Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
INSTALLATION INSTRUCTIONS
K-8703IN-1WH / K-8700IN-1
VITREOUS CHINA LAVATORY
IMPORTANT INFORMATION
WARNING: Risk of personal injury or product damage. Handle with care.
Vitreous China can break or chip if the bolts and nuts are over-tightened, or if the product is handled carelessly.
ORDERING INFORMATION
Brive+ Wall-Mount Lavatory..............K-8703IN-1WH* Brive+ Pedestal Lavatory............................K-8700IN-1*
Includes Wall-Mount Lavatory.................K-8703IN-1WH*
Includes Pedestal...................................K-8705IN*
* Available in “-0 (White)” & “-96 (Biscuit)”
ROUGHING-IN
2 For Wall-Mount Lavatory Installation For Pedestal Lavatory Installation
(K-8703IN-1WH*) (K-8700IN-1*)
19-7/16" 19-7/16"
(49.4 cm) (49.4 cm) 2-3/4" (7 cm)
2-3/4" (7 cm)
21-1/4" 21-1/4"
(54 cm) (54 cm)
8-5/8" 8-5/8"
1-3/4" (22 cm) 1-3/4" (22 cm)
(4.3 cm) Anchor Holes (4.3 cm) Anchor Holes
ŸAll dimensions in inches (cm). Fixture dimensions are nominal and conform to tolerances as per ASME Standard A112. 19.2M.
ŸProduct illustrations shown are representative only; actual products may vary.
ŸKohler reserves the right to make changes in product characteristics, packaging or availability at any time without notice.
CAUTION : Do not use lime/cement to install the lavatory. The expansion of lime/cement due to rise in temperature may
cause the lavatory to crack or be damaged. Kohler is not responsible for any damage caused by installation with the use
of lime/cement.
1213118-IN01-C -1-
INSTALLATION GUIDELINE
1. Prepare the Site :-
• Rough-in the supplies & the drain piping. For dimensions, Refer Fig.#2.
• Install 1/2" water supply lines & 1-1/4" drain piping according to the roughing-in information.
• Install sufficient backing behind the finished wall to provide a secure material for the anchoring devices.
NOTE :- The Angle-Valve handles cannot extend more than 76mm (3") from the finished wall when in open position. This will
ensure the handles will not touch the pedestal when fully open.
2. Installation of the Lavatory :-
WALL-MOUNT FULL-PEDESTAL
• Drill two Ø14mm Anchor holes on the wall as 3 • Apply two self-adhesive levelling pads (provided) 7
shown in the Rough-in diagram. to each of the three ridges in the bottom recess of the
• Insert the plastic anchors (provided) in two lavatory. Refer Fig. #7
holes.
• Insert the metal studs (provided) into these
• Mark the centerline on the floor with a pencil.
plastic anchors using an adjustable wrench.
• Position the pedestal on the floor centerline location. 8
• Ensure that at least 70 mm (approx.) of each
Refer to the roughing-in dimensions for correct
stud should remain exposed from the wall.
placement.
Refer Fig. #3
• Carefully set the lavatory on the pedestal.
• Move the pedestal as required to ensure proper
fit in the desired location.
Plastic Anchors Pedestal
• Level the lavatory. Use additional self-adhesive
Metal Studs levelling pads as required to level the lavatory.
NOTE :-The lavatory must be supported by the
• Install the faucet & drain to the lavatory 4 pedestal.
Mark Floor
according to the manufacturer’s instructions. • Check the lavatory placement. Here
Center of
NOTE :- Do not fully tighten slip-joint drain • Mark the center of each anchoring hole on the wall. Anchoring Holes
connections at this time. • Carefully remove the lavatory from the pedestal. Then
move the pedestal from the area.
9
Refer Fig. #4
Refer Fig. #8
* Installation doesn't allow use of any tool other than standard wrench. to the faucet. 6-9 turns (45° each) allowed past finger tight
For this reason, split turns have been mentioned rather than full turns.
12
• Evenly put the sealant around the mounting
surface of the lavatory touching the wall.
SERVICE PARTS (Supplied with the Product) • Clean the lavatory top.
A. Hardware Kit 1213117 Refer Fig. #12
B. Levelling Pads 63069
1213118-IN01-C -2-