Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Notes on work .................................................. .. . . . . . .Five And removal of the front pillar tweeter, taken
- SRS Air bag, pre-tensioner seat Attach .................................................. ....... . . . 30
Notes on belt with car .............................. Five - Removal of the roof tweeter, mounting ... . . . 31 C
audio .................................................. ..... ...... 6 Super removal of the woofer, mounting ... . . . 31
And electronic tuner radio settings, adjustment .......... ...... 6 And, mounting ................................................. 31
- CD Heck AM / FM Electronic tuner radio and out - Removal of the radio antenna amplifier, Installing
け .................................................. ................. 33
Force signal reference value .................................................. .. Nine
Car Wings correspondence TV / Navigation system ( DVD method) .................................
And video distributor input and output signal reference value ..................... . . . . Ten
34
- BCM Input and output signal reference value .............................. . . . . 11 E
System Overview .............................................. . . . 34
- MD - CD Heck AM / FM Electronic tuner Raj
Unit attention at the time of exchange .................................. 36
Oh input and output signal reference value ................................... . . . . 12
And vehicles warning .............................................. . . . 36
And video distributor input and output signal reference value ..................... . . . . 13
- CAN Communication signal List ........................................ 37
- BCM Input and output signal reference value .............................. . . . . 14
· Component mounting position .......................................... 43 F
- How to proceed with fault diagnosis ....................................... . . . . 15
System FIG. ................................................. . . . 43
- Fault diagnosis .................................................. ... . . . . 16
Antenna configuration diagram ............................................. 44
- Phenomenon by fault diagnosis Chart ................................... Sixteen
·circuit diagram .................................................. ....... . . . 45
And inspection of vehicle noise ....................................... . . . . 17
• Terminal array .................................................. ...... 46
And inspection of the power supply circuit .............................................. Eighteen
G
- Notes on input and output signal reference value measurement ............. 47
Steering wheel electronic switch operation
Tuner radio is not working ................. . . . . 19 - NAVI Control unit input and output signal based on
Absent .................................................. .......... . . . .twenty one Front display unit input and output standards
- No sound from the front speakers only ....... twenty two value .................................................. ................. 52
H
- No sound only from the rear speakers (car - TV Tuner input and output signal reference value .................. 54
Wings correspondence TV / Navigation system ( DVD Method) attaching - BCM Input and output signal reference value ................................. 56
car only) ............................. twenty three - How to proceed with fault diagnosis .......................................... 58
- No sound only from the rear speakers (car · Self-diagnosis function by self-diagnosis menu ......... 58
Wings corresponding twin monitor TV / Navigation system ( DVD - Fault diagnosis function .............................................. . . . 59 I
AV - 1
- NAVI Control unit of the power supply and the earth Front display unit ASSY Minute of
Scan circuit inspection .................................................. . . . 70 Solution, assembly .............................................. . 117
• The power of the front display unit and - TV Remove tuner, mounting ............ . 118
Ground circuit inspection ........................................... . . . 71 Car Wings corresponding twin monitor TV / Navigation system ( DVD
- TV Inspection of the tuner power supply and ground circuit .... 72 method) .................... . 119
- Vehicle speed signal inspection .............................................. . . . 73 System Overview .............................................. . 119
Parking brake signal inspection ..................... . . . 74 Unit attention at the time of exchange ................................ . 121
- IGN Signal inspection .............................................. . . . 75 And vehicles warning .............................................. . 121
Reverse signal inspection ....................................... . . . 75 - CAN Communication signal List ...................................... . 122
- Failure diagnosis screen does not start ......................... . . . 76 · Component mounting position ....................................... . 128
- Not at all out of the screen (navigation, TV , Video screen System FIG. .................................................. . 128
except for) .................................................. ..... . . . 79 Antenna configuration diagram ........................................... . 129
- DVD Not out video footage .............................. 81 ·circuit diagram .................................................. ....... . 130
- TV Not out video ......................................... . . . 81 - Notes on input and output signal reference value measurement ........... 132
- TV It reflected the poor or of TV Flowing video ...... . . . 83 - NAVI Control unit input and output signal reference
- RGB Not out screen ...................................... . . . 85 value .................................................. .............. . 132
- RGB Flowing screen ...................................... . . . 87 And video distributor input and output signal reference value ..................... . 136
- RGB It is funny shade of the screen .................... . . . 88 Front display unit input and output standards
Centralized switch ( NAVI Navi operation on the switch) value .................................................. .............. . 144
Can not .................................................. . . . 90 Rear display unit input and output signal reference
- Can not navigate operation by voice ................. . . . 90 value .................................................. .............. . 146
Voice commands even if you press the switch - TV Tuner input and output signal reference value ............... . 148
VOICE MENU There does not appear .................. . . . 92 - BCM Input and output signal reference value .............................. . 151
Guide voice does not come out ................................... . . . 92 - How to proceed with fault diagnosis ....................................... . 153
- DVD Not out video voice .............................. 94 · Self-diagnosis function by self-diagnosis menu ........ 153
Front display does not auto-dimming ... . . . 95 - Fault diagnosis function .............................................. . 154
- The vehicle is stopped at the time of TV Or running but not bitterness Film • Self-diagnostic mode ........................................... . 155
But TV Reflected is ........................................... . . . 96 - NAVI Control unit map DVD -
- TV Voice does not come out from all seats speaker ........ . . . 97 ROM When it is determined that is not inserted ...................... . 157
- TV Do not out sound only from the front speakers Front display unit diagnosis is not real
There .................................................. .............. . . . 98 When facilities .................................................. ... . 157
- TV Voice does not come out only from the rear speakers .... 98 Rear display unit diagnosis has not yet been implemented
And fuel consumption information is not out (traveling even average fuel consumption 及 When .................................................. ............ 159
Display of fine cruising distance is " ** " become) .. . . . 99 - NAVI Control unit has been inserted
Drive information is not accurate, maintenance That map DVD - ROM Or map when it is determined that the is
Information is not accurate ....................................... . 100 abnormal DVD - ROM When you do not put to read the data from ..............................................
- Warning screen does not appear (excluding the charge warning display) .. 102 . 160
System does not start ................................ . 103 - NAVI Control unit and GPS Ante
- Before the state is not stored ............................ . 104 When the connection of Na is abnormal ................................ . 161
• The current position mark is shifted ............................ . 104 Error history mode ....................................... . 161
• The current position mark is forward / Not backward ........... . 105 ·Confirmation - Adjustment mode ........................................ . 164
And direction of the current position mark is mad ..................... . 105 And audio guide confirmation ........................................... . 166
- GPS It does not receive the radio waves from satellites ............. . 106 - NAVI Control unit of the power supply and the earth
And running test .................................................. . 106 Scan circuit inspection .................................................. . 167
- Abnormal and there is no phenomenon example ................................... . 107 And video distributor of power supply and ground circuit inspection ........ 168
Program loading ............................ . 114 • The power of the front display unit and
- NAVI Remove the control unit, taking Ground circuit inspection ........................................... . 169
Bill .................................................. ........... . 115 Rear display unit of the power supply and the earth
- GPS Remove the antenna, mounting ............. . 115 Scan circuit inspection .................................................. . 170
Centralized switch ( NAVI Removing the switch) - TV Inspection of the tuner power supply and ground circuit .. 171
And, mounting .............................................. . 116 - Vehicle speed signal inspection .............................................. . 172
Front display unit ASSY Acquisition of Parking brake signal inspection ..................... . 173
AV - 2
Reverse signal inspection ....................................... . . 174 Rear display opening / closing of the non-operation remote control
- Failure diagnosis screen does not start ........................ . . 174 Down operation does not work ........................................ 209
Front display only Do not out at all screen Navi operation is all due and rear seat Navi remote control
There (Navi, TV , Except for the video screen) ........... . . 178 It does not work .................................................. ..... 211
It does not appear at all screen only, rear-display ..... 180 Press the rear-seat independent switch and rear seat Navi remote control
Front, rear display both DVD The video Not hear the sound independently be ................... 211 B
Not out .................................................. ..... 182 Press the open / close switch and rear seat Navi remote control
Front display only DVD Out the video Rear display does not open and close even ............ 211
Absent .................................................. .......... . . 182 • In the rear seat Navi remote control to operate the angle switch
Rear display only DVD Not out video .. 182 Does not change the angle of the rear display even .. 213
- Can not navigate operation by voice ................... 213 C
Front, rear display both TV ,video ( DVD Except for the video)
does not appear the video .......... . . 183 • The steering wheel switch to operation
Also VOICE MENU There does not appear ............... 213
Front display only TV , Video
Guide voice does not come out ..................................... 214
Not out .................................................. ..... 184
- The vehicle is stopped at the time of TV Or running but not bitterness Film
Rear display only TV , Out video footage D
But TV Is reflected (only on the front display) ..................................................
Absent .................................................. .......... . . 185
............ . . 214
Front, rear display both TV ,video ( DVD Except for the video)
And fuel consumption information is not out (traveling even average fuel consumption 及
flowing video .......... . . 186
Display of fine cruising distance is " ** " become) ... 214
Front display only TV , Video
Drive information is not accurate, maintenance E
Flows .................................................. ..... 187
Information is not accurate ...................................... . . 214
Rear display only TV , The video image is flow
- Warning screen does not appear (excluding the charge warning display) ... 214
It is .................................................. .......... . . 188
System does not start ................................. 215
Front, rear display both RGB screen
- Before the state is not stored .............................. 215
Not out .................................................. ..... 189
• The current position mark is shifted .............................. 215 F
Front display only RGB Out screen
• The current position mark does not move forward / backward .......... . . 215
Absent .................................................. .......... . . 190
And direction of the current position mark is mad ...................... 215
Rear display only RGB Not out screen .. 192
- GPS It does not receive the radio waves from satellites .............. 215
Front, rear display both RGB screen
And running test .................................................. . 216
Funny shade of ................................... . . 193 G
- Abnormal and there is no phenomenon example ..................................... 216
Front display only RGB The color of the screen
Program loading .............................. 216
Is funny fit .......................................... . . 196
- NAVI Remove the control unit, taking
Rear display only RGB Tint of the screen
Bill .................................................. ............ 216
Funny is .................................................. . 198
- GPS Remove the antenna, mounting .............. 217 H
Front, rear display both RGB screen
Centralized switch ( NAVI Removing the switch)
Flows .................................................. ..... 200
And, mounting ................................................ 217
Front display only RGB Flow screen
Front display unit ASSY Acquisition of
It is .................................................. .......... . . 201
Disconnect, mounting ...................................... . . 217
Rear display only RGB Flowing screen .. 202 I
Front display unit ASSY Minute of
Video does not appear the video only ............................ . . 203
Solution, assembly .............................................. . . 218
- TV , Video audio Do not out of the seats speaker
Rear display unit ASSY Removing the
There .................................................. ................ 204
And, mounting ................................................ 219
- TV , Video sound from the front speakers
- TV Remove tuner, mounting ............. 220 JA
Not come out only .................................................. . 206
And video distributor of (the rear seat with a voice independent function) taken
- TV , Video sound only from the rear speakers
Disconnect, mounting ...................................... . . 220
Does not appear .................................................. ......... 206
Video removal of jack, mounting ........ 221
Video does not appear sound only ................................. 206
Car Wings & hands-free phone ................. 222
Centralized switch ( NAVI Navi operation on the switch)
System Overview ................................................ 222 AV
Can not .................................................. . 207
· Component mounting position ........................................ 223
Front, rear display both automatic dimming and
System FIG. .................................................. . 223
Absent .................................................. .......... . . 207
·circuit diagram .................................................. ...... . . 224
Do not auto-dimming only front display .. 209
- Notes on input and output signal reference value measurement ............ 225
• Do not auto-dimming rear only display ........ 209 L
AV - 3
- NAVI Control unit input and output signal reference And audio is not transmitted to the other party ............................ . 236
value .................................................. .............. . 225 - TEL Table telephone operation screen even if you press the switch
And video distributor input and output signal reference value ..................... . 227 Not shown .................................................. . 238
- TV Tuner input and output signal reference value ................ . 228 - Outgoing / incoming call can not be ................................. . 239
- BCM Input and output signal reference value .............................. . 229 And information centers and communications can not ............... 241
- How to proceed with fault diagnosis ....................................... . 230 - Voice guidance and text-to-speech is no sound ........ 244
- Fault diagnosis function .............................................. . 231 - Auto DJ Switch / Compass link light scan
·Confirmation - Adjustment mode ........................................ . 231 It does not appear Membership screen even if you press the switch (at the
- NAVI Control unit of the power supply and the earth time of service non-participation) .......................... . 245
Scan circuit inspection .................................................. . 232 - Abnormal and there is no phenomenon example ................................... . 246
- Phenomenon by fault diagnosis ........................................... . 233 And removal of the microphone, mounting ..................... . 248
- Partner of the voice is not heard ............................ . 233 - TEL Removal of the harness, mounting ........... 248
AV - 4
Notes on work
SRS Air bag, care about the pre-tensioner seat belt with a car JKS00CVW
warning : • SRS The configuration of the associated air bag and pretensioner seat belt system components desorption and harness desorption, key
switch OFF In, disconnect the negative battery terminal Three It is carried out after leaving more than minute. (For discharging the electricity stored in the auxiliary power
• The desorption of the components, air tools and power tools, etc. that you do not use. B
• SRS Air bag and harness for the pre-tensioner seat belt system is, that you do not repair by solder or the like. In addition, careful attention should be given to
interference with the biting and other parts of the harness.
• SRS That you do not use the electric tester such as circuit testers when the inspection of the air bag and pretensioner seat belt circuit and
separately state. (Working prevention by fine current of the tester)
C
• The connector of the air bag module and pre-tensioner seat belts, of foreign matter such as a driver plug is not. (Working preventing
electrostatic)
• SRS The airbag and pretensioner seat belt, using the yellow harness connector as identification, and to distinguish from other harness.
D
• For safety reasons, maintenance work, " SB Seat belt "and" SRS SRS Making reference to the air bag. "
JA
AV
AV - 5
audio
• Employing an audio system which enables operation by the steering wheel switch and the rear seat multi remote controller.
• Steering wheel switch operation signal BCM Type in, it is sent to the e-tuner radio.
• Operation signal of the rear-seat multi-remote control is input to the remote control receiver in the overhead console (air conditioning display section), the
body from the roof control unit CAN communication( H line, L By a line) BCM It is output to. BCM
• Car Wings corresponding twin monitor TV / Navigation system ( DVD Rear speaker output of the car with system) is input to the video distributor from an
electronic tuner radio, output from the video distributor to the rear speakers.
• Operation example: AM Three To channel 1467 If you want to preset the kHz
ELI0672D
PKIA1423J
AV - 6
audio
JA
AV
TKWA0502J
AV - 7
audio
SKIA9132J
AV - 8
audio
CD Heck AM / FM Electronic tuner radio input and output signal reference value JKS00A25
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signalKey
+- Operation or state
SW
C
SKIA0177J
D
Two Six Speaker output output ACC
(Front right)
SKIA0177J
Light SW ON E
about 12V
Three Bo Illuminating signal input OFF When (one step)
De
Light SW OFF Time about 0V
I|
Four A| ACC Power supply input ACC - Power-supply voltage
scan
Antenna amplifier ON Signal F
Seven output ACC - about 10V that's all
SKIA0177J
H
Radio broadcast reception during
SKIA0177J
Voice commands ON
(Press state): about 1.7V VOL ( DOWN
26 Control signal B input ACC Steering wheel
SW Each of SW Press ) ON
L
(Press state): about 3.3V
AV - 9
audio
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signalKey
+- Operation or state
SW
Bo
de
I|
Control signal ground
28 A| - ON - about 0V
scan
AM - FM (Main) signal
71 - input - - -
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signalKey
+- Operation or state
SW
SKIA0177J
SKIA0177J
SKIA0177J
SKIA0177J
AV - 10
audio
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signalKey
+- Operation or state
SW
Bo
de
E
I|
Control signal ground
A
twenty two | - ON - about 0V
scan
49 - B / CAN-L - - - - F
Voice commands ON
63 - B / CAN - H - - - -
AV
AV - 11
audio
MD - CD Heck AM / FM Electronic tuner radio input and output signal reference value JKS00A26
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal Key
+- operation
SW
SKIA0177J
SKIA0177J
Light SW ON
about 12V
Three Bo Illuminating signal input OFF When (one step)
A| Antenna amplifier ON
Seven
scan output ACC - about 10V that's all
signal
Amplifier ON signal
Eleven ACC - about 10V that's all
(Super woofer) output
SKIA0177J
SKIA0177J
AV - 12
audio
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal Key
+- operation
SW
CH (UP) ON
(Press state): about 1.7V VOL B
19 Control signal A input ACC Steering wheel
SW Each of SW Press (UP) ON
(Press state): about 3.3V
(DOWN) ON D
(Press state): about 3.3V
AM - FM (Main) signal
71 - input - - -
E
72 - FM (Sub) signal input - - -
* One : Car Wings corresponding (Twin monitor) TV / Navigation system ( DVD Method) attaching car
* Two : X as well as XL Grade of CARWINGS corresponding (Twin monitor) TV / Navigation system ( DVD Method) less car
F
Video distributor input and output signal reference value JKS00CWU
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signalKey
+- Operation or state G
SW
SKIA0177J
JA
SKIA0177J
AV
AV - 13
audio
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signalKey
+- Operation or state
SW
SKIA0177J
SKIA0177J
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signalKey
+- Operation or state
SW
) ON
(Press state): about 3.3V
twenty two
the above SW OFF :about 5V
Bo
de
I|
Control signal ground
A
twenty two | - ON - about 0V
scan
49 - B / CAN-L - - - -
AV - 14
audio
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signalKey
+- Operation or state
SW
) ON
(Press state): about 3.3V
62 the above SW OFF :about 5V C
Bo
de
I| E
Steering wheel
62 A| - ON - about 0V
SW Signal Ground
scan
63 - B / CAN - H - - - - F
* One : Car Wings corresponding (Twin monitor) TV / Navigation system ( DVD Method) attaching car
* Two : X as well as XL Grade of CARWINGS corresponding (Twin monitor) TV / Navigation system ( DVD Method) less car
2. To grasp the system overview. " System Overview "( AV-6 page ) See.
3. Phenomenon that corresponds to the phenomenon by fault diagnosis quick reference table is whether to confirm certain. " Phenomenon by fault diagnosis Chart "( AV-16 page ) See.
H
Four. The power supply circuit inspection of electronic tuner radio as a diagnostic before inspection do. " Inspection of the power supply circuit "( AV-18 page ) See.
Five. It performs a failure diagnosis from each phenomenon, to identify the cause.
I
6. Before you replace the failed components were determined to be defective in the diagnosis, make a connection confirmation of the connector again.
8. Or failure of the system to operate properly? In the case of normal Nine What. If abnormalities Five What.
JA
9. Exit.
AV
AV - 15
audio
error indication
• Remove the battery terminal, the broadcasting station of memory has been the radio it is all clear to return to the initial state.
• CD Heck AM / FM Electronic tuner radio ( PY430 ) May error code below is displayed on the display unit. If you see, make the treatment of the
following.
• Failure phenomenon of audio, external factors ( CD , MD Since the failure and interference, etc.) or in many cases to operate due to the imperfect, to carry out fault diagnosis from and inspect the
CD , MD It occurs in all
• BAS , TRE Adjustment is made in the center Dolphins • Electronic tuner radio
Sound bad
• speaker
CD Only occurs
• Already CD Or it does not contain a Electronic tuner radio, electronic tuner radio power circuit
CD There can not be inserted
adhesion of water
Electronic tuner radio
• Dirt on the disc, scratches, or there is no
adhesion of water
Sound flies, interrupted, broken
• Or not due to intense vibration
AV - 16
audio
MD Only occurs
adhesion of water
You can not play B
• Nothing has been recorded on the disc
adhesion of water
Sound flies, interrupted, broken
• Or not due to intense vibration
C
note One : Cause the receiving sensitivity of the glass antenna is reduced. note Two : Fading noise, a foreign noise noise, by train or by the electric field fluctuations, such G
• Fading Noise: Radio waves are blocked, such as in the mountains and buildings, noise generated in order to vary the strength of radio waves in a narrow range.
• Multipath noise: Noise that radio waves were sent directly from the radio waves and broadcasting station which has been reflected, such as mountains and buildings caused by Re figure of time
H
until it reaches the antenna.
Due to the failure of the noise prevention parts or electrical equipment, sometimes the car itself becomes the noise sources. Engine rotation, key switch position, check the occurrence and
changes in noise due to the operation of each of the electrical components, to measure the defect site. Reference: While listening to the noise of each of the electrical components of the fuse One
I
As you remove each individual, you can find the source of the noise easily.
JA
Generation status The main defect site
speed of sound in accordance with the rotation of the • Ignition capacitor failure
engine.
engine ON Only occurs when Or whir will occur when the high engine AV
rotation, when the engine rotation, light ON Sometimes
• Alternator failure
the sound of Jean occurs.
It occurs in conjunction with the operation of the fuel pump. • Fuel pump condenser failure
L
AV - 17
audio
Generated at the time of various motor actuation. • Ground failure of the motor case
• Motor failure
Running, crackling sound is generated when particularly intense vibration. • Ground failure due to mounting of parts failure
• Poor contact or short-circuit of wiring
1. Fuse inspection
Or to check there is no blow to the following fuse of electronic tuner radio.
OK » Two What
NG »If the fuse had blown, replace from to repair the cause of the blow to the new fuse.
Connector of the electronic tuner radio ( NS Type Ten Remove the pole), the terminal number of the
vehicle-side harness connector of the table below (+), the body earth (- measured as).
SKIA3032J
OK »Normal
NG »To repair the power supply circuit harness of electronic tuner radio.
AV - 18
audio
Electronic tuner radio does not operate with a steering wheel switch operation JKS00B5N
NO » Two What
Disconnection to harness between the spiral cable - steering wheel switch or visual inspection no.
OK » Three What D
NG »To repair the spiral cable - steering wheel switch between the harness
Le cable vehicle side harness connector 32 , twenty four , 31 To check the conduction between the turn
terminal.
F
62 ~ 31 : Yes conduction
G
3. BCM Vehicle side harness connector Fifty , 61 , 62 Ban terminal ~ Body
JA
AV
AV - 19
audio
2. BCM Vehicle side harness connector Two , twenty one , twenty two Ban terminal ~ e-Chu
Narajio vehicle side harness connector 26 , 19 , 28 To check the conduction between the turn terminal.
3. BCM Vehicle side harness connector Two , twenty one , twenty two Ban terminal ~ Body
OK » Five What
connector twenty one , Two Ban terminal ~ twenty two To check the voltage between the turn terminal.
Measuring terminal
Measurement condition Reference value
(+) (-)
twenty two
ON - OFF ON (Pressed) about 0V
AV - 20
audio
Audio operation by the rear seat remote control does not work JKS00C14
2. Other than audio (air conditioning, room lamp) to check the operation carried out the operation of the remote controller.
NO » Two What
2. Verification and inspection of the remote control body and the light-receiving part C
• Or the remote control are working toward the light-receiving unit (in the overhead console)
• Seal and dirt on the remote control light-receiving unit, and the like, or not get in the way of the signal is not attached D
• It is not the life of the remote control battery
• Remove the seal and dirt that could be interfering with the signal
BCM Perform self-diagnosis (communication diagnosis). " BCS Body Control System " " Communications Diagnostics " (BCS-34 page ) See.
YES » " Failure code 52 "( BCS-67 page ) Perform an inspection to check, check again phenomenon. G
JA
AV
AV - 21
audio
1. Harness inspection
1. Electronic tuner radio ( NS Type Ten Pole) and sound misses the side connector of the front speakers that do not sound.
connector (+), (-) to check the continuity between the terminals and between the body earth.
Harness connector Two , Six Ban terminal ~ front speakers (right) car both sides harness
connector (+), (-) to check the continuity between the terminals and between the body earth.
SKIA2754J
Inspection results OK Or?
OK » Two What
NG »To repair the electronic tuner radio-front speakers between the harness
2. The key switch ACC To, an electronic tuner radio power ON To.
Four. If the right-hand speaker is abnormal, electronic tuner radio vehicle side
Harness connector Two ~ Six To check the voltage waveform between the turn terminal.
Measuring terminal
Measurement condition Reference value
(+) (-)
One Five
SKIA0177J
SKIA2872J
AV - 22
audio
No sound only from the rear speakers (car Wings corresponding TV / Navigation system ( DVD Method) attaching car
only) JKS00C2G
1. Harness inspection
1. Electronic tuner radio ( NS Type Six Pole) and sound misses the connector on the side of the rear speakers do not sound.
B
2. If the right-hand speaker is abnormal, electronic tuner radio vehicle side hard
Ness connector Twelve , Sixteen Ban terminal - rear speakers (right) vehicle side harness connector
(+), (-) to check the continuity between the terminals and between the body earth.
C
Twelve - (+) : Yes conduction
D
3. If the left speaker is abnormal, electronic tuner radio vehicle side hard
Ness connector 14 , Fifteen Ban terminal ~ front speakers (left) the vehicle side harness
connector (-), to check the continuity between and between the body earth (+) terminal.
E
14 - (-) : Yes conduction
SKIA2762J
Inspection results OK Or?
OK » Two What
NG »To repair the electronic tuner radio - rear speakers between the harness
G
JA
AV
AV - 23
audio
1. To connect the connector of the electronic tuner radio and rear speakers.
2. The key switch ACC Then, the power of the electronic tuner radio ON To.
3. If the right-hand speaker is abnormal, electronic tuner radio vehicle side hard
Ness connector Twelve Ban terminal ~ Sixteen To check the voltage waveform between the turn terminal.
Four. If the left speaker is abnormal, electronic tuner radio vehicle side hard
Ness connector Fifteen Ban terminal ~ 14 To check the voltage waveform between the turn terminal.
Measuring terminal
Measurement condition Reference value
(+) (-)
Twelve Sixteen
SKIA0177J
SKIA2873J
No sound only from the rear speakers (CARWINGS corresponding twin monitor TV / Navigation system ( DVD Method)
attaching car only) JKS00C2D
1. Video distributor ( NS Type Eight Pole) and electronic tuner radio ( NS Type Six Remove the connector of the pole).
2. If the left speaker is abnormal, the video distributor vehicle side Hanesukoneku
Tar 65 , 66 Ban terminal ~ electronic tuner radio vehicle side harness connector Fifteen , 14 To check the
66 ~ 14 : Yes conduction
3. If the right-hand speaker is abnormal, the video distributor vehicle side Hanesukoneku SKIA2758J
Tar 67 , 68 Ban terminal ~ electronic tuner radio vehicle side harness connector Twelve , Sixteen To check the
OK » Two What
NG »To repair the harness between the video distributor - electronic tuner radio
AV - 24
audio
2. The key switch ACC To, the electronic tuner radio ON To.
3. If the left speaker is abnormal, the video distributor vehicle side Hanesukoneku
Tar 65 Ban terminal ~ 66 To check the voltage waveform between the turn terminal.
B
Four. If the right-hand speaker is abnormal, the video distributor vehicle side Hanesukoneku
Tar 67 Ban terminal ~ 68 To check the voltage waveform between the turn terminal.
Measuring terminal
Measurement condition Reference value
(+) (-) C
65 66
SKIA0177J
OK » Three What
SKIA2874J
3. Harness inspection 2
3. If the left speaker is abnormal, the video distributor vehicle side Hanesukoneku
Tar 61 , 62 Ban terminal - rear speakers (left) the vehicle side harness connector (+), (-) you check
the continuity between the terminals and between the body earth.
Four. If the right-hand speaker is abnormal, the video distributor vehicle side Hanesukoneku
Tar 63 , 64 Ban terminal - rear speakers (right) vehicle side harness connector (+), (-) you check
the continuity between the terminals and between the body earth.
JA
SKIA2875J
Inspection results OK Or?
OK » Four What
L
NG »Repair the video distributor - rear speakers between the harness
AV - 25
audio
2. The key switch ACC Then, the power of the electronic tuner radio ON To.
3. If the left speaker is abnormal, the video distributor vehicle side Hanesukoneku
Tar 61 Ban terminal ~ 62 To check the voltage waveform between the turn terminal.
Four. If the right-hand speaker is abnormal, the video distributor vehicle side Hanesukoneku
Tar 63 Ban terminal ~ 64 To check the voltage waveform between the turn terminal.
Measuring terminal
Measurement condition Reference value
(+) (-)
61 62
SKIA0177J
SKIA2876J
AV - 26
audio
Removal of the electronic tuner radio, mounting ( CD Heck AM / FM Electronic tuner radio)
JKS00A2C
removal
1. Cluster lid C A remove. " IP Instrument panel "of "Removing, mounting" ( IP-5 page ) reference
2. Cluster lid C The rear surface of the mounting screw ( Three Remove the book), electronic
B
Remove the tuner radio.
PKIA1270J
3. Remove the electronic tuner radio fixed screw and installation pocket fixing screw, remove the bracket (left and right)
It is.
PKIA1271J
attachment
Mounting attention to the following points, carried out in the reverse order of removal.
JA
Caution : Since the mounting screw of the electronic tuner radio and installation pocket is different, it does not make a mistake mounting.
AV
AV - 27
audio
Removal of the electronic tuner radio, mounting ( CD - MD Heck AM / FM Electronic tuner radio)
JKS00A2D
removal
PKIA1272J
1. Cluster lid C A remove. " IP Instrument panel "of "Removing, mounting" ( IP-5 page ) reference
PKIA1273J
Four. Cluster lid C The rear surface of the mounting screw ( Three Remove the book), electronic
PKIA1274J
AV - 28
audio
Five. Mounting screw ( Four Remove the book), control panel ASSY It is taken up
remove.
PKIA1276J
Caution : • When the electronic tuner radio body carry, or cassette insertion slot
• CD And care must be taken to foreign matter is not mixed into the cassette insertion slot.
PKIA1275J E
attachment
Installation is carried out in the reverse order of removal.
removal
1. Remove the front door finisher. " EI Exterior and interior "of "Front door trim" ( EI-26 page ) See.
PKIA1278J I
attachment
Installation is carried out in the reverse order of removal.
JA
AV
AV - 29
audio
Removal of the slide door speakers, mounting ( Four Door car, Five Car door) JKS00B1A
removal
1. Remove the slide door finisher. " EI Exterior and interior "of " Slide door finisher " (EI-27 page ) See.
2. Speaker mounting screw ( Four Remove the book), speaker and harness
PKIA1279J
attachment
Installation is carried out in the reverse order of removal.
Removing the rear side speakers, mounting ( Four Car door) JKS00B1B
removal
1. Remove the rear side finisher lower right. " EI Exterior and interior "of "Rear side finisher lower" ( EI-30 Page
Di ) See.
2. Speaker mounting screw ( Four Remove the book), speaker and harness
PKIA1280J
attachment
Installation is carried out in the reverse order of removal.
removal
1. Remove the front pillar garnish. " EI Exterior and interior "of " Front pillar garnish " (EI-29 page ) See.
2. Front pillar garnish the rear surface of the mounting screw ( Two Remove the book),
PKIA1281J
AV - 30
audio
attachment
Installation is carried out in the reverse order of removal.
removal
1. Remove the personal lamp assembly. " EI Exterior and interior "of "Removing, mounting" ( EI-36 page ) See. B
2. Personal lamp assembly the back side of the mounting screw ( Two A book)
PKIA1282J
attachment
Installation is carried out in the reverse order of removal.
E
removal
F
1. Remove the rear side finisher lower right. " EI Exterior and interior "of "Rear side finisher lower" ( EI-30 Page
Di ) See.
Four. Mounting screw ( Three Remove the book), remove the super woofer.
PKIA1283J
removal I
" SRS SRS Air bag "of "Removing, mounting" ( SRS-17 page ) See. JA
AV
AV - 31
antenna
audio
PKIA1284J
SKIA2498J
AV - 32
antenna
removal
1. Remove the rear side Huy nickel Shah upper right. " EI Exterior and interior "of " Rear side finisher Upper " (EI-
31 page ) See.
2. Remove the head lining. " EI Exterior and interior "of "Removing, mounting" ( EI-36 page ) See.
B
3. Mounting bolts ( One Remove the book), remove the radio antenna amplifier.
D
PKIA1285J
attachment
Installation is carried out in the reverse order of removal.
E
JA
AV
AV - 33
Car Wings correspondence TV / Navigation system ( DVD method)
The navigation system, the moving distance of the vehicle obtained from the vehicle speed sensor, turning angle of the
vehicle obtained from a gyro (angular velocity sensor) and GPS Antenna ( GPS The traveling direction of the vehicle
obtained from information) Three To calculate the current position at a certain period from the type of signal. This and
the calculated current position DVD-ROM Map that contains the drive
DVD-ROM It specifies the current position by comparing the map data read from the
(map matching), and displays the current position mark on the display.
EL-2956D
It should be noted that, GPS Comparing the position detection result by the position detection result and map matching
of the vehicle obtained from, using the location data accuracy is determined to be. At the time of calculating the current
position to detect the moving distance and traveling direction of change between the from the previous calculation point
EL-0469D
Moving distance
Moving distance of the vehicle is calculated by an input signal from the vehicle speed sensor. Thus, due to wear of the tire, since the correct distance reduces that it will not be
Direction of travel
Change of course of the vehicle, a gyro (angular velocity sensor) and GPS antenna( GPS Calculated by information). this Two One to have each of the advantages and disadvantages, this
depending on the situation Two While prioritize the Tsukara of the signal, this according to the more accurate traveling direction status Two Changing the priority of Tsukara the signal to detect
Gyro (angular velocity sensor) • The turning angle can be very accurately detected. • Errors are accumulated for a long time continuous running.
• When the vehicle speed is slow it can not detect the correct
GPS antenna( GPS information) • Direction in which the progress of the vehicle (north, south, east and west)
It can be detected. orientation.
Map-matching
The map matching, the calculated current position by the method described by the position detection principle DVD-ROM
Map stored in the drive DVD-ROM Compared to the surrounding road map data elaborate read from Note, a
function for correcting the current position on the most accurate and was estimated road. Therefore, in the
case of the following, GPS When information is received difficult situation, because there may not be corrected
properly after Barack traveling, there is a need to modify the current position mark manually.
Caution : Road map data map DVD-ROM And the data in the based on
There.
ELK0097D
AV - 34
Car Wings correspondence TV / Navigation system ( DVD method)
• The map matching, in addition to roads and position correction is determined that the vehicle is currently
Therefore, if the distance or azimuth has an error, the error priority of roads that are
candidates also occurs that the position fix to the wrong road. Also, in places like roads are
run in parallel, the priority about the same next to both roads, and the like delicate steering
and road shape, the current position mark is displayed alternately on both road there is.
EL-0470D
• In such as traveling to that road is new, map DVD-ROM If you have not been recorded, the C
map matching is not possible to. Also it can not be performed correctly map matching may
Therefore, when traveling on the road is not on the map, and map matching to another road that are
D
not currently running, there is that the current position mark would have been displayed on the road.
Thereafter, when the road is actually traveling could detect is sometimes jump the current position
• Distance and position and the traveling direction calculated by the orientation map DVD-ROM Because the range is limited to be able to compare the
pressurized et al read road data, if the degree more than the current position is shifted Ru Oh, it can not be modified in the correct position in the
EL-0471D E
map matching.
GPS The receiver, Four One or more of the GPS Ri by the time difference between the radio waves arriving from the
satellite, of the vehicle Three Position dimension (latitude, longitude, altitude) is calculated. ( Three Dimension
G
measurement position) GPS Radio waves from a satellite Three Only when you can not receive One is Four Horn GPS
Using the altitude data when determined using the satellite Two To calculate the position of dimensions (latitude,
longitude). ( Two Dimension positioning) the following cases GPS Accuracy is poor.
ELK0098D
H
• Two In the dimension positioning, accuracy is degraded when the altitude of the vehicle position changes.
• Position detection performance, high accuracy Three Even in dimension positioning 10m There is a degree of error. Further, accuracy is utilized for positioning GPS Due to the influence of the
placement of the satellite, GPS Depending on the arrangement of the satellite position detection performance is reduced.
• In the tunnel, parking in the building, such as under the elevated highway, GPS If the radio waves from the satellite can not be received, it can not position detection. Also, GPS When you place an
I
object on top of the antenna of use, GPS It may be radio wave from a satellite can not be received.
JA
AV
AV - 35
Car Wings correspondence TV / Navigation system ( DVD method)
• NAVI When the control unit exchange, map before you remove the battery DVD-ROM It is taken out.
• NAVI Because the following items are memory to the control unit, at the time of unit exchange ahead of the memory contents, to re-enter if necessary.
• Dimming switch
[ Navi mode relationship] • The previous display last state (the map screen / Bird view, scale, of the map screen rotation state, of Rutoga Ido ON / OFF , The
trajectory ON / OFF etc)
• present location
System summary
• Combination meter (meter control unit ASSY A warning signal from the) CAN communication( H line, L More in line) BCM But it received, BCM To
display a warning screen by sending to the front display unit from.
• Warning screen ( RGB Image data) are memory inside the front display unit, BCM To interrupt displays a warning screen to the navigation screen through
the communication with the front Display unit with.
• Warning display displays the name and the address the contents of the vehicle abnormal site on the front display. In addition, the interrupt display-law warning or abnormal is not
resolved.
System chart
PKIA1756J
AV - 36
Car Wings correspondence TV / Navigation system ( DVD method)
SKIA2520J
SKIA2521J F
●: Submit ○: reception
● ○ I
A / T Electronic control system warning signal
○ ●
door SW signal ● ○ ○ ○
○ ●
Oil pressure warning signal
JA
● ○
AV - 37
Car Wings correspondence TV / Navigation system ( DVD method)
● ○
ABS Warning light signal
○ ●
SKIA2522J
SKIA2523J
●: Submit ○: reception
In Terri
Con
Jefferies Con
To Adaptive Laser
cement bi
Low cruise VDC / radar
key Yu Natick Steering
Luba control TCS / sensor nickel To reference
IPDM E /
The main signal name / Connection unit ECCS BCM tion angle
C/U valve systems ABS C / R
meter sensor
ASSY U
- A / TC / C/U
U One
AV - 38
Car Wings correspondence TV / Navigation system ( DVD method)
In Terri
Con
Jefferies Con
To Adaptive Laser
cement bi
Low cruise VDC / radar
key Yu Natick Steering
Luba control TCS / sensor nickel To reference
IPDM E /
The main signal name / Connection unit ECCS BCM tion angle
C/U valve systems ABS C / R
meter sensor
ASSY U
- A / TC / C/U
U One B
) ● ○
● ○
A / T Electronic control system warning signal
○ ●
C
door SW signal ● ○ ○ ○
○ ●
Oil pressure warning signal
● ○
● ○
ABS Warning light signal
○ ● I
Reference :( One ) Intelligent Key unit attaching car only vehicle speed signal ( VDC
JA
AV
AV - 39
Car Wings correspondence TV / Navigation system ( DVD method)
SKIA2524J
SKIA2525J
●: Submit ○: reception
ABS
Control
Aku Ju Intelligent Combi
Transformer valve
er ter Kiyuni' To reference Nesho IPDM E /
The main signal name / Connection unit ECCS fur BCM One
C/U Nme ter R
C/U ASSY -
A / TC / U
C/U
● ○
A / T Electronic control system warning signal
○ ●
door SW signal ● ○ ○ ○
○ ●
Oil pressure warning signal
● ○
AV - 40
Car Wings correspondence TV / Navigation system ( DVD method)
ABS
Control
Aku Ju Intelligent Combi
Transformer valve
er ter Kiyuni' To reference Nesho IPDM E /
The main signal name / Connection unit ECCS fur BCM One
C/U Nme ter R
C/U ASSY -
A / TC / U
C/U
● ○
ABS Warning light signal
○ ●
SKIA2526J
SKIA2527J
●: Submit ○: reception JA
Con In Terri
To Jefferies Con
Adaptive Laser
Transformer Low cement bi
cruise VDC / radar
ECC file over C Luba key Yu Natick Steering
control TCS / sensor IPDM E /
The main signal name / Connection unit SC / /U valve BCM nickel tion angle AV
systems ABS C / R
U ASS To Reference meter sensor
U
Y- One
C/U
A / TC
/U
AV - 41
Car Wings correspondence TV / Navigation system ( DVD method)
Con In Terri
To Jefferies Con
Adaptive Laser
Transformer Low cement bi
cruise VDC / radar
ECC file over C Luba key Yu Natick Steering
control TCS / sensor IPDM E /
The main signal name / Connection unit SC / /U valve BCM nickel tion angle
systems ABS C / R
U ASS To Reference meter sensor
U
Y- One
C/U
A / TC
/U
signal ○ ●
● ○
A / T Electronic control system warning signal
○ ●
door SW signal ● ○ ○ ○
○ ●
Oil pressure warning signal
● ○
● ○
ABS Warning light signal
○ ●
Reference :( One ) Car with intelligent key unit only engine warning
AV - 42
Car Wings correspondence TV / Navigation system ( DVD method)
PKIA1424J F
JA
AV
SKIA2801J
AV - 43
Car Wings correspondence TV / Navigation system ( DVD method)
Antenna path
" Antenna path "( AV-32 page ) reference
AV - 44
Car Wings correspondence TV / Navigation system ( DVD method)
JA
AV
TKWA0504J
AV - 45
Car Wings correspondence TV / Navigation system ( DVD method)
TKWA0505J
AV - 46
Car Wings correspondence TV / Navigation system ( DVD method)
Key switch ACC Or long baseline measurement in the engine stopped state, since this may result in battery depletion, be performed by starting the as possible
engine.
NAVI Control unit input and output signal reference value JKS00BCL
Terminal
Measurement condition B
number Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
Bo
Six Vehicle speed signal ( Two pulse) input ON Vehicle speed about 40km / h Time
de
I|
A|
scan ELF1080D
F
Seven ACC Power supply input ACC - Power-supply voltage
(one step)
Eight Automatic dimming signal input ON G
Light SW ON When it does not shed light
on auto light the light-receiving sensors about 12V
(one step)
JA
SKIA2553J
Concentration SW ( NAVI SW Pressing the)
13
Neu Zureka
AV
Sixteen Communication signal (+) Input and output ON
SKIA2553J
AV - 47
Car Wings correspondence TV / Navigation system ( DVD method)
Terminal
Measurement condition
number Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
Bo
de
I|
A
twenty one | shield( TV ) - ON - about 0V
scan
SKIA0187J
SKIA0186J
SKIA0187J
Bo
de
I|
26 A| shield( TV / DVD ) - ON - about 0V
scan
SKIA0186J
Bo
de
I|
29 A| RGB Signal Ground - ON - about 0V
scan
AV - 48
Car Wings correspondence TV / Navigation system ( DVD method)
Terminal
Measurement condition
number Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
Bo
de
I| B
Thirty A| RGB Synchronization signal output ON
scan
SKIA0164J
SKIA0166J
29
SKIA0167J
F
Bo
de
I|
33 A| RGB Area signal output ON TV SW Press
scan G
SKIA0162J
34 29 RGB Signal ( R :Red ) output ON Screen adjustment of the check and adjustment function
And in the color bar display
SKIA0165J I
A| TV SW Press
scan
AV
L
SKIA0163J
AV - 49
Car Wings correspondence TV / Navigation system ( DVD method)
Terminal
Measurement condition
number Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
SKIA0171J
SKIA0177J
SKIA0177J
SKIA0177J
SKIA2557J
AV - 50
Car Wings correspondence TV / Navigation system ( DVD method)
Terminal
Measurement condition
number Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
B
48 43 TV Audio signal (right +) input ON TV During the broadcast reception
SKIA0177J
C
Bo
de
I|
49 A| Shield (microphone) - ON - about 0V
scan
D
88 89 FM Multiple signal - - - -
Bo
E
de
I|
89 A| Shield (antenna) - ON - about 0V
scan
Bo
de
I|
G
91 A| shield( GPS ) - ON - about 0V
scan
JA
AV
AV - 51
Car Wings correspondence TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
SKIA0165J
SKIA0166J
SKIA0167J
Bo
de
I|
Four A| RGB Signal Ground - ON - about 0V
scan
Bo
13 de Communication signal ( BCM - DP ) Input ON
I|
A|
scan
SKIA2559J
information SW Press
SKIA2566J
AV - 52
Car Wings correspondence TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
B
Sixteen Vertical synchronization signal input ON
SKIA0161J
C
Bo
de
I|
17 A| Horizontal synchronization signal input ON TV SW Press
scan
D
SKIA0163J
SKIA0162J
F
SKIA0186J
SKIA0187J I
Bo
de
I| JA
A
twenty four | RGB Synchronization signal input ON Screen diagnosis of check and adjustment function
And in the color bar display
scan
SKIA0164J
AV
Reference: Five , twenty two , twenty three Turn pin function at the time of the back-view camera connection. " DI Driver Information System
AV - 53
Car Wings correspondence TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
Bo
de
I| SKIA2553J
Concentration SW ( NAVI SW Pressing the)
A|
Neu Zureka
scan
SKIA2553J
SKIA0186J
SKIA0177J
Twenty
SKIA0177J
SKIA2553J
AV - 54
Car Wings correspondence TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
Bo
de
B
14 I| Communication signal (-) Input and output ON Concentration SW ( NAVI SW ) Neu
A| Pressing the Zureka
scan
SKIA2553J
C
Sixteen shield( TV ) - ON - about 0V
SKIA0187J
F
SKIA0177J
Bo
de
I|
Twenty A| shield( TV voice) - ON - about 0V G
scan
SKIA0177J
I
twenty four
De Earth - ON - about 0V
Reference: twenty five , 26 , 27 , 28 , 29 , Thirty Turn pin function at the time of dealer options of video jack connection AV
AV - 55
Car Wings correspondence TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- operation
SW
TEL ON
(Press state): about 0V
Voice commands ON
2 22 Control signal B output ON TEL , Voice command, (Press state): about 1.7V VOL ( DOWN
VOL ( DOWN )Press
) ON
(Press state): about 3.3V
(one step)
14 Automatic dimming signal output ON
Light SW ON When it does not shed light
on auto light the light-receiving sensors about 12V
(one step)
Bo
de
Fifteen I| Communication signal ( SW - BCM ) Input ON Concentration SW ( NAVI switch)
Pressing any of the
A|
scan
SKIA2946J
SKIA2559J
SKIA2553J
MODE ON
(Press state): about 0V
CH ( UP ) ON
21 22 Control signal A output ON MODE , CH ( UP ), VOL (Press state): about 1.7V VOL ( UP
( UP )Press
) ON
(Press state): about 3.3V
Bo
de
I|
A
twenty two | Control signal ground - ON - about 0V
scan
AV - 56
Car Wings correspondence TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- operation
SW
B
35 Communication signal ( BCM - SW ) Output ON Concentration SW ( NAVI SW ) Neu
Pressing the Zureka
Bo
de
I| SKIA2947J
A|
C
scan
SKIA2566J
SKIA2553J
F
Bo
de
I|
Forty A| Shield (communication) - ON - about 0V
scan
G
TEL ON
(Press state): about 0V
Voice commands ON H
Steering wheel (Press state): about 1.7V VOL ( DOWN
Fifty input ON TEL , Voice command,
SW signal B VOL ( DOWN )Press
) ON
(Press state): about 3.3V
CH ( UP ) ON
Steering wheel (Press state): about 1.7V VOL ( UP
61 input ON MODE , CH ( UP ), VOL
SW signal A ( UP )Press
) ON JA
(Press state): about 3.3V
Bo
de
I| AV
Steering wheel
62 A| - ON - about 0V
SW Signal Ground
scan
L
Reference: Eighteen , 39 , 70 Ban terminal dealer option of beacon unit, ETC Function at the time of unit connection
AV - 57
Car Wings correspondence TV / Navigation system ( DVD method)
2. To grasp the system overview. " System Overview "( AV-34 page ) See.
3. Not unusual phenomenon example "There is no abnormal phenomenon Example" ( AV-107 page ) A phenomenon that corresponds to confirm it is in.
Four. Carry out the power supply and ground circuit inspection of the relevant unit as a diagnostic before inspection. " NAVI Power supply and the ground control unit
Circuit inspection "( AV-70 page ) , " Power supply and ground circuit inspection of the front display unit "( AV-71 page ) , " TV
Inspection of the tuner power supply and ground circuit "( AV-72 page ) See.
Five. It performs a failure diagnosis from each phenomenon, to identify the cause.
6. Before you replace the failed components were determined to be defective in the diagnosis, make a connection confirmation of the connector again.
8. Or failure of the system to operate properly? In the case of normal Nine What. If abnormalities Five What.
9. Exit.
Overview
• A self-diagnostic mode (excluding the back view monitor) for self-diagnosis function to independently activated from each system, the self-diagnosis menu which can
perform self-diagnosis together several system Two There is a kind.
• Self-diagnosis menu is possible to display the screen switch of each system to the front display, it can be called a self-diagnostic mode you need at the
touch of a button.
Operation procedure
starting method
Five. Air conditioning OFF Press the switch, to stop the air conditioning.
6. While holding down the information switch, temperature control dial (right) Ten Within seconds
SKIA2767J
To Thirty Click to manipulate or more. Reference: The direction of rotation of the temperature control dial (right)
How to undo
AV - 58
Car Wings correspondence TV / Navigation system ( DVD method)
Menu item
The communication diagnosis by transmission and reception of data on the network do. Detail is "Communication Diagnostics "
system
(BCS-34 page ) See.
Air conditioning Perform self-diagnosis of air conditioning. Detail is "Self-diagnosis function" ( ATC-19 page ) See.
A change in the state of each switch is detected by the data on the network. Detail is "Switch Monitor" ( BCS-39 B
switch
page ) See.
• Color bar color shade confirmation of by the color of the confirmation and gray scale display by the display.
monitor
• It is back view video display car width and distance of the guide line correction of the time. Detail is "Self-diagnosis
menu" ( DI-44 page ) See.
C
• Lighting of the auto light, can adjust the sensitivity of the off.
Vehicle setting
• To set the timer operating time of the rear defogger.
NAVI Perform self-diagnosis of navigation. Detail is "Fault diagnosis function" ( AV-59 page ) See.
D
Fault diagnosis function JKS00BCO
Overview
• Fault diagnosis function, it is automatically and self-diagnostic mode that diagnosis is made, check and adjustment mode to operate manually.
• Self-diagnostic mode, the connection confirmation and individual unit diagnosis between the units that this cis-formed collectively carried out, and display the results on the liquid crystal display. E
• Check and adjustment mode, it requires a decision and a human operator (can not be automatic judgment of the system side) fault diagnosis, to display the error history of the check and change
F
Operation procedure
2. "Map / PLAY "Switch and the" image quality "switch at the same time Five Press sec or more.
SKIA2567J
I
3. "Fault diagnosis" screen is displayed.
Four. " self-diagnosis "," Error history "," check and adjustment "and" voice guide confirmation
AV
SKIA2568J
AV - 59
Car Wings correspondence TV / Navigation system ( DVD method)
Diagnostic items
• C / U Diagnosis of (map DVD-ROM Not inserted at the time of DVD-ROM Driver units diagnosis of is not
performed)
self-diagnosis
• C / U ~ GPS Connection diagnosis between the antennas, C / U - Make a diagnosis of the connection diagnostic and
To view the problems and the number of occurrences of occurred in the past was Navi relationship. In addition, to display
Error history
the last time and place that occurred When you select a defect item.
Confirmation of color by color bar display, and Shades of colors by gray scale display can be
Screen Adjustment
confirmed.
Vehicle speed, parking brake, light, IGN (Key SW ), Can each signal diagnosis of the reverse.
Vehicle signal
Navigation adjustment When deviation occurs in the angle angle and car mark angle adjustment wheel bends actually bends
It can be adjusted.
It can be adjusted when the deviation between the actual position and distance adjustment current position mark has occurred.
Check and adjustment Hands-free volume control, communication modem ID Confirmation, memory erasure, Information Center phone
Communication modem settings
number registration, can be confirmed Mike speakers.
DVD-ROM driver, DVD-ROM To display the version of the software and the unit, such as
Version Display
a.
Error history, error history erase, ETC Ru can erase unit of the connection history.
ETC unit
DVD Erase the personal identification number at the time of parental level set in the video playback.
DVD Personal identification number erase
Audio guide confirmation And it outputs the confirmation sound from the audio guide for the speakers.
Operation procedure
• Bar graph of the lower side of the screen in the self-diagnosis in the screen displays the rate of progress of
the diagnosis.
ELK1432D
2. When the self-diagnosis is completed, the display unit connection confirmation screen.
• If the terms of optional accessories it is determined that the abnormal connection, the relevant parts to
display from either confirmation screen is attached to the actual. If you are attached to select the screen
• In the case of optional accessories connection is normal, appropriate screen switch is not displayed.
SKIA2569J
AV - 60
Car Wings correspondence TV / Navigation system ( DVD method)
3. The screen switch of the diagnostic result screen unit name, depending on the diagnosis result
B
Caution : MET & A / C ECU In the text in the BCM It has been referred to as.
• For one unit, screen switch the color of the scene in which a plurality of error has occurred at the same
SKIA2570J
• Control unit and MET & A / C ECU , TV tuner, GPS Between the antenna is connected by a green or yellow depending on the diagnosis.
C
• Between the units other than the above are connected by a green or gray depending on the diagnosis.
Four. Diagnosis result of comments table and choose a screen switch of diagnostic results in the screen
Shown.
D
• In the case of the green comment " Self-diagnosis is normal. Detailed diagnostics and adjustments are not
made to diagnose according to the "check and adjustment" mode and maintenance manual " To display.
• In the case of the yellow comment will be displayed as "connection with the following unit is abnormal.
E
Please diagnosed according to integer Bei procedure specifications".
• In the case of the red comment will be displayed as "XX unit is abnormal".
• In the case of ash comment " DVD-ROM Because it has not yet been inserted, the control unit ELK1435D
of DVD-ROM To display the diagnosis has not been made "of the driver.
F
1. To select the diagnostic corresponding number from the diagnostic results Chart. G
2. Carry out the inspection of each system from diagnosis number table.
H
Diagnostic result Chart
Screen switch
○ Diagnosis Two
Ash
○ Diagnosis Three
○ Diagnosis Four
JA
○ Diagnosis Five
yellow
○ Diagnosis Six
○ ○ Diagnosis Seven
Caution : Representation of the screen switch has been described as following in the sentence. AV
• control unit: NAVI control unit
• Front seat Display: Front display unit
• MET & A / C ECU : BCM
• TV tuner: TV tuner
• GPS antenna: GPS antenna L
AV - 61
Car Wings correspondence TV / Navigation system ( DVD method)
Diagnostic number Comments content and estimated failure system Deal content and reference destination
Diagnosis Two NAVI C / U There map DVD - ROM It is determined that is not inserted (AV-62)
Diagnosis Three Front display unit diagnosis is not yet implemented (AV-62)
" DVD - ROM It is abnormal. Please check the disk. Comments of "is displayed. NAVI C / U There, the map that has
Diagnosis Four been inserted DVD - ROM It was recognized as abnormal. It should be noted that the map DVD - ROM Abnormality, or NAVI (AV-64)
C / U Failure of is considered.
" DVD - ROM Or NAVI Inside DVD - ROM Driver is abnormal. Please maintenance manual therefore diagnosis.
Diagnosis Five Comments of "is displayed. map DVD - ROM Not read the data. It should be noted that the map DVD - ROM Driver (AV-64)
abnormality is considered
Diagnosis Seven GPS Antenna and NAVI C / U It is but abnormal connection (AV-64)
NAVI Control unit map DVD - ROM When it is determined that is not inserted JKS00CMQ
OK » NAVI C / U Failure
When the front display unit diagnosis has not yet been implemented JKS00CMR
OK » Two What
BCM Perform self-diagnosis (communication inspection). " BCS Body Control System " " Communications Diagnostics " (BCS-34 page ) See.
AV - 62
Car Wings correspondence TV / Navigation system ( DVD method)
Spray unit vehicle-side harness connector 13 , Fifteen To check the conduction of turn terminal.
B
C
4. BCM Vehicle side harness connector Sixteen , 37 Ban terminal ~ Body Architect
OK » Four What
3. Press the information switch, BCM Of the vehicle-side harness connector Sixteen , 37
Measuring terminal G
Measurement condition Reference value
(+) (-)
H
Sixteen
SKIA2620J
37
JA
SKIA2566J
NG » • Constant voltage value (about 5V Replace the front display unit if in the vicinity of) the voltage waveform does not appear
• Constant voltage value (about 0V If the voltage waveform does not appear in the vicinity) is BCM To replace the
AV - 63
Car Wings correspondence TV / Navigation system ( DVD method)
NAVI Map the control unit is inserted DVD - ROM Or map when it is determined that the is abnormal DVD - ROM When
you do not read the data from JKS00CMS
OK » Two What
OK » Three What
NAVI Control unit and GPS When the connection of the antenna is abnormal JKS00CMT
OK » Two What
Other normal GPS Replace the antenna to perform the self-diagnosis again.
AV - 64
Car Wings correspondence TV / Navigation system ( DVD method)
Operation procedure
SKIA2568J
ELK1444D
Diagnostic results at the time of the "self-diagnosis", key SW The ON It is judged by whether or not an error has occurred and from the to the end "self-diagnosis". On the other hand, key SW
H
The ON Previous error occurs that, if not occur until the "self-diagnosis", the diagnostic results Ru is determined to be normal. Therefore, the error that occurred in the past can not be
determined in the "Diagnostic" point, it is necessary to make a diagnosis from the "error history".
I
In the error history, but to display the time and place where the error last occurred to note the following.
• NAVI In the control unit of GPS If the substrate is abnormal, it may not be possible to display the correct time of occurrence.
• Generating location, since the error is the current position mark display position when generated, if has been out of the time mark the correct position, it may not be
possible to display the correct position.
JA
• Maximum number of occurrences Fifty Although stored until times, 51 More than once Fifty It is displayed times.
But reproducible failure has occurred, if isolate the cause of the problem have more than one error is displayed is difficult, after having declined to items and times the number and location
(latitude and longitude) (or the error history in erasing), the once key switch OFF From ON In, and failure to verify again error history from to reproduce, to diagnose the center the items that
AV
Probable cause
Error item Failure phenomenon example
Deal content or content of trouble
NAVI C / U Sub for internal communication with the CPU Communication error with
• To implement the self-diagnostic mode • Portrayal of the front and rear display does L
sub CPU Abnormal connection
• In self-diagnosis NAVI C / U It is considered a temporary abnormality due to not appear
interference of strength if there is normal
AV - 65
Car Wings correspondence TV / Navigation system ( DVD method)
Probable cause
Error item Failure phenomenon example
Deal content or content of trouble
• Carry out the inspection of the vehicle speed signal • Can not navigate the position detection performance
Vehicle speed sensor connection error
" Vehicle speed signal inspection "( AV-73 page ) A reference child the (can not move distance detection)
NAVI C / U With the interior of the GPS Communication with the Board error
• Navigation position detection performance is degraded ( GPS Position
GPS disconnected
• To implement the self-diagnostic mode
correction by is not performed)
• In self-diagnosis NAVI C / U It is considered a temporary abnormality due to
• GPS While the state of the reception of gray
interference of strength if there is normal
GPS ROM Abnormality GPS Because it is not possible to correct positioning by, the
GPS Board Clock I C It is abnormal • Ru Kotogaa the correct time can not be displayed
NAVI C / U When GPS Substrate and GPS Contact with the antenna connection
is abnormal
• Navigation position detection performance is degraded ( GPS Position
NAVI C / U With the interior of the DVD - ROM Communication error with the driver
NAVI C / U Internal and DVD VIDEO Communication error with the module
DVD VIDEO
• To implement the self-diagnostic mode • DVD VIDEO There can not be played
Module abnormal
• In self-diagnosis NAVI C / U It is considered a temporary abnormality due to
TV Tuner connection anomaly • TV Failure of the tuner • TV It does not appear in the video
AV - 66
Car Wings correspondence TV / Navigation system ( DVD method)
Probable cause
Error item Failure phenomenon example
Deal content or content of trouble
Operation procedure
2. By selecting each screen switch of check and adjust the screen, call each diagnosis
Fine out, "Back" Become a check and adjust the initial screen and press the switch.
SKIA2568J
SKIA3018J
JA
AV
AV - 67
Car Wings correspondence TV / Navigation system ( DVD method)
Screen Adjustment
SKIA3033J
• RGB In the case of signal failure of the system, color bar display of color is as follows.
• If the shade is funny is, " RGB Tint of the screen is wrong. "( AV-88 page ) See you confirm that you have read.
• It is the actual comparison confirmation of the signal that is recognized by the state and the system side of each
vehicle signal.
SKIA3034J
ON Light SW ON Time Written by the brightness of the outside of the vehicle SW There is if you do not
Light
OFF Light SW OFF Time want to work in (automatic dimming function)
ON Key SW ON Time
IGN -
OFF Key SW ACC Or OFF Time
ON Select lever R Switching of the range at the time the display is about 1.5 Delayed about seconds Kotogaa
AV - 68
Car Wings correspondence TV / Navigation system ( DVD method)
• The vehicle speed is NG In the case of "Vehicle speed signal inspection" ( AV-73 page ) See you confirm that you have read.
• Parking brake NG In the case of "Parking brake signal inspection" ( AV-74 page ) See you confirm that you have read.
• Lights NG In the case of "Front display does not auto-dimming" ( AV-95 page ) See you confirm that you have read.
• IGN But NG In the case of " IGN Signal inspection "( AV-75 page ) See you confirm that you have read.
• Reverse is NG In the case of "Reverse signal inspection" ( AV-75 page ) See you confirm that you have read.
B
Navigation adjustment
Angle adjustment
• It is possible to adjust the output value of the rotation angle detected by the gyro.
ELK1442D
E
Distance adjustment
• Usually, to automatically adjust the distance error due to the variation of wear and air pressure of the tire by the
automatic distance correction function, such as if you are traveling by mounting a tie or a chain, carried out when
ELK1443D
H
item Adjustment and check the contents
Hands-free volume control Adjust the earpiece volume during a hands-free phone calls (large and small standards and) do.
Communication modem ID Confirmation To check the serial number of the communication modem.
Hands-free phone memory to erase the (redial, transmission and call history, speed dial, such as
Memory erasing I
registration number).
Information Center phone number registration To display the phone number of each information center, it is the telephone number registration.
• The voice that was speaking into the microphone can be output from the front speakers (left side).
Confirmation Microphone Speaker • Decision SW When you press, from the front speakers (left) MUTE And outputs the sound. In addition, at that
time an electronic tuner radio " MUTE " Character is displayed.
JA
Version Display
• DVD - ROM driver, DVD - ROM To display the version of the software and the unit, such as a.
ETC unit AV
ETC Error history of the unit, erase the error history, ETC It can erase unit of the connection history.
DVD It is possible to erase the personal identification number at the time of parental level set in the video playback. L
AV - 69
Car Wings correspondence TV / Navigation system ( DVD method)
Operation procedure
2. Select the decision switch (press) S for voice guide the confirmation sound by
SKIA2568J
NAVI Power supply and ground circuit inspection of the control unit JKS00BCV
1. Fuse inspection
NAVI Or to check there is no blow to the following fuse of the control unit.
OK » Two What
NG »If the fuse had blown, replace from to repair the cause of the blow to the new fuse
NAVI control unit( TH Type Twelve Remove the connector of the pole), the terminal number of the
vehicle-side harness connector of the under-mentioned table (+), the body grounding (- measured as).
SKIA2593J
Inspection results OK Or?
OK » Three What
AV - 70
Car Wings correspondence TV / Navigation system ( DVD method)
NAVI Check for continuity between the following vehicle side harness connector ~ Bo Dee
OK »Normal
Power supply and ground circuit inspection of the front display unit JKS00BCW
1. Fuse inspection D
Blow below the fuse of the front display unit is to check whether or not there.
OK » Two What
F
NG »If the fuse had blown, replace from to repair the cause of the blow to the new fuse
Remove the connector of the front display unit, the terminal number of the vehicle-side
harness connector of the table below (+), the body earth - is measured as ().
H
Terminal number Signal name Key SW Reference value
JA
AV
AV - 71
Car Wings correspondence TV / Navigation system ( DVD method)
Check for continuity between the following vehicle side harness connector - body earth
of the front display unit.
OK »Normal
1. Fuse inspection
TV Blow below the fuse of the tuner is to check whether or not there.
OK » Two What
NG »If the fuse had blown, replace from to repair the cause of the blow to the new fuse
TV tuner( TK Type twenty four Remove the connector of the pole), the terminal number of the vehicle-side
harness connector of the table below (+), the body earth (- to measure) and to.
SKIA2597J
OK » Three What
AV - 72
Car Wings correspondence TV / Navigation system ( DVD method)
TV Check for continuity between the following vehicle side harness connector - body earth of the
tuner.
OK »Normal
Allowed to run the car, carry out the inspection of the speedometer.
2. Harness inspection
F
2. NAVI control unit( TH Type Twelve Remove the connector of the pole) and combination meter.
end child.
H
4. NAVI Control unit vehicle-side harness connector Six Ban terminal
SKIA2600J
OK » Three What
NG » NAVI To repair the harness between the control unit - Combination meter
JA
AV
AV - 73
Car Wings correspondence TV / Navigation system ( DVD method)
2. Allowed to run the car, NAVI Control unit vehicle-side harness connector
Compactors Six To check the voltage waveform between the turn pin-body earth.
ELF1080D
NG » • Constant voltage value (about 5V If the voltage waveform does not appear in the vicinity) to replace the combination meter
• Constant voltage value (about 0V If the voltage waveform does not appear in the vicinity) is NAVI To replace the control unit
2. Carry out the inspection of the brake warning light in the combination meter inside stepping on the parking brake.
unit vehicle-side harness connector Three To check the voltage between the turn pin-body
earth.
Measuring terminal
Measurement condition Reference value
(+) (-)
NG » NAVI Measurement terminal to repair the control unit - the parking brake switch between the harness
AV - 74
Car Wings correspondence TV / Navigation system ( DVD method)
2. NAVI control unit( TH Type Twelve Remove the connector of the pole).
3. And the key switch to the following measurement conditions, NAVI Control Unit
B
To vehicle side harness connector Five To check the voltage between the turn pin-body earth.
C
Measurement condition Reference value
(+) (-)
OFF about 0V
Body earth key SW
Five ACC about 0V
2. The shift position R The range, to inspect the shift position indicator on the combination meter inside.
By operating the select lever, NAVI Control unit vehicle-side harness connector Four To
Measuring terminal
Measurement condition Reference value
I
(+) (-)
NG » NAVI Control unit - IPDM CAB Measurement terminal to repair between harness AV
AV - 75
Car Wings correspondence TV / Navigation system ( DVD method)
1. BCM Self-diagnosis (communication diagnosis) inspection One ( BCM ~ NAVI Between the control unit)
BCM Perform self-diagnosis (communication diagnosis). " BCS Body Control System " " Communications Diagnostics " (BCS-34 page ) See.
NO » Two What
2. BCM Self-diagnosis (communication diagnosis) inspection Two ( BCM - Between centralized switch)
BCM To continue with the self-diagnosis (communication diagnosis), to confirm the following.
NO » Three What
Centralized switch ( NAVI Switch) of " map/ PLAY " Switch and " image quality " If the switch is working properly?
3. BCM Vehicle side harness connector Fifteen , 35 Ban terminal ~ centralized switch
Vehicle side harness connector Twelve , Six To check the continuity between the turn terminal.
4. BCM Vehicle side harness connector Fifteen , 35 Ban terminal ~ Body Architect
OK » Five What
AV - 76
Car Wings correspondence TV / Navigation system ( DVD method)
3. Centralized switch ( NAVI Operating the switch), BCM Vehicle side harness
connector Fifteen , 35 To check the voltage waveform between the turn pin-body earth.
B
SKIA3031J
Fifteen
Concentration SW ( NAVI
Body earth SKIA2946J
SW Press any)
35
SKIA2947J
F
NG » • Constant voltage value (about 5V If in the vicinity of) the voltage waveform does not appear to replace the centralized switch
G
• Constant voltage value (about 0V If the voltage waveform does not appear in the vicinity) is BCM To replace the
Vehicle side harness connector 14 , Two To check the continuity between the turn terminal.
I
19 ~ 14 : Yes conduction
OK » Seven What
AV - 77
Car Wings correspondence TV / Navigation system ( DVD method)
terminal.
OK » Eight What
1. BCM , TV Tuner and NAVI To connect the connector of the control unit.
Harness connector One , Twelve To check the voltage wave form between the turn pin-body earth.
Measuring terminal
Measurement condition Reference value
(+) (-)
One
Concentration SW ( NAVI
Body earth SKIA3022J
SW Press any)
Twelve
SKIA2553J
OK » Nine What
AV - 78
Car Wings correspondence TV / Navigation system ( DVD method)
Centralized switch ( NAVI Operating the switch), TV Tuner vehicle side harness connector Two , 14 To
measurement terminal B
Measurement condition Reference value
(+) (-)
Two
Concentration SW ( NAVI C
Body earth SKIA3035J
SW Press any)
14
SKIA2553J
D
Inspection results OK Or?
E
It does not appear at all screen (navigation, TV , Except for the video screen) JKS00BD8
2. Centralized switch ( NAVI Pressing the image quality switches of the switch).
H
BCM Perform self-diagnosis (communication diagnosis). " BCS Body Control System " " Communications Diagnostics " (BCS-34 page ) See.
JA
AV
AV - 79
Car Wings correspondence TV / Navigation system ( DVD method)
3. Harness inspection
Spray unit vehicle-side harness connector 13 , Fifteen To check the conduction of turn terminal.
4. BCM Vehicle side harness connector Sixteen , 37 Ban terminal ~ Body Architect
OK » Four What
3. Press the information switch, BCM Vehicle side harness connector Sixteen , 37 Turn
Measuring terminal
Measurement condition Reference value
(+) (-)
Sixteen body
Earth SKIA2620J
SKIA2559J
information SW Press
37 body
Earth
SKIA2566J
NG » • Constant voltage value (about 5V Replace the front display unit if in the vicinity of) the voltage waveform does not appear
• Constant voltage value (about 0V If the voltage waveform does not appear in the vicinity) is BCM To replace the
AV - 80
Car Wings correspondence TV / Navigation system ( DVD method)
1. Phenomenon confirmation
NO » " Failure diagnosis screen does not start "( AV-76 page ) To implement. E
3. NAVI Control unit vehicle-side harness connector twenty one , twenty four Turn
Terminal ~ TV Tuner vehicle side harness connector Sixteen , Five To check the continuity between the turn
terminal.
G
4. NAVI Control unit vehicle-side harness connector twenty one , twenty four Turn
H
To check the continuity between the terminals - body earth.
SKIA2878J
twenty one ~ Body earth : No conduction
I
Inspection results OK Or
OK » Three What
JA
AV
AV - 81
Car Wings correspondence TV / Navigation system ( DVD method)
Nectar twenty four Ban terminal ~ twenty one To check the voltage waveform between the turn terminal.
SKIA0186J
Inspection results OK Or
OK » Four What
Four. Harness inspection ( NAVI Control unit - the front display unit)
1. The key switch OFF To.
2. NAVI Control unit (T H Type Forty Remove the connector of the pole) and the front display unit.
28 ~ 19 : Yes conduction
Inspection results OK Or
OK » Three What
NG » NAVI Measurement terminal to repair the control unit - the front display unit between the harness
AV - 82
Car Wings correspondence TV / Navigation system ( DVD method)
1. NAVI To connect the connector of the control unit and the front display unit.
Nectar 28 Ban terminal ~ 26 To check the voltage waveform between the turn terminal.
B
D
SKIA0186J
Inspection results OK Or
2. NAVI control unit( TH Type Forty Pole) and TV tuner( TK Type twenty four Remove the connector of the pole).
3. NAVI Control unit vehicle-side harness connector twenty one , twenty three Turn
G
Terminal ~ TV Tuner vehicle side harness connector Sixteen , 17 To check the continuity between the turn
terminal.
4. NAVI Control unit vehicle-side harness connector twenty one , twenty three Turn
SKIA2879J
twenty one ~ Body earth : No conduction I
twenty three ~ Body earth : No conduction
OK » Two What
JA
NG » NAVI Control unit - TV Measurement terminal to repair the tuner between the harness
AV
AV - 83
Car Wings correspondence TV / Navigation system ( DVD method)
Nectar twenty three Ban terminal ~ twenty one To check the voltage waveform between the turn terminal.
SKIA0187J
Inspection results OK Or
OK » Three What
2. NAVI control unit( TH Type Forty Remove the connector of the pole) and the front display unit.
Terminal-front display unit vehicle side Hanesukoneku ter Twenty , twenty one To check the
SKIA2624J
twenty five ~ Body earth : No conduction
OK » Four What
NG » NAVI Measurement terminal to repair the control unit - the front display unit between the harness
AV - 84
Car Wings correspondence TV / Navigation system ( DVD method)
1. NAVI To connect the connector of the control unit and the front display unit.
Nectar twenty five Ban terminal ~ 26 To check the voltage waveform between the turn terminal.
B
D
SKIA0187J
Inspection results OK Or
OK » Five What
E
NG » NAVI To replace the control unit
TV The antenna feeder line and the glass antenna and visual inspection, a crack in the feeder line and the glass antenna, to check whether the disconnection is not "Antenna path" F
( AV-32 page ) A reference
1. Harness inspection H
AV
33 ~ Body earth : No conduction
L
OK » Two What
NG » NAVI Measurement terminal to repair the control unit - the front display unit between the harness
AV - 85
Car Wings correspondence TV / Navigation system ( DVD method)
1. NAVI To connect the connector of the control unit and the front display unit.
36 body
Earth TV SW Press SKIA2692J
SKIA0163J
Inspection results OK Or
OK » Three What
procedure Two Under the same conditions as, NAVI Control Unit 33 To check the voltage waveform between
Measuring terminal
Measurement condition Reference value
(+) (-)
33 body
Earth TV SW Press SKIA2693J
SKIA0162J
Inspection results OK Or
AV - 86
Car Wings correspondence TV / Navigation system ( DVD method)
1. Harness inspection
2. NAVI control unit( TH Type Forty Remove the connector of the pole) and the front display unit.
SKIA2607J D
Inspection results OK Or?
OK » Two What
NG » NAVI To repair the control unit - the front display unit between the harness
1. NAVI To connect the connector of the control unit and the front display unit.
3. "Screen adjustment" of the check and adjustment mode In the color bar display. " Confirmation - Adjustment mode "( AV-67 page ) reference
G
Measuring terminal
Measurement condition Reference value
(+) (-)
SKIA0164J I
AV
AV - 87
Car Wings correspondence TV / Navigation system ( DVD method)
2. Of check and adjustment mode " Screen Adjustment " In to check the color in the color bar display. " Confirmation - Adjustment mode "( AV-67 page )
See.
NG » Two What
2. Harness diagnosis
2. NAVI control unit( TH Type Forty Remove the connector of the pole) and the front display unit.
29 ~ Four (Check against time following all of the phenomenon): Yes conduction
29 - Body ground (to check for at the time of following all of the phenomenon) : No conduction
OK » Three What
NG » NAVI To repair the control unit - the front display unit between the harness
AV - 88
Car Wings correspondence TV / Navigation system ( DVD method)
1. NAVI To connect the connector of the control unit and the front display unit.
3. Color bars displayed on the screen adjustment of the check and adjustment mode. " Confirmation - Adjustment mode "( AV-67 page ) See.
4. NAVI Control unit vehicle-side harness connector 31 , 32 , 34 Ban terminal ~ 29 To check the voltage waveform between the turn terminal.
B
Caution : To inspect only abnormal pathway in response to the phenomenon
SKIA0166J
E
When the yellow Cal
Measuring terminal
Measurement condition Reference value
(+) (-)
F
Display the "color
bar display" in
32 29 check and
adjustment mode
G
SKIA0167J
Measuring terminal
Measurement condition Reference value H
(+) (-)
SKIA0165J
JA
Inspection results OK Or?
AV
AV - 89
Car Wings correspondence TV / Navigation system ( DVD method)
Centralized switch ( NAVI You can not navigate operation on the switch) JKS00BF2
1. Self-diagnosis inspection
2. Perform a self-diagnostic mode. " Self-diagnostic mode "( AV-60 page ) See.
NO »If a fault diagnosis screen does not start "Failure diagnosis screen does not start" ( AV-76 page ) To implement the
Checklist
• Do not be too far from the microphone (in the overhead console).
• Voice of the steering wheel switch " Voice command " Press the switch "please the command" can not be recognized and not from being
uttered.
OK » Two What
2. To start the fault diagnosis screen. " Fault diagnosis function "( AV-59 page ) See.
Caution : If you can not start the fault diagnosis screen, " Failure diagnosis screen does not start "( AV-76 page ) To implement.
3. Confirmation - To select the adjustment mode. " Confirmation - Adjustment mode "( AV-67 page ) See.
Four. " Communication modem settings " Select the, "Mike - To select a speaker verification ". " Communication modem settings " (AV-69 page ) See.
NO » Three What
AV - 90
Car Wings correspondence TV / Navigation system ( DVD method)
3. Harness inspection
2. NAVI control unit( TH Type Forty Pole) and remove the connector of the microphone.
3. Press the voice command switch to say the voice into the microphone.
G
4. NAVI Control unit vehicle-side harness connector Fifty Ban terminal
~ 49 To check the voltage between the turn terminal.
Measuring terminal
Measurement condition Reference value
(+) (-) H
Fifty 49 - about 5V
Measuring terminal
Measurement condition Reference value
(+) (-)
JA
AV
SKIA2557J
SKIA2905J
AV - 91
Car Wings correspondence TV / Navigation system ( DVD method)
Even if you press the voice command switch VOICE MENU There does not appear JKS00BF4
1. Communications Diagnostics
2. To start the fault diagnosis screen. " Fault diagnosis function "( AV-59 page ) See.
NO » " Failure diagnosis screen does not start "( AV-76 page ) To implement.
NO » Three What
3. Harness inspection
2. Disconnection to harness between the spiral cable - steering wheel switch or visual inspection no.
NG »To repair the spiral cable - steering wheel switch between the harness
The key switch ON To, to check the following do the navigation operation.
• Guide settings OFF Or not has become? Reference: • Traveling on a dark pink route, voice
• Since the audio guide is not carried out only at an intersection marked with certain conditions are met ○ mark there (guide pin), on the route there is a case in which
they change direction not the voice guide
Inspection results OK Or
OK » Two What
1. To start the "failure diagnosis screen". " Fault diagnosis function "( AV-59 page ) See.
Caution : If the "failure diagnosis screen" does not start, " Failure diagnosis screen does not start "( AV-76 page ) To implement.
2. Select the screen switch, " To implement the voice guide confirmation ". " Audio guide confirmation "( AV-70 page ) See.
Or confirmation tone is output from the front right side of the speaker?
NG » Three What
AV - 92
Car Wings correspondence TV / Navigation system ( DVD method)
NO » Four What
B
2. NAVI control unit( TH Type Forty Pole) and electronic tuner radio connector ( A16 Remove the pole). C
27 , twenty two , twenty one To check the continuity between the turn terminal.
D
39 ~ 27 : Yes conduction
Inspection results OK Or
OK » Five What
NG » NAVI To repair the harness between the control unit - electronic tuner radio G
JA
AV
AV - 93
Car Wings correspondence TV / Navigation system ( DVD method)
1. NAVI To connect the connector of the control unit and electronic tuner radio.
3. In measurement under the following conditions, NAVI Control unit vehicle-side harness
Four. And it outputs the guide voice, NAVI Control unit vehicle-side harness
Scan connector 41 , 42 The voltage waveform between the turn pin-body earth to point inspection.
Measuring terminal
Measurement condition Reference value
(+) (-)
41
42 output
SKIA0171J
Inspection results OK Or
1. Phenomenon confirmation
NO » Two What
Inspection results OK Or
OK » Three What
AV - 94
Car Wings correspondence TV / Navigation system ( DVD method)
1. Phenomenon confirmation
C
1. The key switch ON To.
2. Light switch ( One The stage) ON And, combination in when exposed to light and when I blocked by hand the auto light sensor
To verify that the brightness of the meter changes. (Automatic dimming function)
NO »Carry out the inspection of the auto light system. " Auto light receiving sensor system inspection "( LT-13 page ) See.
• Of check and adjustment mode "Vehicle signal diagnosis" ( AV-68 page ) In diagnosing the following items.
Stage : ON
Caution : In conjunction with the light switch on the brightness outside the vehicle ON / OFF There is a case in which not (automatic dimming function)
G
Inspection results OK Or?
NG » Three What
H
3. Harness inspection
2. NAVI control unit( TH Type Twelve Pole) and BCM Remove the connector.
I
3. NAVI Control unit vehicle-side harness connector Eight Ban terminal
~ BCM Vehicle side harness connector 14 You check the continuity between the turn terminal.
Inspection results OK Or
OK » Four What
AV - 95
Car Wings correspondence TV / Navigation system ( DVD method)
Measuring terminal
Measurement condition Reference value
(+) (-)
(one step)
At the time of vehicle stop TV Even but not bitterness movies or while traveling TV Reflected is JKS00C22
1. Communication inspection
2. To start the fault diagnosis screen. " Fault diagnosis function "( AV-59 page ) See.
NO » " Failure diagnosis screen does not start "( AV-76 page ) To implement.
2. Confirmation - Of the adjustment mode "Vehicle signal diagnosis" ( AV-68 page ) In a state in which the switching on, TV Reproduce the running state would be reflected
<Vehicle speed
At stop : OFF
<Reverse signal>
Step on the parking brake : ON
Inspection results OK Or
NG »Carry out the inspection of the appropriate signal system. Vehicle speed signal inspection "Vehicle speed signal inspection" ( AV-73 page ) And parking Breakfast
Rake signal inspection "Parking brake signal inspection" ( AV-74 page ) See.
AV - 96
Car Wings correspondence TV / Navigation system ( DVD method)
TV Voice does not come out from all seats speaker JKS00BDE
1. Phenomenon confirmation
NO » Four What
C
2. Harness inspection
Twenty , 19 , twenty one , Six , Eight To check the continuity between the turn ends.
E
43 ~ Twenty : Yes conduction
44 ~ 19 : Yes conduction
Inspection results OK Or
OK » Three What
I
NG » NAVI Control unit - TV To repair the tuner between the harness
JA
AV
AV - 97
Car Wings correspondence TV / Navigation system ( DVD method)
44 , 45 , 46 , 48 Ban terminal ~ 43 To check the voltage waveform between the turn terminal.
44
45
46
43 TV During the broadcast reception
SKIA2628J
48
SKIA0177J
Inspection results OK Or
NAVI Between the control unit - electronic tuner radio DIN Bad connection or pin missing to check whether or not there in the Cave.
Inspection results OK Or
OK » Five What
NG » DIN Reconnect the cable, carry out the phenomenon confirmation again.
Replace the other normal electronic tuner radio performs phenomenon check again.
TV Voice does not come out only from the front speakers JKS00C2M
" No sound only from the front speakers "( AV-22 page ) See.
TV Voice does not come out only from the rear speakers JKS00C2N
" No sound only from the rear speakers (car Wings corresponding TV / Navigation system ( DVD Method) attaching car only ) " (AV23 page ) See. Measuring terminal
AV - 98
Car Wings correspondence TV / Navigation system ( DVD method)
Fuel consumption information does not come out (Display of average fuel consumption is also traveling and cruising distance is " ** " become)
JKS00BDJ
2. BCM Perform self-diagnosis (communication diagnosis). " BCS Body Control System " " Communications Diagnostics " (BCS-34 page ) See. B
NO » BCM Perform the fault diagnosis. " BCS Body Control System " " CONSULT - Ⅱ function of " (BCS-31
page ) See. C
2. Harness inspection
Spray unit vehicle-side harness connector 13 , Fifteen To check the conduction of turn terminal.
4. BCM Vehicle side harness connector Sixteen , 37 Ban terminal ~ Body Architect F
To check the continuity between the vinegar.
G
Inspection results OK Or?
OK » Three What
JA
AV
AV - 99
Car Wings correspondence TV / Navigation system ( DVD method)
3. Press the information switch, BCM Vehicle side harness connector Sixteen , 37 Turn
Measuring terminal
Measurement condition Reference value
(+) (-)
Sixteen body
Earth SKIA2620J
SKIA2559J
information SW Press
37 body
Earth
SKIA2566J
NG » • Constant voltage value (about 5V Replace the front display unit if in the vicinity of) the voltage waveform does not appear
• Constant voltage value (about 0V If the voltage waveform does not appear in the vicinity) is BCM To replace the
NO »Conduct a vehicle speed signal inspection. " DI Driver Information System " "How to proceed with fault diagnosis" ( DI-17
page ) See.
BCM Perform self-diagnosis (communication diagnosis). " BCS Body Control System " " Communications Diagnostics " (BCS-34 page ) See.
OK » Three What
NG » BCM Perform the fault diagnosis. " BCS Body Control System " " CONSULT - Ⅱ function of " (BCS-31
page ) See.
AV - 100
Car Wings correspondence TV / Navigation system ( DVD method)
3. Harness inspection
Spray unit vehicle-side harness connector 13 , Fifteen To check the conduction of turn terminal.
B
Sixteen ~ 13 : Yes conduction
3. BCM Vehicle side harness connector Sixteen , 37 Ban terminal ~ Body Architect
OK » Four What
E
Four. Communication signal inspection
3. Press the information switch, BCM Vehicle side harness connector Sixteen , 37 Turn
F
Measuring terminal
Measurement condition Reference value
(+) (-) G
Sixteen body
Earth SKIA2620J H
SKIA2559J
information SW Press
37 body
Earth
JA
SKIA2566J
NG » • Constant voltage value (about 5V Replace the front display unit if in the vicinity of) the voltage waveform does not appear AV
• Constant voltage value (about 0V If the voltage waveform does not appear in the vicinity) is BCM To replace the
AV - 101
Car Wings correspondence TV / Navigation system ( DVD method)
Warning screen does not appear (excluding the charge warning display) JKS00BDL
Display conditions
Dragging parking brake warning PKB Switch ON In the vehicle speed is about 5km / h When it becomes more than
Door ajar warning Each door switch ON In the vehicle speed is about 5km / h When it becomes more than
Other than those above When the meter within the warning light is lit
» Two What
BCM Perform self-diagnosis (communication diagnosis). " BCS Body Control System " " Communications Diagnostics " (BCS-34 page ) See.
NO » BCM Perform the fault diagnosis. " BCS Body Control System " " CONSULT - Ⅱ function of " (BCS-31
page ) See.
3. Harness inspection
Spray unit vehicle-side harness connector 13 , Fifteen To check the conduction of turn terminal.
3. BCM Vehicle side harness connector Sixteen , 37 Ban terminal ~ Body Architect
OK » Four What
NG » BCM Display item to repair the harness between the ~ front display unit
AV - 102
Car Wings correspondence TV / Navigation system ( DVD method)
1. BCM And to connect the harness connector of the front display unit.
3. Press the information switch, BCM Vehicle side harness connector of Sixteen , 37
Measuring terminal
Measurement condition Reference value
(+) (-)
Sixteen body
Earth SKIA2620J
D
SKIA2559J
information SW Press
37 body E
Earth
SKIA2566J
F
Inspection results OK Or?
NG » • Constant voltage value (about 5V Replace the front display unit if in the vicinity of) the voltage waveform does not appear
• Constant voltage value (about 0V If the voltage waveform does not appear in the vicinity) is BCM To replace the
G
OK » Two What I
NG To »repair or replace the appropriate site
2. Communication inspection
JA
To start the fault diagnosis screen. " Fault diagnosis function "( AV-59 page ) See.
NO » • If the connection is abnormal "Inspection by the diagnostic result" ( AV-61 page ) To implement the
AV
• If the failure diagnosis screen does not start, " Failure diagnosis screen does not start "( AV-76 page ) To implement the
AV - 103
Car Wings correspondence TV / Navigation system ( DVD method)
1. Phenomenon confirmation
" Phenomenon example not unusual "( AV-107 page ) Or phenomenon example corresponding want to?
NG » Two What
2. Navigation adjustment
1. The key switch ON To.
2. Carry out the navigation adjustment in the confirmation and adjustment mode. " Navigation adjustment "( AV-69 page ) See.
YES »Exit
NO » Three What
To select the error history in fault diagnosis screen. " Error history mode "( AV-65 page ) See.
YES » " Diagnosis by the error history "( AV-65 page ) What
NO » Four What
AV - 104
Car Wings correspondence TV / Navigation system ( DVD method)
2. Of check and adjustment mode "Vehicle signal diagnosis" ( AV-68 page ) In diagnosing the following items.
<Vehicle speed
NG » • The vehicle speed is NG When the "Vehicle speed signal inspection" ( AV-73 page ) What
D
• Reverse is NG When the "Reverse signal inspection" ( AV-75 page ) What
2. Of check and adjustment mode "Vehicle signal diagnosis" ( AV-68 page ) In diagnosing the following items.
F
<Vehicle speed
At stop : OFF
• Reverse is NG When, " Reverse signal inspection "( AV-75 page ) What
1. Navigation adjustment
1. Carry out the navigation adjustment in the confirmation and adjustment mode. " Navigation adjustment "( AV-69 page ) See.
JA
2. Traveling to confirm the phenomenon.
YES »Exit
NO » Two What
AV
AV - 105
Car Wings correspondence TV / Navigation system ( DVD method)
To select the error history in fault diagnosis screen. " Error history mode "( AV-65 page ) See.
YES » " Diagnosis by the error history "( AV-65 page ) What
GPS It does not receive the radio waves from satellites JKS00BDR
1. Environment confirmation
GPS Or mobile phone and the like have been placed to generate the metallic objects and radio blocking the radio waves in the vicinity of the antenna. Further, if it is blocked by buildings.
OK » • Not a malfunction.
Or it blocked the sky in a metal thing, and or there is a thing that generates radio waves GPS You may not be able to receive radio waves from a satellite.
NG » Two What
2. self-diagnosis
Perform a self-diagnostic mode. " Self-diagnostic mode "( AV-60 page ) See.
NG »To check the abnormal region. " Diagnostic number table "( AV-157 page ) See.
• "When the fault diagnosis screen" does not start "Failure diagnosis screen does not start" ( AV-76 page ) To implement.
• NAVI Control unit - GPS If there is abnormality between the antennas, " NAVI Control Unit and GPS When the connection of the
antenna is of abnormal "( AV-161 page ) To implement.
Caution : Since having an automatic distance correction function, but usually do not require adjustment, if fitted with tire chains, etc. Thailand
Four. After the real running, " Phenomenon example not unusual "( AV-107 page ) If there is content corresponding to.
NG » Two What
AV - 106
Car Wings correspondence TV / Navigation system ( DVD method)
- Test Method: NAVI And it is connected to the control unit GPS Antenna harness connector ( GT5 ) Remove the, currently traveling position, the
azimuth from exactly fit.
B
The practice of the present traveling test at the time of the following phenomenon.
• <Well in the same place or fly the current position mark, GPS When either the judge by>
• <If you want to know whether correct or not the shape of the road that are displayed> Reference: This time to compare the shape and trajectory of the map. It should be noted, is to be able to
• <Exactly when to adjust the distance> Reference: At this time, traveling on a course you know the exact distance (distance of the highway post, etc.), increase or decrease with respect to the
real distance
Minute is calculated.
D
Correction value = One - A / BA :
B : Actual distance
• When the map errors, please point out the error location.
The video does not appear. Brightness adjustment of the display is set to full To re-adjust the brightness of the display.
to darker.
Guide No sound. The volume adjustment OFF , Set to the minimum or maximum. To adjust the guide volume.
H
Is the volume of the audio guide is small or
large.
Traveling on a dark pink route, voice guide is not Not a malfunction.
performed.
Screen is dark. The operation of Car temperature is low. To wait until the temperature inside the vehicle is suitable temperature.
Map screen and Bird view ® Place name displayed on As the screen is not complicated, it is performed thinning-out Not a malfunction.
the screen is different. processing of the character information. In addition there is also
The vehicle position may not be displayed The car of the key switch OFF Moving the car by other means GPS While traveling in the receiving state.
correctly. from then on. For example, move in, such as ferry and vehicle
transporters.
L
AV - 107
Car Wings correspondence TV / Navigation system ( DVD method)
A light switch ON Not a screen at night In the "Display switching" at the time of the previous screen dimming Reset the screen to Iorga surface with a "display switch" at the time
even in the. that have been left switched the night screen in the daytime screen. of the screen dimming.
Map does not scroll is also possible to move Not in the current location display. You are here to display by pressing the "map" switch.
the vehicle.
Vehicle mark is not displayed. Not in the current location display You are here to display by pressing the "map" switch.
Accuracy display on the map screen ( GPS Since it is in the shadow of the indoor and buildings GPS Signal To move to a good place outdoor outlook.
Satellite mark) also remain gray forever. is blocked.
Because it has put the things in combination meter Do not place any object on the combination meter
upper right, GPS Signal can not be received. upper right.
GPS Placement of the satellite is bad. Wait until the arrangement is improved.
Vehicle position accuracy is poor. Accuracy display on the map screen ( GPS Satellite You are here has not been able to fix.
mark) even that is still in the gray forever.
Mounting of the tire chain, by changing mounted to other vehicle of For a while (approximately 30km / h In speed Thirty
the present system, shift the vehicle speed setting from the vehicle Automatically adjust will and minute about) traveling. If you still
speed pulse (leading or lagging) occurs. proceed or delay occurs, do the distance adjustment in the
There is an error or omission in the terrain data. (Shifted to the Map DVD-ROM As a rule, One yearly One
same place to always) Times updated version will be announced.
During the re-search, I do not want to search for Already passed the transit point, or were judged to have passed. If you want to via a waypoint that has passed through again,
Route information is not displayed. Do not go the route search. Set the destination, it makes the route search.
It has a list covers vehicle mark on the recommended route. Traveling at a recommended route.
Dark pink route, do not indicate the route information table. Not a malfunction.
After the route search, even through the vicinity of Yet such have the vehicle mark is traveling on the recommended Traveling on the recommended route.
the toll road entrance, guiding symbol does not route. (Guide sign, display the only mark that the recommended route
From the vehicle mark 50km Not a failure there is no more guidance symbol
It can not be auto-discovery. Running a major District towns and villages road (gray of the road). Or Traveling on a search target road. Or manually restart
there is no recommended route. the search again.
It was the automatic detour search (or detour Was searched in consideration of various conditions, but the same Not a malfunction.
exploration search), but intends want is the same results.
result as the previous search routes.
Stopover can not be set. Stopover is Five It is set or more locations. Waypoint Five More locations process is not performed be set.
Routing in the place of departure is not Na The starting point of the route setting is always ing to the current Not a malfunction.
choose. location.
Menu item does not choose some. The vehicle is traveling. The car was allowed to stop in a safe place, and operations.
AV - 108
Car Wings correspondence TV / Navigation system ( DVD method)
Not voice guide. Since the audio guide is not carried out only at an intersection that Not a malfunction.
have been marked as certain conditions are met ○ there, on the
route there is a case in which they change direction not the voice
guide.
It is out of the recommended route. To return to the recommended route, it performed again route
B
search.
Audio guide OFF It has become. The setting of the voice guide ON To.
Guidance is different from the actual road. Direction the contents of the audio guide is to be right or left turn, other Traveling child and according to the actual traffic rules. C
There is a case to be of different contents by such form of
connection with the road.
Calling it would be recognized not work Noise is recognized. Close the window. Such as an electronic tuner radio AV Lower the
Press the voice command switch of the steering wheel Press the voice command switch of the steering wheel F
switch or we release the finger Ten Seconds or more switch or we release the finger Ten To make start
have passed. talking within seconds.
Route does not appear. There is no search target road in the vicinity of the destination. A destination close to the orange or more of the thick road
in places like the road in the uplink and downlink are displayed in a
You are here, there is a condition regulation in the vicinity of the The search conditions of the time regulatory requirements OFF To. In
destination (day of the week, time). the search conditions (avoid the regulation time) OFF
I
To.
Route is displayed interrupted. In the search, the main city road (gray road Not a malfunction.
Because of the area that does not use the road) note) , Ri
You are here or via point is displayed in the middle, or
choppy.
JA
They are searched in different conditions the search By the distance to the destination (waypoint), it is searched
Not a malfunction.
conditions. at a fee road priority.
Recommended route that passed is Since the recommended route is managed in each section, Not a malfunction.
erased. stopover One The passing and transit point from the
starting point One To erase the data of up to. (More Ru if
AV
not erased by Area)
AV - 109
Car Wings correspondence TV / Navigation system ( DVD method)
In the search, the main city roads Note because there Set close to the basic road (other than the gray of the
are areas that do not use (gray roads)), may become road).
roundabout route.
Point of departure, there is a regulation on the road in the vicinity of Try setting shifted slightly the departure point and
the destination (one-way, etc.) which may give a circuitous route at destination. Or try to set a waypoint to the route you want
the time. street.
Main city road ( DVD-ROM The area used for Not a malfunction.
searching the gray road), since the priority to turn left
in the vicinity of the current and destination
(waypoint), may become detour.
Display of the land mark is different from the There are a Okoruko by the flaws and errors in the terrain Map DVD-ROM As a rule, One yearly One
actual. data. Since the times updated version is the announcement wait one thing
to it.
Departure, stopover, Charles argument is the The starting point on the map, via land, because that does not Setting a destination close to on the road. In the case of just Shi
display, if you
recommended do not
route return
from to the correct
the destination position
to the awayeven contain
when traveling
data forfor a while,
route searchto correct the current
in the vicinity of theposition. Explore
destination, the the roundabout a recommended
road near the main townsroute.
and villages District road (gray of the
points. start of the route guide, via, the end point would away. road), there is a case in which the recommended route is drawn
Note): non-designated cities, and the prefectural capital (which may vary depending on the updating of the map disc).
Read the mileage and the turning angle of the vehicle, and the traveling, such as the following in order to have to calculate the movement of the vehicle, caused the error to the current position
ELK0454D
AV - 110
Car Wings correspondence TV / Navigation system ( DVD method)
Cause (situation) -: running ooo :display Driving condition Remarks (such as treatment)
Y Shaped road
ELK0192D
Spiral-shaped road
ELK0193D
D
Straight road
ELK0194D
10km Even if the extent of travel, position correction if it
The shape of the road does not return to the correct position, do the
Winding road orientation corrections as necessary.
road.
G
ELK0195D
Grid road
ELK0196D
I
As a high-speed road and side road, if there is a
road of orientation similar to the close, accidentally
matching, which may then deviate from the road.
ELK0197D
JA
AV
AV - 111
Car Wings correspondence TV / Navigation system ( DVD method)
Cause (situation) -: running ooo :display Driving condition Remarks (such as treatment)
Parking, etc. Such as the parking lot, when you run the place
without a map on the road, matching accidentally
in the vicinity of the road, there is a thing that is
out of the correct position when you return to the
road. Also, when repeating the turning and
crosscut, azimuth error is cumulative, it may not
ride correctly road.
ELK0198D
Turntable
Key switch OFF For when the navigation
system is not able to obtain the signal
from the gyro (angular speed sensor),
place key switch
OFF Turning Then the turn table at the time,
orientation is sometimes difficult to return to the
crazy right path.
ELK0199D
the right path. 10km Even if the extent of travel, position correction if it
Slope Put the garage of a hill, caused an error of the turning does not return to the correct position, do the
angle vehicle such as a bank the road is handed time in orientation corrections as necessary.
road.
ELK0200D
ELK0201D
AV - 112
Car Wings correspondence TV / Navigation system ( DVD method)
Cause (situation) -: running ooo :display Driving condition Remarks (such as treatment)
B
ELK0251D
ELK0252D
D
Displaying a completely different location is the current position mark
If such as the following, GPS Depending on the reception status of, there may be displayed the current position mark in a completely different location. In such a case, position correction, perform the
orientation correction.
position mark will not return while I went to a completely different location. It should be noted that, GPS If radio waves received from the satellite, position is corrected.
The following cases, automatically because the current position is corrected, there may seem to jump the current position mark. G
- When the map matching, if the current position and the current position mark is misaligned, feels like it current position mark is jumped. At this time, there is to be position correction to
- GPS It adopted a positioning position by, when the position correction, if the current position and the current position mark is misaligned, feels like he is the current position mark
jumped. In this case, it may be positioned fixed in place without a separate road incorrectly.
Also traveling on the same road, there are times when you do not shift and when the current position mark is shifted
GPS antenna( GPS Information) or a gyro (angular velocity sensor state of) is changing from moment to moment, the position detection results by the running lane and JA
handle operation is different. Therefore, it may deviate by the state also always off not road.
GPS To display the reception is green, it does not return to the correct position
• GPS The accuracy, 10m There is a degree of error, GPS There is a call to be position correction does not ride on the road current position mark is correct by. How to position correction
L
AV - 113
Car Wings correspondence TV / Navigation system ( DVD method)
• In the navigation system, GPS The position detection result of a comparison between the position detection result of the map matching, to adopt the position of the person accuracy is
determined to be.
• When the vehicle is stopped, GPS Position correction by is sometimes not carried out.
If there is no place name displayed on the map screen, which may place name currently not displayed.
Birdview ® Display contents are different in the (plane) map screen display
• Moving distance of the vehicle until the update of the screen, turning angle is longer than the time of (planar) map display.
• Road, display conditions, such as place names are different in the front display unit and far display unit.
• Because the display is performing a thinning-out process of character information so as not to complicated, display contents vary depending on the case and the time.
• Same place name, there is possible to display multiple road names and the like.
SKIA3037J
AV - 114
Car Wings correspondence TV / Navigation system ( DVD method)
removal
1. Installation lower center panel ASSY A remove. " IP Instrument panel "of "Removing, mounting" ( IP-5
page ) See.
2. Remove the front floor duct. " ATC Auto air conditioner "of "Removing the floor duct" ( ATC-110
B
page ) See.
3. Mounting screw ( Four Book) and disconnect the harness connector, NAVI Co
PKIA1286J
Four. Mounting screw ( Four Remove the book), remove the bracket. E
PKIA1287J
G
attachment
Installation is carried out in the reverse order of removal.
removal
1. Remove the installation upper garnish. " IP Instrument panel "of " Removal, installation " (IP-5 page) See.
I
2. Mounting screw ( Two Book) and disconnect the harness connector, GPS A
JA
AV
PKIA1288J
attachment
Installation is carried out in the reverse order of removal.
L
AV - 115
Car Wings correspondence TV / Navigation system ( DVD method)
removal
1. Centralized switch ( NAVI Winding a tape cut-out portion of the switch) lower
Insert a flat-blade screwdriver, etc. was, centralized switch ( NAVI Lift to remove the
switch).
2. Centralized switch ( NAVI Switch) takes the harness connector on the back
remove.
PKIA1289J
attachment
Installation is carried out in the reverse order of removal.
removal
1. Remove the combination meter. " DI Driver Information System " "Combination Mae
Removal of tar, mounting "( DI-25 page ) See.
2. Mounting bolts ( Four Book) and disconnect the harness connector, front di
PKIA1290J
attachment
Installation is carried out in the reverse order of removal.
AV - 116
Car Wings correspondence TV / Navigation system ( DVD method)
PKIA1291J F
Four. Front display unit Five. Navi finisher A 6. Illumination control scan
Switch ASSY
7. Meter bracket 8. Power box
G
1. Mounting screw ( Two Remove the book), illumination control scan
Switch ASSY A remove.
2. Mounting screw ( Seven Remove the book), take the meter bracket cover
remove. H
3. Mounting screw ( One This), nails ( Two Remove the point), Navi finisher
B A remove.
I
SKIA2488J
Four. Front display unit the back surface of the flexible print server
Unlock the kit fixed clip and connector.
JA
Five. Withdrawal of the flexible printed circuit from the connector.
AV
PKIA1292J
AV - 117
Car Wings correspondence TV / Navigation system ( DVD method)
6. Mounting screw ( Four Remove the book), remove the power supply box.
PKIA1293J
8. Front display unit mounting screw ( Four Remove the book), off
Remove the Ron To display unit.
PKIA1294J
removal
PKIA1299J
attachment
Installation is carried out in the reverse order of removal.
AV - 118
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
The navigation system, the moving distance of the vehicle obtained from the vehicle speed sensor, turning angle of the
vehicle obtained from a gyro (angular velocity sensor) and GPS Antenna ( GPS The traveling direction of the vehicle
obtained from information) Three To calculate the current position at a certain period from the type of signal. This and
B
the calculated current position DVD-ROM Map that contains the drive
DVD-ROM It specifies the current position by comparing the map data read from the
(map matching), and displays the current position mark on the display.
C
EL-2956D
It should be noted that, GPS Comparing the position detection result by the position detection result and map matching
D
of the vehicle obtained from, using the location data accuracy is determined to be. At the time of calculating the current
position to detect the moving distance and traveling direction of change between the from the previous calculation point
EL-0469D
Moving distance
Moving distance of the vehicle is calculated by an input signal from the vehicle speed sensor. Thus, due to wear of the tire, since the correct distance reduces that it will not be
G
Direction of travel
Change of course of the vehicle, a gyro (angular velocity sensor) and GPS antenna( GPS Calculated by information). this Two One to have each of the advantages and disadvantages, this
depending on the situation Two While prioritize the Tsukara of the signal, this according to the more accurate traveling direction status Two Changing the priority of Tsukara the signal to detect
Gyro (angular velocity sensor) • The turning angle can be very accurately detected. • Errors are accumulated for a long time continuous running.
• When the vehicle speed is slow it can not detect the correct
GPS antenna( GPS information) • Direction in which the progress of the vehicle (north, south, east and west)
It can be detected. orientation.
I
Map-matching
The map matching, the calculated current position by the method described by the position detection principle DVD-ROM
Map stored in the drive DVD-ROM Compared to the surrounding road map data elaborate read from Note, a
JA
function for correcting the current position on the most accurate and was estimated road. Therefore, in the
case of the following, GPS When information is received difficult situation, because there may not be corrected
properly after Barack traveling, there is a need to modify the current position mark manually.
AV
Caution : Road map data map DVD-ROM And the data in the based on
There.
ELK0097D
AV - 119
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
• The map matching, in addition to roads and position correction is determined that the vehicle is currently
Therefore, if the distance or azimuth has an error, the error priority of roads that are
candidates also occurs that the position fix to the wrong road. Also, in places like roads are
run in parallel, the priority about the same next to both roads, and the like delicate steering
and road shape, the current position mark is displayed alternately on both road there is.
EL-0470D
• In such as traveling to that road is new, map DVD-ROM If you have not been recorded, the
map matching is not possible to. Also it can not be performed correctly map matching may
Therefore, when traveling on the road is not on the map, and map matching to another road that are
not currently running, there is that the current position mark would have been displayed on the road.
Thereafter, when the road is actually traveling could detect is sometimes jump the current position
• Distance and position and the traveling direction calculated by the orientation map DVD-ROM Because the range is limited to be able to compare the
EL-0471D
pressurized et al read road data, if the degree more than the current position is shifted Ru Oh, it can not be modified in the correct position in the
map matching.
operating, GPS satellite( NAVSTAR ) Is, an altitude of about 21,000km And it transmits radio waves while orbiting the
GPS The receiver, Four One or more of the GPS Ri by the time difference between the radio waves arriving from the
satellite, of the vehicle Three Position dimension (latitude, longitude, altitude) is calculated. ( Three Dimension
measurement position) GPS Radio waves from a satellite Three Only when you can not receive One is Four Horn GPS
Using the altitude data when determined using the satellite Two To calculate the position of dimensions (latitude,
longitude). ( Two Dimension positioning) the following cases GPS Accuracy is poor.
ELK0098D
• Two In the dimension positioning, accuracy is degraded when the altitude of the vehicle position changes.
• Position detection performance, high accuracy Three Even in dimension positioning 10m There is a degree of error. Further, accuracy is utilized for positioning GPS Due to the influence of the
placement of the satellite, GPS Depending on the arrangement of the satellite position detection performance is reduced.
• In the tunnel, parking in the building, such as under the elevated highway, GPS If the radio waves from the satellite can not be received, it can not position detection. Also, GPS When you place an
object on top of the antenna of use, GPS It may be radio wave from a satellite can not be received.
AV - 120
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
• NAVI When the control unit exchange, map before you remove the battery DVD-ROM It is taken out.
• NAVI Because the following items are memory to the control unit, at the time of unit exchange ahead of the memory contents, to re-enter if necessary.
• Dimming switch
B
• Display color switching
[ Navi mode relationship] • The previous display last state (the map screen / Bird view, scale, of the map screen rotation state, of Rutoga Ido ON / OFF , The
trajectory ON / OFF etc)
• present location
D
Reference: Only remove the battery, memory is not erased.
System summary
E
• Combination meter (meter control unit ASSY A warning signal from the) CAN communication( H line, L More in line) BCM But it received, BCM To
display a warning screen by sending to the front display unit from.
• Warning screen ( RGB Image data) are memory inside the front display unit, BCM To interrupt displays a warning screen to the navigation screen through
the communication with the front Display unit with.
F
• Warning display displays the name and the address the contents of the vehicle abnormal site on the front display. In addition, the interrupt display-law warning or abnormal is not
resolved.
System chart
G
JA
PKIA1756J
AV
AV - 121
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
SKIA2520J
SKIA2521J
●: Submit ○: reception
● ○
A / T Electronic control system warning signal
○ ●
door SW signal ● ○ ○ ○
○ ●
Oil pressure warning signal
● ○
AV - 122
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
● ○
ABS Warning light signal C
○ ●
D
type 3 / type Four
SKIA2522J
I
SKIA2523J
●: Submit ○: reception
In Terri
Con
Jefferies Con
To Adaptive Laser
cement bi JA
Low cruise VDC / radar
key Yu Natick Steering
Luba control TCS / sensor nickel To reference
IPDM E /
The main signal name / Connection unit ECCS BCM tion angle
C/U valve systems ABS C / R
meter sensor
ASSY U
- A / TC / C/U
U One AV
AV - 123
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
In Terri
Con
Jefferies Con
To Adaptive Laser
cement bi
Low cruise VDC / radar
key Yu Natick Steering
Luba control TCS / sensor nickel To reference
IPDM E /
The main signal name / Connection unit ECCS BCM tion angle
C/U valve systems ABS C / R
meter sensor
ASSY U
- A / TC / C/U
U One
) ● ○
● ○
A / T Electronic control system warning signal
○ ●
door SW signal ● ○ ○ ○
○ ●
Oil pressure warning signal
● ○
● ○
ABS Warning light signal
○ ●
Reference :( One ) Intelligent Key unit attaching car only vehicle speed signal ( VDC
AV - 124
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
C
SKIA2524J
SKIA2525J
●: Submit ○: reception
F
ABS
Control
Aku Ju Intelligent Combi
Transformer valve
er ter Kiyuni' To reference Nesho IPDM E /
The main signal name / Connection unit ECCS fur BCM One
C/U Nme ter R
C/U ASSY -
A / TC / U
C/U G
● ○
A / T Electronic control system warning signal
I
○ ●
door SW signal ● ○ ○ ○
○ ●
Oil pressure warning signal
● ○
JA
Fuel consumption monitor signal ● ○
AV - 125
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
ABS
Control
Aku Ju Intelligent Combi
Transformer valve
er ter Kiyuni' To reference Nesho IPDM E /
The main signal name / Connection unit ECCS fur BCM One
C/U Nme ter R
C/U ASSY -
A / TC / U
C/U
● ○
ABS Warning light signal
○ ●
SKIA2526J
SKIA2527J
●: Submit ○: reception
Con In Terri
To Jefferies Con
Adaptive Laser
Transformer Low cement bi
cruise VDC / radar
ECC file over C Luba key Yu Natick Steering
control TCS / sensor IPDM E /
The main signal name / Connection unit SC / /U valve BCM nickel tion angle
systems ABS C / R
U ASS To Reference meter sensor
U
Y- One
C/U
A / TC
/U
AV - 126
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Con In Terri
To Jefferies Con
Adaptive Laser
Transformer Low cement bi
cruise VDC / radar
ECC file over C Luba key Yu Natick Steering
control TCS / sensor IPDM E /
The main signal name / Connection unit SC / /U valve BCM nickel tion angle
systems ABS C / R
U ASS To Reference meter sensor
U
Y- One
C/U
A / TC
B
/U
) ○ ○ ○ ● ○
door SW signal ● ○ ○ ○
○ ●
Oil pressure warning signal D
● ○
● ○
ABS Warning light signal
○ ●
Reference :( One ) Intelligent Key unit attaching car only vehicle speed signal ( BCM
AV
AV - 127
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
PKIA1425J
Caution : Video distributor (rear seat with a voice independent function) is hereinafter referred to as the video distributor.
SKIA2802J
AV - 128
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Antenna path
" Antenna path "( AV-32 page ) reference
JA
AV
AV - 129
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
TKWA0506J
AV - 130
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Terminal sequence
JA
AV
TKWA0507J
AV - 131
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Key switch ACC Or long baseline measurement in the engine stopped state, since this may result in battery depletion, be performed by starting the as possible
engine.
NAVI Control unit input and output signal reference value JKS00CRZ
Terminal
Measurement condition
number Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
Bo
Six Vehicle speed signal ( Two pulse) input ON Vehicle speed about 40km / h Time
de
I|
A|
scan ELF1080D
(one step)
Eight Automatic dimming signal input ON
Light SW ON When it does not shed light
on auto light the light-receiving sensors about 12V
(one step)
SKIA2553J
Concentration SW ( NAVI SW Pressing the)
13
Neu Zureka
SKIA2553J
AV - 132
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Terminal
Measurement condition
number Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
Bo
de
I|
26 A| shield( DVD Video) - ON - about 0V
B
scan
D
SKIA0178J
Bo
de
I| E
A|
Thirty output ON
scan RGB Synchronization signal
SKIA0164J
F
SKIA0166J
29
SKIA0167J
I
Bo
de
I|
33 A| RGB Area signal output ON TV SW Press JA
scan
SKIA0162J
AV
34 29 RGB Signal ( R :Red ) output ON Screen adjustment of the check and adjustment function
And in the color bar display
L
SKIA0165J
AV - 133
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Terminal
Measurement condition
number Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
SKIA0161J
TV SW Press
SKIA0163J
Bo
de about 7V that's all
39 I| Guide voice ON signal output ON Guide at the audio output
Guide voice non-output time about 0V
A|
scan
SKIA0171J
SKIA0171J
AV - 134
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Terminal
Measurement condition
number Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
B
TV / Video audio signal
44 input ON
(left -)
SKIA0177J
SKIA0177J
E
TV / Video audio signal
46 input ON
(left +)
SKIA0177J
F
SKIA2557J
SKIA0177J I
Bo
de
I|
49 A| Shield (microphone) - ON - about 0V
scan JA
88 89 FM Multiple signal - - - -
AV
AV - 135
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Terminal
Measurement condition
number Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
Bo
de
I|
89 Shield (antenna) - ON - about 0V
A|
scan
Bo
de
I|
91 A| shield( GPS ) - ON - about 0V
scan
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
SKIA0175J
Three
SKIA0176J
Bo
de
I|
Three A| Shield (communication) - ON - about 0V
scan
AV - 136
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
B
Four Communication signal (+) Input and output ON -
SKIA0175J
Six
D
SKIA0176J
Bo
de
I|
Six A| Shield (communication) - ON - about 0V
E
scan
G
In front display SKIA0186J
Eleven
TV To receive a broadcast
SKIA0187J
Bo
de I
I|
Eleven A| shield( TV / video) - ON - about 0V
scan
JA
AV
AV - 137
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
SKIA0166J
Bo
de
I|
Fifteen A| RGB Signal Ground - ON - about 0V
scan
SKIA0167J
AV - 138
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
B
17 RGB Area signal output ON
SKIA0162J
A|
scan
SKIA0161J
SKIA0164J G
SKIA0186J
SKIA0187J
JA
Bo
de
dia
twenty four shield( TV / video) - ON - about 0V
|
scan
AV
AV - 139
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
SKIA0166J
Bo
de
dia
27 RGB Signal Ground - ON - about 0V
|
scan
SKIA0167J
31
menu
SKIA0221J
Bo
de
I|
31 A| shield( RGB ) - ON - about 0V
scan
AV - 140
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
B
32 31 RGB Area signal output ON The rear display TV Menu
To view the New
SKIA0162J
D
SKIA0187J
In the rear display TV To receive the
35
transmission release
E
34 TV / Video signal output ON
SKIA0186J
SKIA0220J
The navigation operation in the rear seat Navi
38
remote control
SKIA0219J
JA
41 Earth - ON - about 0V
Bo
43 ACC Power supply input ACC - Voltage power supply
de
44 I| IGN Power supply input ON - Power-supply voltage
AV
A| Open / close of the rear seat Navi remote control about 3.5V Less than ( SW The
scan The rear seat remote control signal (open / closed SW Press moment you press the)
46 input ON
SW )
Other than those above about 5V
47 Earth - ON - about 0V
L
48 BAT Power supply input OFF - Power-supply voltage
AV - 141
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
Bo
de
I|
49 A| shield( DVD Video) - ON - about 0V
scan
SKIA0178J
SKIA0165J
SKIA0166J
SKIA0167J
56
Bo RGB Area signal input ON
de
I|
A| SKIA0162J
SKIA0163J
AV - 142
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
B
58 Vertical synchronization signal input ON TV To view the menu
Bo
de
I| SKIA0161J
A|
scan C
59 RGB Synchronization signal input ON Screen adjustment of the check and adjustment function
And in view of the color bar
D
SKIA0164J
SKIA0177J
G
SKIA0177J
H
65 66 Rear speaker input input ON
(Left rear)
SKIA0177J
JA
SKIA0177J
AV
AV - 143
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
SKIA0165J
SKIA0166J
SKIA0167J
Bo
de
I|
Four A| RGB Signal Ground - ON - about 0V
scan
Bo
13 de Communication signal ( BCM - DP ) Input ON
I|
A|
scan
SKIA2559J
information SW Press
SKIA2566J
AV - 144
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
B
Sixteen Vertical synchronization signal input ON
SKIA0161J
C
Bo
de
I|
17 A| Horizontal synchronization signal input ON TV SW Press
scan
D
SKIA0163J
SKIA0162J
F
SKIA0186J
SKIA0187J I
Bo
de
I| JA
A
twenty four | RGB Synchronization signal input ON Screen diagnosis of check and adjustment function
And in the color bar display
scan
SKIA0164J
AV
Reference: Five , twenty two , twenty three Turn pin function at the time of the back-view camera connection " DI Driver Information System
AV - 145
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Rear display unit input and output signal reference value JKS00BE8
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
One Bo
Earth - ON - about 0V
twenty De
three
I|
A| BAT Power supply input OFF - Power-supply voltage
4
scan
6 ACC Power supply input ACC - Power-supply voltage
control
SKIA0219J
De
I|
A|
14 scan shield( TV / video) - ON - about 0V
SKIA0187J
SKIA0186J
SKIA0162J
AV - 146
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
B
19 Vertical synchronization signal input ON
SKIA0161J
Eighteen TV SW Press
C
D
SKIA0221J
Bo
de
I|
A
twenty one | RGB Signal Ground - ON - about 0V
E
scan
SKIA0167J
G
SKIA0166J
I
twenty four RGB signal( R :Red) input ON
SKIA0165J
JA
AV
AV - 147
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
Bo
de
I| SKIA2553J
Concentration SW ( NAVI SW Pressing the)
A|
Neu Zureka
scan
SKIA2553J
SKIA0186J
SKIA0177J
Twenty
SKIA0177J
SKIA2553J
AV - 148
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
Bo
de
B
14 I| Communication signal (-) Input and output ON Concentration SW ( NAVI SW ) Neu
A| Pressing the Zureka
scan
SKIA2553J
C
Sixteen shield( TV / video) - ON - about 0V
SKIA0187J
F
SKIA0177J
Bo
de
I|
Shield ( TV / Video
Twenty A| - ON - about 0V G
voice)
scan
SKIA0177J
I
De
I|
A|
scan Earth
twenty four - ON - about 0V JA
AV
SKIA0188J
L
AV - 149
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- Operation or state
SW
Bo
de
I|
26 A| Shield (video) - ON - about 0V
scan
SKIA0188J
Bo
de
I|
28 A| Video audio signal ground - ON - about 0V
scan
SKIA0189J
SKIA0189J
AV - 150
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- operation
SW
TEL ON
B
(Press state): about 0V
Voice commands ON
2 22 Control signal B output ON TEL , Voice command, (Press state): about 1.7V VOL ( DOWN
VOL ( DOWN )Press
) ON
(Press state): about 3.3V C
the above SW OFF :about 5V
(one step)
14 Automatic dimming signal output ON D
Light SW ON When it does not shed light
on auto light the light-receiving sensors about 12V
(one step)
Bo E
de
Fifteen I| Communication signal ( SW - BCM ) Input ON Concentration SW ( NAVI SW ) Neu
Pressing the Zureka
A|
scan
SKIA2946J F
SKIA2559J
I
SKIA2553J
MODE ON
(Press state): about 0V
CH ( UP ) ON
21 22 Control signal A output ON MODE , CH ( UP ), VOL (Press state): about 1.7V VOL ( UP JA
( UP )Press
) ON
(Press state): about 3.3V
Bo AV
de
I|
A
twenty two | Control signal ground - ON - about 0V
scan
AV - 151
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Measuring
Measurement condition
terminal Input and
Signal name Reference value
output of the signal
Key
+- operation
SW
A|
scan
SKIA2566J
SKIA2553J
Bo
de
I|
Forty A| Shield (communication) - ON - about 0V
scan
TEL ON
(Press state): about 0V
Voice commands ON
Steering wheel (Press state): about 1.7V VOL ( DOWN
Fifty input ON TEL , Voice command,
SW signal B VOL ( DOWN )Press
) ON
(Press state): about 3.3V
CH ( UP ) ON
Steering wheel (Press state): about 1.7V VOL ( UP
61 input ON MODE , CH ( UP ), VOL
SW signal A ( UP )Press
) ON
(Press state): about 3.3V
Bo
de
I|
Steering wheel
62 A| - ON - about 0V
SW Signal Ground
scan
Reference: Eighteen , 39 , 70 Ban terminal beacon unit, ETC Function at the time of unit connection.
AV - 152
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
2. To grasp the system overview. " System Overview "( AV-119 page ) See.
3. Not unusual phenomenon example "There is no abnormal phenomenon Example" ( AV-107 page ) A phenomenon that corresponds to confirm it is in.
Four. Carry out the power supply and ground circuit inspection of the relevant unit as a diagnostic before inspection. " NAVI Power supply and the ground control unit B
Circuit inspection "( AV-167 page ) , " Power supply and ground circuit inspection of the video distributor "( AV-168 page ) , " Power supply and ground circuit inspection of the
front display Lee unit "( AV-169 page ) , " The power supply and the ground circuit inspections of the rear display unit "( AV-170 page ) , " TV Inspection of the tuner power supply
C
Five. It performs a failure diagnosis from each phenomenon, to identify the cause.
6. Before you replace the failed components were determined to be defective in the diagnosis, make a connection confirmation of the connector again.
D
8. Or failure of the system to operate properly? In the case of normal Nine What. If abnormalities Five What.
9. Exit.
Overview
• A self-diagnostic mode (excluding the back view monitor) for self-diagnosis function to independently activated from each system, the self-diagnosis menu which can
perform self-diagnosis together several system Two There is a kind.
• Self-diagnosis menu is possible to display the screen switch of each system to the front display, it can be called a self-diagnostic mode you need at the F
touch of a button.
Operation procedure
starting method G
Five. Air conditioning OFF Press the switch, to stop the air conditioning.
I
6. While holding down the information switch, temperature control dial (right) Ten Within seconds
SKIA2767J
To Thirty Click to manipulate or more. Reference: The direction of rotation of the temperature control dial (right)
How to undo
AV - 153
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Menu item
The communication diagnosis by transmission and reception of data on the network do. Detail is "Communication Diagnostics "
system
(BCS-34 page ) See.
Air conditioning Perform self-diagnosis of air conditioning. Detail is "Self-diagnosis function" ( ATC-19 page ) See.
A change in the state of each switch is detected by the data on the network. Detail is "Switch Monitor" ( BCS-39
switch
page ) See.
• Color bar color shade confirmation of by the color of the confirmation and gray scale display by the display.
monitor
• It is back view video display car width and distance of the guide line correction of the time. Detail is "Self-diagnosis
menu" ( DI-44 page ) See.
• Lighting of the auto light, can adjust the sensitivity of the off.
Vehicle setting
• To set the timer operating time of the rear defogger.
NAVI Perform self-diagnosis of navigation. Detail is "Fault diagnosis function" ( AV-59 page ) See.
Overview
• Fault diagnosis function, it is automatically and self-diagnostic mode that diagnosis is made, check and adjustment mode to operate manually.
• Self-diagnostic mode, the connection confirmation and individual unit diagnosis between the units that make up the system collectively performed to display the results in the liquid crystal display.
• Check and adjustment mode, it requires a decision and a human operator (can not be automatic judgment of the system side) fault diagnosis, to display the error history of the check and change
Operation procedure
2. "Map / PLAY "Switch and the" image quality "switch at the same time Five Press sec or more.
SKIA2567J
Four. " self-diagnosis "," Error history "," Check and adjustment "and" voice guide confirmation
SKIA2568J
AV - 154
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Diagnostic items
• C / U Diagnosis of (map DVD-ROM Not inserted at the time of DVD-ROM Driver units diagnosis of is not
performed)
self-diagnosis
• C / U ~ GPS Connection diagnosis between the antennas, C / U - Make a diagnosis of the connection diagnostic and
To view the problems and the number of occurrences of occurred in the past was Navi relationship. In addition, to display
B
Error history
the last time and place that occurred When you select a defect item.
Confirmation of color by color bar display, and Shades of colors by gray scale display can be
Screen Adjustment
confirmed.
Vehicle speed, parking brake, light, IGN (Key SW ), Can each signal diagnosis of the reverse.
Vehicle signal C
Navigation adjustment When deviation occurs in the angle angle and car mark angle adjustment wheel bends actually bends
It can be adjusted.
It can be adjusted when the deviation between the actual position and distance adjustment current position mark has occurred.
DVD-ROM driver, DVD-ROM To display the version of the software and the unit, such as
Version Display
a.
Error history, error history erase, ETC Ru can erase unit of the connection history. E
ETC unit
DVD Erase the personal identification number at the time of parental level set in the video playback.
DVD Personal identification number erase
Audio guide confirmation To output the sound from the audio guide for the speakers.
F
Operation procedure G
• Bar graph of the lower side of the screen in the self-diagnosis in the screen displays the rate of progress of
H
the diagnosis.
ELK1432D
2. When the self-diagnosis is completed, the display unit connection confirmation screen.
JA
• If the terms of optional accessories it is determined that the abnormal connection, the relevant parts to
display from either confirmation screen is attached to the actual. If you are attached to select the screen
• In the case of optional accessories connection is normal, appropriate screen switch is not displayed. AV
SKIA2569J
AV - 155
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
3. The screen switch of the diagnostic result screen unit name, depending on the diagnosis result
Caution : MET & A / C ECU In the text in the BCM It has been referred to as.
• For one unit, screen switch the color of the scene in which a plurality of error has occurred at the same
SKIA2804J
• Control unit and MET & A / C ECU , Video distribution machines, TV tuner, GPS Between the antenna is connected by a green or yellow depending on the diagnosis.
• Between the units other than the above are connected by a green or gray depending on the diagnostic results.
Four. Diagnosis result of comments table and choose a screen switch of diagnostic results in the screen
Shown.
• In the case of the green comment " Self-diagnosis is normal. Detailed diagnostics and adjustments are not
made to diagnose according to the "check and adjustment" mode and maintenance manual " To display.
• In the case of the yellow comment "it is abnormal connection with the following unit. Please diagnosed
• In the case of the red comment will be displayed as "XX unit is abnormal".
• In the case of ash comment " DVD-ROM Because it has not yet been inserted, the control unit ELK1435D
of DVD-ROM To display the diagnosis has not been made "of the driver.
1. To select the diagnostic corresponding number from the diagnostic results Chart.
2. Carry out the inspection of each system from diagnosis number table.
Screen switch
○ Diagnosis Two
○ Diagnosis Four
○ Diagnosis Five
○ Diagnosis Six
○ Diagnosis Eight
○ ○ Diagnosis Nine
Caution : Representation of the screen switch has been described as following in the sentence.
AV - 156
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Diagnosis Two NAVI C / U There map DVD - ROM It is determined that is not inserted (AV-157)
Diagnosis Three Front display unit diagnosis is not yet implemented (AV-157)
C
Diagnosis Four Rear display unit diagnosis is not yet implemented (AV-159)
" DVD - ROM It is abnormal. Please check the disk. Comments of "has been displayed. NAVI C / U There, the map
that has been inserted DVD - ROM It was recognized as abnormal. It should be noted that the map DVD - ROM Abnormality,
Diagnosis Five (AV-160)
or NAVI C / U Failure of is considered.
D
" DVD - ROM Or NAVI Inside DVD - ROM Driver is abnormal. Please therefore to diagnose the maintenance
manual. Comments of "is displayed. map DVD - ROM Not read the data. It should be noted that the map DVD -
Diagnosis Six (AV-160)
ROM Driver abnormalities it is considered.
Diagnosis Eight Power and ground lines of the video distributor (AV-168)
Diagnosis Nine GPS Antenna and NAVI C / U It is but abnormal connection (AV-161)
NAVI Control unit map DVD - ROM When it is determined that is not inserted JKS00CMW
F
OK » NAVI C / U Failure
H
When the front display unit diagnosis has not yet been implemented JKS00CMX
To check the power supply system of the front display unit. " The power supply and the ground circuit inspections of the front display unit "( AV-169 page ) See. I
OK » Two What
BCM Perform self-diagnosis (communication inspection). " BCS Body Control System " " Communications Diagnostics " (BCS-34 page ) See.
AV
Failure code 34 Or There has been displayed?
AV - 157
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Spray unit vehicle-side harness connector 13 , Fifteen To check the conduction of turn terminal.
4. BCM Vehicle side harness connector Sixteen , 37 Ban terminal ~ Body Architect
OK » Four What
3. Press the information switch, BCM Of the vehicle-side harness connector Sixteen , 37
Measuring terminal
Measurement condition Reference value
(+) (-)
Sixteen
SKIA2620J
37
SKIA2566J
NG » • Constant voltage value (about 5V Replace the front display unit if in the vicinity of) the voltage waveform does not appear
• Constant voltage value (about 0V If the voltage waveform does not appear in the vicinity) is BCM To replace the
AV - 158
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
When the rear display unit diagnosis has not yet been implemented JKS00CMY
To check the power supply system of the rear display unit. " Power supply and ground circuit inspection of the rear display unit " (AV-170
page ) See.
OK » Two What
2. Video distributor ( TH Type Sixteen Remove the connector of the pole) and the rear display unit.
3. Video distributor vehicle side harness connector 38 , 39 , Forty Ban terminal - rear D
Display unit vehicle-side harness connector Eight , Nine , Ten Check the continuity of turn
jacks.
G
Inspection results OK Or?
OK » Three What
NG »Repair the video distributor - rear display unit between the harness
JA
AV
AV - 159
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. To connect the connector of the video distributor and rear display unit.
2. The key switch ON And, of the video distributor vehicle side harness connector
39 , Forty Ban terminal ~ 38 To check the voltage waveform between the turn terminal.
terminal
Measurement condition Reference value
(+) (-)
39
SKIA2664J
down
Forty
SKIA0219J
NG » • Constant voltage value (about 5V Replace the rear display unit if in the vicinity of) the voltage waveform does not appear
• Constant voltage value (about 0V To replace the video distributor If the in the vicinity of) the voltage waveform does not appear
NAVI Map the control unit is inserted DVD - ROM Or map when it is determined that the is abnormal DVD - ROM When
you do not read the data from JKS00CMZ
OK » Two What
OK » Three What
AV - 160
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
NAVI Control unit and GPS When the connection of the antenna is abnormal JKS00CN0
OK » Two What
Other normal GPS Replace the antenna to perform the self-diagnosis again. E
F
Error history mode JKS00C3Z
Operation procedure
SKIA2568J
JA
AV
AV - 161
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
ELK1444D
Diagnostic results at the time of the "self-diagnosis", key SW The ON It is judged by whether or not an error has occurred and from the to the end "self-diagnosis". On the other hand, key SW
The ON Previous error occurs that, if not occur until the "self-diagnosis", the diagnostic results Ru is determined to be normal. Therefore, the error that occurred in the past can not be
determined in the "Diagnostic" point, it is necessary to make a diagnosis from the "error history".
In the error history, but to display the time and place where the error last occurred to note the following.
• NAVI In the control unit of GPS If the substrate is abnormal, it may not be possible to display the correct time of occurrence.
• Generating location, since the error is the current position mark display position when generated, if has been out of the time mark the correct position, it may not be
possible to display the correct position.
• Maximum number of occurrences Fifty Although stored until times, 51 More than once Fifty It is displayed times.
But reproducible failure has occurred, if isolate the cause of the problem have more than one error is displayed is difficult, after having declined to items and times the number and location
(latitude and longitude) (or the error history in erasing), the once key switch OFF From ON In, and failure to verify again error history from to reproduce, to diagnose the center the items that
Probable cause
Error item Failure phenomenon example
Deal content or content of trouble
abnormal
• Portrayal of the front and rear display does
sub CPU Abnormal connection • To implement the self-diagnostic mode
not appear
• In self-diagnosis NAVI C / U It is considered a temporary abnormality due to
• Carry out the inspection of the vehicle speed signal • Can not navigate the position detection performance
Vehicle speed sensor connection error
" Vehicle speed signal inspection "( AV-172 page ) Reference to the (can not move distance detection)
NAVI C / U With the interior of the GPS Communication with the Board error
• Navigation position detection performance is degraded ( GPS Position
GPS disconnected
• To implement the self-diagnostic mode
correction by is not performed)
• In self-diagnosis NAVI C / U It is considered a temporary abnormality due to
• GPS While the state of the reception of gray
interference of strength if there is normal
AV - 162
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Probable cause
Error item Failure phenomenon example
Deal content or content of trouble
GPS ROM Abnormality GPS Because it is not possible to correct positioning by, the
NAVI C / U When GPS Substrate and GPS Contact with the antenna connection
is abnormal
• Navigation position detection performance is degraded ( GPS Position
NAVI C / U With the interior of the DVD - ROM Communication error with the driver
NAVI C / U Internal and DVD VIDEO Communication error with the module
DVD VIDEO
• To implement the self-diagnostic mode • DVD VIDEO There can not be played G
Module abnormal
• In self-diagnosis NAVI C / U It is considered a temporary abnormality due to
I
TV Tuner connection anomaly • TV Failure of the tuner • TV It does not appear in the video
AV - 163
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Operation procedure
1. Of fault diagnosis initial screen " Check and adjustment " To select.
2. By selecting each screen switch of check and adjust the screen, call each diagnosis
Fine out, "Back" Become a check and adjust the initial screen and press the switch.
SKIA2568J
SKIA3018J
Screen Adjustment
SKIA3033J
• RGB In the case of signal failure of the system, color bar display of color is as follows.
• If the shade is funny is, " Front, rear display both RGB It is funny shade of the screen " (AV-193 page ) , Front display only if shade is funny "Front
display only RGB Tint of the screen is wrong. "( AV196 page ) , If the tint only rear display is funny "Rear display only RGB Tint of the screen is not
funny "( AV-198 page ) See you confirm that you have read.
AV - 164
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
• It is the actual comparison confirmation of the signal that is recognized by the state and the system side of each
vehicle signal.
SKIA3034J
ON Light SW ON Time Written by the brightness of the outside of the vehicle SW There is if you do not
E
Light
OFF Light SW OFF Time want to work in (automatic dimming function)
ON Key SW ON Time
IGN -
OFF Key SW ACC Or OFF Time
F
ON Select lever R Switching of the range at the time the display is about 1.5 Delayed about seconds Kotogaa
• The vehicle speed is NG In the case of "Vehicle speed signal inspection" ( AV-172 page ) See you confirm that you have read. G
• Parking brake NG In the case of "Parking brake signal inspection" ( AV-173 page ) See you confirm that you have read.
• Lights NG In the case of "Front, not light down rear display both automatic" ( AV-207 page ) See you confirm that you have read.
• IGN But NG In the case of " IGN Signal inspection "( AV-173 page ) See you confirm that you have read.
H
• Reverse is NG In the case of "Reverse signal inspection" ( AV-174 page ) See you confirm that you have read.
Navigation adjustment
Angle adjustment
I
• It is possible to adjust the output value of the rotation angle detected by the gyro.
JA
AV
ELK1442D
AV - 165
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Distance adjustment
• Usually, to automatically adjust the distance error due to the variation of wear and air pressure of the tire by the
automatic distance correction function, such as if you are traveling by mounting a tie or a chain, carried out when
ELK1443D
Hands-free volume control To adjust the earpiece volume during hands-free calls.
Communication modem ID Confirmation To check the serial number of the communication modem.
Hands-free phone memory (redial, outgoing, incoming, such as the registration number) is erased.
Memory erasing
Information Center phone number registration To display the phone number of each information center, it is the telephone number registration.
• The voice that was speaking into the microphone can be output from the front speakers (left side).
Confirmation Microphone Speaker • Decision SW When you press, from the front speakers (left) MUTE And outputs the sound. In addition, at that
time an electronic tuner radio " MUTE " Character is displayed.
Version Display
• DVD - ROM driver, DVD - ROM To display the version of the software and the unit, such as a.
ETC unit
ETC Error history of the unit, erase the error history, ETC It can erase unit of the connection history.
DVD It is possible to erase the personal identification number at the time of parental level set in the video playback.
Operation procedure
2. Select the decision switch (press) S for voice guide the confirmation sound by
SKIA2568J
AV - 166
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
NAVI Power supply and ground circuit inspection of the control unit JKS00CSA
1. Fuse inspection
NAVI Or to check there is no blow to the following fuse of the control unit.
C
Inspection results OK Or?
OK » Two What
NG »If the fuse had blown, replace from to repair the cause of the blow to the new fuse
D
2. Power circuit inspection
NAVI control unit( TH Type Twelve Remove the connector of the pole), the terminal number of the
vehicle-side harness connector of the under-mentioned table (+), the body grounding (- measured as).
SKIA2593J
Inspection results OK Or?
OK » Three What
G
NG » NAVI To repair the control unit power supply circuit harness
OK »Normal
AV
AV - 167
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Power supply and ground circuit inspection of the video distributor JKS00BJ9
1. Fuse inspection
To check whether there is a blow below the fuse of the video distributor.
OK » Two What
NG »If the fuse had blown, replace from to repair the cause of the blow to the new fuse
Video distributor ( TH Type Eight Remove the connector of the pole), the terminal number of the
vehicle-side harness connector of the table below (+), the body earth (- measured as).
SKIA2665J
Inspection results OK Or?
OK » Three What
Check for continuity between the following vehicle side harness connector - body earth of the video
distributor.
OK »Normal
AV - 168
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Power supply and ground circuit inspection of the front display unit JKS00CSB
1. Fuse inspection
Blow below the fuse of the front display unit is to check whether or not there.
NG »If the fuse had blown, replace from to repair the cause of the blow to the new fuse
Remove the connector of the front display unit, the terminal number of the vehicle-side
harness connector of the table below (+), the body earth - is measured as ().
E
Terminal number Signal name Key SW Reference value
SKIA2595J
OK » Three What
G
3. Ground circuit inspection
Check for continuity between the following vehicle side harness connector - body earth
of the front display unit.
H
Terminal number Signal name Key SW Conduction
OK »Normal
I
JA
AV
AV - 169
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Power supply and ground circuit inspection of the rear display unit JKS00BJA
1. Fuse inspection
Or to check there is no blow to the following fuse of the rear display unit.
OK » Two What
NG »If the fuse had blown, replace from to repair the cause of the blow to the new fuse
Remove the connector of the rear display unit, the terminal number of the vehicle-side
harness connector of the table below (+), the body earth - to measure and to ().
SKIA2668J
OK » Three What
NG »To repair the rear display unit power supply circuit harness
Check for continuity between the following vehicle side harness connector ~ Bo Dee ground of
the rear display unit.
OK »Normal
AV - 170
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. Fuse inspection
TV Blow below the fuse of the tuner is to check whether or not there.
NG »If the fuse had blown, replace from to repair the cause of the blow to the new fuse
TV tuner( TK Type twenty four Remove the connector of the pole), the terminal number of the
vehicle-side harness connector of the table below (+), the body earth (- to measure) and to.
E
Terminal number Signal name Key SW Reference value
F
Inspection results OK Or?
SKIA2597J
OK » Three What
G
3. Ground circuit inspection
TV Check for continuity between the following vehicle side harness connector - body earth of the
tuner.
H
Terminal number Signal name Key SW Conduction
JA
AV
AV - 171
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
NO »Carry out the inspection of the vehicle speed input signal. " DI Driver Information System " "How to proceed with fault diagnosis "
2. Harness inspection
2. NAVI control unit( TH Type Twelve Remove the connector of the pole) and combination meter.
- Combination meter vehicle side harness connector 39 To check the continuity between the turn
end child.
SKIA2600J
OK » Three What
NG » NAVI To repair the harness between the control unit - Combination meter
2. Allowed to run the car, NAVI Control unit vehicle-side harness connector
Compactors Six To check the voltage waveform between the turn pin-body earth.
Measuring terminal
Measurement condition Reference value
(+) (-)
ELF1080D
NG » • Constant voltage value (about 5V If the voltage waveform does not appear in the vicinity) to replace the combination meter
• Constant voltage value (about 0V If the voltage waveform does not appear in the vicinity) is NAVI To replace the control unit
AV - 172
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
2. Carry out the inspection of the brake warning light in the combination meter inside stepping on the parking brake.
Step on the parking brake / have line the release operation of the parking brake, NAVI Control
unit vehicle-side harness connector Three To check the voltage between the turn pin-body
earth.
D
NG » NAVI To repair the control unit - the parking brake switch between the harness
2. NAVI control unit( TH Type Twelve Remove the connector of the pole). H
3. And the key switch to the following measurement conditions, NAVI Control Unit
To vehicle side harness connector Five To check the voltage between the turn pin-body earth.
I
Measuring terminal
Measurement condition Reference value
(+) (-)
OFF about 0V
Body earth
Five Key SW ACC about 0V JA
ON Power-supply voltage SKIA3053J
AV - 173
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
2. The shift position R The range, to inspect the shift position indicator on the combination meter inside.
By operating the select lever, NAVI Control unit vehicle-side harness connector Four To
switch
Measurement condition Reference value
(+) (-)
1. BCM Self-diagnosis (communication diagnosis) inspection One ( BCM ~ NAVI control unit)
BCM Perform self-diagnosis (communication diagnosis). " BCS Body Control System " " Communications Diagnostics " (BCS-34 page ) See.
NO » Two What
NO » Three What
Centralized switch ( NAVI Switch) of " map/ PLAY " Switch and " image quality " If the switch is working properly?
AV - 174
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
3. BCM Vehicle side harness connector Fifteen , 35 Ban terminal ~ centralized switch
Vehicle side harness connector Twelve , Six To check the continuity between the turn terminal.
B
4. BCM Vehicle side harness connector Fifteen , 35 Ban terminal ~ Body Architect
C
To check the continuity between the vinegar.
D
Inspection results OK Or?
OK » Five What
E
Five. Centralized switch signal inspection
connector Fifteen , 35 To check the voltage waveform between the turn pin-body earth.
Measuring terminal G
Measurement condition Reference value
(+) (-)
H
SKIA3031J
Fifteen
Concentration SW ( NAVI
Body earth SKIA2946J
SW Press any) I
35
JA
SKIA2947J
NG » • Constant voltage value (about 5V If in the vicinity of) the voltage waveform does not appear to replace the centralized switch
• Constant voltage value (about 0V If the voltage waveform does not appear in the vicinity) is BCM To replace the
AV - 175
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
2. BCM as well as TV tuner( TK Type twenty four Remove the connector of the pole).
Vehicle side harness connector 14 , Two To check the continuity between the turn terminal.
19 ~ 14 : Yes conduction
OK » Seven What
2. Vehicle side harness connector of the video distributor Four , Five Ban terminal ~ TV Chu
Donor vehicle side harness connector of Twelve , One To check the continuity between the turn terminal.
3. Vehicle side harness connector of the video distributor Four , Five Ban terminal ~ Body
OK » Eight What
AV - 176
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
C
3. NAVI Control unit vehicle-side harness connector 13 , 14 ,
Sixteen To check the continuity between the turn pin-body earth. SKIA2673J
OK » Nine What
E
NG »Video distributor - NAVI To repair the control unit between the harness
1. BCM , TV Tuner, video distributor and NAVI To connect the connector of the control unit. F
3. Centralized switch ( NAVI Operating the switch), the video distributor vehicle side hard
Ness connector One , Two Ban terminal ~ Three To check the voltage waveform between the turn terminal.
Measuring terminal
Measurement condition Reference value
(+) (-)
One
Concentration SW ( NAVI
Three SW Press any)
Two SKIA3028J
SKIA2553J
I
OK » Ten What
AV
AV - 177
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Centralized switch ( NAVI Operating the switch), TV Tuner vehicle side harness connector One , Twelve
Measuring terminal
Measurement condition Reference value
(+) (-)
One
Concentration SW ( NAVI
Body earth SKIA3022J
SW Press any)
Twelve
SKIA2553J
OK » Eleven What
Centralized switch ( NAVI Operating the switch), BCM Vehicle side Hanesuko nectar 19 , 38 Ban terminal ~ Forty To
Measuring terminal
Measurement condition Reference value
(+) (-)
19
Concentration SW ( NAVI
Forty SW Press any)
38 SKIA3030J
SKIA2553J
It does not appear at all screen only the front display (navigation, TV , Except for the video screen) JKS00BJE
2. Centralized switch ( NAVI Pressing the image quality switches of the switch).
AV - 178
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
BCM Perform self-diagnosis (communication diagnosis). " BCS Body Control System " " Communications Diagnostics " (BCS-34 page ) See.
3. Harness inspection
Spray unit vehicle-side harness connector 13 , Fifteen To check the conduction of turn terminal.
D
Sixteen ~ 13 : Yes conduction
4. BCM Vehicle side harness connector Sixteen , 37 Ban terminal ~ Body Architect
E
To check the continuity between the vinegar.
OK » Four What
JA
AV
AV - 179
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
3. information SW Press, BCM Vehicle side harness connector Sixteen , 37 Turn end
Sixteen body
Earth SKIA2620J
SKIA2559J
information SW Press
37 body
Earth
SKIA2566J
NG » • Constant voltage value (about 5V Replace the front display unit if in the vicinity of) the voltage waveform does not appear
• Constant voltage value (about 0V If the voltage waveform does not appear in the vicinity) is BCM To replace the
1. Self-diagnosis inspection
Perform a self-diagnostic mode. " Self-diagnostic mode "( AV-155 page ) See.
Caution : If the failure diagnosis screen does not start, " Failure diagnosis screen does not start "( AV-174 page ) To implement.
NO » " When the rear display unit diagnosis has not yet been implemented "( AV-159 page ) To implement the measurement terminal
AV - 180
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
2. Harness inspection
2. Video distributor ( TH Type Sixteen Remove the connector of the pole) and the rear display unit.
Ray unit vehicle-side harness connector Twelve To point detects the conduction between the turn terminal.
B
Four. Video distributor vehicle side harness connector 36 Ban terminal ~ Body Architect
C
To check the continuity between the vinegar.
SKIA2917J
NG »To replace the video distributor - rear display unit between the harness
1. To connect the connector of the video distributor and rear display unit.
2. Video distributor vehicle side harness connector 36 Ban terminal ~ Body Architect
F
36 ~ Body earth :about 5V that's all
SKIA2918J
JA
AV
AV - 181
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. Harness inspection
2. Video distributor ( TH Type Twelve Pole) and NAVI control unit( TH Type Forty Remove the connector of the pole).
3. Video distributor vehicle side harness connector 49 , Fifty Ban terminal ~ NAVI Co
Control Unit vehicle side harness connector 26 , 28 To check the continuity between the turn
terminal.
49 ~ 26 : Yes conduction
Four. Video distributor vehicle side harness connector 49 , Fifty Ban terminal ~ Body
Inspection results OK Or
OK » Two What
NG »Video distributor - NAVI To repair the control unit between the harness
1. Video distributor and NAVI To connect the connector of the control unit.
4. DVD Play the video, the video distributor vehicle side harness connector Fifty
Ban terminal ~ 49 To check the voltage waveform between the turn terminal.
Measuring terminal
Measurement condition Reference value
(+) (-)
SKIA0178J
Inspection results OK Or
" Front display only TV , Not out video "( AV-184 page ) See.
" Rear display only TV , Not out video "( AV-185 page ) See.
AV - 182
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Front, rear display both TV ,video( DVD Except for the video) does not appear the video JKS00BJH
1. Harness inspection
2. Video distributor ( TH Type twenty four Pole) and TV tuner( TK Type twenty four Remove the connector of the pole).
3. Video distributor vehicle side harness connector twenty two , twenty four Ban terminal ~ TV Chu
B
Donor vehicle side harness connector Five , Sixteen You check the continuity between the turn terminal.
Four. Video distributor vehicle side harness connector twenty two , twenty four Ban terminal ~ Body
SKIA2921J D
twenty two ~ Body earth : No conduction
Inspection results OK Or
OK » Two What E
3. TV Receiving the broadcast, the video distributor vehicle side harness connector twenty two Turn
Terminal ~ twenty four To check the voltage waveform between the turn terminal. G
Measuring terminal
Measurement condition Reference value
(+) (-)
I
SKIA0186J
Inspection results OK Or
AV
AV - 183
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. Harness inspection
2. Video distributor ( TH Type twenty four Remove the connector of the pole) and the front display unit.
3. Video distributor vehicle side harness connector Nine , Eleven Ban terminal ~ Front
Display vehicle side harness connector 19 , twenty one To check the continuity between the turn terminal.
Four. Video distributor vehicle side harness connector Nine , Eleven Ban terminal ~ Body
Inspection results OK Or
OK » Two What
NG »Repair the video distributor - the front display unit between the harness
3. TV Receiving the broadcast, the video distributor vehicle side harness connector Nine Turn end
Child ~ Eleven To check the voltage waveform between the turn terminal.
Measuring terminal
Measurement condition Reference value
(+) (-)
SKIA0186J
Inspection results OK Or
AV - 184
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. Harness inspection
2. Video distributor ( TH Type Sixteen Remove the connector of the pole) and the rear display unit.
Spray vehicle side harness connector Sixteen , 14 To point detects the conduction between the turn terminal.
Four. Video distributor vehicle side harness connector 34 , 35 Ban terminal ~ Body
D
34 ~ Body earth : No conduction
SKIA2685J
Inspection results OK Or
OK » Two What E
NG »Repair the video distributor - rear display unit between the harness
3. TV Receiving the broadcast, the video distributor vehicle side harness connector 34 Turn
Measuring terminal
Measurement condition Reference value
(+) (-)
I
SKIA0186J
Inspection results OK Or
AV
AV - 185
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
Front, rear display both TV ,video( DVD Except for the video) flowing video JKS00BJP
1. Harness inspection
2. Video distributor ( TH Type twenty four Pole) and TV tuner( TK Type twenty four Remove the connector of the pole).
3. Video distributor vehicle side harness connector twenty three , twenty four Ban terminal ~ TV Chu
Donor vehicle side harness connector 17 , Sixteen You check the continuity between the turn terminal.
Four. Video distributor vehicle side harness connector twenty three , twenty four Ban terminal ~ Body
SKIA2698J
twenty three ~ Body earth : No conduction
Inspection results OK Or
OK » Two What
3. TV Receiving the broadcast, the video distributor vehicle side harness connector twenty three Turn
Terminal ~ twenty four To check the voltage waveform between the turn terminal.
Measuring terminal
Measurement condition Reference value
(+) (-)
SKIA0187J
Inspection results OK Or
AV - 186
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. Harness inspection
2. Video distributor ( TH Type twenty four Remove the connector of the pole) and the front display unit.
3. Video distributor vehicle side harness connector Ten , Eleven Ban terminal ~ Front
B
Display vehicle side harness connector Twenty , twenty one To check the continuity between the turn terminal.
Four. Video distributor vehicle side harness connector Ten , Eleven Ban terminal ~ Body
D
Ten ~ Body earth : No conduction
SKIA2701J
Inspection results OK Or
OK » Two What E
NG »Repair the video distributor - the front display unit between the harness
3. TV Receiving the broadcast, the video distributor vehicle side harness connector Ten Turn
Terminal ~ Eleven To check the voltage waveform between the turn terminal.
G
Measuring terminal
Measurement condition Reference value
(+) (-)
I
SKIA0187J
Inspection results OK Or
AV
AV - 187
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. Harness inspection
2. Video distributor ( TH Type Sixteen Remove the connector of the pole) and the rear display unit.
Spray vehicle side harness connector Fifteen , 14 To point detects the conduction between the turn terminal.
35 ~ 14 : Yes conduction
Four. Video distributor vehicle side harness connector 33 , 35 Ban terminal ~ Body
Inspection results OK Or
OK » Two What
NG »Repair the video distributor - rear display unit between the harness
1. To connect the connector of the video distributor and rear display unit.
3. TV Receiving the broadcast, the video distributor vehicle side harness connector 33 Turn
Measuring terminal
Measurement condition Reference value
(+) (-)
SKIA0187J
Inspection results OK Or
AV - 188
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. Harness inspection
2. NAVI control unit( TH Type Forty Pole) and the video distributor ( TH Type Twelve Remove the connector of the pole).
Terminal-video distributor vehicle side harness connector 56 , 57 To check the continuity between the turn
terminal.
33 ~ 56 : Yes conduction
C
36 ~ 57 : Yes conduction
D
33 ~ Body earth : No conduction
SKIA2691J
Inspection results OK Or
OK » Two What E
NG » NAVI To repair the harness between the control unit - the video distributor
Measuring terminal
Measurement condition Reference value
(+) (-)
H
SKIA2692J
36 body
Earth TV SW Press
I
SKIA0163J
Inspection results OK Or
JA
OK » Three What
AV
AV - 189
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
procedure Two Under the same conditions as, NAVI Control unit vehicle-side Hanesuko nectar 33 To
33 body
Earth TV SW Press SKIA2693J
SKIA0162J
Inspection results OK Or
1. Harness inspection
2. Video distributor ( TH Type twenty four Remove the connector of the pole) and the front display unit.
3. Video distributor vehicle side harness connector 17 , Eighteen Ban terminal ~ Front
Display unit vehicle-side harness connector Eighteen , 17 Between the turn terminal Check the
continuity of.
SKIA2694J
17 ~ Body earth : No conduction
Inspection results OK Or
OK » Two What
NG »Measuring terminal to repair the video distributor - the front display unit between the harness
AV - 190
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. To connect the connector of the video distributor and the front display unit.
3. TV SW Press to TV To display the menu, the video distributor vehicle side hard
Ness connector Eighteen To check the voltage waveform between the turn pin-body earth.
B
distributor
Measurement condition Reference value
(+) (-)
C
SKIA2924J
Eighteen body
Earth TV SW Press
D
SKIA0163J
Inspection results OK Or
OK » Three What E
Measuring terminal
Measurement condition Reference value G
(+) (-)
17 body H
Earth TV SW Press SKIA2925J
SKIA0162J
Inspection results OK Or
I
JA
AV
AV - 191
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. Harness inspection
2. Video distributor ( TH Type Sixteen Remove the connector of the pole) and the rear display unit.
3. Video distributor vehicle side harness connector Thirty , 31 , 32 Ban terminal - rear
Display unit vehicle-side harness connector Twenty , Eighteen , 17 Between the turn terminal Check the
continuity of.
32 ~ 17 : Yes conduction
Inspection results OK Or
OK » Two What
NG »Repair the video distributor - rear display unit between the harness
1. To connect the connector of the video distributor and rear display unit.
3. TV SW Press to TV To display the menu, the video distributor vehicle side hard
Ness connector Thirty Ban terminal ~ 31 To check the voltage waveform between the turn terminal.
Measuring terminal
Measurement condition Reference value
(+) (-)
Thirty 31 TV SW Press
SKIA2696J
SKIA0221J
Inspection results OK Or
OK » Three What
AV - 192
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
procedure Two Under the same conditions as, the video distributor vehicle side harness connector 32 Turn end
Measuring terminal
Measurement condition Reference value
(+) (-) B
32 31 TV SW Press
C
SKIA2697J
SKIA0162J
Inspection results OK Or D
Front, rear display both RGB It is funny shade of the screen JKS00BEE
E
NG » Two What
G
JA
AV
AV - 193
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
2. Harness inspection
2. Video distributor ( TH Type Twelve Pole) and NAVI control unit( TH Type Forty Remove the connector of the pole).
3. Following terminal of the video distributor vehicle side harness connector ~ NAVI Comte
To check the continuity between the following terminals of the roll unit vehicle-side harness connector.
Four. Following terminal ~ body of the video distributor vehicle side harness connector
phenomenon)
Inspection results OK Or
OK » Three What
NG »Video distributor - NAVI To repair the control unit between the harness
AV - 194
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. Video distributor and NAVI To connect the connector of the control unit.
3. "Screen adjustment" of the check and adjustment mode To display the color bar at. " Confirmation - Adjustment mode "( AV-164 page ) See.
Four. Voltage waveform between the following terminals of the video distributor vehicle side harness connector
B
To inspect the.
C
Measuring terminal
Measurement condition Reference value
(+) (-)
D
To display a color bar on the
SKIA0165J
E
Measuring terminal
Measurement condition Reference value
(+) (-) F
SKIA0166J
Measuring terminal
SKIA2926J
Measurement condition Reference value
(+) (-)
JA
SKIA0167J
Inspection results OK Or
AV - 195
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
2. Of check and adjustment mode " Screen Adjustment " To check the color at. " Screen "( AV-164 page ) See.
NG » Two What
2. Harness inspection
2. Video distributor ( TH Type twenty four Remove the connector of the pole) and the front display unit.
3. Following terminal-front display unit vehicle-side harness connector of the video distributor vehicle side harness connector
To check the continuity between the following terminals.
Fifteen ~ Four (Check against all of the above phenomenon): Yes conduction
Four. Following terminal ~ body of the video distributor vehicle side harness connector
Caution : Only abnormal route inspection in accordance with the phenomenon SKIA2710J
Fifteen ~ Body earth (to inspect against all of the above : No conduction
phenomenon)
Inspection results OK Or
OK » Three What
NG »Repair the video distributor - the front display unit between the harness
AV - 196
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. To connect the connector of the video distributor and the front display unit.
3. "Screen adjustment" of the check and adjustment mode To display the color bar at. " Confirmation - Adjustment mode "( AV-164 page ) See.
Four. Voltage waveform between the following terminals of the video distributor vehicle side harness connector
B
To inspect the.
C
Measuring terminal
Measurement condition Reference value
(+) (-)
D
To display a color bar on the
SKIA0165J
Measuring terminal
Measurement condition Reference value
(+) (-) F
SKIA0166J
Measuring terminal
SKIA2892J
Measurement condition Reference value
(+) (-)
JA
SKIA0167J
Inspection results OK Or
AV - 197
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
2. Of check and adjustment mode " Screen Adjustment " To check the color at. " Screen "( AV-164 page ) See.
NG » Two What
2. Harness inspection
2. Video distributor ( TH Type Sixteen Remove the connector of the pole) and the rear display unit.
3. Following terminal of the video distributor vehicle side harness connector ~ Riyadisu
To check the continuity between the following terminals of the play unit vehicle-side harness connector.
twenty five ~ twenty four (When the blue Cal) : Yes conduction
27 ~ twenty one (Check against all of the above phenomenon): Yes conduction
SKIA2715J
Four. Following terminal ~ body of the video distributor vehicle side harness connector
phenomenon)
Inspection results OK Or
OK » Three What
NG »Repair the video distributor - rear display unit between the harness
AV - 198
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. To connect the connector of the video distributor and rear display unit.
3. "Screen adjustment" of the check and adjustment mode To display the color bar at. " Confirmation - Adjustment mode "( AV-164 page ) See.
Four. Voltage waveform between the following terminals of the video distributor vehicle side harness connector
B
To inspect the.
C
Measuring terminal
Measurement condition Reference value
(+) (-)
D
To display a color bar on the
SKIA0165J
Measuring terminal
Measurement condition Reference value
(+) (-) F
SKIA0166J
Measuring terminal
SKIA2893J
Measurement condition Reference value
(+) (-)
JA
SKIA0167J
Inspection results OK Or
AV - 199
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. Harness inspection
2. Video distributor ( TH Type Twelve Pole) and NAVI control unit( TH Type Forty Remove the connector of the pole).
3. Video distributor vehicle side harness connector 59 Ban terminal ~ NAVI Comte
Roll unit vehicle-side harness connector Thirty To check the continuity between the turn terminal.
Four. Video distributor vehicle side harness connector 59 Ban terminal ~ Body Architect
SKIA2722J
Inspection results OK Or
OK » Two What
NG »Video distributor - NAVI To repair the control unit between the harness
1. Video distributor and NAVI To connect the connector of the control unit.
3. Of check and adjustment mode " Screen Adjustment " To display the color bar at. " Confirmation - Adjustment mode "( AV-164 page ) See.
Four. Video distributor vehicle side harness connector 59 Ban terminal ~ Body Architect
Measuring terminal
Measurement condition Reference value
(+) (-)
adjustment function
SKIA0164J
Inspection results OK Or
AV - 200
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. Harness inspection
2. Video distributor ( TH Type twenty four Remove the connector of the pole) and the front display unit.
3. Video distributor vehicle side harness connector Twenty Ban terminal ~ front di
B
Spray unit vehicle-side connector twenty four You check the continuity between the turn terminal.
Four. Video distributor vehicle side harness connector Twenty Ban terminal ~ Body Architect
SKIA2726J D
Inspection results OK Or
OK » Two What
NG »Repair the video distributor - the front display unit between the harness
1. To connect the connector of the video distributor and the front display unit.
Four. Video distributor vehicle side harness connector Twenty Ban terminal ~ Body Architect
G
Measuring terminal
Measurement condition Reference value
(+) (-)
H
To display a color bar
on the screen
Twenty body
Earth adjustment of the
SKIA2931J
SKIA0164J
I
Inspection results OK Or
AV
AV - 201
Car Wings corresponding twin monitor TV / Navigation system ( DVD method)
1. Harness inspection
2. Video distributor ( TH Type Sixteen Remove the connector of the pole) and the rear display unit.
3. 映像分配器車両側ハーネスコネクター 29 、 31 番端子~リヤディ
スプレイユニット車両側ハーネスコネクター 19 、 18 番端子間 の 導通を点検する。
29 ~ 19 :導通あり
31 ~ 18 :導通あり
4. 映像分配器車両側ハーネスコネクター 29 、 31 番端子~ボディ
アース間の導通を点検する。
31 ~ボディーアース :導通なし
点検結果は OK か
OK ≫2へ
NG ≫ 映像分配器~フロントディスプレイユニット間ハーネスを修理する
2. 垂直同期信号点検
1. 映像分配器及びリヤディスプレイユニットのコネクターを接続する。
2. キースイッチを ON にする。
の電圧波形を点検する。
測定端子
測定条件 基準値
(+) (-)
確認・調整機能の 画面調
29 31 整でカラー バーを表示す
る SKIA2932J
SKIA0161J
点検結果は OK か
OK ≫ リヤディスプレイユニットを交換する
NG ≫ 映像分配器を交換する
AV - 202
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
ビデオのみ映像が出ない JKS00C0T
1. ビデオデッキ点検 A
ビデオデッキを他の TV 等に接続したとき映像が出るか?
点検結果は OK か
OK ≫2へ B
NG ≫ ビデオデッキ不良
2. ハーネス点検
C
1. キースイッチを OFF にする。
2. TV チューナー( TK 型 6 極)及びビデオジャックのコネクターを外す。
3. TV チューナー車両側ハーネスコネクター 29 、 30 番端子~ビデ
オジャック車両側ハーネスコネクター 1 、 3 番端子間の導通を点 検する。 D
29 ~ 1 :導通あり
30 ~ 3 :導通あり
E
4. TV チューナー車両側ハーネスコネクター 29 、 30 番端子~ボディ
アース間の導通を点検する。
F
30 ~ボディーアース :導通なし
点検結果は OK か
OK ≫3へ
NG ≫ TV チューナー~ビデオジャック間ハーネスを修理する G
AV
AV - 203
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
3. ビデオ映像信号点検
1. TV チューナー及びビデオジャックのコネクターを接続する。
2. キースイッチを ON にする。
3. ビデオを再生し、 TV チューナー車両側ハーネスコネクター 29 、
30 番端子~ 26 番端子間の電圧波形を点検する。
測定端子
測定条件 基準値
(+) (-)
29
26 ビデオ再生時
30 SKIA2729J
SKIA0189J
点検結果は OK か
OK ≫ 現象に応じて下記を点検する。
NG ≫ ビデオジャックを交換する
TV 、ビデオ音声が全席スピーカーから出ない JKS00C0X
1. 現象確認 1
1. キースイッチを ACC にする。
2. 電子チューナーラジオを ON にし、ラジオ放送を受信する。
全席スピーカーから音声が出力されているか?
YES ≫ 2 へ
NO ≫ 電子チューナーラジオを交換する
2. 現象確認 2
1. 地図 DVD – ROM を取り出し、 DVD ビデオソフトを挿入する。
全席スピーカーから音声が出力されているか?
YES ≫ 3 へ
NO ≫5へ
AV - 204
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
3. ハーネス点検
A
1. キースイッチを OFF にする。
3. NAVI コントロールユニット車両側ハーネスコネクター 43 、 44 、
45 、 46 、 48 番端子~ TV チューナー車両側ハーネスコネクター
B
20 、 19 、 21 、 6 、 8 番端間の導通を点検する。
43 ~ 20 :導通あり
44 ~ 19 :導通あり
45 ~ 21 :導通あり C
46 ~ 6 :導通あり
48 ~ 8 :導通あり
SKIA2627J
4. NAVI コントロールユニット車両側ハーネスコネクター 43 、 44 、
D
45 、 46 、 48 番端子~ボディーアース間の導通を点検する。
43 ~ボディーアース :導通なし
44 ~ボディーアース :導通なし
45 ~ボディーアース :導通なし E
46 ~ボディーアース :導通なし
48 ~ボディーアース :導通なし
点検結果は OK か
F
OK ≫4へ
4. TV 音声信号点検 G
2. キースイッチを ON にする。
3. TV 放送を受信し、 TV チューナー車両側ハーネスコネクター 6 、
H
8 、 19 、 21 番端子~ 20 番端子間の電圧波形を点検する。
測定端子
測定条件 基準値
(+) (-)
I
6
19
20 TV 放送受信時
SKIA2936J
J
21
SKIA0177J
点検結果は OK か
OK ≫ NAVI コントロールユニットを交換する AV
NG ≫ TV チューナーを交換する
AV - 205
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
5. DIN ケーブル点検
NAVI コントロールユニット( DIN8P )~映像分配器間( DIN7P )及び映像分配器( DIN8P )~オーディオ( DIN8P ) 間の DIN ケーブに接続不良又は
ピン抜け等がないか点検する。
点検結果は OK か
OK ≫ NAVI コントロールユニットを交換する
NG ≫ DIN ケーブルを接続し直し、再度現象確認を行う
TV 、ビデオ音声がフロントスピーカーからのみ出ない JKS00C12
TV 、ビデオ音声がリヤスピーカーからのみ出ない JKS00C0Z
ビデオ音声のみ出ない JKS00C0U
1. ビデオデッキ点検
ビデオデッキを他の TV 等に接続したとき音声が出るか?
点検結果は OK か
OK ≫2へ
NG ≫ ビデオデッキ不良
2. ハーネス点検
1. キースイッチを OFF にする。
2. TV チューナー( TK 型 6 極)及びビデオジャックのコネクターを外す。
3. TV チューナー車両側ハーネスコネクター 25 、 27 、 28 、番端子~
ビデオジャック車両側コネクター 4 、 5 、 6 番端子間 の導通を点 検する。
25 ~ 4 :導通あり
27 ~ 5 :導通あり
28 ~ 6 :導通あり
4. TV チューナー車両側ハーネスコネクター 25 、 27 、 28 番端子~
ボディアース間の導通を点検する。 SKIA2732J
25 ~ボディーアース :導通なし
27 ~ボディーアース :導通なし
28 ~ボディーアース :導通なし
点検結果は OK か
OK ≫3へ
NG ≫ TV チューナー~ビデオジャック間ハーネスを修理する
AV - 206
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
3. ビデオ音声信号点検
A
1. TV チューナー及びビデオジャックのコネクターを接続する。
2. キースイッチを ON にする。
3. ビデオを再生し、 TV チューナー車両側ハーネスコネクター 25 、
27 番端子~ 28 番端子間の電圧波形を点検する。
B
測定端子
測定条件 基準値
(+) (-)
25
C
28 ビデオ再生時
27 SKIA2731J
D
SKIA0188J
点検結果は OK か
OK ≫ TV チューナーを交換する
E
NG ≫ ビデオジャックを交換する
1. 通信点検 F
1. キースイッチを ON にする。
故障診断画面は起動するか? G
YES ≫ NAVI コントロールユニットを交換する
フロント、リヤディスプレイ共自動減光しない JKS00CS4
H
1. 現象確認
1. キースイッチを ON にする。
I
2. ライトスイッチ( 1 段)を ON し、オートライトセンサーを手でふさいだ時と光を当てた時でコンビネーション
メーターの輝度が変化することを確認する。(自動減光機能)
コンビネーションメーターの輝度は変化したか?
YES ≫ 2 へ
J
NO ≫ オートライトシステムの点検を行う。 「 オートライト受光センサー系統点検」( LT-13 ページ ) を参照。
AV
AV - 207
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
2. 車両信号診断
• エンジンを始動させる。
<ライト信号> ライトスイッ
チ1段 : ON
点検結果は OK か?
OK ≫ NAVI コントロールユニットを交換する
NG ≫3へ
3. ハーネス点検
1. キースイッチを OFF にする。
8 ~ 14 :導通あり
8 ~ボディーアース :導通なし
SKIA3013J
点検結果は OK か
OK ≫4へ
4. 自動減光信号点検
1. NAVI コントロールユニット及び BCM のコネクターを接続する。
2. キースイッチを ON にする。
測定端子
測定条件 電圧( V )
(+) (-)
ボディー
8
アース ライト SW ON (一段)で オートラ
イト受光センサー に光を当てないと 約 12 SKIA2602J
点検結果は OK か?
OK ≫ NAVI コントロールユニットを交換する
NG ≫ BCM を交換する
AV - 208
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
フロントディスプレイのみ自動減光しない JKS00CST
リヤディスプレイのみ自動減光しない JKS00CSU
1. リモコン受光部の確認
後席ナビリモコンの受光部は以下の 2 箇所である。
C
受光部 操作スイッチ
オーバーヘッドコンソール内 (ディス :開 / 閉スイッチ
プレイ部)
リヤディスプレイ右部 :上記以外のすべてのスイッチ
D
≫ 確認後、 2 へ
2. リモコン本体及び受光部の確認及び点検 E
下記の項目について確認、点検を行う。
• リモコンを受光部に向けて操作しているか
• リモコン受光部にシールや汚れ等、信号の妨げになるものが付着していないか F
• リモコン電池の寿命ではないか
点検結果は OK か?
OK ≫3へ
NG ≫ • リモコンを受光部に向けて操作する G
• 信号の妨げになっているシール及び汚れを取り除く
• 電池が寿命の場合は交換する
AV
AV - 209
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
3. 通信信号ハーネス点検
1. キースイッチを OFF にする。
2. 映像分配器( TH 型 16 極)及びリヤディスプレイユニットのコネクターを外す。
3. 映像分配器車両側ハーネスコネクター 38 、 39 、 40 番端子~リヤ
ディスプレイユニット車両側ハーネスコネクター 8 、 9 、 10 番端 子の導通を点検す
る。
38 ~ 8 :導通あり
39 ~ 9 :導通あり
40 ~ 10 :導通あり
38 ~ボディーアース :導通なし
39 ~ボディーアース :導通なし
40 ~ボディーアース :導通なし
点検結果は OK か?
OK ≫4へ
NG ≫ 映像分配器~リヤディスプレイユニット間ハーネスを修理する
4. 通信信号点検
1. 映像分配器及びリヤディスプレイユニットのコネクターを接続する。
2. キースイッチを ON し、映像分配器車両側ハーネスコネクターの
39 、 40 番端子~ 38 番端子間の電圧波形を点検する。
測定端子
測定条件 基準値
(+) (-)
39
SKIA2664J
ナビ画面にし、 後席ナ
ビリモコ ンでナビ操作 SKIA0220J
38
を する
40
SKIA0219J
点検結果は OK か?
OK ≫ リヤディスプレイユニットを交換する
NG ≫ • 電圧値が一定(約 5V 付近)で電圧波形が現れない場合はリヤディスプレイユニットを交換する
• 電圧値が一定(約 0V 付近)で電圧波形が現れない場合は映像分配器を交換する
AV - 210
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
後席ナビリモコンによるナビ操作がすべて効かない JKS00CSS
1. 後席マルチリモコン作動点検点検 A
1. キースイッチを ON にする。
2. 後席マルチリモコンを操作し、各システムが正常に作動することを確認する。
点検結果は OK か? B
OK ≫ 後席ナビリモコンを交換する
後席ナビリモコンで後席独立スイッチを押しても独立して音が聞こえない JKS00C0V C
1. 後席音声点検
1. キースイッチを ACC にする。
D
2. 電子チューナーラジオを ON し、リヤスピーカーから音が出力されていることを確認する。
点検結果は OK か
OK ≫3へ
NG ≫2へ E
2. DIN ケーブル点検
NAVI コントロールユニット( DIN8P )~映像分配器間( DIN7P )及び映像分配器( DIN8P )~オーディオ( DIN8P ) 間の DIN ケーブに接続不良又は
F
ピン抜け等がないか点検する。
点検結果は OK か
3. リモコン作動点検
H
1. キースイッチを ON にする。
YES ≫ 映像分配器を交換する
I
NO ≫ 「 リヤディスプレイ開 / 閉操作以外のリモコン操作が効かない」( AV-209 ページ ) を実施する
1. 後席マルチリモコン作動点検点検 J
1. キースイッチを ON にする。
2. 後席マルチリモコンを操作し、各システムが正常に作動することを確認する。
点検結果は OK か? AV
OK ≫3へ
NG ≫2へ
AV - 211
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
2. BCM 自己診断(通信診断)点検
BCM 自己診断(通信診断)を行う。「 BCS ボディーコントロールシステム」の 「 通信診断 」 (BCS-34 ページ ) を参照。
故障コード 52 が表示されたか?
NO ≫ 後席ナビリモコンを交換する
3. リモコン本体及び受光部の確認及び点検
下記の項目について確認、点検を行う。
• リモコンを受光部(オーバーヘッドコンソール内)に向けて操作しているか
• リモコン受光部にシールや汚れ等、信号の妨げになるものが付着していないか
• リモコン電池の寿命ではないか
点検結果は OK か?
YES ≫ 4 へ
NO ≫ • リモコンを受光部に向けて操作する
• 信号の妨げになっているシール及び汚れを取り除く
• 電池が寿命の場合は交換する
4. ハーネス点検
1. キースイッチを OFF にする。
2. 映像分配器( TH 型 8 極)及びルーフコントロールユニットのコネクターを外す。
3. 映像分配器車両側ハーネスコネクター 46 番端子~ルーフコント
46 ~ 9 :導通あり
4. 映像分配器車両側ハーネスコネクター 46 番端子~ボディーアー
ス間の導通を点検する。
46 ~ボディーアース :導通なし
SKIA2734J
点検結果は OK か
OK ≫5へ
NG ≫ 映像分配器~ルーフコントロールユニット間ハーネスを修理する
AV - 212
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
5. 後席ナビリモコン(開 / 閉)信号点検
A
1. 映像分配器及びルーフコントロールユニットのコネクターを接続する。
2. キースイッチを ON にする。
3. 後席ナビリモコンの開 / 閉スイッチを押して、映像分配器車両側
ハーネスコネクター 46 ~ボディーアース間の電圧を点検する。
B
測定条件 電圧( V )
(+) (-)
– 約5
46 ボディー
C
アース 後席ナビリモコン の開 / 閉 約 3.5 以下 (開 / 閉 SW を押
SW を押す した瞬間)
点検結果は OK か
SKIA2735J
後席ナビリモコンで角度スイッチを操作してもリヤディスプレイの角度が変わらな い
JKS00C1A
E
1. リモコン本体及び受光部の確認及び点検
下記の項目について確認、点検を行う。
• リモコンを受光部(リヤディスプレイ右部)に向けて操作しているか F
• リモコン受光部にシールや汚れ等、信号の妨げになるものが付着していないか
• リモコン電池の寿命ではないか
点検結果は OK か?
G
YES ≫ リヤディスプレイユニットを交換する
NO ≫ • リモコンを受光部に向けて操作する
• 信号の妨げになっているシール及び汚れを取り除く
• 電池が寿命の場合は交換する
H
音声によるナビ操作ができない JKS00C1B
1. 自己診断
1. キースイッチを ON にする。
J
2. 自己診断モードを行う。 「 自己診断モード」( AV-155 ページ ) を参照。
YES ≫ 2 へ
AV - 213
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
2. BCM 自己診断(スイッチモニタ)点検
BCM 自己診断(スイッチモニタ)を行う。「 BCS ボディーコントロールシステム」の 「スイッチモニタ」( BCS-39
ページ ) を参照。
ステアリングホイールスイッチは正常に作動するか?
NO ≫3へ
3. ハーネス点検
1. キースイッチを OFF にする。
2. スパイラルケーブル~ステアリングホイールスイッチ間のハーネスに断線がないか目視点検する。
点検結果は OK か?
OK ≫ ステアリングホイールスイッチを交換する
NG ≫ スパイラルケーブル~ステアリングホイールスイッチ間ハーネスを修理する
ガイド音声が出ない JKS00C1D
1. 車両信号点検
1. エンジンを始動する。
し、その時の車両信号を確認する。
<車速信号> 走行
時 : ON
停止時 : OFF
<リバース信号>
パーキングブレーキを踏む : ON
パーキングブレーキを踏まない : OFF
点検結果は OK か
OK ≫ NAVI コントロールユニットを交換する
燃費情報が出ない(走行しても平均燃費及び航続可能距離の表示が ″ ** ″ になる)
JKS00C1H
ドライブ情報が正確でない、メンテナンス情報が正確でない JKS00C1I
警告画面が出ない(充電警告表示を除く) JKS00C1J
AV - 214
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
システムが起動しない JKS00C1K
1. 電源系統点検 A
点検結果は OK か? B
OK ≫ NAVI コントロールユニットを交換する
NG ≫ 電源系不良
2. 自己診断点検 C
1. キースイッチを ON にする。
点検結果は OK か? D
OK ≫ NAVI コントロールユニットを交換する
前の状態が記憶されない JKS00C1L
1. バッテリー電源点検
F
NAVI コントロールユニットのバッテリー電源を点検する。 「 NAVI コントロールユニットの電源及びアース回路点検 」
(AV-167 ページ ) を参照。
点検結果は OK か?
OK ≫ NAVI コントロールユニットを交換する
G
NG ≫ NAVI コントロールユニットのバッテリー電源系統ハーネスを修理する
現在位置マークがずれる JKS00C1M
I
現在位置マークの方位が狂う JKS00C1O
1. 環境確認
GPS アンテナ付近に電波を遮る金属製の物や電波を発生する携帯電話などが置かれているか。又、ビルなどで遮ら れているか。
AV
確認結果は OK か?
OK ≫ • 故障ではない。
L
NG ≫2へ
AV - 215
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
2. 自己診断
1. キースイッチを ON にする。
走行テスト JKS00CS6
異常ではない現象例 JKS00C1R
プログラムローディング JKS00C1S
取り外し
ページ ) を参照。
ページ ) を参照。
ントロールユニットを取り外す。
PKIA1286J
4. 取付スクリュー( 4 本)を外し、ブラケットを取り外す。
PKIA1287J
取り付け
取り付けは取り外しの逆の手順で行う。
AV - 216
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
取り外し A
ンテナを取り外す。 B
PKIA1288J
D
取り付け
取り付けは取り外しの逆の手順で行う。
取り外し
取り外す。 F
外す。
PKIA1289J
取り付け H
取り付けは取り外しの逆の手順で行う。
取り外し I
2. 取付ボルト( 4 本)及びハーネスコネクターを外し、フロントディ
J
スプレイユニット ASSY を取り外す。
AV
PKIA1290J
AV - 217
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
取り付け
取り付けは取り外しの逆の手順で行う。
PKIA1291J
7. メーターブラケット 8. 電源ボックス
1. 取付スクリュー( 2 本)を外し、イルミネーションコントロールス
2. 取付スクリュー( 7 本)を外し、メーターブラケットカバーを取り
外す。
B を取り外す。
SKIA2488J
4. フロントディスプレイユニット裏面のフレキシブルプリントサー
キット固定クリップ及びコネクターのロックを外す。
5. コネクターからフレキシブルプリントサーキットを引き抜く。
PKIA1292J
AV - 218
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
6. 取付スクリュー( 4 本)を外し、電源ボックスを取り外す。
PKIA1293J
C
7. ナビフィニッシャー取付スクリュー( 4 本)を外し、ナビフィニッ
シャー A を取り外す。
8. フロントディスプレイユニット取付スクリュー( 4 本)を外し、フ
ロントディスプレイユニットを取り外す。 D
9. チューナーブラケット取付スクリュー( 4 本)を外し、チューナー
ブラケットを取り外す。
E
PKIA1294J
取り外し F
1. テープを巻いたマイナスドライバー等を差し込んで、リヤディスプ
レイフィニッシャーを取り外す。
2. 左スタッドボルト部のハーネスクリップ( 2 個)を外す。
G
3. ヘッドライニングを外す。(サンルーフ無車)
ヘッドライニングフロントサンルーフ開口部リヤ側のデュアル ロックファスナー
( 4 箇所)を外す。(サンルーフ付車)
H
PKIA1295J
ユニットを取り外す。 I
注意 : リヤディスプレイユニットは、ヘッドライニングを浮かせて一
旦車両前方にずらし、後側を車両下方に下げて後方から取り出 すこと。
PKIA1296J
AV
取り付け
取り付けは下記に注意し取り外しの逆の手順で行う。
注意 : 取り付ける際は、先にクリップでリヤディスプレイユニットを固定してから行う。
AV - 219
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
TV チューナー取り外し、取り付け JKS00CRX
取り外し
1. リヤサイドフィニッシャーセンター右、及びリヤサイドフィニッ
シャーロア右を取り外す。「 EI 外装・内装」の 「リヤサイドフィ ニッシャーセンタ
ー 」 (EI-31 ページ ) 、 「 リヤサイドフィニッシャー ロア」( EI-30 ページ ) を参照。
PKIA1299J
取り付け
取り付けは取り外しの逆の手順で行う。
映像分配器(後席音声独立機能付き)の取り外し、取り付け JKS00BEX
取り外し
2. 取付ボルト( 4 本)及びコネクターを外し、映像分配器を取り外す。
PKIA1297J
3. 取付スクリュー( 4 本)を外し、ブラケットを取り外す。
PKIA1298J
取り付け
取り付けは取り外しの逆の手順で行う。
AV - 220
カーウイングス対応ツインモニター TV/ ナビゲーションシステム( DVD 方式)
ビデオジャックの取り外し、取り付け JKS00BEZ
取り外し A
2. サードシートレールフィニッシャー右を取り外す。「 EI 外装・内装」
B
の 「取り外し、取り付け」( EI-28 ページ ) を参照。
3. ビデオジャックキャップを取り外す。
4. サードシートレールフィニッシャー右裏面の取付スクリュー( 3 本)
C
を外し、ビデオジャックを取り外す。
PKIA1300J
取り付け
取り付けは取り外しの逆の手順で行う。
AV
AV - 221
カーウイングス&ハンドフリー電話
カーウイングス&ハンドフリー電話 PFP:25915
システム概要 JKS00C2U
• サービス加入手続きをせずに携帯電話を接続してもハンドフリー電話での通話は可能である。
• 情報センターから受信した情報やメールなどは、自動的に内容を音声で読み上げるシステムを採用した。
SKIA2796J
AV - 222
カーウイングス&ハンドフリー電話
構成部品取付位置 JKS00C2X
SKIA2797J F
システム図 JKS00C2Y
AV
SKIA2803J
AV - 223
カーウイングス&ハンドフリー電話
回路図 JKS00C2Z
TKWA0695J
AV - 224
カーウイングス&ハンドフリー電話
入出力信号基準値測定に関する注意 JKS00CNF
端子 番
測定条件 B
号 信号の 入
信号名称 基準値
出力 キー
+– 操作又は状態
SW
5 IGN 電源 入力 ON – 電源電圧
C
7 ボ ACC 電源 入力 ACC – 電源電圧
デ
9 アース – ON – 約0
ィ
10 | BAT 電源 入力 OFF – 電源電圧
ア
11 アース – ON – 約0
| D
12 ス BAT 電源 入力 OFF – 電源電圧
13 シールド(通信) – ON – 約0
14 通信信号(-) 入出力 ON
SKIA2553J
F
13 車両情報 SW を押す
16 通信信号(+) 入出力 ON
G
SKIA2553J
37 電話音声信号(-) 出力 ON ハンドフリー通話状態
ボ
ELL0234D
I
デ
ィ
約 0.6V 以下
38 | 電話音声 ON 信号 出力 ON 通話時
ア
非通話時 約 5 以上
|
ス J
40 電話音声信号(+) 出力 ON ハンドフリー通話状態
AV
ELL0234D
AV - 225
カーウイングス&ハンドフリー電話
端子 番
測定条件
号 信号の 入
信号名称 基準値
出力 キー
+– 操作又は状態
SW
47 49 マイク信号 入力 ON マイクに向かって声を発声す
る
SKIA2557J
50 マイク電源 出力 ON – 約 5V
54 59 下りシリアル信号 入力 ON –
ELL0238D
ボ
デ
ィ
55 | シールド(送信・受信) – ON – 約 0V
ア
|
ス
ELL0240D
57 TCH クロック信号 ( CF ) 入力 ON
ボ
デ
ELL0239D
ィ
情報センター呼出し時
|
ア
|
ス
58 TCH フレーム信号( CB ) 入力 ON
ELL0237D
59 シリアル信号アース – ON – 約 0V
AV - 226
カーウイングス&ハンドフリー電話
端子 番
測定条件
号 信号の 入
信号名称 基準値
出力 A
キー
+– 操作又は状態
SW
ユニット電源制御信号 ( CE ) 約 0V
62 ボ 出力 ON 情報センター接続時
デ ハンドフリー通話時 約 5V
63 ィ
携帯電話制御信号 1 B
| 出力 ON ハンドフリー通話時 約 0V
64 ア
携帯電話制御信号 2
| 約 0V
66 ス ユニット有無信号( CD ) 出力 ON 携帯電話接続時
OFF 携帯電話接続時 約 4V (注意)
C
67 受信信号( BB ) 入力 ON ハンドフリー通話で相手の音
声を受信する
D
ELL0236D
55
E
ハンドフリー通話でマイクに 向かって
68 送信信号( BA ) 出力 ON 声を発声する(声の 大きさにより出力
が異なる)
ELL0235D
F
注意 : 電話機により電圧値は異なる
映像分配器入出力信号基準値 JKS00CWX
G
測定 端
測定条件
子 信号の 入
信号名称 基準値
出力 キー
+- 操作又は状態
SW
1 通信信号(+) 入出力 ON -
I
SKIA0175J
2 通信信号(-) 入出力 ON - J
SKIA0176J
ボ
デ
AV
ィ
3 | シールド(通信) – ON – 約 0V
ア
|
ス L
AV - 227
カーウイングス&ハンドフリー電話
測定 端
測定条件
子 信号の 入
信号名称 基準値
出力 キー
+- 操作又は状態
SW
4 通信信号(+) 入出力 ON -
SKIA0175J
5 通信信号(-) 入出力 ON -
SKIA0176J
ボ
デ
ィ
6 | シールド(通信) – ON – 約 0V
ア
|
ス
41 アース - ON - 約 0V
TV チューナー入出力信号基準値 JKS00CWY
測定 端
測定条件
子 信号の 入
信号名称 基準値
出力 キー
+- 操作又は状態
SW
1 通信信号(-) 入出力 ON
ボ
デ
ィ
集中 SW ( NAVI SW )のい ずれかを SKIA2553J
|
押す
ア
|
ス
2 通信信号(+) 入出力 ON
SKIA2553J
AV - 228
カーウイングス&ハンドフリー電話
測定 端
測定条件
子 信号の 入
信号名称 基準値
出力 A
キー
+- 操作又は状態
SW
SKIA2553J
E
23 ボ アース – ON – 約 0V
デ
ィ
|
24 ア
アース – ON – 約 0V
| F
ス
G
測定 端
測定条件
子 信号の 入
信号名称 基準値
出力 キー
+- 操作又は状態
SW
19 通信信号(-) 入出力 ON
40
押す
J
38 通信信号(+) 入出力 ON
SKIA2553J
AV
ボ
デ
ィ
40 | シールド(通信) – ON – 約 0V
ア
| L
ス
AV - 229
カーウイングス&ハンドフリー電話
測定 端
測定条件
子 信号の 入
信号名称 基準値
出力 キー
+- 操作又は状態
SW
49 – B/CAN – L – – – –
TEL ON
(押した状態):約 0V
ボイスコマンド ON
ステアリングホイール (押した状態):約 1.7V VOL (
50 入力 ON TEL 、ボイスコマンド、
SW 信号 B VOL ( DOWN )を押す
DOWN ) ON
(押した状態):約 3.3V
上記 SW OFF :約 5V
62
MODE ON
(押した状態):約 0V
CH ( UP ) ON
ステアリングホイール (押した状態):約 1.7V VOL (
61 入力 ON MODE 、 CH ( UP )、 VOL
SW 信号 A ( UP )を押す
UP ) ON
(押した状態):約 3.3V
上記 SW OFF :約 5V
ボ
デ
ィ
ステアリングホイール
62 | – ON – 約 0V
SW 信号アース
ア
|
ス
63 – B/CAN-H – – – –
故障診断の進め方 JKS00CNE
1. 故障現象又はお客さまの要求を確認する。
5. 各現象から故障診断を行い、原因を特定する。
6. 故障診断で不良と判定した構成部品を交換する前に、再度コネクターの接続確認を行う。
7. 不具合の原因を修理又は交換する。
8. 不具合のシステムが正常に作動するか?正常の場合は 9 へ。異常の場合は 5 へ。
9. 終了。
AV - 230
カーウイングス&ハンドフリー電話
故障診断機能 JKS00C4R
概要 A
• 故障診断機能は自動的に診断が行われる自己診断モードと、手動で操作する確認・調整モードがある。
• 自己診断モードは、本システムを構成する各ユニット間の接続確認と個々のユニット診断を一括実施し、結果を液 晶ディスプレイに表示する。
• 確認・調整モードは、人間の操作と判断を必要とする(システム側での自動判定ができない)故障診断、設定値の 確認・変更及びナビ関係のエラ B
ー履歴を表示する。
操作要領
1. エンジンを始動する。
C
• ”戻る”スイッチを押すとシステム初期画面となる。
E
SKIA2567J
3. ”故障診断”画面が表示される。
SKIA2568J
H
診断項目
モード 診断内容
確認 · 調整モード JKS00C4V
J
操作要領
SKIA2568J
AV - 231
カーウイングス&ハンドフリー電話
通信モデム設定
調整・確認内容
ハンドフリー音量調整 ハンドフリー通話時の受話音量の調整(大・基準・小)を行う。
通信モデム ID 確認 通信モデムのシリアル番号を確認する。
ハンドフリー電話のメモリー(リダイヤル、発信・着信履歴、短縮ダイヤル登 録番号など)を消去す
メモリー消去
る。
情報センター電話番号登録 各情報センターの電話番号を表示し、電話番号登録ができる。
• マイクに向かって話した声をフロントスピーカー(左側)から出力できる。
マイクスピーカー確認 • 決定 SW を押すと、フロントスピーカー(左側)から MUTE 音を出力する。 また、そのとき電子チ
ューナーラジオに ″ MUTE ″ の文字が表示される。
1. ヒューズ点検
NAVI コントロールユニットの下記ヒューズに溶断がないか点検する。
10 、 12 BAT 電源 # 38
7 ACC 電源 # 17
5 IGN 電源 # 11
点検結果は OK か?
OK ≫2へ
NG ≫ ヒューズが溶断していた場合は、溶断の原因を修復してから新しいヒューズに交換する
2. 電源回路点検
NAVI コントロールユニット( TH 型 12 極)のコネクターを外し、下 記表の車両側ハーネ
スコネクターの端子番号を(+)、ボディーアー スを(-)として測定する。
5 IGN 電源 ON 電源電圧
SKIA2593J
点検結果は OK か?
OK ≫3へ
NG ≫ NAVI コントロールユニット電源回路ハーネスを修理する 項目
AV - 232
カーウイングス&ハンドフリー電話
3. アース回路点検
A
NAVI コントロールユニットの下記車両側ハーネスコネクター~ボ ディーアース間の導
通を点検する。
端子番号 信号名称 キー SW 導通
9 、 11 アース OFF あり B
点検結果は OK か?
OK ≫ 正常
NG ≫ NAVI コントロールユニットアース回路ハーネスを修
C
SKIA2594J
理する
現象別故障診断 JKS00C59
概要 D
• カーウイングス( Auto DJ 、コンパスリンクライト)サービスを利用するには、各サービスごとに契約が必要となる。 また、各センターとの通信や
通話を行うと、携帯電話の通話料金がかかる。
• NAVI コントロールユニットを交換する場合はカーウイングス情報センターへの再登録が必要になる。
相手の音声が聞こえない JKS00C5B
F
1. 携帯電話の点検
お客様以外の対応機種の携帯電話に交換して現象を確認する。
G
同様な現象が再現されたか?
YES ≫ 2 へ
NO ≫ 携帯電話不良
2. マイクスピーカー点検 H
1. キースイッチを ON にする。
- 決定スイッチを押す。 I
YES ≫ 3 へ
AV
AV - 233
カーウイングス&ハンドフリー電話
3. ハーネス点検
1. キースイッチを OFF にする。
3. NAVI コントロールユニット車両側ハーネスコネクター 55 、 67 番
端子~ TEL ハーネス車両側接続コネクターの 19 、 16 番端子間の 導通を点検する。
55 ~ 19 :導通あり
67 ~ 16 :導通あり
4. NAVI コントロールユニット車両側ハーネスコネクター 55 、 67 番
端子~ボディーアース間の導通を点検する。
55 ~ボディーアース :導通なし
SKIA3023J
67 ~ボディーアース :導通なし
点検結果は OK か
OK ≫4へ
4. 受信音声信号点検
1. 携帯電話を接続する。
2. キースイッチを ON にし、ハンドフリー通話状態にする。
測定端子
測定条件 基準値
(+) (-)
ハンドフリー 通話
で相手の 音声を受 SKIA2815J
67 55
信す る
ELL0236D
点検結果は OK か
OK ≫5へ
NG ≫ TEL ハーネスを交換する
AV - 234
カーウイングス&ハンドフリー電話
5. ハーネス点検
A
1. キースイッチを OFF にする。
3. NAVI コントロールユニット車両側ハーネスコネクター 37 、 38 、
40 番端子~電子チューナーラジオ車両側ハーネスコネクター
B
29 、 20 、 30 番端子間の導通を点検する。
37 ~ 29 :導通あり
38 ~ 20 :導通あり
40 ~ 30 :導通あり C
4. NAVI コントロールユニット車両側ハーネスコネクター 37 、 38 、
40 番端子~ボディーアース間の導通を点検する。 SKIA2812J
37 ~ボディーアース :導通なし D
38 ~ボディーアース :導通なし
40 ~ボディーアース :導通なし
点検結果は OK か
E
OK ≫6へ
NG ≫ NAVI コントロールユニット~電子チューナーラジオ間ハーネスを修理する
6. 電話音声信号点検 F
1. NAVI コントロールユニット及び電子チューナーラジオのコネクターを接続する。
2. キースイッチを ON にする。
3. NAVI コントロールユニット車両側ハーネスコネクター 37 、 40 番
G
端子~ボディーアース間の電圧波形を点検する。
測定端子
測定条件 基準値
(+) (-)
37 H
ボディー ハンドフリー 通話
40 アース 状態
I
ELL0234D
測定端子
測定条件 基準値
(+) (-)
AV
通話時 約 0.6V 以下 SKIA2904J
38 ボディー
アース 非通話時 約 5V 以上
点検結果は OK か
L
OK ≫ 電子チューナーラジオを交換する
NG ≫ NAVI コントロールユニットを交換する
AV - 235
カーウイングス&ハンドフリー電話
相手に音声が伝わらない JKS00C5D
1. 携帯電話の点検
お客様以外の対応機種の携帯電話に交換して現象を確認する。
同様な現象が再現されたか?
YES ≫ 2 へ
NO ≫ 携帯電話不良
2. マイクスピーカー点検
1. キースイッチを ON にする。
- マイク(オーバーヘッドコンソール内)に向かって声を出す。
フロントスピーカー(左側)から音声が出力されているか?
YES ≫ 5 へ
NO ≫3へ
3. マイクハーネスの点検
1. キースイッチを OFF にする。
3. NAVI コントロールユニット車両側ハーネスコネクター 47 、 49 、
50 番端子~マイク車両側ハーネスコネクター 1 、 2 、 3 番端子間 の導通を点検する。
47 ~ 1 :導通あり
49 ~ 2 :導通あり
50 ~ 3 :導通あり
4. NAVI コントロールユニット車両側ハーネスコネクター 47 、 49 、
50 番端子~ボディーアース間の導通を点検する。 SKIA2641J
47 ~ボディーアース :導通なし
49 ~ボディーアース :導通なし
50 ~ボディーアース :導通なし
点検結果は OK か
OK ≫4へ
NG ≫ NAVI コントロールユニット~マイク間ハーネスを修理する
AV - 236
カーウイングス&ハンドフリー電話
4. マイク信号点検
A
1. NAVI コントロールユニット及びマイクのコネクターを接続する。
2. キースイッチを ON にする。
測定条件 基準値
(+) (-)
50 49 – 約 5V
C
D
測定端子
測定条件 基準値
(+) (-)
E
マイクに向 かって
47 49 声を発 声する
SKIA2905J
F
SKIA2557J
点検結果は OK か
NO ≫ マイクを交換する
G
5. ハーネス点検
1. キースイッチを OFF にする。
H
2. NAVI コントロールユニット( TH 型 24 極)及び TEL ハーネスのコネクターを外す。
3. NAVI コントロールユニット車両側ハーネスコネクター 55 、 68 番
端子~ TEL ハーネス車両側接続コネクターの 19 、 9 番端子間の 導通を点検する。
I
55 ~ 19 :導通あり
68 ~ 9 :導通あり
4. NAVI コントロールユニット車両側ハーネスコネクター 55 、 67 番
端子~ボディーアース間の導通を点検する。 J
68 ~ボディーアース :導通なし
点検結果は OK か AV
OK ≫6へ
AV - 237
カーウイングス&ハンドフリー電話
6. 送信音声信号点検
1. キースイッチを OFF にし、携帯電話を接続する。
2. キースイッチを ON にする。
3. ハンドフリー通話状態でマイクに向かって声を発声し、 NAVI コ
測定端子
測定条件 基準値
(+) (-)
ハンドフリー通話 でマイ
クに向かっ て声を発声する
SKIA2820J
68 55 (声の大きさによっ て出
力が異なる)
ELL0235D
点検結果は OK か
OK ≫ NAVI コントロールユニットを交換する
NG ≫ TEL ハーネスを交換する
1. 現象確認
1. キースイッチを ON にする。
点検結果は OK か?
YES ≫ ステアリングホイールスイッチを交換する。
NO ≫2へ
2. ハーネス点検(スパイラルケーブル~ステアリングホイールスイッチ)
1. キースイッチを OFF にする。
2. ステアリングホイールを取り外す。
3. スパイラルケーブル~ステアリングホイールスイッチ間ハーネスに断線がないか目視点検する。
点検結果は OK か?
OK ≫3へ
NG ≫ スパイラルケーブル~ステアリングホイールスイッチ間ハーネスを修理する
AV - 238
カーウイングス&ハンドフリー電話
3. ハーネス点検(スパイラルケーブル~ BCM )
A
1. BCM のコネクターを外す。
B
50 ~ 32 :導通あり
61 ~ 24 :導通あり
62 ~ 31 :導通あり
C
3. BCM 車両側コネクター 50 、 61 、 62 番端子~ボディーアース間
の導通を点検する。 SKIA2533J
50 ~ボディーアース :導通なし
61 ~ボディーアース :導通なし
D
62 ~ボディーアース :導通なし
点検結果は OK か?
OK ≫4へ
E
NG ≫ BCM ~スパイラルケーブル間ハーネスを修理する
4. 故障診断画面の起動点検
故障診断画面を起動する。 「 故障診断機能」( AV-59 ページ ) を参照。 F
故障診断画面は起動したか?
発信 / 着信ができない JKS00C5E
H
1. 携帯電話の点検
お客様以外の対応機種の携帯電話に交換して現象を確認する。
I
同様な現象が再現されたか?
YES ≫ 2 へ
NO ≫ 携帯電話不良
AV
AV - 239
カーウイングス&ハンドフリー電話
2. ハーネス点検
1. キースイッチを OFF にする。
3. NAVI コントロールユニット車両側ハーネスコネクター 54 、 56 、
59 、 63 、 64 番端子~ TEL ハーネス車両側接続コネクターの 17 、
7 、 6 、 15 、 14 番端子間の導通を点検する。
54 ~ 17 :導通あり
56 ~ 7 :導通あり
59 ~ 6 :導通あり
63 ~ 15 :導通あり
64 ~ 14 :導通あり
SKIA3045J
4. NAVI コントロールユニット車両側ハーネスコネクター 54 、 56 、
59 、 63 、 64 番端子~ボディーアース間の導通を点検する。
54 ~ボディーアース :導通なし
56 ~ボディーアース :導通なし
59 ~ボディーアース :導通なし
63 ~ボディーアース :導通なし
64 ~ボディーアース :導通なし
点検結果は OK か
OK ≫3へ
3. 下りシリアル信号点検
1. キースイッチを OFF にし、携帯電話を接続する。
2. キースイッチを ON にする。
測定端子
測定条件 基準値
(+) (-)
54 59 –
SKIA2831J
ELL0238D
点検結果は OK か
OK ≫4へ
NG ≫ TEL ハーネスを交換する
AV - 240
カーウイングス&ハンドフリー電話
4. 上りシリアル信号点検
A
1. TEL スイッチを押してメモリー呼び出し操作を行う。
測定端子 B
測定条件 基準値
(+) (-)
ELL0240D
点検結果は OK か
OK ≫5へ
NG ≫ NAVI コントロールユニットを交換する
E
5. 携帯電話制御信号点検
1. TEL スイッチを押し、ハンドフリー通話状態にする。
2. NAVI コントロールユニット車両側ハーネスコネクター 63 、 64 番 F
端子~ボディーアース間の電圧を点検する。
測定端子
測定条件 基準値
(+) (-)
G
63 、 ボディー
約 0V
64 アース ハンドフリー通話時
点検結果は OK か
NG ≫ NAVI コントロールユニットを交換する
情報センターとの通信ができない JKS00C3B
I
1. 携帯電話の点検
お客様以外の対応機種の携帯電話に交換して現象を確認する。
同様な現象が再現されたか?
J
YES ≫ 2 へ
NO ≫ 携帯電話不良
AV
AV - 241
カーウイングス&ハンドフリー電話
2. ハーネス点検
1. キースイッチを OFF にする。
3. NAVI コントロールユニット車両側ハーネスコネクター 57 、 58 、
62 、 66 番端子~ TEL ハーネス車両側接続コネクターの 18 、 8 、
13 、 5 番端子間の導通を点検する。
57 ~ 18 :導通あり
58 ~ 8 :導通あり
62 ~ 13 :導通あり
66 ~ 5 :導通あり
62 、 66 番端子~ボディーアース間の導通を点検する。
57 ~ボディーアース :導通なし
58 ~ボディーアース :導通なし
62 ~ボディーアース :導通なし
66 ~ボディーアース :導通なし
点検結果は OK か
OK ≫3へ
AV - 242
カーウイングス&ハンドフリー電話
2. TEL ハーネスに携帯電話を接続する。
3. キースイッチを ON にする。
4. TEL スイッチを押し、情報センターへ発信する。
B
5. NAVI コントロールユニット車両側ハーネスコネクター 57 、 58 番
端子~ボディーアース間の電圧波形を点検する。
測定条件 基準値 C
(+) (-)
57 D
SKIA2842J
アース し時
E
58
F
ELL0237D
点検結果は OK か
OK ≫4へ
G
NG ≫ TEL ハーネスを交換する
4. ユニット有無信号点検
H
1. 情報センターとの接続を切断する。
測定端子 キー
測定条件 基準値
(+) (-) SW 状態
ON 携帯電話接続時 約 0V
66 ボディー
アース OFF 携帯電話接続時 約 4V (注意) J
SKIA2843J
注意 : 電話機により電圧値は異なる。
点検結果は OK か
OK ≫5へ
AV
NG ≫ NAVI コントロールユニットを交換する 測定端子
AV - 243
カーウイングス&ハンドフリー電話
5. ユニット電源制御信号点検
1. キースイッチを ON にする。
2. TEL スイッチを押し、情報センターに接続する。
測定条件 基準値
(+) (-)
62 ボディー 約 0V
アース 情報センター接続時
4. 情報センターとの接続を切断する。
測定端子
測定条件 基準値
(+) (-)
62 ボディー 約 5V
アース ハンドフリー通話時
点検結果は OK か
OK ≫ TEL ハーネスを交換する
NG ≫ NAVI コントロールユニットを交換する
音声案内及び音声読み上げ音が出ない JKS00C5C
1. 現象確認
1. キースイッチを ACC にする。
2. 電子チューナーラジオを ON にし、フロントスピーカー(右側)から音が出力されることを確認する。
点検結果は OK か?
OK ≫2へ
2. 音声ガイド確認
1. キースイッチを ON にする。
3. 音声ガイド確認を選択し、フロントスピーカー(右側)から確認音が出力されることを確認する。
点検結果は OK か?
OK ≫ NAVI コントロールユニットを交換する
AV - 244
カーウイングス&ハンドフリー電話
1. BCM 自己診断(通信診断)点検
BCM 自己診断(通信診断)を続行し、下記を確認する。
B
故障コード 52 が表示されたか?
NO ≫2へ
2. BCM 自己診断(スイッチモニタ ) 点検 C
ページ ) を参照。
YES ≫ 4 へ
NO ≫3へ
3. ハーネス点検 E
点検結果は OK か?
4. 故障診断画面の起動点検
故障診断画面を起動する。 「 故障診断機能」( AV-59 ページ ) を参照。
H
故障診断画面は起動したか?
AV
AV - 245
カーウイングス&ハンドフリー電話
異常ではない現象例 JKS00C3O
情報サービス関係
症状 原因 処置方法
携帯電話の回線が混雑している。 しばらくしてからかけ直す。
電話の電波が届きづらい位置にいる。 電話の電波が届きやすい地点になると、
接続する。
携帯電話にダイヤルロックがかかってい る。 携帯電話のダイヤルロックを解除する。
携帯電話に発信規制が設定されている。 携帯電話の発信規制を解除する。
例:お父さんのアドレス宛てのメール を、娘の携帯
電話を接続して受信しよう としている。
AV - 246
カーウイングス&ハンドフリー電話
ハンドフリー電話関係
症状 原因・点検方法 A
ビルの谷間などで音声が乱れ る。 電波がビルなどにより乱反射したり、電波がさえぎられる場合がある。
相手に声が伝わらない。 携帯電話と携帯電話接続コネクターは接続されているか。
発信できない。 • 携帯電話と携帯電話接続コネクターは接続されているか。
• 携帯電話がダイヤルロックされていないか。 E
• ダイヤル入力した電話番号は 3 桁以上か。
• 携帯電話の表示部にメッセージは表示されていないか。
• 通信事業者サービス地域外の場合。
• 電波が届きにくい場所にいる場合。
F
ハンドフリー通話時、相手側に ノイズが 携帯電話の置場所によっては相手側にノイズが聞こえることがある。
聞こえる。
AV
AV - 247
カーウイングス&ハンドフリー電話
マイクの取り外し、取り付け JKS00BJ6
取り外し
2. 遮音用ウレタンをはがす。
SKIA2919J
3. マイクを固定している爪( 2 箇所)を外側に広げてマイクを取り外
す。
SKIA2662J
取り付け
取り付けは下記に注意し、取り外しの逆の手順で行う。
注意 : • 取り付け時は、遮音用ウレタンを、マイクを包み込む様にして音が漏れないように貼り付けること。
• 遮音用ウレタンが破損もしくは粘着力が低下していた場合は交換すること。
取り外し
SKIA2999J
AV - 248
カーウイングス&ハンドフリー電話
3. TEL ハーネスコネクターから車両側ハーネスコネクターを外す。
SKIA3000J
リップを外す。
SKIA3001J E
6. TEL ハーネスを取り外す。
SKIA3002J
取り付け
H
取り付けは下記に注意し、取り外しの逆の手順で行う。
注意 : TEL ハーネス取り付け時はカールコードがかみ込まない程度の
長さで、ハーネス固定用ホルダーで固定する。
J
SKIA3003J
AV
AV - 249
カーウイングス&ハンドフリー電話
AV - 250