Sei sulla pagina 1di 1

1.

The value of the coefficient of compressibility A measure of the of organic and inorganic acids
for water at ordinary pressure and temperature in the lubricating oil
in kg/cm is equal to
21.000 20. If no resistance is encountered by
displacement, such a subtance is known as
2. A perfect gas Ideal fluid.
None of the above
21. Choose the wrong statement. Alcohol is
3.The value of mass density in kgsecVm4 for used in manometer, because
water at 0oC is Its vapour pressure is low
101.9
22. If mercury in a barometer is repleaced by
4. a vessel is scheduled to enter a SECA during waeter, the height of 3.75 cm of mercury will be
a forthcrning voyage? What additional following cm of water
considerations must a chief engineer take into 51 cm
account when planning for this voyage?
The availability of low sulphur fuel and the 23. the cold room temperature is almost at the
change over time required to ensure the system cut out point in a vapour-compression
is cleaar of normal fuel prior to entry into the refrigeration system. What should the refrigerant
SECA state be just after the evaporator if the system is
correctly set up?
5. the tendency of a liquid surface to contract is Slightly superheated low pressure gas
due to the following properly
Surface tension 24. a fluid in equilibrium can’t sustain
Shear stress
6. which ideal heat engine cycle is the vapour-
compression refrigeneration system based on? 25. Spesific weight of water in S.I. units is equal
The reversed carnot cycle to
9.81 x 103 N/m3
7. the pressure at a point in a fluid will not be the
same in all the directions when the fluid is 26. one of the Main Engine cooling pumps is
Viscous and moving down for maintenance. The rest of the cooling
pumps are opearting near full capacity with
8. how does the maximum oil film pressure in a minimum margins of the maximum temperature
while metal journal bearing operating under full limit. What should be the correct to take with
fluid film conditions compare with the pressure regard to UMS operation
of the lubricating oil supply system Operate the enfinee room on manual mode until
The pressure is greater than the pressure in the the maintenance is completed and the cooling
lubricating system and varies with the journal pump is operational and switched to stand-by
load. mode.

9. surface tension has the units of 27. Choose the correct relationship
New tons/m Kinematicviscosity - dynamicviscosity x density
Dynamicviscosity – kinematicviscosity x density
10. Property of a fluid by which its own
molecules are attracted is called 28. in a static fluid
Cohesion Linear defrmation is small
Fluid pressure is zero
11. which of the following terms is used to Resistance to shear stress is small
describe a thermodynamic process in which no Only normal stresses can exist
heat transfer into or out of the system occurs?
Adiabatic 29. The bulk modulus of elasticity with increase
in pressure
12. a vesel which normally operates with the Increases
engine room in UMS mode is unable to do so
because of defects to some of the critical alarm 30. Kinematic viscosity is dependent upon
functions. What are the main considerations that Density
the Chief Engineer must take into account when
planing alternative arragements to cover the
engine room requirements until the defects are
cleared?
A work rota is estabilished to ensure full
coverage of engine room watchkeeping duties
and adequate rest periods for the engineering
staff.

13. Increase in pressure at the outer edge of a


drum of radius R due to rotation at corad/sec,
full of liquid of density p will be
Pco2/?2/2

14. Which of the following meters is not


associated with viscosity
Orsat

15. A balloon lifting in air follows the following


principle
Archimedes principle
All of the above

16. Mercury does not wet glass. This due to


property of liquid known as
Surface tension

17. Viscosity of water in comparison to mercury


is
Higher

18. For manometer, a better liquid combination


is one having
Higer surface tension

19. What would the result of a TAN test, carried


out on lubricating oil samples from a diesel
engine, indicate?

Potrebbero piacerti anche