Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
53. If the induction motor speed at no-load is 745 RPM, what is the speed of the motor:
a. 700 RPM
b. 750 RPM
c. 800 RPM
d. 850 RPM
54. What are the types of losses
a. Armature losses
b. Winding losses
55. Op-amp (operational amplifier) input resistance:
a. Zero
b. Infinity
c. Relative resistance
d. Same output resistance.
56. Which of the following devices has a metal–semiconductor junction formed between a
metal and a semiconductor:
a. schottky diode
b. zener diode
c. varactor diode
d. tunnel diode
57. Inverter allowed noise level question given the values of VOH, VOL, VIH, VIL. And need to
get NMH and NML
NMH = VOH – VIH
NML = VIL – VIH
Make sure both are >0
58. Which of the transmission voltage is not applied in Qatar Electrical Specs:
a. 66KV
b. 132KV
c. 220KV
d. 400KV
59. CMOS inverter is superior to the R-pull up inverter due to:
a. High impedance
b. Smaller propagation delay
c. Symmetric transfer characteristics
60. Ultrasound test used to determine
a. Cracks
b. Position of cracks
c. Length of cracks
d. All of above
61. A passive filter can
a. filter only
b. filter & amplify only
c. amplify only
d. none of the above
62. Wireless receiver?
a. power amplifier
b. differential amplifier
63. In receiver and transmitter. Which kind of amplifier used.
a. Power amplifier
64. Major factor that has to be considered when designing a distribution system is
a. Efficiency
b. Voltage Regulation
c. PF
d. Reliability
65. To get rid of DC offset use?
a. Low pass filter
b. high pass filter
c. Band pass filter
d. Stop band pass filter
66. For forward biasing
a. Anode 3v cathode 7v
b. Anode 5v cathode 3v
c. Anode 7v cathode 10v
67. Transformer resistivity
a. High voltage higher than low voltage
b. High voltage lower than low voltage
c. High voltage equal to low voltage
68. Amplifier working with good gain in?
a. Reverse region
b. Cutoff region
c. Active region
d. Saturated region
69. What is wrong sentence
a. Donor N Type
70. What is MOSFET
a. Transistor
b. Thyristors
c. Amplifier
71. What is the efficiency of BJT = IC/IB
72. What is the power consumption of BJT
a. 15%
73. Alternator connected on no load condition, what affect the efficiency.
a. Speed
b. Voltage
c. Armature losses
74. Transformer saturation
a. High efficiency, low no load losses.
b. Low efficiency, low no load losses.
c. Low efficiency, high no load losses.
d. High efficiency, high no load losses.
75. To minimized loading effect use?
a. Resistance
b. Capacitors.
c. Inductors.
76. Best type of switchgear
a. SF6
b. VCB
c. OCB
d. ACB
77. What is least influential in projects?
a. Time
b. Materials
c. Manpower.
78. Which one of the following has High input Impedance?
a. NPN-BJT.
b. PNP-BJT.
c. MOSFET.
d. Both BJT & MOSFET.
79. Ripple Factor of Zener Diode Depends on:
a. Zener Voltage
b. I/P Impedance
c. O/P Impedance
d. None of the above
80. I/P side of the GSM Network should contain?
a. Low Pass Filter
b. High Pas Filter
c. Band Pass Filter
d. None of the above.
81. Power Consumption in the advanced embedded system is
a. 10%
b. 50%
c. 80%
d. None of the above.
82. Power Consumption in Advanced Embedded can be reduced by using
a. Pipe Lining.
b. Voltage sensing
c. Parallelizing
d. None of the above
83. A 4pole Alternator runs in 750 rpm, what is the frequency?
a. 50 HZ
b. 25Hz F=P*N/120
c. 60Hz
d. None of the above
84. Earth Electrode shall be placed in an earth pit?
a. Vertical
b. Horizontal
c. Any Angle
85. Which of the following is a weak power system?
a. Power system with high short circuit capacity and high sensitivity to harmonics
b. Power system with high short circuit capacity and low sensitivity to harmonics
c. Power system with low short circuit capacity and high sensitivity to harmonics
d. Power system with low short circuit capacity and low sensitivity to harmonics
86. Once the transformer is saturated its no load current will be
a. Increases
b. Decreases
c. no change
d. Cancelled
87. Lower current frequency of an NPN transistor depends on
a. Input Imp
b. OP/P imp
c. System Voltage
d. All of the above
88. Harmonics in a system is mainly due to:-
a. Variable Imp Load
b. Saturated magnetic load
c. Power Electronics Load
d. All of the above
89. When I current is passing through R resistance for a time period of t seconds, then the
electrical energy generated will be:
a. I2Rt
b. IR2t
c. 2IRt
d. IR2/t
90. Digital codes only two input
a. True
b. False
91. Ohm’s Law (the right one is U=RI, they put choices not related to this law)
92. The best mix around an earth electrode (Lime sand mixture? Coal & Salt? Etc the right
choice is sand mixture with copper mulch)
93. In case of Transformer saturation how the efficiency and the no load current will behave?
(efficiency decrease and current output is similar to the magnetic field in the transformer
and chopped with notches)
94. What is the circuit breaker application? Its basic function is to detect a fault condition and
interrupt current flow.
95. Synchronous speed for motor 8000 RPM , 50Hz, calculate number of poles.
96. Synchronous speed for motor 8000 RPM , rotor speed 7500 RPM calculate slip.
b) change cost
c) change time
a) leading PF
b) lagging PF
c) Zero PF
d) unity PF
a. Increase in frequency
b. Decrease in frequency
c. Increase in voltage
d. Decrease in voltage
e. Over speed
f. Under speed
g. Leading power factor
h. Lagging power factor
10. Induction motor running at asynchronous speed the torque will be
a- low
b High
c- 0
i. Negative
j. Positive
k. Zero
l. Non
a- Heat
b- Distortion to the signal.
c- .
d- .
e- All the above
&
5- In case of Transformer saturation how the efficiency and the no load current will behave?
(efficiency decrease and current output is similar to the magnetic field in the transformer
and chopped with notches)
6- Ohm’s Law (the right one is U=RI, they put choices not related to this law)
7- The best mix around an earth electrode (Lime sand mixture? Coal & Salt? Etc the right
choice is sand mixture with copper mulch)
8- The best place to build an exhibition and convention center (near the Airport? Or in satellite
place far from Urban? Etc)
9- What is the circuit breaker application? Its basic function is to detect a fault condition and
interrupt current flow.
10- Power transformers are generally designed to have maximum efficiency around:
a- No load
b- half load
c- near full load
d- over load
11- Which breakers used as the main circuit breakers of power distributions in buildings:
a- ACB
b- VCBs
c- oil circuit breakers
15- Minimum cross sectional area of earth continuity conductor in buildings used:
a- 20 AWG
b- 16 AWG = 1.5 mm2
c- 12 AWG
d- 10 AWG
17- For power factor correction of power systems which one is used:
a- capacitor
b- inductor
c- resistors
20- High voltage winding of transformer has ---------- resistivity than the low voltage side.
a- Lower
b- Higher
c- Equal
d- Lower or Equal
23- ABET stands for Accreditation Board for Engineering and Technology?
a- True
b- False
25- If the induction motor speed at no-load is 745 RPM, what is the speed of the motor:
a- 700 RPM
b- 750 RPM
c- 800 RPM
d- 850 RPM
27- If a sudden excitation happens to the alternator what will be its effect:
a- Variation in real power on load side.
b- Variation in apparent power on load side.
c- Power factor effects.
d- The frequency of the generated wave form will be affected.
29- For an inverter op-amp, what will be the equivalent output resistance?
a- Zero
b- Infinity
c- Relative forward resistance
d- Same as the input resistance.
30- Which of the following devices has a metal–semiconductor junction formed between a
metal and a semiconductor:
a- schottky diode
b- zener diode
c- varactor diode
d- tunnel diode
31- The heat loss inside a straight conductor is 60J upon applying current I for 5s. if the
resistance of the conductor is decease to half, and the same current is applied for 5s, what
will be the heat dissipation:
a- 60J
b- 30J
c- 15J
d- 120J
33- The forward pass review of the project management will indicate the following:
a- The earliest start of the task
b- The earliest finish of the task
c- Critical path (longest path)
d- Only A & B
e- All of the above
34- The back pass review of the project will indicate the following:
a- The latest start of the task.
b- The earliest finish of the task.
c- The critical path.
d- Only A & C
e- All of the above.
35- Invertor allowed noise level question given the values of VOH, VOL, VIH, VIL. And need to
get NMH and NML
36- Which of the transmission voltage is not applied in Qatar Electrical Specs:
a- 66KV
b- 132KV
c- 220KV
d- 400KV
13. The load resistance for the Cascade amplifier is (it should be the i/p impedance)
a. The resistance after first stage
b. The resistance before first stage
c. The resistance after second stage
d. The resistance before second stage
15. What is the change order (1)change in scope (2)change in time (3)change in cost and
budget
a. 1&3
b. 2&3
c. 1&2
d. Any change in the work
17. What is the main reason for harmonic in the electrical circuits
a. Impedance
b. Inductance loads
c. Capacitance loads
d. Power electronics loads
19. Which one of the following is suitable for engineering work “Decision shall be based on reason
than situation ’’
a. Quantity Thinking.
b. Logical Thinking.
c. Interpersonal Skills.
d. Honesty
25. The Incandescent Lamp will work normally with best efficiency if the power factor is
a. unity
b. 0.5 leading
c. 0.5 lagging
d. Any power factor
26. The compound which will be used around the earth rod is
a. SE salt and sand
b. E Carbon dust with sand
c. Metal with sand
d. Coral salt with sand
A small problem where u have to determine the number of poles of a synchronous motor, if
you know the pulsation ws (rad/sec) & speed Ns (RPM) and the frequency f (Hz)
&
41- In case of Transformer saturation how the efficiency and the no load current will behave?
(efficiency decrease and current output is similar to the magnetic field in the transformer
and chopped with notches)
42- Ohm’s Law (the right one is U=RI, they put choices not related to this law)
43- The best mix around an earth electrode (Lime sand mixture? Coal & Salt? Etc the right
choice is sand mixture with copper mulch)
44- The best place to build an exhibition and convention center (near the Airport? Or in satellite
place far from Urban? Etc)
45- What is the circuit breaker application? Its basic function is to detect a fault condition and
interrupt current flow.
46- Power transformers are generally designed to have maximum efficiency around:
e- No load
f- half load
g- near full load
h- over load
47- Which breakers used as the main circuit breakers of power distributions in buildings:
d- ACB
e- VCBs
f- oil circuit breakers
51- Minimum cross sectional area of earth continuity conductor in buildings used:
e- 20 AWG
f- 16 AWG = 1.5 mm2
g- 12 AWG
h- 10 AWG
53- For power factor correction of power systems which one is used:
d- capacitor
e- inductor
f- resistors
56- High voltage winding of transformer has ---------- resistivity than the low voltage side.
e- Lower
f- Higher
g- Equal
h- Lower or Equal
59- ABET stands for Accreditation Board for Engineering and Technology?
c- True
d- False
61- If the induction motor speed at no-load is 745 RPM, what is the speed of the motor:
e- 700 RPM
f- 750 RPM
g- 800 RPM
h- 850 RPM
63- If a sudden excitation happens to the alternator what will be its effect:
e- Variation in real power on load side.
f- Variation in apparent power on load side.
g- Power factor effects.
h- The frequency of the generated wave form will be affected.
65- For an inverter op-amp, what will be the equivalent output resistance?
e- Zero
f- Infinity
g- Relative forward resistance
h- Same as the input resistance.
66- Which of the following devices has a metal–semiconductor junction formed between a
metal and a semiconductor:
e- schottky diode
f- zener diode
g- varactor diode
h- tunnel diode
67- The heat loss inside a straight conductor is 60J upon applying current I for 5s. if the
resistance of the conductor is decease to half, and the same current is applied for 5s, what
will be the heat dissipation:
e- 60J
f- 30J
g- 15J
h- 120J
69- The forward pass review of the project management will indicate the following:
f- The earliest start of the task
g- The earliest finish of the task
h- Critical path (longest path)
i- Only A & B
j- All of the above
70- The back pass review of the project will indicate the following:
f- The latest start of the task.
g- The earliest finish of the task.
h- The critical path.
i- Only A & C
j- All of the above.
71- Invertor allowed noise level question given the values of VOH, VOL, VIH, VIL. And need to
get NMH and NML
72- Which of the transmission voltage is not applied in Qatar Electrical Specs:
e- 66KV
f- 132KV
g- 220KV
h- 400KV
MMUP Sample Questions
31. What do we call Synchronous motor working on a lead power factor at no load?
a. Synchronous condenser
b. Reluctance motor
32. A synchronous motor on No-load can be used as:
a. synchronous condenser
b. induction motor
c. induction generator
33. Synchronizing motor leading power factor
a. Synchronic condenser
b. Universal motor
c. Relocating motor
34. Which type of motor used in home ceiling fan:
a. capacitor motor
b. shaded pole motor
c. universal motor
35. Which type of motor used in ceiling fan?
a. Capacitor start type
b. Permanent capacitor run
c. Capacitor induction run.
36. Starting method of IP Motors used in House holding Fans?
a. Capacitor Start
b. Induction start
c. Split phase
d. none of the above
37. Best starting for single phase motor.
a. Connect resistor
b. Connect inductor
c. Connect resistor and inductor in series
d. Connect capacitor.
38. What is the best economical way to start a single phase motor
a. Resistive method
b. Inductive method
c. Capacitive method
d. None of the above
39. Which of the following Braking system is used in the induction Motor?
a. Regenerative Barking
b. Plugging Braking
c. Dynamic Braking
d. All of the above.
40. What one of the below devices is faster and consumes less power in large scale projects?
a. DSP
b. Microcontrollers
c. ASIC
d. FPGA
41. For Fire alarm & smoke detector it is preferable to use
a. Microcontrollers
b. ASIC
c. FPGA
42. Incandescent Lamp flickering due to
a. Voltage
b. Frequency
43. Cascade amplifier is used because
a. High Voltage gain
b. High output impedance
c. High input impedance
44. Cascade amplifier used to reduce load effect, the input impedance will be
a. High
b. Low
c. Medium
45. What is the low-pass filter?
a. It will let pass low frequencies? (or it blocks high frequency)
b. It will let pass high frequencies?
c. It will let pass a band of frequencies?
d. It will eliminate a band of frequencies?
46. What is the role of the zener diode?
a. Rectification
b. Amplification
c. voltage regulation
47. Ohm’s Law (the right one is U=RI, they put choices not related to this law)
48. A synchronous motor at over excited can be used as:
a. Leading power factor
b. Motor unity
c. Motor lagging
49. Voltage regulator negative for synchronous motor
a. Leading power factor
50. What is the QSAS?
a. Qatar Sustainability Assisting Systems
51. For an inverter op-amp, what will be the equivalent output resistance?
a. Zero
b. Infinity
c. Relative forward resistance
d. Same as the input resistance.
52. The heat loss inside a straight conductor is 60J upon applying current I for 5s. if the resistance
of the conductor is decease to half, and the same current is applied for 5s, what will be the
heat dissipation:
a. 60J
b. 30J
c. 15J
d. 120J
53. Breaking for induction motor
a. Regeneration
b. Dynamic
c. Plugging
d. All above
54. Fan out logic gate is
a. Number of gate
b. Number of gate connect to output
55. Type of amplifier at transmitter?
a. Power amplifier
b. Differential Amplifier
56. Loading effect can be reduced in a system by using
a. Integrator
b. Inverted Amplifier
c. Non - Inverted Amplifier
d. Diff Amplifier
57. Transformer humming due to
a. Vibration in Lamination
b. vibration in oil
58. If fuse rate = 8 Ampere, what does mean?
59. First line in transmission
a. Ground
b. R-phase
c. B-phase
d. Neutral
60. Circuit breaker is
a. Current interrupting device
b. Power factor detection device
61. Incandescent lamp operating at a power factor of
a. Leading
b. Lagging
c. Unity
d. Zero
62. Terminal represents control input of BJT
a. Emitter
b. Base
c. Collector
63. Changing in the excitation in grid having an alternator connected to it will having the
following effect
a. Change in active component
b. Change in reactive component
c. No change
64. If a sudden excitation happens to the alternator what will be its effect:
a. Variation in real power on load side.
b. Variation in apparent power on load side.
c. Power factor effects.
d. The frequency of the generated wave form will be affected.
65. Transducers convert physical quantity into
a. Electrical
66. Sensor transducers will transfer.
a. Move to electrical signals
b. Heat to mechanical signal.
67. How much is the slip for synchronous generators
a. Zero
b. Negative
c. positive
68. Difference between inch and centimeter
a. 2.45
b. 2.54
69. Common breakers used in distribution level
a. Air circuit breaker ACB
b. Oil type
c. Vacuum VCB
70. “Question regarding what does an engineer do!”
71. Difference between MOSFET and BJT
a. MOSFET amplifies current
b. BJT is bigger in size and dimensions
72. What is the DC gain of the transistor NPN?
a. The right answer is IC/IB, they put also the formulas of the MOSFET which are
wrong for this question
73. How the diode let pass the current?
a. Only in one way, it will block the other way
74. Power transformers are generally designed to have maximum efficiency around:
a. No load
b. half load
c. near full load
d. over load
75. Minimum cross sectional area of earth continuity conductor in buildings used:
a. 20 AWG
b. 16 AWG = 1.5 mm2
c. 12 AWG
d. 10 AWGk
76. For power factor correction of power systems which one is used:
a. capacitor
b. inductor
c. resistors
77. Terminals of a transistor (BJT):
a. Base, collector & emitter
b. gate, collector & emitter
c. gate, emitter & drain
78. Differential Amplifier with High CMRRS means:
a. High rejection of noise
b. Amplify noise
c. High amplification gain
79. High voltage winding of transformer has ---------- resistivity than the low voltage side.
a. Lower
b. Higher
c. Equal
d. Lower or Equal
80. ABET stands for Accreditation Board for Engineering and Technology?
a. True
b. False
81. What does the power factor stands for:
a. Cosine of the angle between voltage and current.
b. Sine of the angle between voltage and current.
c. Apparent power over real power.
82. Displacement factor
a. Cosine angle between voltage and current
b. sine angle between voltage and current
c. tan angle between voltage and current
d. cotangent angle between voltage and current
83. If the induction motor speed at no-load is 745 RPM, what is the speed of the motor:
a. 700 RPM
b. 750 RPM
c. 800 RPM
d. 850 RPM
84. What are the types of losses
a. Armature losses
b. Winding losses
85. Op-amp (operational amplifier) input resistance:
a. Zero
b. Infinity
c. Relative resistance
d. Same output resistance.
86. Which of the following devices has a metal–semiconductor junction formed between a metal
and a semiconductor:
a. schottky diode
b. zener diode
c. varactor diode
d. tunnel diode
87. Inverter allowed noise level question given the values of VOH, VOL, VIH, VIL. And need to get
NMH and NML
88. Which of the transmission voltage is not applied in Qatar Electrical Specs:
a. 66KV
b. 132KV
c. 220KV
d. 400KV
89. CMOS inverter is superior to the R-pull up inverter due to:
a. High impedance
b. Smaller propagation delay
c. Symmetric transfer characteristics
90. Ultrasound test used to determine
a. Cracks
b. Position of cracks
c. Length of cracks
d. All of above
91. A passive filter can
a. filter only
b. filter & amplify only
c. amplify only
d. none of the above
92. Wireless receiver?
a. power amplifier
b. differential amplifier
93. In receiver and transmitter. Which kind of amplifier used.
a. Power amplifier
94. Major factor that has to be considered when designing a distribution system is
a. Efficiency
b. Voltage Regulation
c. PF
d. Reliability
95. To get rid of DC offset use?
a. Low pass filter
b. high pass filter
c. Band pass filter
d. Stop band pass filter
96. For forward biasing
a. Anode 3v cathode 7v
b. Anode 5v cathode 3v
c. Anode 7v cathode 10v
97. Transformer resistivity
a. High voltage higher than low voltage
b. High voltage lower than low voltage
c. High voltage equal to low voltage
98. Amplifier working with good gain in?
a. Reverse region
b. Cutoff region
c. Active region
d. Saturated region
99. What is wrong sentence
a. Donor N Type
100. What is MOSFET
a. Transistor
b. Thyristors
c. Amplifier
101. What is the efficiency of BJT = IC/IB
102. What is the power consumption of BJT
a. 15%
103. Alternator connected on no load condition, what affect the efficiency.
a. Speed
b. Voltage
c. Armature losses
104. Transformer saturation
a. High efficiency, low no load losses.
b. Low efficiency, low no load losses.
c. Low efficiency, high no load losses.
d. High efficiency, high no load losses.
105. To minimized loading effect use?
a. Resistance
b. Capacitors.
c. Inductors.
106. Best type of switchgear
a. SF6
b. VCB
c. OCB
d. ACB
107. What is least influential in projects?
a. Time
b. Materials
c. Manpower.
108. Which one of the following has High input Impedance?
a. NPN-BJT.
b. PNP-BJT.
c. MOSFET.
d. Both BJT & MOSFET.
109. Ripple Factor of Zener Diode Depends on:
a. Zener Voltage
b. I/P Impedance
c. O/P Impedance
d. None of the above
110. I/P side of the GSM Network should contain?
a. Low Pass Filter
b. High Pas Filter
c. Band Pass Filter
d. None of the above.
111. Power Consumption in the advanced embedded system is
a. 10%
b. 50%
c. 80%
d. None of the above.
112. Power Consumption in Advanced Embedded can be reduced by using
a. Pipe Lining.
b. Voltage sensing
c. Parallelizing
d. None of the above
113. A 4pole Alternator runs in 750 rpm, what is the frequency?
a. 50 HZ
b. 25Hz
c. 60Hz
d. None of the above
114. Earth Electrode shall be placed in an earth pit?
a. Vertical
b. Horizontal
c. Any Angle
115. Which of the following is a weak power system?
a. Power system with high short circuit capacity and high sensitivity to harmonics
b. Power system with high short circuit capacity and low sensitivity to harmonics
c. Power system with low short circuit capacity and high sensitivity to harmonics
d. Power system with low short circuit capacity and low sensitivity to harmonics
116. Once the transformer is saturated its no load current will be
a. Increases
b. Decreases
c. no change
d. Cancelled
117. Lower current frequency of an NPN transistor depends on
a. Input Imp
b. OP/P imp
c. System Voltage
d. All of the above
118. Harmonics in a system is mainly due to:-
a. Variable Imp Load
b. Saturated magnetic load
c. Power Electronics Load
d. All of the above
119. When I current is passing through R resistance for a time period of t seconds, then the
electrical energy generated will be:
a. I2Rt
b. IR2t
c. 2IRt
d. IR2/t
120. Digital codes only two input
a. True
b. False
121. Ohm’s Law (the right one is U=RI, they put choices not related to this law)
122. The best mix around an earth electrode (Lime sand mixture? Coal & Salt? Etc the right
choice is sand mixture with copper mulch)
123. In case of Transformer saturation how the efficiency and the no load current will behave?
(efficiency decrease and current output is similar to the magnetic field in the transformer and
chopped with notches)
124. What is the circuit breaker application? Its basic function is to detect a fault condition and
interrupt current flow.
125. Synchronous speed for motor 8000 RPM , 50Hz, calculate number of poles.
126. Synchronous speed for motor 8000 RPM , rotor speed 7500 RPM calculate slip.
127. If you were awarded a project, you will start work:
a. One week before the approval of the authorities
b. After the approval of the authorities
c. One day before the approval of the authorities
128. To minimized loading effect used.
a. Inverter amplifier
b. Non inverter amplifier
c. Integrator
129. Scope Management starts with is:
a. To identify the client requirements
b. Meet the team
c. Review strategic plan
130. Wire placed on the top of a transmission line.
a. Ground wire
b. Neutral wire
c. Phase wire
101. Final as built drawings for what purpose
a. To keep record for later maintenance
b. To give more work to architect
c. To be used for further renovation
102. Control department work starts
a. From the beginning of the project
b. During construction
c. After construction
103. “There was a question regarding the lowest hierarchy in WBS” I couldn’t remember the
options 104. Length of a line shown in a map is 7 ¼” long and it’s scale is 1:62500, then what will
be the actual distance indicated by that line in miles.
a) 8.3
b) 7.5
c) 11.29
d) None of the above
105. Which of the following systems uses “Assembly language”
a) SCADA
b) Microcontrollers
c) ASIC
d) FPGA
e) Both A&B
106. BJT will act as a switch in which region?
a) Ohmic Region
b) Saturation Region
c) Active Region
d) Passive Region
107 If Water to cement ratio used in a residential building higher , then what will be the effect
on building
a) Strength will be low
b) Strength will be high
c) Pouring will be faster
d) Pouring will be Slower
e) No effect
108. A synchronous generator running at a speed of 1200 rpm and it ‘s frequency is 100HZ ,
then what will be quantity of poles used in that generator ?
a) 8
b) 10
c) 12
d) 4
109. What will be the effect in system, if we over-excite a synchronous generator?
a) unity Power factor
b) Lagging Power factor
c) Leading Power Factor
d) M/C will stop
110. Incandescent lamp operating at a power factor of
a) 1
b) 0.8 lagging
c) 0.9 leading
d) 0
111. In what situation we can claim for a change order from the client
a) When client want to add something which is not available in initial scope
b) When major change occurs due to site conditions
c) Design mistake or Error
d) All of the above
112. Humming happening in a Transformer due to
a) Due to the Vibration in brush
b) Due to magnetostriction in core laminations
c) Due to the Vibration in winding
d) None of the above
e) All of the above
113. For an inverter op-amp, what will be the equivalent output resistance?
a) Relative forward resistance
b) Infinity
c) 0
d) Same as the input resistance
e) None of the above
114. In order to have minimum loading effect, output impedance of a cascade amplifier must be
a) High
b) Low
c) Medium
115. The starting capacitor of a single-phase motor is
a) Electrolytic type
b) Ceramic type
c) Paper type
d) None of the above
116. The staring torque of a capacitor start motor is
a) 0
b) Low
c) Same as rated torque
d) More than rated torque
117. Which one will be true for an active filter
a) filter only
b) filter & amplify only
c) amplify only
d) none of the above
118. Surge voltage originate in a power system due to
a) Lightning
b) Switching operations
c) Faults
d) Any of the above
119. Which motor is generally used for electric shavers
a) Reluctance motor
b) Shaded pole motor
c) Hysteresis motor
d) Universal motor
120. The term “Pipe lining” is used to indicate
140. What is the change order (1)change in scope (2)change in time (3)change in cost and
budget
e. 1&3
f. 2&3
g. 1&2
h. Any change in the work
142. What is the main reason for harmonic in the electrical circuits
e. Impedance
f. Inductance loads
g. Capacitance loads
h. Power electronics loads
144. Which one of the following is suitable for engineering work “Decision shall be based on
reason than situation ’’
e. Quantity Thinking.
f. Logical Thinking.
g. Interpersonal Skills.
h. Honesty
150. The Incandescent Lamp will work normally with best efficiency if the power factor is
e. unity
f. 0.5 leading
g. 0.5 lagging
h. Any power factor
151. The compound which will be used around the earth rod is
e. SE salt and sand
f. E Carbon dust with sand
g. Metal with sand
h. Coral salt with sand
Dear all,
Please find the below questions I have received during UPDA examination
1. what is the step from the below which not related to project steps.
a) concepts
b) initiation
c) planning
d) hand over
e) scheduling
a) SCADA
b) Microcontrollers
c) ASIC
d) FPGA
e) Both A&B
3. What will be the output impedance of cascade amplifier to minimizes the loading effect.
a) High
b) Low
c) Intermediate
d) No effect
4. uninterruptable power system has to be connected to the network by.
5. what is the purpose for the neutral line at the 3 phase power system.
6. An Engineer received new scope of work which is not included at the original scope,
what the action he has to do:
a) power amplifier
b) diff. amplifier
c) active filter
132KV
220KV
400KV
a) Neutral
b) Phase
c) Ground
a) change scope
b) change cost
c) change time
a) Vertical
b) Horizontal
c) Any Angle
12. What one of the below devices is faster and consumes less power in large scale projects?
DSP
Microcontrollers
ASIC
FPGA
14 High voltage winding of transformer has ---------- resistivity than the low voltage side.
Lower
Higher
Equal
Lower or Equal
High impedance
16. What do we call Synchronous motor working on a lead power factor at no load?
Synchronous condenser
Reluctance motor
O/P imp
System Voltage
a) 0
b) Low
d) both A&B
It is small antenna
It is large antenna
a. Zener voltage
b. I/P Impedance
c. O/P Impedance
Motor unity
Motor lagging
a) leading PF
b) lagging PF
c) Zero PF
d) unity PF
256. Which of the following Braking system is used in the induction Motor?
a. Regenerative Barking
b. Plugging Braking
c. Dynamic Braking
d. All of the above.
257. What is the role of the zener diode?
a. Rectification
b. Amplification
c. voltage regulation
258. The Incandescent Lamp will work normally with best efficiency if the power factor is
i. unity
j. 0.5 leading
k. 0.5 lagging
l. Any power factor
259. Before starting work at site, the major factor has to be checked is?
a. Access to site (EFE)
b. Storage of Water, tools & equipments
c. Safety
d. Approval from MMUP / Civil / Defence etc.
e. All of the above
260. First line in transmission
a. Ground
b. R-phase
c. B-phase
d. Neutral
261. What is the efficiency of BJT = IC/IB
262. Cascade amplifier used to reduce load effect, the input impedance will be
a. High
b. Low
c. Medium
263. What is the low-pass filter?
a. It will let pass low frequencies?
b. It will let pass high frequencies?
c. It will let pass a band of frequencies?
d. It will eliminate a band of frequencies?
264. Which of the following devices has a metal–semiconductor junction formed between
a metal and a semiconductor:
a. schottky diode
b. zener diode
c. varactor diode
d. tunnel diode
17. Minimum cross sectional area of earth continuity conductor in buildings used:
a. 20 AWG
b. 16 AWG
c. 12 AWG
d. 10 AWG
18. Ripple Factor of Zener Diode Depends on:
a. Zener Voltage
b. I/P Impedance
c. O/P Impedance
d. None of the above
19. Transformer saturation
a. High efficiency, low no load losses.
b. Low efficiency, low no load losses.
c. Low efficiency, high no load losses.
d. High efficiency, high no load losses.
20. Before starting work at site, the major factor has to be checked is?
a. Access to site (EFE)
b. Storage of Water, tools & equipments
c. Safety
d. Approval from MMUP / Civil / Defence etc.
e. All of the above
1- Induction motor operating at frequency of 50HZ, and no load speed 2900 RPM. What is the
slip frequency
a- 0.33 HZ
b- 1.67 HZ
2- When using Zener diode for voltage regulation, the output waveform shape will be affected
by
a- Dynamic resistance of the diode
b- Input current passing through the diode
13. Sensor transducers (temperature, motion, etc ) will transfer to what type of signal
a. electrical signals
b. mechanical signal.
14. If an induction motor at 50 Hz, has a speed at no-load of 745 RPM, what will be the
synchronous speed of the motor:
a. 700 RPM
b. 750 RPM
c. 800 RPM
d. 850 RPM
19- Induction motor running with steady rotor(non rotating), the slip will be
c- 1
d- 0
1- Active region
2- Ohmic region
3- Cut-off region
21- A synchronous generator running at a speed of 1200 rpm and frequency of 100HZ , then
what will be quantity of poles used in that generator ?
a) 8
b) 10
c) 12
d) 4
a. Root estimation
b. Assembled
c.
d.