Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
LINEAR BEARINGS
LINEAR BALL BEARINGS:
Drawn Cup, Solid, Stroke, Linear Flat Roller,
and Linear Roller Bearing Types
Linear Ball Bearings NTN
KLM
KLM 06 LL/3AS
KLM‥S
B-276
Linear Ball Bearings NTN
B-277
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 278
Suffix
This type composed of an outer ring, LL: Seal
steel balls and a cage is a cylindrical 3AS: Grease
bearing for the most universal Shaft diameter
Width
applications, which ensures precise and φ10―φ80
smooth infinite linear motion due to its Outer diameter
outer ring of high rigidity. Roller set bore
diameter
Type code
FF
FF‥ZW
This type composed of a cage and FF 25 18 ZW
needle rollers ensures smooth
reciprocating motion of less friction Suffix
ZW: Double row
actor by being inserted between two
planes in relative position. The cage Roller diameter Width
made of polyamide resin is provided φ2―φ3.5
with grooved joint at its both ends so Roller diameter
×10
several cages can be jointed together
into one unit. Type code
BF(RF)
RLM
RLM 26 × 86
This type is composed of a track frame,
a separator and rollers. This type has Bearing overall
length
the function enabling cylindrical rollers to Section height
circulate within the track frame and Section height
16―38
ensures infinite linear motion on a plane.
Type code
B-278
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 279
Section height: 26 ○ ○ ×
Bearing overall length: 86
B-279
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 280
Cage
How to mount
Fig. 1
The Type KH (drawn cup) bearing is press-fitted into
the housing in interference fit mode: therefore this type of
bearing does not need axial positioning with a means
such as a snap ring. For press-fitting, force the marking
Dimensional accuracy side on the outer ring with a mandrel illustrated in Fig. 2.
Because of its thin-walled outer ring, the Type KH The Type KLM (solid type) cannot be locked to the
(drawn cup type) unavoidably develops certain degree of housing by interference alone. This type of bearing needs
deformation in various manufacturing steps, in particular to be axially located with a snap ring.
in the heat treatment process. Nevertheless, this bearing
type has been designed so that when press-fitted into a
housing of accurate dimensions, its deformation is
corrected and it can restore its original accuracy to fully
develop its design functions. For a method for
15˚
determining dimensional accuracy of this bearing, contact
NTN Engineering for technical assistance.
The dimensional accuracies in boundary dimensions,
ball set bore diameter (Fw), outside diameter (D) and
B Marking side
width (C) of the Type KLM (solid type) are listed in the
relevant dimension table. Upon request, NTN will supply
linear ball bearing products for higher accuracy. For
details, contact NTN Engineering.
A
Bearing fit
A=Fw−(0.03∼0.04)mm
By employing a shaft or housing featuring dimensional B=D−(0.2∼0.3)mm
tolerance in Table 1 in this page, an appropriate radial
internal clearance can be provided in the installed Fig. 2 Series KH
bearing. When a further smaller radial internal clearance
is needed, achieve selective fit to obtain an intended
radial internal clearance by selecting a relevant bearing-
shaft or bearing-housing combination.
Accessories
Table 1 Bearing fit Shafts, shaft support stands and housings exclusive for
Type Shaft Housing NTN linear ball bearings are also offerable. Feel free to
contact NTN for the detailed information.
series HK H7 (H6) - steel series -
h6 (j5)
Drawn-cup type K7 (K6) - light metal alloy series -
series KLM
g6 (g5) H7 (H6)
Solid type
Note) The parenthesized data is applied to shaft/housing subjected to higher
accuracy or of vertical construction.
B-280
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 281
Type KH
Type KH‥LL
With seal
FW 6〜50mm
Note 1) Showing a-value from the side face with stamped mark thereon.
2) Imported product from INA, Germany.
B-281
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 282
With seal
FW 3〜35mm
B-282
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 283
FW 40mm
B-283
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 284
B-284
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 285
Fig. 2
S:Stroke
S/2
Fig. 3
S/4 S/4
Fig. 4
B-285
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 286
Type KD
Type KD‥LL
FW 10〜80mm
10 19 30 1.7 0.4 1.5 22.7 27 15.5 19 KD101930 KD101930LL/3AS 720 535 74 55 0.028 0.030
12 23 32 1.7 0.4 1.5 24.5 30 17.1 22 KD122332 KD122332LL/3AS 920 725 94 74 0.052 0.055
16 28 37 1.7 0.5 1.5 29.1 33 21.1 26 KD162837 KD162837LL/3AS 1 480 1 070 151 109 0.073 0.078
20 32 45 2.2 0.5 2 35.8 55 26.8 46 KD203245 KD203245LL/3AS 1 670 1 230 171 125 0.100 0.105
25 37 45 2.2 0.6 2 35.8 55 26.8 46 KD253745 KD253745LL/3AS 1 890 1 410 192 144 0.115 0.120
30 45 65 2.7 0.7 2.5 53.5 81 45.1 73 KD304565 KD304565LL/3AS 3 800 3 100 390 315 0.265 0.265
35 52 70 2.7 0.7 2.5 58.5 90 50.1 79 KD355270 KD355270LL/3AS 4 200 3 500 430 355 0.405 0.405
40 60 80 2.7 0.7 2.5 68.3 103 59.9 93 KD406080 KD406080LL/3AS 5 900 4 750 600 485 0.635 0.635
45 65 80 2.7 0.7 2.5 68.3 103 59.9 93 KD456580 KD456580LL/3AS 6 400 5 300 655 540 0.675 0.680
50 72 100 3.2 1 3 86.4 136 77.4 125 KD5072100 KD5072100LL/3AS 8 500 6 850 870 695 1.00 1.02
55 80 100 3.2 1 3 86.4 136 77.4 125 KD5580100 KD5580100LL/3AS 9 200 7 550 940 770 1.34 1.36
60 85 100 3.2 1 3 86.4 136 77.4 122 KD6085100 KD6085100LL/3AS 9 900 8 250 1 010 840 1.41 1.43
70 95 100 3.2 1 3 86.4 136 77.4 122 KD7095100 KD7095100LL/3AS 10 600 9 000 1 080 920 1.61 1.63
80 110 100 3.2 1.2 3 86 129 77 116 KD80110100 KD80110100LL/3AS 13 300 10 900 1 350 1 110 2.37 2.40
Note 1) The tolerance for dimension-C is 0, -0.120 mm against Fw≦50 mm and 0, -0.150 mm against Fw>50 mm.
B-286
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 287
B-287
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 288
Types
For Type FF, the polyamide resin cage has a dovetail L=S/2+L1 …………………………………………(1)
joint groove on its both ends so that several cages can be
jointed together into one unit.
For Type FF‥ZW, two rows of needle rollers are
L1 S
configured in the cage and the cage has an elastic joint
on its center so as to enable to bend two rows of flat
rollers to any optional angle at the elastic joint by heating
them in oil of 70 to 90˚C. The two roller rows bent to any
optional angle can hold the bent shape unchanged, even
S/2
under normal operating temperature, by being cooled
L
down for several seconds, with the bending angle held
unchanged. Fig. 2
For Type BF, the cage is press-formed from steel plate
and the standard length of the bearing unit is 1000 mm.
For Type RF, the cage is of polyamide resin and the
standard length of the bearing unit is 705 mm. The both The linear flat roller bearing results in moving deviation
are unavailable for cage to cage inter-jointing, but a due to profile deviation of raceway surface, uneven load
bearing unit of any desired length is offerable upon or vibration. Therefore, the table or the bed must be
request. Feel free to contact NTN for the detailed equipped with a stopper at its end portion to prevent over-
information. run of the flat roller bearing. (Fig. 5)
Figs. 3 and 4 illustrate application examples of the
linear flat roller bearing unit.
Needle roller tolerance If a separate raceway surface having undergone heat
The needle rollers contained in the flat roller cage are treatment and grinding is installed to a machine main
manufactured within the dimensional tolerance range of 0 body, be careful to avoid deformation of the bearing that
to -2 mm against the nominal diameter (Dw). can result from tightening.
Inclination
B-288
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 289
Stopper
Fig. 5
B-289
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 290
Type FF
Type FF‥ZW
DW 2〜3.5mm
2.5 15 35 45 9.8 2.4 29 300 82 500 2 980 8 450 FF2535ZW 16 35.3 +0.1
0
0
2.2 −0.2 0.0082
3 20 − 60 13.8 3 31 000 79 500 3 150 8 100 FF3020 9 20.4 +0.1
0
0
2.7 −0.2 0.0089
3.5 25 55 75 17.8 3.2 86 000 265 000 8 800 27 000 FF3555ZW 20 55.4 +0.1
0
0
3.2 −0.2 0.035
B -290
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 291
Type BF
Type RF
Type RF Type BF
DW 3〜7mm
3 20 705 13.8 6 4.5 34 000 88 500 3 450 9 000 RF3020/705 20.4 +0.1
0
0
2.7 −0.2 0.015
3 20 1 000 15.8 6 5 38 000 102 000 3 850 10 400 BF3020/1000 20.4 +0.1
0
0
2.7 −0.2 0.037
+0.1 0
5 23 1 000 19.8 8 8 87 000 211 000 8 850 21 500 BF5023/1000 23.4 0 4.7 −0.2 0.054
5 32 1 000 27.8 8 8 114 000 299 000 11 600 30 500 BF5032/1000 32.4 +0.1
0
0
4.7 −0.2 0.073
+0.1 0
7 28 1 000 24 11 10.5 138 000 305 000 14 000 31 000 BF7028/1000 28.5 0 6.7 −0.2 0.091
7 35 1 000 30 11 10.5 185 000 445 000 18 900 45 500 BF7035/1000 35.5 +0.1
0
0
6.7 −0.2 0.110
B -291
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 292
This roller bearing with cylindrical rollers having the Table 2 Requirements for raceway surface and mounting
function capable of circulating within the raceway block surface (recommended)
ensures smooth infinite linear motion on a flat surface. Characteristics Allowable value or tolerance range
The cylindrical rollers are retained and guided by the
Raceway surface roughness (max) 0.2a
cage and the ribs of the raceway block.
The cage is of such a construction as not allow Raceway surface hardness HRC58∼64
adjacent rollers to contact with one another. Hence, the Effective hardened layer depth of as described in applicable
friction coefficient is low. raceway surface (min) Dimensions Table
Parallelism of mounting surface
∆ x(See Fig. 2) 0.05 mm per 100 mm
∆ y(See Fig. 3) 0.01 mm per 100 mm
Fig. 1 Fig. 2
Bearing accuracy
All the linear roller bearings are manufactured within
the dimensional tolerance range of 0 to -2.5μm for
bearing height (H). And these bearings are delivered
classified into 5-stepped tolerance classes. (See Table 1)
Fig. 3
Table 1 Classification of bearing height H by accuracy class
Unit : μm
B-292
*直線運動用-B275-B293-E/8.5_*直線運動用/B275-B293/E 11/05/25 13:46 ページ 293
Type RLM
Section Z-Z
H 16〜38mm
16 25 62 8 17 19 M4 35.5 12.5 6 φ3.2 RLM16× 62A 15 400 34 000 1 570 3 450 0.3 0.11
19 27 69 10 25.5 20.6 M4 43.4 15.5 6 φ3.2 RLM19× 69B 26 100 58 000 2 660 5 900 0.3 0.16
26 40 86 14 28 30 M6 52.4 21 10 φ4.5 RLM26× 86A 50 000 106 000 5 100 10 800 0.4 0.41
26 40 102 14 44 30 M6 67.9 21 10 φ4.5 RLM26×102A 62 500 142 000 6 350 14 400 0.4 0.53
26 40 126 14 68 30 M6 91.8 21 10 φ4.5 RLM26×126A 80 000 195 000 8 150 19 900 0.4 0.70
38 52 134 20 51 41 M8 85.7 31 14 φ6.5 RLM38×134B 124 000 270 000 12 600 27 500 0.5 1.3
B-293