Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
59-1501-3
INSTALLATION INSTRUCTIONS
High Mount
Outdoor Detector N219
HX-40/40AM/
40DAM
CONTENTS
1 INSTALLATION PRECAUTIONS ............2
HX-40 2 PIRs standard model 1-1 BEFORE INSTALLATION ................2
HX-40AM HX-40 with anti-masking 1-2 PARTS IDENTIFICATION ................3
HX-40DAM HX-40AM with micro-wave 1-3 KNOCKOUTS ..................................4
• 3.0 m high mount detection area (12.0 m) 1-4 DETECTION AREA..........................5
1-5 DETERMINATION OF PIR
• Unique pyro element DETECTION LENGTH ....................5
2 INSTALLATION .......................................6
• Intelligent AND logic
2-1 MOUNTING WITH BRACKET .........6
• Dual signal processing logic 2-2 ADJUSTING THE VERTICAL
ANGLE.............................................8
• Vegetation sway analysis logic 2-3 MOUNTING WITHOUT
BRACKET ........................................9
• Ideal detection area setting 2-4 WIRING .........................................10
2-5 WALL TAMPER (OPTION) ............ 11
• Digital anti-masking (AM/DAM model only)
3 WALK TEST..........................................12
• Microwave range selector (DAM model only) 4 SETTING ..............................................13
5 AREA ADJUSTMENT ...........................16
6 LED INDICATION .................................17
7 SPECIFICATIONS ................................18
7-1 SPECIFICATIONS .........................18
7-2 DIMENSIONS ................................19
-1-
Downloaded from www.Manualslib.com manuals search engine
1 INSTALLATION PRECAUTIONS
2.5 m – 3.0 m
(8'2" – 9'10") Parallel Tilt
Consider the direction a person is approaching from, as well as the detection area.
Install the detector in a place where it is free from false alarm factors. For example:
• Sunlight and reflection • Heat source • Objects moving in the wind
-2-
Downloaded from www.Manualslib.com manuals search engine
HX-40
HX-40AM
-Precautions for installing two or more sensors HX-40DAM
Do not install two or more HX-40DAM’s units side-by-side or face-to-face. Instead, install them
back-to-back. If mounting on the same wall, be sure they are at least 1.0 m (3'3") apart from
each other.
Hood
PIR sensor
(Do not touch)
Screw (4 × 20 mm)
Microwave unit
(HX-40DAM only)
(Do not touch) Lens
LED indicator
Cover
Lock screw
Screw kit
For joint For wall mounting For hood
Screw (4 × 20 mm) Screw (4 × 20 mm) Screw (3 × 10 mm)
-3-
Downloaded from www.Manualslib.com manuals search engine
1-3 KNOCKOUTS
Wiring Hole
Wiring
knockout (Off-the-shelf) magnet switch
installation position
Wiring Hole
Do not touch
For wall For switch Up-Down
fastening box fastening lock screw
For bracket For wall fastening/bracket fastening
Adjustment screw For main unit fastening
Up-Down lock screw (installation pitch 83.5 mm (3.29"))
-4-
Downloaded from www.Manualslib.com manuals search engine
1-4 DETECTION AREA
Side view Top view
(Mounting height: 3.0 m (9'10"))
0' 10' 20' 30' 40'
40'
0' 10' 20' 30' 40' (ft.) (ft.)
(ft.) (m) 2 4 6 8 10 12
12.0 m
(ft.) 8 (m)
MW
10'
PIR 6
3.0 m
20'
40°
5'
30°
0' 4
20°
10'
2
(Mounting height: 2.5 m (8'2"))
10°
85°
0' 10' 20' 30' 40' (ft.) 0' 0
12.0 m 2
(ft.)
10' MW 10' PIR
PIR 4
2.5 m
5'
0' 20' 6
MW
• Vertical angle: 1 click (2.5°) upward
8
(Refer to “caution” in 2-2). (ft.) (m)
3.0 m (9'10")
3.0 m (9'10")
1 1 1
3
2 2
-5-
Downloaded from www.Manualslib.com manuals search engine
2 INSTALLATION
Use the bracket for normal installation. The unit may be mounted directly on the wall, without
the bracket, only if the following three conditions are not;
• The mounting height 3.0 m (9'10").
• Horizontal direction adjustment is unnecessary.
• The ground is level.
Caution>>
Do not change the detection
length with bracket.
Use the masking seal to
adjust the detection length.
90° 90°
20°
20°
Remove the Up-Down lock screw. Push the shaft cover clip straightforwardly with
1 2 your thumb. In case the clip is stuck, use a
suitable tool. e.g. back side of a screw driver.
Shaft cover
Shaft cover clip
Loosen the adjustment screw two turns. Tilt the bracket about 45° and pass
3 4 through the wire.
In
Adjustment screw Out
Caution>>
Do not loosen the
screw too much.
It may disassemble.
-6-
Downloaded from www.Manualslib.com manuals search engine
Determine the horizontal direction (left or Open the wiring knockout.
5 right) of the detector before installing the
6
bracket on the wall.
To the right To the left
Wiring knockout
Open the Up-Down lock screw knockout Tighten screws 1 and 2, adjust the bracket
7 for connecting the bracket.
8 angle (refer to 2-2), then tighten screw 3.
Perform an area check. If re-adjustment is
required, loosen screw 3 and change the
bracket angle.
After the adjustment is complete, tighten
screw 3 again.
In
Knockout with 4 × 20
tapping screw (screwkit)
Wiring
hole Wiring
sponge pad 14 × 20 screw
Out
34 × 35 Up-Down
lock screw
24 × 20 screw
Adjustment
screw
-7-
Downloaded from www.Manualslib.com manuals search engine
2-2 ADJUSTING THE VERTICAL ANGLE
For best performance, install detector parallel to the ground.
Decide the detection length. If you choose 9.0 m/5.5 m/4.0 m, mask the unnecessary lens with
masking seals. Refer to the 1-5 for the details.
12.0 m (40')
3.0 m (9'10")
if detector is parallel to the
ground.
Caution>>
If the base of the unit is already parallel to the ground,
• Do not change the detection length by tilting the unit up or down. Detection length should
be adjusted with masking seal. Refer to 1-5 and 2-1 for the details.
0°
Example (the ground is level) 2 clicks (5°)
4 clicks (10°)
0° is the right setting for 3.0 m
(9'10") height installation.
Adjust 1 click (2.5° upward) for 2.5 m
(8'2") height installation.
-8-
Downloaded from www.Manualslib.com manuals search engine
2-3 MOUNTING WITHOUT BRACKET
Open the wiring knockout with suitable Pull the wire through the base knockout.
1 tool e.g. screwdriver.
2
In
Out
Fasten the base to the wall. Install main unit after wiring to the
3 4 terminal.
-9-
Downloaded from www.Manualslib.com manuals search engine
2-4 WIRING
Power wires should not exceed the following lengths.
HX-40 HX-40AM HX-40DAM
WIRE GAUGE
12 V 14 V 12 V 14 V 12 V 14 V
160 m 360 m 140 m 310 m 120 m 250 m
AWG22 (0.33 mm2)
(520') (1,180') (460') (1,020') (390') (820')
260 m 560 m 230 m 490 m 180 m 390 m
AWG20 (0.52 mm2)
(850') (1,840') (750') (1,610') (590') (1,280')
410 m 900 m 360 m 780 m 290 m 630 m
AWG18 (0.83 mm2)
(1,350') (2,950') (1,180') (2,560') (950') (2,070')
AUX INPUT
(N.C.) *1
(N.C.)
(N.C.)
HX-40AM
HX-40DAM
HX-40
- 10 -
Downloaded from www.Manualslib.com manuals search engine
2-5 WALL TAMPER (OPTION)
Universal magnet switch may be mounted as a wall tamper.
Installation space for universal magnet switch is provided on the back of the main unit and the
bracket.
Maximum size of an applicable universal magnet switch: D 9 mm (0.35'') × W 40 mm (1.57'') × H 9
mm (0.35'').
Universal magnet switch on the market assist is not included.
Main unit Bracket
Wiring Hole
Magnet switch
(Bracket side)
Magnet switch (Wall side) installation position
Magnet switch (Wall side) installation position
installation position
-Installation
Install the universal magnet switch (wall Open the wiring knockout with suitable
1 side) to the wall. To determine the install
2 tool e.g. screwdriver.
position, use the “Install position template”
provided on the inside cover of the product
package.
Install the other portion of the universal magnet switch to the back of the main unit or the
3 bracket. Pull the wiring through the knockouts.
When not using the bracket
1 Fix
2 In
- 11 -
Downloaded from www.Manualslib.com manuals search engine
When using the bracket
1 Fix In
4
In
2
Tilt the bracket about 45° and
pass through the wire.
6
In 3 Wiring 5
Out Out
sponge pad
Magnet
switch
Install the bracket and the main unit to Connect the universal magnet switch wiring
4 the wall surface.
5 to the tamper terminal of the main unit.
3 WALK TEST
Set the DIP switch 1 (LED ON/OFF) to Check that the detector detects an
1 “ON”.
2 object in the intended detection area.
The installation has been successful if
the LED lights for two seconds after a
person walks into the detection area.
Detected
Not detected
Note>>
The switch is set “ON” by factory
default.
Note>>
For the walk test, move more than 1.0 m
(3'3") away from the detector.
- 12 -
Downloaded from www.Manualslib.com manuals search engine
4 SETTING
Do not touch
HI
STD Anti masking
OFF
sensitibity
selector
Do not touch
PIR sensitivity selector
HX-40
HX-40AM
-LED ON/OFF DIP switch 1 HX-40DAM
POSITION FUNCTION
ON
The LED lights when someone is
(Factory
detected.
default)
The LED does not light even if
OFF
someone is detected.
OFF ON
HX-40
HX-40AM
-PIR IMMUNITY DIP switch 2 HX-40DAM
POSITION FUNCTION
STD
(Factory PIR IMMUNITY logic is not activated.
default)
PIR IMMUNITY logic is activated. Use
IMMUNITY this under harsh environment (e.g.
small animal).
STD IMMUNITY
- 13 -
Downloaded from www.Manualslib.com manuals search engine
HX-40
HX-40AM
-AUX INPUT DIP switch 3 HX-40DAM
By connecting a satellite unit (another warning sensor), you can extend the detection area
and correct false alarms. As a satellite unit, you can use any general no-voltage contact
output (NC) warning sensor, including the following.
<Infrared (AIR) sensors, thermal line (PIR) sensors, universal magnet switches, etc.>
POSITION FUNCTION
AND When both the main unit and the satellite detect someone, the
(Factory alarm is output.
default) Set to this when not connecting a satellite unit.
POSITION FUNCTION
ON
Anti-masking signal is output from TROUBLE OUTPUT
(Factory
terminal.
default)
Anti-masking signal is output from both TROUBLE and
OFF
ALARM OUTPUT terminal.
Note>>
OFF ON Use this when not wiring a detected trouble input terminal on the control
panel.
HX-40
HX-40AM
-MICROWAVE IMMUNITY DIP switch 5 HX-40DAM
POSITION FUNCTION
STD
(Factory MICRO WAVE IMMUNITY logic is not activated.
default)
MICRO WAVE IMMUNITY logic is activated. Use this
IMMUNITY
under harsh environment (e.g. vegetation sway).
STD IMMUNITY
- 14 -
Downloaded from www.Manualslib.com manuals search engine
RANGE SELECTOR/ HX-40
SENSITIVITY HX-40AM
-MW RANGE SELECTOR/MW SENSITIVITY ADJUSTMENT ADJUSTMENT HX-40DAM
LONG MID
12.0 m M
(40') 0
SHORT
PIR
LONG
L H
MW
Factory default
1 SHORT HIGH
9.0 m M
SHORT
(29'6'') 0
PIR
L H
MW LONG
1 SHORT MID
5.5 m M
(18'1'') 2 SHORT
0
PIR
MW
LONG
L H
1
SHORT LOW
4.0 m 3 M
(13'1'') 2 0
SHORT
PIR
MW
L H
LONG
- 15 -
Downloaded from www.Manualslib.com manuals search engine
HX-40
PIR
HX-40AM
-PIR SENSITIVITY SENSITIVITY SELECTOR HX-40DAM
POSITION FUNCTION
HIGH
HIGH High sensitivity
MIDDLE
MIDDLE Middle sensitivity
(Factory default)
POSITION FUNCTION
HIGH High sensitivity
HIGH STD
Standard sensitivity
(Factory default)
STD OFF Disabled
OFF Caution>>
When closing the cover, do not leave any object within
1 meter from the unit.
5 AREA ADJUSTMENT
-DETECTION LENGTH ADJUSTMENT
To limit the detection length, apply the appropriate masking seal. Note that there are three
different types of seal.
9.0 m (29'6") 5.5 m (18'1") 4.0 m (13'1")
3.0 m (9'10")
3.0 m (9'10")
3.0 m (9'10")
1 1 1
3
2 2
-AREA MASKING
Pasting on example for
1 masking No. 5 and No. 6
3
1
2 Area masking seal
3 4
4
5 0 5 56
6
7
8 6
9
7
- 16 -
Downloaded from www.Manualslib.com manuals search engine
6 LED INDICATION
Red
Warm-up
Blinks for approx. 60 sec.
Alarm
Lights for 2 sec.
Anti-Masking
booting
(Anti-Masking
start up) Blinks 2 times and goes off for 5 sec. and then repeats for 180 sec.
Trouble
output
Masking detection
Blinks 3 times and goes off for 3 sec. and then repeats.
-HX-40DAM
DETECTOR CONDITION LED INDICATOR
Warm-up
Blinks for approx. 60 sec.
Alarm
Red lights for 2 sec.
PIR detection
Green lights for 2 sec.
MW detection
Yellow lights for 2 sec.
Anti-Masking
booting
(Anti-Masking
Green and Red blink 2 times simultaneously and go off for
start up)
Trouble 5 sec. This sequence is repeated for 180 sec.
output
Masking detection
Green and Red blink 3 times simultaneously and go off for
3 sec. This sequence is repeated.
- 17 -
Downloaded from www.Manualslib.com manuals search engine
7 SPECIFICATIONS
7-1 SPECIFICATIONS
Model HX-40 HX-40AM HX-40DAM
Detection method Passive infrared Passive infrared & Microwave
- 18 -
Downloaded from www.Manualslib.com manuals search engine
7-2 DIMENSIONS
Using bracket and hood Without bracket and hood
197.5 (7.78)
205 (8.07)
Unit: mm (inch) Unit: mm (inch)
- 19 -
Downloaded from www.Manualslib.com manuals search engine
NOTE
The following statement will be provided with the equipment as required by Article 6.3 of the
R&TTE Directive, 1999/5/EC.
The Optex HX series are in conformity with all essential requirements of the R&TTE Directive
(1999/5/EC). This equipment has been assessed to the following standards:
EN 300 440-1: 2009
EN 50130-4: 2004 including amendment 2: 2003
EN 60950-1: 2006+A11: 2009
This product is marked with which signifies conformity with Class II product
requirements specified in the R&TTE Directive.
The following table indicates the areas of intended use of the equipment and any known
restrictions. For countries not included in this list, please consult the responsible Spectrum
Management Agency.
The HX-40 series is only a part of a complete system, therefore we cannot accept complete
responsibility for any damages or other consequences resulting from an intrusion.
OPTEX CO., LTD. (JAPAN) OPTEX INCORPORATED (USA) OPTEX SECURITY Sp. z o. o. (POLAND)
TEL:+1-909-993-5770 TEL:+48-22-598-06-55
(ISO 9001 Certified)
Tech:(800)966-7839 URL:http://www.optex.com.pl/
(ISO 14001 Certified) URL:http://www.optexamerica.com/
5-8-12 Ogoto Otsu
Shiga 520-0101 OPTEX (EUROPE) LTD. (UK) OPTEX KOREA CO., LTD. (KOREA)
JAPAN TEL:+44-1628-631000 TEL:+82-2-719-5971
URL:http://www.optexeurope.com/ URL:http://www.optexkorea.com/
TEL:+81-77-579-8670
FAX:+81-77-579-8190
URL:http://www.optex.co.jp/e/ OPTEX SECURITY SAS (FRANCE) OPTEX (DONGGUAN) CO., LTD.
TEL:+33-437-55-50-50 SHENZHEN OFFICE (CHINA)
URL:http://www.optex-security.com/ TEL:+86-755-33302950
URL:http://www.optexchina.com/
- 20 -
Downloaded from www.Manualslib.com manuals search engine