Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
SULTANATE OF OMAN
TECHNICAL CHECKLISTS
FOR
LT, 11KV & 33KV PRODUCTS & MATERIALS
MAY-2012
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with
the product approval application will not be
accepted.
CONTENTS
PART - I - 33 KV
U
1 ON-LOAD DISCONNECTOR 4
2 AUTO RECLOSER 9
3 STAY INSULATOR 12
4 XLPE CABLES 16
5 LINE POST INSULATOR 18
6 3.6, 10 & 20 MVA TRANSFORMERS 21
7 OUT DOOR BREAKER 36
PART - II - II KV
U
1 ON-LOAD DISCONNECTOR 40
2 DROP OUT FUSE 45
3 AUTO RECLOSERS 48
4 INDOOR SWITCHGEAR 51
5 DISTRIBUTION TRANSFORMERS 65
6 RING MAIN UNIT 70
7 XLPE CABLES 74
8 LINE POST INSULATORS 77
9 STAY INSULATORS 80
1 800/1600 A FEEDERPILLARS 83
2 400 A MINI FEEDER PILLARS 86
3 400 A CUTOUT BOX 89
4 CONSUMER UNIT 92
5 SHACKLE INSULATOR 95
6 STAY INSULATOR 97
7 XLPE CABLES 99
8 XLPE COVERED ALUMINIUM CONDUCTOR 102
9 SINGLE PHASE/THREE PHASE KWH METERS 105
PART IV - GENERAL
U
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
1
GENERAL REQUIREMENTS
……
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
2
PART – I
33 KV
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
3
33 KV ON-LOAD DISCONNECTOR
Description Requirements
9. Documents to be submitted with the i) Check list signed and stomped bv the
Approval request, Manufacturer
ii) Technical literature
iii) Installation & Operation manual
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
4
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Subgmission Compliance
No.
Outdoor Mounting on H-Type
Type
01 Wood Pole Structure
03 Conforming To BS 5253
Mounting Height
04 of the Switch
9000 MM
Mounting Height
07 of Operating 1200 MM
Handle
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
5
SL
Items Requirement Submission Compliance
No.
Lined with Horn Fiber or
Head equivalent for ARC
Quenching and Contacts
Interrupter
Tipped with Copper Tungsten
09 Head
ARC Extinguishing contact
follower, Large Volume
Exhaust Muffler.
Cree page of
12 1320 MM
Insulators
Note :- If any of the above IS not complied with. the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
6
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
Outdoor - Vertical Mounting on
Type
01 H-Type Wood Pole Structure
Mounting Height
04 of they Switch
7700 MM
Wood Pole
06 Centers H-Type 1800 MM
Construction
Mounting Height
07 of Operating 1200 MM
Handle
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
7
SL
Items Requirement Submission Compliance
No.
Lined with Horn Fiber or
Head equivalent for ARC
Quenching and Contacts
Interrupter
Tipped with Copper Tungsten
09 Head
ARC Extinguishing contact
follower, Large Volume
Exhaust Muffler.
Cree page of
12 1320 MM
Insulators
20 Sample Required
Operation
21 Required
Checking
Test Certificate from
22 Independent Required
Authority
23 Reference List Required
Note :- If any of the above Is not complied with, the products approval application will not be accepted,
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
8
33 KV AUTO RECLOSERS
U
Description Requirements
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
9
PRODUCT APPROVAL WORKING GROUP
U
33 KV AUTO RECLOSER
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
Wood Pole Mounted SF6
Type Insulating Medium and
01
Vacuum Interrupter
02 Service Voltage 33 KV
Highest System
03 Voltage
36 KV
Normal Current
04 Rating
400 A
05 Breaking Capacity 6 KA
Operating Duty
Up to 4 Clearances in
08 Succession
Cree page
09 Of bushing
1320 MM
Power Frequency
Withstand Test:-
10
- Dry for 60 Sec.
- Wet for 60 Sec 70 KV
60 KV
Porcelain or Silicon Rubber
11 33 KV Bushing
Required
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
10
33 KV AUTO RECLOSER
U
SL
Items Requirement Submission Compliance
No.
1. Fully Micro-processor
Controlled and Programmable
Settings. Controls and Settings
are to be Programmable by
12 Control hand held device at Local/Site
without PC or Laptop
I
2. Type
Note :-If any of the above IS not complied with, the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
11
33 KV AUTO RECLOSER
U
SL
Items Requirement Submission Compliance
No.
15 Protection:- 25% - 200% in Steps of 25%
- Over Current
Setting 4 – 20
- Over Current
Instantaneous' 0,1 - 1.5 in Steps of 0,1
- Over Current
Time Multiplier 10% - 80% In Steps of 10%
- Earth Fault
Current Setting 4 – 20
- Earth Fault
Instaneous 0.2 - 25 Secs,
(Selective)
- Earth Fault Time 1 - 60 Secs
Delay
- Recluse Time 1 - 180 Secs
Selectable
- Reclaim Time Local Control Operated
Selectable manually with Hook Stick
- Local Control Comprising.
A) Manual Close
B) Close and Lock-In
C) Trip and Lock-Out
D) Earth Fault In/Out
Painting and
17 Required
Finish
Note:- If any of the above Is not complied with. the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
12
33 KV STAY WIRE INSULATOR
U
Description Requirements
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
13
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
Impregnated Laminated Wood I
01 Material
or Fiber Polyester Resin
As per Drawing
05 Dimensions
No. MEW/OH/015A/0l5C
Test Certificate
06 From Independent Required
Authority
07 Sample Required
Note ;. If any of the above Is not complied with. the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
14
33 KV XLPE CABLES
U
Description Requirements
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
Ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
15
PRODUCT APPROVAL WORKING GROUP
U
33 KV XLPE CABLES
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
Highest System
02 Voltage
36 KV
Extruded Semi-Conductive
04 Conductor Shield
Layer
06 Thickness 9MM
Extruded Semi-Conducting
Layer, Phase Identification -
07 Insulation Shield Red, Yellow and Blue, Bare
Copper Shielding Tape applied
with a Lap
08 Fillers and Bound with Non
Vulcanizable Tape suitable for
Assembly
Conductor Temperature 900
DEG,C
09 Sheath Extruded PVC B 6746 - Table-I,
Type-9
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
16
SL
Items Requirement Submission Compliance
No.
10 Thickness of Sheath 2 MM
Thickness of
12 Bedding
0.6 MM
19 Sample Required
Note :- If any of the above is not complied with. the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
17
33 KV LINE POST INSULATOR
U
9. Documents to be submitted with the a) Check list signed and stamped by the
Approval request. Manufacturer
b) Technical literature
c) Installation & Operation manual if
applicable
d) Drawings
e) Experience List
f) Test Certificates
g) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
18
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
Nominal System
02 Voltage
33 KV
System Highest
03 Voltage
36 KV
Minimum Dry
04 Impulse Withstand
250 KV
Minimum Wet
05 Power Frequency 135 KV
Withstand
Minimum
06 Mechanical Failing 11 KN
Load
Minimum
07 Cree page
1320 MM
08
Aerodynamic Open Profile
Profile Sheds Top and Side Groves
Uniform Sheds
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
19
SL
Items Requirement Submission Compliance
No.
Fixing Stud :-
16 MM
- DIA - 86MM
10 - Length (A) - 203MM
- Length (B) - 71.4 MM
- Thread (A) - 102MM
- Thread (B)
Test Certificate
13 From Independent Required
Authority
Sample Predicted
14 Required
For Inspection
Note :- If any of the above Is not complied with, the product approval application will not be accepted,
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
20
3, 6, 10 & 20 MVA POWER TRANSFORMERS
U
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
21
PRODUCT APPROVAL WORKING GROUP
U
(GENERAL RQUIREMENTS)
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
IEC 76
01 Standard
BS 171
Temp. rise over
Ambient of 50 Deg.C:- 40 Deg. C
02
- 011 by Thermometer 50 Deg. C
-Winding by Resistance
Maximum
03 continuous Rating
3/6/10/20 MVA
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
22
SL
Items Requirement Submission Compliance
No.
Core:-
A) Core Plate/ Required
Lamination
Insulation
B) Core Clamping Required
Bolts and Plate
Insulation
10
C) Core Lifting Required
Device
D) Provision for Required
support to
prevent
movement
during transport
Winding:-
A) Conductor High Conductivity Electronic
B) Max. Current Copper not greater than
density 2.6A/SQ.MM.
C) Type of Winding
D) Method of
11 Bracing and
Clamping
E) Ability to
withstand
shock
during handling
and transport
13
Ability to withstand
lightning surges
and switching
surges
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
23
SL
Items Requirement Submission Compliance
No.
Internal earthling
arrangement for
core clamping
14
STR., damping
bolts and coil
clamping ring
16 Main Tanks:-
A) Lifting Required
arrangement
B) Accessibility to
termination of
windings and
earthing point
without
emptying the oil
tank
C) Tank withstand
Required
pressure when
A vacuum of 50 CM of
empty
mercury or vacuum required
for drying out whichever IS
Greater
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
24
3 MVA 33/11.5 KV TRANSFORMERS
U
(PARTICULAR RQUIREMENTS)
U
SL
Items Requirement Submission Compliance
No.
01 Type OMAN
03 Connections Delta/Star
6%
07 Impedance
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
25
SL
Items Requirement Submission Compliance
No.
09 Fittings:-
- Conservator Tank
- Silicagel Breather
- Ammeter 0 - 400A
with Hand Reset
maximum
demand
indicator
- Pressure relief
device
- Oil Temp.
Indicator
- Lifting and
Jacking Lugs
- Thermometer
Pocket
- Earthing Terminals
- Rating and
Diagram Plates
- Single Phase
Current T ransformer
400/5A
fitted on 11 KV "Y"
Phase for Ammeter
Service
10
Main Tank
Thickness of
Plates:-
- Top 15 MM
- Bottom 15MM
- Sides 8MM
- Radiator 1.2 MM
Note :-If any of the above is not complied with, the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
26
6 MVA 33/11.5 KV TRANSFORMERS
U
(PARTICULAR RQUIREMENTS)
U
SL
Items Requirement Submission Compliance
No.
01 Type OMAN
02 Voltage Ratio
33/11,5 KV
03 Connections Delta/Star
Pad Locking
06 Required
Facilities
07 Impedance 6%
08 Termination:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
27
SL
Items Requirement Submission Compliance
No.
09
Fittings:-
- Conservator Tank Required
- Silicagel Breather Required
- Ammeter 0 - 400A
with Hand Reset
maximum demand
Indicator Required
- Pressure relief
device Required
-Oil Temp, Required
Indicator
Required
- Lifting and Required
Jacking Lugs
- Thermometer Required
Pocket
- Earthing Terminals Required
- Rating and Required
Diagram Plates
- Single Phase Required
Current Required
Transformer 400/5
fitted on 11 KV
Class
5PlO
10
Main Tank
Thickness of
Plates:
- Top 15 MM
- Bottom 15 MM
- Sides 8MM
- Radiator 1.2 MM
Note :- If any of the above Is not complied with, the product approval application will not be accepted,
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
28
10 MVA 33/11.5 KV TRANSFORMERS
U
(PARTICULAR RQUIREMENTS)
U
SL
Items Requirement Submission Compliance
No.
01 Type OMAN
02 Voltage Ratio
33/11,5 KV
03 Connections Delta/Star
Tapping: On Load
05
- Range + 5% to - 15%
- Step 1.66%
06 Impedance 7.5%
07 Termination:
-33 KV Side Cable Box Suitable for 3C x
300 Sqm X LPE Cable
Clearance - 500 MM Creepage Phase to
Creepage Earth - 400 MM 805MM
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
29
SL
Items Requirement Submission Compliance
No.
08 Current
Transformer
33 KV Side '-
- Ratio
- Class 200/1
- VK X
330V
2 Double Core
C.T. for OlC.
ElF and metering
Ratio,
- Class 200/1A
Class-5PlO for protection
11 KV Side - and
- REF Protection Class - 1 for metering
- Ratio
- Class X 600/lA
- Standby ElF X
- Ref Relay
- Ratio
- Class
600/lA
5P 10
09
Main Tank
Thickness of
Plates:
- Top 20 MM
- Bottom 20 MM
- Sides 10 MM
- Radiator 1.2 MM
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
30
SL
Items Requirement Submission Compliance
No.
Buchholz Relay
10 Type and Make
Required
On-Load Tap
11 Changer Type and
Make
progress I
- Lamp & Buzzer
Out of step Lamp
Voltage Regulations relay
With Time Delay
Operating Coil
30V DCI 11 OV DC
Note :- If any of !he above is not complied with, the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
31
20 MVA 33/11.5 KV TRANSFORMERS
U
(PARTICULAR RQUIREMENTS)
U
SL
Items Requirement Submission Compliance
No.
01 Type ONAN
Dyn 11
04 Vector Group
On Load
Tapping:
05 + 5"10 to - 15"10
- Range
1.667"10
- Step
Impedance
06 Voltage
12.5%
07 Terminations:
- 33 KV Side:-
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
32
SL
Items Requirement Submission Compliance
No.
Current
Transformers.
Particulars:-
33 KV Side:-
Separate
3 Phase set of CT's
for diff. Protection
- Ratio
- Class
08 11 KV Side :-
400/1A
For REF
- Ratio
- Class
1200/1A
2. Stand by E/F &
X
Meters
- Ratio
1200/1
- Class
5P10
Main Tank Material
Thickness
- Top 20 MM
09 - Bottom 20 MM
- Sides 10 MM
1,2 MM
- Radiator
Buchholz Protection Required
For Main TX
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
33
SL
Items Requirement Submission Compliance
No.
Marshalling KIOSK:-
- Location
- Winding Temp.
Indicator
12 - Oil Temperature Adjacent or on the Top
Indicator
- Local/Remote
Tap change
Selector
Switches
Safety Pressure
Operated By Spring Loaded
13 Release Device
Mechanism Required,
for Main TX.
14 Safety Pressure Diaphragm Rupturing Type
Release Device -Required
for On- Load Tap
Changer
Note :- If any of the above Is not complied with, the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
34
SL
Items Requirement Submission Compliance
No.
15 Tap change 1Digital Tap Position Indicator
Tap Change Raise and lower
control Panel 2 Spring loaded switches or push
Button
Tap Changer Control Switch
3
Remote! /Supervisory
Tap Change in Progress
4
indication and buzzer
5 Out of Stop Lamp indication
Voltage Regulating Relay with
6
Time Delay
Tap Changer Control
7
Auto/Non-Auto Selector Switch
A VR Voltage Reference
8
Adjuster
9 VT Fail Alarm
Supply Voltage of OLTC
10
failure - Amber Lamp
0-lS KV Voltmeter
11
Tap Changer Motor MCB OFF
12
indication (Amber)
Emergency Stop Push Botton
13
Oil Temp. Alarm
14
Oil Temp, Trip
15
Winding Temp, Alarm
16
Winding Temp Trip
17
Buchholz Relay Alarm
18
Buchholz Re-lay Trip
19
Oil Level Low Alarm
20
21 Pressure Device Trip
Note:- If any of the above Is not complied with, the product approval application will not be accepted,
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
35
33 KV OUTDOOR BREAKER
U
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
Note :- If any of the above Is not complied with, the product approval application will not be accepted.
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
36
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL Submiss
Items Requirement Compliance
No. ion
Metal Clad. Fully SF6 Breaker or
01 Type Vacuum Interrupter With SF6
Insulating Medium
Rupturing
02 25 KA for 3" Duration
Capacity
Degree of
04 Protection
IP 65
System Normal
05 Voltage
33 KV
Highest System
06 Voltage
36 KV
09 Frequency 50 HZ
Operating
Mechanism :-
- Spring 240V 50 CIS
Charged Motor
110V or 30V DC
- Closing Coil
10 Voltage
- Shunt Trip Coil
110Vor 30V DC
- Manual Charging Required
Indictor
- On/Off Control Required
Local/Remote
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
37
SL
Items Requirement Submission Compliance
No.
11 Operating
Cubicle ;-
- Weather Proof
- Highest Live Required
Part from
Bottom 3.0 MTR
Current
12 Transformers
Required
14 Heater Required
Type Tests
15 Certificate from Required
Independent Lab
Terminal Bushing
- Type Aerofil Open Profile
16 - Creepage 1320 MM
- Clearance -
Phase to Phase 470MM
Breaker Operation
17 Counter
Required
18 Terminals Copper
Mounting
Structure ;-
Galvanizing Thickness 127
19 - Protection
Microns
against
Corrosion
2.5Sqmm Stranded Copper
PVC Insulated. All
20 Smallurrings
terminations Filled With
Ferrules and circuit number
Two Earthing Terminal of
Brass or Stainless Steel
21 Earthing suitable for Connecting 10
Sqmm Cu.
Conductor
Note :- If any of the above IS not complied with. the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
38
PART II
11 KV
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
39
11 KV ON - LOAD DISCONNECTOR
U
Required
6. Sample complying with the standard
To be submitted with the request
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
40
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL Submiss
Items Requirement Compliance
No. ion
03 Standard BS 5253
Mounting Height
04 of the Switch
9000 MM
05 Phase Centers
1050 MM
Mounting Height
07 of Operating 1200 MM
Handle
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
41
SL Submiss
Items Requirement Compliance
No. ion
Contacts Tipped with Copper
Head or Tungsten, Long Life are
Interrupter resistant Horn Fiber Bore Lining
09
Head ARC Extinguishing contact
follower, Large Volume Exhaust
Muffler,
10 Off/On Indicator Required
Pad Locking
11 Required
Faculties
Creepage of
12 440MM
Insulators
Load Breaking
14 400A at 0,70 pf
Capacity
20 Sample Required
21 Operation Required
Test Certificate
22 from Independent Required
Authority
Note :- If any of the above Is not complied with, the product approval application will not be accepted,
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
42
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL Submiss
Items Requirement Compliance
No. ion
Outdoor Vertical Mounting on
01 Type
H-Type Wood Pole Structure
General
02 Requirement OES - 11
Conforming To
03 Standard BS 5253
Mounting Height
04 7700 MM
of the Switch
Wood Pole
06 Centers H-Type 1800 MM
Construction
Mounting Height
07 of Operating 1200 MM
Handle
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
43
SL Submiss
Items Requirement Compliance
No. ion
Lined with Horn Fiber or
equivalent for ARC Quenching
Interrupter and Contacts Tipped with
09
Head Copper Tungsten; ARC
Extinguishing contact follower;
Large Volume Exhaust Muffler.
10 Off/On Indicator To be Provided
Creepage of
12 440MM
Insulators
20 Sample Required
Operation
21 Required
Checking
Test Certificate
22 from Independent Required
Authority
Note :- If any of the above Is not complied with. the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
44
11 KV DROP OUT FUSE
U
Required
6. Sample complying with the standard
To be submitted with the request
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
45
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL Submiss
Items Requirement Compliance
No. ion
Rating ;-
11 KV
- Nominal Volt. 12.5 KV
- Max. Voltage 95 KV
- Bill Different for Different Rating
- Cont. Current (KV A) for distribution
Transformers
- Interrupting 4.5 KA
01 440MM
Current
- Leakage
Symmetrical
Distance of
Support
Fast acting (Fuse should Blow
Insulators
first for Short Circuit inside
- Characteristics Transformer)
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
46
SL Submiss
Items Requirement Compliance
No. ion
Fuse Tube - Epoxy Fiber Glass Liner with
Horn Fiber
- Outer surface protected
05 with an Ultra-Violet
resistance finish
- Fire retardant
- Lifting ring for handling with
a hook stick
Arcing Horn
- Galvanized Malleable iron
adjustable 4 CM to 8 CM
06
- Clearance 6 CM from
Insulator Shed
Centre Distance
07 from Support 394MM
Insulators
Test Certificate
09 from Independent Required
Authority
Required
10 Reference List
Required
11 Sample
Required
12 Operation Check
Note :- If any of the above Is not complied with, the product approval application will not be accepted,
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
47
11 KV AUTO RECLOSERS
U
Required
6. Sample complying with the standard
To be submitted with the request
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates from Independent Lab
vii) Sample (when requested)
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
48
PRODUCT APPROVAL WORKING GROUP
U
11 KV AUTO RECLOSERS
U
MANUFACTURER :
AGENT :
DATE :
SL Submiss
Items Requirement Compliance
No. ion
Type Wood Pole Mounted SF6
Insulating Medium with
01 Vacuum Interrupter and HV
Bushings Porcelain or Silicon
Rubber
Highest System
03 Voltage
12.5 KV
Nominal Current
04 Rating
400 A
05 Breaking Capacity 6 KA
Creepage of
09 Busing
440MM
Power Frequency
Withstand
10 - Dry for 60 Sec. 50 KV
- Wet for 60 Sec. 45KV
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
49
SL Submiss
Items Requirement Compliance
No. ion
Protection :-
- Over Current Setting 25"10 - 200"10 in Steps of 25"10
Test Certificate
14 from Independent Required
Authority
Performance over
16 Required
one Load Cycle
Note :- If any of the above is not complied with. the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
50
11 KV SWITCHGEAR
U
Not Required
6. Sample complying with the standard
To be submitted with the request
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
51
PRODUCT APPROVAL WORKING GROUP
U
11 KV SWITCHGEAR (INDOOR)
U
MANUFACTURER :
AGENT :
DATE :
SL Submiss
Items Requirement Compliance
No. ion
Indoor Metal Clad
01 Type
Compartmental
Rating:-
- Normal Voltage 11 KV
03 - Highest Voltage 12,5 KV
- S,S,C, Voltage 18,4 KA
75 KV
- Impulse
Current Rating:-
400A
For Feeder
1200 A
04 For Transformer
For Bus Section
2000 A
For Bus Bar
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
52
SL Submiss
Items Requirement Compliance
No. ion
07 Circuits :-
No. of Panels 16
Standard
Arrangement of
S.G. Panels
- Panel No.1 Capacitor
and 16 Control
- Panel No.2 Stn. Tx. Control
- Panel Nos. 3 To
Feeder Control
7&l1To15
For 20 MVA Tx. Incomer
- Panel No.8
and 10 Control
D) One Ciruit
Breaker Control
Switch Located
Required
on Front the
Panel
E) CB. "Closed"
and "Open" Required
Red and Green
Indication
Lamps 5 Watts
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
53
SL Submiss
Items Requirement Compliance
No. ion
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
54
SL Submiss
Items Requirement Compliance
No. ion
09
Aux. Required
Transformer
Control Panel:-
A) One Circuit
Breaker 350
MVA 3 Phase 11
KV. 400 AMPS
B) Three Current
Transformers
Double core
100/50/5A 15VA
capacity
Class 1 - metering
Class 5 PlO
protection
C) One Cable Box
11 KV 3 Core
Cross Linked
Polyethylene
Steel Wire
Armored PVC
Sheathed -
Cable Size 50
Sq. MM
D) One Circuit
Breaker Control
Switch
Mounted on
Front of the
Panel
E) One Local/
Remote
Selector Switch
Mounted on
Front of the Panel ,
F) One Healthy Trip 5w. 30 VDC with
Indication
Resistance and Push Button
Lamp
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
55
SL Submiss
Items Requirement Compliance
No. ion
09
Aux. Required
Transformer
Control Panel:-
A) One Circuit
Breaker 350
MVA 3 Phase 11
KV. 400 AMPS
B) Three Current
Transformers
Double core
100/50/5A 15VA
capacity
Class 1 - metering
Class 5 PlO
protection
C) One Cable Box
11 KV 3 Core
Cross Linked
Polyethylene
Steel Wire
Armored PVC
Sheathed -
Cable Size 50
Sq. MM
D) One Circuit
Breaker Control
Switch
Mounted on
Front of the
Panel
E) One Local/
Remote
Selector Switch
Mounted on
Front of the Panel ,
F) One Healthy Trip 5w. 30 VDC with
Indication
Resistance and Push Button
Lamp
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
56
SL Submiss
Items Requirement Compliance
No. ion
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
57
SL Submiss
Items Requirement Compliance
No. ion
Required
B) Three Current
TXS. Class "X" for
overall biased
differential TX.
Protection with
1200/lAmp.
Ratio with CT
Characteristics
to suit the
Characteristics of the
Current TX. Son
33 KV side which
shall have a ratio
of 400/1 A Required
C) Double Core
Current Transformers.
One Core for
Restricted Earth
Fault Protection
Ratio 1200/1
AMP, Class "X"
and to match
with Line CTS.
The other core
For SBEF protection
1200/1 A 5PlO.
D) Three Double Required
Core Current TX.
Ratio 12oo/1A
15VA Class 5PlO
Accuracy for
Directional O/C
Protection and
Other Core
Class I for Metering
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
58
SL Submiss
Items Requirement Compliance
No. ion
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
59
SL
Items Requirement Submission Compliance
No.
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
61
SL
Items Requirement Submission Compliance
No.
12 Capacitor Control
Panel:- 350 MV A 3 Phase 11 KV
A) One Circuit 400 A
Breaker
B) Three Double Ratio Required
Current Transformers
400/5A 15VA Min.
Capacity. Accuracy Class
5P 10 for over Current and
Earth Fault Protection and
Class 1 for Metering.
C) One Cable Required
compartment
for 11 KV 3C 240
SQ, MM XLPEI
PVC/SWA/PVC
Required
D) One Circuit
Breaker Control
Switch Located
on Front of the
Panel 5W30VDC
E) Circuit Breaker
"Close" and
"Open" Red and
Green
Indication
Lamps.
F) One Local/
Remote Selector
Switch on Front
of Panel
G) One Healthy Trip 5W 3V DC with Series
Indication Lamp Resistance
H) Auto Trip Amber and Push Button
Indication Lamp 5W30VDC
I) Two Over Current
and One Earth Required
Fault IDMT Relays
J) One Ammeter Required
Scaled
0-400Amps with
Select or Switch
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
62
SL Submiss
Items Requirement Compliance
No. ion
13
Isolation and
Interlock:- Required
1) Locking out
each C.B, in the
Isolated or off
position,
2) Locking Required
movable
shutters
Creenlng Live
Parts (Lock to be
Coloured Red)
3) Locking C.B,
Control Switch Required
4) Locking V.T, in
the Rack in Required
Position
5) Locking V,T,
Spout Shutters, Required
All Locks to differ
and shall have
individual keys
6) Manual Required
Opening/
Closing of
Shutters
14
C.B, Isolating
Equipment
A) Integral
Earthing through Required
C,B, for Circuit
Earthing
B) Mechanical Required
Interlock
C) Earthing of Bus Required
Bar for the TX,
through the C.B,
D) Interlock with
Required
Bus Section
Breakers
E) Switchboard Required
Earth C U, Bus Bar
50X4MM
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
63
SL
Items Requirement Submission Compliance
No.
Additional
Equipment:-
Testing Plugs
Tool Cabinet
15
Key Cupboard
Permit To work
Locking off
Boxes
Test Certificate
16 from Independent Required
Authority
Note ;- If any of the above is not complied with, the product approval application will not be accepted,
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
64
11 KV /433 V DISTRIBUTION TRANSFORMERS
U
1. General Assembly,
2. Cable Box Drawing
4. Drawings Required 3. Terminal Bushing Drawing
4. Core and Winding Assembly Drawing
5. Foundation Drawing
6. Sample complying with the standard Sample is required after approval of the
To be submitted with the request Drawing (l No. 315KVA. and 1 No. 1000 KVA
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
65
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
01 Standard OES-5
Rating under
02 100/200/315/500/1 000 KVA
Oman Condition
Temperature Rise:-
04 - Oil 40 Deg. C
- Winding 50 Deg. C
Off-Circuit
+ 5% To - 5%
05 Tapping Locking
In Steps of 2.5%
Facilities
07 Impedance 4.75%
System Highest
08 12.5 KV
Voltage
Class - A
09 Winding Insulation
BS 2751
10
Tank Minimum
Thickness
Bottom 5MM
Sides 4MM
Top 5MM
Radiator/Fins 1.2 MM
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
66
SL
Items Requirement Submission Compliance
No.
11 Terminal
Arrangement
1 ) Pole Mounted
Transformer
Outdoor 440MM
Bushing
Creepage Aerofoil Open Profile
Insulator Shed
Clearances
Phase to
Phase
HV 270 MM
LV 150 MM
Terminals 50 SQ. M. M Copper
Suitable for conduct
for HV Side
4C X 185 SQ. M. M For
100 & 200 KVA TX
Two 4C X 185 SQ. MM For
315 KV A. TX on LV Side
2) Ground
Mounted
Transformer
Cable Box
Phase To
Phase 180 MM
HV 120 MM
LV HV 100 MM
Phase to Earth 4C X 50 SQ. M. M Side
HV 630 SQ. MM
Bushing 2 Single Core/Phase +
Terminal Neutral
Suitable for for 1000 KV A. TX. One
Cable Size Single
Core 630 Sqmm / Phase +
LV Neutral
For 500 KV A TX
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
67
SL
Items Requirement Submission Compliance
No.
Two Earthing
13 Required
Terminals
Fittings:-
1) Conservator
Required
Vessel
Complete with
Filling Cap and
Drain Valve
2) Lifting Lugs
Required
3) Oil Level Gauge
Required
4) Main Tank Drain
Required
Valve
5) Conservator To Main
Required
Tank Valve
14
6) Dial Type
Required
Thermometer
with Maximum
Reading Pointer
7) Thermometer
Required
Pocket
8) Rating Diagram Plates
Required
9) Silicagel
Breather
Required
Container
Vandal Proof
and Tansparen
15 Gaskets Cork or Similar Material as
Base
Bonded by Oil Resistance
Synthetic Material or Rubber
in
One Piece
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
68
SL
Items Requirement Submission Compliance
No.
Mounting of Silicagel
Breather
20 CM from the Bottom
16 in the Pole
Mounted
Transformer
Insulation of End
17 connection of Required
Winding
18 Required
Earthing of Core
Insulation Barner
21 To be Provided
between Windings
22 Sample Required
Test Certificate
23 from Independent Required
Authority
25
Performance
Checking through Required
Load Cycle
Note :- If any of the above Is not complied with, the product approval application will not be accepted,
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – MEW Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
69
11 KV RING MAIN UNIT
U
6. Sample complying with the standard Sample is required after approval of the
To be submitted with the request Drawing
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
70
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
General
01 OES - 11
Requirements
Two 3 Phase Ring Main
02 Assembly Switches 400 A and One 3
Phase Tee off Switch 150 A
Switches & Fuse
Assy. Oil Immersed
or SF6 Gas Insulation
and Current
03 Required
Interruption with
either H RC Fuses
in Air or SF6 Circuit
Breaker
04 Metal Clad
Degree of
05 Protection
IP 54
06 Extensible
Switches/Co B.
Position
07 - On
- Off/Earth off
- Earth
08 Pad Locking Required
09 Rated Voltage 11 KV
10 Highest System 12.5 KV
Voltage
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
71
SL
Items Requirement Submission Compliance
No.
Impulse Withstand
11 Voltage
75 KV
Power Frequency
12 Test
27 KV
Rated Normal
Current (Site
Rating) 400A
13 - Ring Main
Switch 150 A
- Tee off Switch/
Circuit Breaker
Fusing Rating of Tee
14 off Switch Fuse
63A
Rated Breaking
16 Current of Ring 400A
Main Switch
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
72
SL
Items Requirement Submission Compliance
No.
Operating and
19 As per OES 19
Interlocks
SF6 Switchgear:-
20 Pressure Gauge Less than 1% per Annum
Gas Leak
24 Sample Required
Note :- If any of the above Is not complied with. the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
73
11 KV CABLES
U
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
74
PRODUCT APPROVAL WORKING GROUP
U
11 KV CABLES
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
12.5 KV
Highest System
02 Voltage
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
75
SL
Items Requirement Submission Compliance
No.
Cross Sectional
Drawing of the To be submitted
Cable
Test Certificate
from Independent Required
Authority
Sample Required
Note :- If any of the above is not complied with, the product approval application will not be accepted,
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
76
11 KV LINE POST INSULATOR
U
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
77
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
Nominal System
02 Voltage
11 KV
System Highest
03 Voltage
12.5 KV
Minimu Dry
Impulse withstand
04 (Peak)
110 KV
Minimum Wet
05 Power Frequency 50 KV
Withstand
Mechanical
06 Failing Load 11 KV
07 Creepage 440MM
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
78
SL
Items Requirement Submission Compliance
No.
Fixing Stud:-
- Length CA) 54MM
10 - Length CB) 191 MM
- Thread CA) 39.7 MM
102 MM
- Thread CB)
dd dd
Test Certificate
13 from Independent Required
Authority
Required
Sample Produced
14
For Inspection
Note:- If any of the above Is not complied with, the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
79
11 KV STAY INSULATOR
U
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
80
PRODUCT APPROVAL WORKING GROUP
U
11 KV STAY INSULATOR
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
01 Standard BS 137
02 Material Glazed Porcelain
Performance Requirement:-
- Nominal 11 KV
System Voltage
- System Highest
Voltage 12.5 KV
03 - 50 Cycles Dry
Flashover 40 KV
- 50 Cycles Wet
Flashover 22 KV
- Leakage Distance
80MM
- Tensile Strength 90 KN
Smoothly Glazed Free from
04 Appearance
Defects and Blemishes
05 Co lour Brown/Chocolate
- Manufacturer's Name
06 Marking:- - Year of Manufacture
- Mechanical Failing Load
Test Certificate
07 from Independent Required
Authority
08 Sample Required
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
81
PART 111
L.T.
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
82
800 A/1600 A FEEDER PILLARS
U
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
83
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
01 Test Certificate
Short Circuit Test:-
02 - 46 KA for 0,3 Sec,
Double Leaf Opening 180
03 Doors Deg,
Degree of
04 Protection
IP 55
Required
09 Earthing Terminals
A) Incoming Unit
Rating
B) 3 C.T,'s 80011600 A Site Rating
C) Max, Demand 800/5 or
Indicators 1600/5 Class -1 Moulded
D) 1 KWH Meter Type
10 Three Potential
Circuit Fuses
E) Terminals for
Single Core 630
Sq, MM, XLPE Aluminum
F) Spacing between the 400MM
Termination and
Bottom Plate
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
84
SL
Items Requirement Submission Compliance
No.
Outgoing Ways No.
of Bays 6/8:-
- Glands with
Earth Tap and 45MM
Plastic Shroud
- Clearance
11 - Fuse Grip
Handle
- Phase Barriers Flame and arc resistance
- Spacing
Termination
and Bottom 450MM
Plate
Note :- If any of the above is not complied with, the product approval application will not be accepted,
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
85
400 A MINI FEEDER PILLAR
U
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
86
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
Degree of
04 Protection
IP 55
Door Operated
07 Internal Light
Required
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
87
SL
Items Requirement Submission Compliance
No.
Tinned Copper Ph: 25 X 10M
Busbar Material
11 MNVT25X l0 MM
and Size
Earth 25 X 10 MM
Spacing between
12 Termination and 400MM
Bottom Plate
Outgoing Ways:- 6 Ways Rated 100 Amps each
A) Glands with
Earth Tag and PVC 45MM
13 Shroud
B) Clearance To be Provided
between Fuse Ways
C) Fuse Grip Handle
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
88
400 A CUTOUT BOX
U
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
89
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
Test Certificate
01 from Independent Required
Laboratory
Single Door With
Brass or Gun Metal
02 Hinges and Pad
Required
Locking Arrangement
Degree of
03 Protection IP 55
06 Mounting Bracket
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
90
SL
Items Requirement Submission Compliance
No.
13 Barrier Required
Insulated Shield
between Front
14 Required
Door and Live
Contacts
Double
Compression Glad
18 Required
in Case of Top I
Entry
19 Painting Finish:-
A) Brush or Spray 100 Microns
Painting
B) Phosphate Treatment 1.2 Microns
- Phosphate Coating
- Prime Coats 20 - 25 Microns
- Finishing Coat
40 Microns
C) Epoxy Powder
Painting
20 Thickness 60 Microns
Guarantee for
21 Painting 5 Years
Note :- If any of the above Is not complied with. the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
91
CONSUMER UNIT
U
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
92
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
Size of Box:-
3 Phase 300MM
- Width 600MM
- Height 240MM
02 - Depth 350MM
Single Phase
- Width 400MM
- Height 200MM
- Depth
Locking Arrangement to be
Lock Arrangement Provided. Cylinder Type
05
Locking with Master Pad
Lock
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
93
SL
Items Requirement Submission Compliance
No.
Mounting
06 Holes at 4 Corners
Arrangement
IP 55
Degree of
07
Protection
Cutout:-
10 - Rating 100 A
Cartridge Paved TYPD
- Type of Fuse
11
Colour Grey
Note :- If any of the above is not complied with. the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
94
LT. SHACKLE INSULATOR
U
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
95
PRODUCT APPROVAL WORKING GROUP
U
SHACKLE INSULATOR
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
As per Drawing
02 Dimensions
No. MEWjOhj039 Rev. A
03 Dry Flashover 17 KV
Transverse
05 Strength
13 KN
Test Certificate
06 from Independent Required
Authority
07 Sample To be Submitted
Note :- If any of the above is not complied with. the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
96
LT. STAY INSULATOR
U
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
97
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
02 Dimensions
03 Tensile Strength 60 KN
04 Dry Flashover 25 KV
05 Wet Flashover 12 KV
Test Certificate
06 from Independent Required
Authority
07 Sample To be Submitted
08
Reference List Required
Note :. If any of the above Is not complied with, the product approval application will not be accepted,
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
98
L.V. CABLES
U
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
99
PRODUCT APPROVAL WORKING GROUP
U
L.V. CABLES
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
01 Standard BS 5467
Insulation Thickness
- 240 Sq. M 1.7 MM
- 185 Sq. M 1.6 MM
- 120 Sq. M 1.2 MM
04 - 70 Sq. M 1.1 MM
0.9 MM
- 35 Sq. M 0.9 MM
- 25 Sq. M 0.7 MM
- 16Sq. M
Sheat
Extruded PVC Type-9 Table
of BS 6746 Thickness as per
Thickness:-
Bs 5462
- 240 Sq. M
- 185 Sq. M
1.6 MM
05 - 120 Sq. M 1.4 MM
- 70 Sq. M 1.4 MM
- 35 Sq. M 1.2 MM
1.0 MM
- 25 Sq. M 0.8 MM
- 16 Sq. M
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
100
SL
Items Requirement Submission Compliance
No.
Single Galvanized Steel
Armour:-
Wires
to BS 1442 Aluminium
Armour
for Single Core Cables. dia.
of
06 - 16 Sq. M Wires
- 35 Sq. M 1.25 MM
- 70 Sq. M 1.6 MM
- 120 Sq. M 2.0 MM
2.5 MM
- 240 Sq. M
2.5 MM
Serving Extruded PVC Type - 9.
Thickness Table of
- 240 Sq. M BS 6746
2.7 MM
- 185 Sq. M
2.6 MM
07 - 120 Sq. M
2.3 MM
- 70 Sq. M 2.1 MM
- 35Sq. M 1.8 MM
- 25 Sq. M 1.7 MM
- 16 Sq. M 1.6 MM
Cross Section
08 Drawing of the To be Provided
Cable
Test Certificate
09 from Independent Required
Authority
11
Sample To be Submitted
Note :- If any of the above is not complied with. the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
101
XLPE COVERED ALUMINIUM CONDUCTOR
U
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
102
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
01 Standard BS 6485
02 Conductor
Details:-
- Section Area:
200Sq. MM 119.51
120 Sq. MM 73.51
70Sq. MM 37.10
35 Sq. MM
- Stranding/DIA
200Sq. MM 19/3.78
120 Sq. MM 19/2.83
70 Sq. MM 7/3.66
35 Sq. MM 7/2.6
- Overaii/DIA
200Sq. MM
120 Sq. MM 18.90 MM
70Sq. MM 14.21 MM
35 Sq. MM 10.97 MM
- Weight/KM 7.80 MM
(KGS)
200Sq. MM 587.00
120 Sq. MM 329.39
70 Sq. MM 202.77
35 Sq. MM 101.50
- Ultimate
Strength (KGS) 3240
200Sq. MM 1991.8
120 Sq. MM 1216.0
70Sq. MM 576.0
35 Sq. MM
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
103
SL
Items Requirement Submission Compliance
No.
Construction:~ Compacted
- Conductor Circular Stranded as per
- Covering BS 215 ~Part 1
Cretruded Black
Gross Linked
03 Polyethylene as per IES
- Minimum 502
Thickness (MM)
200Sq. MM 1.8
120 Sq. MM 1.6
70Sq. MM 1.4
35Sq. MM 1.2
600/1000V
Test Certificate
05 from Independent Required
Authority
06 Sample Required
07 Reference List
Required
Note:- If any of the above Is not complied with, the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
104
SINGLE PHASE/THREE PHASE KWH METERS
U
10. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
105
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
02 Performance:-
- Current 20-200 A
- Voltage
240/415 v
- Frequency 50 HZ
- Accuracy Class 2
- Max. Amb1ent 50 Deg. C
- Temperature
03 Construction Phenol Moulded Case
Integral Terminal Block
Magnetic Repulsion
Bearing
Five Digit/Six Digit Number
Register 1n White on a Black Back
Ground
04 Test Certificate Required
from International
recognized testing
Laboratory
05 Sample Required
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
106
PART IV
GENERAL
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
107
DISC INSULATOR
U
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
108
PRODUCT APPROVAL WORKING GROUP
U
DISC INSULATOR
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
01 Standard BS 137
03 Creepage 280 MM
04 Min. Mechanical
Failing Load 80 KN
05 Min. Electrical
Characteristics
- Power Frequency
Flashover
Dry 68 KV
Wet 50 KV
- Impulse Flashover
Positive 100 KV
Negative 100 KV
- Power Frequency
withstand Voltage 64 KV
Dry 45 KV
Wet 90 KV
- Impulse withstand
Voltage
- Power Frequency 120 KV
Puncture Voltage
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
109
SL
Items Requirement Submission Compliance
No.
Construction
06 Without Blemishes
Appearance
07 Cementing
08 Colour Brown/Chocolate
14 Sample To be Submitted
Note:- If any of the above 1s not complied with, the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
110
ACSR CONDUCTORS
U
Aluminum Wires
U
i) Tensile Test
ii) Wrapping Test
iii) Resistively Test
Steel Wires
U
9. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
111
PRODUCT APPROVAL WORKING GROUP
U
ACR CONDUCTOR
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
02 Conductor
Specification :- 261.2Sq" MM
- Area Panther 195.0 Sq" MM
Wolf 118.8 Sq" MM
Dog
- Standing AI/
Steel NO/DIA. NO/DIA.
Panther 30/3.00 7/3.00
Wolf 30/2"59 7/2 59
Dog 6/4.72 7/2.57
- Overall DIA.
(MM)
Panther 21 MM
Wolf 18.13 MM
Dog 14.50 MM
- Weight Per KM
(KGS) 976
Panther 727
Wolf 394
Dog
- Ultimate 9085 I
Strength (KGS) 727
Panther 3310
Wolf
Dog
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
112
SL
Items Requirement Submission Compliance
No.
Joints 1n Aluminum
Strands:- No Joints Permitted
05 - Outer Most Joints not less than 15 M
Layers Apart
- Inter Layer
06 Joints in Not Permitted
Galvanized Steel Wire
31 Microns
Dog (215 GM/Sq. M)
oxidization
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
113
TENSION CLAMP
10. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
114
PRODUCT APPROVAL WORKING GROUP
U
TENSION CLAMP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
Malleable Iron/ Aluminum
01 Material
Alloy
02 User Aluminum
03 Clamping Bolts 4
04 Dimensions
As per Drg. No. MEW/OH/004
Minimum Failing
05 Load
06 Galvanizing
Thickness 127 Microns
Connector:- Galvanized
- Material Malleable Iron
80 KN
07 - Failing Load As per Drawing
- Dimension 127 Microns
- Galvanizing
Ball Eye: Malleable iron
- Material 80 KN
08 As per Drawing
- Failing Load
- Dimens1ons
Test Certificate Required
09 from Independent
Authority
Required
10 Reference List
To be Submitted
11 Sample
Note:· If any of the above is not complied with, the product approval application will not be accepted.
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
115
STAY WIRE FOR OVERHEAD LINES
U
11. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
116
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
Diameter of Wire:-
01 Item- 1 3.25 MM
Item- 2 4.00 MM
02 No, of Strands 7
03 Standard BS 183
Specification Grade 1150
08
Note:- If any of the above is not complied with, the product approval application will not be accepted,
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – MEW Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
117
CABLE COVER TILES
U
12. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
118
PRODUCT APPROVAL WORKING GROUP
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
Polyethylene 1
01 Material
Recycled Polyethylene
03 Thickness 6 MM
04 Width 200 MM
Distance from 20 MM
09
Hole Centre to
Edge
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
119
WOOD POLES
U
Process
13. Documents to be submitted with the i) Check list signed and stamped by the
Approval request. Manufacturer
ii) Technical literature
iii) Installation & Operation manual if
applicable
iv) Drawings
v) Experience List
vi) Test Certificates
vii) Sample
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
120
PRODUCT APPROVAL WORKING GROUP
U
WOOD POLES
U
MANUFACTURER :
AGENT :
DATE :
SL
Items Requirement Submission Compliance
No.
01 Standard BS 1990
BS 913 Retention of
02 Creosoting
l40KGS/CU. M
03 Species Pinus Silvestre's/ Douglas fir
Inspection Agency
12 Required
Signature: Seal:
PRODUCT APPROVAL WORKING GROUP – DCRP Note :- If any of the above Is not complied with.
the product approval application will not be
accepted.
121