Sei sulla pagina 1di 2

Index

SUPERFIXALL Technical Data Sheet

DESCRIPTION
Superfixall is a rigid set, exceptionally high strength, high
quality waterproof cement-based adhesive developed
to bond most types of ceramic tiles for wall and floor
applications. Ideal for bonding monocottura and fully
vitrified tiles, as well as natural stone, marble, granite and
mosaic tiles onto brickwork, cement render and concrete
walls and floors. Suitable for both internal and external,
thick and thin bed applications.

FEATURES & BENEFITS


✓ High strength bond
✓ No odour
✓ Economical
✓ Water cleanable adhesive is now ready to use. ASA Megalastic should be used
✓ Easy to spread as a total water replacement to fortify adhesive and increase
✓ Thick and thin bed applications adhesion, flexural and compressive strength.

RECOMMENDED FOR APPLICATION


✓ Concrete All workmanship must be carried out in accordance with
✓ Cement render AS3958.1- 2007. Apply the mixed adhesive to the prepared
✓ Brickwork substrate using the appropriate notched trowel for the size
✓ Blockwork of the tile being laid. A minimum of 1mm bed thickness for
✓ Swimming pools walls and a minimum of 3mm for floors must be achieved.
✓ Use in areas covered by AS3958.1 - 2007 Ensure that the tiles are fully supported by the adhesive
with no voids. Do not spread more than 1m2 of Superfixall
SURFACE PREPARATION at a time. Lay tiles into the adhesive before it skins. Do not
All surfaces must be clean, dry, free from dust, grease, wax, disturb tiles until the adhesive has set. Recommended for
oil, laitance, curing compounds, paint, friable material tiling over ASA/Bostik approved waterproofing membranes
and all other contaminants likely to prevent the adhesive only when mixed with undiluted ASA Megalastic.
bonding. Highly porous substrates should be primed with
ASA Multiprime prior to tiling. Non absorbent/impervious DRYING
substrates must not be primed. Cement render/screeds Allow a minimum of 24 hours for the adhesive to set (or when
must be allowed to dry for 7 days, concrete to be left with a tile work is firm) prior to allowing foot traffic or grouting.
wood float finish and allowed to cure for at least 28 days. Do not tile if temperatures are likely to drop to below 5°C
or exceed 30°C. For temperatures below 20°C allow the
EXPANSION JOINTS adhesive to cure for an extended period of time. If uncertain
Movement joints must be incorporated in the tile layout in check to see if the adhesive has set before allowing foot
accordance with AS3958.1-2007. traffic or grouting.

MIXING GROUTING
20kg of Superfixall powder requires approximately 5 litres Use the appropriate ASA grout with ASA Grout Additive as a
of water which produces 14 litres of mixed product. Add a total water replacement when tiling over flexible substrates.
measured amount of clean water into a clean container Allow joint widths of 1.5mm to 5mm for walls and 3mm to
and sprinkle Superfixall powder slowly into the liquid with 15mm for floors as per AS3958.1-2007. Thoroughly clean
constant stirring. Eliminate lumps. Mix to a thick toothpaste the surface of the tiles to remove all residue prior to the
consistency. Allow to stand for 2 minutes then remix. The grout and Grout Additive drying.
Index

SUPERFIXALL Technical Data Sheet

CLEAN UP SHELF LIFE


Superfixall can be removed from the surface of the tiles Unopened bags can be stored for up to 12 months in a cool,
using a damp cloth while the adhesive is still wet. Tools and dry and weatherproof environment. Bags must be stored off
equipment can be cleaned with warm water and detergent the floor.
prior to the adhesive drying.
LIMITATIONS
PACKAGING • Not suitable for tiling over flexible substrates, such as
Off White: 20kg paper bags and 5kg plastic bags. White: 20kg fibrous cement sheeting, plasterboard and timber.
paper bags. • Not suitable for tiling directly onto timber, plywood or
particleboard.
POT LIFE • Not suitable for tiling over waterproofing membranes
2.5 hours at 22°C and 50%RH unless it is an ASA or Bostik approved product.
Setting time: 24 hours at 22°C and 50%RH. • Not suitable for tiling directly on to metals or plastic
substrates.
COVERAGE • Not suitable for tiling directly onto polyurethane
3kg powder per m2­using a 6mm x 6mm notched trowel and membranes, contact ASA for further information.
6kg powder per m2 using a 12mm x 12mm notched trowel. • Not suitable for moisture sensitive tiles or stone.
• Do not mix or apply adhesives in temperatures below
SAFETY DIRECTIONS 5°C and above 30°C and under extreme hot and windy
Avoid contact with skin and eyes. Avoid breathing dust. Wear conditions.
overalls,safety shoes,impervious gloves and chemical goggles.
Use only in well ventilated areas. If inhalation risk exists wear PHYSICAL PROPERTIES
dust respirator. No smoking. Avoid contact with foodstuffs, Appearance: Cementitious off white and white powder
and sources of heat and ignition. Wash hands thoroughly Bulk density: 1.50 g/cm3
after use. Store in a cool place and out of direct sunlight. Mixing SG: 1.80 g/cm3
Store away from oxidising agents. Do not empty into drains.
Mixing ratio: 5 litres of water to 20kg of product

RISK: Irritating to eyes, respiratory system and skin. Risk of Pot life: 2.5 Hours at 22°C and 50%RH
serious damage to eyes. Harmful: danger of serious damage Open time: 30 minutes at 22°C and 50%RH
to health by prolonged exposure through inhalation.
MECHANICAL PROPERTIES
FIRST AID: If poisoning occurs, contact a Doctor or Poisons Tensile strength: 0.90 N/mm2
Information Centre, New Zealand 0800 764 766. After immersion: 1.11 N/mm2
Heat ageing: 0.60 N/mm2
For further information please refer to safety data sheets
Freeze/Thaw: 1.00 N/mm2
at www.bostik.co.nz
Classification (as per AS4992.2) C1E
DISCLAIMER: This datasheet is for the general help of users. It is provided in good faith. The data is current and accurate to the best of our knowledge. Differing materials, substrates,
environments, site conditions, and product storage, handling and application may affect results. Users should carry out tests to decide the product’s suitability for purpose. This data sheet and
the properties of the product may change without notice. Users, suppliers and retailers should check that the data sheets they have are the latest. To the maximum extent permitted by law,
Bostik disclaims all warranties in relation to manufacture and use of the product. Bostik is not liable for representations made by users, suppliers or retailers about the product. Bostik is not
liable for any loss or damage resulting from incorrect, careless, or negligent use or storage of the product, including use of out of date product. Any liability arising from use of the product is
limited to the replacement or purchase price of the product. Bostik does not exclude rights and remedies that cannot be excluded by legislation, for example under the Consumer Guarantees
Act 1993. Sale of the product by Bostik is subject to the Bostik New Zealand Limited Conditions and Terms of Sale. For more information on Bostik, products, and conditions of use and sale
visit www.bostik.co.nz

TECHNICAL SERVICES TOLL FREE NUMBER


NZ 0508 222 272 (land lines only) or visit www.bostik.co.nz

GUARANTEE ASA guarantees this product for 10 years provided application is in accordance with manufacturer’s directions and the
Australian Standards for Tiling Practice. ASA’s liability is limited to the cost of replacing effected ASA product only. ASA reserves the right
to inspect. Contact ASA for full guarantee terms.

Potrebbero piacerti anche