Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
AD1404013CE
Remote
SA-BTT405PH
SB-HC4010 Control
SC-BTT405P
SC-BTT405PH
SB-HFS4010 SA-BTT405 SB-HW4010
Colour:(K)...........Black Type
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general
public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting
to service a product. Products powered by electricity should be serviced or repaired only by experienced professional
technicians. Any attempt to service or repair the product or products dealt with in this service information by anyone else
could result in serious injury or death.
2
3
Examples of typical ES devices are IC(integrated circuits)and some field-effect transistors and
semiconductor “chip” components.
The following techniques should be used to help reduce the incidence of component damage caused by electrostatic
discharge(ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on
your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD
wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)"
can generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it.
(Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or
comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective
material to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)
sufficient to damage an ES device).
4
CAUTION :
This product utilizes a laser diode with the unit turned “on”,
invisible laser radiation is emitted from the pick-up lens.
Wave length:770 to 800 nm (CDs)/645 to 660 nm (DVDs)
Maximum output radiation power from pick-up:100 μW/
VDE Laser radiation from the pick-up lens is safety level,
but be sure the followings:
1. Do not disassemble the optical pick-up unit, since
radiation from exposed laser diode is dangerous.
2. Do not adjust the variable resistor on the pick-up unit, it
was already adjusted.
3. Do not look at the focus lens using optical instruments.
4. Recommend not to look at pick-up lens for a long time.
om e er orm e
r o e ro e Manufactured
o ev o r er No e January 2014 (Example)
N0.50 e e 24 200 .
CAUTION !
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
5
6
Yes No
anuals of the hub or router.
OK
connect to any wireless network for
RETURN
usage rights.
may be regarded as illegal
DO NOT DISCONNECT the unit from the AC
ing online on your PC after
tings on this unit, perform thepower or perform any operation while the update
ur PC. is in process.
onnecting to a network without 7
After the firmware is installed, “FIn” will be
n the leaking of data such as
displayed on the unit’s display. Unit will restart
and the following screen will be displayed.
Downloaded from www.Manualslib.com manuals search engine
The firmware was updated.
3.2.2.2. Updating firmware using the USB device
When using the USB device to update the firmware.
(When using CD-R instead of USB device, perform same the procedures)
1.Download the latest firmware file of the unit.
The latest firmware required for version-up can be downloaded from “Support Information from NWBG/VDBG PAVC”web-
sitein “TSN system”.
Click file name to download.
After download, click file to decompress. (Total: 1 file).
2.Decompress the downloaded file.
The decompressed file will be named as follows.
File Name: PANA_HTS.FRM
Copy the file to root diretory of the USB device.
(If using CD-R instead of USB device, burn the file to a blank CD-R by a writing software.)
3.Update the unit.
1.Tunr the unit power on.
2. After the home screen is displayed and appears at LED display of the front panel,insert the USB device stored
downloaded latest firmware file to the front USB port of the unit(LED display change to ).(or insert the CD-R into
the unit and playback it.)
3.TV will show the firmware Update UI automatically and is displayed at LED display.
8
6.Turn the unit on and the home screen appears the firmware update is completed.
9 9
“AVCHD” is a trademark of Panasonic Corporation and Sony Copyright 2004-2013 Verance Corporation. CinaviaTM is a Verance
Corporation. Corporation trademark. Protected by U.S. Patent 7,369,677 and
worldwide patents issued and pending under license from Verance
Java is a registered trademark of Oracle and/or its affiliates. Corporation. All rights reserved.
Manufactured under license from Dolby Laboratories. This product incorporates the following software:
Dolby, Pro Logic, and the double-D symbol are trademarks of (1) the software developed independently by or for Panasonic
Dolby Laboratories. Corporation,
(2) the software owned by third party and licensed to Panasonic
For DTS patents, see http://patents.dts.com. Manufactured under
Corporation,
license from DTS Licensing Limited. DTS, DTS-HD, the Symbol, &
(3) the software licensed under the GNU General Public License,
DTS and the Symbol together are registered trademarks, and
Version 2.0 (GPL V2.0),
DTS-HD Master Audio | Essential is a trademark of DTS, Inc. ©
(4) the software licensed under the GNU LESSER General Public
DTS, Inc. All Rights Reserved.
License, Version 2.1 (LGPL V2.1), and/or
HDMI, the HDMI Logo, and High-Definition Multimedia Interface (5) open source software other than the software licensed under
are trademarks or registered trademarks of HDMI Licensing LLC in the GPL V2.0 and/or LGPL V2.1.
the United States and other countries. The software categorized as (3) - (5) are distributed in the hope
that it will be useful, but WITHOUT ANY WARRANTY, without
This product is licensed under the AVC patent portfolio license and even the implied warranty of MERCHANTABILITY or FITNESS
VC-1 patent portfolio license for the personal and non-commercial FOR A PARTICULAR PURPOSE. Please refer to the detailed
use of a consumer to (i) encode video in compliance with the AVC terms and conditions thereof shown in the Settings menu.
Standard and VC-1 Standard (“AVC/VC-1 Video”) and/or (ii)
decode AVC/VC-1 Video that was encoded by a consumer At least three (3) years from delivery of this product, Panasonic will
engaged in a personal and non-commercial activity and/or was give to any third party who contacts us at the contact information
obtained from a video provider licensed to provide AVC/VC-1 provided below, for a charge no more than our cost of physically
Video. No license is granted or shall be implied for any other use. performing source code distribution, a complete machine-readable
Additional information may be obtained from MPEG LA, LLC. copy of the corresponding source code covered under GPL V2.0,
See http://www.mpegla.com. LGPL V2.1 or the other licenses with the obligation to do so, as
well as the respective copyright notice thereof.
MPEG Layer-3 audio coding technology licensed from Fraunhofer Contact Information: oss-cd-request@gg.jp.panasonic.com
IIS and Thomson. The source code and the copyright notice are also available for
free in our website below.
“DVD Logo” is a trademark of DVD Format/Logo Licensing http://panasonic.net/avc/oss/theater/AWTHT14A.html
Corporation.
(1) MS/WMA
“Wi-Fi”, “Wi-Fi Protected Setup”, “WPA” and “WPA2” are marks or
This product is protected by certain intellectual property rights of
registered marks of the Wi-Fi Alliance.
Microsoft Corporation and third parties. Use or distribution of such
The Bluetooth® word mark and logos are owned by the Bluetooth technology outside of this product is prohibited without a license from
SIG, Inc. and any use of such marks by Panasonic Corporation is Microsoft or an authorized Microsoft subsidiary and third parties.
under license. (2) MS/PlayReady/Final Product Labeling
Other trademarks and trade names are those of their respective This product contains technology subject to certain intellectual
owners. property rights of Microsoft. Use or distribution of this technology
outside of this product is prohibited without the appropriate
Android is a trademark of Google Inc. license(s) from Microsoft.
(3) MS/PlayReady/End User Notices
Content owners use Microsoft PlayReady™ content access
technology to protect their intellectual property, including copyrighted
content. This device uses PlayReady technology to access
PlayReady-protected content and/or WMDRM-protected content. If
the device fails to properly enforce restrictions on content usage,
content owners may require Microsoft to revoke the device’s ability to
consume PlayReady-protected content. Revocation should not affect
unprotected content or content protected by other content access
technologies. Content owners may require you to upgrade PlayReady
to access their content. If you decline an upgrade, you will not be able
to access content that requires the upgrade.
(4) Vorbis, FLAC, WPA Supplicant
The software licenses are displayed when “License” in the Setup
menu is selected. (> 32)
Reference
(Inside of product)
VQT5F60
45
11
Getting started
2 Select title numbers, etc./Enter numbers
3 Cancel
15 4 Select Bluetooth®/Enable pairing (> 21)
リワヱヶヵ 5 Select an audio or video source
1 モヷ 6 Basic playback control buttons (> 18)
7 Select preset radio stations (> 23)
8 Show the status messages (> 19)
2 9 Show Pop-up Menu/Top Menu (> 19)
16 10 [, , , ] : Move the highlight for selection
[OK] : Confirm the selection
3 17 () : Frame-by-frame (> 18)
4 モヶュリヰ
18 11 Show Option menu (> 25)
5 ヴユロユヤヵヰン リワヵユンワユヵ 19 12 Colored buttons (red, green, yellow, blue)
Used for various purposes depending on the
6 ヴユモンヤラ
ヱロモヺ ヴユモンヤラ
20 display
ヴレリヱ ヴロヰヸ ヴレリヱ
13 Set the sound effects (> 26)
7
ヱモヶヴユ
14 Set the sleep timer
ヴヵヰヱ ユヹリヵ
Press [SLEEP].
8 21 While “SL ``” is displayed on the unit’s
display, press [SLEEP] several times to
ヶ 22 select the time (in minutes).
ワヶ
ヮユ
ユワ
ラヰ
ヱチ ヮ
ヵヰヱチ
VQT5F60
9
12
10
1 2 3 4 5 6 7 8 9
1 Disc tray 6 Stop
2 Display 7 Start play
Unit’s display list 8 USB port
3 Remote control signal sensor 9 Standby/on switch (¦/I)
Distance: Within approx. 7 m (23 feet). Press to switch the unit from on to standby
Angle: Approx. 20G up and down, 30G left and right mode or vice versa. In standby mode, the unit
4 Open or close the disc tray is still consuming a small amount of power.
5 Adjust the volume of the main unit 10 NFC touch area
1 2 3 4 5 6 7 8
10 VQT5F60
13
6.2. Connection to a TV
14
Tray
15
16
17 17
8.2.3.
8.2.3. Privately
8.2.3. Privately Mode
Mode2 22
PrivatelyMode (Remote
(Remote Cont.
Cont.
(Remote Buttons:
Buttons:
Cont. [5] [5]
Buttons: [9] [9]
[5] [9] [Red])
[Red]).
[Red])
18
18
18
19
20
21
22
(*b)
≥ If downloading on this unit fails or this unit is not
1.Power on. connected to the Internet, then you can download the
2. Press [5][9] and [red] on remote controllatest firmware from the following website and burn it
to a CD-R to update the firmware.
simultaneously for more than 5 sec. http://panasonic.jp/support/global/cs/
3.[70RET] appears on LED display. (This site is in English only.)
To show the firmware version on this unit. (> 32,
4.Press [ ] on remote control . “Firmware Version Information”)
≥ Downloading will require several minutes. It may take
5.[80RET] appears on LED display. longer or may not work properly depending on the
6.Press [OK] on remote control connection environment.
≥ If you do not want to check for the latest firmware version,
7 Wait for about 30 sec
7.Wait for about 30 sec. set “Automatic Update Check” to “Off”. (> 32)
14 VQT5F60
8.[SERV]] appears on LED display.
9.Press [9][9] on remote control .
10.Error code be delelted .
11.Press and hold [Power] on (remote control
About Circuit
or unit) and exit the service mode.
END
(*a)
Refer to P7 3.3 No Symptom
How to Update Firmware
(*b) 23
1.Power on.
2. Press [5][9] and [red] on remote control
simultaneously for more than 5 sec.
Downloaded 3.[70RET] appears on LED
from www.Manualslib.com display.
manuals search engine
Symptom -1 Symptom -2
Symptom -1 VOLTAGE DATA(measurement value)
No power Disc Tray Can not OPEN or CLOSE
. REF.NO. PIN NO. XP10
1 -
*1 2 GND
Check AC inlet unit. Exchange the Check the
(cutting or damage…etc.) AC inlet unit 3 GND
NG OPEN/CLOSE SW. Exchange the
7 feeling ...etc.)
(Break or click 1 4NG GND
Front P.C.B.
OK 5 25.6V
6 25.6V
Check the AC cord. Exchange the OK 7 25.6V
(cutting or damage…etc.) NG AC cord
OK
REF.NO.
Check the Front Panel PIN NO. XP9
(Broken ...etc.) Exchange Front Panel
Check the
Power supply P.C.B. is Exchange the 1NG 3.3V
Fuse-resistor(F501) broken? Power supply P.C.B.
NG 2 3.3V
OK 3 1.7V
OK
4 PIO9
Check the 5 PIO11
Exchange the
Digital P.C.B. connector
NG Power supply P.C.B. 6 PIO13
voltage *1
voltage.*1 Check the Digital P.C.B.
PCB Exchange the
connector XP4 voltage.*3 Digital P.C.B.
7NG GND
OK
8 3.3V
24
24
OK
he
Exchange the
connector
NG Power supply P.C.B.
*1 Check the Digital P.C.B.
PCB Exchange the
connector XP4 voltage.*3 Digital P.C.B.
NG
e
B. connector Exchange the
*2 NG Digital P.C.B. OK
*3*3
25
REF.NO.
Remote Control does notPIN NO.
work XP9
No LED Display/Keys does not work
1 3.3V
2 3.3V
3 1.7V
4 PIO9
Check the battery of Exchange the
Check the Digital P.C.B. Exchange the the Remote Control 5 PIO11
battery
connector XP9 voltage.*2 NG
Digital P.C.B.
NG 6 PIO13
7 GND
8 3.3V
OK
OK
9 GND
10 3.3V
Exchange the Front P.C.B. *2
11 0V
Check the Digital P.C.B. Exchange the
connector XP9 voltage.*212 0V P.C.B.
Digital
NG
13 3.3V
14 3.3V
CHECK POINT LOCATION 15 3.3V
*2 OK 16 3.3V
17 3.3V
18 11.9V
Exchange the 19 GND
Front P.C.B.
20 BT_L
21 GND
22 BT_R
23 GND
24 NFC_FD
24
26
OK 8 3.3V
9 GND
10 3.3V
*2
11 0V
Check the Digital P.C.B. Exchange the
connector XP9 voltage.*2 Digital P.C.B. 12 0V
NG
13 3.3V
14 3.3V
15 3.3V
OK
16 3.3V
17 3.3V
24
27
No Picture No Sound
Check the Input Source Choose Correct Source Check the Connection reconnect correctly
NG NG
OK
OK
Check the Setup Check the Speaker Box Exchange the Speaker Box
Setup Deepclolor and
of HOME menu Progressive off ((*c)
c) NG
NG
OK
OK
*(c)
28
Reset Bluetooth
Check the NFC P.C.B NG from Setup Menu Setup Correct
Exchange the OK
Front PCB Connetor *4
Voltage waveform( *d ) NFC P.C.B.
NG
OK
NG
Check the FFC Exchange the FFC
NG
Check the FFC Exchange the FFC OK
OK NG
Check the Front P.C.B Exchange the
Front P.C.B
Check the NG Exchange the
Front P.C.B Front P.C.B OK
Exchange the
Digital P.C.B.
*4
(*d)
29
Change to other OK
discs and try Disc error
playback again
NG
OK
Exchange the
Digital P.C.B.
Symptom -10
Fan does not work
NG
NG
Exchange the
Digital P.C.B.
30
PVDD(25.5V)
PPLY
POWER SUPPLY
P11
XP11
PVDD(25.5V)
PVDD(25.5V)
P.C.B.
XP7
XP1
Source Switch1 Power Stage Power Stage Power Stage GND
Crystal
74LVC1G3157 TI5342A TI5342A TI5342A GND
27M
GND 4
P
PCON
1
1 1
Audio Processor
1 TAS5538DGG 1 USB_VCCF
4
XS1
TPIC_COMMON USBP1
XP6
TPIC_U USBM1
MPEG DECODER
*6
KEY*6
TPIC_V GND 5
MT8561 4 1
TPIC_W MOTOR
XP5
DRIVER
MGND DDR3 BT_AUDIO_EN
1
TPIC2060 1
TPIC_B+ 1 1GbX1 BT_STATUS
A
TPIC_B- BT_RESET
_
TPIC_A+
2GbX1 PIO9
ER
LED DRIVER
ay
LED Display
MECHANISM TPIC_A-
Crystal
C t l PIO11
UNIT 12M
PIO13
9 GND
BT_3V3
GND
CE FLASH
ADC 3.3V_STBY_MCU
C 2Gb V CLK
V_CLK
1
XP1
9
XP9
V_DATA
IR
MCU V_STB
STM08S005C6 IR_IN 6
1 POWER
TPIC_LOAD- PLAY/PAUSE
XP4
USB
TPIC_LOAD+ OPEN/CLOSE
MGND Source Switch2 +12V_D
2
TPIC_TRAYIN#
74HC4052 GND
BT_L
4
GND
BTM8630
ROM BT
BT_R
BTM8
GND
TUNER FM AUX 24
NFC_FD 2
3 7
1 XP29 2 1 XP3 2
NFC P.C.B.
6
1
4
31
32
Mechanism Unit
Digital P.C.B.
Front P.C.B.
Power Supply P.C.B.
NFC P.C.B.
33
(2)
Front Panel
36
34
Screw (A)
Body Chassis
Screw (A)
Hooking part
Connector (A)
Screw (A)
37
35
FFC(B)
Connector(A)
FFC(A)
Screw (C) Digital P.C.B.
Screw (C)
12.3.9. AC Inle
1. Cut the cable tie
2. Detach the lead
FFC(B) 3. Remove the Ferr
4. Unlock the 2 tab
38
38
36
AC Inlet Unit
Screw (A)
Mechanism Unit
Tab (A)
38 37
13.1. When Replacing the Mechanism Unit and/or Digital P.C.B. Unit
When replacing the mechanism unit, Digital P.C.B. Unit or both, the drive adjustment is required. The adjustment is performs
reading QR coded adjustment value by web camera and writing the value to Digital P.C.B. Unit.
1 - PC 1 -
Web camera • Web camera of 300,000 pixels or more
(For reading the QR code label pasted to the that closeup photography is possible up to
back of the mechanism unit) several centimeters (It is enough usually by
300,000 pixels).
Recommended Web camera: The focus function recommends manual.
Logitech Webcam C200 • It recognizes it automatically only by the
(The same camera as using to read QR code connection to PC.
of Mountbox unit for DSLM(Digital Single Lens Web Camera for USB video class (UVC) that
Mirrorless) doesn’t need special device driver.
A lot of marketed commodities correspond to
2 - 1
the USB video class.
13.1.1.3.Preparation
Before starting the adjustment, install the software for adjustment (QR code reading software for Web camera and the
software for the code writing to Digital P.C.B.).
Note:
The adjustment software can be downloaded from “Support Information from NWBG/VDBG-AVC” web-site in“TSN
system”,together with instructions of “Adjustment Software” including preparations and connections etc.
38
41
39
42
40
1. Connect the Main Unit to TV, then turn the Main Unit on.
2. After start up, make the Main Unit go to the Setting UI
using Remote Control.
41 43
44
42
When replacing the Front P.C.B. Unit, NFC P.C.B. Unit or both, the MAC address of bluetooth module on Front P.C.B. Unit
13.2. When
registration Replacing
to NFC tag on NFC P.C.B. the FronttheP.C.B.
Unit. Perform following Unit and/or
procedures NFC P.C.B. Unit
to register.
(In thisreplacing
When manual, the
the Front
screenshots are using
P.C.B. Unit, NFC of Android
P.C.B. Unit4.4.2..The display
or both, the may varyofdepending
MAC address on the version
bluetooth module of P.C.B.
on Front Android.)
Unit
registration to NFC tag on NFC P.C.B. Unit. Perform the following procedures to register.
13.2.1.
(In this manual, List of Service
the screenshots areTools
using of Android 4.4.2.. The display may vary depending on the version of Android.)
13.2.1.1. Commercial
13.2.1.2.
13.3.1.2. Setting Tools Required
Software
Tag writer Installation
Software Installation 3. Confirming message is displayed, tap [OK].
Preparation: Checkmark is added to [Unknown sources.]
Before starting
No. thePart
adjustment,
No. download theUsesNFC tag Pcs. Compatibility
Preparation:
writing software
1 (NFCWriter_apk_V1.3_20140226.apk)
- NFC compatible Android device 1 Android 4.1 or higher
from
Download
“SupportNFC tag writer
Information software (TCL BT TAG
from NWBG/VDBG-AVC” 3. When below confirming information appears, tap [OK].
13.2.1.2. Setting
in “TSNSoftware
writerV1.4.apk)
web-site from “Support
system”, andInstallation
Information
send from NWBG/
the downloaded APK 3. Confirming
Make suremessage is displayed,
the [Unknown sources]tap [OK].checked.
being
Preparation:VDBG-AVC” web-site in
file to NFC compatible Android device. “TSN system”, then send it to Checkmark is added to [Unknown sources.]
Before starting
NFC
There is athe adjustment,
compatible
method such asdownload
Android device.
send the NFC
as You
emailcan tag it as an
send
attachments.
writingattachment
software (NFCWriter_apk_V1.3_20140226.apk)
by email or other methods.
from1.1.
“Support
Open
Openthe Information
the [Settings]from
[Settings] screen
screen NWBG/VDBG-AVC”
ofAndroid
of the Android
device,device, then
then tap
web-site tapin[Security]
“TSN to
system”,open andthe [Security]
send
[Security] to open the [Security] screen.the screen.
downloaded APK
2. NFC
file to Check the of [Unknown
compatible Android device.sources].
2. Tap the of [Unknown sources].
There is a method such as send as email attachments.
43
4. Tap APK file of NFC tag writing software which received 6. Open
7. Open the
the [Settings]
[setting] screen
screen ofagain.
Android
Tapdevice again,tothen
[Security] open
to install. tap [security]
the [Security] screen.
to open the [Security] screen.
8.
7. Tap
Tap the
the ofof[Unknown
[Unknownsources]
sources]to
tocancel thecheckmark.
clear the checkmark.
44
5. Tap5.[Write
Tap to Tag],tothen move the NFCthepartNFC
of thepart
Android
5. 5.
TapTap[Write
[Write to[Write
Tag].
to Tag], thenTag],
thenmove then
move the move
theNFC
NFCpart
partofofyour of the Android
Android
the Android
device close to NFC antenna part of the NFC P.C.B. Unit.
device device
deviceclose
closetoto close
the
NFC to
NFC NFC antenna
antenna
antenna partpart part
of NFC
of the NFCof the NFC
P.C.B.
P.C.B. P.C.B. Unit.
unit
Unit.
6. Wait till [Tag written successfully!] is displayed, tag writing
and
6. Waithold it until
6.tillWait
[Tagtill a beep
[Tag
written sound
written is heard.which
successfully!]
successfully!] means
is displayed,
is displayed, the
tag writingtag writing
is completed. Tap [Exit] to exit the “TCL BT TAG Writer”
Android isdevice
is completed. is
completed. recognized
Tap [Exit] by the
Tapto[Exit]
exit to NFC
the module.
“TCLthe
exit BT“TCL
TAG Writer”
BT TAG Writer”
software.
6. When [Tag written successfully!] appears, Tap [Exit].
software.
5. software.
Tap [Write to Tag], then move the NFC part of the Android
device close to NFC antenna part of the NFC P.C.B. Unit.
6. Wait till [Tag written successfully!] is displayed, tag writing
is completed. Tap [Exit] to exit the “TCL BT TAG Writer”
3. After selecting the module type, QR code Scan screen is
software.
3. After selecting the module type, QR code Scan screen is
3.displayed. Tap [Skip
After selecting thethe scan.]type,
module to skip
QRthiscode
screen.
Scan screen is
displayed. Tap [Skip the scan.] to skip this screen.
displayed. Tap [Skip the scan.] to skip this screen.
47
45
47
47
Downloaded from www.Manualslib.com manuals search engine
13.3. Caution for Replacing Parts
1 Turn on the power, and confirm items pointed out. Items pointed out should reappear.
If a problem is caused by a BD-Video disc, DVD-R, No abnormality should be seen in the picture, sound or
2
DVD Video, Audio-CD, or MP3, playback the test disc. operation.
After checking and making repairs, upgrade the Make sure that [UPD OK] appears on the LED displays.
3 firmware to the latest version. * [UNSUPPORT] display means the unit is already updated
to newest same version. Then version up is not necessary.
Transfer [9] [9] in the service mode setting, and initialize Make sure that [CLR] appears on the LED display.
the service settings (return various settings and error After checking it, turn the power off.
4
information to their default values. The laser time is not
included in this initialization).
After replacing the Mechanism Unit, transfer [9] [5] in the Make sure that [CLR] appears on the LED display.
5
service mode setting, and initialize the laser used time. After checking it, turn the power off.
Use the following checklist to establish the judgment criteria for the picture and sound.
46
Notes:
*Important safety notice:
Components identified by mark have special characteristics important for safety.
When replacing any of components, be sure to use only manufacture’s specified parts shown in the parts list.
*Parts marked with [PJM] in the remarks column are supplied by PAVCJM,others are supplied by PHK.
Ref. Ref.
Safety Part No. Part Name & Description Pcs Remarks Safety Part No. Part Name & Description Pcs Remarks
No. No.
1 VXY2206 MECHANISM UNIT 1 143 RHD26077 SILVER SCREW (B) 1
47
102
103
101
104
105
16
181 121
161
182 162
15 a
183
193 184
106 185
1 194 13
c 14
196 195
188
197 a
187 18 2
186 190
191
189
19 3
192
17
20
12
7
b
8 141
c
142 10 143 22
9
144 5 21
11
145
4
48
ACCESSORIES BAG
OI BOOK
A2
QSG OI
A3 PREPARATIOPN VER.)
A5 FM INDOOR ANTENNA
P3
PLUG ADAPTOR
A6 (FOR PH ONLY)
SC-BTT405
BATTERIES (NOT SUPPLIED)
A7 SPEAKER STICKERS
A1 Remote Control
A4 AC CORD
(FOR P ONLY) P4 Mirror Bag
A4 AC CORD
P2
(FOR PH ONLY)
Speaker Connection
Cables
SB-HFS4010
SB-HC4010
SB-HFS4010
P1
49