Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Revision Record
Version Date Prepared by Change Description
V1.0 13/10/2015 AUGRY Cédric Creation
V1.1 05/04/2016 AUGRY Cédric Update UMPT
1 Introduction.................................................................................................................................3
1.1 SFR IP over E1 Network Structure................................................................................3
1.2 Detail configuration on BTS/Node B..............................................................................3
2 E1 extension................................................................................................................................5
2.1 Scenario1: Target E1 Number <=4 (using WMPT/UMPT bord)................................5
2.1.2 Execute the command of “LST MPLNK”.................................................................5
2.1.3 Execute the command of “DSP E1T1”......................................................................5
2.1.4 Execute the command “ADD MPLNK”....................................................................5
2.1.5 Execute the command “DSP MPLNK”.....................................................................6
1 Introduction
As shown in following demo picture, in SFR Single RAN project, the E1 transmission
carrier of later on Huawei MBTS will be converged by PTC 2/3 to PTC1 OMSN
equipment, and by OMSN to converge E1 to STM-1, then the Cisco router achieve the
transformation from IP over E1 to GE, which means Cisco router will function as the last
hop of MLPPP protocol. The IP over GE traffic will be carried on SFR backbone to each
MBSC site.
Existing test bed Single RAN network infrastructure is shown as follow, which is similar
to the target solution that will be deployed in GC and later on large scale rollout.(2G/3G
co-transmission scenario).
2 E1 extension
Scenario for E1 extension can be defined into two scenarios, when there is more
than 4*E1 required, additional transmission board required which can support
maximum 12*E1.
To find the MPGRP number that we need to add, generally it’s configured as 0;
To find out how many MP link already configured within this MPGRP;
If the command execution is failure with “configuration privilege not obtained” error=>
Execute REQ CMCTRL
4*E1 can be configured on WMPT/UMPT board with Number 0~3; by the command to
check whether the new configured E1 Running status is “Available”.
Add MPLNK to this MPGRP, following demo MML commands to configure MPLNK into
MP group.
It is the Universal Transmission Processing unit (UTRP) board. As the transmission extension
board of the BBU3900, the UTRP provides eight E1s/T1s, one unchannelized STM-1/OC-3 port,
four electrical ports, or two optical ports.
Panels
Figure 2 Panel of the UTRP3, UTRP4, UTRPb4 and UTRPa1 supporting eight E1s/T1s
Figure 5 UTRPc panel (with four electrical ports and two optical ports)
Insert a new UTRP into the slot, and then slide the board until it is in position.
Turn the ejector lever inwards, and then tighten the screws on the panel of the new UTRP.
Connect the cables to the ports on the panel of the new UTRP according to the recorded cable
connections.
Run the DSP BRDVER command to check whether the BootROM or software version of
the new UTRP is correct.
If the BootROM or software version is incorrect, run the ACT SOFTWARE command
to activate the BootROM or software version of the board.
On the LMT, run the DSP BRD command or open Device Panel Management to check board
status. DSP BRD: CN=0, SRN=0, SN=4;
When the board is operational, the RUN LED blinks at 0.5 Hz, and the AL LED is OFF.
If the board works in active mode, the ACT LED is ON. If the board does not work or
works in standby mode, the ACT LED is OFF.
2.2.2 Add E1
PFC=ENABLE, ACFC=ENABLE;
MOD IPPATH:ANI=240,PATHID=0,ITFT=IUB,TXBW=[NEW_BW],RXBW=[NEW_BW];
MOD IPPATH:ANI=240,PATHID=1,ITFT=IUB,TXBW=[NEW_BW],RXBW=[NEW_BW];
MOD IPPATH:ANI=240,PATHID=2,ITFT=IUB,TXBW=[NEW_BW],RXBW=[NEW_BW];
MOD IPPATH:ANI=240,PATHID=3,ITFT=IUB,TXBW=[NEW_BW],RXBW=[NEW_BW];
MOD
IPLOGICPORT:SRN=1,SN=20,BT=GOUc,LPNTYPE=Leaf,LPN=24,BWADJ=OFF,CIR=[NEW
_CIR];