Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
WINTERGRADE BALLOXY HB
LIGHT
Product description
Wintergrade Balloxy HB Light is a two pack modified epoxy coating intended for use at
temperatures between -5°C and 10°C.
Recommended use
Wintergrade Balloxy HB Light is intended for use in water ballast tanks, on steel behind insulation,
in cofferdams and areas with condensation and where blast cleaning may not be possible.
Physical properties
Colour Beige, Green
Solids (vol %)* 71 ± 2
Flash point 35ºC ± 2 Setaflash
Gloss Flat
Water resistance Excellent
Abrasion resistance Very good
Solvent resistance Good
Chemical resistance Good
Flexibility Good
*Measured according to ISO 3233:1998 (E)
Bare steel
Cleanliness: Power tool cleaning to min. St 2, mill scale free (ISO 8501-1:1988). Improved
surface treatment (blast cleaning to Sa 2½) will improve the performance.
Shopprimed steel
Clean, dry and undamaged approved blast-primer.
Coated surfaces
Clean, dry and undamaged compatible primer. Contact your local Jotun office for more
information. For maintenance UHPWJ to WJ2 (NACE No.5/SSPC-SP 12) or Power tool cleaning to
min. St 2 for rusted areas
Other surfaces
The coating may be used on other substrates. Please contact your local Jotun office for more
information.
Application methods
Spray Use airless spray
Brush Recommended for stripe coating and small areas, care must be taken to
achieve the specified dry film thickness.
Roller May be used for small areas but not recommended for first primer coat,
however when using roller application care must be taken to apply sufficient
material in order to achieve the specified dry film thickness.
Application data
Mixing ratio (volume) 3 parts Comp. A (Base) to be thoroughly mixed with 1 part Comp. B
(Curing agent).
Induction time 10 minutes.
Pot life (23°C) 1½ hours.
Thinner/Cleaner Jotun Thinner No. 17
Guiding data airless spray
Pressure at nozzle 15 MPa (150 kp/cm², 2100 psi.)
Nozzle tip 0.53 - 0.79 mm (0.021 - 0.031")
Spray angle 40 - 80°
Filter Check to ensure that the filters are clean.
Note REMARKS:
* The temperature of the mixture of base and curing agent is
recommended to be at least 15°C, otherwise extra solvent may be
required to obtain correct viscosity.
* Too much solvent results in lower sag resistance and slower cure.
* Thinner should be added after mixing components.
1. The surface should be free from chalking and contamination prior to application. Best
intercoat adhesion occurs when the subsequent coat is applied before the preceding coat has
cured. If this is exceeded it may be necessary to roughen the surface.
The given data must be considered as guidelines only. The actual drying time/times before
recoating may be shorter or longer, depending on film thickness, ventilation, humidity, underlying
paint system, requirement for early handling and mechanical strength etc. A complete system
can be described on a system sheet, where all parameters and special conditions could be
included.
Storage
The product must be stored in accordance with national regulations. Storage conditions are to
keep the containers in a dry, cool, well ventilated space and away from source of heat and
ignition.Containers must be kept tightly closed.
Handling
Handle with care. Stir well before use.
Packing size
20 litre unit: 15 litres Comp. A (base) in a 20 litre container and 5 litres Comp. B (base) in a 5
litre container
Packing may vary from country to country according to local requirements.
For detailed information on the health and safety hazards and precautions for use of
this product, we refer to the Material Safety Data Sheet.
DISCLAIMER
The information in this data sheet is given to the best of our knowledge based on laboratory
testing and practical experience. However, as the product is often used under conditions beyond
our control, we cannot guarantee anything but the quality of the product itself. We reserve the
right to change the given data without notice.
Head Office & Nordic Europe Middle East South East Asia
Jotun Paints Jotun Paints (Europe) Ltd. Jotun U.A.E Ltd. LLC. Jotun (Singapore) Pte. Ltd.
P.O. Box 2021 Stather Road, Flixborough Al Quoz Industrial Area No 11-15, Sixth Lok Yang Road
N-3248 Sandefjord North Lincolnshire DN15 8RR P.O Box 3671 Jurong
Norway United Kingdom Dubai U.A.E Singapore 628 111
Phone +47 33 45 70 00 Phone +44 172 44 00 000 Phone +971 4 3 39 50 00 Phone +65 6265 4711
Fax +47 33 46 46 13 Fax +44 172 44 00 100 Fax +971 4 3 38 06 66 Fax +65 6265 7484
Jotun is a World Wide company with factories, sales offices and stocks in more than 50 countries. For your
nearest local Jotun address please contact the nearest regional office or visit our website at www.jotun.com
PDF Version :