Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Operating Manual
Type : EN-RMC
Over view
EN-RMC Series Ring Main Circuit Breaker is pad mounted fully deadfront switchgear for up to 12kV, 630A
underground system, combining disconnect switches and vacuum fault interrupters.
EN-RMC series switchgear incorporates disconnect switches for every ways to provide added safety
and faster operation.
Every bushing in this switchgear is installed with CTs and voltage sensor each, so all the electrical
values of connected distribution system can be measured.
EN-RMC series Ring Main Circuit Breaker has been fully certified in accordance with IEC 62271-100
to meet and exceed customer specifications.
Design
The EN-RMC Ring Main Circuit Breaker is a non-extensible ring main unit comprising of 4 feeders in
one common stainless steel tank.
The unit is suitable for outdoor applications and can be used either as a freestanding unit or
installed in compact mini-substations.
Circuit Breaker
The circuit breaker comprises of three vacuum interrupters, which have a fault-make, fault-break rating.
Opening of the circuit breaker is achieved by opening of the manually operating push button or openig electrical
push button or via signal of the protection relay.
Motoried spring charge mechanism for Circuit Breaker.
Operation
All operating positions and instructions are indicated on the main panel at the front of the unit.
Operation is by means of manually independent mechanisms, which are mounted external to the main enclosure.
Deadfront design and mechanical interlock between main and earth switch provides a high level of safety and
efficient maintenance.
Typical uses
Simple outdoor substation, customer transformer substations and distribution substations
Industrial plants and underground stations
Highly Reliability
At atmospheric gas pressure, it ensure the rated insulation and interruption capabilities.
Pure puffer techniques, no leakage current path between open contacts.
Switchgear vessel made of stainless steel
Maintenance-free concept
SF6 gas insulation and vaccum interruption.(circuit breaker)
Sealed pressure system
Climate-independent
Safety
Operation interlock at front panel
Safe-to-touch and hermetically sealed enclosure
HV parts are only accessible when outgoing feeders are earthed
Overpressure relief device
Pad lock
Easy installation and operation
The speed of close/open is independent of the speed of lever movement.
Ratings
Nominal voltage 11kV
Rated voltage 12kV
Rated frequency 50Hz
Number of phases 3
Mechanical endurance 2000CO
Rated lighting impulse withstand voltage 95㎸
Rated short duration power frequency withstand voltage 28㎸
Rated short time withstand current 25kA for 3seconds
Short circuit breaking current 25kA
Rated normal current 630A
Leak rate Less than 0.1% per year
Rated filling pressure 0.03 Mpa
Protection class IP56
Features - Front view RMC 6107.M0 3 / 19
Front view
Ring main Circuit breaker
3-Position off-load disconnector
Voltage detection system
Ergonomic mimic diagram
Vacuum interrupters for circuit breaker
Common stainless steel chamber
Full insulation ratings at zero atmospheric pressure
Side view
Cable box(rear side)
Cable test bushing(upper side)
All parts of the main circuit is inside SF6 tank except cables and CTs.
Provision for cable termination is made through seal off bushings at the bottom of switchgear
on the same height, parallel , on equal distance as from the ground and is accessible from the rear of
the RMU and protected by cable box covers. Ring type CTs to be assembled on the seal off bushings.
Features - Operating panel RMC 6107.M0 5 / 19
Operating panel
Voltage indicator
Red led blinks if high voltage present at main bushing
Capacitive voltage divider in bushings supply the power of voltage indicator
Installed on every operating panel
Definition of Status
There are 3 status of RMU.
1. Close status: Busings and common bus bar is connected electrically.
2. Open status: Busings and common bus bar is disconnected electrically.
3. Earth status: Busings and earth bushing is connected electrically.
Interlock
DS cannot operated when CB is ON position.
To operate DS, CB must be OFF position first.
CB operation
CB can be operated by manual push button after spring charging completed.
1. Spring Charge: rotate handle clockwise until indicator is turn to "Spring charged".
2. Close: Press "I" button. CB indication will change to Close.
3. Open: Press "O" button. CB indication will change to Open.
Open operation still can be done when spring charge is released condition.
DS operation
DS can be operated only in the CB OFF position. (Push down the interlock lever and insert th DS handle)
Rotate the operating handle in accordance with the arrow direction on the front panel.
In order to make DS switch on after Earth off, the handle has to be taken out and reinserted to operate.
OFF-DS
CW CW
CC CC
DS handle
Operation - Cable box open RMC 6107.M0 9 / 19
CB OFF DS EARTH CB ON
Cable box
lift up the cable box
and separate from RMU
Cable Test
Can be only operated when DS is EARTH position and CB is ON status.
CB OFF → DS EARTH → CB ON
Cover open and disconnect bus bar.
Dimension
Base detail
Installation - Base detail RMC 6107.M0 17 / 19
Base detail
Installation - Protection Pillars RMC 6107.M0 18 / 19
Protection Pillars
3000
1300
1250
625
650
4040
1250
1540
1500
NOTE: