Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Refer to the exhibit. All routers are configured for OSPF area 0. The network
administrator requires that R2 always be the DR and maintain adjacency.
Configure R1 and R3 with an IP address whose value is higher than that of R2.
2
Refer to the exhibit. The network has three connected routers: R1, R2 and R3. The
routes of all three routers are displayed. What can be verified from the output?
Refer to the exhibit. R1 knows two routes, Path A and Path B, to the Ethernet
network attached to R3. R1 learned Path A to network 10.2.0.0/16 from a static route
and Path B to network 10.2.0.0/16 from EIGRP. Which route will R1 install in its
routing table?
Both routes are installed and load balancing occurs across both paths.
The route via Path B is installed because the EIGRP route has the best metric to
network 10.2.0.0/16.
The route via Path A is installed because the static route has the best metric to
network 10.2.0.0/16.
The route via Path B is installed because the EIGRP route has the lowest
administrative distance to network 10.2.0.0/16.
The route via Path A is installed because the static route has the lowest
administrative distance to network 10.2.0.0/16.
Flash
NVRAM
ROM
SDRAM
5
Refer to the exhibit. Which network command will prevent EIGRP on router RA from
advertising the Ethernet networks but will allow the advertisement of all networks on
the WAN links?
Refer to the exhibit. A network administrator has configured R1 as shown, and all
interfaces are functioning correctly. A ping from R1 to 172.16.1.1 fails. What could be
the cause of this problem?
Refer to the exhibit. All routers are configured with RIPv2 active on all interfaces.
Automatic summarization is in effect. Why does the routing table on R3 include the
209.165.200.228/30 network but not the 172.30.1.0/24 and 172.30.2.0/24 networks?
Refer to the routing table shown in the exhibit. What is the meaning of the highlighted
value 192?
It is the value assigned by the Dijkstra algorithm that designates the number of hops
in the network.
It is the value used by the DUAL algorithm to determine the bandwidth for the link.
9 Which multicast address does EIGRP use to send hello and updates packets?
224.0.0.5
224.0.0.6
224.0.0.9
224.0.0.10
10
A network administrator has enabled RIP on routers B and C in the network diagram.
Which of the following commands will prevent RIP updates from being sent to Router
A?
11Which routing protocol maintains a topology table separate from the routing table?
IGRP
RIPv1
RIPv2
EIGRP
12A network technician must reduce the amount of broadcast traffic on the network
while maintaining full connectivity between all different network segments. Which
device should the administrator deploy?
hub
router
Layer 2 switch
multiport repeater
Refer to the exhibit. What summary address can Router2 advertise to Router1 to
reach the three networks on Routers 3, 4, and 5 without advertising any public
address space or overlapping the networks on Router1?
172.16.0.0/8
172.16.0.0/10
172.16.0.0/13
172.16.0.0/20
172.16.0.0/24
255.255.224.0
255.255.240.0
255.255.248.0
255.255.252.0
17
Refer to the exhibit. The show cdp neighbors command was run at R1. Which two
facts about the newly detected device can be determined from the output? (Choose
two.)
Refer to the exhibit. All routes are advertised and fully operational on all routers.
Which statement is true about the path that the data will take from router A to router
B?
If EIGRP is used with default configurations, the data will be equally distributed
between two paths — A, D, B and A, C, B.
If RIPv1 is used with default configurations, the data will be load-balanced on all
paths.
If EIGRP and OSPF are both used with default configurations, the data will be sent
through paths learned by the OSPF protocol.
If RIPv2 is used with default configurations, the data will be equally distributed
between two paths — A, D, B and A, C, D.
19
There can be only one FastEthernet interface enabled on a router at one time.
The administrator did not exit to global configuration mode before configuring
FastEthernet0/1.
20
Refer to the exhibit. All router interfaces are configured with an IP address and are
operational. If no routing protocols or static routes are configured, what information
will be included in the show ip route command output for router A?
The routing table will be empty because routes and dynamic routes have not been
configured.
Refer to the exhibit. The network is running the RIP routing protocol. Network
10.0.0.0 goes down. Which statement is true regarding how the routers in this
topology will respond to this event?
Router5 flushes the unreachable route from its routing table in 30 seconds.
Router4 will learn about the failed route 30 seconds later in the next periodic update.
Router5 will send Router4 a triggered update with a metric of 16 for network 10.0.0.0.
Split horizon will prevent Router4 from fowarding packets to the 10.0.0.0 network
until the holddown timer expires.
22
Refer to the exhibit. The network administrator issues the command no ip classless
on Router1. What forwarding action will take place on a packet that is received by
Router1 and is destined for host 192.168.0.26?
The packet will match the 192.168.0.0 network and be forwarded out Serial 0/0.
The packet will most closely match the 192.168.0.8 subnet and be forwarded out
Serial 0/1.
25
Refer to the exhibit. Routers R1 and R2 are directly connected via their serial
interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the
directly connected serial interface of their neighbor, but they cannot form an EIGRP
neighbor adjacency.
26A network administrator needs to configure a single router to load-balance the traffic
over unequal cost paths. Which routing protocol should the administrator use?
EIGRP
OSPF
RIPv1
RIPv2
27
Refer to the exhibit. Based on the partial output in the exhibit, why can users
establish a console connection to this router without entering a password?
The network shown in the diagram is having problems routing traffic. It is suspected
that the problem is with the addressing scheme. What is the problem with the
addressing used in the topology?
The subnetwork configured on the serial link between Router1 and Router2 overlaps
with the subnetwork assigned to Ethernet0 of Router3.
New routing updates are ignored until the network has converged.
The unreachable route is cleared from the routing table after the invalid timer expires.
30What command would the network administrator apply to a router that is running
OSPF to advertise the entire range of addresses included in 172.16.0.0/19 in area 0?
31Which two statements are true regarding link-state routing protocols? (Choose two.)
They do not work well in networks that require special hierarchical designs.
They pass their entire routing tables to their directly connected neighbors only.
32
Refer to the exhibit. RIPv1 has been used as a routing protocol on the network. A
new 172.16.2.0/24 network has been added on router R2 and configured under the
RIP routing process. When will R1 converge?
after 13 seconds
after 30 seconds
Refer to the exhibit. The command ip route 0.0.0.0 0.0.0.0 S0/0/0 is run on router
R2. What are the two results of this command? (Choose two.)
The route will be specified as the default route for all networks not defined in the
routing table.
All the broadcasts will be forwarded via the S0/0/0 interface of R2.
34Which three statements are true regarding the encapsulation and de-encapsulation
of packets when traveling through a router? (Choose three.)
The router changes the source physical address to the physical address of the exit
interface.
The router sends the packet out all other interfaces, besides the one it entered the
router on.
35
Refer to the exhibit. RTB is assigned Priority 10 and all other routers use the default
priority setting. How will OSPF select the DR on network 10.10.8.4/30?
The router with the highest priority will become the DR.
The router with the highest IP address will become the BDR.
The router with the highest loopback address will become the DR.
36
Refer to the exhibit. What information can be determined from the highlighted
output?
Refer to the exhibit. Hosts on the BOS Fa0/0 LAN are able to ping the Fa0/1
interface on the JAX router and all interfaces on the BOS and ORL routers. Why
would hosts from the 10.0.0.0/24 network not be able to ping hosts on the Fa0/0 LAN
of the JAX router?
The JAX router needs the network 10.0.0.0 0.0.0.255 area 0 command.
The JAX router needs the network 192.168.3.0 0.0.0.255 area 0 command.
The BOS router needs the network 192.168.3.0 0.0.0.255 area 0 command.
Refer to the exhibit. The network has three connected routers: R1, R2, and R3. The
routes of all three routers are displayed. All routers are operational and pings are not
blocked on this network.
from R1 to 172.16.1.1
from R1 to 192.168.3.1
from R2 to 192.168.1.1
from R2 to 192.168.3.1
40
Refer to the exhibit. A static route was configured on router R1 to forward packets to
the remote networks. During a network upgrade, the network administrator
configured RIPv2 on all routers in the network. What will router R1 do with a packet
that is sourced from PC1 and destined for PC3?
The packet will be forwarded out the Serial0/0/0 interface via the static route.
The packet will be forwarded out the FastEthernet0/1 interface via the static route.
The packet will be forwarded out the Serial0/0/0 interface via the route that is learned
through RIP.
The packet will be forwarded out the FastEthernet0/1 interface via the route that is
learned through RIP
41
Refer to the exhibit. A company uses static routing for its internal network. The
network administrator at the HR branch decides to modify the static routes by adding
two commands ip route 172.16.1.0 255.255.255.0 serial 0/0/0 and ip route
172.16.3.0 255.255.255.0 serial 0/0/0 on the HR router. What is the effect in the
running configuration after adding these two commands?
The original two static routes will be replaced by two new static routes.
Only the two original static routes will appear. The two new static routes will be
discarded.
The two new static routes will not appear in the configuration, but are kept in the
database as backup.
42
Refer to the exhibit. All routers are running the same routing protocol. Based on the
exhibit and its displayed commands, which statement is true?
The network address for the connection to the ISP is not advertised by the routing
protocol process.
43
Refer to the exhibit. Which three statements are true of the routing table for Router1?
(Choose three.)
The AD of EIGRP routes has been manually changed to a value other than the
default value.
Refer to the exhibit. What happens to a packet that has 172.16.0.0/16 as the best
match in the routing table that is shown?
Router>
Router#
Router(config)#
Router(config-if)#
46
Refer to the exhibit. Which two routes are child routes? (Choose two.)
10.0.0.0
10.1.2.0
10.2.2.0
192.168.1.0
192.168.2.0
47
Refer to the exhibit. Routers R1 and R3 use different routing protocols with default
administrative distance values. All devices are properly configured and the
destination network is advertised by both protocols.
Which path will be used to transmit the data packets between PC1 and PC2?
The traffic will be load-balanced between two paths — via R2-R1 and via R2-R3.
The packets will travel via R2-R3, and the other path via R2-R1 will be retained as
the backup path.
48What are two tasks that must be completed before two routers can use OSPF to form
a neighbor adjacency? (Choose two.)
49
Router1
Router2
Router3
Router4