Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
0
Database version
2019.12.13.14.48
Date
04/03/2020
fischer FZE
Enquiry@fischer.ae
www.fischer.ae
Design Specifications
Anchor
Anchor system fischer Bolt anchor FBZ
Anchor Bolt anchor FBZ 10/10, zinc plated steel
Calculated anchorage 60 mm
depth
Design Data Anchor design in Concrete according European Technical
Assessment ETA-17/0624, Option 1,
Issued 08/09/2017
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 1
C-FIX 1.85.0.0
Database version
2019.12.13.14.48
Date
04/03/2020
Input data
Design actions *⁾
# NSd VSd,x VSd,y MSd,x MSd,y MT,Sd Type of loading
kN kN kN kNm kNm kNm
1 -1.00 0.08 0.80 0.25 0.00 0.02 Static or quasi-static
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 2
C-FIX 1.85.0.0
Database version
2019.12.13.14.48
Date
04/03/2020
Steel failure
( NRd,s )
βN,s
Anchor no. % Group N° Decisive Beta
1 1.2 1 βN,s;1
2 0.0 2 βN,s;2
Pullout failure
( NRd,p )
βN,p
Anchor no. % Group N° Decisive Beta
1 3.4 1 βN,p;1
( NRd,c )
Eq. (5.2)
Eq. (5.2a)
Eq. (5.2c)
Eq. (5.2d)
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 3
C-FIX 1.85.0.0
Database version
2019.12.13.14.48
Date
04/03/2020
Eq. (5.2e)
βN,c
Anchor no. % Group N° Decisive Beta
1 2.0 1 βN,c;1
( VRd,s )
βVs
Anchor no. % Group N° Decisive Beta
1 2.3 1 βVs;1
2 2.4 2 βVs;2
( VRd,cp )
Eq. (5.6)
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 4
C-FIX 1.85.0.0
Database version
2019.12.13.14.48
Date
04/03/2020
Eq. (5.2)
Eq. (5.2a)
Eq. (5.2c)
Eq. (5.2d)
Eq. (5.2e)
βV,cp
Anchor no. % Group N° Decisive Beta
1 1.1 1 βV,cp;1
2 1.2 2 βV,cp;2
( VRd,c )
Eq. (5.7)
Eq. (5.7a)
Eq. (5.7b/c)
Eq. (5.7e)
Eq. (5.7f)
Eq. (5.7g)
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 5
C-FIX 1.85.0.0
Database version
2019.12.13.14.48
Date
04/03/2020
Eq. (5.7h)
βV,c
Anchor no. % Group N° Decisive Beta
1 1.8 1 βV,c;1
2 2.1 2 βV,c;2
Eq. (5.9)
Technical remarks
All data and information in the software is based on fischer products and common engineering knowledge. Please
check all the proof results against local valid standards and approvals.
As fischer is not the design office, the attached is no guarantee for incorrect input or assumptions. Any
recommendations have to be approved by the building-authority or project engineer. Results are valid only for
anchor system calculated in the attached. If any part of the system is changed, it will invalidate this report and new
calculations would be required. The calculation was done under the assumption that a sufficient
splitting reinforcement is available. In this case the spliiting
failure can be omitted.
The transmission of the anchor loads to the supports of the concrete member shall be shown for the ultimate limit state and
the serviceability limit state; for this purpose, the normal verifications shall be carried out under due consideration of the
actions introduced by the anchors. For these verifications the additional provisions given in the current design method shall
be taken into account.
As a pre-condition the anchor plate is assumed to be flat when subjected to the actions. Therefore, the plate must be
sufficiently stiff. The C-Fix anchor plate design is based on a proof of stresses and does not allow a statement about
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 6
C-FIX 1.85.0.0
Database version
2019.12.13.14.48
Date
04/03/2020
the stiffness of the plate. The proof of the necessary stiffness is not carried out by C-Fix.
During the design process, the following hints and warnings were issued:
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 7
C-FIX 1.85.0.0
Database version
2019.12.13.14.48
Date
04/03/2020
Installation data
Anchor
Anchor system fischer Bolt anchor FBZ
Anchor Bolt anchor FBZ 10/10, zinc plated Art.-No. 543401
steel
Installation details
Thread diameter M 10
Drill hole diameter d0 = 10 mm
Drill hole depth h2 = 85 mm
Calculated anchorage hef = 60 mm
depth
Installation depth hnom = 72 mm
Drilling method hammer drilling
Drill hole cleaning only blow out by hand
Installation type Push-through installation
Annular gap Annular gap not filled
Installation torque Tinst = 45.0 Nm
Socket size 17 mm
Base plate thickness t = 3 mm
Grout thickness g ≤ 5 mm
Total fixing thickness tfix ≤ 8 mm
Tfix,max tfix, max = 10 mm
Attachment
Profile type Customized profile
Distance between profiles 30 mm
Profile dimensions mm
Height 5
Anchor coordinates
x y
Anchor no. mm mm
1 0 175
2 0 -175
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 8