Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
ONEMESH500
• ‘one’ rolled into every sheet:
Your OneSteel guarantee of quality
• Square (S), Rectangular (R) & Trench Mesh (TM}
• Yield Strength: Min. characteristic value 500 MPa
• Uniform Elongation (Agt):
Mininum characteristic value 1.5%
• Ratio of Tensile to Yield Strength:
Minimum characteristic value 1.03
• Complies with AS4671 Reinforcing Materials,
AS2870 Residential Slabs and Footings &
AS3600 Concrete Structures
ONEMESH500 is a multi-
ONEMESH500 purpose steel reinforcing
multi-purpose mesh suitable for use in
general concrete pavement
mesh applications, residential raft
slabs and footings to AS2780
and most structural
applications to AS3600 and
AS2327.1.
Its minimum Yield Strength
of 500MPa is the same as
500PLUS Rebar, simplifying
designs that historically had
a mixture of 400, 450 and
500 MPa reinforcing steels.
The Uniform Elongation (Agt)
of 1.5% reflects the Low
Ductility Class L classification
in AS4671.
It also satisfies the current
requirements of AS2870,
Amendment 2 1999 &
Amendment 3 2002, which
call for a minimum Agt
value of 1.5% in all 500
grade meshes used in
residential slabs in Australia.
3
mesh solutions m e s h s o l u t i o n s
ONEMESH500
Class L mesh to AS4671 is designated
by wire shape, wire yield (proof) strength, mesh
configuration, wire size & wire spacing (pitch).
For example, D500SL92 is a Square (S), Class L (L)
mesh (500 MPa) with deformed (D) wire, with a
nominal diameter of 9 mm (actual 8.6 mm), spaced
at a pitch of 200 mm.
ONEMESH500
specifications
Approx mass of Cross-sectional
Mesh Specification
Wire Diameters 2.4m x 6m sheets area
Longitudinal Wires Cross Wires
These are specified on the Product Longitudinal Cross
Wires Wires
basis of being able to Code No X Size @ Pitch No X Size @ Pitch Area Sheet
mm2/m
mm mm mm mm kg/m2 kg mm2/m
demonstrate Agt compliance
with a minimum specified Rectangular Meshes (RL)
cross-sectional area. RL1218 25 X 11.90 @ 100 30 X 7.60 @ 200 10.5 157 1112 227
Lapping of Fabric Sheets RL1118* 25 X 10.70 @ 100 30 X 7.60 @ 200 8.8 130 899 227
RL1018 25 X 9.50 @ 100 30 X 7.60 @ 200 7.3 109 709 227
Lap splicing of welded fabric RL918* 25 X 8.60 @ 100 30 X 7.60 @ 200 6.3 93 581 227
is covered by Section 13.2.4 RL818 25 X 7.60 @ 100 30 X 7.60 @ 200 5.3 79 454 227
of AS3600. RL718* 25 X 6.75 @ 100 30 X 7.60 @ 200 4.6 67 358 227
It states that a lapped splice Square Meshes (SL) with edge lapping wires
for welded wire fabric in SL102 10 X 9.50 @ 200 30 X 9.50 @ 200 5.6 80 354 354
tension shall be made so that +4 X 6.75 @ 100
the two outermost transverse SL92 10 X 8.60 @ 200 30 X 8.60 @ 200 4.6 66 290 290
wires of one sheet of fabric +4 X 6.00 @ 100
SL82 10 X 7.60 @ 200 30 X 7.60 @ 200 3.6 52 227 227
overlap the two outermost
+4 X 5.37 @ 100
transverse wires of the sheet SL72 10 X 6.75 @ 200 30 X 6.75 @ 200 2.8 41 179 179
being lapped. +4 X 4.77 @ 100
SL62 10 X 6.00 @ 200 30 X 6.00 @ 200 2.2 33 141 141
+4 X 4.24 @ 100
Overlap of ends of sheets (with overhang)
SL52* 10 X 4.77 @ 200 30 X 4.77 @ 200 1.4 20 89 89
+4 X 4.00 @ 100
SL63 6 X 6.00 @ 300 30 X 6.00 @ 300 1.5 21 94 94
Overlap of side of sheets WA only +4 X 4.00 @ 100 (2.3m sheet width)
SL53 6 X 4.77 @ 300 20 X 4.77 @ 300 1.0 15 60 60
WA only +4 X 4.00 @ 100 (2.3m sheet width)
* Available on request.
F & RF meshes to AS1304 have been replaced by SL & RL meshes to AS4671 since April 2001
4
mesh solutions m e s h s o l u t i o n s
UTEMESH500
• Versatile
• Lightweight
• Minimises wastage
• Can be handled by one person
• Safe and legal to transport
• Easy to set-up, place and tie
• Full range of accessories
• Ideal for driveways and smaller
concreting jobs
5
mesh solutions m e s h s o l u t i o n s
8
mesh solutions m e s h s o l u t i o n s
engineered mesh
• Minimises waste
• Faster floor cycles
• Reduces on-site labour
• Simplifies placement of reo
• Improves speed of construction
• Closely matches engineering intent
• Prefabrication work completed under factory
conditions