Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
General information
Designation
INCO Inc., Proprietary Alloy: "NIMONIC PK33"
Typical uses
Aerospace, high temperature applications
Composition overview
Compositional summary
Ni48-63 / Cr16-20 / Co12-16 / Mo6-8 / Ti1.5-3 / Al1.7-2.5 / Other0.057 (impurities: Fe<1, Mn<0.5, Si<0.5, Cu<0.2, C<0.07,
Zr<0.06, S<0.015, B<0.005)
Price
Price * 24,2 - 30,3 USD/kg
Price per unit volume * 1,96e5 - 2,51e5 USD/m^3
Physical properties
Mechanical properties
Young's modulus 215 - 230 GPa
Specific stiffness 26,2 - 28,1 MN.m/kg
Yield strength (ela stic limit) 700 - 870 MPa
Tensile strength 1,05e3 - 1,3e3 MPa
Specific strength 85,3 - 106 kN.m/kg
Elongation 24 - 36 % strain
Compressive strength * 700 - 870 MPa
Flexural modulus * 215 - 230 GPa
Flexural strength (modulus of rupture) * 700 - 870 MPa
Shear modulus * 80 - 90 GPa
Bulk modulus * 160 - 195 GPa
Poisson's ratio * 0,28 - 0,3
Shape factor 21
Hardness - Vickers * 320 - 440 HV
Hardness - Rockwell B * 107 - 115 HRB
Hardness - Rockwell C * 32 - 45 HRC
Hardness - Brinell * 303 - 415 HB
Elastic stored energy (springs) 1,11e3 - 1,69e3 kJ/m^3
Fatigue strength at 10^7 cycles * 420 - 650 MPa
Fatigue strength model (stress range) * 390 - 700 MPa
Parámetros: Stress Ratio = -1, Number of Cycles = 1e7cycles
Fatigue strength model
1500
(stress range) (MPa)
1000
500
Thermal properties
Melting point * 1,3e3 - 1,38e3 °C
Maximum service temperature * 867 - 1,1e3 °C
Minimum service temperature -273 °C
Thermal conductivity 10 - 12 W/m.°C
Specific heat capacity 400 - 440 J/kg.°C
Thermal expansion coefficient 10,5 - 12,5 µstrain/°C
Thermal shock resistance 266 - 352 °C
Thermal distortion resistance * 0,845 - 1,08 MW/m
Latent heat of fusion * 275 - 300 kJ/kg
Electrical properties
Electrical resistivity 120 - 132 µohm.cm
Electrical conductivity 1,31 - 1,44 %IACS
Galvanic potential * -0,07 - 0,01 V
Magnetic properties
Magnetic type Non-magnetic
Processing properties
Metal casting Unsuitable
Metal cold forming Acceptable
Metal hot forming Acceptable
Metal press forming Acceptable
Metal deep drawing Limited use
Machining speed 3,66 m/min
Weldability Good
Notes Preheating is not required, post weld heat treatment is required
Durability
Water (fresh) Excellent
Notes
Warning
All nickel compounds should be regarded as toxic. Some can cause cancer and/or fetal abnormalities.
Other notes
NIMONIC is a registered trademark of the INCO group of companies.
As of September 1999 , INCONEL, INCOLOY, MONEL, NIMONIC, INCO-WELD, NILO, BRIGHTRAY, CORRONEL and
UDIMET have become registered trademarks of Special Metals Corporation
Keywords
X 8 NICOCRTI55-20-20, German manufacture (GERMANY)
EMVAC 90, Eletrometal SA Metals Especials (BRAZIL)
Enlaces
ProcessUniverse
Producers
Reference
Shape