Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Electrical Specifications
Power Ring Film Capacitor™ ESL: Less than 5 nH in a suitable
SBE Part #: 700D10896-348
1000 µF, 600 VDC laminar bus structure
Capacitance/Tolerance: 1000 µF ±10%
Operating Temperature: -40°C to +85°C at full
DC Voltage Rating: 600 Vdc DC voltage rating
Electrical Specifications
Dielectric/Construction: Metallized polypropylene. Voltage, Temperature De-rate voltage linearly to
Part #:
SBE Single section design
700D10896-348
De-rating: 400 Vdc from +85°C to +105°C
Capacitance/Tolerance:
Dielectric Withstand: 1000Units
µF ±10%
100% tested at DC
Voltage Rating:
DC 600potential
VDC of 750 Volts for two System Fault Current 10,000 Amps maximum
Dielectric/Construction:
minutes at 25°C Rating
Metallized Polypropylene. Single section design, (external
non-inductively to the
wound
capacitor):
Dielectric Withstand: Unit shall withstand a DC potential of 750 Volts for two minutes
500
1.5
Maximum Ripple Current (A rms)
ESR, milliohms
1 300
200
0 0
0.01 0.1 1 10 100 1000 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105
2. The capacitor can handle extreme current for small duty ratios. Trise occurs very slowly. This is
because the capacitor has a high specific heat.
5. For 200 ARMS the assumed 10°C internal Trise is very conservative based on simulation results
and verification measurements.
30
29
28
27
Mechanical Specifications
26
Dimensions: Refer to layout details
Terminals: Tin plated copper, 25
0.032” thick 0 2000 4000 6000 8000
Encapsulation: Molded polymer case, Time in seconds
potted with RTV
Marking:
SBE SBE company identification Mechanical Specifications
700D348 SBE “short form” part number Dimensions: Refer to layout details
1000 µF ±10% Capacitance value and Terminals: Nickel plated copper, 0.032” thick
tolerance Encapsulation: Polycarbonate outer housing, potted with RTV silicone
600 Vdc DC voltage rating Marking: SBE SBE Company Identification
yyww-lot#-unit 12-digit serial number (date 700D348 SBE Part Number
code, lot number, unit number) 1000 μF ±10% Capacitance value and tolerance
600 VDC DC Voltage Rating
yyww Weekly date code (i.e. 0915 = 15th week of 2009)
Mechanical Mounting and Additional Thermal Notes: that the capacitor internal heating is VERY small, and
other bus structure heat sources are very likely signifi-
This capacitor is optimized for extremely low self cantly higher than the heat added to the bus by the
inductance when connected to a suitable laminar bus capacitor. Capacitor dissipation is approximately 5W at
structure. When so connected, the capacitor is very 200Arms, from 1-100KHz. It is highly recommended to
rigidly attached to such a structure and thus does not use infrared thermal imaging from a system cold start
necessarily need to be mounted to a chassis. However, to determine the location and relative magnitude of
the capacitor case can be attached to an application thermal input to the bus. The capacitor may well func-
surface/heat sink, etc. if desired. When so mounted, tion as a thermal conduit for bus structure heat, and
the capacitor can be part of the bus structure sup- it will be very possible that the capacitor internal hot
port. Use of thermal interface compound between the spot is less than the terminal temperature.
capacitor case and application surface/heat sink will Thermal contour maps are available for some repre-
assist with removal of capacitor and bus heat. Note sentative conditions.
Layout Details:
Revisions
NOTES:
REV. DESCRIPTION CHG CHK APR DATE
BY BY BY
1. All Hole Positions Inspected
2. All Dimensions Inspected Unless 01 Initial Release - - - -
Marked As Reference 02 Standardized Layout View AGH MGS MSB 12/14/2010
7X 45.0°
22.5°
6.868 C
Bolt Circle
A 16X M5X0.8 - 6H THRU
28 in-lbs MAX Torque
.020 A B C
8.746
Bolt Circle
8.465
4X .197±.005 THRU .040
Accepts 1/4" Plastite Screw 16 Surfaces
9.252 40 in-lbs MAX Torque
.020 M A B C .260
Bolt Circle
2.154
A
1.000
NON-TOLERANCED DIMENSIONS ARE BASIC
.500 SBE, INC.
.663 .010 A B C 81 PARKER ROAD
.280 UNLESS OTHERWISE SPECIFIED:
BARRE, VT 05641 USA
ALL DIMENSIONS ARE IN INCHES 802.476.4146 FAX: 802.661.3950
TITLE
Power Ring Capacitor,
GEOMETRIC TOLERANCING PER: Y14.5-2009
1000uF, 600VDC
DRAWN MGS
DETAIL A CHECKED DMB 11/12/2010
DWG. NO.
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF SBE. ANY
SCALE 1 : 1
ENG APPR. MSB 11/12/2010 700D348LV
REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF SBE IS PROHIBITED. MATERIAL FINISH SIZE REV
DO NOT SCALE DRAWING A 02 SHEET 1 OF 1
Lowest available ESR, less than 150 micro-Ohms typical Figure 2 shows the “stacked” inverter design after the
Crown terminal architecture provides for a multitude integration of the ring capacitor and the laminar bus
of current paths which allows the monolithic capacitor plate. By now combining both aspects of vertical inte-
to function as a distributed element with a much lower gration and the low temperature rise characteristics
ESR than an equivalent array of smaller parts. SBE has of the capacitors, an increase to 50% or more volume
#SBE-PR-348-01/11
developed a next generation capacitor simulation tool reduction is realistically possible. These improvements
that allows accurate calculation of hotspot tempera- clearly translate into weight and cost reductions.
ture to allow optimal rating with excellent reliability.