Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
WW
A
B
SECTION
WIPER, WASHER & HORN C
E
CONTENTS
SERVICE INFORMATION ............................ 2 CIGARETTE LIGHTER ...................................... 8 F
Wiring Diagram ......................................................... 8
PRECAUTIONS ................................................... 2
Precaution for Supplemental Restraint System HORN ................................................................. 9 G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Wiring Diagram ......................................................... 9
SIONER" ................................................................... 2 Removal and Installation .......................................... 9
Wiring Diagram and Trouble Diagnosis .................... 2
WIPER & WASHER SWITCH ........................... 11 H
FRONT WIPER AND WASHER .......................... 3 Removal and Installation .........................................11
System Description ................................................... 3
Wiring Diagram ......................................................... 4 WASHER TANK ................................................ 12
I
Removal and Installation ........................................... 4 Removal and Installation .........................................12
Washer Nozzle Adjustment ....................................... 6
Washer Tube Layout ................................................. 7
J
WW
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Wiring Diagram and Trouble Diagnosis INFOID:0000000003492344
WIPER OPERATION B
The wiper switch is controlled by a lever built into the combination switch.
There are two wiper switch positions:
• LO speed C
• HI speed
With the ignition switch in the ON or START position, power is supplied
• through 20A fuse (No. 26, located in the fuse block)
• to wiper motor terminal 1. D
Low and High Speed Wiper Operation
Ground is supplied to wiper switch terminal 17 through body grounds M57 and M61.
With the wiper switch in the LO position, ground is supplied E
• to wiper motor terminal 3
• through wiper switch terminal 14.
With power and ground supplied, the wiper motor operates at low speed.
With the wiper switch in the HI position, ground is supplied F
• to wiper motor terminal 2
• through wiper switch terminal 16.
With power and ground supplied, the wiper motor operates at high speed. G
Auto Stop Operation
When the wiper switch is turned OFF, the wiper motor will continue to operate at low speed until wiper blades
reach windshield base.
H
When wiper blades are not located at base of windshield with wiper switch OFF, ground is supplied
• to wiper motor terminal 3
• through wiper switch terminal 14
• through wiper switch terminal 13 I
• through wiper motor terminal 6
• through wiper motor terminal 4
• through body grounds M57 and M61.
J
WASHER OPERATION
With the ignition switch in the ON or START position, power is supplied
• through 20A fuse (No. 26, located in the fuse block) WW
• to washer motor terminal 1.
When the lever is pulled to the WASH position, ground is supplied
• to washer motor terminal 2
• from wiper switch terminal 18 L
• through wiper switch terminal 17
• through body grounds M57 and M61.
With power and ground supplied, the washer motor operates. M
AALWA0002GB
Wiper Arms
Removal
1. Remove the wiper arm covers.
I
Clearance “L1” : 25 mm (0.98 in) SEL543TA
ALKIA1508GB
2. Remove the wiper motor linkage cover and disconnect linkage at the wiper motor.
CAUTION:
Be careful not to break ball joint rubber boot.
ALKIA1509GB
ALKIA1524GB
4. Remove the wiper pivot nuts (A) and remove the wiper linkage
(1).
ALKIA1510GB
Installation
Installation is the reverse order of removal.
NOTE:
Grease ball joint portion before installation.
Washer Nozzle Adjustment INFOID:0000000003492348
SEL241P
A
Unit: mm (in)
SEL544T
D
J
ALKIA1511GB
AAMWA0010GB
WW
P
AALWA0003GB
HORN
Removal
Revision: March 2008 WW-9 2009 D22 LCV
HORN
< SERVICE INFORMATION >
1. Remove the bolt (A), disconnect the connector (B) and remove
the horn (1).
ALKIA1522GB
Installation
Installation is in the reverse order of removal.
F
ALKIA1523GB
Installation
Installation is in the reverse order of removal. G
WW
WASHER TANK
Removal
1. Remove the LH headlamp assembly. Refer to LT-11, "Removal and Installation".
2. Remove the bolts (A) and remove the washer tank (1).
⇐ :Vehicle front
3. Disconnect the electrical connector and the washer hose.
ALKIA1521GB
Installation
Installation is in the reverse order of removal.