 16 255.2 248 10.1
75 87 7 12 87.2 81 7.2 250 265 10 16 265.2 258 10.2
76 82 5 7 82.6 81 5.3 257 267 5.2 7 267.6 264 5.5
78 86 5 7 86.6 81 5.3 280 300 10 18 300 290 10.2
78 88 5.2 7 88.6 84.5 5.5 300 320 10 18 320 310 10.2

79
WR A47

Wiper with a sharply-defined lip edge Installation


The wiper is built in to a semi-closed axial
Standard material groove. The recess on the atmospheric side
Polyurethane TPU92 of the groove ensures good axial security
in the housing. The Ll measurement, which
Area of application is dependent on the height of the wiper, is
Hydraulic and pneumatic systems, selected as follows:
reciprocal movements,
medium to heavy dirt load H (mm ) ≤ 7 10
R (mm) 1 1.5
Function
The WR A47 is a single function wiper. Please also follow the general installation
It is pressed against the descending piston rod instructions on page 13 of this catalogue.
wiping the dirt from the surface of the rod.
The seals, their associated elements and the Remarks
medium are protected from dirt. The high wear- In addition, we are able to supply other
resistance of the polyurethane provides this dimensions required. For operational conditions
wiper with a particularly long service life. outside the standard applications, other
polyurethane materials are available.
Media
Hydraulic oils ace. to DIN 51524/ 51525,
lubricating oils, other mineral oil based fluids
and HFA, HFB, HFC highly non-flammable
hydraulic fluids ace. to VDMA 24317

Operational application limits


Temperature (°C): -40 to + 100
Running speed (m/s): up to 2

80
WR A47
Dimensions in mm Dimensions in mm
Ø dN ØDN L h H ØD2 Ø dN ØDN L h H ØD2
Sizes
metric

10 16 4 3.8 7 14 70 78 4 3.8 7 76
10 18 4 3.8 7 16 75 83 4 3.8 7 81
12 20 4 3.8 7 18 78 86 4 3.8 7 84
14 22 4 3.8 7 20 80 88 4 3.8 7 86
16 24 4 3.8 7 22 85 93 4 3.8 7 91
18 26 4 3.8 7 24 90 98 4 3.8 7 96
20 28 4 3.8 7 26 95 103 4 3.8 7 101
22 30 4 3.8 7 28 100 108 4 3.8 7 106
25 33 4 3.8 7 31 105 117 5.5 5 10 114
26 34 4 3.8 7 32 110 122 5.5 5 10 119
28 36 4 3.8 7 34 115 127 5.5 5 10 124
30 38 4 3.8 7 36 120 132 5.5 5 10 129
32 40 4 3.8 7 38 125 137 5.5 5 10 134
34 42 4 3.8 7 40 130 142 5.5 5 10 139
35 43 4 3.8 7 41 135 147 5.5 5 10 144
36 44 4 3.8 7 42 140 152 5.5 5 10 149
38 46 4 3.8 7 44 145 157 5.5 5 10 154
40 48 4 3.8 7 46 150 162 5.5 5 10 159
42 50 4 3.8 7 48 160 172 5.5 5 10 169
45 53 4 3.8 7 51 170 182 5.5 5 10 179
50 58 4 3.8 7 56 180 192 5.5 5 10 189
50 62 5.5 5 10 60 190 202 5.5 5 10 199
55 63 4 3.8 7 61 200 212 5.5 5 10 209
56 64 4 3.8 7 62 220 235 5.5 5 10 232
60 68 4 3.8 7 66 230 245 5.5 5 10 242
62 70 4 3.8 7 68 240 255 5.5 5 10 252
63 71 4 3.8 7 69 260 275 5.5 5 10 272
65 73 4 3.8 7 71 275 290 5.5 5 10 287

81
WR AD48

Double wiper with a sharply-defined lip edge Installation


and an additional sealing lip The wiper is built in to a semi-closed axial
groove. The recess on the atmospheric side
Standard material of the groove ensures good axial security in
Polyurethane TPU92 the housing. Please also follow the general
installation instructions.
Area of application
Hydraulic and pneumatic systems, Remarks
reciprocal movements, In addition, we are able to supply other
medium to heavy dirt load dimensions required.
For operational conditions outside the standard
Function applications, other polyurethane materials are
The WR AD48 is a double function wiper. This available.
double function consists of wiping the dirt from
the surface of the descending piston rod on the
one hand and on the other, that the remaining
oil film is retained and returned to the system
through a leakage drain. The high wear-
resistance of the polyurethane provides this
wiper with a particularly long service life.

Media
Hydraulic oils acc. to DIN 51524/51525,
lubricating oils, other mineral oil based fluids
and HFA, HFB, HFC highly non-flammable
hydraulic fluids acc. to VDMA 24317

Operational application limits


Temperature (°C): -40 to + 100
Running speed (m/s): up to 1

82
WR AD48
Dimensions in mm Dimensions in mm
Ø dN ØDN h H ØD1 ØD2 L Ø dN ØDN h H ØD1 ØD2 L
Sizes
metric

10 16 3.6 4.8 16.6 13 3.8 56 66 5.3 6.8 66 59 6


12 18 3.6 4.8 18.6 15 3.8 60 68 5 6.8 68.6 63 5.3
14 20 3.6 4.8 20.6 17 3.8 60 70 5 6.8 70.6 63 5.3
16 22 3.6 4.8 22.6 19 3.8 63 71 5 6.8 71.6 66 5.3
18 24 3.6 4.8 24.6 21 3.8 63 73 5 6.8 73.6 66 5.3
20 26 3.6 4.8 26 22.5 4 65 73 5 6.8 73.6 68 5.3
20 28 5 6.8 28.6 23 5.3 65 75 5 6.8 75.6 68 5.3
22 28 3.6 4.8 28.6 25 3.8 70 78 5 6.8 78.6 73 5.3
22 30 5 6.8 30.6 25 5.3 70 80 5 6.8 80.6 73 5.3
24 32 5 6.8 32.6 27 5.3 75 83 5 6.8 83.6 78 5.3
25 31 3.6 4.8 31.6 28 3.8 75 85 5 6.8 85.6 78 5.3
25 33 5 6.8 33.6 28 5.3 75 87 7 9 87.2 81 7.1
28 36 4.5 5.8 36 31 5 80 88 5 6.8 88.6 83 5.3
28 36 5 6.8 36.6 31 5.3 80 90 5.3 6.8 90 83 6
30 38 4.5 5.8 38 33 5 80 90 7 12 90.4 83 7.2
30 38 5 6.8 38.6 33 5.3 80 92 7 9 92.2 86 7.1
32 40 4.5 5.8 40 35 5 85 97 7 10 97.2 91 7.1
32 40 5 6.8 40.6 35 5.3 90 100 5.3 6.8 100 93 6
35 43 5 6.8 43.6 38 5.3 90 102 7 9 102.2
96 7.1
36 44 4.5 5.8 44 39 5 95 107 7 9 107.2 101 7.1
36 44 5 6.8 44.6 39 5.3 100 112 7 9 112.2 106 7.1
37 45 4.5 5.8 45 40 5 110 122 7 10 122.2 116 7.1
40 48 4.5 5.8 48 43 5 110 125 7.5 9.5 125 114 8.5
40 48 5 6.8 48.6 43 5.3 114 129 7 9 129.2 120 7.1
45 53 4.5 5.8 53 48 5 115 127 7 9 127.2 121 7.1
45 53 5 6.8 53.6 48 5.3 125 140 7.5 9.5 141 128.6 7.7
45 55 5 6.8 55.6 48 5.3 135 147 7 9 147.2 141 7.1
46 54 4.5 5.8 54 49 5 135 150 7 12 150.6 141.5 7.2
50 58 4.5 5.8 58 53 5 140 155 7.5 9.5 155 144 8.5
50 58 5 6.8 58.6 53 5.3 155 167 7 9.5 167.2 161 7.1
50 60 5 6.8 60.6 53 5.3 160 172 7 9.5 172.2 166 7.1
55 63 5 6.8 63.6 58 5.3 185 197 7 9.5 197.2 191 7.1
55 65 5 6.8 65.5 58 5.3 215 227 7 9.5 227.2 211 7.1
56 64 5 6.8 64.6 59 5.3 240 255 7 9.5 255.2 246 7.1

83
WR AM44

Elastomer wiper with a Installation


sharply-defined lip edge and metal The wiper is easily built in to split housing,
housing. These two parts are combined in a provided the lead-in chamfer L1 is in
manufacturing process to form a single unit. accordance with the table below:

Standard material H (mm) L1 (mm)


Polyurethane TPU92, ≤ 4.5 0.6
Steel acc. to DIN 1624
5 0.6
6 0.8
Area of application
8 1
Hydraulic and pneumatic systems,
10 1.4
reciprocal movements,
heavy dirt load 11 1.8
12 1.8

Function 14 2
The WR AM44 is a single function wiper. It is 16 2.4
pressed against the descending piston rod
wiping the dirt from the surface of the rod. Please also follow the general installation
The seals, their associated elements and instructions.
the hydraulic medium are protected from
dirt. The metal angle ring with its additional Remarks
press fit on the outer circumference, ensures In addition, we are able to supply other
the functionally correct fit of the wiper in dimensions required. For operational conditions
the housing. The high wear-resistance of outside the standard applications, other
the polyurethane provides this wiper with a polyurethane materials and metals are
particularly long service life. available.

Media
Hydraulic oils acc. to DIN 51524/ 51525,
lubricating oils, other mineral oil based fluids
and HFA, HFB, HFC highly non-flammable
hydraulic fluids acc. to VDMA 24317

Operational application limits


Temperature (°C): -40 to +100
Running speed (m/s): up to 2

84
WR AM44
Dimensions in mm Dimensions in mm
Ø dN ØDN h=L H Ø dN ØDN h=L H
Sizes
metric

8 14 3.5 5 36 50 7 10
8 18 5 7 38 48 7 10
9 19 5 7 38 50 7 10
10 16 3.5 5 40 50 5 8
10 18 5 8 40 50 7 10
10 20 5 8 40 52 7 10
12 18 3.5 5 40 60 7 10
12 18 4 6 42 52 5 8
12 20 4 6 42 52 7 10
12 22 5 8 45 55 5 8
14 20 3.5 5 45 55 7 10
14 24 5 7 45 57 7 10
14 25 3.5 5 45 60 7 10
15 21 3.5 5 47 59 7 10
15 25 5 8 48 60 7 10
16 22 3 4 48 62 7 10
16 22 3.5 5 50 56 5 8
16 22 4 6 50 60 5 8
16 26 5 8 50 60 7 10
17 24 3.5 5 50 62 5 8
18 28 5 7 50 62 7 10
18 28 5 8 52 62 7 10
18 28 7 10 53 67 8 11
18 30 6 9 55 63 7 10
19 26 5 8 55 65 5 8
19 27 4 5.2 55 65 7 10
19 27 6.4 9.5 55 69 8 11
20 26 5 8 56 66 5 8
20 28 3 4.5 56 66 7 10
20 28 3.5 5 56 70 8 11
20 30 4 6 60 70 5 8
20 30 5 8 60 70 7 10
20 30 7 10 60 74 5 8
20 32 6 9 60 74 8 11
22 28 5 8 60 80 7 10
22 32 5 8 63 73 5 8
22 32 7 10 63 73 7 10
24 35 5 8 63 75 7 10
25 32 5 8 63 77 8 11
25 35 5 8 64 78 8 11
25 35 7 10 65 75 5 8
25 37 6 9 65 75 7 10
26 34 5 8 65 79 8 11
27 39 6 9 67 81 8 11
28 38 5 8 70 80 5 8
28 38 7 10 70 80 7 10
28 40 6 9 70 84 8 11
28 40 7 10 71 85 8 11
30 40 5 8 75 83 7 10
30 40 7 10 75 85 7 10
30 42 6 9 75 89 8 11
30 45 5 8 77 87 7 10
32 42 5 8 80 88 7 10
32 42 7 10 80 90 7 10
32 44 7 10 80 94 8 11
32 45 4 6 82 92 7 10
32 45 7 10 85 95 7 10
33 43 7 10 85 99 8 11
35 45 7 10 90 100 7 10
35 47 7 10 90 104 8 11
36 45 5 8 90 110 10 14
36 45 7 10 92 106 8 11
36 46 5 7 95 105 7 10
36 46 7 10 95 109 8 11

85
WR AM44
Dimensions in mm Dimensions in mm
Ø dN ØDN h=L H Ø dN ØDN h=L H
Sizes
metric

100 110 7 10 160 175 9 12


100 114 8 11 160 180 10 14
100 115 8 11 165 185 10 14
105 115 7 10 170 190 10 14
105 121 9 12 175 195 10 14
106 122 9 12 180 195 10 14
110 120 7 10 180 205 12 17
110 126 9 12 190 215 12 17
112 128 9 12 200 220 12 16
115 125 7 10 200 225 12 17
118 134 9 12 210 235 12 17
120 130 7 10 212 237 12 17
120 136 9 12 220 245 12 17
125 140 9 12 224 249 12 17
125 141 9 12 225 250 12 17
130 145 9 12 230 255 12 16
130 146 9 12 236 261 12 17
132 148 9 12 240 265 12 17
135 150 9 12 250 275 12 17
135 155 10 14 265 290 12 17
140 155 9 12 270 295 12 16
140 160 10 16 280 300 12 16
145 165 10 14 280 310 16 20
150 165 9 12 300 330 10 16
150 170 10 14

86
WR AM54

Elastomer wiper with a Operational application limits


sharply-defined lip edge and metal Temperature (°C): -40 to +100
housing. These two parts are combined in a Running speed (m/s): up to 1
manufacturing process to form a single unit.
Installation
Standard material The wiper is easily built in to split housing with
Polyurethane TPU92, an lead-in chamfer of less than 30°. Please also
Steel acc. to DIN 1624 follow the general installation instructions.

Area of application Remarks


Hydraulic and pneumatic systems, In addition, we are able to supply other
reciprocal movements, dimensions required. For operational conditions
slow swivelling movements, outside the standard applications, other
medium to heavy dirt load polyurethane materials and metals are
available.
Function
The WR AM54 is a single function wiper. It is
pressed against the descending piston rod
wiping the dirt from the surface of the rod.
The seals, their associated elements and
the hydraulic medium are protected from
dirt. The metal angle ring with its additional
press fit on the outer circumference, ensures
the functionally correct fit of the wiper in
the housing. The high wear-resistance of
the polyurethane provides this wiper with a
particularly long service life.

Media
Hydraulic oils acc. to DIN 51524/ 51525,
lubricating oils, other mineral oil based fluids
and HFA, HFB, HFC highly non-flammable
hydraulic fluids acc. to VDMA 24317

87
WR AM54
Dimensions in mm Dimensions in mm
Ø dN ØDN H=L Ø dN ØDN H=L
Sizes
metric

15 21 5 80 90 7
16 23 5 80 94 8
20 28 5 80 95 5
25 32 7 80 95 7.5
25 38 7.5 80 95 8
30 40 4 80 100 10
30 43 7.5 85 99 8
35 45 4 85 100 4
35 50 7.5 85 100 10
36 46 7 85 105 10
36 48 6 90 100 7
38 50 7.5 90 104 8
40 50 4 90 105 6
40 50 4.2 90 105 8
40 52 6 90 106 8
40 52 7 90 110 8
42 52 7 90 110 10
45 55 3.2 95 109 8
45 55 4 95 110 8
45 55 5 95 115 10
45 57 7 100 114 8
45 60 7.5 100 115 4
50 60 4 100 115 6.5
50 60 5 100 115 7.5
50 60 7 100 115 9
50 62 7 100 116 8
50 63 4 100 120 8
50 65 7.5 100 120 10
55 65 3.2 105 120 7.5
55 68 4 110 125 8
55 69 8 110 125 9
55 70 7.5 110 126 8
56 70 7.5 110 126 9
60 70 5 110 130 9
60 74 8 110 130 10
60 75 4 115 130 8
60 75 5 120 135 8
60 75 7.5 120 136 9
60 75 8 120 140 8
63 73 7 120 140 10
63 78 7.5 120 150 12
65 75 7 125 140 9
65 79 8 130 145 7.5
65 80 5 130 146 9
65 80 7.5 130 150 7.5
70 80 5 130 150 8
70 80 7 130 154 8
70 84 4 140 160 10
70 84 7.5 140 162 7.5
70 84 8 150 175 9
70 85 7.5 160 175 10
70 85 8 160 180 10
71 86 5 160 190 9
75 89 8 170 190 9
75 90 7.5 170 200 10
75 95 10 190 210 10
76.5 96.5 10

88
WR ADM55

Double wiper with a less than Operational application limits


4SO sharply-defined lip edge with an additional Temperature (°C): -40 to +100
sealing lip in a metal housing. These two parts Running speed (m/s): up to 1
are combined in a manufacturing process to
form a single unit. Installation
The wiper is easily built in to split housing,
Standard material provided the lead-in chamfer Ll is in
Polyurethane TPU92, accordance with the table below:
Steel acc. to DIN 1624
H (mm) L1 (mm)
Area of application ≤ 9 1
Hydraulic and pneumatic systems,
10 1.4
reciprocal movements,
11 1.6
medium to heavy dirt load
12 1.8
14 2
Function
The WR ADM55 is a double function wiper. This
double function consists of wiping the dirt from Please also follow the general installation
the surface of the descending piston rod on the instructions.
one hand and on the other, that the remaining
oil film is retained and returned to the system Remarks
with the next descent. It is not necessary to drill In addition, we are able to supply other
a leakage hole if the seal is placed according dimensions required. For operational conditions
to the diagram. The metal angle ring with its outside the standard applications, other
additional press fit on the outer circumference, polyurethane materials and metals are
ensures the functionally correct fit of the wiper available.
in the housing. The high wear-resistance of
the polyurethane provides this wiper with a
particularly long service life.

Media
Hydraulic oils acc. to DIN 51524/ 51525,
lubricating oils, other mineral oil based fluids
and HFA, HFB, HFC highly non-flammable
hydraulic fluids acc. to VDMA 24317

89
WR ADM55
Dimensions in mm Dimensions in mm
Ø dN ØDN h=L H Ø dN ØDN h=L H
Sizes
metric

19 26 5 7 60 74 8 11
19 27 4 6 65 79 8 11
20 32 6 9 70 83 8 11
25 37 6 9 70 84 8 11
30 42 6 9 75 89 8 11
32 44 7 10 80 94 8 12
32 52 8 11 85 99 8 11
34 46 7 10 90 104 8 11
35 47 7 10 95 109 8 11
36 48 7 10 100 114 8 11
38 50 7 10 105 121 9 12
40 52 7 10 110 126 9 12
45 57 7 10 115 131 9 12
50 62 7 10 120 136 9 12
50 72 8 11 130 146 9 12
55 69 8 11 140 160 10 14

90
WR AD70

Two-piece double wiper consisting of a Installation


dynamic wiper ring and a static O-rin With small diameters, the wiper requires split
housing. With larger diameters, closed housing
Standard material can be planned. Dimension G and radius R are
Wiper: Polyurethane TPU98 given in the following table:
O-ring: Elastomer NBR70
L 3.7 5 6 8.4 11 14
Area of application
Hydraulic systems, G 1.5 1.5 1.5 2.0 2.0 2.5
reciprocal movements, R 0.4 0.8 1.0 1.2 1.5 2.0
medium dirt load
Please also follow the general installation
Function instructions.
The WR AD70 is a double function wiper with a
sharp wiping edge, a sealing lip on the medium Remarks
side and an O-ring as a energizing element. This In addition, we are able to supply other
double function consists of wiping the dirt from dimensions required. For operational conditions
the surface of the descending piston rod on the outside the standard applications, other
one hand and on the other, that the remaining polyurethane materials and metals are
oil film is retained and returned to the system available.
with the next descent. The high wear-resistance
of the polyurethane provides this wiper with a
particularly long service life.

Media
Hydraulic oils acc. to DIN 51524/ 51525,
lubricating oils, other mineral oil based fluids
and HFA, HFB, HFC highly non-flammable
hydraulic fluids acc. to VDMA 24317

Operational application limits


Temperature (°C): -30 to +100
Running speed (m/s): up to 2

91
WR AD70
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN L Ø dN ØDN L Ø dN ØDN L
Sizes
metric

6 10,8 3,7 56 62,8 5 190 198,8 6


8 12,8 3,7 57 63,8 5 200 208,8 6
10 14,8 3,7 60 66,8 5 205 213,8 6
12 18,8 5 63 69,8 5 210 218,8 6
14 20,8 5 64 70,8 5 220 228,8 6
15 21,8 5 65 73,8 6 230 238,8 6
16 22,8 5 70 78,8 6 235 243,8 6
18 24,8 5 72 80,8 6 240 248,8 6
20 26,8 5 75 83,8 6 250 258,8 6
22 28,8 5 80 88,8 6 254 266,2 8,4
24 30,8 5 85 93,8 6 260 272,2 8,4
25 31,8 5 90 98,8 6 270 282,2 8,4
28 34,8 5 92 100,8 6 280 292,2 8,4
30 36,8 5 95 103,8 6 290 302,2 8,4
32 38,8 5 100 108,8 6 300 312,2 8,4
33 39,8 5 104 112,8 6 310 322,2 8,4
34 40,8 5 105 113,8 6 320 332,2 8,4
35 41,8 5 106 114,8 6 350 362,2 8,4
36 42,8 5 110 118,8 6 360 372,2 8,4
38 44,8 5 115 123,8 6 370 382,2 8,4
40 46,8 5 120 128,8 6 400 412,2 8,4
41 47,8 5 125 133,8 6 440 456 11
42 48,8 5 127 135,8 6 465 481 11
43 49,8 5 130 138,8 6 472 488 11
45 51,8 5 135 143,8 6 480 496 11
48 54,8 5 140 148,8 6 550 566 11
50 56,8 5 150 158,8 6 680 700 14
52 58,8 5 160 168,8 6 750 770 14
54 60,8 5 170 178,8 6
55 61,8 5 180 188,8 6

92
WR AD71

Two-piece double wiper consisting of a Installation


dynamic wiper ring and a static O-ring With small diameters, the wiper requires split
housing. With larger diameters, closed housing
Standard material can be planned. Dimension G and radius R are
Wiper: Polyurethane TPU98 given in the following table:
O-ring: Elastomer NBR70
L 4.2 6.3 8.1 9.5 14 16
Area of application
Hydraulic systems, G 1.0 1.5 2.0 2.5 2.5 2.5
reciprocal movements, R 0.8 0.8 1.5 1.5 1.5 2.0
medium dirt load
Please also follow the general installation
Function instructions.
The WR AD71 is a double function wiper with a
sharp wiping edge, a sealing lip on the medium Remarks
side and an O-ring as a energizing element. This In addition, we are able to supply other
double function consists of wiping the dirt from dimensions required. For operational conditions
the surface of the descending piston rod on the outside the standard applications, other
one hand and on the other, that the remaining polyurethane compounds and O-rings made of
oil film is retained and returned to the system other elastomers are available.
with the next descent. The special shape of this
wiper makes it very robust and the high wear-
resistance of the polyurethane provides it with a
particularly long service life.

Media
Hydraulic oils ace. to DIN 51524/ 51525,
lubricating oils, other mineral oil based fluids
and HFA, HFB, HFC highly non-flammable
hydraulic fluids ace. to VDMA 24317

Operational application limits


Temperature (°C): -30 to +100
Running speed (m/s): up to 2

93
WR AD71
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN L Ø dN ØDN L Ø dN ØDN L
Sizes
metric

20 27,6 4,2 70 82,2 8,1 205 221 9,5


22 29,6 4,2 72 84,2 8,1 210 226 9,5
24 31,6 4,2 75 87,2 8,1 220 236 9,5
25 32,6 4,2 80 92,2 8,1 230 246 9,5
28 35,6 4,2 82 94,2 8,1 235 251 9,5
30 37,6 4,2 85 97,2 8,1 240 256 9,5
32 39,6 4,2 87 99,2 8,1 250 266 9,5
33 40,6 4,2 90 102,2 8,1 254 270 9,5
34 41,6 4,2 92 104,2 8,1 260 276 9,5
35 42,6 4,2 95 107,2 8,1 270 286 9,5
36 43,6 4,2 100 112,2 8,1 280 296 9,5
38 45,6 4,2 104 116,2 8,1 290 306 9,5
40 48,8 6,3 105 117,2 8,1 300 316 9,5
41 49,8 6,3 106 118,2 8,1 310 326 9,5
42 50,8 6,3 110 122,2 8,1 320 336 9,5
43 51,8 6,3 115 127,2 8,1 350 366 9,5
45 53,8 6,3 120 132,2 8,1 360 376 9,5
48 56,8 6,3 125 137,2 8,1 370 386 9,5
50 58,8 6,3 127 139,2 8,1 400 424 14
52 60,8 6,3 130 142,2 8,1 440 464 14
54 62,8 6,3 135 147,2 8,1 465 489 14
55 63,8 6,3 140 156 9,5 472 496 14
56 64,8 6,3 150 166 9,5 480 504 14
57 65,8 6,3 160 176 9,5 550 574 14
60 68,8 6,3 170 186 9,5 560 584 14
63 71,8 6,3 180 196 9,5 630 654 14
64 72,8 6,3 190 206 9,5 710 737,5 16
65 73,8 6,3 200 216 9,5 800 827,3 16

94
WR A80

Two-piece double wiper consisting of a Installation


dynamic wiper ring and a static O-ring With small diameters, the wiper requires split
housing. With larger diameters, closed housing
Standard material can be planned. Subsequent calibration
Wiper: PTFE/bronze is recommended. Radius R is given in the
O-ring: Elastomer NBR70 following table:

Area of application L 3.7 5 6 8.4 11 14


Hydraulic systems, R 0.4 0.8 1.0 1.2 1.5 2.0
reciprocal movements,
light dirt load Please also follow the general installation
instructions.
Function
The WR A80 is a single function wiper with an Remarks
O-ring as a energizing element. It is pressed In addition, we are able to supply other
against the descending piston rod wiping the dimensions required. For operational
dirt from the surface of the rod. The seals, their conditions outside the standard applications,
associated elements and the hydraulic medium other PTFE compounds and O-rings made
are protected from dirt. Due to the very good of other elastomers, such as FKM for higher
slide properties of PTFE, it is applied for short temperatures, are available.
strokes, high stroke speed and frequency. It is
not suitable for use with an extreme dirt load.

Media
Hydraulic oils acc. to DIN 51524/ 51525,
lubricating oils, other mineral oil based fluids
and HFA, HFB, HFC highly non-flammable
hydraulic fluids acc. to VDMA 24317

Operational application limits


Temperature (°C): -30 to +100
Running speed (m/s): up to 15

95
WR A80
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN L ØD2 Ø dN ØDN L ØD2 Ø dN ØDN L ØD2
Sizes
metric

12 18.8 5 15.5 60 66.8 5 63.5 200 208.8 6 204


14 20.8 5 17.5 63 69.8 5 66.5 205 213.8 6 209
15 21.8 5 18.5 64 70.8 5 67.5 210 218.8 6 214
16 22.8 5 19.5 65 73.8 6 69 220 228.8 6 224
18 24.8 5 21.5 70 78.8 6 74 230 238.8 6 234
20 26.8 5 23.5 72 80.8 6 76 235 243.8 6 239
22 28.8 5 25.5 75 83.8 6 79 240 248.8 6 244
25 31.8 5 28.5 80 88.8 6 84 250 258.8 6 254
28 34.8 5 31.5 85 93.8 6 89 260 272.2 8.4 264.5
30 36.8 5 33.5 90 98.8 6 94 270 282.2 8.4 274.5
32 38.8 5 35.5 92 100.8 6 96 280 292.2 8.4 284.5
33 39.8 5 36.5 95 103.8 6 99 290 302.2 8.4 294.5
34 40.8 5 37.5 100 108.8 6 104 300 312.2 8.4 304.5
35 41.8 5 38.5 104 112.8 6 108 310 322.2 8.4 314.5
36 42.8 5 39.5 105 113.8 6 109 320 332.2 8.4 324.5
38 44.8 5 41.5 106 114.8 6 110 350 362.2 8.4 354.5
40 46.8 5 43.5 110 118.8 6 114 360 372.2 8.4 364.5
41 47.8 5 44.5 115 123.8 6 119 370 382.2 8.4 374.5
42 48.8 5 45.5 120 128.8 6 124 400 412.2 8.4 404.5
43 49.8 5 46.5 125 133.8 6 129 440 456 11 445.2
45 51.8 5 48.5 130 138.8 6 134 465 481 11 470.2
48 54.8 5 51.5 135 143.8 6 139 472 488 11 477.2
50 56.8 5 53.5 140 148.8 6 144 480 496 11 485.2
52 58.8 5 55.5 150 158.8 6 154 550 566 11 555.2
54 60.8 5 57.5 160 168.8 6 164 600 616 11 605.2
55 61.8 5 58.5 170 178.8 6 174 680 700 14 686.6
56 62.8 5 59.5 180 188.8 6 184 750 770 14 756.6
57 63.8 5 60.5 190 198.8 6 194

96
WR AD60

Two-piece double wiper consisting of a Installation


dynamic wiper ring and a static O-ring With small diameters, the wiper requires split
housing. With larger diameters, closed housing
Standard material can be planned. Subsequent calibration is
Wiper: PTFE/bronze recommended. Dimension G and radius R are
O-ring: Elastomer NBR70 given in the following table:

Area of application L 3.7 5 6 8.4 11 14


Hydraulic systems,
reciprocal movements, G 1.5 1.5 1.5 2.0 2.0 2.5
light to medium dirt load R 0.4 0.8 1.0 1.2 1.5 2.0

Function Please also follow the general installation


The WR AD60 is a double function wiper with instructions.
a sharp wiper edge, a seal lip on the medium
side and an O-ring as a energizing element. This Remarks
double function consists of wiping the dirt from In addition, we are able to supply other
the surface of the descending piston rod on the dimensions required. For operational
one hand and on the other, that the remaining conditions outside the standard applications,
oil film is retained and returned to the system other PTFE compounds and O-rings made
with the next descent. Due to the very good of other elastomers, such as FKM for higher
slide properties of PTFE, it is applied for short temperatures, are available.
strokes, high stroke speed and frequency. It is
not suitable for use with an extreme dirt load.

Media
Hydraulic oils acc. to DIN 51524/ 51525,
lubricating oils, other mineral oil based fluids
and HFA, HFB, HFC highly non-flammable
hydraulic fluids acc. to VDMA 24317

Operational application limits


Temperature (°C): -30 to +100
Running speed (m/s): up to 15

97
WR AD60
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN L Ø dN ØDN L Ø dN ØDN L
Sizes
metric

6 10.8 3.7 56 62.8 5 190 198.8 6


8 12.8 3.7 57 63.8 5 200 208.8 6
10 14.8 3.7 60 66.8 5 205 213.8 6
12 18.8 5 63 69.8 5 210 218.8 6
14 20.8 5 64 70.8 5 220 228.8 6
15 21.8 5 65 73.8 6 230 238.8 6
16 22.8 5 70 78.8 6 235 243.8 6
18 24.8 5 72 80.8 6 240 248.8 6
20 26.8 5 75 83.8 6 250 258.8 6
22 28.8 5 80 88.8 6 254 266.2 8.4
24 30.8 5 85 93.8 6 260 272.2 8.4
25 31.8 5 90 98.8 6 270 282.2 8.4
28 34.8 5 92 100.8 6 280 292.2 8.4
30 36.8 5 95 103.8 6 290 302.2 8.4
32 38.8 5 100 lO8.8 6 300 312.2 8.4
33 39.8 5 104 112.8 6 310 322.2 8.4
34 40.8 5 105 113.8 6 320 332.2 8.4
35 41.8 5 106 114.8 6 350 362.2 8.4
36 42.8 5 110 118.8 6 360 372.2 8.4
38 44.8 5 115 123.8 6 370 382.2 8.4
40 46.8 5 120 128.8 6 400 412.2 8.4
41 47.8 5 125 133.8 6 440 456 11
42 48.8 5 127 135.8 6 465 481 11
43 49.8 5 130 138.8 6 472 488 11
45 51.8 5 135 143.8 6 480 496 11
48 54.8 5 140 148.8 6 550 566 11
50 56.8 5 150 158.8 6 680 700 14
52 58.8 5 160 168.8 6 750 770 14
54 60.8 5 170 178.8 6
55 61.8 5 l80 l88.8 6

98
WR AD61

Two-piece double wiper consisting of a Installation


dynamic wiper ring and a static O-ring With small diameters, the wiper requires split
housing. With larger diameters, closed housing
Standard material can be planned. Subsequent calibration
Wiper: PTFE/bronze is recommended. Dimension G and radius R are
O-ring: Elastomer NBR70 given in the following table:

Area of application L 4.2 6.3 8.1 9.5 14 16


Hydraulic systems,
reciprocal movements, G 1.0 1.5 2.0 2.5 2.5 2.5
light to medium dirt load R 0.8 0.8 1.5 1.5 1.5 2.0

Function Please also follow the general installation


The WR AD61 is a double function wiper with instructions.
a sharp wiper edge, a seal lip on the medium
side and an O-ring as a energizing element. This Remarks
double function consists of wiping the dirt from In addition, we are able to supply other
the surface of the descending piston rod on the dimensions required. For operational
one hand and on the other, that the remaining conditions outside the standard applications,
oil film is retained and returned to the system other PTFE compounds and O-rings made
with the next descent. The special shape of of other elastomers, such as FKM for higher
this wiper makes it very robust. Due to the very temperatures, are available.
good slide properties of PTFE, it is applied for
short strokes, high stroke speed and frequency.
It is not suitable for use with an extreme dirt
load.

Media
Hydraulic oils acc. to DIN 51524/ 51525,
lubricating oils, other mineral oil based fluids
and HFA, HFB, HFC highly non-flammable
hydraulic fluids acc. to VDMA 24317

Operational application limits


Temperature (°C): -30 to +100
Running speed (m/s): up to 15

99
WR AD61
Dimensions in mm Dimensions in mm Dimensions in mm
Ø dN ØDN L Ø dN ØDN L Ø dN ØDN L
Sizes
metric

20 27.6 4.2 70 82.2 8.1 205 221 9.5


22 29.6 4.2 72 84.2 8.1 210 226 9.5
24 31.6 4.2 75 87.2 8.1 220 236 9.5
25 32.6 4.2 80 92.2 8.1 230 246 9.5
28 35.6 4.2 82 94.2 8.1 235 251 9.5
30 37.6 4.2 85 97.2 8.1 240 256 9.5
32 39.6 4.2 87 99.2 8.1 250 266 9.5
33 40.6 4.2 90 102.2 8.1 254 270 9.5
34 41.6 4.2 92 104.2 8.1 260 276 9.5
35 42.6 4.2 95 107.2 8.1 270 286 9.5
36 43.6 4.2 100 112.2 8.1 280 296 9.5
38 45.6 4.2 104 116.2 8.1 290 306 9.5
40 48.8 6.3 105 117.2 8.1 300 316 9.5
41 49.8 6.3 106 118.2 8.1 310 326 9.5
42 50.8 6.3 110 122.2 8.1 320 336 9.5
43 51.8 6.3 115 127.2 8.1 350 366 9.5
45 53.8 6.3 120 132.2 8.1 360 376 9.5
48 56.8 6.3 125 137.2 8.1 370 386 9.5
50 58.8 6.3 127 139.2 8.1 400 424 14
52 60.8 6.3 130 142.2 8.1 440 464 14
54 62.8 6.3 135 147.2 8.1 465 489 14
55 63.8 6.3 140 156 9.5 472 496 14
56 64.8 6.3 150 166 9.5 480 504 14
57 65.8 6.3 160 176 9.5 550 574 14
60 68.8 6.3 170 186 9.5 560 584 14
63 71.8 6.3 180 196 9.5 630 654 14
64 72.8 6.3 190 206 9.5 710 737.5 16
65 73.8 6.3 200 216 9.5 800 827.3 16

100
Overview of
Hydraulic Ref. Pressure Temp. Speed Materials Dimensions Page
piston seals (bar) (°C) (m/s) metr. inch

Design

HPS K01 Piston seal 400 -30 0,5 NBR-impregnated ■ ■ 104


+100 fabric/
polyesterelastomer/
POM

HPS K03 Piston seal 400 -30 0,5 NBR/polyester- ■ ■ 106


+100 elastomer/POM

HPS K22 Piston seal 400 -30 0,5 NBR-impregnated ■ 108


+100 fabric/NBR/POM

HPS K25 Piston seal 700 -30 0,5 NBR-impregnated ■ ASK


+100 fabric/NBR/POM

HPS K14 Piston seal 400 -30 0,5 NBR/NBR-impregnated ■ ■ ASK


+100 fabric/POM

HPS K16 Piston seal 400 -30 0,5 NBR/NBR-impregnated ■ ■ ASK


+100 fabric/POM

HPS K15 Piston seal 40 -30 0,5 NBR80/metal ■ ASK


+100

HPS K17 Piston seal 60 -30 0,5 NBR90/metal ■ ASK


+100

HPS K30 Piston seal 400 -30 15 PTFE-Bronze- ■ ■ 110


+100 compound/NBR70

HPS K31 Piston seal 400 -30 15 PTFE-Bronze- ■ ■ 112


+100 compound/NBR70

102
Overview of
Hydraulic Ref. Pressure Temp. Speed Materials Dimensions Page
piston seals (bar) (°C) (m/s) metr. inch

Design

HPS K70 Piston seal 250 -­30 0,5 TPU95/NBR70 ■ ASK


+100

HPS K71 Piston seal 400 -­30 1,5 PTFE/NBR/POM ■ ASK


+100

HPS K753 Piston seal 400 ­-30 2 PTFE/NBR70 ■ ASK


+105

103
HPS K01

three-piece piston seal, consisting of a V-ring, Lead-in chamfer “C”


female adapter and support ring Seal section S 5 6 7,5 10 12,5
15
Lead-in chamfer C 3 4 5 5 6,5 7,5
Application
Hydraulic systems Surface finish
Surface roughness Ra R†
Material Dynamic sealing face ≤ 0,3 μm ≤ 3 μm
V-ring abrasion resistant NBR fabric Static sealing face ≤ 1,8 μm ≤ 10 μm
reinforced material Static housing faces ≤ 3 μm ≤ 16 μm
Female adapter Polyesterelastomer or
extremely high abrasion Installation
resistant material Split seal housing, i.e. multiple part
Support ring Polyacetal piston mounted with an axial clearance
(difference between “H” and “L”). The use of
Function hydraulicmedia suitable lubrications helps on
To use mainly for double acting piston - one installation and improves function ability when
packing set for each pressure side building up pressure.

Media Remarks
Hydraulic oils according to DIN 51524/51525 The sizes published in the table show the
Non-inflammable hydraulic fluids HFA, HFB, HFC standard range, permanently at stock, resp.
short-term available.
Operating conditions
Pressure (MPa/bar) 40/400 Further dimensions available on request.
Temperature (°C) -30 to +100
Speed (m/s) 0,5

104
HPS K01
Dimensions in mm Dimensions in mm Dimensions in mm
ØD Ød L H ØD Ød L H ØD Ød L H
Sizes
metric

20 10 9.3 8.9 50 35 11.5 11 115 95 21.2 20.6


22 12 9.3 8.9 55 40 11.5 11 125 100 25.8 25
25 15 9.3 8.9 56 41 11.5 11 140 115 25.8 25
28 18 9.3 8.9 60 45 11.5 11 150 120 29 28
32 20 10.9 10.4 63 48 13 12.5 160 130 29 28
35 23 10.9 10.4 70 50 15.2 14.6 180 150 31.5 30.5
36 24 10.9 10.4 80 60 15.2 14.6 200 170 33.5 32.5
40 25 11.5 11 90 70 21.2 20.6 250 220 33.5 32.5
42 27 11.5 11 100 80 21.2 20.6 300 270 33.5 32.5
45 30 11.5 11 110 90 21.2 20.6

105
HPS K03

five-piece packing set consisting of a sealing Lead-in chamfer “C”


ring, two support rings and two guide rings Seal section S ...8 ...10 ...12,5
Lead-in chamfer C 4 5 6
Application
Hydraulic systems Surface finish
Surface roughness Ra R†
Material Dynamic sealing face ≤ 0,3 μm ≤ 3 μm
Sealing ring NBR-Elastomer, 80 Shore A Static sealing face ≤ 1,8 μm ≤ 10 μm

Support rings Polyesterelastomer Static housing faces ≤ 3 μm ≤ 16 μm

Guide rings Polyacetal


Installation
Easy to mount on an one-piece piston.
Function
Double acting, good sealing performance also Remarks
at low pressure, piston guidance. The sizes published in the table show the
standard range, permanently at stock, resp.
Media short-term available.
Hydraulic oils according to DIN 51524/51525
Non-inflammable hydraulic fluids HFA, HFB, HFC Further dimensions available on request.

Operating conditions
Pressure (MPa/bar) 40/400
Temperature (°C) -30 to +100
Speed (m/s) 0,5
Parameter is valid for piston with axial support of
the guide ring.

106
HPS K03
Dimensions in mm Dimensions in mm Dimensions in mm
ØD Ød L L1 Ø d2 ØD Ød L L1 Ø d2 ØD Ød L L1 Ø d2
Sizes
metric

20 11 13.5 2.1 17 63.5 47.62 19.05 6.35 58.9 140 115 25.4 9.52 132.1
22 13 13.5 2.1 19 63.5 53.97 11.1 3.81 59.12 140 115 25.4 6.35 133
25 15 12 4 21 65 49 20.5 3.1 61 140 118 26.5 5.1 136
25 15 12.5 4 22 65 50 18.4 6.35 60.41 140 120 25 6.35 135
25 15 16.4 6.35 21.45 70 50 22.4 6.35 64.2 140 123 26.5 7.2 136
25 16 13.5 2.1 22 70 54 20.5 3.1 66 145 120 25.4 9.52 137.6
25 17 10 4 22 70 55 20 5 66 145 120 25.4 6.35 138.3
25 17 13.5 3.2 21 70 58 20.5 4.2 66 150 125 25.4 9.5 142.6
28 19 13.5 2.1 25 75 55 22.4 6.35 69.2 150 125 25.4 6.35 143
30 17 15.4 6.35 26.5 75 59 20.5 3.1 71 150 128 26.5 5.1 146
30 21 13.5 2.1 27 76.2 57.15 23.81 6.35 70.38 150 130 25.4 6.35 144.1
30 22 13.5 3.2 26 80 60 22.4 6.35 74.15 150 133 26.5 7.2 146
32 22 12.5 4 29 80 60 25 6.35 75 152.4 127 31.75 9.52 145
32 22 15.5 2.6 28 80 62 22.5 3.6 76 155 130 25.4 9.52 147.6
32 22 16.4 6.35 28.5 80 65 20 5 76 155 130 25.4 6.35 148
32 24 10 4 29 80 66 22.4 5.2 76 160 130 25.4 9.52 152.6
32 24 15.5 3.1 28 85 65 22.4 6.35 79.15 160 130 25.4 6.35 153
35 25 16.4 6.35 31.4 85 75 20 4 81 160 135 25.4 9.52 152.6
35 27 15.5 3.2 31 88.9 69.85 24.81 6.35 83.08 160 135 32 10 154
40 24 18.4 6.35 35.4 90 70 22.4 6.35 84.15 160 138 26.5 5.1 156
40 26 15.5 2.6 36 90 72 22.5 3.2 86 160 140 25 6.35 155
40 30 12.5 4 37 90 75 20 5 86 160 143 26.5 7.2 156
40 30 16.4 6.35 35.4 90 76 22.4 5.2 86 165 140 25.4 9.52 157.6
40 32 10 4 37 95 75 22.4 6.35 89.15 170 145 25.4 12.7 161.72
40 32 15.5 3.2 36 100 75 22.4 6.35 93.13 170 148 26.5 5.1 166
42 28 15.5 2.6 38 100 80 25 6.3 95 175 150 25.4 12.7 166.7
44.45 28.57 19.05 6.35 39.85 100 80 25.4 6.35 95 177.8 152.4 31.75 9.52 170.51
45 29 18.4 6.35 40.4 100 82 22.5 3.6 96 180 150 35.4 6.35 172.95
45 31 15.5 2.6 41 100 85 20 5 96 180 155 25.4 12.7 171.72
45 35 16.4 6.35 40.4 100 86 22.4 5.2 96 180 158 26.5 5.1 176
45 37 15.5 3.2 41 101.6 82.55 23.81 6.35 95.76 180 163 26.5 7.2 176
50 34 18.4 6.35 45.4 105 80 22.4 6.5 98.1 185 160 25.4 12.7 176.72
50 34 20.5 3.1 46 110 85 22.4 6.35 103.1 190 165 25.4 12.7 181.72
50 35 20 5 46 110 85 25.4 6.35 103.1 195 170 25.4 12.7 187.1
50 38 20.5 4.2 46 110 90 25.3 9.52 102.6 200 170 35.4 6.35 193
50 40 12.5 4 47 110 90 25.4 6.4 104.1 200 170 36 6.35 192
50.8 34.92 19.05 6.35 46.23 110 92 22.5 3.6 106 200 175 25.4 12.7 191.62
50.8 41.27 11.1 3.81 46.27 110 95 20 5 105 200 175 31.5 6.6 196
55 39 18.4 6.35 50.37 110 96 22.4 5.2 106 200 180 31.5 9.2 196
55 39 20.5 3.1 51 114.3 88.9 31.75 6.35 107.42 210 185 25.4 12.7 201.62
55 45 12.5 4 52 115 90 22.4 6.35 108.1 220 190 35.4 6.35 212.7
56 40 20.5 3.1 52 115 97 22.4 4.2 111 220 195 25.4 12.7 211.6
57.15 41.27 19.45 6.35 52.55 120 95 22.4 6.35 113.1 220 200 31.5 9.2 216
60 44 18.4 6.35 55.4 120 106 22.4 5.2 116 225 200 25.4 12.7 216.62
60 44 20.5 3.1 56 125 100 25.4 6.35 118.1 230 205 25.4 12.7 221.62
60 48 20.5 4.2 56 125 100 32 6.35 118.1 240 215 25.4 12.7 231.62
60.32 44.45 19.05 6.35 55.72 125 103 26.5 5.1 121 250 220 35.4 6.35 242.9
63 47 18.4 6.35 58.39 125 105 25 6.35 119.1 250 225 25.4 12.7 241.62
63 47 19.4 6.35 58.4 125 105 25.4 6.35 120 250 230 31.5 9.2 246
63 47 20.5 3.1 59 125 108 26.5 7.2 121 280 250 35.4 9.52 272.9
63 48 20 5 59 130 105 25.4 6.35 123.1 280 250 36.4 10 273
63 51 20.5 4.2 59 135 110 25.4 9.52 127.6
63 53 12.5 4 60 139.7 114.3 31.75 9.52 132.41

107
HPS K22

three-piece piston seal consisting of a sealing Lead-in chamfer “C”


ring and two guide rings Seal section S ...8 ...10 ...12,5
Lead-in chamfer C 4 5 6
Application
Hydraulic systems Surface finish
Surface roughness Ra R†
Material Dynamic sealing face ≤ 0,3 μm ≤ 3 μm
Sealing ring NBR-Elastomer fabric Static sealing face ≤ 1,8 μm ≤ 10 μm
reinforced on Static housing faces ≤ 3 μm ≤ 16 μm
the sealing surface

Guide rings Polyamid Installation


Easy to mount on an one-piece piston.
Function
Double acting, good sealing performance also Remarks
at low pressure, piston guidance. The sizes published in the table show the
standard range, permanently at stock, resp.
Media short-term available.
Hydraulic oils according to DIN 51524/51525
Non-inflammable hydraulic fluids HFA, HFB, HFC Further dimensions available on request.

Operating conditions
Pressure (MPa/bar) 40/400
Temperature (°C) -30 to +100
Speed (m/s) 0,5
Parameter is valid for piston with axial support of
the guide ring.

108
HPS K22
Dimensions in mm Dimensions in mm Dimensions in mm
ØD Ød Ø d1 L L1 ØD Ød Ø d1 L L1 ØD Ød Ø d1 L L1
Sizes
metric

45 37 41 15.5 3.2 90 76 86 22.5 5.2 160 140 156 25 7.2


50 38 46 20.5 4.2 100 86 96 22.5 5.2 160 143 156 26.5 7.2
60 48 56 20.5 4.2 110 96 106 22.5 5.2 180 163 176 26.5 7.2
70 58 66 20.5 4.2 120 106 116 22.5 5.2 200 180 196 31.5 9.2
75 63 71 20.5 4.2 125 108 121 26.5 7.2 220 200 216 31.5 9.2
80 66 76 22.5 5.2 140 123 136 26.5 7.2 250 230 246 31.5 9.2
85 71 81 22.5 5.2 150 133 146 26.5 7.2

109
HPS K30

is a two-piece piston seal consisting of a Media


dynamic sealing ring and a static O-ring. Hydraulic oils, lubricating oils and other mineral
oil based fluids
Area of application
Hydraulic systems, reciprocating movements Operational application limits
Pressure (MPa/bar) 40/400
Standard materials Temperature (°C) -30 to +100
Sealing ring PTFE/bronze compound Running speed (m/s) up to 15

O-ring Elastomer NBR70


Installation
With small diameters, the seal requires split
Function housing. With larger diameters, closed housing
The HPS K30 is a double acting piston seal. can be planned. Subsequent calibration is
Its design provides an exceptionally good recommended.
sealing function with high loads and very good
static tightness. Various ranges are available. Remarks
Whereas the standard series covers general The sizes mentioned on the following pages
demands, the heavy duty series represent the standard dimensions. They are
provides for extreme conditions with abrupt always in stock or can be delivered at short
loading, high pressure and changing pressures. notice. In addition, we are able to supply other
The light duty series does not require much dimensions required. For operational conditions
housing space and is used when only a small other than the standard applications, further
space is available. The thickness of the seal PTFE compounds and O-rings made of other
section in the various series is adaptable to elastomers are available.
requirement. The cross section of the elastomer
O-ring is changed correspondingly.
Independent of the size of the gap, it is
necessary to centre the piston using suitable
guidings and taking up the radial power load.

110
HPS K30
Dimensions in mm Dimensions in mm Dimensions in mm
ØD Ød L ØD Ød L ØD Ød L
Sizes
metric

8 3.1 2.2 78 67 4.2 190 174.5 6.3


10 5.1 2.2 80 59 8.1 200 179 8.1
11 6.1 2.2 80 64.5 6.3 210 189 8.1
12 7.1 2.2 80 69 4.2 210 194.5 6.3
14 9.1 2.2 82 71 4.2 215 194 8.1
15 7.5 3.2 85 64 8.1 220 199 8.1
16 8.5 3.2 85 69.5 6.3 230 209 8.1
16 11.1 2.2 88 72.5 6.3 240 219 8.1
18 10.5 3.2 89 73.5 6.3 250 229 8.1
20 12.5 3.2 90 69 8.1 260 239 8.1
20 15.1 2.2 90 74.5 6.3 270 249 8.1
22 14.5 3.2 95 74 8.1 280 259 8.1
24 16.5 3.2 95 79.5 6.3 290 269 8.1
25 17.5 3.2 95 84 4.2 300 279 8.1
25 20.1 2.2 100 79 8.1 300 284.5 6.3
27 19.5 3.2 100 84.5 6.3 310 289 8.1
28 17 4.2 105 84 8.1 320 299 8.1
28 20.5 3.2 105 89.5 6.3 330 305.5 8.1
28 23.1 2.2 106 90.5 6.3 340 315.5 8.1
30 22.5 3.2 110 89 8.1 350 325.5 8.1
32 24.5 3.2 110 94.5 6.3 360 335.5 8.1
32 27.1 2.2 112 96.5 6.3 370 345.5 8.1
34 26.5 3.2 115 94 8.1 380 355.5 8.1
35 27.5 3.2 115 99.5 6.3 390 365.5 8.1
36 28.5 3.2 120 99 8.1 400 375.5 8.1
38 30.5 3.2 120 104.5 6.3 410 385.5 8.1
39 31.5 3.2 120 109 4.2 420 395.5 8.1
40 29 4.2 125 104 8.1 430 405.5 8.1
40 32.5 3.2 125 109.5 6.3 440 415.5 8.1
42 31 4.2 125 114 4.2 450 425.5 8.1
43 32 4.2 127 111.5 6.3 460 435.5 8.1
44 33 4.2 130 109 8.1 470 445.5 8.1
45 34 4.2 130 114.5 6.3 480 455.5 8.1
48 37 4.2 132 111 8.1 490 465.5 8.1
50 34.5 6.3 133 112 8.1 500 475.5 8.1
50 39 4.2 135 114 8.1 510 485.5 8.1
52 41 4.2 135 119.5 6.3 520 495.5 8.1
52 44.5 3.2 138 117 8.1 530 505.5 8.1
54 43 4.2 140 119 8.1 540 515.5 8.1
55 39.5 6.3 140 124.5 6.3 550 525.5 8.1
55 44 4.2 145 124 8.1 560 535.5 8.1
56 45 4.2 150 129 8.1 570 545.5 8.1
60 44.5 6.3 154 133 8.1 580 555.5 8.1
60 49 4.2 155 134 8.1 590 565.5 8.1
62 51 4.2 160 139 8.1 600 575.5 8.1
63 47.5 6.3 160 144.5 6.3 610 585.5 8.1
63 52 4.2 165 144 8.1 620 595.5 8.1
64 53 4.2 170 149 8.1 630 605.5 8.1
65 54 4.2 170 154.5 6.3 640 615.5 8.1
70 54.5 6.3 175 154 8.1 650 625.5 8.1
70 59 4.2 180 159 8.1 660 635.5 8.1
75 59.5 6.3 180 164.5 6.3
75 64 4.2 190 169 8.1

111
HPS K31

is a two-piece piston seal consisting of a Media


dynamic sealing ring and a static a-ring. Hydraulic oils, lubricating oils and other mineral
oil based fluids
Area of application
Hydraulic systems, reciprocating movements Operational application limits
Pressure (MPa/bar) 40/400
Standard materials Temperature (°C) -30 to +100
Sealing ring PTFE/bronze compound Running speed (m/s) up to 15

O-ring Elastomer NBR70


Installation
With small diameters, the seal requires split
Function housing. With larger diameters, closed housing
The HPS K31 is a single acting piston seal. The can be planned. Subsequent calibration is
special design provides an exceptionally good recommended.
sealing function as well as smooth running and
accurate positioning. Remarks
Various ranges are available. Whereas the The sizes mentioned on the following page
standard series covers general demands, represent the standard dimensions. They are
the heavy duty series provides for extreme always in stock or can be delivered at short
conditions with abrupt loading, high pressure notice. In addition, we are able to supply other
and changing pressures. The light duty series dimensions required. For operational conditions
does not require much housing space and other than the standard applications, further
is used when only a small space is available. PTFE compounds and O-rings made of other
The thickness of the seal section in the various elastomers are available.
series is adaptable to requirement. The cross
section of the elastomer a-ring is changed
correspondingly. Independent of the size of the
gap, it is necessary to centre the piston using
suitable guidings taking up the radial power
load.

112
HPS K31
Dimensions in mm Dimensions in mm Dimensions in mm
ØD Ød L ØD Ød L ØD Ød L
Sizes
metric

8 3.1 2.2 80 64.9 6.3 310 286 8.1


10 5.1 2.2 85 69.9 6.3 320 296 8.1
12 7.1 2.2 90 74.9 6.3 330 306 8.1
15 10.1 2.2 95 79.9 6.3 340 316 8.1
16 11.1 2.2 100 84.9 6.3 350 326 8.1
18 10.7 3.2 105 89.9 6.3 360 336 8.1
20 12.7 3.2 110 94.9 6.3 370 346 8.1
22 14.7 3.2 115 99.9 6.3 380 356 8.1
22 17.1 2.2 120 104.9 6.3 390 366 8.1
24 16.7 3.2 125 109.9 6.3 400 376 8.1
25 17.7 3.2 130 114.9 6.3 410 386 8.1
25 20.1 2.2 135 119.9 6.3 420 396 8.1
28 17.3 4.2 140 124.9 6.3 430 406 8.1
28 20.7 3.2 145 129.9 6.3 440 416 8.1
30 22.7 3.2 150 134.9 6.3 450 426 8.1
30 19.3 4.2 155 139.9 6.3 460 436 8.1
32 21.3 4.2 160 144.9 6.3 470 446 8.1
35 24.3 4.2 165 149.9 6.3 480 456 8.1
36 25.3 4.2 170 154.9 6.3 490 466 8.1
38 27.3 4.2 175 159.9 6.3 500 476 8.1
39 28.3 4.2 180 164.9 6.3 510 486 8.1
40 29.3 4.2 190 174.9 6.3 520 496 8.1
42 31.3 4.2 200 179.5 8.1 530 506 8.1
45 34.3 4.2 210 189.5 8.1 540 516 8.1
48 37.3 4.2 220 199.5 8.1 550 526 8.1
50 39.3 4.2 225 204.5 8.1 560 536 8.1
52 41.3 4.2 230 209.5 8.1 570 546 8.1
55 44.3 4.2 240 219.5 8.1 580 556 8.1
60 44.9 6.3 250 229.5 8.1 590 566 8.1
60 49.3 4.2 260 236 8.1 600 576 8.1
63 47.9 6.3 270 246 8.1 610 586 8.1
65 49.9 6.3 275 254 8.1 620 596 8.1
70 54.9 6.3 280 256 8.1 630 606 8.1
70 59.3 4.2 290 266 8.1 640 616 8.1
75 59.9 6.3 300 276 8.1 650 626 8.1

113
Overview of
Hydraulic rod Ref. Pressure Temp. Speed Materials Dimensions Page
seals (bar) (°C) (m/s) metr. inch

Design

HRS S01 Rod seal 400 -30 0,5 NBR-impregnated ■ ■ 116


+100 fabric/
NBR/
polyesterelastomer/
POM

HPRS S05 Piston/Rod 200 -30 0,5 NBR/NBR-impregnated ■ ■ 118


seal +100 fabric

HRS S07 Rod seal 400 -30 0,5 NBR/NBR-impregnated ■ 120


+100 fabric/POM

HRS S12 Rod seal 700 -30 0,5 NBR/NBR-impregnated ■ ■ ASK


+100 fabric/POM

HRS S30 Rod seal 400 -30 15 PTFE-Bronze- ■ ■ 123


+100 compound/NBR70

HRS S31 Rod seal 400 -30 15 PTFE-Bronze- ■ ■ 125


+100 compound/NBR70

HRS S72 Rod seal 400 -­30 0,5 TPU92/POM ■ ASK


+100

HRS S73 Rod seal 400 ­ -40 0,5 TPU95/POM ■ ASK


+100

HRS S150 Rod seal 400 ­-30 0,5 SP.NBR/FAB ■ ASK


+100

114
Overview of
Hydraulic rod Ref. Pressure Temp. Speed Materials Dimensions Page
seals (bar) (°C) (m/s) metr. inch

Design

HRS S151 Rod seal 250 -­30 2 SP.NBR/FAB/ ■ ASK


+80 POM/PTFE

HRS S152 Rod seal 80 -­ 30 1 SP.NBR/FAB ■


+80 ASK

HRS S153 SP.NBR/FAB/POM

115
HRS S01

Veepac rod seal, consisting of five V-rings, one Lead-in chamfer “C”
support ring and one female adapter Seal section S ...6 7,5...10 12,5...15
Lead-in chamfer C 3 5 7,5
Application
Hydraulic systems Surface finish
Heavy duty applications Surface roughness Ra R†
Dynamic sealing face ≤ 0,3 μm ≤ 3 μm
Material Static sealing face ≤ 1,8 μm ≤ 10 μm
V-rings 3 V-rings fabric reinforced Static housing faces ≤ 3 μm ≤ 16 μm
material
2 V-rings NBR-Elastomer
Installation
Female adapter Polyesterelastomer or Easy to mount in split seal housings. The use
extremely high abrasion of lubrications improves function ability and
resistant material
durability when building up pressure. Also to be
Support ring Polyacetal mounted in common adjustable housings.

Function Remarks
Single acting, excellent performance even The sizes published in the table show the
under difficult operating conditions. standard range, permanently at stock, resp.
short-term available.
Media
Hydraulic oils according to DIN 51524/51525 Further dimensions available on request.
Non-inflammable hydraulic fluids HFA, HFB, HFC

Operating conditions
Pressure (MPa/bar) 40/400
Temperature (°C) -30 to +100
Speed (m/s) 0,5

116
HRS S01
Dimensions in mm Dimensions in mm Dimensions in mm
ØD Ød H=L ØD Ød H=L ØD Ød H=L
Sizes
metric

8 18 18.5 40 55 22.5 85 105 40


10 20 18.5 42 54 22.5 90 105 22.5
12 22 18.5 42 57 22.5 90 110 40
14 24 18.5 45 60 22.5 100 115 30
15 25 18.5 45 65 22.5 100 120 40
16 26 18.5 50 65 22.5 105 125 40
18 28 18.5 50 70 30 105 130 40
20 30 18.5 55 70 22.5 110 125 30
20 32 22.5 55 75 30 110 130 40
22 32 18.5 56 71 22.5 115 130 30
22 34 22.5 56 76 37 115 140 46
25 37 22.5 60 75 22.5 125 140 34
25 40 22.5 60 80 37 125 150 46
28 40 22.5 63 78 22.5 135 160 40
28 43 22.5 63 83 37 140 155 34
30 42 22.5 65 80 22.5 140 165 46
30 45 22.5 65 85 40 150 170 40
32 44 22.5 70 85 22.5 150 180 60
32 47 22.5 70 90 40 160 180 40
35 47 22.5 75 90 22.5 160 190 60
35 50 22.5 75 95 40 180 200 40
36 48 22.5 80 95 22.5 180 210 60
36 51 22.5 80 100 40 200 220 40
40 52 22.5 85 100 22.5 200 230 60

117
HPRS S05

one-piece rod seal Surface finish


Surface roughness Ra R†
Application Dynamic sealing face ≤ 0,3 μm ≤ 3 μm
Hydraulic systems Static sealing face ≤ 1,8 μm ≤ 10 μm
Static housing faces ≤ 3 μm ≤ 16 μm
Material
NBR-Elastomer reinforced on the back. Extrusion gap “G”
When used with an exceeding operating
Function pressure or a wider gap “G” a support ring will
Single acting compact rod seal. be suitable.
Good sealing performance also at low pressure,
to be used also for single acting piston. Pressure MPa 10 16 20
Extrusion gap Gmax. 0,2 0,15 0,1
Media
Hydraulic oils according to DIN 51524/51525 Installation
Non-inflammable hydraulic fluids HFA, HFB, HFC Seals of 20 mm diameter and above can be
mounted in an one-piece seal housing. Below
Operating conditions 20 mm and for piston sealing a split housing is
Pressure (MPa/bar) 20/200 required.
Temperature (°C) -30 to +100
Speed (m/s) 0,5 Remarks
The sizes published in the table show the
Lead-in chamfer “C” standard range, permanently at stock, resp.
Seal section S ...4 4...6 6...7,5 short-term available.
Lead-in chamfer C 2,5 3 5
Further dimensions available on request.

118
HPRS S05
Dimensions in mm Dimensions in mm Dimensions in mm
Ød ØD L H Ød ØD L H Ød ØD L H
Sizes
metric

6.35 19.05 6.35 6 31.75 47.62 7.93 60 70 12.5 12.2


7.93 15.87 6.35 6 31.75 47.62 11.11 10.31 60 72 9.5 9.2
9.52 15.87 4.76 31.75 47.62 12.7 11.7 60 80 14 13.7
9.52 19.05 7.14 6.84 32 40 5.5 5.2 63 75 9
9.52 22.22 6.35 6 32 40 6 5.7 63.5 76.2 7.93
10 17 6.3 6 32 40 9 8.6 65 77 9
12 19 6.3 5.8 34.92 44.45 7.14 6.84 65 80 11 10.7
14 22 6.3 6 35 43 6 5.7 65 85 14 13.7
15 23 6.3 6 35 45 6.5 6.2 69.85 82.55 9.52 8.73
15 25 7.5 7.2 35 45 7.5 7.2 70 80 7.5 7.2
15 27 6.5 6.2 35 50 12 11.7 70 82 9 8.7
16 24 6.5 6.2 36 44 6.3 6 70 84 12 11.7
18 26 6.5 6.2 38 44 5 70 85 8 7.7
19.05 31.75 9.52 8.73 38 50 9 70 85 11.5
20 27 6.5 6.2 38.1 50.8 9.52 8.73 75 85 7.5 7.2
20 28 6.3 6 38.1 53.97 12.83 75 85 9
20 28 7 6.7 40 48 6 75 87 9.3 9
20 32 10 9.7 40 50 7 6.7 75 95 14 13,7
20.63 34.92 12.7 11.7 40 50 10.5 10 76,2 88,9 9,52 8,73
22 30 6.5 6.2 40 55 7.5 7.2 76.2 95.25 12.7 11.7
22 32 6 5.7 40 60 10 9.7 80 90 7.5 7.2
22 32 10 9.7 42 50 6 5.7 80 92 9 8.7
22 35 9.5 9.2 45 55 8 7.7 80 95 12.5
25 32 6 45 55 9 80 96 10 9.7
25 33 6 45 55 10.5 10.2 80 100 14 13.7
25 35 8.5 8.2 45 57 9.5 9.2 85 95 7.5 7.2
25 44 12 11.7 45 60 12 11.7 85 97 9
25.4 31.75 4.76 46.04 76.2 25.4 88.9 114.3 12.7 11.7
25.4 34.92 6.35 6 47.62 57.15 7.14 6.84 90 102 9
25.4 38.1 9.52 8.73 47.62 63.5 11.11 10.31 90 110 12.5 12.2
25.4 41.27 11.11 10.31 48 60 10 9.7 95 105 11 10.5
26 40 9.5 9.2 48 60 10.5 10.2 95 107 12 11.7
28 36 6.3 6 50 58 12.5 12.2 100 115 12 11.7
28.57 34.92 4.76 50 60 10 9.7 100 120 14 13.7
28.57 41.27 9.52 8.73 50 62 9 107.95 133.35 19.05
28.57 42.86 7.93 50 70 14 13.7 110 125 11 10.7
30 38 6 5.7 50.8 66.67 11.11 10.31 110 125 12 11.7
30 38 7 6.7 53.97 69.85 9.52 8.73 110 130 12 11.7
30 40 7 6.7 55 65 7.5 7.2 114.3 139.7 19.05
30 40 7.5 7.2 55 70 10 9.7 120 130 10.5 10.2
30 45 10.5 10.2 56 66 7.5 7.2 123 133 7.5 7.2
30.16 42.86 7.93 57.15 69.85 9.52 8.73 125 140 11.5
30.16 42.86 9.52 8.73 57.15 76.2 14.28 13.49 130 145 9
31.75 38.1 4.76 60 70 7.5 7.2 140 150 10.5 10.2
31.75 41.27 7.14 6.84 60 70 9

119
HRS S07

two-piece rod seal consisting of one sealing ring Lead-in chamfer “C”
and one support ring Seal section S ...4 4...6 6...7,5
Lead-in chamfer C 2.5 3 5
Application
Hydraulic systems Surface finish
Surface roughness Ra R†
Material Dynamic sealing face ≤ 0,3 μm ≤ 3 μm
Sealing ring NBR-Elastomer reinforced on Static sealing face ≤ 1,8 μm ≤ 10 μm
the back Static housing faces ≤ 3 μm ≤ 16 μm
Support ring Polyacetal
Extrusion gap “G”
Function Pressure MPa 16 25 40
Single acting compact rod seal, good sealing Extrusion gap G max 0,4 0,3 0,2
performance also at low pressure.
Installation
Media For seals up to 20 mm diameter and for the
Hydraulic oils according to DIN 51524/51525 dimensions marked with * a split seal housing
Non-inflammable hydraulic fluids HFA, HFB, HFC is required. In all other cases an one-piece
housing can be used. Support rings up to 100
Operating conditions mm diameter have to be split for mounting.
Pressure (MPa/bar) 40/400
Temperature (°C) -30 to +100 Remarks
Speed (m/s) 0,5 The sizes published in the table show the
standard range, permanently at stock, resp.
short-term available.

Further dimensions available on request.

120
HRS S07
Dimensions in mm Dimensions in mm Dimensions in mm
ØD Ød L H ØD Ød L H ØD Ød L H
Sizes
metric

6 14 6.5 6.2 34.92 50.8 8.5 8.2 55 65 7.5 7.2


8 16 6 5.7 35 43 6 5.7 55 65 8 7.7
12 23 7.5 7.2 35 45 6.5 6.2 55 65 10.5 10.2
15 27 6.5 6.2 35 45 7.5 7.2 55 65 13 12.7
15 27 7 6.7 35 45 10 9.7 55 70 10 9.7
16 22 5 4.7 35 45 10.5 10.2 55 70 10.5 10.2
16 24 6.5 6.2 35 50 10.5 10.2 55 75 14 13.7
16 24 7 6.7 35 50 11.5 11.2 * 55 75 14.5 14.2
16 28 7.5 7.2 36 43 6 5.7 56 71 10 9.7
18 26 6.4 6 36 43 6.5 6.2 56 71 10.5 10.2
18 28 5.8 5.5 36 44 6.4 6.1 56 76 14 13.7
18 28 6.3 6 36 46 8 7.7 56 76 14.5 14.2
18 30 7.5 7.2 36 46 8.5 8.2 57.15 69.85 10 9.7
20 27 6 5.7 36 48 9 8.7 60 69.5 7 6.7
20 28 5.8 5.5 36 48 9.5 9.2 60 70 8 7.7
20 28 6.3 6 36 48 12 11.7 60 70 9.5 9.2
20 28 6.4 6.1 38.1 50.8 10 9.7 60 70 10.5 10.2
20 28 7 6.7 38.1 53.97 10.5 10.2 60 70 11 10.7
20 30 8 7.7 40 48 6 5.7 60 70 12.5 12.2
20 30 8.5 8.2 40 48 6.5 6.2 60 70 13 12.7
20 32 9 8.7 40 50 7.5 7.2 60 72 9.5 9.2
20 35 11 10.7 40 50 8 7.7 60 72 10 9.7
22 28 6.5 6.2 40 50 8.5 8.2 60 75 12.5 12.2
22 30 6.5 6.2 40 50 10 9.7 60 75 13 12.7
22 30 7 6.7 40 50 10.5 10.2 60 80 14 13.7
22 32 10 9.7 40 50 11 10.7 * 60 80 14.5 14.2
22 34 9 8.7 40 52 9 8.7 63 75 10.5 10.2
22 34 9.5 9.2 40 52 10.5 10.2 63 75 11 10.7
22 35 10 9.7 40 55 7.5 7.2 63 78 10 9.7
25 33 6 5.7 40 55 8 7.7 63 78 12.5 12.2
25 33 6.4 6.1 40 55 10.5 10.2 63 83 14 13.7
25 35 8 7.7 40 55 11 10.7 63 83 14.5 14.2
25 35 9 8.7 40 60 7.5 7.2 63.5 76.2 8.5 8.2
25 38 9.5 9.2 40 60 10 9.7 63.5 77.78 11.5 11.2
25 38 10 9.7 40 60 10.5 10.2 63.5 82.55 14.28 13.98
25.4 31.75 4.76 4.46 40 60 14 13.7 65 75 13 12.7
25.4 34.92 6.35 6.05 * 40 60 14.5 14.2 65 75 13.5 13.2
25.4 38.1 10 9.7 42 52 9 8.7 65 77 9.6 9.3
25.4 38.1 11.11 10.81 44.45 53.97 7.62 7.32 65 80 11 10.7
28 36 6.4 6.1 44.45 60.32 11.6 11.3 65 80 11.5 11.2
28 38 8 7.7 45 53 10.5 10.2 65 80 12 11.7
28 40 9 8.7 45 55 7.5 7.2 65 80 12.5 12.2
28 40 9.5 9.2 45 55 8 7.7 65 85 14 13.7
28 41 10 9.7 45 55 10.5 10.2 70 80 8 7.7
28.57 39.68 9.25 8.95 45 57 10 9.7 70 80 12.5 12.2
28.57 44.45 11.11 10.81 45 60 10 9.7 70 80 13 12.7
30 38 6.5 6.2 45 60 10.5 10.2 70 82 10.5 10.2
30 40 7 6.7 45 63 10.5 10.2 70 84 12.5 12.2
30 40 7.5 7.2 45 65 10.5 10.2 70 85 12 11.7
30 40 10 9.7 45 65 14 13.7 70 85 12.5 12.2
30 40 10.5 10.2 45 65 14.5 14.2 70 90 14 13.7
30 42 10 9.7 48 60 10.5 10.2 75 85 11 10.7
30 45 9 8.7 50 60 7.5 7.2 75 85 12 11.7
30 50 14 13.7 50 60 8 7.7 75 90 11 10,7
* 30 50 14.5 14.2 50 60 10 9.7 75 90 11,5 11,2
31.75 38.1 6.35 6.05 50 60 10.5 10.2 75 90 12,8 12,5
31.75 41.27 7.14 6.84 50 62 10 9.7 75 95 14 13,7
31.75 47.62 11.6 11.3 50 65 10.5 10.2 75 95 14,5 14,2
32 40 8.5 8.2 50 65 11 10.7 80 90 12.5 12.2
32 40 9 8.7 50 70 14 13.7 80 93 14.5 14.2
32 42 8 7.7 * 50 70 14.5 14.2 80 95 12 11.7
32 42 11 10.7 50.8 63.5 9.52 9.22 80 95 12.5 12.2
32 45 9.5 9.2 50.8 69.85 15.87 15.57 80 96 10 9.7
32 45 10 9.7 54 66 9.5 9.2 80 96 10.5 10.2

121
HRS S07
Dimensions in mm Dimensions in mm Dimensions in mm
ØD Ød L H ØD Ød L H ØD Ød L H
Sizes
metric

80 100 12 11.7 105 120 15 14.7 140 155 13 12.7


80 100 14 13.7 105 125 12 11.7 140 160 12 11.7
80 100 14.5 14.2 105 125 12.5 12.2 140 160 12.5 12.2
82.55 101.6 12.7 12.4 110 120 10.5 10.2 140 160 14 13.7
85 95 8 7.7 110 125 11.5 11.2 140 160 14.5 14.2
85 100 12 11.7 110 125 12 11.7 140 170 22.8 22.5
85 105 14.3 14 110 130 12 11.7 145 157.7 10 9.7
85 105 14.5 14.2 110 130 12.5 12.2 150 170 14 13.7
88.9 114.3 19.5 19.2 110 135 15 14.7 150 170 14.5 14.2
90 100 10.5 10.2 110 135 15.5 15.2 160 175 16 15.7
90 105 9.5 9.2 115 135 15.5 15.2 160 180 14 13.7
90 105 12.5 12.2 120 130 10.5 10.2 160 180 14.5 14.2
90 106.2 10.8 10.5 120 130 12.5 12.2 165 185 16 15.7
90 110 12.5 12.2 120 132.7 10 9.7 175 200 23 22.7
90 110 14 13.7 120 135 12.5 12.2 180 200 14 13.7
95 105 10.5 10.2 120 140 12 11.7 180 200 14,5 14,2
95 105 11 10.7 120 140 12.5 12.2 180 210 20.5 20.2
95 107 12.5 11.9 120 145 18.8 18.5 190 210 14.5 14.2
95 112 12 11.7 121.2 150 14 13.7 198 208 12 11.7
95 115 14 13.7 125 150 14 13.7 200 220 14 13.7
95 115 14.5 14.2 125 150 14.5 14.2 200 220 14.5 14.2
100 115 11.5 11.2 130 145 12.5 12.2 210 240 22.5 22.2
100 115 12 11.7 130 145 13 12.7 220 250 20.5 20.2
100 115 12.5 12.2 130 145 15 14.7 230 260 20.5 20.2
100 120 11.5 11.2 130 150 15.5 15.2 530 570 25 24.7
100 120 12 11.7 130 150 16 15.7 640 680 25 24.7
100 120 14 13.7 135 150 14 13.7 760 820 35 34.7
100 120 14.5 14.2 135 160 13.5 13.2 845 905 35 34.7
105 115 11 10.7 135 160 14 13.7

122
HRS S30

is a two-piece rod seal consisting of a dynamic Media


sealing ring and a static O-ring. Hydraulic oils, lubricating oils and other mineral
oil based fluids
Area of application
Hydraulic systems, reciprocating movements Operational application limits
Pressure (MPa/bar) 40/400
Standard materials Temperature (°C) -30 to +100
Sealing ring PTFE/bronze compound Running speed (m/s) up to 15

O-ring Elastomer NBR70


Installation
With small diameters, the seal requires split
Function housing. With larger diameters, closed housing
The HRS S30 is a double acting rod seal. can be planned. Subsequent calibration is
It is preferably used for short strokes of high recommended.
frequency and under high pressu¬re loads. To
counteract the minimal permeability which Remarks
occasionally occurs under extreme pressure The sizes mentioned on the following page
conditions, it is advisable to use, in succession, a represent the standard dimensions. They are
combination of HRS S30 as the primary and always in stock or can be delivered at short
HRS S31 as a secondary seal. Various ranges notice. In addition, we are able to supply other
are available. Whereas the standard series dimensions required. For operational conditions
covers general demands, the heavy duty other than the standard applications, further
series provides for extreme conditions with PTFE compounds and O-rings made of other
abrupt loading, high pressure and changing elastomers are available.
pressures. The light duty series does not require
much housing space and is used when only a
small space is available. The thickness of the
seal section in the various series is adaptable
to require¬ment. The cross section of the
elastomer O-ring is changed correspondingly. It
is advisable to install a double wiper ring so that
the remaining oil film is removed from the rod
and returned to the system. Independent of the
size of the gap, it is necessary to centre the rod
using suitable guidings and taking up the radial
power load.

123
HRS S30
Dimensions in mm Dimensions in mm Dimensions in mm
Ød ØD L Ød ØD L Ød ØD L
Sizes
metric

6 10.9 2.2 60 75.1 6.3 310 334 8.1


7 11.9 2.2 63 78.1 6.3 320 344 8.1
8 12.9 2.2 65 80.1 6.3 330 354 8.1
8 15.3 3.2 70 85.1 6.3 340 364 8.1
10 14.9 2.2 75 90.1 6.3 350 374 8.1
10 17.3 3.2 80 95.1 6.3 360 384 8.1
12 16.9 2.2 82 97.1 6.3 370 394 8.1
12 19.3 3.2 85 100.1 6.3 380 404 8.1
14 18.9 2.2 90 105.1 6.3 390 414 8.1
14 21.3 3.2 95 110.1 6.3 400 424 8.1
16 23.3 3.2 100 115.1 6.3 410 434 8.1
18 25.3 3.2 105 120.1 6.3 420 444 8.1
20 27.3 3.2 110 125.1 6.3 430 454 8.1
20 30.7 4.2 115 130.1 6.3 440 464 8.1
22 29.3 3.2 120 135.1 6.3 450 474 8.1
22 32.7 4.2 125 140.1 6.3 460 484 8.1
25 32.3 3.2 130 145.1 6.3 470 494 8.1
25 35.7 4.2 135 150.1 6.3 480 504 8.1
28 38.7 4.2 140 155.1 6.3 490 514 8.1
30 37.3 3.2 150 165.1 6.3 500 524 8.1
30 40.7 4.2 160 175.1 6.3 510 534 8.1
32 42.7 4.2 170 185.1 6.3 520 544 8.1
35 45.7 4.2 180 195.1 6.3 530 554 8.1
36 46.7 4.2 190 205.1 6.3 540 564 8.1
40 50.7 4.2 200 220.5 8.1 550 574 8.1
40 55.1 6.3 210 230.5 8.1 560 584 8.1
42 52.7 4.2 220 240.5 8.1 570 594 8.1
45 55.7 4.2 230 250.5 8.1 580 604 8.1
45 60.1 6.3 240 260.5 8.1 590 614 8.1
48 58.7 4.2 250 270.5 8.1 600 624 8.1
50 60.7 4.2 260 284 8.1 610 634 8.1
50 65.1 6.3 270 294 8.1 620 644 8.1
55 70.1 6.3 280 304 8.1 630 654 8.1
56 71.1 6.3 290 314 8.1 640 664 8.1
60 70.7 4.2 300 324 8.1 650 677.3 9.5

124
HRS S31

is a two-piece rod seal consisting of a dynamic Media


sealing ring and a static O-ring. Hydraulic oils, lubricating oils and other mineral
oil based fluids
Area of application
Hydraulic systems, reciprocating movements Operational application limits
Pressure (MPa/bar) 40/400
Standard materials Temperature (°C) -30 to +100
Sealing ring PTFE/bronze compound Running speed (m/s) up to 15

O-ring Elastomer NBR70


Installation
With small diameters, the seal requires split
Function housing. With larger diameters, closed housing
The HRS S31 is a single acting rod seal. It is can be planned. Subsequent calibration is
particularly suitable for extreme loads and is recommended.
usually doubled. The special shape of its sealing
lip guarantees sufficient lubricating of the Remarks
gap on the one hand and prevents disruptive The sizes mentioned on the following pages
intermediate pressure from building up on the represent the standard dimensions. They are
other. Various ranges are available. Whereas always in stock or can be delivered at short
the standard series covers general demands, notice. In addition, we are able to supply other
the heavy duty series provides for extreme dimensions required. For operational conditions
conditions with abrupt loading, high pressure other than the standard applications, further
and changing pressures. The light duty series PTFE compounds and O-rings made of other
does not require much housing space and elastomers are available.
is used when only a small space is available.
The thickness of the seal section in the various
series is adaptable to requirement. The cross
section of the elastomer O-ring is changed
correspondingly. It is advisable to install a
double wiper ring so that the remaining oil film
is removed from the rod and returned to the
system. Independent of the size of the gap, it
is necessary to centre the rod using suitable
guidings and taking up the radial power load.

125
HRS S31
Dimensions in mm Dimensions in mm Dimensions in mm
Ød ØD L Ød ØD L Ød ØD L
Sizes
metric

4 8.9 2.2 42 52.7 4.2 135 150.1 6.3


5 9.9 2.2 42 57.1 6.3 140 155.1 6.3
6 10.9 2.2 43 58.5 6.3 140 155.5 6.3
6 11 2.2 45 55.7 4.2 145 160.1 6.3
7 11.9 2.2 45 56 4.2 145 165.5 8.1
8 12.9 2.2 45 60.1 6.3 150 165.1 6.3
8 13 2.2 48 58.7 4.2 150 170.5 8.1
8 15.3 3.2 48 61.3 6.3 155 170.1 6.3
10 14.9 2.2 50 60.7 4.2 160 175.1 6.3
10 15 2.2 50 61 4.2 160 175.5 6.3
10 17.3 3.2 50 65.1 6.3 160 180.5 8.1
12 16.9 2.2 52 62.7 4.2 160 181 8.1
12 17 2.2 52 67.1 6.3 165 180.1 6.3
12 19.3 3.2 55 65.7 4.2 170 185.1 6.3
12 19.5 3.2 55 70.1 6.3 175 190.1 6.3
14 18.9 2.2 56 66.7 4.2 180 195.1 6.3
14 19 2.2 56 67 4.2 180 195.5 6.3
14 21.3 3.2 56 71.1 6.3 180 200.5 8.1
14 21.5 3.2 56 71.5 6.3 180 201 8.1
15 19.9 2.2 58 73.1 6.3 190 205.1 6.3
15 22.3 3.2 60 70.7 4.2 198 213.1 6.3
16 20.9 2.2 60 75.1 6.3 200 220.5 8.1
16 23.3 3.2 63 73.7 4.2 200 221 8.1
16 23.5 3.2 63 74 4.2 210 230.5 8.1
18 22.9 2.2 63 78.1 6.3 220 240.5 8.1
18 25.3 3.2 63 78.5 6.3 220 241 8.1
18 25.5 3.2 65 80.1 6.3 225 245.5 8.1
20 27.3 3.2 67 82.1 6.3 230 250.5 8.1
20 27.5 3.2 70 80.7 4.2 240 255.5 6.3
20 30.7 4.2 70 85.1 6.3 240 260.5 8.1
20 31 4.2 70 85.5 6.3 250 270.5 8.1
22 29.3 3.2 75 85.7 4.2 250 271 8.1
22 29.5 3.2 75 90.1 6.3 260 284 8.1
22 32.7 4.2 80 90.7 4.2 270 294 8.1
22 33 4.2 80 95.1 6.3 280 304 8.1
24 34.7 4.2 80 95.5 6.3 280 304.5 8.1
25 32.3 3.2 85 95.7 4.2 290 314 8.1
25 32.5 3.2 85 100.1 6.3 300 324 8.1
25 35.7 4.2 90 100.7 4.2 310 334 8.1
25 36 4.2 90 105.5 6.3 320 344 8.1
26 36.7 4.2 90 105.1 6.3 320 344.5 8.1
28 35.3 3.2 92 107.1 6.3 330 354 8.1
28 38.7 4.2 95 110.1 6.3 340 364 8.1
28 39 4.2 97 112.1 6.3 350 374 8.1
30 37.3 3.2 100 110.7 4.2 360 384 8.1
30 40.7 4.2 100 115.1 6.3 360 384.5 8.1
32 39.3 3.2 100 115.5 6.3 370 390.5 8.1
32 42.7 4.2 105 120.1 6.3 370 394 8.1
32 43 4.2 108 123.1 6.3 380 404 8.1
35 42.3 3.2 110 120.7 4.2 390 414 8.1
35 45.7 4.2 110 125.1 6.3 400 420.5 8.1
36 43.3 3.2 110 125.5 6.3 400 424 8.1
36 46.7 4.2 115 130.1 6.3 410 434 8.1
36 47 4.2 120 135.1 6.3 420 444 8.1
38 48.7 4.2 125 140.1 6.3 430 454 8.1
38 53.1 6.3 125 140.5 6.3 440 464 8.1
40 50.7 4.2 130 140.7 4.2 450 474 8.1
40 51 4.2 130 145.1 6.3 455 479 8.1
40 55.1 6.3 130 150.5 8.1 460 484 8.1

126
HRS S31
Dimensions in mm Dimensions in mm Dimensions in mm
Ød ØD L Ød ØD L Ød ØD L
Sizes
metric

470 494 8.1 540 564 8.1 610 634 8.1


480 504 8.1 550 574 8.1 620 644 8.1
490 514 8.1 560 584 8.1 630 654 8.1
500 524 8.1 570 594 8.1 640 664 8.1
510 534 8.1 580 604 8.1 650 677.3 9.5
520 544 8.1 590 614 8.1
530 554 8.1 600 624 8.1

127
Overview of
Guide strips Ref. Pressure Temp. Speed Materials Dimensions Page
(bar) (°C) (m/s) metr. inch
Design

GS FUB01 Guide strip -60 15 PTFE-compounds ■ ■ ASK


Piston-/Rod +200

GS FUB02 Piston/Rod ­ -50 1 polyester-based ■ ■ ASK


130 fabric laminate

GRR FUR01 Rod guide -60 15 PTFE-compounds ■ ■ ASK


ring +200

GRP FUR02 Piston guide -60 15 PTFE-compounds ■ ■ ASK


ring +200

GRR FUR03 Rod guide -40 0,5 POM-Glas-compound ■ ■ ASK


ring +130

GRP FUR04 Piston guide -40 0,5 POM-Glas-compound ■ ■ ASK


ring +130

GRR FUR05 Rod guide -50 0,5 polyester-based ■ ■ ASK


ring +130 fabric laminate

GRP FUR06 Piston guide -50 0,5 polyester-based ■ ■ ASK


ring +130 fabric laminate

128
PTFE seals Modern hydraulic and pneumatic systems The pressure of the medium to be sealed on
are now substantially smaller in their the O-ring results in perfectly spread sealing
design and also markedly more efficient. surface pressure provided by the radially
This advancement can, in essence, be positioned contact pressure on the PTFE
attributed to the highly¬developed seal ring. In this manner, the total sealing strength
technology. is always as great as is necessary for the
pressure required.
Hubata Seals’s PTFE piston and rod seals fulfil
all demands. Their compact construction The structural shapes of Hubata Seals’s
is suitable not only for standard but also for Sand K series, the PTFE compounds and
specific seal housings. They continue to gain types of elastomer are diverse and variable.
in market importance due to their special However, their applications and surrounding
advantages - space-saving construc¬tion, conditions have certain limitations due to
long life as well as good physical, chemical their combination with elastomer O-rings.
and mechanical properties . PTFE’s material
mix recipe and our special processing Spring energized
guarantee outstanding quality which cannot With applications where elastomer loses
be achieved with conventionally produced its effectiveness, for example at very high
PTFE materials. or very low temperatures, incompatibility
with the medium, etc., spring energized
■■ Exceptional pressure resistance with
PTFE seals, e.g. those in the Hubata Seals
optimal gap extrusion resistance, minor
MA series, are better suited. The functional
development of frictional heat and
principle is similar to that described above.
minimal wear resistance.
The mechanical preload and durable
■■ Extremely positive characteristics ¬no elasticity are achieved by a metal spring
stick slip differing stroke speeds, even integrated in the lip seal.
during a single cycle and with extremely
slight movements .
The material of the metal spring is
■■ Chemical stability against almost all determined by the medium used and the
media, as well as total lack of leakage structural shape by the spring force required.
with regard to media viscosity and its Standard equipment for Hubata Seals’s PTFE
hydrodynamic dragging behaviour. seals are springs made of non-corrosive,
acid-resistant steel no. 1.4310. When even
■■ Dependable functioning in high
higher medium stability is demanded, highly
temperature, speed and pressure areas.
alloyed ELGILOY® stainless steel is used.

Elastomer ring energized There are two kinds of spring to choose


An assembled seal contains two from. Springs with a V shape have a slightly
components: one dynamic sealing ring increasing spring characteristic with great
made of PTFE compound as the primary deformation capacity and are used
seal and a static elastomer O-ring as the most frequently. Springs with an H shape
secondary seal. The func¬tion is based command rapidly increasing spring force
on an approved system whereby the within a small deformation area.
installation actuated O-ring statically seals
in the groove bed and presses the dynamic Spring energized PTFE seals are more
sealing PTFE ring on to the counter surface. efficient than those supported by elastomer
The energized O-ring offers even during the rings and thereby complete the broad
unpressurized state a certain preload so to range of applications covered by Hubata
allow the pressure to be build up in working Seals’s PTFE seals to maximum effect.
condition.

130
PTFE seals Material Material Hardness Application
Energizing elements Descr. acc. to Shore A temperature range °C
ISO 1629
Type

O-ring NBR Acrylonitrile-butadiene rubber 70 -30 / +120


FKM Fluorinated rubber 80 -20 / +205
EPDM Ethylene-propylene-diene elastomer 70 -40 / +130

Metal springs – non-corrosive, acid resistant – -150 / +250


No.: 1.4310
®
ELGILOY

Schematic graph of
the spring force

131
Notes and Although PTFE is a highly efficient and ■■ Tips of screws, grooves for guide rings,
robust seal material, it is still necessary to etc. should be covered because the
instructions on seal should not be pushed over gaps,
be particularly careful when installing a
installation PTFE seal to prevent damaging the sealing drillings or rough surfaces.

lip which would result in leakage even ■■ Dust, dirt, chips and other foreign
before being put into service. The following particles must be carefully removed.
instructions should be followed for safe
installation:
■■ Cylinders, rods and seals must be
greased or oiled before installation,
■■ Installation of the seal must take place giving consideration to compatibility
with the preloaded side facing the with the medium.
direction of pressure. Particular care
■■ A PTFE seal expands and reverts to its
must be taken with compact seals as
original shape a great deal more easily
the preloaded side is possibly not easy
if it is heated in oil or hot water (approx.
to recognize.
80°–120°).
■■ It is imperative to have lead-in chamfers
■■ Any tools used for installation, e.g.
on the cylinder and on the rod. You will
cones and mandrels for expansion or
find the recommended lengths and
calibration, should be made of soft
angles in the installation dimension
material and not have any sharp edges.
information for the different seals.

■■ Sharp edges must be deburred and


radii and chamfering must be done
according to the installation dimension
information.

Smallest possible size of seals Series no.


able to be installed in axially 000 001 002 003 004
closed seal housings in mm

Seal type

HPS K04 > 14 > 25 > 60 – –

HPS K23 > 12 > 14 > 25 > 46 > 75

HPS K30 > 14 > 18 > 25 > 45 > 80

HPS K31 > 14 > 18 > 25 > 45 > 75

RDO WDA32 > 16 > 20 > 25 > 45 > 75

HPS MA44 > 35 > 50 > 70 > 100 > 135

HRS S04 > 10 > 25 > 60 – –

HRS S23 >8 > 12 > 20 > 40 > 120

HRS S30 >10 > 12 > 15 > 32 > 70

HRS S31 > 12 > 15 > 20 > 38 > 70

WR AD60 – > 28 > 35 > 40 > 75

RDI WDI32 > 16 > 20 > 25 > 45 > 75

HRS MA43 > 32 > 68 > 105 > 290 > 450

For smaller nominal sizes than mentioned


above, split seal housings must be provided.

132
Installing piston seals in Insert the O-ring flat in the groove Reversion of the stretched PTFE ring is
a closed groove (not twisted). facilitated with a calibrating mandrel whose
inner diameter matches the diameter of the
Slide the PTFE ring over a conical installation cylinder.
tool using an expanding mandrel until it
snaps into the groove. The ring is expanded
in the process.

Installing rod seals in a Insert the O-ring flat in the groove Insert the compressed PTFE ring in the
closed groove (not twisted). groove.

Press the PTFE ring together in a kidney Calibrate using a mandrel.


shape ensuring that no sharp bends are
formed.

133
Housings Seals play a very decisive role in the Provision must also always be made for
functioning of hydraulic or pneumatic sufficient guiding of the piston and rod. The
cylinders; they are the weakest link and fit of the guiding rings also has a decisive
subjected to attacks of a varied nature. influence on the functional safety of seals.
Selection of the appropriate seal is They should, therefore, be placed close to
determined with regard to imper¬viousness, the guide ring.
media compatability and temperature
resistance, friction, wear resistance, stroke Wipers prevent any foreign particles, which
frequency as well as service life. For this could destroy the seals, from getting into
reason, great care should be taken when the medium system of a hydraulic cylinder.
determining the metal slide face, the metal Additionally, when using double wipers, the
gap on the side opposite the pressure, the oil film left by the seal is retained and led
groove, the piston and rod guide as well as back into the closed system when the rod
the wiper. To ensure trouble-free operation, descends again. To keep the plant clean
the measurements given for the size and and protect the environment against oil
type of seal, angle and curves should be pollution, no hydraulic cylinder should be
adhered to. used without a wiper or, better still, a double
wiper.
Rounded corners in the groove bed (1)
ensure that the O-ring lies correctly and
rounded flanks of the groove’s edges (2)
minimize the risk of the seal moving into the
metal gap. Suitable surface finishes of the
groove bed (3) as well as the groove flanks
(4), adherance to the tolerances for the
groove width (5), the lead-in chamfers (6)
and the size of the seal gap (7), as well as
the surface finish of the opposed surface (8),
all have a decisive influence on the service
life of the seal.

134
Table
PTFE seals Ref. Movements Speed Pressure Temp.
(m/s) (bar) (°C)

Design

Rod seal

HRS S06 2 160 -30 to +100


-20 to+205 *

HRS S23 15 350 -30 to +100


-20 to+205 *

HRS S30 15 400 -30 to +100


-20 to+205 *

HRS S31 15 400 -30 to +100


-20 to+205 *

HRS MA43 15 350 -150 to+250

Piston seal

HPS K04 2 160 -30 to +100


-20 to+205 *

HPS K23 15 350 -30 to +100


-20 to+205 *

HPS K30 15 400 -30 to +100


-20 to+205 *

HPS K31 15 400 -30 to +100


-20 to+205 *

HPS MA44 15 350 -150 to+250

* with FKM O-ring 135


Table
PTFE seals Ref. Movements Speed Pressure Temp.
(m/s) (bar) (°C)

Design

Wipers

WR AD60 15 - -30 to +100


-20 to+205 *

Guide rings

GS FUB01 15 - -60 to +200

GRR FUR01 15 - -60 to +200

GRP FUR02 15 - -60 to +200

Rotary seals

RS WEPO 15 10 -20 to +205

RDI MA47 15 350 -150 to+250

RDI WDI32 5 300 -30 to +100


-20 to+205 *

RDO WDA32 5 300 -30 to +100


-20 to+205 *

Static seals

FSO MA45 - 800 -150 to+250

FSI MA46 - 800 -150 to+250 *


with FKM
O-ring

136 * with FKM O-ring


HEAD OFFICE
18, Rozhen blvd.; 1220 Sofia, Bulgaria
tel.: +359 2 8378 499, 8378 599
fax: +359 2 8376 599
office.sofia@hubata-seals.com

OFFICE PLOVDIV
8, Peshtersko shouse blvd.; 4002 Plovdiv, Bulgaria
tel.: +359 32 640 654
fax: +359 32 640 654
office.plovdiv@hubata-seals.com

www.hubata-seals.com

HS.2011.09-02

Potrebbero piacerti anche