Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
I C M icro, TDA8370
TVS-2158PFS (H)
TVS-2108M SC
TVS-2155PFS (H)
TVS-2142M A (H)
TVS-1463M A
Electric
circuit AV: SCART
FE-CVBS
VIF
SAW
IF-filter
P3.0/ADC0 3 = SVHS-Y
Vol/Mute
AUDIO
C 4 3
4 = SVHS-C
CVBS/Y
AGCOUT
P3.2/ADC CVBS
INT0
External
NICAM module board
RC5N Keyb/LED
RC5 Analogue
TDA9874 receiver keyboard WOOFER
and LED Electronic WOOFER
Circuit
AUX
L
AMP L
TDA9801
FE TDA9859 R
2. Adjustment technology:
1. Safety caution:
1.1.X-ray radiation:
1.1.1. Ultra high voltage will cause harmful x-ray, the high voltage should be adjusted
within the specified limit to avoid radiation injury. This TV can operate under
220V/50Hz normal city power supply. The high voltage should be under 26.5kv
with the conditions of zero beam current (lowest brightness) and 110v main
power supply. The high voltage must not over 31kv in no case.
Check the high voltage before maintenance with reference of the high voltage
check as specified in this section with reliable and accurate high voltage meter.
The main power supply should keep around 110V.
1.1.2.X-ray radiation is mainly generated from the tube, the tube of the TV has passed the
safety verification, so tube should be replaced with the same or similar type passed the safety
verification and check the high voltage as indicated.
+B power supply voltage adjust ---AGC adjust ----aging under normal temperature
----focus adjust-----white balance adjust------picture adjust
3. General description:
3.1. The EEPROM in the chassis has been copied in terms of the data of standard
sample TV, factory adjustment may needed if necessary. If the blank EEPROM
is used, the IIC data must be loaded before other normal adjustment.
3.2. The following conditions are applied to the whole TV adjustment if no specific
requirements:
a. AC power supply 220V/50 Hz.
b. 30 min. pre-warming or above.
3.3. Automatic built-in de-gauss circuit, auto de-gauss will be completed around 1
second after switching on the main power supply. The de-gauss circuit will be
effective 30min. after switching off.
If the tube causes interference with the color purity and convergence and
built-in de-gauss circuit is not fully effective, the de-gauss device can be used to
cancel magnetism externally.
FIELD IC 9302B
VOLTAGE RESISTANCE PIN VOLTAGE RESISTANCE
,+B: 110V 4.8K 1 0.67V 1.5K
2 13.39V 5.6K
FIELD POWER
13.3V 5.3K 3 ,-11.85V 500K
SUPPLY:
4 ,-13.32V 550K
SOUND POWER
11.3V 0.8K 5 AC 4.94V 153Ω
SUPPLY:
DECODE POWER
11.1V 5K 6 13.70V 13K
SUPPLY:
VIDEO
AMPLIFIER
195V 7 0.68V 1.6K
POWER
SUPPLY:
1) SERVICE page 0
ITEM NAME DESCRIPTION
0 FREQUENCY 50HZ/60HZ
1 H PH Line center. Default:32 (0~63)
2 V SL Field linearity. Default:32(0~63)
3 V SH Field center. Default:32 (0~63)
4 V SI Field amplitude. Default:32 (0~63)
5 V SC Field SC correct. Default:32 (0~63)
6 EW WIDTH EW WIDTH
7 EW PARA EW PARA adjust
8 UP CORNER UP CORNER adjust
Only OM8373series
9 LO CORNER LO CORNER adjust
10 H-PARA Parallelogram adjust
support
11 H-BOW Bow adjust
12 EW TRAPE Trapezoid adjust
2) SERVICE Page 1
ITEM NAME DESCRIPTION
0 AGC RF.AGC Adjust.D efault:24 (0~63)
1 AGC SPEED AGC SPEED . Default:1 (0-3)
2 CORING CORING . Default:0 (0-3)
3 FREQ LH FREQ LH(Annotate 3)
4 FREQ HU FREQ HU(Annotate 3)
5 BAND 0:TABLE 1 ; 1:TABLE 2 (Annotate 3)
6 YUV- BR YUV RED
7 YUV -BG YUV GREEN
8 WIDE WIDE MODE Field amplitude Adjust
9 ZOOM ZOOM MODE amplitude Adjust
3)SERVICE PAGE 2
ITEM NAME DESCRIPTION
0 UOC VOL SW UOC volume SWITCH。Default:OFF
1 UOC/PWM VOL UOC/PWM immobility VOLUME。Default:63
2 VOL 10 10%. Default:25(0~100)
3 VOL 25 25%. Default:50(0~100)
4 VOL 50 50%. Default:75(0~100)
5 VOL100 100%. Default:100(0~100)
6 FMWS FMWS . Default:0(0~2)
7 AVL OPT OFF:AVL OFF;ON:AVL ON。Default:ON
8 AGN FM OUTPUT PLUS CONTROL:
OFF:NORMAL ON:+6dB
4)SERVICE PAGE 3
ITEM NAME DESCRIPTION
0 AV OPT OFF: formerly logic ON: new logic。Default:OFF
1 AV CFG AV choose (0~7) 。Default:3
2 VIDEO OUT AV out:TV signal same with screen。Default:CVBS
3 PIN 5 Pin function setting. Default:NTSC(Annotate 2)
4 PIN 7 Pin function setting. Default:VOL1(Annotate 2)
5 PIN 8 Pin function setting. Default:MUTE(Annotate 2)
6 YC/DVD DVD switch。
Annotate 1: AV select:MENU3ÆAV CFG:
0=TV→AV; 1= TV→AV1→AV2; 2= TV→AV1→AV2→SVHS;
3= TV→AV1→AV2→SVHS→YUV; 4= TV→AV1→AV2→YUV;
5= TV→AV→SVHS; 6= TV→AV→SVHS→YUV; 7= TV→AV→YUV;
Annotate 2:PIN 5 PIN7 PIN8 HAVE OTHER FUNCTIONS SETTING AS FOLLOWS::
VOL1 PWM LEFT TRACK
VOL2 PWM RIGHT TRACK
NTSC SWITCH M/N. M/N:L ELSE:H
DVD L:OFF H:YUV
MUTE MUTE:H
5060 50HZ:H 60HZ:L
MUTE1 CONTROL whisht. MUTE:L
MUTE2 CONTROL whisht. MUTE:H
SV-DT S-VIDEO
Annotate 3: Parameter Setting of Synthesized Frequency Tuner:
The dividing frequency of VHF and VHFH,adjust range:100.75MHz~227.25MHz(spacing
0.5MHz)
The dividing frequency of VHFH and UHF,adjust range :300.25MHz~555.25MHz(spacing
0.5MHz)
BAND OPT:
WHEN BAND=0:
Band BS3 BS2 BS1 BS0
VL 0 0 0 1
VH 0 0 1 0
UHF 0 1 0 0
WHEN BAND =1:
Band BS4 BS3 BS2 BS1
VL 0 × 0 1
VH 0 × 1 ×
UHF 1 × × ×
5) SERVICE PAGE 4
ITEM NAME DESCRIPTION
0 VP OSD field location. Default:52 (0~63)
1 HP OSD line location. Default:38 (0~60)
2 MENU TITLE Change the color of menu BAR. Default:61(0~63)
3 YUV HS RGB/YUV Line center. Default:52 (0~63)
4 YUV OSD HS RGB/YUV OSD Line center. Default:38 (0~60)
5 OSD L OSD output contrast。Default:0 (0~3)
6 SC.BRI Line brightness。Default:8 (0~63)
6) SERVICE PAGE 5
ITEM NAME DESCRIPTION
1 BTSC-MODE MONO
2 BTSC-ST Restrict stereo yawp. Default:7 (0~15)
3 BTSC-SP Restrict SAP yawp. Default:7 (0~15)
4 BTSC-LI Default:12 (0~31)
5 BTSC-A1 Apart degree. Default:22(0~31)
6 BTSC-A2 Apart degree. Default:12(0~31)
7 BTSC-TC Time constant . Default:4(0~7)
8 BTSC-STS Stereo incision. Default:OFF
9 BTSC-ADJ Default:START (START/BUSY)
7) SERVICE PAGE 6
ITEM NAME DESCRIPTION
0 POW Power-on mode selection. Default:1(0:standby 1:power-on 2:
memory power-on)
1 LOGO Logo selection . Default:OFF
2 SAVER Screen protecting mode selection. Default:OFF
3 POWER ON TIM Power-on delay. Default:8(6-15)
4 AKB Default:ON
5 NBL Default:ON
6 IF Picture intermediate frequency selection
7 PWL
8) SERVICE PAGE 7
ITEM NAME DESCRIPTION
0 SUB CON Sub-contrast. Default:15(0~63)
1 SUB BRI Sub-brightness. Default:18(0~63)
2 SUB COL Sub-color.Default:30(0~63)
3 SUB SHA Sub-acutance. Default:32(0~63)
4 SUB TI Sub-hue. Default:16(0~31)
5、General troubleshooting:|
lack of the blue color
the voltage is
around 3V.
normal
正
test the voltage on the abnormal Are V911、V913、V912、D912
collector of V911 to see if its damaged ?
around 150V.
normal
Test the voltage on pin 7 of the abnormal Bad socket or the tube is
tube to see its around 150V damaged.
normal
Lack of sound
Normal
Are N201、N801、N802
damaged or the loud speaker
is open circuit.
No signal
circuit
Yes
yes
normal
Test the voltage on AGC pin of the abnormal Check to see if the tuner N201 is
5V
normal
Test the voltage of the two abnormal Check to see if the tuner N201 is
switching.
normal
normal
normal
Test the voltage on the emitter of abnormal Check to see if R559 is open
normal
Abnormal
Test to see if the voltage on the emitter Check to see if the pins 3 and 7 of the
of switching transistor V503 is 300V switching power supply transformer is
open circuited.
Abnormal If V502、V501、D511、.R510
Test to see if there is some startup voltage Are damaged
on the emitter of switching transistor V503
Normal
Abnormal
Test to see if the voltage on the collector of power If some of V441、D551、D552、D561、
supply transistor D511 is around 110V V551 be beat through,if N501is damaged
Normal
Abnormal
IF D555、D564 are damaged,
Test to see if the voltage on the collector of power
If R555 is open circuited
supply transistor N701,5 is around 5V
Normal
Abnormal
Abnormal
Test the voltage on pin 1 of Check to see if N301、N201、
N402 to see if its is around N402 are damaged
0.7V
Abnormal
Test the voltage of the field Check the field deflection N301 to see
正
No signal
Abnormal
Check to see if there are noise Check to see if the sound surface filter
flakes on the screen during N201 Z101 is damaged.
program searching.
Abnormal
Test to see if there is 5V input Check to see if D564 is damaged ,tuner
into the tuner power supply pin to the output of
S564 is open circuited.
Abnormal
Test the voltage on pin V7 of the Check to see if the tuner A101、N201
tuner to see if it is varied are damaged.
from 0-32V during program
searching.
Abnormal
Abnormal
Test the voltage on the base, Check to see if V101 、 L101 are
collector, emitter of pre-MF amp. damaged.
Transistor V101 to see if they are
normal
Lack of red
Abnormal
First test the voltage on the base of Check to see if N201、V922、
video amplifier to see if it is VD921 are damaged, or XP902
around 3.7V wiring is open circuited.
Abnormal
Test the voltage on the emitter of
Check to see if V922 is damaged
V922 to see if its around
3.1V
Abnormal
Test the voltage on the collector of Check to see if R927 is restored or
V922 to see if its around 150V the display tube is damaged.
Abnormal
Test to see if the voltage on pin Check to verify if the tube and
2 of the tube socket is around the tube socket are poor
150V quality.
No brightness
Test the voltage on the collector Abnormal Check to see pin 60 of N201 is
of V552 to see if it s around high level, V553、R555、N201
11.5V are damaged , N701 data is
wrong.
正常
Test the voltage on the collector Abnormal Check to see if V401、V551. are
of V401 to see if it is around damaged, R403、D55 and primary
17V coil of T402 are open circuited
Test to see if the voltage across Check to see if the high voltage
Abnormal
the filament of the tube is AC transformer and T401tube are bad,
6.3V and 400 DCV is fed into XS403 wiring is open circuited.
the tube.
TJC3-5P-450MM
R
VCC
OUT1
GND
OUT1
STANDBY
IN1
GND
IN2
VOL
OUT2
GND
OUT2
+5VB 3 3
6、color
D601 C602 4 G 2
IN4148 XS714 XS711
1
2
3
4
5
6
7
8
9
220u
10
11
12
1 2 5 B 1 R928
2 1 RT-1/2W-1.5K
V602 +5V
R608 A1015 R918
2.2K SPEAKER RT-1/2W-1.5K
R610 XS715 XS713 R938
R609 56K RT-1/2W-1.5K
1K 1 2 2W8.2K
2 1
V913
HS003B R913 BF423 D912
R726 R603 BY21
RM901 1K 4.7K R606
3 R604 C605 C623 C611 4.7K C603
10u 10u 10u 1u SPEAKER !
R743 R725 270K V912
2 100 V601 C615
+5VB C616 BF422
R744 7.5MM C1815
1 10 D702 1000 1000
C604 IN4148 V911 R917
N702 X C2482
R911 220
C743 X
1 8
R729
3.3K
R708
3.3K
10u
R709
3.3K
A0 VCC R916A
R346 R347 330
N1 3.3K 3.3K R913
R912 270 R914 C943
C305 C306 10K 47 CT81-2KV-102
0.01 47u
R605 2 7 1 64 D911
A1 WP STAND BY IRIN
470 4148 C911
50V-331
2
3 6 2 63 R613 R611
A2 SCL SCL AV2 2.2k
R728 R614 2.2k R612 R727
AM24C08
3 100 #10K #10K 100
+8V
R606
10K
4 5 3 62 D941
1
GND SDA SDA AV1 N?
+.3V 17 16 HZ9.1
LD901 391
LED 18 15
R715
10K C619 C609
4 61 100V682 19 14 100V682
TUNING VddP
R710 L753 2W8.2K V933
5.6K C755 10uH 20 13 R925 BF423 D401
R702 10u C608 C610 BY21
82K C756 100V153 21 12 100V153
R556 R703 5 60 0.01
+B NTSC SW RESET
R724 68K 22 11 V932
2W12K R616
15K BF422
N550 C559 3.3V C607 1000 23 10 C622 12K
P+ UPC574 50V4.7u R615 100V683 V931 R937
6 59 24 9 C2482
KEY XTAL OUT 8.2K R932 220 C940
R1711 47
1.2K C702 C714 25 8 0.01/500V
P- 220P 103 R936
330
26 7 R933
R1712 7 58 X761 270
R707 R706 R705 VOL1 XTAL IN 12M C618 1000 R936A R934
2.2K 10K 10K 10K R711 C709 27 6 10K
+8V 47
V+ C707 4.7K 471 C762 D931
C706 C705 C761 28 5
0.1 0.1 0.1 33P 33P 4148 C933
R1713 C617 1000 50V-331
2.7K V701 8 57 29 4 C621 C620
C1815 MUTE OSCGND 221
V- R712 W711 10UF
3.3K 10MM 30 3
TV schematic
R1714 C614
10u
180V
HEAT
6.8K 31 2
9 56 R701
1
2 GND
3
4
4 C206
1u Cr
4700
18 47 R820
+8V GND3 G2/YIN 100K
R300A C808
22/1W 1u
R102 R807 R806 R808
2 33K D300A V801 75 75 75
C301 C302 19 46
C817 C1815
0.01 47u 5.1V DECBG R2/VIN 10u
C807 C820
1 C205 1u R823
2.2u 1K 10u
C204
0.1
20 45 V-OUT
C108 AVL/EWD INSSW2
4.7u R208
C211 1K C1815
2.2u V802
21 44
VDRB AUDOUT/AMOUT L-OUT
R401 C818
100 R207 10u
C208 10K
1000 R821 C819
R822 10u
C220 100K 1K
22 43
VDRA CHROMA
R402 R-OUT
100 0.1 R811
LBN2955 C207 R813
Z301 1000 22K 22K
+8v
1u
1 5 23 42 C813 1K
IF1 CVBS/Y R812
C806
1u
4
2 R-IN 2
24 41
IF2 GND1
C814 R814
3
1u 1K
25 40 L-IN 2
IREF CVBSINT
R202
39K +8V
1 16 1 16 C811
26 39 1u V-IN 2
VSC Vp1 C804 R809
C219 2 15 2 15 100
C212 10u 10u
0.1 C221 3 14 3 14
0.01 C222 C812 R810
47u +8V
27 38 V202 4 13 4 13 #100
TUNER AGC IFVO/SVO R216 R221
R226 C1815 R215 100
R203 C209 1.8K 390 R819 5 12 5 12 1u
560 2.2k R222 L202 33K C803
R108 0.01 V841 10u V-IN 1
150K 100 6.8uH C1815 6 11 6 11
28 37
V201
AUDEEM/SIF1 PLL IF R223 R224 C1815
75 7 10 7 10
C210 R206 C217 180 Z201
3300 390 0.1 5.5M R816
R225 8 9 8 9 C815 1K
390 C821 10u R815 L-IN 1
29 36 470u 1K
DECSDEM/SIF2 EHTO R217 R825 N801
C218 100 4052 N802
Z202 10u 100 4052
C213 6.0M
10u
R818
30 35 C816 1K R817
GND2 AUDEXT/QSSO 10u 1K R-IN 1
R453 Z203
2.2K 6.5M
/SI F AGC
31 34
SNDPLL FBISO
TDA93XX
R205 C215
561 R483
2.7K
27K
32 33
C
AVL/REFO H OUT
C214 D482
4700 C216 C483 7.5V
4.7u 1000
Y
C810 R805
100
10u
+8V
R482 R456
10K 100K
V-DY
D481
IN4148
N501 R466
EL817 +B R482 C484 560K
1/4W-150K R457 2.2k 500V-102 5
R557 3.9K
D501-D504 RL207 X 4
C503-C506 1000P/1KV X 4 R570 4
47K H-DY
D551 C552 R559 V552 D562
1KV-471 C561 100K 6V2
C1815
D502
D503
3
HER207
C511
C504
220u/160V
C505
C507
100u/400V X
R503 2
100K RP501 R574
D504
D501
5.6K
C503
C506
2.2K/1W
BCK N401 R561
T501 +24V X 1W0.39
N502 C305 R454 C456 !
13 LA78040A !
4
5Q0765 270/1W C403
R504 HER207 T451 T401
R502 150K C401 ST1803 X 4
5W-1.8 D554 R552 1W0.39 1000u/25V D451
12 35V-47UF V451 BY228 BSC25-N0416
C455
2KV-912 C486 R459 2
INV IN
VCC1
PNMP UP
VEE
V OUT
VCC2
NON INV IN
HER207 C303
1
2
3
4
5
R402 33 27K 12
9 D553 104 1K 1/2W XS404
1W0.39 100 D452 C459 2 3
1
2
3
4
5
6
7
RT501
D563 FR107 8.2 +12V R404
R501 16 2.7K R303 7
22K 1/2W
10K
104
MZ72-18RM
SW501 C510 1015 C558 C556 R314 XS403
470PF R567 V562 FR107
470UF 103 R316 R319 R320 V303
8.2K 270K 47K R323 D2012
180V 1
XS501 R514 1K 18K 3.9K
XS502
12M 1/2W R553 V311 GND 2
10K D550 1815 R480
47u/35V RT-2W-1
D559 R723
HEAT 3
9.1V R568 1K IN4148 10K
C517 R311
AC400V 2200P 39K C314 4
R566 D558 V561 R317 C315 VR311 VR312 10K
C1815 470u/25V R318 D401
L801 8.2K IN4148 1K 50K C313 FR155
AC220V 2.2K R550
50Hz DGC-HL-29 #47u/35V C402 1/4W-330K
250V-10UF
+8V
R481
5.6K