Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
TEST REPORT
IEC 62040-1
Uninterruptible power systems (UPS) –
Part 1: General and safety requirements for UPS
If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB
Scheme procedure shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory
and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
Rating of UPS:
SRT3000RMXLI-IEC ,
SRT2200RMXLI-IEC
SRT3000XLW-IEC
SRT3000XLW-IEC
A B C D see Model Matrix (Appendix
Input 208-240Vac, 50/60Hz; Output 3000VA, 2700W
Summary of testing:
Note: EN Group Differences together with National Differences and Special National Conditions, if any, are in
the Appendix to the main body of this TRF.
Summary of testing:
Clause 4.5 Components ........................................................................................: Pass N/A
Clause 4.6 Power interface ...................................................................................: Pass N/A
Clause 4.7 Markings and instructions....................................................................: Pass N/A
Clause 5.1 Protection from electric shock and energy hazards ............................: Pass N/A
Clause 5.2 Requirements for auxiliary circuits ....................................................... Pass N/A
Clause 5.2.2 Telephone network voltage circuits – TNV........................................... Pass N/A
Clause 5.2.3 Limited current circuits ......................................................................... Pass N/A
Clause 5.2.4 External signalling circuits Pass N/A
Clause 5.3 Provisions for earthing and bonding ..................................................... Pass N/A
Clause 5.4 AC and D.C. power isolation ................................................................ Pass N/A
Clause 5.5 Overcurrent and earth fault protection ................................................. Pass N/A
Clause 5.6 Protection of personnel – Safety interlocks .......................................... Pass N/A
Clause 2.9 Electrical insulation ..............................................................................: Pass N/A
Clause 5.7 Clearances, creepage distances and distances through insulation ..... Pass N/A
Clause 6.2 Connection to power ............................................................................ Pass N/A
Clause 6.3 Wiring terminals for external power conductors ................................... Pass N/A
Clause 3.3 Wiring terminals for connection of external conductors ....................... Pass N/A
Clause 7 Physical requirements Pass N/A
Clause 7.5 Resistance to fire Pass N/A
Clause 7.7 Temperature rise Pass N/A
Clause 8 Electrical requirements and simulated abnormal conditions Pass N/A
Clause 8.1 earth leakage Pass N/A
Clause 8.2 Electric strength Pass N/A
Clause 8.3 Abnormal operating and fault conditions Pass N/A
Annex A Tests for resistance to heat and fire Pass N/A
Annex B Motor Tests under abnormal conditions Pass N/A
Annex C Transformers Pass N/A
Annex G Alternative Method for determining minimum clearances Pass N/A
Annex M Ventilation of battery compartments Pass N/A
Annex U Insulated winding wires for use without interleaved insulation Pass N/A
Annex V AC Power Distribution Systems Pass N/A
Conditions of Installation:
The units are suitable for a maximum manufacturer’s recommended ambient operating temperature (Tma)
of 40 °C.
Unit is designed and approved for use in installation category II.
Unit intended for continuous operation while charging.
UPS are Class 1 and designed for Pollution Degree 2.
Unit could be used as stand-alone (tower) or rack mounted version.
VDE approved appliance inlets and outlets are used.
– Alternative construction for AC power input and/or output power outlet to be terminal block struc-
ture. See installation manual for detail.
Secondary circuits are designed in 3 areas, (MB + DCLPS board and Communication Boards) other boards
are defined as Primary circuit area.
Model differences:
All models are identical except:
UPS, Main differences:
1. Electric Ratings
2. Transformers: Charger transformer, DC/DC transformer, and Logic Power Supply transformer
3. Chokes: Input choke (for EMI), PFC choke L1203, Inverter choke L1207
4. TRIAC (for improving relay transfer time), Hall Sensor (for current sense)
5. Size of PCB (2.2KVA is 2 inch shorter than 3KVA). Layout in the area of PFC choke, Inverter
choke.
Appendix 1 Pictures 50 - 54
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
7 PHYSICAL REQUIREMENTS P
7.1 Enclosure P
7.2 Stability P
4.1/RD
IEC 62040
Clause Requirement – Test Result – Remark Verdict
Angle of 10° P
Test force (N) ..........................................................: P
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
4.7.3.3/RD Materials for components and other parts outside Front Bezel rated HB P
fire enclosures (for decorative only); Bezel for
Display (UI interface) is rated
HB (LPS circuits are complied.)
4.7.3.4/RD Materials for components and other parts inside fire All internal materials are rated P
enclosures V-2 or better, or are mounted
on printed wiring boards rated
V-1 or better
4.7.3.5/RD Materials for air filter assemblies No air filter assemblies N/A
4.7.3.6/RD Materials used in high-voltage components No high-voltage components N/A
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
M/RD ANNEX M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1/RD) N/A
M.1/RD Introduction N/A
M.2 /RD Method A N/A
M.3/RD Method B N/A
M.3.1/RD Ringing signal N/A
M.3.1.1/RD Frequency (Hz) ........................................................: ⎯
M.3.1.2/RD Voltage (V) ...............................................................: ⎯
M.3.1.3/RD Cadence; time (s), voltage (V) .................................: ⎯
M.3.1.4/RD Single fault current (mA) ..........................................: ⎯
M.3.2/RD Tripping device and monitoring voltage ..................: N/A
M.3.2.1/RD Conditions for use of a tripping device or a monitor- ⎯
ing voltage
M.3.2.2/RD Tripping device N/A
M.3.2.3/RD Monitoring voltage (V) .............................................: N/A
IEC 62040
Clause Requirement – Test Result – Remark Verdict
B/RD ANNEX B, P
MOTOR TESTS UNDER ABNORMAL CONDITIONS (see 4.7.2.2/RD and 5.3.2/RD)
B.1/RD General requirements DC fans used P
Position ....................................................................: See Components List ⎯
Manufacturer ...........................................................: See Components List ⎯
Type .........................................................................: See Components List ⎯
Rated values ..........................................................: See Components List ⎯
B.2/RD Test conditions P
B.3/RD Maximum temperatures See Test result for details. P
B.4/RD Running overload test N/A
B.5/RD Locked-rotor overload test N/A
Test duration (days) ................................................: ⎯
Electric strength test: test voltage (V) .....................: ⎯
B.6/RD Running overload test for d.c. motors in secondary Fans are VDE or TUV certi- P
circuits fied to IEC/EN60950-1
B.6.1/RD General See B.6 P
B.6.2/RD Test procedure See B.6 P
B.6.3/RD Alternative test procedure See B.6 P
B.6.4/RD Electric strength test; test voltage (V) .....................: See B.6 P
B.7/RD Locked-rotor overload test for d.c. motors in sec- Fans are VDE certified to P
IEC 62040
Clause Requirement – Test Result – Remark Verdict
D/RD ANNEX D P
MEASURING INSTRUMENTS FOR TOUCH CURRENT TESTS (see 5.1.4/RD)
D.1/RD Measuring instrument N/A
D.2/RD Alternative measuring instrument P
IEC 62040
Clause Requirement – Test Result – Remark Verdict
H ANNEX H, N/A
GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER AND
FOREIGN OBJECTS (see IEC 60529)
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
AUX Charger Trans- APC 433- Class B IEC 60950-1 Tested within
former (T1201) 0133XXXXXXXX equipment
SRT3000XLI, XX
SRT3000RMXLI
(X can be any al-
phanumeric, +, *,
#, _, - or blank)
AUX Charger Trans- APC 433- Class B IEC 60950-1 Tested within
former (T1201) 0123XXXXXXXX equipment
SRT2200XLI, XX
SRT2200RMXL
(X can be any al-
phanumeric, +, *,
#, _, - or blank)
DC to DC transform- APC 433- Class B IEC 60950-1 Tested within
er (T1203) 0135XXXXXXXX equipment
XX
SRT3000XLI,
SRT3000RMXLI (X can be any al-
phanumeric, +, *,
#, _, - or blank)
DC to DC transform- APC 433- Class B IEC 60950-1 Tested within
er (T1203) 0130XXXXXXXX equipment
XX
SRT2200XLI,
SRT2200RMXL (X can be any al-
phanumeric, +, *,
#, _, - or blank)
Current Sense APC 460-1003 Class B IEC 60950-1 Tested within
Transformer XXXXXXXXXX equipment
(CT1200)
(X can be any al-
phanumeric, +, *,
#, _, - or blank)
Current Sense APC 460-1032 Class B IEC 60950-1 Tested within
Transformer XXXXXXXXXX equipment
(CT1201)
(X can be any al-
phanumeric, +, *,
#, _, - or blank)
Current Sense APC 460-1006 Class B IEC 60950-1 Tested within
Transformer XXXXXXXXXX equipment
(CT1202)
(X can be any al-
phanumeric, +, *,
#, _, - or blank)
Transformer (T1200) APC 430-7205 Class B IEC 60950-1 Tested within
XXXXXXXXXX equipment
(430-7205-Z)
(X can be any al-
phanumeric, +, *,
#, _, - or blank)
Backfeed Relay Song Chuan 832A-1A-F-C-H- 20A, 250Vac EN 61810-1 6615 (VDE)
(RY1205) 24VDC Coil 24 Vdc UL60947-1 E88991 (UL)
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
Optical Isolator ( AVAGO Tech- 6N137-360E (for Single channel, IEC/EN 60747-5- 40009430 (VDE)
IC1707, IC1708, nologies Tube) 1000V 5
IC1711, IC1712)
6N137-560E (for /us, 630V
(349-0137-Z-001) Tape and Reel)
Battery Pack
Fuse (F1, F2) COOPER MDA-V-R 250Vac, 30A UL 248-14 E19180 (UL)
BUSSMANN
(512-0030-Z)
Battery CSB HR1221W 12V, 21W UL 1989 MH14533(UL)
(910-6003-001) B&B BP5-12 12V, 5Ah MH19884(UL)
Case LG AF312A 5V, 2.1mm min. UL746C E67171 (UL)
(876-1046)
(876-1047)
IEC 62040
Clause Requirement – Test Result – Remark Verdict
Battery Pack
Fuse (F1, F2) COOPER MDA-V-R 250Vac, 30A UL 248-14 E19180 (UL)
(512-0030-Z) BUSSMANN
Battery KUNG LONG WP5-12 12V, 5Ah UL 1989 MH16982 (UL)
(910-6003-001)
B&B BP5-12 12V, 5Ah MH19884(UL)
6 or 8 used *)
Case LG AF312A 5V, 2.1mm min. UL746C E67171 (UL)
(876-1046)
(876-1047)
1
) an asterisk indicates a mark which assures the agreed level of surveillance
*) Number of batteries: 6 for battery pack SRT72BP, SRT72RMBP or 8 for SRT96BP, SRT96RMBP
1
) an asterisk indicates a mark which assures the agreed level of surveillance
Supplementary information:
Note(s):
IEC 62040
Clause Requirement – Test Result – Remark Verdict
Supplementary information:
Supplementary information:
Supplementary information:
IEC 62040
Clause Requirement – Test Result – Remark Verdict
Supplementary information:
Supplementary information:
IEC 62040
Clause Requirement – Test Result – Remark Verdict
Supplementary information:
Basic / supplementary:
Reinforced:
Supplementary information:
6, 8.2 and TABLE: Electric strength tests, impulse tests and voltage surge tests P
9
Test voltage applied between: Voltage shape Test voltage Breakdown
(AC, DC, im- (V) Yes / No
pulse, surge)
Functional:
Basic / supplementary:
Reinforced:
IEC 62040
Clause Requirement – Test Result – Remark Verdict
Supplementary information:
Supplementary information:
Supplementary information:
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
Construction:
Pin numbers
Prim.
Sec.
Bobbin
Material
Thickness
Electric strength test
With AC 3000V after humidity treatment
Result Pass
Supplementary information: Refer to IEC 60950-1 Test Report (Appendix 3)
IEC 62040
Clause Requirement – Test Result – Remark Verdict
IEC 62040
Clause Requirement – Test Result – Remark Verdict
refer to IEC 60950-1 Test Report / Liste of test equipment used (Appendix 7)
Supplementary information:
Battery Pack
METHOD A
A sample of each model indicated below was operated in the normal mode, and the input was
measured using suitable meters.
METHOD B
Same as Method A except the unit was operated in the recharge mode.
METHOD C
Same as Method A except the unit was operated in the Stored Energy Mode.
METHOD D
Same as Method A except the unit was operated in the bypass mode.
RESULTS
INPUT
Rated Measured
AC 50 Hz
Remote
Model Method
Battery V (A) (kVA) (W) (P.F.)
V (A) W PF
V A
A 208 16 - - - - 208.2 14.3 2957/2924 0.99
B 208 16 - - - - 208.2 15.6 3240/3210 0.99
C - - - - 96 31.1 - - - -
SRT3000(
RM)XLW- - AC 60 Hz - - - - - -
IEC
A 208 16 - - - - 208.1 14.3 2950/2920 0.99
B 208 16 - - - - 208.1 15.5 3225/3210 0.99
C - - - - 96 30.9 - - - -
Rated Measured
AC 50 Hz Remote
Model Method
Battery V (A) (kVA) (W) (P.F.)
V (A) W PF
V A
A 240 20 - - - - 240.2 12.3 2945/2920 0.99
B 240 20 - - - - 240.4 13.5 3220/3180 0.99
C - - - - 96 31.0 - - - -
SRT3000(
RM)XLW- - AC 60 Hz - - - - - -
IEC
A 240 20 - - 106 2 240.2 12.2 2940/2900 0.99
B 240 20 - - 106 2 240.3 13.4 3226/3184 0.99
C - - - - 96 31.0 - - - -
OUTPUT
Rated (50Hz) Measured, AC
Model Method
V (A) (kVA) (W) (P.F.) V (A) (kVA) (W) (P.F.)
The input current [was] [was not] more than 110 percent of rated value.
NOTES:
1. - Applicable only for remote battery supplies; V is the nominal voltage rating of battery supply; A is
the measured value of battery current during Stored Energy Mode when the battery voltage was
equal to the nominal voltage rating.
2. - Applicable only to units intended for connection to a 3-phase, 4-wire supply. A true rms amme-
ter was used.
p= phase;
p-p = phase-to-phase;
p-n = phase-to-neutral.
The sample was connected as noted below and operated until temperatures became stable. Temper-
atures were measured using the thermocouple method.
[ ] Rise in temperature of windings of motors and transformers were additionally determined by the
change-of-resistance method.
[X] Before starting the Heating Test, each special non-detachable power supply cord connection was
pulled with a force of 5 N (1.12 lbs) for one minute. During the Heating Test, the temperature of its
connections were recorded. (Maximum 60°C rise per 3.3.2.)
Method Comments
A sample of each model indicated below was operated in the normal mode under the con-
A ditions described under OPERATING MODES AND CONDITIONS. Each unit was oper-
ated continuously under these conditions until temperatures stabilized.
Same as Method A except each unit was operated in the recharge mode until tempera-
B
tures peaked.
C Same as Method A except each unit was operated in the Stored Energy Mode.
D Same as Method A except each unit was operated in the bypass mode.
[ ] The concentration of hydrogen gas in the battery compartment was measured during the test - see
Battery Compartment Ventilation Test on following pages for method and results.
Tmra was __40___ °C.
Test Conditions:
Model Method Input V Input Hz or DC
SRT3000(RM)XLW-IEC A 187, 208,240,254.4 60
B 187, 208,240,254.4 60
C 96 DC
D 187, 208,240,254.4 60
Note: (#) - All the measured data has been normalized to ambient 40ºC.
Note: (@) - If 60 Hz in “Input Test” is the most severe operating condition, then please replace fre-
quency in 60 Hz for “Heating Test”.
RESULTS
Model SRT3000RMXLW-IEC, I/P: 208 V ac, 50 Hz, O/P: 3000 VA, 2700 W
Maximum Measured Temperature, °C
Thermocouple Location Method / Mode
A A# B B# C C# Limit
1. D1238 40.6 52.2 41.9 53.3 37.5 49.6 -
2. C1226 47.5 59.1 49.9 61.3 41.1 53.2 85
3. C1211 40.4 52.0 41.7 53.1 37.9 50.0 85
4. C1227 57.2 68.8 61.7 73.1 56.7 68.8 85
5. L1200 coil 51.8 63.4 55.4 66.8 42.2 54.3 90
6. L1206 coil 61.9 73.5 66.7 78.1 51.1 63.2 90
7. PCB near Q1211 41.6 53.2 42.9 54.3 37.9 50.0 90
8. T1201 coil 43.5 55.1 45.0 56.4 38.9 51.0 90
9. T1201 core 43.2 54.8 44.7 56.1 39.2 51.3 90
10. CT1200 coil 59.5 71.1 63.2 74.6 54.2 66.3 90
11. CT1200 core 59.7 71.3 63.5 74.9 54.7 66.8 90
12. C1200 50.0 61.6 54.0 65.4 50.4 62.5 90
13. L1208 coil 61.0 72.6 64.6 76.0 57.2 69.3 90
14. RY1200 coil 50.4 62.0 50.9 62.3 62.2 74.3 90
15. PCB near IC1202 59.3 70.9 62.9 74.3 54.0 66.1 90
16. PCB near IC1203 53.2 64.8 56.5 67.9 44.3 56.4 90
17. T802 coil 33.6 45.2 36.6 48.0 34.8 46.9 90
18. Q1218 Heat-sink 66.5 78.1 70.9 82.3 66.5 78.6 90
19. L1203 coil 63.2 74.8 68.2 79.6 50.1 62.2 90
20. T701 coil 55.8 67.4 57.7 69.1 49.6 61.7 90
21. T701 core 55.8 67.4 57.6 69.0 49.7 61.8 90
22. L1207 coil 83.4 95.0 86.9 98.3 77.3 89.4 110
23. PCB near Q1223 48.7 60.3 51.5 62.9 40.6 52.7 90
24. PCB near Q1220 49.8 61.4 53.3 64.7 39.3 51.4 90
25. RY1202 coil 53.5 65.1 56.9 68.3 47.9 60.0 90
26. RY1203 coil 83.9 95.5 87.1 98.5 78.2 90.3 110
27. RY1204 coil 46.3 57.9 48.3 59.7 41.7 53.8 90
28. RY1205 coil 78.0 89.6 81.3 92.7 47.5 59.6 110
29. RY1206 coil 70.2 81.8 72.8 84.2 43.6 55.7 90
30. C1268 32.8 44.4 34.4 45.8 41.5 53.6 85
31. C1269 36.8 48.4 38.0 49.4 42.7 54.8 85
32. L1202 coil 33.3 44.9 36.3 47.7 47.2 59.3 90
33. L1201 coil 30.7 42.3 34.0 45.4 42.7 54.8 90
Model SRT3000RMXLW-IEC, Input: 240 V ac, 50 Hz, O/P: 3000 VA, 2700 W
Maximum Measured Temperature, °C
Thermocouple Location Method / Mode
A A# B B# C C# Limit
1. D1238 38.9 51.4 38.0 51.5 38.3 50.8 -
2. C1226 44.2 56.7 44.2 57.7 40.9 53.4 85
3. C1211 38.4 50.9 37.5 51.0 38.7 51.2 85
4. C1227 51.4 63.9 53.6 67.1 52.3 64.8 85
5. L1200 coil 47.2 59.7 48.2 61.7 41.5 54.0 90
6. L1206 coil 54.4 66.9 57.0 70.5 48.7 61.2 90
7. PCB near Q1211 40.6 53.1 39.7 53.2 38.7 51.2 90
8. T1201 coil 45.3 57.8 44.4 57.9 39.8 52.3 90
9. T1201 core 42.3 54.8 41.6 55.1 40.1 52.6 90
10. CT1200 coil 53.2 65.7 54.7 68.2 51.2 63.7 90
11. CT1200 core 53.3 65.8 54.9 68.4 51.5 64.0 90
12. C1200 45.6 58.1 47.6 61.1 47.7 60.2 90
13. L1208 coil 54.3 66.8 55.9 69.4 53.3 65.8 90
14. RY1200 coil 49.2 61.7 48.0 61.5 64.1 76.6 90
15. PCB near IC1202 52.6 65.1 53.9 67.4 50.7 63.2 90
16. PCB near IC1203 48.1 60.6 48.9 62.4 42.8 55.3 90
17. T802 coil 32.3 44.8 33.4 46.9 34.9 47.4 90
18. Q1218 Heat-sink 58.2 70.7 60.1 73.6 59.2 71.7 90
19. L1203 coil 55.3 67.8 57.1 70.6 47.4 59.9 90
20. T701 coil 52.6 65.1 52.1 65.6 50.6 63.1 90
21. T701 core 52.5 65.0 52.2 65.7 50.6 63.1 90
22. L1207 coil 70.0 82.5 71.1 84.6 66.8 79.3 110
23. PCB near Q1223 44.2 56.7 44.2 57.7 42.1 54.6 90
24. PCB near Q1220 45.3 57.8 45.4 58.9 40.4 52.9 90
25. RY1202 coil 48.6 61.1 49.6 63.1 45.6 58.1 90
26. RY1203 coil 78.2 90.7 79.3 92.8 76.2 88.7 110
27. RY1204 coil 43.1 55.6 42.8 56.3 40.7 53.2 90
28. RY1205 coil 73.8 86.3 74.6 88.1 48.2 60.7 110
29. RY1206 coil 66.5 79.0 67.0 80.5 44.4 56.9 90
30. C1268 30.9 43.4 33.3 46.8 42.7 55.2 85
31. C1269 34.2 46.7 34.8 48.3 43.7 56.2 85
32. L1202 coil 31.7 44.2 33.0 46.5 49.1 61.6 90
33. L1201 coil 29.6 42.1 31.2 44.7 44.5 57.0 90
Model SRT3000RMXLW-IEC, Input: 254.4 V ac, 50 Hz, O/P: 3000 VA, 2700 W
Maximum Measured Temperature, °C
Thermocouple Location Method / Mode
A A# B B# C C# Limit
1. D1238 39.0 51.1 41.4 52.9 39.3 51.1 -
2. C1226 43.5 55.6 46.8 58.3 42.0 53.8 85
3. C1211 38.3 50.4 40.6 52.1 39.8 51.6 85
4. C1227 51.0 63.1 56.3 67.8 53.4 65.2 85
5. L1200 coil 46.2 58.3 50.3 61.8 43.8 55.6 90
6. L1206 coil 53.4 65.5 58.9 70.4 49.8 61.6 90
7. PCB near Q1211 42.3 54.4 44.8 56.3 41.6 53.4 90
8. T1201 coil 50.4 62.5 53.8 65.3 49.4 61.2 90
9. T1201 core 44.1 56.2 47.1 58.6 42.6 54.4 90
10. CT1200 coil 52.6 64.7 57.2 68.7 52.3 64.1 90
11. CT1200 core 52.8 64.9 57.5 69.0 52.6 64.4 90
12. C1200 45.4 57.5 50.4 61.9 48.8 60.6 90
13. L1208 coil 53.7 65.8 58.4 69.9 54.5 66.3 90
14. RY1200 coil 49.1 61.2 50.5 62.0 65.2 77.0 90
15. PCB near IC1202 51.8 63.9 56.3 67.8 51.8 63.6 90
16. PCB near IC1203 47.0 59.1 50.8 62.3 44.2 56.0 90
17. T802 coil 32.2 44.3 36.2 47.7 35.9 47.7 90
18. Q1218 Heat-sink 57.8 69.9 63.0 74.5 60.4 72.2 90
19. L1203 coil 53.3 65.4 58.3 69.8 49.2 61.0 90
20. T701 coil 51.7 63.8 54.3 65.8 51.6 63.4 90
21. T701 core 51.8 63.9 54.4 65.9 51.5 63.3 90
22. L1207 coil 69.4 81.5 74.3 85.8 68.1 79.9 110
23. PCB near Q1223 43.0 55.1 46.4 57.9 43.1 54.9 90
24. PCB near Q1220 44.0 56.1 48.0 59.5 41.5 53.3 90
25. RY1202 coil 47.8 59.9 51.9 63.4 46.3 58.1 90
26. RY1203 coil 77.6 89.7 81.6 93.1 77.0 88.8 110
27. RY1204 coil 42.4 54.5 45.4 56.9 41.7 53.5 90
28. RY1205 coil 72.9 85.0 76.7 88.2 69.0 80.8 110
29. RY1206 coil 65.9 78.0 69.0 80.5 61.8 73.6 90
30. C1268 30.7 42.8 33.4 44.9 43.8 55.6 85
31. C1269 33.6 45.7 35.9 47.4 44.8 56.6 85
32. L1202 coil 31.6 43.7 35.8 47.3 50.0 61.8 90
33. L1201 coil 29.6 41.7 34.1 45.6 45.4 57.2 90
Model SRT3000XLW-IEC, Input: 187.2 V ac, 50 Hz, O/P: 3000 VA, 2700 W
Maximum Measured Temperature, °C
Thermocouple Location Method / Mode
A A# B B# C C# Limit
1. D1238 38.9 53.6 40.8 55.6 39.2 53.7 -
2. C1226 47.8 62.5 51.4 66.2 47.6 62.1 85
3. C1211 39.0 53.7 41.0 55.8 39.0 53.5 85
4. C1227 56.6 71.3 61.1 75.9 57.7 72.2 85
5. L1200 coil 52.8 67.5 58.0 72.8 51.1 65.6 90
6. L1206 coil 62.8 77.5 68.9 83.7 60.1 74.6 90
7. PCB near Q1211 40.1 54.8 42.1 56.9 40.4 54.9 90
8. T1201 coil 42.0 56.7 44.4 59.2 42.1 56.6 90
9. T1201 core 42.0 56.7 44.4 59.2 41.6 56.1 90
10. CT1200 coil 58.8 73.5 63.4 78.2 57.5 72.0 90
11. CT1200 core 58.9 73.6 63.6 78.4 57.6 72.1 90
12. C1200 48.3 63.0 52.8 67.6 50.5 65.0 90
13. L1208 coil 60.5 75.2 65.1 79.9 59.4 73.9 90
14. RY1200 coil 48.2 62.9 48.9 63.7 62.5 77.0 90
15. PCB near IC1202 58.4 73.1 63.2 78.0 57.1 71.6 90
16. PCB near IC1203 53.4 68.1 58.2 73.0 52.1 66.6 90
17. T802 coil 31.6 46.3 35.1 49.9 34.4 48.9 90
18. Q1218 Heat-sink 65.1 79.8 69.9 84.7 66.3 80.8 90
19. L1203 coil 65.5 80.2 72.3 87.1 63.1 77.6 90
20. T701 coil 55.1 69.8 57.7 72.5 54.9 69.4 90
21. T701 core 55.2 69.9 57.8 72.6 54.9 69.4 90
22. L1207 coil 82.3 97.0 86.7 101.5 76.5 91.0 110
23. PCB near Q1223 48.9 63.6 52.9 67.7 45.2 59.7 90
24. PCB near Q1220 50.8 65.5 55.4 70.2 46.5 61.0 90
25. RY1202 coil 53.2 67.9 57.5 72.3 53.1 67.6 90
26. RY1203 coil 83.3 98.0 87.3 102.1 83.2 97.7 110
27. RY1204 coil 45.7 60.4 48.8 63.6 45.7 60.2 90
28. RY1205 coil 79.0 93.7 83.5 98.3 79.0 93.5 110
29. RY1206 coil 70.7 85.4 74.7 89.5 70.3 84.8 90
30. C1268 30.9 45.6 35.2 50.0 41.1 55.6 85
31. C1269 35.6 50.3 37.3 52.1 42.5 57.0 85
32. L1202 coil 31.5 46.2 35.6 50.4 49.6 64.1 90
33. L1201 coil 28.8 43.5 33.1 47.9 45.1 59.6 90
Model SRT3000XLW-IEC, Input: 208 V ac, 50 Hz, O/P: 3000 VA, 2700 W
Maximum Measured Temperature, °C
Thermocouple Location Method / Mode
A A# B B# C C# Limit
1. D1238 39.1 51.6 42.9 52.3 38.3 50.9 -
2. C1226 47.0 59.5 51.4 60.8 45.9 58.5 85
3. C1211 39.0 51.5 42.8 52.2 38.3 50.9 85
4. C1227 56.6 69.1 62.2 71.6 58.1 70.7 85
5. L1200 coil 51.1 63.6 56.7 66.1 48.1 60.7 90
6. L1206 coil 61.4 73.9 68.1 77.5 56.8 69.4 90
7. PCB near Q1211 40.1 52.6 43.9 53.3 39.4 52.0 90
8. T1201 coil 41.9 54.4 45.7 55.1 40.9 53.5 90
9. T1201 core 41.6 54.1 45.5 54.9 40.4 53.0 90
10. CT1200 coil 58.6 71.1 64.1 73.5 57.4 70.0 90
11. CT1200 core 58.8 71.3 64.4 73.8 57.6 70.2 90
12. C1200 48.7 61.2 54.3 63.7 51.0 63.6 90
13. L1208 coil 60.6 73.1 66.1 75.5 59.3 71.9 90
14. RY1200 coil 48.8 61.3 52.0 61.4 63.4 76.0 90
15. PCB near IC1202 58.1 70.6 63.5 72.9 56.6 69.2 90
16. PCB near IC1203 51.8 64.3 57.2 66.6 49.8 62.4 90
17. T802 coil 32.6 45.1 37.3 46.7 35.1 47.7 90
18. Q1218 Heat-sink 65.6 78.1 71.3 80.7 66.9 79.5 90
19. L1203 coil 62.3 74.8 68.9 78.3 58.5 71.1 90
20. T701 coil 54.2 66.7 58.2 67.6 53.2 65.8 90
21. T701 core 54.3 66.8 58.2 67.6 53.2 65.8 90
22. L1207 coil 82.6 95.1 87.6 97.0 78.4 91.0 110
23. PCB near Q1223 47.3 59.8 52.2 61.6 41.6 54.2 90
24. PCB near Q1220 49.1 61.6 54.5 63.9 42.6 55.2 90
25. RY1202 coil 52.1 64.6 57.5 66.9 51.5 64.1 90
26. RY1203 coil 82.6 95.1 87.5 96.9 81.8 94.4 110
27. RY1204 coil 44.8 57.3 49.2 58.6 44.3 56.9 90
28. RY1205 coil 77.0 89.5 82.3 91.7 68.6 81.2 110
29. RY1206 coil 69.1 81.6 74.0 83.4 61.6 74.2 90
30. C1268 31.2 43.7 34.7 44.1 41.6 54.2 85
31. C1269 35.2 47.7 38.8 48.2 43.1 55.7 85
32. L1202 coil 32.3 44.8 37.8 47.2 50.2 62.8 90
33. L1201 coil 29.7 42.2 35.7 45.1 45.7 58.3 90
Model SRT3000XLW-IEC, Input: 240 V ac, 50 Hz, O/P: 3000 VA, 2700 W
Maximum Measured Temperature, °C
Thermocouple Location Method / Mode
A A# B B# C C# Limit
1. D1238 41.2 52.7 39.9 52.9 38.3 50.6 -
2. C1226 48.2 59.7 46.7 59.7 41.1 53.4 85
3. C1211 40.6 52.1 39.5 52.5 38.9 51.2 85
4. C1227 56.6 68.1 55.9 68.9 53.5 65.8 85
5. L1200 coil 50.7 62.2 50.5 63.5 41.1 53.4 90
6. L1206 coil 59.4 70.9 59.6 72.6 49.9 62.2 90
7. PCB near Q1211 42.1 53.6 41.9 54.9 38.8 51.1 90
8. T1201 coil 46.1 57.6 47.1 60.1 39.9 52.2 90
9. T1201 core 43.0 54.5 43.9 56.9 40.3 52.6 90
10. CT1200 coil 58.9 70.4 57.1 70.1 52.0 64.3 90
11. CT1200 core 58.9 70.4 57.3 70.3 52.3 64.6 90
12. C1200 50.4 61.9 49.8 62.8 48.5 60.8 90
13. L1208 coil 61.1 72.6 58.6 71.6 54.4 66.7 90
14. RY1200 coil 50.3 61.8 49.3 62.3 63.8 76.1 90
15. PCB near IC1202 58.6 70.1 56.1 69.1 51.2 63.5 90
16. PCB near IC1203 52.3 63.8 50.8 63.8 42.9 55.2 90
17. T802 coil 34.9 46.4 35.5 48.5 35.4 47.7 90
18. Q1218 Heat-sink 64.1 75.6 62.6 75.6 59.8 72.1 90
19. L1203 coil 61.0 72.5 59.2 72.2 45.2 57.5 90
20. T701 coil 55.3 66.8 53.7 66.7 50.7 63.0 90
21. T701 core 55.2 66.7 53.8 66.8 50.6 62.9 90
22. L1207 coil 76.6 88.1 73.8 86.8 67.9 80.2 110
23. PCB near Q1223 44.8 56.3 46.3 59.3 42.1 54.4 90
24. PCB near Q1220 46.5 58.0 48.2 61.2 40.7 53.0 90
25. RY1202 coil 53.7 65.2 51.4 64.4 44.9 57.2 90
26. RY1203 coil 84.3 95.8 81.0 94.0 76.1 88.4 110
27. RY1204 coil 46.4 57.9 44.9 57.9 40.8 53.1 90
28. RY1205 coil 76.8 88.3 76.5 89.5 47.0 59.3 110
29. RY1206 coil 68.2 79.7 69.2 82.2 43.4 55.7 90
30. C1268 32.7 44.2 35.8 48.8 42.1 54.4 85
31. C1269 36.7 48.2 37.4 50.4 43.5 55.8 85
32. L1202 coil 34.1 45.6 35.6 48.6 50.4 62.7 90
33. L1201 coil 31.3 42.8 33.8 46.8 46.3 58.6 90
Model SRT3000XLW-IEC, Input: 254.4 V ac, 50 Hz, O/P: 3000 VA, 2700 W
Maximum Measured Temperature, °C
Thermocouple Location Method / Mode
A A# B B# C C# Limit
1. D1238 39.8 51.9 40.7 52.8 39.5 51.0 -
2. C1226 44.8 56.9 46.5 58.6 44.3 55.8 85
3. C1211 39.2 51.3 40.1 52.2 39.9 51.4 85
4. C1227 52.1 64.2 56.0 68.1 54.1 65.6 85
5. L1200 coil 47.4 59.5 49.9 62.0 45.6 57.1 90
6. L1206 coil 54.9 67.0 58.9 71.0 51.5 63.0 90
7. PCB near Q1211 43.3 55.4 43.9 56.0 42.8 54.3 90
8. T1201 coil 51.8 63.9 52.6 64.7 49.3 60.8 90
9. T1201 core 45.2 57.3 46.1 58.2 44.6 56.1 90
10. CT1200 coil 53.7 65.8 56.9 69.0 52.7 64.2 90
11. CT1200 core 53.9 66.0 57.1 69.2 53.0 64.5 90
12. C1200 46.4 58.5 49.9 62.0 49.1 60.6 90
13. L1208 coil 55.1 67.2 58.5 70.6 55.1 66.6 90
14. RY1200 coil 49.4 61.5 50.0 62.1 64.6 76.1 90
15. PCB near IC1202 52.6 64.7 55.7 67.8 51.8 63.3 90
16. PCB near IC1203 47.7 59.8 50.1 62.2 46.4 57.9 90
17. T802 coil 33.1 45.2 35.9 48.0 36.1 47.6 90
18. Q1218 Heat-sink 58.9 71.0 62.6 74.7 60.4 71.9 90
19. L1203 coil 54.1 66.2 57.5 69.6 51.6 63.1 90
20. T701 coil 52.5 64.6 53.7 65.8 51.9 63.4 90
21. T701 core 52.5 64.6 53.8 65.9 52.1 63.6 90
22. L1207 coil 70.4 82.5 73.5 85.6 68.6 80.1 110
23. PCB near Q1223 43.8 55.9 45.9 58.0 43.0 54.5 90
24. PCB near Q1220 45.3 57.4 47.7 59.8 41.7 53.2 90
25. RY1202 coil 48.6 60.7 51.1 63.2 48.4 59.9 90
26. RY1203 coil 78.2 90.3 80.7 92.8 77.5 89.0 110
27. RY1204 coil 43.3 55.4 44.8 56.9 43.2 54.7 90
28. RY1205 coil 73.8 85.9 76.0 88.1 66.7 78.2 110
29. RY1206 coil 67.0 79.1 69.0 81.1 60.6 72.1 90
30. C1268 31.3 43.4 32.5 44.6 43.0 54.5 85
31. C1269 34.3 46.4 35.1 47.2 44.4 55.9 85
32. L1202 coil 32.6 44.7 36.1 48.2 51.3 62.8 90
33. L1201 coil 30.6 42.7 34.6 46.7 47.1 58.6 90
METHOD
A sample of each model UPS indicated below was operated in the normal mode delivering maximum
rated output AC power into an adjustable resistive load.
[Once the sample reached thermal stability, the unit was operated in the Stored Energy Mode.]
The output was connected to a variable resistor to draw the maximum available output current with all
other outputs loaded to maximum normal rating. If the unit employed foldback or overcurrent circuitry,
the output current was adjusted to a level that was just below the point at which the power supply cir-
cuitry limited the output current. The trip point of overcurrent protective devices was considered to be
110 percent of their current rating; such devices were removed for this test and replaced with an am-
meter. If the unit employed an overtemperature device, the output current was adjusted to a level that
was just below the point at which the overtemperature device operated.
If the initial point selected (below foldback) caused the power supply to foldback after several minutes,
a point (10-20 percent) below foldback was selected. Temperatures were allowed to stabilize and us-
ing a stepwise procedure, the load was increased while monitoring temperatures. After temperatures
stabilized, the load was increased to the next incremental point. The process was continued until fold-
back. The maximum temperature obtained before foldback was recorded. This same stepwise incre-
mental procedure was used for units employing overtemperature protective service.
The equipment was operated until ultimate results (e.g., component opens, fire, etc.) or thermal equi-
librium was obtained. If any test was terminated by opening of a component other than a reliable
component (e.g., Listed/Recognized fuse, Recognized fusing resistor), the test was retested an addi-
tional two times (three times total) using new components as necessary.
RESULTS
Input AC Electric
Unit Model Observations
Voltage, Hz Strength, Pass
1. Output was loaded with 12.2A till temp
stability.
2. Then load up to 18.9A till temp stabil-
ity.
3. Then load up to 20A till temp stability.
4. The load up to 22A, UUT shutdown in-
SRT3000(RM)XLW- stantly, no hazard.
240, 50Hz [Yes] [No]
IEC
Max temp.
1.T1201 coil 50.3°C
2.T1201 core 47.5°C
3.CT1200 coil 57.2°C
4.CT1200 core 57.4°C
TRF No. IEC62040_1ª
VDE Report No. 1924400-3335-0067/203983
Page 77 of 81 VDE Report No.: 203983-AS3-1
Test Results APPENDIX 2
Max temp.
1.T1201 coil 44.7°C
2.T1201 core 45.1°C
3.CT1200 coil 57.4°C
4.CT1200 core 57.4°C
5.T802 coil 44.4°C
Stored energy 6.T701 coil 54.9°C
[Yes] [No]
mode
7.T701 core 56°C
8.T1200 coil 33.5°C
9.T1203 coil 65.7°C
10.T1203 core 74.5°C
11.T1204 coil 42.8°C
12.T1204 core 49.9°C
13.CT1201 coil 50.5°C
14.CT1201 core 49.9°C
15.T1 coil(battery pack) 50.8°C
16.T1 core(battery pack) 50.8°C
17.Ambient 26.1°C
Model Matrix
METHOD
A sample of each model of UPS indicated below was operated in the reserve mode. The backfeed
potentials at the input AC terminals or attachment plug blades were measured. A solid-state device such as
a Triac, SCR, or the like, if provided in the input AC circuit, was shorted at its load terminals during this test.
Voltage Type Maximum Acceptable Voltages
1. Sinusoidal AC, 100 Hz or less 30 V, RMS
2. Non-sinusoidal AC, 100 Hz or less 42.4 V peak
3. Pure DC 60 V
RESULTS
Load Condi- Maximum Leakage Current Q1212 pin2 and pin3 Shorted
Model
tion Line-Line V Line-Ground mA Line-Neutral mA Neutral-Ground mA
SRT3000XLI A -- 0.2 0.01 0.2
B -- 0.2 0.01 0.2
SRT2200XLI A -- 0.2 0.01 0.2
B -- 0.2 0.01 0.2
The maximum voltage available at the input terminals or attachment plug blades [did not exceed] [exceeded]
the indicated maximum acceptable values. For equipment that exceeded the voltage values, a touch current
test was conducted. The maximum measured touch current [did not exceed] [exceeded] 3.5 mA for both no
fault and single fault conditions.