Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
TABLE OF CONTENTS
SL PARTICULARS PAGE
1 INTRODUCTION
2 STANDARDS
3 SCOPE OF SUPPLY
8 GENERAL REQUIREMENT
Page 1 of 13
UltraTech TECHNICAL SPECIFICATIONS Dept
TIKC Cell 1.1KV, XLPE/ PVC, Copper, Control Cables E, I & CPPs
1.0 INTRODUCTION
M/s Ultratech Cement Limited is under expansion of its cement
manufacturing capacity at various locations as below:
2.0 STANDARDS
All materials in cables shall comply with applicable provisions of the latest
editions of relevant Indian Standards, Indian Electricity Rules, Indian
Electricity Act and other applicable statutory provisions, rules and
regulations such as IEC, IEEE and other relevant International Standards.
Equipment meeting the requirements of IEC/ANSI or any other
internationally recognized standard which ensure a quality equal to or better
than as per the standards indicated below shall also be acceptable. When
the equipment conforms to any other standards, salient points of difference
between the standards adopted and those prescribed in this specification
shall be clearly brought out in the tender and a copy of the applicable
standards(s) in English language shall also be enclosed by the supplier with
the tender.
Unless otherwise specified, the design, manufacture and performance of all
the equipment and material provided under this specification shall generally
conform to the latest issues of the following standards:-
The design, manufacture and testing of the cables shall be carried out as
per the latest applicable Indian Standards, Indian Electricity Rules and
Code of Practices. However, for ready reference, some of the salient
Standards and Code of Practices are given below:
Page 2 of 13
UltraTech TECHNICAL SPECIFICATIONS Dept
TIKC Cell 1.1KV, XLPE/ PVC, Copper, Control Cables E, I & CPPs
Page 3 of 13
UltraTech TECHNICAL SPECIFICATIONS Dept
TIKC Cell 1.1KV, XLPE/ PVC, Copper, Control Cables E, I & CPPs
Page 4 of 13
UltraTech TECHNICAL SPECIFICATIONS Dept
TIKC Cell 1.1KV, XLPE/ PVC, Copper, Control Cables E, I & CPPs
Page 5 of 13
UltraTech TECHNICAL SPECIFICATIONS Dept
TIKC Cell 1.1KV, XLPE/ PVC, Copper, Control Cables E, I & CPPs
Page 6 of 13
UltraTech TECHNICAL SPECIFICATIONS Dept
TIKC Cell 1.1KV, XLPE/ PVC, Copper, Control Cables E, I & CPPs
of tests certificates shall be furnished. The tests reports on the cables shall be
got approved from the purchaser before dispatch of the cables.
The seller shall confirm the above items for following inspection and testing,
which may be witnessed by the purchaser's representatives. The seller shall also
confirm that the purchaser’s representatives will be allowed to inspect and test
any of the items at any manufacturing process / stage.
The tests on the cables that will be conducted by the supplier shall be mentioned
in the schedule of tests.
The purchaser reserves the right to witness all tests and the supplier shall
provide all facilities, to the purchaser in this regard and shall inform the
purchaser sufficiently in advance to enable the purchaser to depute his
representative to witness the same.
5.1 ROUTINE TEST on all the cable drums shall be as follows:
5.1.1 Conductor resistance test,
5.1.2 High voltage test,
5.1.3 Insulation resistance test,
The above test shall be as per relevant Indian/International standards. The test
method, condition of test and test requirement shall comply with those given
under the type tests. Apart from these conductor examination, check of
dimensions etc. shall also be carried out as routine tests.
5.2 The following TYPE TEST shall be conducted as per applicable
standards on PVC insulated cables:
5.2.1 Tensile test
5.2.2 Wrapping test
5.2.3 Conductor resistance
5.2.4 Dielectric power factor test
5.2.5 Test for thickness of insulation and sheath
5.2.6 Tensile strength and elongation test for insulation and sheath
5.2.7 Ageing test for insulation and sheath
5.2.8 Loss of mass tests for insulation and sheath
5.2.9 Shrinkage Test for Insulation and Sheath
5.2.10 Hot Deformation Test for Insulation and Sheath
5.2.11 Cold Bend Test (up to 6mm.sq.) size
5.2.12 Cold Impact Test for Insulation and Sheath
5.2.13 Heat Shock Test for Insulation and Sheath
5.2.14 Thermal Stability Test for Insulation and Sheath
5.2.15 Test for Bleeding and Blooming of pigments for HR-PVC
Insulation & Sheath
5.2.16 Fire Resistance Test
Page 7 of 13
UltraTech TECHNICAL SPECIFICATIONS Dept
TIKC Cell 1.1KV, XLPE/ PVC, Copper, Control Cables E, I & CPPs
Page 8 of 13
UltraTech TECHNICAL SPECIFICATIONS Dept
TIKC Cell 1.1KV, XLPE/ PVC, Copper, Control Cables E, I & CPPs
Page 9 of 13
UltraTech TECHNICAL SPECIFICATIONS Dept
TIKC Cell 1.1KV, XLPE/ PVC, Copper, Control Cables E, I & CPPs
Page 10 of 13
UltraTech TECHNICAL SPECIFICATIONS Dept
TIKC Cell 1.1KV, XLPE/ PVC, Copper, Control Cables E, I & CPPs
Page 11 of 13
UltraTech TECHNICAL SPECIFICATIONS Dept
TIKC Cell 1.1KV, XLPE/ PVC, Copper, Control Cables E, I & CPPs
Page 12 of 13
UltraTech TECHNICAL SPECIFICATIONS Dept
TIKC Cell 1.1KV, XLPE/ PVC, Copper, Control Cables E, I & CPPs
Page 13 of 13