Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Model : DWD-1211RT
DWD-1221RT
DWD-1223RT
JUL. 2005
Downloaded from www.Manualslib.com manuals search engine
DRUM WASHING MACHINE
SERVICE GUIDE
One of the famous washers in the globe which uses laundry falling energy.
TUB
WASH
DRUM
DRAIN LIFTER
MOTOR BLDC
3. INLET PARTS
•COLD : 3-WAY
- COLD, PREWASH, DRY
•COLD : 2-WAY
- COLD, PREWASH
6. DRY PARTS
5. DOOR부
•MAIN PCB
•FRONT PCB
•HARNESS
•NOISE FILTER
•POWER CORD : 15A
2. DRIVE PARTS
•BLDC MOTOR
•DRUM
•BEARING
•SPIDER/SHAFT
•TUB
•WEIGHT BALANCER
4. WASH HEATING
8. SUPPORTER
•BASE
•DAMPER AS : 3(70N)
3. INLET PARTS
1. CONTROLLER
•FRONT PCB
•NOISE FILTER 5. DOOR AS
•MAIN PCB
•GLASS
•HINGE
•DOOR LOCK S/W
•GASKET
8. SUPPORTER 7. DRAIN
TEMP. SENSOR
FAN
TEMP. FUSE
•LIFTER
•ROTOR
BLDC MOTOR
•STATOR
•SHAFT
•SPIDER
2. ROTATION
•DRUM
•TUB
•WEIGHT BALANCER
4. WASH HEATING
RAIN •WASH HEATER
RAIN MOTOR •THERMISTOR
ALVE HOUSING
OSE
1. PANEL TYPE 1
NO PARTS NAME
1 FRME DOOR O
2 DOOR WINDOW
3 DCD STICKER
4 PANEL LOWER
5 CABINET FRONT
6 PANEL LOWER
7 FRAME TOP F
8 FRAME TOP R
9 CABINET
10 PLATE TOP
11 CASE HANDLE
12 HANDLE CAP
13 BADGE
14 WINDOW DISPLAY
15 DECO. WINDOW
16 BUTTON DOOR UNLOCK
17 BUTTON FUNCTION
18 DECO. FUNCTION
19 PLATE DISPENSER
20 BUTTON POWER
21 BUTTON DIAL OUT
22
23 BUTTON DIAL IN
24
25
26 HANDLE CABINET
27 BASE UNDER
INLETBOX ASS'Y
PANEL F ASS'Y
PANEL 1 :20EA
PANEL 2: 17 EA
CABINET F ASS'Y : 19 EA
BASE U AS : 8 EA TUB AS : 29 EA
10
11
12
13
14
H29 HEATER WASH 3612801100 110V 1KW 12.1Ω6.1W/SQ SUS RW8TF 144℃ 1
15
16
17
18
19
1. SEQUENCE CHART
20
21
2) Balancer Spin
① Check after finishing washing step with wet laundry.
② Checking by using motor output data during 20 sec, 65 rpm.
③ The decided data is different depending on loading condition.
22
23
start / hold
water level is NO
less than safety level? drain
YES
YES
Door open
24
① Press the“TEMP”
. and“DRY”button simultaneously during processing.
② Under the Child Lock function, only power button is working.
③ During Child Lock function, CHL will be displayed on PCB.
④ In orden to unlock Child Lock mode, press "TEMP" and "DRY" simultaneously.
① If the checking time to reset point is below 1 min, the remaining drain time is 30 sec.
② If the checking time to reset point is over 1 min, the remaining drain time is 2 min.
③ If the checking time to reset point is over 10 min, OE singal will be appeared on PCB.
④ If the temperature is over 50 ℃, the water will be supplied to high water level, then the drain will start.
25
1. Testing Mode
PCB and other electronic parts will be tested without water supply whether they are normal or not.
1) Process : press power button --> press "SPIN" button 3 times with pressing "WASH" button --> 'L d' will be shown on LED --
> Whenever pressing "TEMP" button 1 time, below process will be occurred.
L C (Lock Closed) --> F ( Fan Motor) ---> H (Hot V/V) --> C (Cold V/V) ->
P (prewashing V/V) -> d ( dry V/V) -> bb (bubble) -> dr (drain motor) ->
L O(Lock S/W Open)
2) More details
① When turn on 'LOCK' singal, all process is conducting normaly.
② When working starts, the PCB displys all the sensor conditions.
③ In this case, BLDC Motor is not tested. In order to test it, select spin or rinse.
1) Process : after pressing "WASH", "RINSE", "SPIN" button simultaniously, press "POWER" button.
ALL LED On/Off 1 time --> L C (Lock Closed) ---> R (Motor right) --> L (Motor Left) --> F ( Fan Motor) ---> H
(Hot V/V) --> C (Cold V/V) --> b (pre-wash V/V)
--> d ( dry V/V) --> bb (bubble) --> h1 (HEATER WASH)--> h2(HEATER DRY) --> dr (DRAIN MOTOR On) --
>L O(Lock S/W Open)
2) More tails
① LED test can be done with all LED On.
② All sensor conditions will be shown on PCB during processing.
26
ERROR
ERROR CAUSE COUNTERPLAN
SINGAL
①inlet valve broken Change the Inlet-Valve
WATER ②drain motor working during water supply Change the Drain Motor
IE
INLET ERROR ③pressure switch disorderChange the Sensor Pressure
④PCB can not check water level Change the PCB
①drain motor out of order Change the Drain Motor
DRAIN ②inlet valve working during drain Change the Inlet-Valve
OE
ERROR ③pressure switch disorderChange the Sensor Pressure
④PCB can not check water level Change the PCB
UE UNBALANCE ERROR ①laundry unbalance rearrange the laundry
① door opened during processing Clode the Door
DOOR
LE ②LOCK S/W broken Change the LOCK SW
OPEN ERROR
③ PCB can not check door lockChange the PCB
①continuous water supplyChange the Inlet-Valve
E2 Overflow ②drain motor can not workChange the Drain Motor
③pressure switch disorderChange the Sensor Pressure
FAN MOTOR ① fan motor cannot work Change the Fan-Motor
E3
disorder ② PCB cannot control fan motor The contact of the Connector or Change the PCB
SENSOR PRESSURE
E9 ① abnormal water level Change the Sensor Pressure
ERROR
① huge noise re-installation
HIGH VOLTAGE
E5 ②spining with jamming clothes between gasket rearrange the laundry
ERROR
③PCB broken Change the PCB
① huge noise re-installation
②spining with jamming clothes between gasket rearrange the laundry
E6 EMG ERROR
③motor broken Change the Motor
④PCB broken Change the PCB
①move opposite direction
E7 Direction Error
②motor Hall IC broken check the connector and change
①connector problem The contact of the Connector
E8 motor disorder
②abnormal loading conditioncheck the loading condition and change
sensor temp. ①sensor temp broken Change the Sensor Temp.
H1
dry disorder ②connector problem The contact of the Connector
sensor temp. ①sensor temp. of washing broken Change the Sensor Temp.
H2
wash disorder ②connector problem The contact of the Connector
overheating ①fan motor cannot spin Change the Fan Motor
H3
dry heater ②sensor temp. of dry brokenChange the Sensor Temp.
overheating ①heater working with no water supply check water level
H4
wash heater ②sensor temp. of wash brokenChange the Sensor Temp.
H6 abnormal of washing heater ①washing heater cannot workChange the Heater Wash
H7 abnormal of drying heater ①dry heater cannot work Change the Heater Dry
abnormal of sensor temp.
H8 ①heater working with no water supply check the water level and washing heater
of washing
27
Model
NO PART NAME Rating (V/Hz) PART CODE BOM DESCRIPTION TYPE
WASH+DRY WASH
8 FUSE TEMPERATURE 15A 250V ◎ - 361A800100 128℃ DF 128s 15A 250V DF128s
10 HWATER WASH 110/50-60 ◎ ◎ 3612801100 110V 1KW 12.1Ω 4.3W/SQ SUS 1R1A03305 144℃ IR1A033005
11 HEATER DRY 110/50-60 ◎ - 3612801300 110V 1.2KW 23.0Ω 6.1W/SQ INCOLOY800 1R1A034001 IR1A034005
12 SWITCH THERMOSTAT 100-250V ◎ 3619046500 ON 120℃ OFF 150℃ 230V 15A VDE NT-103NA
UNIT MOTOR BLDC 36189L4000 3254D02000, 3114D02000, 310V, 250W 3254D02000,
13 UNIT STATOR BLDC A11 ◎ ◎ 36189L4800 Φ265X28H, 36SLOT, 25NESOR, 3254D02000 3114D02000
UNIT ROTOR BLDC 36189L4900 MAGNET24, SERRATION, 3114D02000
14 THERMISTOR WASH A11 ◎ ◎ 361AAAAB00 R25=11, 981㏀, R80=1, 704㏀ CWT-DEW-1C03-0
15 NTC THERMISTOR Dry ◎ - 361AAAAC00 R40=26, 065㏀, R90=4, 4278㏀ CWT-DEW-1C02-0
16 UNIT FAN MOTOR Dry ◎ - 36189L3Z00 ISM-77806DWWA 24V CW 8P 14W ISM-77806DWWA
17 FAN AS Dry ◎ 3611885700 Φ133x45L IMPELLER -
18 DRAIN MOTOR 100-130/50-60 ◎ ◎ 36196TAK00 SV-HJ7T20D 100-110V ST23(56.5) SV-HJ7T20D
19 DAMPER FRICTION 11kg A11 ◎ ◎ 361A700100 70N AKS ST=170-245 DL=197.5 -
20 DAMPER PIN 11kg A11 ◎ ◎ 361A700200 AKS D=14.5 -
28
PRE-COLD,
DR12AS PP X
SUS FILTER
PRE-COLD-DRY
DR12AS PP X
SUS FILTER
DL-DW01 3P-PCB,
- X
DN-DD01 BRACKET
Comply with PLUG-15A, 125V, CABLE:2. 0SQ VCTFK 2C
LP-70 PVC BSMI R31050 CNS3199, CNS10917 CABLE MARKING : R31050 VCTFK 300V 2C 2.00
- 2, CNS690 xxxx --LINETEK--“LF”
DBK-115DA HIPS X HOSE, CUSHION HOSE Φ4 L830(BL), UL1015AWG22 L230, MG621164(WH)
- - X KET 1806 DL CONN UL1015 AWG18:HEATER, UL1015 AWG22:AC LOAD, UL1007 AWG22:DC LOAD
- - X KET 1806 DL CONN UL1015 AWG18:HEATER, UL1015 AWG22:AC LOAD, UL1007 AWG22:DC LOAD
RING TERM, ST710489-3x2-ST710946-3
- - X -
UL1015 AWG18(AWG16) GREEN/YELLOW
FUSE 128℃ DF128S 15A/250V, TUBE SRGT(ID-Φ5)WH,
DF128s - VDE -
L/W UL1015 AWG18 105℃ 600V
PA66 25% GF V0, ,ICOW S/W(BI-M) 16A 125V,
DF PA66 IMQ CA02. 01619 BI-METAL, SOLEN0ID
SOLENOID 125V 130Ω, PTC HEATER
THERMAL THERMAL FUSE 167℃, TUBE AISI321(SUS321),
IR1A033005 SUS321 VDE 72709
FUSE, BRACKET Mg0 INSULATION, SEALANT EPOXY 120℃
TUBE INCOLOY800, INSULATION Mg0, GASKET SILICONE,
1 IR1A034005 INCOLOY800 VDE 62726 BRACKET
INSULATING BUSHING CERAMIC, SEALANT FPOXY 120℃
NT-103NA MP VDE 119277 - NT-103NA(5XV) F150-120, ±5℃
3254D02000, AS
3114D02000 STATOR X OUTER ROTOR
ROTOR
CWT-DEW-1C03-0 SUS X B25/100=3760K±2%
CWT-DEW-1C02-0 SUS X B25/85=3992K±2%, L/W UL1007 AWG24 L=120, MG621164(KET)
ISM-77806DWWA - X
- ALDC X -
SV-HJ7T20D X SIDE SPONGE
- - - DAMPER(70N)+PIN
- - - -
28
29
WASH VALVE(GREEN) :
COMMON(BLUE)/RESISTANCE TEST
PRE-WASH VALVE(RED) :
COMMON(BLUE)/RESISTANCE TEST
DRY VALVE(YELLOW) :
COMMON(BLUE)/RESISTANCE TEST
MAIN PCB "8P" WHITE
COMMON(BLUE)
CONNECTOR
30
PCB
TROUBLE SITUATION CAUSE CHECK POINT SOLUTION
ERROR MODE
continuously inlet valve is normal, bellows problem frequency Check : refer to below change the "E2"
water supply but continuous water pressure switch
supply hose problem frequency Check : refer to below change the hose "E2"
check the fine hole change the hose "E2"
"E9" clogged hose check the hose condition remove the alien "E2"
ERROR water level frequence connector slipped out check the connector condition reconnecting "E9"
below 15kHz or over pressure switch broken frequency Check : refer to below change the "E9"
30kHz pressure switch
connector short connector broken "E9"
Checking method of coil registance, harness, connector.
GROUND(GRAY)
INPUT SIGNAL(WHITE)
OUPUT SIGNAL
(PINK)
* E2 : overflow error ;Water level is higher than overflow level because of continuous water supply.
E9 : Pressure switch trouble, the frequency is less than 15kHz or more than 30kHz in the processing.
31
32
33
1) SPEC. OF HEATER
1. Temperature fuse
•If the heater is on without water, because of pressure switch trouble, fire can be occurred.
Temperature fuse prevents this hazard of fire.
•The heater wash must be submerged in water.
34
3P Connector 3P Connector
orange wire Red Wire
1P Connector 1P Connecor
Blue Wire Blue Wire
35
1. Disassemble Connector
4. Assemble in the reverse order. Be sure to assemble in the order : Nut for heater-Nut for EARTH.
* Structure of DUCT B As
1. Heater Dry
2. Diecasting DUCT
3. Thermistor Dry
4. FAN MOTOR
5. Fuse Temp.
6. Switch Bimetal
7. FAN
* ERROR MODE
1. "H1" : Thermistor Dry OPEN/SHORT
2. "H2" : Thermister Wash OPEN/SHORT
3. "H3" : Dry Overheating(Sensing Temp. is over 125℃)
4. "H4" : Wash Overheating(Sensing Temp. is over 95℃)
5. "H5" : Wash Overheating
(In Wool, Lingerie courses sensing temp. is over 45℃)
6. "H6" : Abnormal condition of Heater Wash
(when the temp. increase at 10 minutes after heater operation is under 10
℃)
7. "H7" : Abnormal condition of Heater Dry(when the temp. increase at 10 minutes
after heater operation is under 10℃)
8. "H8" : Heater Wash Overheating
(when the temp. increase within 30sec after heater operation is over 5℃
without water)
9. "E3" : FAN MOTOR Broken(no signal from HALL IC)
36
1) BLDC MOTOR
Rotor
Insulator
Core
Insulator
BLDC MOTOR의 구성
electromagnet
37
1) DRY SYSTEM
D E
F G J
C
B H
38
T : Thermistor
(CONTROL
DRY DUCT HEATER’ S
TEMPERATURE )
HEATER
T FAN MOTOR
WATER SUPPLY
DRUM CONDENSING
DUCT
DRAIN
HOUSING
While rotating DRUM, DRY HEATER applice heat to air and FAN blows it into DRUM evaporating water in the laundry.
・Evaporated water is sucked into CONDENSING DUCT, and condensed in DUCT contacting WATER SUPPLY (condensed water
is extracted through DRAIN HOUSING).
・Dry function is performed by continuous repetition of evaporating and condensing circulation as above.
DRYING PROCESS
건조진행구간
ZONE DRUM
INSIDE TEMPERATURE
온도
TEMP.
PRE예열
HEATING
OF DRUM
내부온도
ZONE
구간
시간
TIME
39
In order to check the drying temperature during process going on : --> press the
"DRY" button, the display shows as below.
UPPER LED:
남은시간
REMAIN TIME Temperature for DRY
분
LOWER LED:
Temperature for WASH
40
◈ HEATER DRY
Function : heating the air during dry
◎ FAILURE MODE : * "H7" - The air cannot be heated to 10℃ during 2 min.
◎ CHECKING METHOD : * Check the resistance of heater coil and replace with new one.
◈ Thermistor
Function : sensing the air temperature.
◎ FAILURE MODE : * The air cannot be heated even though water is supplied.
* "H1" - shot or cut-off
* "H3" - air temp. is reached over 150℃
◎ CHECKING METHOD : * Check the resistance of thermistor, replace with new one.
◈ FUSE TEMPERATURE
function : protecting from the fine hazard or overheating, if the temp., rises over 128℃, power supply will be cut-off.
◎ Pictures
FIXED BY
WASHER
+
SCREW
41
◎ SPEC ◎ PICTURE
ITEMS SPEC
RATING VOLTAGE 24V
MOTOR 3700±10%
RPM
DUCT FAN AS 1900±10%
ROTAING DIRECTION CW
42
function : steilization with radiating far- infra red, by means of ceremic coating.
increasing the dry efficiency and effecting sterilization by radiating far infra-red ray from ceramic particle coating on DUCT
B UPPER
◎ principle
pass
heated air ---------> emit far-infra red far-infra
coating area
---------------------> steilization
tub inside
43
cause) ☞ The laurdry amount is more than the recommendation capacity 7.0kg.
☞ Condensing cold water is not supplied.
☞ Clogging Bellows Duct results in poor air circulation.
checking method)
cause) ☞ The dry is done from bad spin performance because of unbalance.
☞ no spin was done before the dry had started.
44
HEATER
THERMISTOR
FUSE TEMPERATURE
45
part name checking results repair method disassemble process of Fan Motor
FAN MOTOR fan motor failure replace ① Disassemble the DUCT AS from DUCT B AS.
fan motor (SCREW 4 EA)
DUCT COVER AS
2.5mm L-wrench
46
1) DWD-E1211RT
DRY
COLD
PRE
L/CHECK
LOCK 1
LOCK 2
WF07
WF06 WF07 3:P/CORD(ˆ»)
4
WF02:D/LOCK WF01:LOAD
2
RELAY 4:W/HEATER(ˆ»)
8
WF03:HEATER
10
HOT
1
10
12
13
1
3 4
D/M
B/B
FRONT
1: ß D/HEATER
2: W/HEATER
PCB
3: ¥ P-CORD(COMMON)
MAIN PCB
Ha
Hb
Hc
5V
8
5
WF08:F/MOTOR
1
WF04:S/W POWER
GND
U
V
1:ˆ» WF05:REACTOR
WF06
U
V
GND1
GND2
Vdd1
Vdd2
L/F
2: ß 2: ß
7
12
10
1
WF10:SENSOR WF09:MOTOR
1
3: ¥ 1: ß
1
Ha
Hb
T2
T1
(RD) (WH) (WH) (BL) (RD) (WH) (WH) (WH) (WH)
RELAY
WF04
WF10
WF09
WF05-1 WF05
WF08
WF01
WF02-1 WF02
WF03
123 1 2 3 4 5 6 7 8 9 10 11 12 123 12 12345678 12345678 12 123 4 3
123 1 2 3 4 5 6 7 8 9 10 11 12 123 12 12345678 12345678 12 123 1 1
CON-RY
REC-RY
WF04-1
WF10-1
WF09-1
WF08-1
WF01-1
WF03-1
CON.04
AC POWER S/W
123 Hole 1. COMMON BL RD BR BR OR GN YW PK GY WH VT BK PK VT BL RD RD BK WH BL YW RD GY VT BR GN OR YW BL BK WH GY VT RD OR BR BL BL BL
123 Hole 2. NC
CON.040-S/W
Hole 3. NO
CON.050-RT
12
12
CON.050-RT
CON.010-VC
CON.010-VD
CON.010-VP
CON.RY-TM
COLD PRE DRY
Vdd1
CON.PC-P
REACTOR VALVE INLET 123
THERMOSTAT
(WH)
CON.PC-R
CON.080-FM
123
. ON : 110 – 5 C
. OFF : 150 – 5 C
16785234 9
(WH)
(WH)
CON.010-D/TH
CON.F01
CON.010-B/P
12 16785234 9 12
CON.080
(WH) 21
BK BL
YW
12 12
(DUCT» · :128 C)
21
GND
FUSE TEMPERATURE
CON.010
CON.010
(WH)
(WH)
Hc
(WH)
CON.010-W/TH
Signal
CON.010-SP(NA)
UVW
5V
12
GN/YW
123 YB WR YW 123
CON.020-D/L (WH)
321 WH BL
CON.RY-W/H
CON.090-M
(WH)
CON.F02
123
GND
WV U
Hb
Ha
2345
GN/YW RING.H
(WH)
CON.010-SH
HEATER WASH
HEATER DRY
(1200W)
(1000W)
PTC
Hb
PTC
Gnd
Bi-Metal
SOLENOID
ON 0.02s
Ha
CON.030-W/H
CON.030-D/H
Tm1 SENSOR Tm2 5V 12A 125V
WATER PRESSURE DRY FAN MOTOR(24V BLDC) BUBBLE PUMP MOTOR DRAIN S/W
SENSOR HALL DOOR LOCK
POWER CORD
RING.C3
RING.C1
RING.C2
MOTOR MAIN(BLDC)
~15A 125V
EARTH OUTER
E1211R (TAIWAN,JAPAN)
2) DWD-E1211WT
COLD
PRE
L/CHECK
LOCK 1
LOCK 2
WF07
WF02:D/LOCK WF01:LOAD
1
RELAY 4:W/HEATER(ˆ»)
5
WF03:HEATER
1
10
HOT
1
10
12
13
3 4
1
D/M
B/B
FRONT
1:
2: W/HEATER
PCB
3: ¥ P-CORD(COMMON)
U
V
GND1
GND2
Vdd1
Vdd2
L/F
2: ß 2: ß
9
7
12
10
1
WF10:SENSOR WF09:MOTOR
3
3: ¥ 1: ß
6
1
T1
WF10
WF09
WF05-1 WF05
WF01
WF02-1 WF02
WF03
REC-RY
WF04-1
WF10-1
WF09-1
WF01-1
WF03-1
CON.04
123 BL RD BR BR GN YW PK GY WH VT BK PK VT BL RD RD GN OR BL BK WH GY VT ß OR BR BL ˆ»BL BL
123
CON.040-S/W
CON.050-RT
12
12
CON.050-RT
ˆ»
CON.010-VC
CON.010-VP
AC POWER S/W
Hole 1. COMMON
Hole 2. NC
Hole 3. NO
COLD PRE
Vdd1
CON.PC-P
123
(WH)
CON.010-B/P
12 21
12 BK BL
21
GND
CON.010
(WH)
(WH)
CON.010-W/TH
Signal
CON.010-SP(NA)
12 UVW
GN/YW
123 YK WR 123
CON.020-D/L (WH)
321 WH BL
CON.RY-W/H
CON.090-M
(WH)
123
2345
GN/YW RING.H
(WH)
CON.010-SH
HEATER WASH
(1000W)
PTC
Hb
PTC
Gnd
Bi-Metal
SOLENOID
ON 0.02s
Ha
CON.030-W/H
RING.C2
MOTOR MAIN(BLDC)
~15A 125V
EARTH OUTER
E1211W (TAIWAN,JAPAN)
47
DRY
COLD
PRE
L/CHECK
LOCK 1
LOCK 2
WF07
WF06 WF07 3:P/CORD(ˆ»)
4
WF02:D/LOCK WF01:LOAD
2
RELAY 4:W/HEATER(ˆ»)
8
WF03:HEATER
10
HOT
1
10
12
13
1
3 4
D/M
B/B
FRONT
1: ß D/HEATER
2: W/HEATER
PCB
3: ¥ P-CORD(COMMON)
MAIN PCB
Ha
Hb
Hc
5V
8
5
WF08:F/MOTOR
1
WF04:S/W POWER
GND
U
V
1:ˆ» WF05:REACTOR
WF06
U
V
GND1
GND2
Vdd1
Vdd2
L/F
2: ß 2: ß
7
12
10
1
WF10:SENSOR WF09:MOTOR
1
3: ¥ 1: ß
1
Ha
Hb
T2
T1
(WH) (WH) (BL) (RD) (WH) (WH) (WH) (WH)
RELAY
WF10
WF09
WF05-1 WF05
WF08
WF01
WF02-1 WF02
WF03
1 2 3 4 5 6 7 8 9 10 11 12 123 12 12345678 12345678 12 123 4 3
1 2 3 4 5 6 7 8 9 10 11 12 123 12 12345678 12345678 12 123 1 1
CON-RY
REC-RY
WF10-1
WF09-1
WF08-1
WF01-1
WF03-1
BR OR GN YW PK GY WH VT BK PK VT BL RD RD BK WH BL YW RD GY VT BR GN OR YW BL BK WH GY VT RD OR BR BL BL BL
CON.050-RT
12
12
CON.050-RT
CON.010-VC
CON.010-VD
CON.010-VP
CON.RY-TM
COLD PRE DRY
Vdd1
CON.PC-P
REACTOR VALVE INLET 123
THERMOSTAT
(WH)
CON.PC-R
CON.080-FM
123
. ON : 110 –ß 5 ßC
. OFF : 150 –ß 5 ßC
16785234 9
(WH)
(WH)
CON.010-D/TH
CON.F01
CON.010-B/P
12 16785234 9 12
CON.080
(WH) 21
BK BL
YW
12 12
(DUCT» · :128 C)
21
GND
FUSE TEMPERATURE
CON.010
CON.010
(WH)
(WH)
Hc
(WH)
CON.010-W/TH
Signal
CON.010-SP(NA)
UVW
5V
12
GN/YW
123 YB WR YW 123
CON.020-D/L (WH)
321 WH BL
CON.RY-W/H
CON.090-M
(WH)
CON.F02
123
GND
WV U
Hb
Ha
2345
GN/YW RING.H
(WH)
CON.010-SH
HEATER WASH
HEATER DRY
(1200W)
(1000W)
PTC
Hb
PTC
Gnd
Bi-Metal
SOLENOID
ON 0.02s
Ha
CON.030-W/H
CON.030-D/H
Tm1 SENSOR Tm2 5V 12A 125V
WATER PRESSURE DRY FAN MOTOR(24V BLDC) BUBBLE PUMP MOTOR DRAIN S/W
SENSOR HALL DOOR LOCK
POWER CORD
RING.C3
RING.C1
RING.C2
MOTOR MAIN(BLDC)
~15A 125V
EARTH OUTER
E1213R (TAIWAN,JAPAN)
4) DWD-E1221WT / DWD-E1223WT
COLD
PRE
L/CHECK
LOCK 1
LOCK 2
WF07
WF02:D/LOCK WF01:LOAD
1
RELAY 4:W/HEATER(ˆ»)
5
WF03:HEATER
1
10
HOT
1
10
12
13
3 4
1
D/M
B/B
FRONT
1:
2: W/HEATER
PCB
3: ¥ P-CORD(COMMON)
U
V
GND1
GND2
Vdd1
Vdd2
L/F
2: ß 2: ß
9
7
12
10
1
WF10:SENSOR WF09:MOTOR
3
3: ¥ 1: ß
6
1T1
WF09
WF05-1 WF05
WF01
WF02-1 WF02
WF03
REC-RY
WF10-1
WF09-1
WF01-1
WF03-1
BR GN YW PK GY WH VT BK PK VT BL RD RD GN OR BL BK WH GY VT OR BR BL BL BL
CON.050-RT
12
12
CON.050-RT
ˆ»
CON.010-VC
CON.010-VP
COLD PRE
Vdd1
CON.PC-P
123
(WH)
CON.010-B/P
12 21
12 BK BL
21
GND
CON.010
(WH)
(WH)
CON.010-W/TH
Signal
CON.010-SP(NA)
12 UVW
GN/YW
123 YK WR 123
CON.020-D/L (WH)
321 WH BL
CON.RY-W/H
CON.090-M
(WH)
123
2345
GN/YW RING.H
(WH)
CON.010-SH
HEATER WASH
(1000W)
PTC
Hb
PTC
Gnd
Bi-Metal
SOLENOID
ON 0.02s
Ha
CON.030-W/H
RING.C2
MOTOR MAIN(BLDC)
~15A 125V
EARTH OUTER
E1213W (TAIWAN,JAPAN)
48
HOSE DRAIN I
HOUSING VALVE
DRAIN MOTOR
VALVE AIR AS
2. Operating Sequence
DRAIN MOTOR connects drain passage by pulling LINK VALVE DRAIN. If the DRAIN MOTOR stops working,
LINK VALVE DRAIN returns to initial state by spring.
3. Check point when connecting hose drain O
① Keep the hose straight.
② Keep the end of hose not to dip in water.
4. Checking Methods
◎ Situation : * "OE" is shown on PCB.
* Not finishing drain during 10 min.
* The water level can not reach to RESET POINT during 10 min of drain.
* Check the hose drain O condition; twisted or frozen. * replace HOSE DRAIN O
* clean the inside of COVER VALVE.
* Check the hose drain O condition, blocked.
disassemble COVER
VALVE by turning and
pulling
* replace DRAIN MOTOR
*DRAIN MOTOR is broken.
49
LEG ADJUST AS
FIXTURE
LEG
FOOT
2. INSTALLATION PROCESS
① Remove the FIXTURE UP/DOWN AS
CAP HOLDER
50
51
52
DWD-E1211RT/DWD-E1211WT
DWD-E1221RT/DWD-E1221WT
DWD-E1223RT/DWD-E1223WT
2005. 05