Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Revision 11/26/13
2012-
Toyota
Camry
IMPORTANT
Before starting, compare items on your invoice with items received.
Carefully check through packaging material. If any item is missing,
*0000530186*
please call Crutchfield Technical Support at 1-800-955-9094.
Although reasonable attempts are made to verify the accuracy of the information contained in this MasterSheet, it is presented without
warranties or guarantees of any type due to the constantly changing nature of this type of information and running changes in vehicle
Inside... production. Any person or entity using this information does so at his or its own risk. If you find our instructions are different from your
vehicle, or if you have questions, do not continue with your installation. Contact our toll-free technical support for assistance.
Page
4 Receiver Installation
5 Corner Dash Speakers
6-7 Front Door Speakers
8-9 Rear Deck Speakers
10 Wire Splicing Guide
Phillips Small Flat Blade 10mm 12mm Panel Tool Drill & 1/8” Bit Wire Strippers
Screwdriver Screwdriver & Crimp Caps
Socket, Ratchet
& Extension
Tools Required
Clock Housing
Receiver/Climate
1-800-955-9094 Control Assembly
TECHNICAL SUPPORT
OEM Integration
This page addresses integrating aftermarket accessories such as
CD Changers, Auxiliary Input Adaptors, iPod Adaptors, etc., with a
R
4. Test operation of the adaptor and reassemble dash by reversing removal steps.
Input
Receiver Installation Ensure that the wiring adaptor received from Crutchfield
plugs into the vehicle’s connector. If the connector is
missing or incorrect, please call our Technical
Support Department at 1-800-955-9094.
A Standard DIN unit is shown. A Double-DIN
receiver may also be installed following these
same steps.
1-800-955-9094
TECHNICAL SUPPORT Copyright 2013 Crutchfield Corporation 4
053 0186 NOTES:
Please read first
Corner Dash Speakers • Instructions show factory size speakers or speakers
with adaptor brackets only. Cutting or fabrication (not
shown) will be required for other speaker sizes.
! IMPORTANT
No speaker wiring adaptor is available at this time from
Crutchfield for this speaker location. It will be necessary to FIGURE 1 FIGURE 2
splice wires in order to install an aftermarket speaker.
The dash speakers and the door woofers are wired together
at each dash speaker location. If dash speakers are
replaced, the input and output wires must be spliced
together in order for the woofers to operate.
1-800-955-9094
TECHNICAL SUPPORT
! IMPORTANT
No speaker adaptor bracket is available at this time for this FIGURE 2 FIGURE 3
location. A mounting bracket must be fabricated in order to “Sail” Panel
install an aftermarket speaker.
Power Options
It is possible that the replacement speakers do not have
screws supplied. It may be necessary to acquire mounting Switch Panel
hardware.
1-800-955-9094
TECHNICAL SUPPORT
! SAFETY CHECK
Check that wires do not interfere with window operation.
Test door lock and release operation.
1-800-955-9094
TECHNICAL SUPPORT
! IMPORTANT
It is possible that the replacement speakers do not have
screws supplied. It may be necessary to acquire mounting FIGURE 2
hardware.
Seat Side Bolster
1. Pull up rear seat bottom cushion to release
two (2) clips and remove cushion (Figure 1).
1-800-955-9094
TECHNICAL SUPPORT Copyright 2013 Crutchfield Corporation 8
053 0186
1-800-955-9094
! CAUTION:
Always be careful when drilling in a vehicle. WEAR EYE
! SAFETY CHECK
TECHNICAL SUPPORT
PROTECTION. Be aware of things such as wiring, windows, Make sure seats and seat belts are secured to
fuel lines and safety devices. Check drilling depth and manufacturer’s specifications.
location to avoid damage to vehicle appearance. Check third rear brake light connection and test operation.
Copyright 2013 Crutchfield Corporation 9
053 0186
Wire Splicing Guide These methods can be used to make wiring connections if no receiver or speaker wiring adaptor is available.
Factory harness is removed. Save New speaker wires are spliced into
CRIMP METHOD harness if it is to be reconnected in
the future by this method.
SOLDER METHOD factory wires behind harness.
1. Cut factory wires behind 2. Strip end of each 1. Carefully strip out a 1/2” 2. Twist wires from new
factory speaker harness. wire back 1/2”. section on each factory speaker to stripped
speaker wire behind the sections of factory wires
factory speaker harness. as shown making sure
polarity is correct.
Factory Wires
---
-- - ------
Negative Wires
Strip Out 1/2” New Wires
+
+
+ + + + + + + + + + + + +
Positive Wires
3. Twist each positive pair of 4. Squeeze middle of cap 3. Heat wires first with 4. Wrap wiring connections
wires together and insert for tight connection. soldering iron, then with electrical tape.
in crimp cap. Repeat touch solder to
step for negative wires. 5. Connect new wires to wires for solid 5. Connect new wires to
speaker with spade connections. speaker with spade
First
connectors. connectors.
Factory Wire ---
-- - --------
Last -- -- - - -- - - -- -
+
+
+ + + + + + + + + + + + + + + + + + + + +
+
++ +
+ ++
+++ + + + ++++
1-800-955-9094
TECHNICAL SUPPORT Copyright 2013 Crutchfield Corporation 10