Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
URUGUAY E-0679
4-258530
COCHABAMBA-BOLIVIA
1080P XTREMREX
LED Backlights
Original February 09, 2010
Updated July 28, 2010
OUTLINE
Preliminary Section:
Contact Information, Preliminary Matters, Specifications,
LCD Overview, General Troubleshooting Steps,
Signal Distribution, Disassembly Instructions and Voltages
Disassembly Section: Removal of Circuit Boards
Troubleshooting Section: Board Operation Troubleshooting of :
• Switch Mode Power Supply
• Inverter Board (LED Backlight Driver)
• T-CON (TFT Controller) Panel Driver board
• Main Board
• Ft Control Board
• Side Keys
• Speakers
Section 1
This Section will cover Contact Information and remind the Technician of Important Safety Precautions for
the Customers Safety as well as the Technician and the Equipment.
Basic Troubleshooting Techniques which can save time and money sometimes can be overlooked. These
techniques will also be presented.
This Section will get the Technician familiar with the Disassembly, Identification and Layout of the LCD
Display Panel.
At the end of this Section the Technician should be able to Identify the Circuit Boards and have the ability
and knowledge necessary to safely remove and replace any Circuit Board or Assembly.
CAUTION
To avoid personal injury, disconnect the power before servicing this product. If electrical power is required for
diagnosis or test purposes, disconnect the power immediately after performing the necessary checks. Also be
aware that many household products present a weight hazard. At least two people should be involved in the
installation or servicing of such devices. Failure to consider the weight of an product could result in physical
injury.
Today’s sophisticated electronics are electrostatic discharge (ESD) sensitive. ESD can weaken or damage
the electronics in a manner that renders them inoperative or reduces the time until their next failure.
Connect an ESD wrist strap to a ground connection point or unpainted metal in the product. Alternatively,
you can touch your finger repeatedly to a ground connection point or unpainted metal in the product. Before
removing a replacement part from its package, touch the anti-static bag to a ground connection point or
unpainted metal in the product. Handle the electronic control assembly by its edges only. When
repackaging a failed electronic control assembly in an anti-static bag, observe these same precautions.
Regulatory Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate
the receiving antenna; Increase the separation between the equipment and the receiver; Connect the
equipment to an outlet on a different circuit than that to which the receiver is connected; or consult the
dealer or an experienced radio/TV technician for help.
LCD-DV: 32LG40, 32LH30, 37LH55, 42LG60, 42LG70, 42LH20, 42LH40, 42LH50, 42LH90, 42SL80,
47LG90, 47LH85, 47LE8500
PLASMA: 42PG20, 42PQ20, 42PQ30, 50PG20, 50PJ350, 50PK750, 50PS80, 50PS60, 60PK750,
60PS11, 60PS60, 60PS80
1. Check the appearance of the Replacement Panel and Circuit Boards for both physical
damage and part number accuracy.
2. Check the model label. Verify model names and board model matches.
3. Check details of defective condition and history. Example: Oscillator failure dead set, etc…
•Define Look at the symptom carefully and determine what circuits could be causing
the failure. Use your senses Sight, Smell, Touch and Hearing. Look for burned parts and
check for possible overheated components. Capacitors will sometimes leak dielectric material
and give off a distinct odor. Frequency of power supplies will change with the load, or listen for
relay closing etc. Observation of the front Power LED may give some clues.
•Localize After carefully checking the symptom and determining the circuits to be
checked and after giving a thorough examination using your senses the first check should
always be the DC Supply Voltages to those circuits under test. Always confirm the supplies
are not only the proper level but be sure they are noise free. If the supplies are missing check
the resistance for possible short circuits.
•Isolate To further isolate the failure, check for the proper waveforms with the
Oscilloscope to make a final determination of the failure. Look for correct Amplitude Phasing
and Timing of the signals also check for the proper Duty Cycle of the signals. Sometimes
“glitches” or “road bumps” will be an indication of an imminent failure.
•Correct The final step is to correct the problem. Be careful of ESD and make sure to
check the DC Supplies for proper levels. Make all necessary adjustments and lastly always
perform a Safety AC Leakage Test before returning the product back to the Customer.
MAIN BOARD
Rear and Side
Input/Output locations
Shows the
Software
Version
found on the
USB Flash
Drive
16-15/16" 9-5/8"
430mm 244mm
14-1/8"
28-3/16"
357.98mm
716.28mm
21" 7-7/8"
Center
533.4mm 200mm
30-5/8"
777.88mm
14-1/8"
357.98mm 10-5/8"
Model No.
270mm
Serial No.
Label Remove 4 screws to
remove stand for
wall mount
2-7/16"
61.6mm
14-3/16"
Weight without Stand: 43 lb 17-7/8"
360.68mm
Weight with Stand: 51.1 lb 454mm
16
DISASSEMBLY SECTION
Disassembly:
This section of the manual will discuss Disassembly, Layout
(Circuit Board Identification) of the 42LH90 LCD Direct View Television.
J.CARLOS RODRIGUEZ
URUGUAY E-0679 Right LED
4-258530
COCHABAMBA
Connection
BOLIVIA Main Board
p/n EBR62151101
Side Keys Side
Inputs
Intelligent AC Input
Sensor / IR Rear Inputs
Tweeter R
CN5 CN4
TFT PANEL
T-CON
CN305 N/C CN2
CN1
CN306
CN307 N/C
INVERTER
SK100
SK101
AC In
IR
P100
Main
Power LED Speakers (Front Right) Speakers (Front Left)
P103 IR P101
P100 LED
J1
20
Power Supply
Board Removal
P203
P201
Disconnect P201
P201, P203,
AC In SK100
and SK101.
Remove the 6
screws indicated Press in
by the arrows. Two tabs
to release
lock
SK
10
0
SK101 AC In
Power
Switch
CN5 CN4
Note: Chocolate
(Heat Sink
Material) CN1 CN2
Note: The tabs are fragile, use caution, they may break.
To remove the flex cables to the TFT Panel, CN4 or CN5, place a soft thin object like a
fingernail underneath the black locking tab and gently pull forward.
Fig 1 Fig 2
Unlocked
Fig 3
Disconnect P3500,
P3501, P3502, P1200, P3500 P3502
P700 and P600
P3501
Disconnect CN1,
CN3, CN4 and CN306.
Remove the Inverter.
CN3 CN4
NOTE: Always check for Chocolate
(Heat Transfer Material).
Be sure to transfer to new Board if present CN1
and replace in the correct position.
There should be 8 pieces on the DC to DC
converter coils near the bottom right.
Chocolate
Chocolate Location
White Box Outline
Key board
p/n EBR62128101
01
P1
P102
Tab
Tab
00
P1
J1
Moving LED board
(Power LEDs)
The Power Switch has
been removed for easier Disconnect J1 or P100. Remove p/n EBR61674001
the LED board by lifting up on
viewing of connectors and the two locking tabs and pull
screws. backwards on the board.
Tab
(A)
Slots
Push In
Tab
Tab
Tab
Slots
(B)
Disconnect
Push In
P100
and remove the
Key Board
Troubleshooting:
This section of the manual will also discuss
troubleshooting.
Type 2: Opens ground to the front IR board. (Stand-By 5V Remains, the Main board stays alive).
This prevents any activity of the IR or the Key Board. When the Switch is opened, a line called Power Key pulls up high
when ground opens. When the switch is closed, this same line called Power Key feeds back to the Microprocessor and the
Micro. Turns on the Power.
Type 3: Opens ground to the front IR board. (Stand-By 5V turns off, the Main board is dead).
This prevents any activity of the IR or the Key Board. When the Switch is opened, a line called Power Key pulls up high
when ground opens. This line feeds back to the Main board and from there it routes to the Power Supply. The high tells the
Controller chip to turn off STBY-5V. When the switch is closed, this same line called Power Key now goes high and feeds
back to the Power Supply and tells the controller chip to turn STBY-5V on.
On Off
F101 To Main
3.15A/250V P201
Run 390V
STBY 159.8V Pin 1
Components
From Hot Gnd
Inside the
dashed line are
F101 (Diode Check) Hot Gnd
2 6 6
P-DIM
Local Dimming
Other
24V Audio Control Signal 10
Circuits IC1003 IC3502
Power On/Off
IC702 Mstar
Other Regs 9V Reg Dimming LVDS
Reg IC100 T-CON BOARD
(½) IC
At point
3
TV is 2 IC1002 12V 7
Q706 (½) 5V_TU Reg
in Stand-By state.
Energy Star 5V Switch LVDS 11 Video Arrives
LVDS
3.3V_ST
Relay On
compliant.
Less than 1 Watt 12V 12V
MAIN BOARD Q706
7 T-CON DC-to-DC
Converter generates
5
IC103, Q106 Inv On/Off (½) 7 3.3V 16V 26V -5V
2 8
Mstar
Resets the LVDS Panel Control
Microprocessor 7
Microprocessor
3 IC100 Power On/Off
(½) 4 4
Remote Power Button
34
42LH90 P700 on Main Board to SMPS Turn On Circuit
Q706 12V
L728 R739 47KΩ L708
12V_TCON (LVDS 12V) 6 3
R740 47KΩ Q705 Q704
5 4
0.6V 0V
L715
MAIN +5V 8 1 5V_ST
SMPS BOARD Q703
+5V_General 7 2 F6 Power On/Off
P201 P700 L709 0.2V 0.6V R726 R757 R251
n/c 1
n/c
1 n/c 10KΩ 0Ω IC100
L701 100Ω
PWR 5V
Micro
2 2 PWR ON
Gnd Gnd From IC702 3.3V_ST
3 3
From
Gnd Gnd C711
4 4 IC103,Q106 Reset D4 Reset
Gnd 5
Gnd
5
15pF Q701
Gnd Gnd
E5
6 6 RL_ON RL_ON
5.15V R706 R771 R257
7 7
5.15V 20K 0Ω 100Ω
8 8 L706
SBY5V 5.15V PANEL_CTL H5
9 9 5.2V
5.15V R245
10 10
Gnd Gnd C726 100
11 11 +5V_ST Error=5V: Normal 0V:
Gnd Gnd 220uF Micro shuts off
12 12
11.9V L704 television. Power Det H6
13 13
12V 11.9V 12V R717
14 14
Gnd Gnd 3.3KΩ
15 15 C721
Gnd Gnd
+5V_General Key 1 A4
16 16 68uF
17
24.1V
17 24V Q702 R719 10KΩ Key 2 B4
24V 24.1V
18 18 L707 C722 C728 G5 INV_CTL
n/c 19
n/c
19 47uF 1uF R7141 R713 R244 P5.3
INV.On 20
4.65V
20 INV ON/OFF 0Ω 100Ω
A.DIM 1.66V R707 R201
21 21 100 P5.6
4.7K 100Ω
ERR 0V
Error Out
Stby = 0V Run = 0V
22 22 31 Error Out
n/c 23
n/c
23 n/c
PWM-DIM 3.2V A-DIM AB13 PWM0
24 24
L700 C706 R704 R185 GPIO-09
4.7K 100Ω
PWM-DIM (PWM Dimming) Manipulates the Analog Dimming (Fixed Value) 1uF
Backlight Brightness via Customer’s OSD.
Digital Dimming (Variable)
Manipulates the Backlight Brightness via the
R760 R189
Video Processor chip. Darker Picture,
PWM-DIM AD12 PWM2
Darker Backlights to facilitate improved
L705 C725 0 100Ω
Contrast Ratio. 0.6V ~ 3.3V Range
1uF
35
Power Supply Board Low Voltage Test 1
AC Should not be applied at any time while adding resistors or while
unplugging connectors as damage to the circuit Board may occur.
(b) Unplug P700 on the Main Board to make insertion of the Resistors much
easier.
No Backlights during this test
TEST 1:
(1) Add a 100Ω resistor between (5V STBY) pin 7, 8, 9 or 10 and Pin 2
(PWR). Apply AC. This will turn on the power supply.
a) Check that the 24V and 12V power supplies are
turned on,
• P201 (24V pins 17 and 18)
• P201 (12V pins 13 and 14)
• P203 (24V pins 1 through 5) to the Inverter.
Use P700
(2) Remove AC power. Side to insert
resistors
36 February 2010 LCD DV 42LH90
Power Supply Board Backlights Test 2
P700 Connector disconnected from the Main Board. Apply AC after adding jumper.
Continue if the 1st test was OK. Leave original resistor in place.
Backlights Normal:
a) If normal, the backlights should turn on. SMPS OK, Inverter OK.
Backlights Abnormal:
a) Recheck all connections.
b) Confirm the INV On/Off line pulling up to at least 3V.
REMOVE AC POWER:
c) Check the connections to the Inverter.
If the 24V was arriving at the Inverter in Test 1 (pins 1~5 of P203) and
the Inverter On command (INV-ON pin 12 of P203) is arriving, then see
Inverter Section for further testing.
Use P700
Side to insert
resistors
37 February 2010 LCD DV 42LH90
JUAN CARLOS RODRIGUEZ L.
URUGUAY E-0679
Power Supply Connector P201 Voltage and Diode Check 4-258530
COCHABAMBA-BOLIVIA
P201 Odd "SMPS" to P601 "Main" P201 Even "SMPS" to P601 "Main"
Diode Diode
Pin Label STBY Run Pin Label STBY Run
Check Check
2
23 nc nc nc Open 24 PDIM 0V 3.2V Open
1
21 A.DIM 0.47V 1.66V Open 22 Err Out 0V 0V Open
19 nc nc nc Open 20 INV.ON 0V 4.65V Open
17 24V 0V 24.1V 0.74V 18 24V 0V 24.1V 0.74V
15 Gnd Gnd Gnd Gnd 16 Gnd Gnd Gnd Gnd
13 12V 0V 11.9V 0.98V 14 12V 0V 11.9V 0.98V
11 Gnd Gnd Gnd Gnd 12 Gnd Gnd Gnd Gnd
9 5.2V 5.15V 5.15V Open 10 5.2V 5.15V 5.15V Open
7 5.2V 5.15V 5.15V Open 8 5.2V 5.15V 5.15V Open
5 Gnd Gnd Gnd Gnd 6 Gnd Gnd Gnd Gnd
3 Gnd Gnd Gnd Gnd 4 Gnd Gnd Gnd Gnd
1 nc nc nc Open 2 PWR 0V 5.0V 1.6V
1 2
ADIM Pin 21 Fixed and not used PDIM Pin 24 can vary according to type of signal
being processed and the OSD Backlight setting.
0.33V 0% to 3.3V 100%. Output from the Video
Processor IC100.
Diode Mode values taken with all Connectors Removed
P203
1
ADIM Pin 11 Fixed and not used
2
P-DIM Pin 24 can vary according to type of signal being processed and the OSD Backlight setting.
Pin Label STBY Run Diode Check Pin Label STBY Run Diode Check
E3 L OL E4 n/a OL
120Vac 120Vac
E7 N OL E5 n/a OL
AC Voltage Readings (From Hot Ground) AC Voltage Readings for either pin 1 or pin 2 in
Pins 1 and 2 for STBY and RUN. STBY and RUN with one lead on Neutral of
SK100. (Reading from Hot Ground)
Note: With Main Power Switch Open, E5 has no
Bottom AC. E4 does have AC.
Right of With the Master Power Switch
SMPS F100 Closed (On) AC flows.
When Open (Off) AC open and does not flow.
The Inverter receives 24V from the SMPS on CN1 pins 1~5..
The Inverter On (INV ON) command from CN1 pin 12 starts
the Inverter drive signals.
P-DIM is delivered from the Main board through the SMPS to
the Inverter on CN1 pin 13.
The Inverter is responsible for delivering B+ (27.5V) to each of
the 64 LED Blocks. This is accomplished by 4 DC to DC
Converters (M1~M4) on the board, (easily identified by the 4
yellow capacitors on the lower left of the board.
• M1 and M3 are routed out CN4
• M2 and M4 are routed out CN3.
M1-M3
ON/OFF 120Hz Backlight Quad 12 Bit Drive
(Inverter On/Off) Blanking Signal LVDS Video Signal 27.6V
24V 24V P203 SMPS
INV-ON CN1 P3501 LVDS
Error
12V
12V
STBY 5V,
VBR-B 24V
12V, 24V 12V
PWM-DIM STBY 5V Switch 8 LEDs
PWR (Power On)
(Global Dimming) Q706 Per/block
Inv On/Off
There are two PWM-DIM IC3502
Panel CTL
DC Voltage Dimming
DC to DC PWR 12V JUAN CARLOS RODRIGUEZ L.
Manipulated by: P201 Tur-Motion
converters URUGUAY E-0679
Video Content
(27.6V) for
Error
P700 4-258530
Intelligent Sensor
each plug
Customer’s Menu
ON/OFF COCHABAMBA-
IC801 BOLIVIA
Relay On
CN3/CN4 (Inverter On/Off)
Called M1-M4 Backlight Setting XD Engine
PWM-DIM
(Global Dimming) Luminance
Backlight Selection
Only affects P-DIM Video
Backlight setting I100
determines the Mstar
Backlight brightness Chip
Ceiling Customer’s Menu
Brightness Selection Intelligent Sensor
Only affects MAIN BOARD
(Room Light Monitor)
Luminance information Only affects P-DIM
42
Inverter Connector Identification
CN305 n/c
CN306
CN307 n/c
CN3 CN4
Chocolate CN1
M1
27.5V
M2
Power
Supplies
M3
M4
Connected to
CN3 or CN4
Also, all blocks are manipulated simultaneously via (Global Dimming) by IC100 Video Processor.
The Overall intensity of the backlights is manipulated by the “Global Dimming” signal from the
Mstar (IC100) chip called Digital-Dimming (PWM-DIM).
The areas in the picture on the left shown by A, B, C and D show the dark areas of the screen.
The picture on the right shows the backlight LEDs. Note they are dimmed out in the same area
as the dark video on the left.
To see a representation of the “Local Dimming” the TV has to be set to the “Store Mode”.
Note: These graphics are from the 47LG90 which has more LEDs than the 42LH90,
but the explanation remains the same.
M2
27.5V
TP
M3
M4
Each of the 4 capacitors C12, C27, C212 and
C227 have a TP just above the (+) leg of the cap.
Q35 - Q50
Are LED Block
Drivers for CN3
F1
Center of the Board 2A/125V
Left of CN1 Connector
JUAN CARLOS R.
CBBA-BO
F2
12A/65V
Crystal Y301
23.9V
26.4V Gnd
28.0V Gnd
GND
3.29V
6.99V
IC2 IC15
1.0V 7V
1.71V
6.95V
GND
7.0V GND
IC303
IC302
GND 7.0V
1.8V
12V is supplied to the T-Con Board on connector CN1 from the Main Board
(easily measured at fuse F1).
There is one regulator that creates 1.8V developed at pin 2 (Center Leg) of U11.
These voltages can be read at the ribbon connector or at test points on the
board which will be identified later.
CN5 CN4
FL2
JUAN CARLOS
RODRIGUEZ
D9
U12
D7
FL1 UC1 D10
U11 U5
Q1
D8
F1
U10
CN1 CN2
CN5
T-CON
CN4
(TFT Driver)
FL2
P/N EAT60665101 VCC Gnd Protect
3.3V L2 Gnd D9 -4.9V
U12
3.3V 27V
-2.4V D10
D7 20.5V
14.25V
1 UC1
2 2 U5 B+ ( 12V )
R704
R705
R706
3 U5
U11 C
FL1 26V 16V
Gnd Protect 3.3V L1
1) 0V R702 R701
U10 2) 1.19V Q1
3) 3.3V B E 16V
C744
R721
1) Gnd 8) 3.34V 2.78V 3.3V VDD
2) Gnd 7) 3.09V F1 (12V) ( 12V ) D8
3) Gnd 6) 3.34V 125V / 3A
4) Gnd 5) 3.34V 16V
CN1 CN2
62
T-CON (TFT Drive) Board Checks
T-CON Board
0V
1.8V F1
3.3V
CN1
Check the Regulator U11 for
Correct Voltage
F1 (Diode Mode Check)
Open (Red Lead on Fuse)
0.46V (Black Lead on Fuse)
3.3V TP -5V
VCC Source
D7 D9 Anode
12V
Pin 25,26
Chip B+
26V
D7
3.3V Source U5 Source
Cathode Pin 8
3.3V Pin 23, 24
12V
Pin 37,38
Chip B+
16V (VDD)
Pin 42
16V (D6)
Not for Panel Cathode
T-CON Board 16.9V
64 February 2010 LCD DV 42LH90
T-CON (TFT Driver) Board CN4 and CN5 (Voltage Check)
3.3V 3.3V
Pin 7,8 Pin 53,54
CN5 CN4
26V 26V
Pin 57 Pin 4
CN5 CN4
JUAN CARLOS RODRIGUEZ L.
URUGUAY E-0679
4-258530
COCHABAMBA-BOLIVIA
T-CON Board
LVDS
• LVDS 12V (Not generated, but switched
AUDIO
from the 12V arriving from the SMPS.
• 3.3V
• 1.8V
TUNER and VSB CIRCUIT
• 9V which is used to make 5V TU Mstar IC100 Video and Micro Processors
• 5V TU • 1.2V
• 3.3V IC3502 Tru-Motion and Dimming IC.
• 1.2V • 1.26V_MEMC, 1.8V_MEMC,
1.8V_DDR, and 3.3V
IC3502 SW3500
Dimming Not VIDEO
P3501 Tru-Motion used PROCESSOR
to Inverter IC100 and
Tru-Motion IC3502
X3500 runs Hot.
DDR
This is normal.
P700 IC100
to SMPS Micro/Video n/c
DDR
Processor
X800 IC801
SW100
Reset
P1200 USB
to IR Board
P600 HDMI
to Speakers Selector
X100
IC600
Audio
Tuner
TU1001
Rear Inputs
IC3502 Operates at
high temperature
X3500
Q706 IC704 25Mhz
L726
P700
E B
IC901
C IC705 IC2
L710
Q702 IC801
L718 X800
IC706 12Mhz XD
Q701 IC701 Engine P101
E B IC105
IC900 N/A
C
IC1
IC708 IC707
IC101
E L712
C B
Q100
SW100
IC100 IC1000
P1200 Micro/Video IC1001
X100
E 12Mhz Processor D1000
C B Mstar
P600 L607 Q106 X1005
25Mhz
IC1004
IC600 IC502
IC1002 L606
IC1203
Analog Video (19)
SIF (16)
TU1001 Tuner Dig DIF- (13)
TDVW-H103F Dig DIF+ (12)
Clock (9)
Data (8)
(1)
70
42LH90 Main (Front Side) Component Voltages
IC101 Serial Flash IC705 +1.26V_VDDC IC1000 +1.26V_PVSB IC3503 +1.8V Reg Q706 +5V/12VLVDS
Pin Memory Pin Regulator Pin Regulator Pin Dimming Pin Switch
[1] 0.05V [1] 0.8V [1] 0V [1] 0.58 [1] 5.1V
[2] 3.2V [2] Gnd [2] 3.39V [2] 1.8V [2] 0.29V
[3] 2.5V [3] 5V [3] 3.4V [3] 3.19V [3] 11.9V
[4] Gnd [4] 6V [4] 0V [4] 5.99V
[5] 0V [5] 3.2V [5] 0V IC3204 Dimming [5] 11.98V
[6] 0V [6] 1.2V [6] 1.21V Pin EEPROM [6] 11.98V
[7] 3.3V [7] 1.26V [7] 0.8V [1] Gnd [7] 5.06V
[8] 3.3V [8] 5V [8] Gnd [2] Gnd [8] 5.06V
[3] Gnd
IC105 HDCP IC706 5V_EXT IC1001 +3.3V_PVSB [4] Gnd Q1200 IR RS232
Pin EEPROM Pin Memory Pin +3.3V_FE [5] 3.3V Pin Buffer
[1] Gnd [1] 0.8V [1] 4.94V [6] 3.3V B 0.634V
[2] Gnd [2] Gnd [2] 4.94V [7] 0V C 0.97V
[3] 3.29V [3] 12V [3] Gnd [8] 3.3V E Gnd
[4] Gnd [4] 9.6V [4] 3.4V
[5] 3.3V [5] 5V [5] 1.25V Q100 W/P IC101 D1000 Speed Up Reset
[6] 3.3V [6] 4.97V Pin Pin IC1004
[7] 0V [7] 4.97V IC1002 +5V_TU B 0V C 3.4V
[8] 3.3V [8] 1.9V Pin Tuner C 2.5V A 3.38V
[1] 8.92V E Gnd
IC701 +1.8V_DDR IC707 +1.8V_MEMC [2] 1.88V
Pin Regulator Pin Regulator [3] 5.04V Q106 S5/S6 Reset
[1] 0V [1] 0.8V [4] 0V Pin Mstar
[2] 3.2V [2] Gnd [5] Gnd B 0V
[3] 3.2V [3] 4.92V C 3.28V
[4] n/c [4] 6.5V IC1203 SPIF Optical E 0V
[5] n/c [5] 4.8V Pin Audio
[6] 1.8V [6] 1.8V [1] 1.58V Q702 INV_ON
[7] 0.8V [7] 1.8V [2] 3.2V Pin Inverter
[8] Gnd [8] 4.8V [3] Gnd B 0.05V
[4] 1.61V C 4.66V
IC704 +3.3V_FE IC708 +1.26V_MEMC [5] 3.21V E Gnd
Pin Regulator Pin Regulator
[1] 0.8V [1] Gnd IC3500 +3.3V_Dimming
[2] Gnd [2] 0.8V Pin Regulator
[3] 5V [3] 1.26V [1] Gnd
[4] 7.5V [4] 1.26V [2] 3.3V
[5] 5V [5] 1.8V [3] 5V
[6] 3.3V [6] 5V
[7] 3.3V [7] 1.26V
[8] 2.1V [8] 5V
71
42LH90
Main Board
(Back Side)
42LH90 MAIN BOARD
Component Layout (Back View)
IC3505
Q705 B
E C
Q704 B
E C
IC800 Q703 B C IC107
E
2 1
3
IC102
FLASH
IC1202 IC104
IC702
Q105
E
C B
D500 2
1
IC103
A2 A1 Q1000 D102 3
Q1001 E
C E A1 B C
B IC1201
C B C A2 C E Q600
IC501
A2 C
13 DIF -
12 DIF + D1223
(5V) 4
72
42LH90 Main (Back Side) Component Voltages
IC103 Reset Gen IC1003 9V Reg IC3505 Reset Gen Q1001 Tuner Video
Pin Mstar IC100 Pin to IC1002 Pin for IC3502 Pin Buffer
[1] Gnd [1] 12V [1] 3.3V B 3.09V
[2] 0V [2] Gnd [2] Gnd C 0V
[3] 3.3V [3] 8.9V [3] 3.22V E 3.72V
For Tuner Voltage 5V
IC104 RGB (PC) Q105 PWR On Delay D102 Audio Mute
Pin EEPROM IC1200 RGB Pin Q2405 Pin Routing
[1] Gnd Pin EEPROM B 0V A1 0.047V
[2] Gnd [1] Gnd C 1.95V C 0.089V
[3] Gnd [2] Gnd E Gnd A2 0V
[4] Gnd [3] Gnd
[5] 3.22V [4] Gnd Q600 Audio Mute D500 Shunt for
[6] 3.22V [5] 4.82V Pin Switch Pin IC501
[7] 0V [6] 4.82V B 0.08V A1 3.25V
[8] 3.22V [7] 4.82V C 3.26V C 3.12V
[8] 4.82V E Gnd A2 0V
IC107 Power Det
Pin Gen IC1201 RS232 Q703 5V Switch D1223 5V Routing
[1] Gnd Pin Rx/Tx Pin Control Pin for IC1200
[2] 3.9V [1] 3.3V B 0.6V A1 0V
[3] 3.28V [2] 5.56V C 0.03V C 4.82V
[3] 0.02V E Gnd A2 5.11V
IC702 +3.3V_ST [4] 0.03V
+3.3V_AVDD_MPLL [5] 5.46V Q704 12V LVDS
3 Pin Regulator [6] 5.5V Pin Switch Control
[1] Gnd [7] 5.5V B 0.05V
[2] 3.29V [8] 0V C 0.65V
1 3 2 [3] 5.11V [9] 3.29V E Gnd
[10] 3.24V
IC703 +3.3V_ST [11] 0.02V Q705 12V LVDS
Pin Regulator [12] 3.29V Pin Switch
[1] 0V [13] 0V B 0.65V
[2] 1.8V [14] 5.5V C 0.0V
[3] 3.21V [15] Gnd E Gnd
[16] 3.29V
Q1000 Tuner SIF
IC800 SPI Flash IC1202 USB +5V Pin Buffer
Pin Pin Switch B 2.4V
[1] 0.12V [1] 4.95V C 0V
[2] 1.13V [2] Gnd E 3.85V
[3] 3.26V [3] 3.21V
[4] Gnd [4] 4.95V
[5] 0.06V [5] 0V
[6] 1.2V [6] 4.95V
[7] 3.27V
[8] 3.27V
73
Main Board X100 and X800 Crystal Checks
X100
2.56Vp/p 12Mhz
Set on or off. Use bottom leg.
1.51V
1.59V
IC800 XD Engine Crystal
2.25Vp/p 12Mhz
Set on. Use bottom leg.
3.94Vp/p 25Mhz
Set on. Use Left leg.
3.54Vp/p 25Mhz
Set on. Use Top leg.
5.67Vp/p
25Mhz
MAIN Board 1.64V Bottom
Leg
Main Board
LD1000 Location
LD1000
76 February 2010 LCD DV 42LH90
Main Board Connector P700 to Power Supply Voltage and Diode Check
P700 “Main Board" to P201 “SMPS"
Odd Pins Even Pins
Diode Diode
Pin Label STBY Run Pin Label STBY Run
Check Check
2
23 nc nc nc Open 24 PDIM 0V 2.43V 1.3V
P700
1
21 A.DIM 0.47V 1.66V Open 22 Err Out 0V 0V Open
19 nc nc nc Open 20 Inv_On 0V 4.65V 2.9V
17 24V 0V 24V Open 18 24V 0V 24V Open
15 Gnd Gnd Gnd Gnd 16 Gnd Gnd Gnd Gnd
13 12V 0V 12V 2.2V 14 12V 0V 12V 2.2V
11 Gnd Gnd Gnd Gnd 12 Gnd Gnd Gnd Gnd
9 5.2V 5.15V 5.15V 1.1V 10 5.2V 5.15V 5.15V 1.1V
7 5.2V 5.15V 5.15V 1.1V 8 5.2V 5.15V 5.15V 1.1V
5 Gnd Gnd Gnd Gnd 6 Gnd Gnd Gnd Gnd
3 Gnd Gnd Gnd Gnd 4 Gnd Gnd Gnd Gnd
1 nc nc nc Open 2 PWR-ON 0V 5V 2.6V
1 2
ADIM Pin 21 Fixed and not used. PDIM Pin 24 can vary according to type of signal
It is an Open connection on the Inverter Board. being processed, OSD Backlight setting. 0.6V 0%
to 3.3V 100% and the Intelligent Sensor. Output
from the Video Processor IC100.
Diode Mode values taken with all Connectors Removed
1 LVDS 12V 12V Open 21 LVDS_CH2_B+ 1.1V 0.87V 41 Gnd Gnd Gnd
2 LVDS 12V 12V Open 22 LVDS_CH2_B- 1.4V 1.2V 42 OPC-EN n/c 1.09V
23 LVDS_CH2_A+ 1.1V 1.22V 43 OPC-Out n/c Open
3 LVDS 12V 12V Open
24 LVDS_CH2_A- 1.4V 0.88V 44 *PWM-DIM n/c Open
4 LVDS 12V 12V Open
25 n/c n/c n/c 45 LVDS-Sel n/c Open
5 n/c n/c n/c
26 Gnd Gnd Gnd 46 n/c n/c Open
6 Gnd Gnd Gnd
27 LVDS_CH1_E+ 1.1V 0.87V 47 n/c n/c Open
7 Gnd Gnd Gnd
28 LVDS_CH1_E- 1.4V 1.23V 48 n/c n/c Open
8 Gnd Gnd Gnd
29 LVDS_CH1_D+ 1.1V 1.23V 49 n/c n/c Open
9 Gnd Gnd Gnd
30 LVDS_CH1_D- 1.4V 1.23V 50 n/c n/c Open
10 Gnd Gnd Gnd
31 Gnd Gnd Gnd 51 Gnd Gnd Gnd
11 LVDS_CH2_E+ 1.09V 1.23V
32 LVDS_CH1_CLK+ 1.26V 1.20V
12 LVDS_CH2_E- 1.44V 0.875V
33 LVDS_CH1_CLK- 1.25V 1.2V PWM-DIM (Pin 44) is Open on
13 LVDS_CH2_D+ 1.09V 1.23V the Main Board.
34 Gnd Gnd Gnd
14 LVDS_CH2_D- 1.44V 1.23V
35 LVDS_CH1_C+ 1.4V 0.88V
15 Gnd Gnd Gnd
36 LVDS_CH1_C- 1.4V 1.22V
16 LVDS_CH2_CLK+ 1.22V 1.14V
37 LVDS_CH1_B+ 1.2V 1.11V 1
17 LVDS_CH2_CLK- 1.21V 1.25V
38 LVDS_CH1_B- 1.3V 1.23V
18 Gnd Gnd Gnd
19 LVDS_CH2_C+ 1.13V 1.23V
39 LVDS_CH1_A+ 1.2V 1.18V P3500
40 LVDS_CH1_A- 1.3V 1.05V
20 LVDS_CH2_C- 1.4V 0.87V
Pin Label Run Diode Test Pin Label Run Diode Test P3502 1
1 Gnd Gnd Gnd 21 LVDS_CH3_D+ 1.2V 1.2V
2 Gnd Gnd Gnd 22 LVDS_CH3_D- 1.3V 1.23V
3 LVDS_CH4_E+ 1.15V 1.18V 23 Gnd Gnd Gnd
4 LVDS_CH4_E- 1.4V 1.24V 24 LVDS_CH3_CLK+ 1.3V 0.87V
5 LVDS_CH4_D+ 1.25V 0.87V 25 LVDS_CH3_CLK- 1.23V 0.87V
6 LVDS_CH4_D- 1.3V 1.12V 26 Gnd Gnd Gnd
7 Gnd Gnd Gnd 27 LVDS_CH3_C+ 1.2V 1.03V
8 LVDS_CH4_CLK+ 1.29V 1.22V 28 LVDS_CH3_C- 1.3V 0.87V
9 LVDS_CH4_CLK- 1.3V 1.23V 29 LVDS_CH3_B+ 1.2V 0.87V
10 Gnd Gnd Gnd 30 LVDS_CH3_B- 1.3V 1.23V
11 LVDS_CH4_C+ 1.2V 0.87V 31 LVDS_CH3_A+ 1.2V 1.20V
12 LVDS_CH4_C- 1.3V 0.87V 32 LVDS_CH3_A- 1.28V 0.87V
13 LVDS_CH4_B+ 1.3V 1.23V 33 Gnd Gnd Gnd
14 LVDS_CH4_B- 1.29V 0.87V 34 n/c n/c n/c
15 LVDS_CH4_A+ 1.25V 1.23V 35 n/c n/c n/c
16 LVDS_CH4_A- 1.29V 0.87V 36 n/c n/c n/c
17 Gnd Gnd Gnd 37 n/c n/c n/c
18 Gnd Gnd Gnd 38 n/c n/c n/c
19 LVDS_CH3_E+ 1.18V 1.08V 39 n/c n/c n/c
20 LVDS_CH3_E- 1.13V 1.07V 40 n/c n/c n/c
41 Gnd Gnd Gnd
Audio B+
24V
P600 Pins 49-52
IC600 Mute
Driver
Q600
Back of
board
Mute
Pin 25
Use speaker out to test for defective Audio Amp IC600
Note: (Normal, ½ Audio B+)
P400 CONNECTOR "Main" to "Speakers"
Pin LABEL SBY Run Diode Check
1 SPK-R(-) 0V 12V 2.63V
2 SPK-R(+) 0V 12V 2.63V
3 SPK-L(-) 0V 12V 2.63V
4 SPK-L(+) 0V 12V 2.63V
The Intelligent Sensor and IR board (located on the bottom left as viewed from the rear) contains the
IR (Infrared Remote Sensor) and the Intelligent Sensor. This board also connects with the Side Key
Board and the Moving LED board which contains the 10 front Power LEDs.
The IR board receives it operating B+ via P101 pin 6 (STBY 5V) and pin 11 (3.3V) from connector
P1200 on the Main board.
The Intelligent Sensor communicates with the Micro/Video Processor IC100 Mstar Chip via clock and
data lines SCL1 and SDA1 (AA17 and AA18) arriving on connector P101 from P700 pins 1 and 2 on
the Main board.
The Front Power LEDs are controlled by these same Clock and Data lines which communicate with
the LED Driver IC U1 on the Moving LED board.
The IR pulses (5V p/p) P101 pin 9 are sent to P1200 on the Main board and on to the Microprocessor
(IC100) via pin C4.
The Key board is routed to the IR board via P100 to P102 on the Key 1 and Key 2 lines, (Key 1 pin 1
and Key 2 pin 3). Then out P101 pins 4 and 5 to P1200 on the Main Board.
Then to the Microprocessor A4 and B4 lines.
p/n EBR62127501
Key board
p/n EBR62128101
P101
P100
J1
P102
P100
Power LEDs
J1 Connector
To Intelligent
Pin 1 Sensor and IR
Board
U1
LED Driver
84 February 2010 LCD DV 42LH90
Front Board Connectors P101 and P2 Voltage and Diode Check
P101 CONNECTOR "Front IR / Intelligent Sensor" to P1200 " MAIN Board "
Diode
Pin Label STBY Run
Check
1 SCL 0.57V 3.2V Open P2 Connector to “Side Key" P100
2 SDA 0.57V 3.2V Open Diode
Pin Label STBY Run
3 Gnd Gnd Gnd Gnd Check
1 Key 1 3.2V 32V Open
4 Key1 3.2V 3.2V Open
2 Gnd Gnd Gnd Gnd
5 Key2 3.2V 3.2V Open
3 Key 2 3.2V 3.2V Open
6 ST_5V 5.1V 5.1V Open
4 Gnd Gnd Gnd Gnd
7 Gnd Gnd Gnd Gnd
8 Warm_ST Gnd Gnd Open
9 IR 3.5V 3.5V Open
10 Gnd Gnd Gnd Gnd
11 3.3V 3.2V 3.2V Open
12 LED On 0V 3.2V Open
Diode Diode
Pin STBY Run Pin
Check Check
1 5V 5V Open 1 Open
2 Gnd Gnd Gnd 2 Gnd
See P100
3 0.59V 4.9V Open 3 Open
Table for Voltages
4 Gnd Gnd Gnd 4 Gnd
5 0.75V 5V Open 5 Open
6 Gnd Gnd Gnd 6 Gnd
7 *0V *3.27V Open 7 Open
8 0V 0V Open 8 Open
SW101
SW103
SW105
SW107
SW100
SW102
SW104
SW106
Elimination of the
conventional
speaker.
Speaker
Attachment
post
Invisible Speaker Tweeter
shown separately. The Front (down)
has an adhesive surface which
Cabinet works as Outlined adheres to front bezel. Note, there is
a diaphragm. Circle no diaphragm, only voice coil.
Dust Cap
with
Magnet
adhesive
Voice Coil
Inside
Frequency Pass
Capacitor
Mount
This section shows the 11X17 foldout that’s available in the Paper
and Adobe version of the Training Manual.
23 nc nc nc nc 2 2.6V
CN5 T-CON P/N EAT60665101 CN4 3,4,5,6 Gnd
P203 "SMPS" TO 22 Err Out 0V 0V Open
INVERTER CN3-CN4 INFO. (TFT Driver) FL2
1.1V
CN1 "INVERTER" VCC Gnd Protect
21 1 A.DIM 0V 1.66V Open 7,8,9,10
IC303
CN3 CN4 3.3V L2 Gnd -4.9V
2 3 21 27.5V Line on CN3 27.5V Line on CN4 Diode U12 D9
20 INV.ON 0V 4.65V Open 11,12 Gnd
Y301 (12Mhz)
Pin Label Check
12 3 2 Pins 1-2 (Out_M2) Pins 1-2 (Out_M3) 3.3V 27V
19 nc nc nc nc 13,14 2.2V
1.76Vp/p 1.25Vp/p
14 AGP OPEN -2.4V D10
IC302 Pins 13-14 (Out_M2) Pins 13-14 (Out_M3) 20.
14.25
13
D7 5V 17,18 24V 0V 24V 0.74V 15,16 Gnd
IC301
Pins 16-17 (Out_M2) Pins 16-17 (Out_M3) Ext_VBR_B OPEN V
D302 Processor 1) 0V 1 UC1 17,18
CN305 Pins 26-29 (Out_M2) Pins 26-29 (Out_M3) 12 ON/OFF OPEN Gnd Protect 2) 1.19V 2 2 15,16 Gnd Gnd Gnd Gnd Open
R704
R705
R706
3 U5 B+ ( 12V ) U5
D302 blinks Q19 Pins 31-32 (Out_M4) Pins 31-32 (Out_M1) 3) 3.3V
Open
Q50 n/c 11 NC OPEN U11 C 13,14 12V 0V 12V 0.98V 19
1Hz OK Q20 Pins 43-44 (Out_M4) Pins 43-44 (Out_M1) FL1 3.3V 26V 16V
L1
Q49 IC5
Pins 46-47 (Out_M4) Pins 46-47 (Out_M1) 10 GND GND Q1 R702 R701 11,12 Gnd Gnd Gnd Gnd 20 2.9V
Q21 1) Gnd U10 8) 3.34V
Q48
IC14
CN306 Pins 58-59 (Out_M4) Pins 58-59 (Out_M1) 9 GND GND 2) Gnd 7) 3.09V B 16V 7,8,9,10 5V 5.15V 5.15V Open 21 Open
Q22 E
C744
R721
Q47
3) Gnd 6) 3.34V 2.78V
ZD304 8 GND GND 125V / F1 (12V)
3.3V
( 12V ) D8
VDD
22 Open
ZD303
(Pin 6)
4) Gnd 5) 3.34V 3,4,5,6 Gnd Gnd Gnd Gnd
Q46 Q23
7 GND GND 3A 16V
IC13 Q24 3.46Vp/p
2 PWR-On 0V 4.98V 1.6V 23 Open
Q45
IC6 6 GND GND CN1 CN2
Q44 Q25
n/c (Pin 4)
1 nc nc nc nc 24 1.3V
CN307
3.48Vp/p 1-5 VIN 0.74V
Q43 Q26 12V LVDS Pins 48~51 For Voltages see P201
(Pin 1)
For Voltages see CN1 Table 2
1 PDIM Pin 24 can vary according to type of signal
3.54Vp/p ADIM Pin 21
Q42 Q27 being processed and the OSD Backlight setting.
12V LVDS Pins 1~4 Fixed and not
Q41 IC10 IC7 Q28 0.6V 0% to 3.3V 100%.
used
Q40 Q29
P1200 "MAIN” to P101 "Front IR / LED Output from the IC100 Video Processor.
Q39 Q30
SMPS TEST 1: To Force
Pin Label STBY Run Diode Check P203 SMPS Power Supply On.
P3500 P3502
Q38 Q31
1 SCL 0.57V 3.3V Open Switch Mode Power Supply Disconnect P700 on Main
Q37 IC9 IC8
Q32 D215 PWB. 12V LVDS 42LH90
2 SDA 0.57V 3.3V Open Pins 1~4 MAIN BOARD
Q36 Q33
T101 P201 Jump pin 7,8,9 or 10 (5V) to
Q35 Q34 3 Gnd Gnd Gnd Gnd pin 2 using a 100Ω resistor. IC3504 IC3502 IC3502
4 Key1 3.2V 3.2V Open D213 (Test Voltage Outputs 12V, Operates at Tru- SW3500
INVERTER Board and 24V). P3501 IC3503
high Motion/ Not Used
To Backlights
P1200 B
FLASH
Hot Q100
Q12 Q11 D7 11 NC 0.47V 1.66V OPEN SW100 IC104
L3 C3 Q602 Gnd IC702 IC100 IC1000
C27 M3+ 10 GND GND GND GND IC1001 IC1202
680uF Micro/Video IC102
E Q106 Processor D1000
35V D8 C B
9 GND GND GND GND
Bridge Rectifier
L601 D1000
Side (Key) Controls
- Q105 E Mstar
L4 F100 SK100 B X1005
Q202
Q203
IN
250V Q1000 A1 A2
AC
Q205 Q204 D203 IC600 Q600
7 GND GND GND GND E C
680uF
L201
SK101 B A1 C
35V
E C IC1004
N
C212 M2+ C E C A2
IC502
IC1201 B
B
6 GND GND GND GND
L
680uF IC501
D102 Q1001
35V D202 C203
1-5 IC1002
- L202 VIN 0V 24.0V 2.9V L606 IC703 IC1203 Analog Video
Q210
Q209
1 IC1200 (19)
Ext_VBR_B same as (P-DIM) C A1
Q212 Q211 D207 P102 "Front IR / LED PWB to P100 Keys D1223 SIF (16)
C227 + M1 L203 P101 Main Power SW Tuner A2 Dig DIF- (13)
680uF
IC201
Diode IC1003 Dig DIF+ (12)
Pin Label STBY Run TU1001 Tuner
35V
- D208 Front PWB Check TDVW-H103F Clock (9)
L204 1 Key1 3.2V 3.2V Open Data (8)
P100
P102
Assembly
Q19 through Q50 2 Gnd Gnd Gnd Gnd Q1200 Tuner 5V_TU
Note: Each output driver (switch) has a TP to the left and right IR Receiver B C (4)
3 Key2 3.2V 3.2V Open
representing a “V” which indicates a Block of LEDs. Intelligent Sensor P100 E
V34 represents Pin 23 of CN4 4 Gnd Gnd Gnd Gnd (1)
V33 represents Pin 24 of CN4
Grounding these points when the 27.6V supplies are working will
cause the entire Block of Backlight LEDs to turn on.
(100mA to light one block) J1 LED Board
Speakers
42LH90 MAIN (FRONT SIDE) SIMICONDUCTORS
IC101 Serial Flash IC704 +3.3V_FE IC707 +1.8V_MEMC IC1001 +3.3V_PVSB IC3500 +3.3V_Dimming Q100 W/P IC101 Q706 +5V/12VLVDS
Pin Memory Pin Regulator Pin Regulator Pin +3.3V_FE Pin Regulator Pin Pin Switch
[1] 0.05V [1] 0.8V [1] 0.8V [1] 4.94V [1] Gnd B 0V [1] 5.1V
[2] 3.2V [2] Gnd [2] Gnd [2] 4.94V [2] 3.3V C 2.5V [2] 0.29V
[3] 2.5V [3] 5V [3] 4.92V [3] Gnd [3] 5V E Gnd [3] 11.9V
[4] Gnd [4] 7.5V [4] 6.5V [4] 3.4V [4] 5.99V
[5] 0V [5] 5V [5] 4.8V [5] 1.25V IC3503 +1.8V Reg Q106 S5/S6 Reset [5] 11.98V
[6] 0V [6] 3.3V [6] 1.8V Pin Dimming Pin Mstar [6] 11.98V
[7] 3.3V [7] 3.3V [7] 1.8V IC1002 +5V_TU [1] 0.58 B 0V [7] 5.06V
[8] 3.3V [8] 2.1V [8] 4.8V Pin Tuner [2] 1.8V C 3.28V [8] 5.06V
[1] 8.92V [3] 3.19V E 0V
IC105 HDCP IC705 +1.26V_VDDC IC708 +1.26V_MEMC [2] 1.88V Q1200 IR RS232
Pin EEPROM Pin Regulator Pin Regulator [3] 5.04V IC3504 Dimming Q702 INV_ON Pin Buffer
[1] Gnd [1] 0.8V [1] Gnd [4] 0V Pin EEPROM Pin Inverter B 0.634V
[2] Gnd [2] Gnd [2] 0.8V [5] Gnd [1] Gnd B 0.05V C 0.97V
[3] 3.29V [3] 5V [3] 1.26V [2] Gnd C 4.66V E Gnd
[4] Gnd [4] 6V [4] 1.26V IC1203 SPIF Optical [3] Gnd E Gnd
[5] 3.3V [5] 3.2V [5] 1.8V Pin Audio [4] Gnd D1000 Speed Up Reset
[6] 3.3V [6] 1.2V [6] 5V [1] 1.58V [5] 3.3V Pin IC1004
[7] 0V [7] 1.26V [7] 1.26V [2] 3.2V [6] 3.3V C 3.4V
[8] 3.3V [8] 5V [8] 5V [3] Gnd [7] 0V A 3.38V
[4] 1.61V [8] 3.3V
IC701 +1.8V_DDR IC706 5V_EXT IC1000 +1.26V_PVSB [5] 3.21V
Pin Regulator Pin Memory Pin Regulator
[1] 0V [1] 0.8V [1] 0V
[2] 3.2V [2] Gnd [2] 3.39V
[3] 3.2V [3] 12V [3] 3.4V
[4] n/c [4] 9.6V [4] 0V
[5] n/c [5] 5V [5] 0V
[6] 1.8V [6] 4.97V [6] 1.21V
[7] 0.8V [7] 4.97V [7] 0.8V
[8] Gnd [8] 1.9V [8] Gnd
IC103 Reset Gen IC703 +3.3V_ST IC1200 RGB IC1202 USB +5V Q703 5V Switch Q1001 Tuner Video
Pin Mstar IC100 Pin Regulator Pin EEPROM Pin Switch Pin Control Pin Buffer
[1] Gnd [1] 0V [1] Gnd [1] 4.95V B 0.6V B 3.09V
[2] 0V [2] 1.8V [2] Gnd [2] Gnd C 0.03V C 0V
[3] 3.3V [3] 3.21V [3] Gnd [3] 3.21V E Gnd E 3.72V
[4] Gnd [4] 4.95V
IC104 RGB (PC) [5] 4.82V [5] 0V Q704 1st 12V LVDS D102 Audio Mute
Pin EEPROM IC800 SPI Flash [6] 4.82V [6] 4.95V Pin Switch Control Pin Routing
[1] Gnd Pin [7] 4.82V B 0.05V A1 0.047V
[2] Gnd [1] 0.12V [8] 4.82V IC3505 Reset Gen C 0.65V C 0.089V
[3] Gnd [2] 1.13V Pin for IC3502 E Gnd A2 0V
[4] Gnd [3] 3.26V IC1201 RS232 [1] 3.3V
[5] 3.22V [4] Gnd Pin Rx/Tx [2] Gnd Q705 2nd 12V LVDS D500 Shunt for
[6] 3.22V [5] 0.06V [1] 3.3V [3] 3.22V Pin Switch Control Pin IC501
[7] 0V [6] 1.2V [2] 5.56V B 0.65V A1 3.25V
[8] 3.22V [7] 3.27V [3] 0.02V Q105 PWR On Delay C 0.0V C 3.12V
[8] 3.27V [4] 0.03V Pin Q2405 E Gnd A2 0V
IC107 Power Det [5] 5.46V B 0V
Pin Gen IC1003 9V Reg [6] 5.5V C 1.95V Q1000 Tuner SIF D1223 5V Routing
[1] Gnd Pin to IC1002 [7] 5.5V E Gnd Pin Buffer Pin for IC1200
[2] 3.9V [1] 12V [8] 0V B 2.4V A1 0V
[3] 3.28V [2] Gnd [9] 3.29V Q600 Audio Mute C 0V C 4.82V
[3] 8.9V [10] 3.24V Pin Switch E 3.85V A2 5.11V
IC702 +3.3V_ST For Tuner Voltage 5V [11] 0.02V B 0.08V
+3.3V_AVDD_MPLL [12] 3.29V C 3.26V
Pin Regulator [13] 0V E Gnd
[1] Gnd [14] 5.5V
[2] 3.29V [15] Gnd
[3] 5.11V [16] 3.29V
42LH90 LVDS P3500 WAVEFORMS