Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Service Manual
Amplifier
Power (RMS): 250 Watts
Driver: 300mm (12") PolyPlas
Inputs: Line Level (switchable to LFE)
and Speaker Level with
5-way binding posts
Outputs: Speaker Level, High-Pass
5-way binding posts
Low-Pass
Frequency: Continuously variable
from 50Hz – 150Hz
High-Pass
Frequency: 150Hz when using
speaker-level output
Frequency
Response: 25Hz – low-pass
crossover setting
Dimensions
(H x W x D): 500mm x 365mm x 435mm
Weight: 20.1kg
14,15,16
2,3
17
7 24
11
19
1
9
23 1
6,20
21
12
10
18
4
8,13
5
Testing Procedure
With a 5mV signal to Low level input, LED should change to GREEN
OP AMP
LED P-U4(1) P-U4(7)
RED 0Vrms 11.84VDC
GREEN 7.13Vrms -12.93VDC
3. D.C. Operation
Between V+ Q4(E) Q1(C) Q10(C) U7(1) U7(2) U7(4) U7(6) U7(7) U7(8)
And This
GND V- GND GND GND GND GND GND GND GND
Point
Get this
71.7V 0V -71.7V 0V -71.7V -71.5V -71.2V 0V 0V 4.65V
Reading
-Set up Turn level, X’OVER FREQ POT Fully CW and LFE switch off
Generator Set at 200mV@50Hz
Signal to Line level input
E250P
Testing Procedure
- Voltage measurements
OP AMP SPEAKER
U2(1) U2(14) U2(8) U3(7) U3(1) U3(14) U3(8) U5(7) U5(1) O/P
306.9mV 461mV 460mV 658mV 628mV 598mV 2.326V 2.02V 3.57V 23.33V
3. Low-Pass
-Voltage measurement
4. LFE
Testing Procedure
POWER MODULE TESTING FLOW CHART
CAUTION : SPEAKER OUTPUT IS FLOATING AND IS NOT PROTECTED AGAINST A SHORT
TO GROUND. ALL TEST INSTRUMENTS CONNECTED TO THE OUTPUT MUST
BE FLOATING. ATTACH THE SCOPE PROBE TIP TO S - and REFERENCE
LEAD TO S+.
(A 10mV signal may need from the input to trigger the Switch turn on)
START
Resistance check
(no load)
between V+ V-, Check +/-15V-MOD
V+ O/P,V- O/P +/-15V voltage at
and O/P to GND U 6(8),U6(4)
is > 10K
Check
no FB1,FB2,C45,
no OK C50,C60,C63,
Replace
R81,R82
OK Q18,Q22
yes
yes
I/P:10mv/50HZ
Power up with no Check +15V/SW
signal input Q4(E) TO V-
LED RED 15V
no
no Discharge C37, OK
Check
Check fuse MUTE(-12.9V),
OK transformer, L4, And
yes
yes rectifier, C6 and C8 Q24,Q25,Q26
Check
Check Q4(E) U7(1) = -58.3V
TO V-
= 0V D.C.
no Check
no Check OK U7,Q16,Q17,
OK MUTE(+8V) and Q20,Q21,R87,
Q24,Q25,Q26 yes D26,D35,C64
yes
Use scope to
Use scope to check check O/P U7(6)
switching and GND
frequency U6(7) 143Vp-p square
100KHz wave shown
+/-10% , ~24Vp-p
no
OK
no
OK yes
yes Check
L2,L3,C71,C72,
CLASS D AMP OK C73,C74
END
Block Diagram
1 2 3 4 5 6 7 8
RevNo Revision note Date Signature Checked
A A
Rin
VOLUME CTRL
Lout
LFE
Line Level LIMITER / SUMMI NG AMP
Input LPF
DC OFFSET
PROTECTION
NORMAL
C SIGNAL SENSE C
THERMAL
PROTECTION
MUTE
ATO CURRENT
SIGNAL SENEING PROTECTION
MUTE
D * FUSE LINEAR
D
POWER SUPPLY
CLASS D
AMPLIFIER OUTPUT-RELAY
5.6 OHMS
NOTE :
120 VAC T2A-250V
F 230 VAC T1.25A-250V F
1 2 3 6 7 8
E250P
2 1. G
Base 2. D
3. S
1 Emitter
1
2
3
MPSW06RLRA,
1 2 3
MPSW56RLRAMPQ,
MPS2222ARLRA,
2N2907A, 2N5551, OPAMP, DUAL
TIP31C
Q2, 16, 3, 21, 19, 23, 17 TL072CDR SO-8,
Q4
NJM4558M-TE3
U5, 6, 4
3 Collector
2
Base
1 Emitter
1 BEVEL
2 3
MMBT3904LTI SOT23,
MMBT3906LTI SOT23, B C E