Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
This is (o certify `hat the equipment identifled below has been tesled in accordance with the relevant type
approval procedures of the Marine Equipment Directive and was found in compliance with the requiremenls of
the international standards contained therein.
Conformity Assessment a
Procedure
Documents • Test reporfe ace. to MEPC 60 (33), Part 2, 3 and 4 conducted ln May 2000
I DRC.No.: 106089-General Arrangement, DRG.No.: 107080-Main PCB,
DRC.N®.: 107087CM M®nitor Di€play
I Operation Manual, Test and Calibrauon Procedures
None
20100606
GL Luxembourg
EC Identification No.: 0801
Page 10„
Luxembourg, 2005-05-30
(._-.-.
14. SPARES
OTHER SPARES
This is to certify that the oil content meter comprising the equipment listed has been
examined and tested in accordance with the requirements of IMO Resolution MEPC.60(33) . This
certif icate is valid only for the oil content meter referred to in this certificate. Oil
content meter analyzing unit manufactured by RTE to dwg. no. 106780 dtd. 05 May 2000.
The oil content meter is acceptable for use with a 15 ppm bilge alarm in accordance with
regulation 16(5) of Annex I to MARPOL 73/78.
A copy of this certif icate should be carried aboard a vessel f itted with this equipment at
all times. IMO Certificates of Type Approval do not expire and are valid for equipment
manufactured at any time during the period of validity of this certificate. Test data and
roculcc attached ag appondir
This certificate renews approval nuhoer 162.050/3022/0 dated 4 August 2000 and documents
compliance with MEPC.60(33) .
-++ END +.+
I llls IS 10 (.I.Rl lF\ Tll;\ I lhc .ilwn`` ii.iim`d in.iiiiil.u l`irt.r lms siiliinillcil lti lli.` iimlcrsigiit``I s.ilisl.iclim' cvidcii.e lli.W Ilit` ilcm specllic.I licrclii ciiiiiitllcs
w illi "w ,iitiilic.ilili` l`iws .iii{I icgiil.iliiins .is ti`Illmcil tiii ihc lcvcrsc sl{lc lil lhi` (`cllili.,Ill. .iiiil .iii|"`w." i` hclc.lu gi`'i`ii I hls .iprtltn.il sh.Ill l`i` in cllccl `mol lllc
i.\iili.Ititln il.Itt` l`crctili `inlc„ `titiiici I.intclctl I)I `LisrcliLlt``l h.\ riitiiicf ,ititht» il}'
8. G. BUBAR
Chief. Engineering Division
U.S. Coast Guard Marine Safety Center
EQUIPMENT SERIAL No.: i S S.¢'f;t:G` i 15 MAIN PCB SERIAL No.: I G 7 €1€, i; €;=> Ct -J\
DISPLAY PCBSERIAL No.: L£|C}`il£#€`;lf; CELL ASSEMBLy SER,AL No.: b§ €\{~=jrfR 7C ,i i =2#*b
-I LftT:-;i,-# - [i,.£
SOFTWARE VERSION: MAX ALARM SETPOINT i: =¥-ff"ife
¥,
Options fitted.
TEM Initia,s
-:JTf-ifiti
Final shipping and packing inspection carried out in accordance with
Rivertrace Engineering procedure 107084 Rev F
SIGNED: