Sei sulla pagina 1di 97

2CPX208R-V3

4-port multibeam antenna, 4x 790–960 MHz, 2x 38° HPBW, 2x RET with


manual override.
l Integrated Internal Remote Electrical Tilt (RET), with independent control of electrical tilt with manual
override on all arrays

l Single panel design supporting two separate beams perfectly optimized at horizontal pointing angles of
+27 degrees and –27 degrees from boresight

Electrical Specifications
Frequency Band, MHz 790–890 890–960
Gain, dBi 18.1 18.6
Beam Centers, Horizontal, degrees ±27 ±27
Beamwidth, Horizontal, degrees 40 35
Beamwidth, Vertical, degrees 10.0 9.1
Beam Tilt, degrees 0– 10 0– 10
USLS (First Lobe), dB 18 18
Null Fill, dB -22 -22
Front
Front--to
to--Back Ratio at 180°, dB 32 31
Isolation, Same Beam, dB 25 25
VSWR | Return Loss, dB 1.29 | 18.0 1.29 | 18.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150
Input Power per Port, maximum,
300 300
watts
Polarization   ±45° ±45°
Impedance   50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 790–890 890–960
Gain by all Beam Tilts, average, dBi 17.8 18.3
Gain by all Beam Tilts Tolerance,
±0.4 ±0.3
dB
0 ° | 17.9 0 ° | 18.4
Gain by Beam Tilt, average, dBi 5 ° | 17.9 5 ° | 18.4
10 ° | 17.8 10 ° | 18.1
Beamwidth, Horizontal Tolerance,
±2.3 ±2.2
degrees
Beamwidth, Vertical Tolerance,
±0.5 ±0.4
degrees
USLS, beampeak to 20° above
21 22
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
23 20
± 30°, dB
CPR at Boresight, dB 23 21
CPR at Sector, dB 12 7

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

General Specifications

page 1 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
2CPX208R-V3

Operating Frequency Band 790 – 960 MHz


Antenna Type Multibeam
Band Single band
Performance Note Outdoor usage
 

Mechanical Specifications
RF Connector Quantity, total 4
RF Connector Quantity, low band 4
RF Connector Interface 7-16 DIN Female
Color Light gray
Grounding Type RF connector inner conductor and body grounded to reflector and mounting
bracket
Radiator Material Low loss circuit board
Radome Material Polyester fiberglass pultrusion
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 1,352.0 N @ 150 km/h   |   303.9 lbf @ 150 km/h
Wind Loading, lateral 228.0 N @ 150 km/h   |   51.3 lbf @ 150 km/h
Wind Speed, maximum 200 km/h   |   124 mph
 

Dimensions
Length 2090.0 mm   |   82.3 in
Width 504.0 mm   |   19.8 in
Depth 118.0 mm   |   4.6 in
Net Weight, without mounting kit 32.5 kg   |   71.7 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET Low band (2)
Power Consumption, idle state, maximum 2W
Power Consumption, normal conditions, maximum 13 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 1 female   |   1 male
 

Packed Dimensions
Length 2229.0 mm   |   87.8 in
Width 593.0 mm   |   23.3 in
Depth 209.0 mm   |   8.2 in

page 2 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
2CPX208R-V3

Shipping Weight 45.5 kg   |   100.3 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

Included Products
T -029
029--GL
GL--E — Adjustable Tilt Pipe Mounting Kit for 2.0"
2.0"--4.5" (60
(60--115mm) OD round members for panel antennas. Includes 2 clamp sets.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 3 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
2H-33A-R2

4-port multibeam antenna, 4x 1695–2400 MHz, 2x 38° HPBW, 2x RET


l Enhances network capacity through six sectors site application with only three antenna faces

l Maximizes frequency spectrum utilization to increase Average Revenue Per User (ARPU)

l Reduces antenna count to minimize Cap


Cap--Ex and Op
Op--Ex costs

l High gain with excellent sector edge roll


roll--off and azimuth sidelobe suppression

l Each antenna downtilt can be independently adjusted for greater flexibility in network optimization

Electrical Specifications
Frequency Band, MHz 1695–1880 1850–1990 1920–2180 2300–2400
Gain, dBi 19.1 19.6 19.9 19.1
Beam Centers, Horizontal, degrees ±27 ±27 ±27 ±27
Beamwidth, Horizontal, degrees 38 36 34 30
Beamwidth, Vertical, degrees 7.5 7.0 6.5 5.9
Beam Tilt, degrees 2– 12 2– 12 2– 12 2– 12
USLS (First Lobe), dB 20 20 19 18
Front
Front--to
to--Back Ratio at 180°, dB 34 37 37 30
Isolation, Cross Polarization, dB 28 28 28 28
Isolation, Inter
Inter--band, dB 16 16 16 16
VSWR | Return Loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150
Input Power per Port, maximum,
250 250 250 250
watts
Polarization   ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 1695–1880 1850–1990 1920–2180 2300–2400
Gain by all Beam Tilts, average,
18.7 19.3 19.6 18.7
dBi
Gain by all Beam Tilts Tolerance,
±0.5 ±0.4 ±0.6 ±0.6
dB
2 ° | 18.6 2 ° | 19.1 2 ° | 19.5 2 ° | 19.0
Gain by Beam Tilt, average, dBi 7 ° | 18.8 7 ° | 19.4 7 ° | 19.8 7 ° | 18.8
12 ° | 18.6 12 ° | 19.2 12 ° | 19.0 12 ° | 18.3
Beamwidth, Horizontal Tolerance,
±1.3 ±1.3 ±2.2 ±1.7
degrees
Beamwidth, Vertical Tolerance,
±0.4 ±0.3 ±0.5 ±0.2
degrees
USLS, beampeak to 20° above
14 15 15 15
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
28 29 27 24
± 30°, dB
CPR at Boresight, dB 23 24 19 13

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

page 4 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
2H-33A-R2

Array Layout

 
 

General Specifications
Operating Frequency Band 1695 – 2400 MHz
Antenna Type Multibeam
Band Single band
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
 

Mechanical Specifications
RF Connector Quantity, total 4
RF Connector Quantity, high band 4
RF Connector Interface 4.3-10 Female
Color Light gray
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 221.0 N @ 150 km/h   |   49.7 lbf @ 150 km/h
Wind Loading, lateral 185.0 N @ 150 km/h   |   41.6 lbf @ 150 km/h
Wind Loading, maximum 105.4 lbf @ 150 km/h   |   469.0 N @ 150 km/h
Wind Speed, maximum 241 km/h   |   150 mph
 
page 5 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
2H-33A-R2
 

Dimensions
Length 1400.0 mm   |   55.1 in
Width 350.0 mm   |   13.8 in
Depth 208.0 mm   |   8.2 in
Net Weight, without mounting kit 17.6 kg   |   38.8 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (2)
Power Consumption, idle state, maximum 2W
Power Consumption, normal conditions, maximum 13 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 2 female   |   2 male
 

Packed Dimensions
Length 1544.0 mm   |   60.8 in
Width 447.0 mm   |   17.6 in
Depth 354.0 mm   |   13.9 in
Shipping Weight 30.0 kg   |   66.1 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

Included Products
BSAMNT--3 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 6 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
2HH-33A-R4

8-port multibeam antenna, 8x 1695–2400 MHz, 4x 38° HPBW, 4x RET


with retractable tilt rods
l Enhances network capacity through six sectors site application with only three antenna faces

l Maximizes frequency spectrum utilization to increase Average Revenue Per User (ARPU)

l Reduces antenna count to minimize Cap


Cap--Ex and Op
Op--Ex costs

l High gain with excellent sector edge roll


roll--off and azimuth sidelobe suppression

l Each antenna downtilt can be independently adjusted for greater flexibility in network optimization

l Supports re
re--configurable antenna sharing capability enabling control of the internal RET system using
up to two separate RET compatible OEM radios

Electrical Specifications
Frequency Band, MHz 1695–1880 1850–1990 1920–2180 2300–2400
Gain, dBi 19.1 19.7 19.9 19.4
Beam Centers, Horizontal, degrees ±27 ±27 ±27 ±27
Beamwidth, Horizontal, degrees 38 36 33 29
Beamwidth, Vertical, degrees 7.4 7.0 6.6 5.9
Beam Tilt, degrees 2– 12 2– 12 2– 12 2– 12
USLS (First Lobe), dB 19 20 19 17
Front
Front--to
to--Back Ratio at 180°, dB 37 37 35 33
Isolation, Cross Polarization, dB 28 28 28 28
Isolation, Inter
Inter--band, dB 16 16 16 16
VSWR | Return Loss, dB 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150
Input Power per Port at 50°C,
200 200 200 200
maximum, watts
Polarization   ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 1695–1880 1850–1990 1920–2180 2300–2400
Gain by all Beam Tilts, average,
18.7 19.4 19.5 18.9
dBi
Gain by all Beam Tilts Tolerance,
±0.6 ±0.4 ±0.6 ±0.7
dB
2 ° | 18.7 2 ° | 19.2 2 ° | 19.5 2 ° | 19.0
Gain by Beam Tilt, average, dBi 7 ° | 18.8 7 ° | 19.4 7 ° | 19.8 7 ° | 19.0
12 ° | 18.6 12 ° | 19.3 12 ° | 19.1 12 ° | 18.7
Beamwidth, Horizontal Tolerance,
±2 ±1.7 ±3 ±2.9
degrees
Beamwidth, Vertical Tolerance,
±0.4 ±0.3 ±0.5 ±0.3
degrees
USLS, beampeak to 20° above
16 18 17 15
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
29 30 29 25
± 30°, dB
CPR at Boresight, dB 21 22 19 13
CPR at Sector, dB 12 13 11 5

page 7 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2HH-33A-R4

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

Array Layout

 
 

Port Configuration

page 8 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2HH-33A-R4

 
 

General Specifications
Operating Frequency Band 1695 – 2400 MHz
Antenna Type Multibeam
Band Single band
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
Total Input Power, maximum 400 W @ 50 °C
 

Mechanical Specifications
RF Connector Quantity, total 8
RF Connector Quantity, high band 8
RF Connector Interface 4.3-10 Female
Color Light gray
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 557.0 N @ 150 km/h   |   125.7 lbf @ 150 km/h
Wind Loading, lateral 175.0 N @ 150 km/h   |   39.3 lbf @ 150 km/h

page 9 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2HH-33A-R4

Wind Loading, maximum 759.0 N @ 150 km/h   |   170.6 lbf @ 150 km/h


Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 1350.0 mm   |   53.1 in
Width 640.0 mm   |   25.2 in
Depth 235.0 mm   |   9.3 in
Net Weight, without mounting kit 30.8 kg   |   67.9 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (4)
Power Consumption, idle state, maximum 1W
Power Consumption, normal conditions, maximum 8 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Hardware CommRET v2
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 2 female   |   2 male
 

Packed Dimensions
Length 1501.0 mm   |   59.1 in
Width 797.0 mm   |   31.4 in
Depth 402.0 mm   |   15.8 in
Shipping Weight 41.7 kg   |   91.9 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

Included Products
BSAMNT--3 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

page 10 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2HH-33A-R4

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 11 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2HH-38A-R4

8-port multibeam antenna, 8x 1695–2200 MHz, 4x 38° HPBW, 4x RET


l Enhances network capacity through six sectors site application with only three antenna faces

l Maximizes frequency spectrum utilization to increase Average Revenue Per User (ARPU)

l Reduces antenna count to minimize Cap


Cap--Ex and Op
Op--Ex costs

l High gain with excellent sector edge roll


roll--off and azimuth sidelobe suppression

l Each antenna downtilt can be independently adjusted for greater flexibility in network optimization

Electrical Specifications
Frequency Band, MHz 1695–1880 1850–1990 1920–2200
Gain, dBi 19.4 19.8 20.0
Beam Centers, Horizontal, degrees ±27 ±27 ±27
Beamwidth, Horizontal, degrees 38 36 34
Beamwidth, Vertical, degrees 7.6 7.1 6.7
Beam Tilt, degrees 2– 10 2– 10 2– 10
USLS (First Lobe), dB 23 24 24
Front
Front--to
to--Back Ratio at 180°, dB 33 35 33
Isolation, Cross Polarization, dB 30 30 30
VSWR | Return Loss, dB 1.4 | 15.6 1.4 | 15.6 1.4 | 15.6
PIM, 3rd Order, 2 x 20 W, dBc -153 -153 -153
Input Power per Port, maximum,
250 250 250
watts
Polarization   ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 1695–1880 1850–1990 1920–2200
Gain by all Beam Tilts, average, dBi 18.9 19.5 19.6
Gain by all Beam Tilts Tolerance,
±0.5 ±0.3 ±0.6
dB
2 ° | 18.8 2 ° | 19.4 2 ° | 19.8
Gain by Beam Tilt, average, dBi 6 ° | 19.0 6 ° | 19.5 6 ° | 19.7
10 ° | 18.9 10 ° | 19.4 10 ° | 19.3
Beamwidth, Vertical Tolerance,
±0.4 ±0.3 ±0.5
degrees
USLS, beampeak to 20° above
17 18 18
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
28 28 27
± 30°, dB
CPR at Boresight, dB 23 22 17
CPR at Sector, dB 11 13 11

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

Array Layout

page 12 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2HH-38A-R4

 
 

Port Configuration

 
 

General Specifications
Operating Frequency Band 1695 – 2200 MHz

page 13 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2HH-38A-R4

Antenna Type Multibeam


Band Single band
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
 

Mechanical Specifications
RF Connector Quantity, total 8
RF Connector Quantity, high band 8
RF Connector Interface 4.3-10 Female
Color Light gray
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 557.0 N @ 150 km/h   |   125.7 lbf @ 150 km/h
Wind Loading, lateral 175.0 N @ 150 km/h   |   39.3 lbf @ 150 km/h
Wind Loading, maximum 759.0 N @ 150 km/h   |   170.6 lbf @ 150 km/h
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 1350.0 mm   |   53.1 in
Width 640.0 mm   |   25.2 in
Depth 235.0 mm   |   9.3 in
Net Weight, without mounting kit 31.2 kg   |   68.8 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (4)
Power Consumption, idle state, maximum 2W
Power Consumption, normal conditions, maximum 13 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 1 female   |   1 male
 

Packed Dimensions
Length 1501.0 mm   |   59.1 in
Width 797.0 mm   |   31.4 in
Depth 402.0 mm   |   15.8 in

page 14 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2HH-38A-R4

Shipping Weight 47.7 kg   |   105.2 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

Included Products
BSAMNT--3 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 15 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2HH-38A-R4-V2

8-port multibeam antenna, 8x 1695–2200 MHz, 4x 38° HPBW, 4x RET


l Enhances network capacity through six sectors site application with only three antenna faces

l Maximizes frequency spectrum utilization to increase Average Revenue Per User (ARPU)

l Reduces antenna count to minimize Cap


Cap--Ex and Op
Op--Ex costs

l High gain with excellent sector edge roll


roll--off and azimuth sidelobe suppression

l Each antenna downtilt can be independently adjusted for greater flexibility in network optimization

Electrical Specifications
Frequency Band, MHz 1695–1880 1850–1990 1920–2200
Gain, dBi 19.3 19.7 20.0
Beam Centers, Horizontal, degrees ±27 ±27 ±27
Beamwidth, Horizontal, degrees 38 36 34
Beamwidth, Vertical, degrees 7.7 7.3 6.8
Beam Tilt, degrees 2– 10 2– 10 2– 10
Horizontal Sidelobe, dB 24 24 23
USLS (First Lobe), dB 24 24 24
Front
Front--to
to--Back Ratio at 180°, dB 36 36 34
Isolation, Cross Polarization, dB 30 30 30
Isolation, Inter
Inter--band, dB 17 17 17
VSWR | Return Loss, dB 1.43 | 15.0 1.43 | 15.0 1.43 | 15.0
PIM, 3rd Order, 2 x 20 W, dBc -153 -153 -153
Input Power per Port at 50°C,
200 200 200
maximum, watts
Polarization   ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 1695–1880 1850–1990 1920–2200
Gain by all Beam Tilts, average, dBi 18.9 19.4 19.6
Gain by all Beam Tilts Tolerance,
±0.5 ±0.4 ±0.7
dB
2 ° | 18.8 2 ° | 19.3 2 ° | 19.8
Gain by Beam Tilt, average, dBi 6 ° | 19.0 6 ° | 19.5 6 ° | 19.7
10 ° | 18.9 10 ° | 19.4 10 ° | 19.2
Beamwidth, Horizontal Tolerance,
±1.6 ±1.7 ±3.2
degrees
Beamwidth, Vertical Tolerance,
±0.4 ±0.3 ±0.6
degrees
USLS, beampeak to 20° above
18 19 19
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
28 29 28
± 30°, dB
CPR at Boresight, dB 21 22 21
CPR at Sector, dB 11 13 12

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

page 16 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2HH-38A-R4-V2

Array Layout

 
 

Port Configuration

 
 

page 17 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2HH-38A-R4-V2

General Specifications
Operating Frequency Band 1695 – 2200 MHz
Antenna Type Multibeam
Band Single band
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
Total Input Power, maximum 900 W @ 50 °C
 

Mechanical Specifications
RF Connector Quantity, total 8
RF Connector Quantity, high band 8
RF Connector Interface 4.3-10 Female
Color Light gray
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 505.0 N @ 150 km/h   |   114.4 lbf @ 150 km/h
Wind Loading, lateral 156.0 N @ 150 km/h   |   35.1 lbf @ 150 km/h
Wind Loading, maximum 688.0 N @ 150 km/h   |   154.7 lbf @ 150 km/h
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 1224.0 mm   |   48.2 in
Width 640.0 mm   |   25.2 in
Depth 235.0 mm   |   9.3 in
Net Weight, without mounting kit 29.7 kg   |   65.5 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (4)
Power Consumption, idle state, maximum 1W
Power Consumption, normal conditions, maximum 10 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 1 female   |   1 male
 

page 18 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2HH-38A-R4-V2

Packed Dimensions
Length 1375.0 mm   |   54.1 in
Width 797.0 mm   |   31.4 in
Depth 402.0 mm   |   15.8 in
Shipping Weight 45.6 kg   |   100.5 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

Included Products
BSAMNT--3 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 19 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2UNPX203.6R2

8-port multibeam antenna, 4x 698–894 and 4x 1710-2170 MHz, 4x 37°


HPBW, 4x RET
l Single panel design supporting two separate beams perfectly optimized at horizontal pointing angles of
+27 degrees and –27 degrees from boresight

Electrical Specifications
Frequency Band, MHz 698–790 790–894 1710–1920 1920–2170
Gain, dBi 13.8 14.5 16.2 17.5
Beam Centers, Horizontal, degrees ±28 ±28 ±30 ±30
Beamwidth, Horizontal, degrees 43 37 35 32
Beamwidth, Vertical, degrees 25.1 21.7 12.1 11.0
Beam Tilt, degrees 1– 16 1– 16 0– 10 0– 10
USLS (First Lobe), dB 15 15 15 15
Front
Front--to
to--Back Ratio at 180°, dB 20 20 30 30
Isolation, Cross Polarization, dB 22 22 20 20
VSWR | Return Loss, dB 1.43 | 15.0 1.43 | 15.0 1.43 | 15.0 1.43 | 15.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150
Input Power per Port, maximum,
500 500 300 300
watts
Polarization   ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 698–790 790–894 1710–1920 1920–2170
Gain by all Beam Tilts, average,
13.7 14.3 15.7 16.0
dBi
Gain by all Beam Tilts Tolerance,
±0.6 ±0.9 ±0.6 ±0.5
dB
1 ° | 13.7 1 ° | 14.6 0 ° | 15.7 0 ° | 16.0
Gain by Beam Tilt, average, dBi 8 ° | 13.8 8 ° | 14.4 5 ° | 15.7 5 ° | 16.0
16 ° | 13.5 16 ° | 13.7 10 ° | 15.6 10 ° | 15.8
Beamwidth, Horizontal Tolerance,
±2 ±3.6 ±2.5 ±3.1
degrees
Beamwidth, Vertical Tolerance,
±1.7 ±1.6 ±0.7 ±0.9
degrees
USLS, beampeak to 20° above
18 16 15 15
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
21 17 31 31
± 30°, dB

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

page 20 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
2UNPX203.6R2

General Specifications
Operating Frequency Band 1710 – 2170 MHz   |   698 – 894 MHz
Antenna Type Multibeam
Band Multiband
Performance Note Outdoor usage
 

Mechanical Specifications
RF Connector Quantity, total 8
RF Connector Quantity, low band 4
RF Connector Quantity, high band 4
RF Connector Interface 7-16 DIN Female
Color Light gray
Grounding Type RF connector inner conductor and body grounded to reflector and mounting
bracket
Radiator Material Aluminum   |   Low loss circuit board
Radome Material Polyester fiberglass pultrusion
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 1,258.0 N @ 150 km/h   |   282.8 lbf @ 150 km/h
Wind Loading, lateral 194.0 N @ 150 km/h   |   43.6 lbf @ 150 km/h
Wind Speed, maximum 250 km/h   |   155 mph
 

Dimensions
Length 1746.0 mm   |   68.7 in
Width 565.0 mm   |   22.2 in
Depth 127.0 mm   |   5.0 in
Net Weight, without mounting kit 37.0 kg   |   81.6 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (2)   |   Low band (2)
Power Consumption, idle state, maximum 2W
Power Consumption, normal conditions, maximum 13 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Interface 8-pin DIN Male
RET Interface, quantity 2 male
 

Packed Dimensions

page 21 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
2UNPX203.6R2

Length 1940.0 mm   |   76.4 in


Width 625.0 mm   |   24.6 in
Depth 270.0 mm   |   10.6 in
Shipping Weight 43.0 kg   |   94.8 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

Included Products
T -029
029--GL
GL--E — Adjustable Tilt Pipe Mounting Kit for 2.0"
2.0"--4.5" (60
(60--115mm) OD round members for panel antennas. Includes 2 clamp sets.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 22 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
2UNPX206.12R2

8-port multibeam antenna, 4x 698–894 and 4x 1710-2180 MHz, 4x 35°


HPBW, 4x RET
l Antenna has individual AISG connectors per band: One in/out pair for low band in cascaded single
single--RET
configuration to independently control the two low band beams; one in/out pair for high band in
cascaded single
single--RET configuration to independently control the two high band beams

Electrical Specifications
Frequency Band, MHz 698–806 806–894 1710–1880 1850–1990 1920–2180
Gain, dBi 14.9 15.5 17.6 18.6 18.6
Beam Centers, Horizontal, degrees ±29 ±25 ±32 ±30 ±28
Beamwidth, Horizontal, degrees 40 35 34 31 31
Beamwidth, Vertical, degrees 15.6 13.5 6.9 6.5 6.2
Beam Tilt, degrees 0– 10 0– 10 0– 10 0– 10 0– 10
USLS (First Lobe), dB 17 14 18 18 18
Front
Front--to
to--Back Ratio at 180°, dB 24 24 35 40 39
Isolation, Same Beam, dB 25 25 25 25 25
Isolation, Beam to Beam, dB 18 18 18 18 18
VSWR | Return Loss, dB 1.43 | 15.0 1.43 | 15.0 1.43 | 15.0 1.43 | 15.0 1.43 | 15.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150
Input Power per Port, maximum,
300 300 250 250 250
watts
Polarization   ±45° ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 698–806 806–894 1710–1880 1850–1990 1920–2180
Gain by all Beam Tilts, average, dBi 14.7 15.1 17.4 18.2 18.4
Gain by all Beam Tilts Tolerance,
±0.6 ±0.7 ±0.6 ±0.6 ±0.8
dB
0 ° | 14.7 0 ° | 15.2 0 ° | 17.5 0 ° | 18.2 0 ° | 18.5
Gain by Beam Tilt, average, dBi 5 ° | 14.7 5 ° | 15.1 5 ° | 17.4 5 ° | 18.2 5 ° | 18.5
10 ° | 14.6 10 ° | 14.9 10 ° | 17.3 10 ° | 18.1 10 ° | 18.1
Beamwidth, Horizontal Tolerance,
±2 ±2.7 ±2.8 ±1.6 ±1.2
degrees
Beamwidth, Vertical Tolerance,
±1.1 ±0.9 ±0.4 ±0.2 ±0.4
degrees
USLS, beampeak to 20° above
18 16 17 18 18
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
21 20 30 35 34
± 30°, dB
CPR at Boresight, dB 19 18 22 22 18

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

General Specifications
Operating Frequency Band 1710 – 2180 MHz   |   698 – 894 MHz

page 23 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
2UNPX206.12R2

Antenna Type Multibeam


Band Multiband
Performance Note Outdoor usage
 

Mechanical Specifications
RF Connector Quantity, total 8
RF Connector Quantity, low band 4
RF Connector Quantity, high band 4
RF Connector Interface 7-16 DIN Female
Color Gray
Grounding Type RF connector inner conductor and body grounded to reflector and mounting
bracket
Radiator Material Aluminum   |   Low loss circuit board
Radome Material ASA, UV stabilized
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 1,473.0 N @ 150 km/h   |   331.1 lbf @ 150 km/h
Wind Loading, lateral 256.0 N @ 150 km/h   |   57.6 lbf @ 150 km/h
Wind Speed, maximum 200 km/h   |   124 mph
 

Dimensions
Length 1728.0 mm   |   68.0 in
Width 684.0 mm   |   26.9 in
Depth 245.0 mm   |   9.6 in
Net Weight, without mounting kit 44.0 kg   |   97.0 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (2)   |   Low band (2)
Power Consumption, idle state, maximum 2W
Power Consumption, normal conditions, maximum 13 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 2 female   |   2 male
 

Packed Dimensions
Length 1932.0 mm   |   76.1 in
Width 787.0 mm   |   31.0 in
Depth 347.0 mm   |   13.7 in

page 24 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
2UNPX206.12R2

Shipping Weight 69.0 kg   |   152.1 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

Included Products
T -041
041--GL
GL--E — Adjustable Tilt Pipe Mounting Kit for 2.0"
2.0"--4.5" (60
(60--115mm) OD round members for panel antennas. Includes 2 clamp sets.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 25 of 25
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
2UPX210B-T2

4-port multibeam antenna, 4x 694–896 MHz, 2x 37° HPBW, 2x RET with


manual override.
l Integrated Internal Remote Electrical Tilt (RET), with independent control of electrical tilt with manual
override on both beams

l Each port has an integrated bias tee, and each beam has its own smart switch that automatically selects
between bias tee or AISG inputs according to a predetermined priority table

l Single panel design supporting two separate beams perfectly optimized at horizontal pointing angles of
+27 degrees and –27 degrees from boresight

Electrical Specifications
Frequency Band, MHz 694–806 806–896
Gain, dBi 17.9 18.7
Beam Centers, Horizontal, degrees ±27 ±27
Beamwidth, Horizontal, degrees 39 36
Beamwidth, Vertical, degrees 9.6 8.4
Beam Tilt, degrees 0– 10 0– 10
USLS (First Lobe), dB 21 21
Front
Front--to
to--Back Ratio at 180°, dB 34 40
Isolation, Cross Polarization, dB 25 25
Isolation, Inter
Inter--band, dB 18 18
VSWR | Return Loss, dB 1.43 | 15.0 1.43 | 15.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150
Input Power per Port at 50°C,
200 200
maximum, watts
Polarization   ±45° ±45°
Impedance   50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 694–806 806–896
Gain by all Beam Tilts, average, dBi 17.6 18.5
Gain by all Beam Tilts Tolerance,
±0.6 ±0.3
dB
0 ° | 17.6 0 ° | 18.5
Gain by Beam Tilt, average, dBi 5 ° | 17.6 5 ° | 18.5
10 ° | 17.6 10 ° | 18.4
Beamwidth, Horizontal Tolerance,
±1.8 ±1.6
degrees
Beamwidth, Vertical Tolerance,
±0.7 ±0.4
degrees
USLS, beampeak to 20° above
21 19
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
25 29
± 30°, dB
CPR at Boresight, dB 20 19

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

page 1 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2UPX210B-T2

General Specifications
Operating Frequency Band 694 – 896 MHz
Antenna Type Multibeam
Band Single band
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel
measurements described in white paper WP-112534-EN
Total Input Power, maximum 700 W @ 50 °C
 

Mechanical Specifications
RF Connector Quantity, total 4
RF Connector Quantity, low band 4
RF Connector Interface 7-16 DIN Female
Grounding Type RF connector body grounded to reflector and mounting bracket
Radiator Material Copper   |   Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 1,102.0 N @ 150 km/h   |   247.7 lbf @ 150 km/h
Wind Loading, lateral 372.0 N @ 150 km/h   |   83.6 lbf @ 150 km/h
Wind Loading, maximum 1,497.0 N @ 150 km/h   |   336.5 lbf @ 150 km/h
Wind Speed, maximum 200 km/h   |   124 mph
 

Dimensions
Length 2533.0 mm   |   99.7 in
Width 640.0 mm   |   25.2 in
Depth 235.0 mm   |   9.3 in
Net Weight, without mounting kit 47.0 kg   |   103.6 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal Bias Tee Port 1   |   Port 2   |   Port 3   |   Port 4
Internal RET Low band (2)
Power Consumption, idle state, maximum 2W
Power Consumption, normal conditions, maximum 13 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 1 female   |   2 male
 

page 2 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2UPX210B-T2

Packed Dimensions
Length 2684.0 mm   |   105.7 in
Width 797.0 mm   |   31.4 in
Depth 402.0 mm   |   15.8 in
Shipping Weight 67.0 kg   |   147.7 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU  
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

Included Products
T -029
029--GL
GL--E — Adjustable Tilt Pipe Mounting Kit for 2.0"
2.0"--4.5" (60
(60--115mm) OD round members for panel antennas. Includes 2 clamp sets.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 3 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
2VV-33C-R4

8-port multibeam antenna, 8x 1695–2690 MHz, 4x 33° HPBW, 4x RET


l Enhances network capacity and spectrum utilization when used in six sector applications

l Reduces antenna count to minimize Cap


Cap--Ex and Op
Op--Ex costs – 3 antennas required for 6 sector
configurations

Electrical Specifications
Frequency Band, MHz 1695–1880 1850–1990 1920–2180 2300–2400 2490–2690
Gain, dBi 18.4 19.0 19.4 19.8 20.2
Beam Centers, Horizontal, degrees ±27 ±27 ±27 ±27 ±27
Beamwidth, Horizontal, degrees 39 37 36 34 29
Beamwidth, Vertical, degrees 7.9 7.4 6.9 6.2 5.6
Beam Tilt, degrees 2– 12 2– 12 2– 12 2– 12 2– 12
USLS (First Lobe), dB 16 16 16 20 19
Front
Front--to
to--Back Ratio at 180°, dB 32 33 33 33 31
Isolation, Cross Polarization, dB 25 25 25 25 25
Isolation, Beam to Beam, dB 28 28 28 28 28
VSWR | Return Loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150
Input Power per Port at 50°C,
200 200 200 200 200
maximum, watts
Polarization   ±45° ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 1695–1880 1850–1990 1920–2180 2300–2400 2490–2690
Gain by all Beam Tilts, average, dBi 17.8 18.6 18.8 19.4 19.7
Gain by all Beam Tilts Tolerance,
±0.9 ±0.6 ±0.5 ±0.6 ±0.7
dB
2 ° | 17.7 2 ° | 18.3 2 ° | 18.6 2 ° | 19.1 2 ° | 19.4
Gain by Beam Tilt, average, dBi 7 ° | 17.9 7 ° | 18.7 7 ° | 19.0 7 ° | 19.5 7 ° | 19.9
12 ° | 17.7 12 ° | 18.5 12 ° | 18.7 12 ° | 19.3 12 ° | 19.4
Beamwidth, Horizontal Tolerance,
±1.9 ±2.1 ±2.2 ±3.9 ±1.1
degrees
Beamwidth, Vertical Tolerance,
±0.6 ±0.3 ±0.5 ±0.3 ±0.3
degrees
USLS, beampeak to 20° above
15 16 16 17 16
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
23 25 25 27 25
± 30°, dB
CPR at Boresight, dB 21 23 24 20 27
CPR at 10 dB Horizontal
11 16 16 14 10
Beamwidth, dB

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

Array Layout
page 4 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
2VV-33C-R4

 
 

Port Configuration

 
 

General Specifications
Operating Frequency Band 1695 – 2690 MHz

page 5 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
2VV-33C-R4

Antenna Type Multibeam


Band Single band
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
Total Input Power, maximum 1,200 W @ 50 °C
 

Mechanical Specifications
RF Connector Quantity, total 8
RF Connector Quantity, high band 8
RF Connector Interface 4.3-10 Female
Color Light gray
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Low loss circuit board
Radome Material Fiberglass, UV resistant
RF Connector Location Bottom
Wind Loading, frontal 525.0 N @ 150 km/h   |   118.7 lbf @ 150 km/h
Wind Loading, lateral 386.0 N @ 150 km/h   |   86.8 lbf @ 150 km/h
Wind Loading, maximum 898.0 N @ 150 km/h   |   201.9 lbf @ 150 km/h
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 2499.0 mm   |   98.4 in
Width 395.0 mm   |   15.6 in
Depth 228.0 mm   |   9.0 in
Net Weight, without mounting kit 36.0 kg   |   79.4 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (4)
Power Consumption, idle state, maximum 1W
Power Consumption, normal conditions, maximum 8 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Hardware CommRET v2
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 2 female   |   2 male
 

Packed Dimensions
Length 2631.0 mm   |   103.6 in
Width 505.0 mm   |   19.9 in

page 6 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
2VV-33C-R4

Depth 386.0 mm   |   15.2 in


Shipping Weight 51.8 kg   |   114.2 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

Included Products
BSAMNT--4 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 7 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
2VV-33C-R4-V3

8-port multibeam antenna, 8x 1695–2690 MHz, 4x 33° HPBW, 4x RET


l Enhances network capacity and spectrum utilization when used in six sector applications

l Reduces antenna count to minimize Cap


Cap--Ex and Op
Op--Ex costs – 3 antennas required for 6 sector
configurations

Electrical Specifications
Frequency Band, MHz 1695–1880 1850–1990 1920–2180 2300–2400 2490–2690
Gain, dBi 18.4 19.0 19.4 19.8 20.2
Beam Centers, Horizontal, degrees ±27 ±27 ±27 ±27 ±27
Beamwidth, Horizontal, degrees 39 37 36 34 29
Beamwidth, Vertical, degrees 7.9 7.4 6.9 6.2 5.6
Beam Tilt, degrees 2– 12 2– 12 2– 12 2– 12 2– 12
USLS (First Lobe), dB 16 16 16 20 19
Front
Front--to
to--Back Ratio at 180°, dB 32 33 33 33 31
Isolation, Cross Polarization, dB 25 25 25 25 25
Isolation, Beam to Beam, dB 28 28 28 28 28
VSWR | Return Loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -153 -153 -153 -153 -153
Input Power per Port at 50°C,
200 200 200 200 200
maximum, watts
Polarization   ±45° ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 1695–1880 1850–1990 1920–2180 2300–2400 2490–2690
Gain by all Beam Tilts, average, dBi 17.8 18.6 18.8 19.4 19.7
Gain by all Beam Tilts Tolerance,
±0.9 ±0.6 ±0.5 ±0.6 ±0.7
dB
2 ° | 17.7 2 ° | 18.3 2 ° | 18.6 2 ° | 19.1 2 ° | 19.4
Gain by Beam Tilt, average, dBi 7 ° | 17.9 7 ° | 18.7 7 ° | 19.0 7 ° | 19.5 7 ° | 19.9
12 ° | 17.7 12 ° | 18.5 12 ° | 18.7 12 ° | 19.3 12 ° | 19.4
Beamwidth, Horizontal Tolerance,
±1.9 ±2.1 ±2.2 ±3.9 ±1.1
degrees
Beamwidth, Vertical Tolerance,
±0.6 ±0.3 ±0.5 ±0.3 ±0.3
degrees
USLS, beampeak to 20° above
15 16 16 17 16
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
23 25 25 27 25
± 30°, dB
CPR at Boresight, dB 21 23 24 20 27
CPR at 10 dB Horizontal
11 16 16 14 10
Beamwidth, dB

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

Array Layout
page 8 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
2VV-33C-R4-V3

 
 

Port Configuration

 
 

General Specifications
Operating Frequency Band 1695 – 2690 MHz

page 9 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
2VV-33C-R4-V3

Antenna Type Multibeam


Band Single band
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
Total Input Power, maximum 1,200 W @ 50 °C
 

Mechanical Specifications
RF Connector Quantity, total 8
RF Connector Quantity, high band 8
RF Connector Interface 4.3-10 Female
Color Light gray
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Low loss circuit board
Radome Material Fiberglass, UV resistant
RF Connector Location Bottom
Wind Loading, frontal 525.0 N @ 150 km/h   |   118.7 lbf @ 150 km/h
Wind Loading, lateral 386.0 N @ 150 km/h   |   86.8 lbf @ 150 km/h
Wind Loading, maximum 898.0 N @ 150 km/h   |   199.9 lbf @ 150 km/h
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 2499.0 mm   |   98.4 in
Width 395.0 mm   |   15.6 in
Depth 228.0 mm   |   9.0 in
Net Weight, without mounting kit 36.0 kg   |   79.4 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (4)
Power Consumption, idle state, maximum 1W
Power Consumption, normal conditions, maximum 8 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Hardware CommRET v2
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 2 female   |   2 male
 

Packed Dimensions
Length 2631.0 mm   |   103.6 in
Width 505.0 mm   |   19.9 in

page 10 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
2VV-33C-R4-V3

Depth 386.0 mm   |   15.2 in


Shipping Weight 51.8 kg   |   114.2 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

Included Products
BSAMNT--4 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 11 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
2VV-33C-R4-V4

8-port multibeam antenna, 8x 1695–2690 MHz, 4x 33° HPBW, 4x RET


l Enhances network capacity and spectrum utilization when used in six sector applications

l Reduces antenna count to minimize Cap


Cap--Ex and Op
Op--Ex costs – 3 antennas required for 6 sector
configurations

Electrical Specifications
Frequency Band, MHz 1695–1880 1850–1990 1920–2180 2300–2400 2490–2690
Gain, dBi 18.4 19.0 19.4 19.8 20.2
Beam Centers, Horizontal, degrees ±27 ±27 ±27 ±27 ±27
Beamwidth, Horizontal, degrees 39 37 36 34 29
Beamwidth, Vertical, degrees 7.9 7.4 6.9 6.2 5.6
Beam Tilt, degrees 2– 12 2– 12 2– 12 2– 12 2– 12
USLS (First Lobe), dB 16 16 16 20 19
Front
Front--to
to--Back Ratio at 180°, dB 32 33 33 33 31
Isolation, Cross Polarization, dB 25 25 25 25 25
Isolation, Beam to Beam, dB 28 28 28 28 28
VSWR | Return Loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -153 -153 -153 -153 -153
Input Power per Port at 50°C,
200 200 200 200 200
maximum, watts
Polarization   ±45° ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 1695–1880 1850–1990 1920–2180 2300–2400 2490–2690
Gain by all Beam Tilts, average, dBi 17.8 18.6 18.8 19.4 19.7
Gain by all Beam Tilts Tolerance,
±0.9 ±0.6 ±0.5 ±0.6 ±0.7
dB
2 ° | 17.7 2 ° | 18.3 2 ° | 18.6 2 ° | 19.1 2 ° | 19.4
Gain by Beam Tilt, average, dBi 7 ° | 17.9 7 ° | 18.7 7 ° | 19.0 7 ° | 19.5 7 ° | 19.9
12 ° | 17.7 12 ° | 18.5 12 ° | 18.7 12 ° | 19.3 12 ° | 19.4
Beamwidth, Horizontal Tolerance,
±1.9 ±2.1 ±2.2 ±3.9 ±1.1
degrees
Beamwidth, Vertical Tolerance,
±0.6 ±0.3 ±0.5 ±0.3 ±0.3
degrees
USLS, beampeak to 20° above
15 16 16 17 16
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
23 25 25 27 25
± 30°, dB
CPR at Boresight, dB 21 23 24 20 27
CPR at 10 dB Horizontal
11 16 16 14 10
Beamwidth, dB

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

Array Layout
page 12 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
2VV-33C-R4-V4

 
 

Port Configuration

 
 

General Specifications
Operating Frequency Band 1695 – 2690 MHz

page 13 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
2VV-33C-R4-V4

Antenna Type Multibeam


Band Single band
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
Total Input Power, maximum 1,200 W @ 50 °C
 

Mechanical Specifications
RF Connector Quantity, total 8
RF Connector Quantity, high band 8
RF Connector Interface 7-16 DIN Female
Color Light gray
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Low loss circuit board
Radome Material Fiberglass, UV resistant
RF Connector Location Bottom
Wind Loading, frontal 525.0 N @ 150 km/h   |   118.7 lbf @ 150 km/h
Wind Loading, lateral 386.0 N @ 150 km/h   |   86.8 lbf @ 150 km/h
Wind Loading, maximum 898.0 N @ 150 km/h   |   199.9 lbf @ 150 km/h
Effective Projected Area (EPA), frontal 0.49 m²   |   5.27 ft²
Effective Projected Area (EPA), lateral 0.36 m²   |   3.88 ft²
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 2499.0 mm   |   98.4 in
Width 395.0 mm   |   15.6 in
Depth 228.0 mm   |   9.0 in
Net Weight, without mounting kit 36.8 kg   |   81.1 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (4)
Power Consumption, idle state, maximum 1W
Power Consumption, normal conditions, maximum 8 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Hardware CommRET v2
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 2 female   |   2 male
 

Packed Dimensions
page 14 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
2VV-33C-R4-V4

Length 2631.0 mm   |   103.6 in


Width 505.0 mm   |   19.9 in
Depth 386.0 mm   |   15.2 in
Shipping Weight 52.6 kg   |   116.0 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

Included Products
BSAMNT--4 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 15 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
2x9NPA2010F

18-port multibeam antenna, 18x 1710–2170 MHz, 2x9 Beam Panel


Antenna for Event Coverage. Two rows of beams spaced 8° in elevation.
One set of beams 4° up (+45°) and one set of beams 4° down(-45°) and 5°
in azimuth. Upper and lower beam sets displaced in azimuth by ± 2.5° from
boresight.
Electrical Specifications
Frequency Band, MHz 1710–1920 1920–2170
Gain, dBi 25.0 27.0
Beamwidth, Horizontal, degrees 6 5
Beamwidth, Vertical, degrees 7.2 5.8
USLS (First Lobe), dB 18 18
Front
Front--to
to--Back Ratio at 180°, dB 30 30
Isolation, Cross Polarization, dB 16 16
VSWR | Return Loss, dB 1.43 | 15.0 1.43 | 15.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150
Input Power per Port, maximum,
300 300
watts
Polarization   Single Slant Polarization Single Slant Polarization
Impedance   50 ohm 50 ohm

General Specifications
Operating Frequency Band 1710 – 2170 MHz
Antenna Type Multibeam
Band Single band
Performance Note Outdoor usage
 

Mechanical Specifications
RF Connector Quantity, total 18
RF Connector Quantity, high band 18
RF Connector Interface 7-16 DIN Female
Color Light gray
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radome Material ASA, UV stabilized
RF Connector Location Bottom
Wind Loading, frontal 3,222.0 N @ 150 km/h   |   67.7 lbf @ 150 km/h
Wind Loading, lateral 174.0 N @ 150 km/h   |   39.1 lbf @ 150 km/h
Wind Speed, maximum 160 km/h   |   99 mph
 

Dimensions
Length 1771.0 mm   |   69.7 in
Width 1486.0 mm   |   58.5 in

page 16 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
2x9NPA2010F

Depth 283.0 mm   |   11.1 in


Net Weight, without mounting kit 140.0 kg   |   308.6 lb
 

Packed Dimensions
Length 1998.0 mm   |   78.7 in
Width 1758.0 mm   |   69.2 in
Depth 640.0 mm   |   25.2 in
Shipping Weight 188.0 kg   |   414.5 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

Included Products
T -041
041--GL
GL--E — Adjustable Tilt Pipe Mounting Kit for 2.0"
2.0"--4.5" (60
(60--115mm) OD round members for panel antennas. Includes 2 clamp sets.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 17 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
5NPX1006F

10-port multibeam antenna, 10x 1710–2180 MHz, 5x 10-14° HPBW, fixed


electrical tilt

Electrical Specifications
Frequency Band, MHz 1710–1920 1920–2180
Gain, dBi 21.7 22.3
Beamwidth, Horizontal, degrees 13 12
Beamwidth, Vertical, degrees 11.9 10.9
Beam Tilt, degrees 6 6
USLS (First Lobe), dB 14 16
Front
Front--to
to--Back Ratio at 180°, dB 32 34
CPR at Boresight, dB 10 10
Isolation, Same Beam, dB 25 25
VSWR | Return Loss, dB 1.43 | 15.0 1.43 | 15.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150
Input Power per Port, maximum,
300 300
watts
Polarization   ±45° ±45°
Impedance   50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 1710–1920 1920–2180
Gain by all Beam Tilts, average, dBi 20.7 21.3
Gain by all Beam Tilts Tolerance,
±2 ±1.7
dB
Beamwidth, Horizontal Tolerance,
±2.1 ±1.7
degrees
Beamwidth, Vertical Tolerance,
±0.7 ±0.7
degrees
USLS, beampeak to 20° above
17 18
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
30 32
± 30°, dB
CPR at Boresight, dB 9 10

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

General Specifications
Operating Frequency Band 1710 – 2180 MHz
Antenna Type Multibeam
Band Single band
Performance Note Outdoor usage
 
page 18 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 11, 2019
5NPX1006F
 

Mechanical Specifications
RF Connector Quantity, total 10
RF Connector Quantity, high band 10
RF Connector Interface 7-16 DIN Female
Color Gray
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Brass   |   Low loss circuit board
Radome Material ASA, UV stabilized
Reflector Material Aluminum
RF Connector Location Bottom
Wind Speed, maximum 250 km/h   |   155 mph
 

Dimensions
Length 889.0 mm   |   35.0 in
Width 864.0 mm   |   34.0 in
Depth 202.0 mm   |   8.0 in
Net Weight, without mounting kit 30.0 kg   |   66.1 lb
 

Packed Dimensions
Length 1038.0 mm   |   40.9 in
Width 977.0 mm   |   38.5 in
Depth 349.0 mm   |   13.7 in
Shipping Weight 47.0 kg   |   103.6 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Below Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

Included Products
T -045
045--GL
GL--E — Adjustable Tilt Pipe Mounting Kit for 2.0"
2.0"--4.5" (60
(60--115mm) OD round members for panel antennas. Includes 2 clamp sets.

page 19 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 11, 2019
5NPX1006F

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 20 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 11, 2019
5UPX0805F

10-port multibeam antenna, 10x 698–894 MHz, 5 x 13.5° HPBW, fixed


electrical tilt. Ships with two T-041-GL-E mounting kits.
Electrical Specifications
Frequency Band, MHz 698–894
Gain, dBi 20.6
Beamwidth, Horizontal, degrees 13
Beamwidth, Vertical, degrees 17.1
Beam Tilt, degrees 6
USLS (First Lobe), dB 18
Front
Front--to
to--Back Ratio at 180°, dB 35
CPR at Boresight, dB 12
Isolation, Cross Polarization, dB 25
VSWR | Return Loss, dB 1.43 | 15.0
PIM, 3rd Order, 2 x 20 W, dBc -150
Input Power per Port, maximum,
300
watts
Polarization   ±45°
Impedance   50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 698–894
Gain by all Beam Tilts, average, dBi 19.6
Gain by all Beam Tilts Tolerance,
±1.9
dB
Beamwidth, Horizontal Tolerance,
±2.4
degrees
Beamwidth, Vertical Tolerance,
±3.4
degrees
USLS, beampeak to 20° above
17
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
33
± 30°, dB
CPR at Boresight, dB 12

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

General Specifications
Operating Frequency Band 698 – 894 MHz
Antenna Type Multibeam
Band Single band
Performance Note Outdoor usage
 

Mechanical Specifications
RF Connector Quantity, total 10
RF Connector Quantity, low band 10

page 21 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
5UPX0805F

RF Connector Interface 7-16 DIN Female


Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radome Material Polyester fiberglass pultrusion
RF Connector Location Bottom
Wind Loading, maximum 2,700.0 N @ 160 km/h   |   607.0 lbf @ 160 km/h
Wind Speed, maximum 140 km/h   |   87 mph
 

Dimensions
Length 1617.0 mm   |   63.7 in
Width 1574.0 mm   |   62.0 in
Depth 282.0 mm   |   11.1 in
Net Weight, without mounting kit 85.0 kg   |   187.4 lb
 

Packed Dimensions
Length 1760.0 mm   |   69.3 in
Width 1670.0 mm   |   65.7 in
Depth 440.0 mm   |   17.3 in
Shipping Weight 169.0 kg   |   372.6 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

Included Products
T -041
041--GL
GL--E — Adjustable Tilt Pipe Mounting Kit for 2.0"
2.0"--4.5" (60
(60--115mm) OD round members for panel antennas. Includes 2 clamp sets.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 22 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
T-029-GL-E

Adjustable Tilt Pipe Mounting Kit for 2.0"-4.5" (60-115mm) OD round


members for panel antennas. Includes 2 clamp sets.

General Specifications
Application Outdoor
Includes Brackets   |   Hardware
Package Quantity 1
 

Mechanical Specifications
Color Silver
Material Type Galvanized steel
Mechanical Tilt 0°–8°
 

Dimensions
Antenna-to-Pipe Distance 85.0 mm   |   3.3 in
Bracket-to-Bracket Distance 1400.0 mm   |   55.1 in
Compatible Diameter, maximum 115.0 mm   |   4.5 in
Compatible Diameter, minimum 60.0 mm   |   2.4 in
Compatible Length, maximum 2850.0 mm   |   112.2 in
Compatible Length, minimum 1500.0 mm   |   59.1 in
Net Weight 6.0 kg   |   13.2 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

page 23 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: May 28, 2019
BSAMNT-4

Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD
round members. Kit contains one scissor top bracket set and one bottom
bracket set.

General Specifications
Application Outdoor
Includes Brackets   |   Hardware
Package Quantity 1
 

Mechanical Specifications
Color Silver
Material Type Galvanized steel
 

Dimensions
Compatible Diameter, maximum 114.3 mm   |   4.5 in
Compatible Diameter, minimum 61.0 mm   |   2.4 in
Net Weight 6.6 kg   |   14.6 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

page 24 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: November 17, 2019
T-041-GL-E

Adjustable Tilt Pipe Mounting Kit for 2.0"-4.5" (60-115mm) OD round


members for panel antennas. Includes 2 clamp sets.

General Specifications
Application Outdoor
Includes Brackets   |   Hardware
Package Quantity 1
 

Mechanical Specifications
Color Silver
Material Type Galvanized steel
Mechanical Tilt 0°–12° in steps of 2°
 

Dimensions
Antenna-to-Pipe Distance 85.0 mm   |   3.3 in
Bracket-to-Bracket Distance 976.0 mm   |   38.4 in
Compatible Diameter, maximum 115.0 mm   |   4.5 in
Compatible Diameter, minimum 60.0 mm   |   2.4 in
Compatible Length, maximum 1500.0 mm   |   59.1 in
Compatible Length, minimum 1200.0 mm   |   47.2 in
Net Weight 5.5 kg   |   12.1 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

page 25 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: May 28, 2019
T-045-GL-E

Adjustable Tilt Pipe Mounting Kit for 2.0"-4.5" (60-115mm) OD round


members for panel antennas. Includes 2 clamp sets.

General Specifications
Application Outdoor
Includes Brackets   |   Hardware
Package Quantity 1
 

Mechanical Specifications
Color Silver
Material Type Galvanized steel
Mechanical Tilt 0°–10°
 

Dimensions
Antenna-to-Pipe Distance 85.0 mm   |   3.3 in
Bracket-to-Bracket Distance 761.0 mm   |   30.0 in
Compatible Diameter, maximum 115.0 mm   |   4.5 in
Compatible Diameter, minimum 60.0 mm   |   2.4 in
Compatible Length, maximum 1200.0 mm   |   47.2 in
Compatible Length, minimum 850.0 mm   |   33.5 in
Net Weight 6.0 kg   |   13.2 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

page 26 of 26
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: May 28, 2019
CVV2NPX308.208R

10-port sector antenna, 2x 790–960 MHz 65° HPBW, 4x 1695-2690


MHz 65° HPBW and 4x 1695-2180 MHz 2x 33° HPBW, 5x RET with
manual override. Bands cascaded SRET
l Integrated Internal Remote Electrical Tilt (RET), with independent control of electrical tilt with manual
override on all arrays

l All Internal RET actuators are connected in “Cascaded SRET


SRET”” configuration

Electrical Specifications
LB LB HB HB HB HB-Dual-Beam2 HB-Dual-Beam2
Frequency Band, MHz 790
790––890 890
890––960 1695
1695––1920 1920
1920––2180 2300
2300––2690 1695
1695––1920 1920
1920––2180
Gain, dBi 15.8 16.1 16.2 16.9 17.3 16.5 18.1
Beam Centers, Horizontal, degrees           ±32 ±30
Beamwidth, Horizontal, degrees 69 68 66 67 65 36 31
Beamwidth, Vertical, degrees 11.1 10.2 10.1 9.0 7.3 10.3 9.1
Beam Tilt, degrees 0– 10 0– 10 0– 10 0– 10 0– 10 0– 10 0– 10
USLS (First Lobe), dB 18 18 18 18 18 18 18
Null Fill, dB -22 -22 -22 -22 -22 -22 -22
Front
Front--to
to--Back Ratio at 180°, dB 32 36 31 30 30 27 31
CPR at Boresight, dB 16 15 17 16 16 10 11
CPR at Sector, dB 10 13 10 10 0    
Isolation, Cross Polarization, dB 28 28 30 30 30 25 25
Isolation, Inter
Inter--band, dB           22 22
Isolation, Beam to Beam, dB           18 18
VSWR | Return Loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150
Input Power per Port, maximum,
300 300 250 250 250 250 250
watts
Polarization   ±45° ±45° ±45° ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 790–890 890–960 1695–1920 1920–2180 2300–2690 1695–1920 1920–2180
Gain by all Beam Tilts, average, dBi 15.7 15.9 15.9 16.5 16.9 15.8 17.5
Gain by all Beam Tilts Tolerance,
±0.2 ±0.1 ±0.3 ±0.5 ±0.7 ±1.1 ±0.9
dB
0 ° | 15.7 0 ° | 16.0 0 ° | 16.0 0 ° | 16.5 0 ° | 17.1 0 ° | 15.9 0 ° | 17.6
Gain by Beam Tilt, average, dBi 5 ° | 15.7 5 ° | 15.9 5 ° | 15.9 5 ° | 16.5 5 ° | 16.9 5 ° | 15.9 5 ° | 17.6
10 ° | 15.6 10 ° | 15.8 10 ° | 15.9 10 ° | 16.3 10 ° | 16.5 10 ° | 15.6 10 ° | 17.3
Beamwidth, Horizontal Tolerance,
±0.7 ±0.5 ±2.8 ±4.3 ±7.6 ±3.4 ±2.1
degrees
Beamwidth, Vertical Tolerance,
±0.5 ±0.4 ±0.7 ±0.6 ±0.6 ±0.6 ±0.7
degrees
USLS, beampeak to 20° above
18 18 18 18 18 18 18
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
26 26 29 29 29 24 28
± 30°, dB
CPR at Boresight, dB 16 16 17 20 20 13 15
CPR at Sector, dB 12 14 12 13 6    

page 1 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
CVV2NPX308.208R

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

Array Layout

 
 

General Specifications
Operating Frequency Band 1695 – 2180 MHz   |   1695 – 2690 MHz   |   790 – 960 MHz
Antenna Type Sector
Band Multiband
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
 

Mechanical Specifications
RF Connector Quantity, total 10
RF Connector Quantity, low band 2
RF Connector Quantity, high band 8
RF Connector Interface 7-16 DIN Female
Color Gray
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Brass   |   Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 348.0 N @ 150 km/h   |   78.2 lbf @ 150 km/h

page 2 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
CVV2NPX308.208R

Wind Loading, lateral 294.0 N @ 150 km/h   |   66.1 lbf @ 150 km/h


Wind Loading, maximum 737.0 N @ 150 km/h   |   165.7 lbf @ 150 km/h
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 2065.0 mm   |   81.3 in
Width 350.0 mm   |   13.8 in
Depth 208.0 mm   |   8.2 in
Net Weight, without mounting kit 35.5 kg   |   78.3 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (4)   |   Low band (1)
Power Consumption, idle state, maximum 2W
Power Consumption, normal conditions, maximum 13 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 1 female   |   1 male
 

Packed Dimensions
Length 2250.0 mm   |   88.6 in
Width 436.0 mm   |   17.2 in
Depth 320.0 mm   |   12.6 in
Shipping Weight 53.0 kg   |   116.8 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

Included Products
T -029
029--GL
GL--E — Adjustable Tilt Pipe Mounting Kit for 2.0"
2.0"--4.5" (60
(60--115mm) OD round members for panel antennas. Includes 2 clamp sets.

page 3 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
CVV2NPX308.208R

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 4 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
HBXX-3817TB1-VTM | HBXX-3817TB1-A2M

4-port multibeam antenna, 4x 1710–2180 MHz, 2x 38° HPBW, RET


compatible
l Enhances network capacity through six sectors site application with only three antenna faces

l Single panel design supporting two separate beams perfectly optimized at horizontal pointing angles of
+27 degrees and –27 degrees from boresight

l Maximizes frequency spectrum utilization to increase Average Revenue Per User (ARPU)

l Reduces antenna count to minimize Cap


Cap--Ex and Op
Op--Ex costs

l High gain with excellent sector edge roll


roll--off and azimuth sidelobe suppression

l Each antenna downtilt can be independently adjusted for greater flexibility in network optimization

Electrical Specifications
Frequency Band, MHz 1710–1880 1850–1990 1920–2180
Gain, dBi 19.3 19.6 19.9
Beam Centers, Horizontal, degrees ±27 ±27 ±27
Beamwidth, Horizontal, degrees 38 36 34
Beamwidth, Vertical, degrees 7.6 7.1 6.7
Beam Tilt, degrees 0– 10 0– 10 0– 10
Horizontal Sidelobe, dB 24 24 22
USLS (First Lobe), dB 23 23 23
Gain Roll
Roll--off at Boresight, dB 10 9 9
Gain Roll
Roll--off at Boresight
±0.7 ±0.8 ±0.9
Tolerance, dB
Front
Front--to
to--Back Ratio at 180°, dB 33 34 35
Isolation, Cross Polarization, port to
30 30 30
port, dB
VSWR | Return Loss, dB 1.43 | 15.0 1.43 | 15.0 1.43 | 15.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150
Input Power per Port, maximum,
250 250 250
watts
Polarization   ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 1710–1880 1850–1990 1920–2180
Gain by all Beam Tilts, average, dBi 18.9 19.4 19.6
Gain by all Beam Tilts Tolerance,
±0.5 ±0.3 ±0.6
dB
0 ° | 18.7 0 ° | 19.1 0 ° | 19.5
Gain by Beam Tilt, average, dBi 5 ° | 19.0 5 ° | 19.5 5 ° | 19.7
10 ° | 18.9 10 ° | 19.4 10 ° | 19.2
Beamwidth, Horizontal Tolerance,
±1.5 ±1.2 ±2.1
degrees
Beamwidth, Vertical Tolerance,
±0.4 ±0.3 ±0.5
degrees
USLS, beampeak to 20° above
17 18 18
beampeak, dB

page 5 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
HBXX-3817TB1-VTM | HBXX-3817TB1-A2M

Front
Front--to
to--Back Total Power at 180°
29 30 28
± 30°, dB
CPR at Boresight, dB 24 24 18
CPR at Sector, dB 12 15 13

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

General Specifications
Operating Frequency Band 1710 – 2180 MHz
Antenna Type Multibeam
Band Single band
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
 

Mechanical Specifications
RF Connector Quantity, total 4
RF Connector Quantity, high band 4
RF Connector Interface 7-16 DIN Female
Color Light gray
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 202.0 N @ 150 km/h   |   45.4 lbf @ 150 km/h
Wind Loading, lateral 166.0 N @ 150 km/h   |   37.3 lbf @ 150 km/h
Wind Loading, maximum 388.0 N @ 150 km/h   |   87.2 lbf @ 150 km/h
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 1390.0 mm   |   54.7 in
Width 301.0 mm   |   11.9 in
Depth 181.0 mm   |   7.1 in
Net Weight, without mounting kit 13.6 kg   |   30.0 lb
 

Remote Electrical Tilt (RET) Information


Model with Factory Installed AISG 2.0 Actuator HBXX-3817TB1-A2M
 

Packed Dimensions

page 6 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
HBXX-3817TB1-VTM | HBXX-3817TB1-A2M

Length 1598.0 mm   |   62.9 in


Width 404.0 mm   |   15.9 in
Depth 310.0 mm   |   12.2 in
Shipping Weight 25.0 kg   |   55.1 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

Included Products
BSAMNT--3 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 7 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
R2HH-6533A-R5

10-port sector/multibeam antenna, 2x 694–960 MHz 65° HPBW and 8x


1710–2180 MHz 4x 33°HPBW, 5x RET with tilt indicators
l Uses the 4.3
4.3--10 connector which is 40 percent smaller than the 7
7--16 DIN connector

l All Internal RET actuators are connected in “Cascaded SRET


SRET”” configuration

l Enhances network capacity through six sectors on high band while maintaining low band coverage layer
through three sectors with only three antenna faces

Electrical Specifications
Frequency Band, MHz 694–790 790–890 880–960 1710–1880 1850–1990 1920–2180
Gain, dBi 14.4 14.8 14.9 15.9 16.5 17.1
Beam Centers, Horizontal, degrees       ±27 ±27 ±27
Beamwidth, Horizontal, degrees 69 67 65 33 32 30
Beamwidth, Vertical, degrees 13.5 12.3 11.5 11.9 11.2 10.6
Beam Tilt, degrees 2– 14 2– 14 2– 14 2– 14 2– 14 2– 14
USLS (First Lobe), dB 14 16 17 17 18 19
Front
Front--to
to--Back Ratio at 180°, dB 32 34 33 31 34 35
Isolation, Cross Polarization, dB 28 28 28 25 25 25
Isolation, Inter
Inter--band, dB 30 30 30 25 25 25
Isolation, Beam to Beam, dB       17 17 17
VSWR | Return Loss, dB 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150
Input Power per Port at 50°C,
300 300 300 200 200 200
maximum, watts
Polarization   ±45° ±45° ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 694–790 790–890 880–960 1710–1880 1850–1990 1920–2180
Gain by all Beam Tilts, average, dBi 14.2 14.6 14.7 15.2 16.0 16.5
Gain by all Beam Tilts Tolerance,
±0.3 ±0.4 ±0.4 ±1 ±0.6 ±0.8
dB
2 ° | 14.3 2 ° | 14.6 2 ° | 14.9 2 ° | 15.2 2 ° | 16.0 2 ° | 16.5
Gain by Beam Tilt, average, dBi 8 ° | 14.2 8 ° | 14.7 8 ° | 14.8 8 ° | 15.3 8 ° | 16.2 8 ° | 16.7
14 ° | 13.9 14 ° | 14.3 14 ° | 14.4 14 ° | 14.8 14 ° | 15.7 14 ° | 16.1
Beamwidth, Horizontal Tolerance,
±1.9 ±2.3 ±2.2 ±1.7 ±1.7 ±1.7
degrees
Beamwidth, Vertical Tolerance,
±1 ±0.8 ±0.7 ±1 ±0.9 ±0.9
degrees
USLS, beampeak to 20° above
14 16 16 17 18 18
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
24 24 22 24 26 27
± 30°, dB
CPR at Boresight, dB 16 16 17 14 15 16
CPR at Sector, dB 11 10 9      
CPR at 10 dB Horizontal
      8 11 11
Beamwidth, dB

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

page 8 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: November 13, 2019
R2HH-6533A-R5

Array Layout

 
 

Port Configuration

 
 

page 9 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: November 13, 2019
R2HH-6533A-R5

General Specifications
Operating Frequency Band 1710 – 2180 MHz   |   694 – 960 MHz
Antenna Type Multibeam
Band Multiband
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
Total Input Power, maximum 1,000 W @ 50 °C
 

Mechanical Specifications
RF Connector Quantity, total 10
RF Connector Quantity, low band 2
RF Connector Quantity, high band 8
RF Connector Interface 4.3-10 Female
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 254.0 N @ 150 km/h   |   57.8 lbf @ 150 km/h
Wind Loading, lateral 214.0 N @ 150 km/h   |   48.1 lbf @ 150 km/h
Wind Loading, maximum 539.0 N @ 150 km/h   |   121.2 lbf @ 150 km/h
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 1580.0 mm   |   62.2 in
Width 350.0 mm   |   13.8 in
Depth 208.0 mm   |   8.2 in
Net Weight, with installed actuator 25.0 kg   |   55.1 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (4)   |   Low band (1)
Power Consumption, idle state, maximum 1W
Power Consumption, normal conditions, maximum 8 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Hardware CommRET v2
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 1 female   |   1 male
 

page 10 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: November 13, 2019
R2HH-6533A-R5

Packed Dimensions
Length 1673.0 mm   |   65.9 in
Width 456.0 mm   |   18.0 in
Depth 357.0 mm   |   14.1 in
Shipping Weight 38.0 kg   |   83.8 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

Included Products
BSAMNT--3 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 11 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: November 13, 2019
R2HH-6533C-R5

10-port sector/multibeam antenna, 2x 694–960 sector and 8x 1695–


2400 multibeam, 65° sector and 33° 4x multibeam, 5x RET with
l All Internal RET actuators are connected in “Cascaded SRET
SRET”” configuration

l Uses the 4.3


4.3--10 connector which is 40 percent smaller than the 7
7--16 DIN connector

Electrical Specifications
Frequency Band, MHz 694–790 790–890 880–960 1695–1880 1850–1990 1920–2180 2300–2400
Gain, dBi 16.0 16.5 16.6 18.0 18.7 19.3 19.7
Beam Centers, Horizontal, degrees       ±27 ±27 ±27 ±27
Beamwidth, Horizontal, degrees 69 67 67 34 32 31 28
Beamwidth, Vertical, degrees 9.7 8.7 8.0 7.8 7.4 7.0 6.2
Beam Tilt, degrees 2– 12 2– 12 2– 12 2– 12 2– 12 2– 12 2– 12
USLS (First Lobe), dB 16 19 15 15 15 16 17
Front
Front--to
to--Back Ratio at 180°, dB 31 34 35 30 34 36 34
Isolation, Cross Polarization, dB 28 28 28 25 25 25 25
Isolation, Inter
Inter--band, dB 30 30 30 30 30 30 30
Isolation, Beam to Beam, dB       17 17 17 17
VSWR | Return Loss, dB 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150
Input Power per Port at 50°C,
300 300 300 200 200 200 200
maximum, watts
Polarization   ±45° ±45° ±45° ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 694–790 790–890 880–960 1695–1880 1850–1990 1920–2180 2300–2400
Gain by all Beam Tilts, average, dBi 15.8 16.3 16.4 17.3 18.3 18.9 19.2
Gain by all Beam Tilts Tolerance,
±0.3 ±0.3 ±0.3 ±0.9 ±0.6 ±0.6 ±1.1
dB
2 ° | 15.7 2 ° | 16.2 2 ° | 16.2 2 ° | 17.2 2 ° | 18.1 2 ° | 18.7 2 ° | 19.3
Gain by Beam Tilt, average, dBi 7 ° | 15.9 7 ° | 16.4 7 ° | 16.5 7 ° | 17.4 7 ° | 18.4 7 ° | 19.0 7 ° | 19.4
12 ° | 15.8 12 ° | 16.3 12 ° | 16.4 12 ° | 17.2 12 ° | 18.2 12 ° | 18.8 12 ° | 18.7
Beamwidth, Horizontal Tolerance,
±2.4 ±1.4 ±1.4 ±1.3 ±1.3 ±1.9 ±1.1
degrees
Beamwidth, Vertical Tolerance,
±0.6 ±0.5 ±0.5 ±0.4 ±0.3 ±0.4 ±0.2
degrees
USLS, beampeak to 20° above
16 18 15 15 15 16 17
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
25 24 25 23 28 29 29
± 30°, dB
CPR at Boresight, dB 14 15 16 17 18 20 16
CPR at Sector, dB 11 10 9        
CPR at 10 dB Horizontal
      5 8 10 7
Beamwidth, dB

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

page 12 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
R2HH-6533C-R5

Array Layout

 
 

Port Configuration

 
 

page 13 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
R2HH-6533C-R5

General Specifications
Operating Frequency Band 1695 – 2400 MHz   |   694 – 960 MHz
Antenna Type Multibeam
Band Multiband
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
Total Input Power, maximum 1,000 W @ 50 °C
 

Mechanical Specifications
RF Connector Quantity, total 10
RF Connector Quantity, low band 2
RF Connector Quantity, high band 8
RF Connector Interface 4.3-10 Female
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 425.0 N @ 150 km/h   |   95.5 lbf @ 150 km/h
Wind Loading, lateral 361.0 N @ 150 km/h   |   81.2 lbf @ 150 km/h
Wind Loading, maximum 899.0 N @ 150 km/h   |   202.1 lbf @ 150 km/h
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 2438.0 mm   |   96.0 in
Width 350.0 mm   |   13.8 in
Depth 208.0 mm   |   8.2 in
Net Weight, with installed actuator 33.5 kg   |   73.9 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (4)   |   Low band (1)
Power Consumption, idle state, maximum 1W
Power Consumption, normal conditions, maximum 8 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Hardware CommRET v2
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 1 female   |   1 male
 

page 14 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
R2HH-6533C-R5

Packed Dimensions
Length 2585.0 mm   |   101.8 in
Width 456.0 mm   |   18.0 in
Depth 357.0 mm   |   14.1 in
Shipping Weight 47.7 kg   |   105.2 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

Included Products
BSAMNT--4 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 15 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
R2HH-6533D-R5

10-port sector/multibeam antenna, 2x 694–960 MHz 65° HPBW and 8x


1695–2180 MHz 4x 33°HPBW, 5x RET with tilt indicators
l All Internal RET actuators are connected in “Cascaded SRET
SRET”” configuration

l Uses the 4.3


4.3--10 connector which is 40 percent smaller than the 7
7--16 DIN connector

l Enhances network capacity through six sectors on high band while maintaining low band coverage layer
through three sectors with only three antenna faces

Electrical Specifications
Frequency Band, MHz 694–790 790–890 880–960 1695–1880 1850–1990 1920–2180
Gain, dBi 16.4 16.9 16.9 18.4 19.3 19.8
Beam Centers, Horizontal, degrees       ±27 ±27 ±27
Beamwidth, Horizontal, degrees 68 65 65 33 31 31
Beamwidth, Vertical, degrees 8.9 8.0 7.4 7.2 6.8 6.4
Beam Tilt, degrees 2– 12 2– 12 2– 12 2– 12 2– 12 2– 12
USLS (First Lobe), dB 17 20 19 16 16 17
Front
Front--to
to--Back Ratio at 180°, dB 32 34 34 28 34 36
Isolation, Cross Polarization, dB 28 28 28 25 25 25
Isolation, Inter
Inter--band, dB 30 30 30 30 30 30
Isolation, Beam to Beam, dB       17 17 17
VSWR | Return Loss, dB 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150
Input Power per Port at 50°C,
300 300 300 250 250 250
maximum, watts
Polarization   ±45° ±45° ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 694–790 790–890 880–960 1695–1880 1850–1990 1920–2180
Gain by all Beam Tilts, average, dBi 16.3 16.7 16.8 17.7 18.8 19.3
Gain by all Beam Tilts Tolerance,
±0.2 ±0.3 ±0.3 ±1.1 ±0.6 ±0.7
dB
2 ° | 16.1 2 ° | 16.5 2 ° | 16.6 2 ° | 17.6 2 ° | 18.6 2 ° | 19.1
Gain by Beam Tilt, average, dBi 7 ° | 16.3 7 ° | 16.8 7 ° | 16.9 7 ° | 17.8 7 ° | 18.9 7 ° | 19.5
12 ° | 16.3 12 ° | 16.6 12 ° | 16.7 12 ° | 17.5 12 ° | 18.6 12 ° | 18.9
Beamwidth, Horizontal Tolerance,
±1.3 ±1.4 ±1.9 ±1.8 ±1.7 ±1.7
degrees
Beamwidth, Vertical Tolerance,
±0.5 ±0.4 ±0.4 ±0.3 ±0.3 ±0.4
degrees
USLS, beampeak to 20° above
17 18 17 15 16 17
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
25 24 24 24 27 28
± 30°, dB
CPR at Boresight, dB 16 17 17 16 17 18
CPR at Sector, dB 10 10 9      
CPR at 10 dB Horizontal
      6 8 10
Beamwidth, dB

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

page 16 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
R2HH-6533D-R5

Array Layout

 
 

Port Configuration

 
 

page 17 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
R2HH-6533D-R5

General Specifications
Operating Frequency Band 1695 – 2180 MHz   |   694 – 960 MHz
Antenna Type Sector
Band Multiband
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
Total Input Power, maximum 1,000 W @ 50 °C
 

Mechanical Specifications
RF Connector Quantity, total 10
RF Connector Quantity, low band 2
RF Connector Quantity, high band 8
RF Connector Interface 4.3-10 Female
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Copper   |   Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 477.0 N @ 150 km/h   |   107.2 lbf @ 150 km/h
Wind Loading, lateral 409.0 N @ 150 km/h   |   91.9 lbf @ 150 km/h
Wind Loading, maximum 1,010.0 N @ 150 km/h   |   227.1 lbf @ 150 km/h
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 2688.0 mm   |   105.8 in
Width 350.0 mm   |   13.8 in
Depth 208.0 mm   |   8.2 in
Net Weight, without mounting kit 35.0 kg   |   77.2 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (4)   |   Low band (1)
Power Consumption, idle state, maximum 1W
Power Consumption, normal conditions, maximum 8 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Hardware CommRET v2
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 1 female   |   1 male
 

page 18 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
R2HH-6533D-R5

Packed Dimensions
Length 2830.0 mm   |   111.4 in
Width 460.0 mm   |   18.1 in
Depth 350.0 mm   |   13.8 in
Shipping Weight 50.0 kg   |   110.2 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

Included Products
BSAMNT--4 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 19 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
RR2HH-6533D-R6

12-port sector/multibeam antenna, 4x 694–960 MHz 65° HPBW and 8x


1695–2400 MHz 4x 33°HPBW, 6x RET with tilt indicators
l All Internal RET actuators are connected in “Cascaded SRET
SRET”” configuration

l Uses the 4.3


4.3--10 connector which is 40 percent smaller than the 7
7--16 DIN connector

l Enhances network capacity through six sectors on high band while maintaining low band coverage layer
through three sectors with only three antenna faces

Electrical Specifications
Frequency Band, MHz 694–790 790–890 880–960 1695–1880 1850–1990 1920–2180 2300–2400
Gain, dBi 15.7 15.9 16.0 17.9 18.7 19.3 19.2
Beam Centers, Horizontal, degrees       ±27 ±27 ±27 ±27
Beamwidth, Horizontal, degrees 68 64 61 32 31 30 30
Beamwidth, Vertical, degrees 8.9 8.0 7.4 7.3 6.9 6.5 5.7
Beam Tilt, degrees 2– 12 2– 12 2– 12 2– 12 2– 12 2– 12 2– 12
USLS (First Lobe), dB 17 19 19 17 17 18 22
Front
Front--to
to--Back Ratio at 180°, dB 32 31 31 35 35 36 34
Isolation, Cross Polarization, dB 28 28 28 25 25 25 25
Isolation, Inter
Inter--band, dB 30 30 30 30 30 30 30
Isolation, Beam to Beam, dB       17 17 17 17
VSWR | Return Loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150
Input Power per Port at 50°C,
200 200 200 150 150 150 150
maximum, watts
Polarization   ±45° ±45° ±45° ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 694–790 790–890 880–960 1695–1880 1850–1990 1920–2180 2300–2400
Gain by all Beam Tilts, average, dBi 15.3 15.7 16.1 17.2 18.2 18.7 18.5
Gain by all Beam Tilts Tolerance,
±0.4 ±0.3 ±0.4 ±1.3 ±0.6 ±0.8 ±1.6
dB
2 ° | 15.3 2 ° | 15.6 2 ° | 15.8 2 ° | 17.0 2 ° | 18.0 2 ° | 18.5 2 ° | 18.5
Gain by Beam Tilt, average, dBi 7 ° | 15.4 7 ° | 15.8 7 ° | 16.1 7 ° | 17.3 7 ° | 18.3 7 ° | 18.9 7 ° | 18.8
12 ° | 15.2 12 ° | 15.5 12 ° | 15.9 12 ° | 16.9 12 ° | 17.9 12 ° | 18.4 12 ° | 18.1
Beamwidth, Horizontal Tolerance,
±6.4 ±4.9 ±3.4 ±2.4 ±1.2 ±1.6 ±1.4
degrees
Beamwidth, Vertical Tolerance,
±0.5 ±0.6 ±0.5 ±0.4 ±0.3 ±0.5 ±0.3
degrees
USLS, beampeak to 20° above
17 16 17 15 16 16 13
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
21 21 22 29 30 30 29
± 30°, dB
CPR at Boresight, dB 19 19 18 16 16 18 13
CPR at Sector, dB 12 8 11        
CPR at 10 dB Horizontal
      4 7 8 9
Beamwidth, dB

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

page 20 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
RR2HH-6533D-R6

Array Layout

 
 

Port Configuration

 
 

page 21 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
RR2HH-6533D-R6

General Specifications
Operating Frequency Band 1695 – 2400 MHz   |   694 – 960 MHz
Antenna Type Sector
Band Multiband
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
Total Input Power, maximum 700 W @ 50 °C
 

Mechanical Specifications
RF Connector Quantity, total 12
RF Connector Quantity, low band 4
RF Connector Quantity, high band 8
RF Connector Interface 4.3-10 Female
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Copper   |   Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 1,070.0 N @ 150 km/h
Wind Loading, lateral 375.0 N @ 150 km/h
Wind Loading, maximum 1,385.0 N @ 150 km/h   |   311.4 lbf @ 150 km/h
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 2688.0 mm   |   105.8 in
Width 498.0 mm   |   19.6 in
Depth 197.0 mm   |   7.8 in
Net Weight, without mounting kit 54.0 kg   |   119.0 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (4)   |   Low band (2)
Power Consumption, idle state, maximum 1W
Power Consumption, normal conditions, maximum 8 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Hardware CommRET v2
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 2 female   |   2 male
 

page 22 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
RR2HH-6533D-R6

Packed Dimensions
Length 2880.0 mm   |   113.4 in
Width 608.0 mm   |   23.9 in
Depth 352.0 mm   |   13.9 in
Shipping Weight 78.0 kg   |   172.0 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

Included Products
BSAMNT--4 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

BSAMNT--M4 — Middle Downtilt Mounting Kit for Long Antennas for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one
BSAMNT
scissor bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 23 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 20, 2019
RVV2H-6533B-R5

10-port sector antenna, 2x 694–960 and 4x 1695-2690 MHz 65° HPBW


and 4x 1710-2400 MHz 2x 33° HPBW, 5x RET.
l All Internal RET actuators are connected in “Cascaded SRET
SRET”” configuration

Electrical Specifications
R1 R1 Y1-Y2 Y1-Y2 Y1-Y2 Y3-Y4 Y3-Y4 Y3-Y4
Frequency Band, MHz 694
694––790 790790––960 1695
1695––1920 1920
1920––2180 2300
2300––2690 1710
1710––1880 1920
1920––2180 2300
2300––2400
Gain, dBi 15.0 15.3 16.6 17.0 17.3 16.4 17.8 18.0
Beam Centers, Horizontal, degrees           ±27 ±27 ±27
Beamwidth, Horizontal, degrees 68 66 62 63 66 33 31 27
Beamwidth, Vertical, degrees 11.9 10.5 8.9 8.0 6.6 10.2 9.2 8.3
Beam Tilt, degrees 2– 14 2– 14 2– 12 2– 12 2– 12 2– 12 2– 12 2– 12
USLS (First Lobe), dB 21 20 18 18 20 20 21 24
Front
Front--to
to--Back Ratio at 180°, dB 31 32 36 36 30 28 35 35
Isolation, Cross Polarization, dB 28 28 26 26 26 25 25 25
Isolation, Inter
Inter--band, dB 28 28 28 28 28 28 28 28
VSWR | Return Loss, dB 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150 -150
Input Power per Port at 50°C,
300 300 250 250 250 250 250 250
maximum, watts
Polarization   ±45° ±45° ±45° ±45° ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 694–790 790–960 1695–1920 1920–2180 2300–2690 1710–1880 1920–2180 2300–2400
Gain by all Beam Tilts, average,
14.8 15.1 16.1 16.7 16.8 15.9 17.4 17.5
dBi
Gain by all Beam Tilts
±0.3 ±0.4 ±0.6 ±0.4 ±0.5 ±0.9 ±0.6 ±1.5
Tolerance, dB
2 ° | 14.8 2 ° | 15.2 2 ° | 16.1 2 ° | 16.5 2 ° | 16.6 2 ° | 15.9 2 ° | 17.2 2 ° | 17.5
Gain by Beam Tilt, average, dBi 8 ° | 14.8 8 ° | 15.1 7 ° | 16.2 7 ° | 16.7 7 ° | 17.0 7 ° | 16.0 7 ° | 17.5 7 ° | 17.7
14 ° | 14.6 14 ° | 14.8 12 ° | 16.1 12 ° | 16.7 12 ° | 16.7 12 ° | 15.7 12 ° | 17.2 12 ° | 16.9
Beamwidth, Horizontal
±1.5 ±1.9 ±3.3 ±3.7 ±5 ±1.5 ±1.6 ±0.9
Tolerance, degrees
Beamwidth, Vertical Tolerance,
±0.8 ±0.8 ±0.7 ±0.6 ±0.5 ±0.5 ±0.5 ±0.3
degrees
USLS, beampeak to 20° above
21 15 16 18 14 20 19 19
beampeak, dB
Front
Front--to
to--Back Total Power at
25 24 29 26 25 22 28 27
180° ± 30°, dB
CPR at Boresight, dB 17 17 18 21 16 18 20 15
CPR at Sector, dB 10 9 13 12 7      
CPR at 10 dB Horizontal
          7 11 7
Beamwidth, dB

* CommScope
CommScope®® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the

page 24 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
RVV2H-6533B-R5
whitepaper Time to Raise the Bar on BSAs.

Array Layout

 
 

Port Configuration

 
 
page 25 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
RVV2H-6533B-R5
 

General Specifications
Operating Frequency Band 1695 – 2690 MHz   |   1710 – 2400 MHz   |   694 – 960 MHz
Antenna Type Multibeam
Band Multiband
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
Total Input Power, maximum 1,000 W @ 50 °C
 

Mechanical Specifications
RF Connector Quantity, total 10
RF Connector Quantity, low band 2
RF Connector Quantity, high band 8
RF Connector Interface 4.3-10 Female
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 334.0 N @ 150 km/h   |   78.2 lbf @ 150 km/h
Wind Loading, lateral 282.0 N @ 150 km/h   |   63.4 lbf @ 150 km/h
Wind Loading, maximum 708.0 N @ 150 km/h   |   159.2 lbf @ 150 km/h
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 1996.0 mm   |   78.6 in
Width 350.0 mm   |   13.8 in
Depth 208.0 mm   |   8.2 in
Net Weight, without mounting kit 28.2 kg   |   62.2 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (4)   |   Low band (1)
Power Consumption, idle state, maximum 1W
Power Consumption, normal conditions, maximum 8 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Hardware CommRET v2
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 2 female   |   2 male
 
page 26 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
RVV2H-6533B-R5
 

Packed Dimensions
Length 2136.0 mm   |   84.1 in
Width 456.0 mm   |   18.0 in
Depth 357.0 mm   |   14.1 in
Shipping Weight 42.2 kg   |   93.0 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

Included Products
BSAMNT--3 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 27 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
T-029-GL-E

Adjustable Tilt Pipe Mounting Kit for 2.0"-4.5" (60-115mm) OD round


members for panel antennas. Includes 2 clamp sets.

General Specifications
Application Outdoor
Includes Brackets   |   Hardware
Package Quantity 1
 

Mechanical Specifications
Color Silver
Material Type Galvanized steel
Mechanical Tilt 0°–8°
 

Dimensions
Antenna-to-Pipe Distance 85.0 mm   |   3.3 in
Bracket-to-Bracket Distance 1400.0 mm   |   55.1 in
Compatible Diameter, maximum 115.0 mm   |   4.5 in
Compatible Diameter, minimum 60.0 mm   |   2.4 in
Compatible Length, maximum 2850.0 mm   |   112.2 in
Compatible Length, minimum 1500.0 mm   |   59.1 in
Net Weight 6.0 kg   |   13.2 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

page 28 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: May 28, 2019
BSAMNT-3

Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD
round members. Kit contains one scissor top bracket set and one bottom
bracket set.

General Specifications
Application Outdoor
Includes Brackets   |   Hardware
Package Quantity 1
 

Mechanical Specifications
Color Silver
Material Type Galvanized steel
 

Dimensions
Compatible Diameter, maximum 114.3 mm   |   4.5 in
Compatible Diameter, minimum 61.0 mm   |   2.4 in
Net Weight 6.2 kg   |   13.7 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

page 29 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: November 17, 2019
BSAMNT-4

Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD
round members. Kit contains one scissor top bracket set and one bottom
bracket set.

General Specifications
Application Outdoor
Includes Brackets   |   Hardware
Package Quantity 1
 

Mechanical Specifications
Color Silver
Material Type Galvanized steel
 

Dimensions
Compatible Diameter, maximum 114.3 mm   |   4.5 in
Compatible Diameter, minimum 61.0 mm   |   2.4 in
Net Weight 6.6 kg   |   14.6 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

page 30 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: November 17, 2019
BSAMNT-M4

Middle Downtilt Mounting Kit for Long Antennas for 2.4 - 4.5 in (60 - 115
mm) OD round members. Kit contains one scissor bracket set.

General Specifications
Application Outdoor
Includes Brackets   |   Hardware
Package Quantity 1
 

Mechanical Specifications
Color Silver
Material Type Galvanized steel
 

Dimensions
Compatible Diameter, maximum 114.3 mm   |   4.5 in
Compatible Diameter, minimum 61.0 mm   |   2.4 in
Net Weight 4.8 kg   |   10.6 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

page 31 of 31
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: November 17, 2019
RVV2H-6533D-R5

10-port sector antenna, 2x 694–960 and 4x 1695-2690 MHz 65° HPBW


and 4x 1695-2180 MHz 2x 33° HPBW, 5x RET.
l All Internal RET actuators are connected in “Cascaded SRET
SRET”” configuration

Electrical Specifications
R1 R1 HB-Dual-Beam2 HB-Dual-Beam2 Y1-Y2 Y1-Y2 Y1-Y2
Frequency Band, MHz 694
694––790 790790––960 1695
1695––1920 1920
1920––2180 1695
1695––1920 1920
1920––2180 2300
2300––2690
Gain, dBi 16.6 16.9 18.1 19.2 16.8 17.3 17.9
Beam Centers, Horizontal, degrees     ±27 ±27      
Beamwidth, Horizontal, degrees 69 65 32 30 63 62 63
Beamwidth, Vertical, degrees 8.5 7.4 7.2 6.6 7.4 6.6 5.5
Beam Tilt, degrees 0– 10 0– 10 2– 12 2– 12 2– 12 2– 12 2– 12
USLS (First Lobe), dB 16 17 16 15 18 18 16
Front
Front--to
to--Back Ratio at 180°, dB 35 35 31 36 38 35 35
Isolation, Cross Polarization, dB 28 28 25 25 28 28 28
Isolation, Inter
Inter--band, dB 28 28 28 28 28 28 28
Isolation, Beam to Beam, dB     17 17      
VSWR | Return Loss, dB 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150
Input Power per Port at 50°C,
300 300 250 250 250 250 250
maximum, watts
Polarization   ±45° ±45° ±45° ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 694–790 790–960 1695–1920 1920–2180 1695–1920 1920–2180 2300–2690
Gain by all Beam Tilts, average, dBi 16.3 16.6 17.5 18.8 16.3 16.8 17.4
Gain by all Beam Tilts Tolerance,
±0.4 ±0.4 ±1 ±0.6 ±0.7 ±0.7 ±0.8
dB
0 ° | 16.2 0 ° | 16.5 2 ° | 17.5 2 ° | 18.7 2 ° | 16.2 2 ° | 16.5 2 ° | 17.1
Gain by Beam Tilt, average, dBi 5 ° | 16.4 5 ° | 16.7 7 ° | 17.7 7 ° | 18.9 7 ° | 16.5 7 ° | 17.0 7 ° | 17.7
10 ° | 15.8 10 ° | 16.6 12 ° | 17.2 12 ° | 18.3 12 ° | 16.1 12 ° | 16.7 12 ° | 17.1
Beamwidth, Horizontal Tolerance,
±1.6 ±2.3 ±2.4 ±1.6 ±3.6 ±2.8 ±4.9
degrees
Beamwidth, Vertical Tolerance,
±0.5 ±0.6 ±0.4 ±0.3 ±0.6 ±0.5 ±0.5
degrees
USLS, beampeak to 20° above
16 17 15 15 13 15 14
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
27 25 24 29 28 27 26
± 30°, dB
CPR at Boresight, dB 16 17 18 20 23 21 19
CPR at Sector, dB 10 10 7 8 10 12 7

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

page 1 of 15
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
RVV2H-6533D-R5

Array Layout

 
 

Port Configuration

 
 

page 2 of 15
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
RVV2H-6533D-R5

General Specifications
Operating Frequency Band 1695 – 2180 MHz   |   1695 – 2690 MHz   |   694 – 960 MHz
Antenna Type Multibeam
Band Multiband
Performance Note Outdoor usage
Total Input Power, maximum 1,000 W @ 50 °C
 

Mechanical Specifications
RF Connector Quantity, total 10
RF Connector Quantity, low band 2
RF Connector Quantity, high band 8
RF Connector Interface 4.3-10 Female
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 107.2 lbf @ 150 km/h   |   477.0 N @ 150 km/h
Wind Loading, lateral 409.0 N @ 150 km/h   |   91.9 lbf @ 150 km/h
Wind Loading, maximum 1,010.0 N @ 150 km/h   |   227.1 lbf @ 150 km/h
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 2688.0 mm   |   105.8 in
Width 350.0 mm   |   13.8 in
Depth 208.0 mm   |   8.2 in
Net Weight, without mounting kit 35.0 kg   |   77.2 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (4)   |   Low band (1)
Power Consumption, idle state, maximum 1W
Power Consumption, normal conditions, maximum 8 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Hardware CommRET v2
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 2 female   |   2 male
 

page 3 of 15
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
RVV2H-6533D-R5

Packed Dimensions
Length 2830.0 mm   |   111.4 in
Width 460.0 mm   |   18.1 in
Depth 350.0 mm   |   13.8 in
Shipping Weight 48.6 kg   |   107.1 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

Included Products
BSAMNT--4 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 4 of 15
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: September 23, 2019
RVV2HH-6533D-R7

14-port sector antenna, 2x 694–960 and 4x 1695-2690 MHz 65° HPBW


and 8x 1695-2400 MHz 4x 33° HPBW, 7x RET.
l All Internal RET actuators are connected in “Cascaded SRET
SRET”” configuration

l Supports re
re--configurable antenna sharing capability enabling control of the internal RET system using
up to two separate RET compatible OEM radios

Electrical Specifications
R1 R1 R1 Y1-Y4 Y1-Y4 Y5&Y6 Y5&Y6 Y5&Y6
Frequency Band, MHz 694
694––790 790790––890 880
880––960 1695
1695––1920 1920
1920––2400 1695
1695––1880 1920
1920––2180 2300
2300––2690
Gain, dBi 16.5 16.4 16.9 17.6 18.9 17.3 18.3 18.6
Beam Centers, Horizontal, degrees       ±27 ±27      
Beamwidth, Horizontal, degrees 62 63 59 34 29 67 64 59
Beamwidth, Vertical, degrees 8.5 7.7 7.1 7.6 6.4 6.3 5.6 4.9
Beam Tilt, degrees 2– 12 2– 12 2– 12 2– 12 2– 12 2– 12 2– 12 2– 12
USLS (First Lobe), dB 16 18 19 18 17 17 18 19
Front
Front--to
to--Back Ratio at 180°, dB 34 31 31 36 35 36 36 29
Isolation, Cross Polarization, dB 28 28 28 25 25 28 28 28
Isolation, Inter
Inter--band, dB 30 30 30 30 30 30 30 30
VSWR | Return Loss, dB 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150 -150
Input Power per Port, maximum,
300 300 300 250 250 250 250 250
watts
Polarization   ±45° ±45° ±45° ±45° ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 694–790 790–890 880–960 1695–1920 1920–2400 1695–1880 1920–2180 2300–2690
Gain by all Beam Tilts, average,
16.3 16.2 16.5 17.1 18.3 16.8 17.4 17.7
dBi
Gain by all Beam Tilts
±0.3 ±0.3 ±0.5 ±1 ±1.1 ±0.7 ±0.6 ±0.5
Tolerance, dB
2 ° | 16.1 2 ° | 15.8 2 ° | 15.9 2 ° | 17.1 2 ° | 18.4 2 ° | 16.6 2 ° | 17.3 2 ° | 17.6
Gain by Beam Tilt, average, dBi 7 ° | 16.2 7 ° | 16.1 7 ° | 16.3 7 ° | 17.2 7 ° | 18.5 7 ° | 16.7 7 ° | 17.6 7 ° | 17.9
12 ° | 16.1 12 ° | 16.0 12 ° | 16.2 12 ° | 16.9 12 ° | 17.8 12 ° | 16.6 12 ° | 17.3 12 ° | 17.6
Beamwidth, Horizontal
±2.8 ±2.5 ±4.7 ±3.9 ±3.3 ±3.2 ±4.8 ±4.2
Tolerance, degrees
Beamwidth, Vertical Tolerance,
±0.6 ±0.4 ±0.4 ±0.5 ±0.6 ±0.4 ±0.3 ±0.4
degrees
USLS, beampeak to 20° above
15 16 16 15 13 14 16 15
beampeak, dB
Front
Front--to
to--Back Total Power at
29 28 28 28 27 27 28 25
180° ± 30°, dB
CPR at Boresight, dB 18 19 18 16 19 18 23 22
CPR at Sector, dB 11 9 8     12 10 6
CPR at 10 dB Horizontal
      8 10      
Beamwidth, dB

* CommScope
CommScope®® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the

page 5 of 15
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: January 30, 2020
RVV2HH-6533D-R7
whitepaper Time to Raise the Bar on BSAs.

Array Layout

 
 

Port Configuration

 
 
page 6 of 15
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: January 30, 2020
RVV2HH-6533D-R7
 

General Specifications
Operating Frequency Band 1695 – 2400 MHz   |   1695 – 2690 MHz   |   694 – 960 MHz
Antenna Type Multibeam
Band Multiband
Performance Note Outdoor usage
Total Input Power, maximum 1,000 W @ 50 °C
 

Mechanical Specifications
RF Connector Quantity, total 14
RF Connector Quantity, low band 2
RF Connector Quantity, high band 12
RF Connector Interface 4.3-10 Female
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 1,070.0 N @ 150 km/h   |   240.5 lbf @ 150 km/h
Wind Loading, lateral 375.0 N @ 150 km/h   |   84.3 lbf @ 150 km/h
Wind Loading, maximum 1,385.0 N @ 150 km/h   |   311.4 lbf @ 150 km/h
Effective Projected Area (EPA), frontal 1.00 m²   |   10.76 ft²
Effective Projected Area (EPA), lateral 0.35 m²   |   3.77 ft²
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 2688.0 mm   |   105.8 in
Width 498.0 mm   |   19.6 in
Depth 197.0 mm   |   7.8 in
Net Weight, without mounting kit 55.6 kg   |   122.6 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (6)   |   Low band (1)
Power Consumption, idle state, maximum 1W
Power Consumption, normal conditions, maximum 8 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Hardware CommRET v2
RET Interface 8-pin DIN Female   |   8-pin DIN Male

page 7 of 15
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: January 30, 2020
RVV2HH-6533D-R7

RET Interface, quantity 2 female   |   2 male


 

Packed Dimensions
Length 2880.0 mm   |   113.4 in
Width 608.0 mm   |   23.9 in
Depth 352.0 mm   |   13.9 in
Shipping Weight 72.3 kg   |   159.4 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

Included Products
BSAMNT--4 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

BSAMNT--M4 — Middle Downtilt Mounting Kit for Long Antennas for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one
BSAMNT
scissor bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 8 of 15
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: January 30, 2020
RVV2NPX310.211R

10-port sector antenna, 2x 694–960 MHz 65° HPBW, 4x 1695-2690


MHz 65° HPBW and 2x 1695-2180 MHz 2x 33° HPBW, 5x RET with
manual override. Bands cascaded SRET
l Integrated Internal Remote Electrical Tilt (RET), with independent control of electrical tilt with manual
override on all arrays

l All Internal RET actuators are connected in “Cascaded SRET


SRET”” configuration

Electrical Specifications
LB LB LB HB HB HB HB-Dual-Beam2 HB-Dual-Beam2
Frequency Band, MHz 694
694––790 790
790––890 890
890––960 1695
1695––1920 1920
1920––2180 2300
2300––2690 1695
1695––1920 1920
1920––2180
Gain, dBi 16.2 16.5 16.7 17.5 18.2 18.8 17.2 18.8
Beam Centers, Horizontal, degrees             ±31 ±28
Beamwidth, Horizontal, degrees 69 68 68 62 62 61 36 32
Beamwidth, Vertical, degrees 10.1 8.9 8.3 7.5 6.7 5.5 7.7 6.9
Beam Tilt, degrees 0– 10 0– 10 0– 10 0– 10 0– 10 0– 10 0– 10 0– 10
USLS (First Lobe), dB 18 18 18 18 18 18 18 18
Null Fill, dB -22 -22 -22 -22 -22 -22 -22 -22
Front
Front--to
to--Back Ratio at 180°, dB 31 33 34 35 38 38 28 33
Front
Front--to
to--Back Total Power at 180°
27 27 27 27 27 29 24 27
± 30°, dB
Isolation, Cross Polarization, dB 28 28 28 30 30 30 25 25
Isolation, Beam to Beam, dB             18 18
VSWR | Return Loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.43 | 15.0 1.43 | 15.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150 -150
Input Power per Port, maximum,
300 300 300 250 250 250 250 250
watts
Polarization   ±45° ±45° ±45° ±45° ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*


Frequency Band, MHz 694–790 790–890 890–960 1695–1920 1920–2180 2300–2690 1695–1920 1920–2180
Gain by all Beam Tilts, average,
15.9 16.4 16.6 17.1 17.9 18.3 16.4 18.4
dBi
Gain by all Beam Tilts
±0.5 ±0.2 ±0.2 ±0.6 ±0.4 ±0.6 ±1.2 ±0.6
Tolerance, dB
0 ° | 15.9 0 ° | 16.4 0 ° | 16.6 0 ° | 17.1 0 ° | 18.0 0 ° | 18.3 0 ° | 16.4 0 ° | 18.4
Gain by Beam Tilt, average, dBi 5 ° | 15.9 5 ° | 16.4 5 ° | 16.7 5 ° | 17.1 5 ° | 18.0 5 ° | 18.3 5 ° | 16.3 5 ° | 18.4
10 ° | 15.9 10 ° | 16.5 10 ° | 16.5 10 ° | 17.2 10 ° | 17.8 10 ° | 18.2 10 ° | 16.4 10 ° | 18.3
Beamwidth, Horizontal
±0.8 ±0.6 ±1 ±2.9 ±2.8 ±5.8 ±2 ±2.3
Tolerance, degrees
Beamwidth, Vertical Tolerance,
±0.6 ±0.4 ±0.3 ±0.5 ±0.5 ±0.4 ±0.4 ±0.4
degrees
USLS, beampeak to 20° above
18 18 18 18 18 18 18 18
beampeak, dB
CPR at Boresight, dB 15 16 16 20 20 20 12 10
CPR at Sector, dB 11 11 13 11 11 8 7 5

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

page 9 of 15
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
RVV2NPX310.211R

Array Layout

 
 

General Specifications
page 10 of 15
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
RVV2NPX310.211R

Operating Frequency Band 1695 – 2180 MHz   |   1695 – 2690 MHz   |   694 – 960 MHz
Antenna Type Sector
Band Multiband
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
 

Mechanical Specifications
RF Connector Quantity, total 10
RF Connector Quantity, low band 2
RF Connector Quantity, high band 8
RF Connector Interface 7-16 DIN Female
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 493.0 N @ 150 km/h   |   111.1 lbf @ 150 km/h
Wind Loading, lateral 423.0 N @ 150 km/h   |   95.1 lbf @ 150 km/h
Wind Loading, maximum 1,044.0 N @ 150 km/h   |   234.7 lbf @ 150 km/h
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 2763.5 mm   |   108.8 in
Width 350.0 mm   |   13.8 in
Depth 208.0 mm   |   8.2 in
Net Weight, without mounting kit 46.1 kg   |   101.6 lb
 

Remote Electrical Tilt (RET) Information


Input Voltage 10–30 Vdc
Internal RET High band (4)   |   Low band (1)
Power Consumption, idle state, maximum 2W
Power Consumption, normal conditions, maximum 13 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 1 female   |   1 male
 

Packed Dimensions
Length 2985.0 mm   |   117.5 in

page 11 of 15
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
RVV2NPX310.211R

Width 436.0 mm   |   17.2 in


Depth 320.0 mm   |   12.6 in
Shipping Weight 68.5 kg   |   151.0 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

Included Products
T -029
029--GL
GL--E — Adjustable Tilt Pipe Mounting Kit for 2.0"
2.0"--4.5" (60
(60--115mm) OD round members for panel antennas. Includes 2 clamp sets.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 12 of 15
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: December 19, 2019
BSAMNT-4

Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD
round members. Kit contains one scissor top bracket set and one bottom
bracket set.

General Specifications
Application Outdoor
Includes Brackets   |   Hardware
Package Quantity 1
 

Mechanical Specifications
Color Silver
Material Type Galvanized steel
 

Dimensions
Compatible Diameter, maximum 114.3 mm   |   4.5 in
Compatible Diameter, minimum 61.0 mm   |   2.4 in
Net Weight 6.6 kg   |   14.6 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

page 13 of 15
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: November 17, 2019
BSAMNT-M4

Middle Downtilt Mounting Kit for Long Antennas for 2.4 - 4.5 in (60 - 115
mm) OD round members. Kit contains one scissor bracket set.

General Specifications
Application Outdoor
Includes Brackets   |   Hardware
Package Quantity 1
 

Mechanical Specifications
Color Silver
Material Type Galvanized steel
 

Dimensions
Compatible Diameter, maximum 114.3 mm   |   4.5 in
Compatible Diameter, minimum 61.0 mm   |   2.4 in
Net Weight 4.8 kg   |   10.6 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)

page 14 of 15
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: November 17, 2019
T-029-GL-E

Adjustable Tilt Pipe Mounting Kit for 2.0"-4.5" (60-115mm) OD round


members for panel antennas. Includes 2 clamp sets.

General Specifications
Application Outdoor
Includes Brackets   |   Hardware
Package Quantity 1
 

Mechanical Specifications
Color Silver
Material Type Galvanized steel
Mechanical Tilt 0°–8°
 

Dimensions
Antenna-to-Pipe Distance 85.0 mm   |   3.3 in
Bracket-to-Bracket Distance 1400.0 mm   |   55.1 in
Compatible Diameter, maximum 115.0 mm   |   4.5 in
Compatible Diameter, minimum 60.0 mm   |   2.4 in
Compatible Length, maximum 2850.0 mm   |   112.2 in
Compatible Length, minimum 1500.0 mm   |   59.1 in
Net Weight 6.0 kg   |   13.2 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

page 15 of 15
February 2, 2020

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: May 28, 2019

Potrebbero piacerti anche