Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
WASHING
Off
Short cycles 30°/30min 95°
Duration
Spin E60° Cottons/
1200 Lid
Drain 60° Coloured
900 Pre- /Main-wash Starch E40°
700 Rinses Rinse 40°
500 Drain Soak 30°
without Spin cold
Spin Pre- Rinse Extra- Delayed Start Wool cold
End
wash Short hold rinse start Pause 30° 60° Synthe-
Drum in position
40° tics
E40°
Filter Delicates 40°
30° Easy iron
40° cold
Washing machines,
Toploader
DGS-TDS-N
Edition 05.06
CONTENTS
Display .......................................................................................................................... 4
Electronic-Test .............................................................................................................. 43 - 44
Program ........................................................................................................................ 49 - 58
Change ........................................................................................................................ 59
DGS-TDS-N 05.06 R.B. © Electrolux -2- 599 51 82 75 EN
Control Panel
Version 1 (SIGMA-design)
Off
Short cycles 30°/30min 95°
Duration
Spin E60° Cottons/
1200 Lid
Drain 60° Coloured
900 Pre- /Main-wash Starch E40°
700 Rinses Rinse 40°
500 Drain Soak 30°
without Spin cold
Spin Pre- Rinse Extra- Delayed Start Wool cold
End
wash Short hold rinse start Pause 30° 60° Synthe-
Drum in position
40° E40° tics
Filter Delicates 40°
30° Easy iron
40° cold
J I H G F ED C B A
Version 2 (JEWELS-design)
Duration
1200 Lid
Off
Short cycles 30°/30min Prewash
Cottons/ 900
Normal spin Coloured 700 Mainwash
95°
Drain E60° 500 Rinses
60° Drain
Starch without
E40°
Rinse Pre- Spin Short Extra- Night Delayed Start Spin
40° wash rinse Cycles Stain start Pause
Soak 30° End
K J I H G F E DC B A
A Programcycle H Short
B Start, Pause I Spin speed
C Display of residual running time, fault codes J Prewash
D Delayed start 0', 30', 60', 90', 2h till 23h K Programselector
E Stain
F Night cycle
G Extra rinse
Display
Function:
- delayed start selection with the delayed start button
- cycle duration and remaining time indicated in hours and minutes, (e.g. 2h08min)
- extension of soak time by pressing the delayed start button
- information on error codes (e.g. E10)
Standby
Function:
- After 10 minutes of standby in the pre-selection position or at the end of the cycle, the light of the
Display switches off and the LED Start/Pause flashes slowly.
Pressing any button or rotating the selector, the appliance returns to the normal status.
Version 3 (CLUB-design)
Drain
Rinse
Sport
Spinning Pre- Extra- Delay
Speed wash rinse start
Wool Cold
Synthetic
Night Extra Easy Start
cycle Quick Iron Pause
Delicates
Cold Easy iron
J I H G F E D C B A
Multifunktionsdisplay LCD
D C B A
Standby
Function:
- After 10 minutes of standby in the pre-selection position or at the end of the cycle, the light of the
LCD switches off and the LED Start/Pause flashes slowly.
Pressing any button or rotating the selector, the appliance returns to the normal status.
The selection of the options is to be carried out after switching on the appliance and setting the desired
programme with the selector and before pressing the start/pause button.
Options
Gentle spin
Night cycle
Extra rinse
Rinse-hold
Pre-wash
Easy iron
Economy
Sensitive
Half-load
Intensiv
no spin
Bleach
Stains
Quick
Soak
Daily
90°C X X X X X X X X X X X X X X X X X
60°C X X X X X X X X X X X X X X X X X
50°C X X X X X X X X X X X X X X X X X
Cotton
40°C X X X X X X X X X X X X X X X X X
30°C X X X X X X X X X X X X X X X
Cold X X X X X X X X X X X X X X X
60°C X X X X X X X X X X X X X X X
50°C X X X X X X X X X X X X X X X
Synthetic 40°C X X X X X X X X X X X X X X X
30°C X X X X X X X X X X X X X
Cold X X X X X X X X X X X X X
Sport 30°C X X X X
40°C X X X X X X X X X
Compatibility with programmes
Delicates 30°C X X X X X X X X
Cold X X X X X X X X
Silk 30°C X X X X X
40°C X X X X
Wool 30°C X X X X
Cold X X X X
40°C X X X X X X X X
Mix 30°C X X X X X X X X
Cold X X X X X X X X
40°C X X X X X X X
Shoes 30°C X X X X X X X
Cold X X X X X X X
60°C X X X X X X X
50°C X X X X X X X
Jeans 40°C X X X X X X X
30°C X X X X X X X
Cold X X X X X X X
60°C X X X X X X
Short A
40°C X X X X X X
Soak
Rinses X X X X X X X X
Conditioner X X X X X
Drain
Spin X
Rinse hold X X X X X X X X X X X X X X
Night cycle X X X X X X X X X X X X
Pre-wash X X X X X X X X X X X X
Compatibility with options
Soak X X X X X X X X X X X X
Stains X X X X X X X X X X X X
Intensive X X X X X X X X X X X X
Daily X X X X X X X X X X X X
Quick X X X X X X X X X X X X
Econamy X X X X X X X X X X X X
Sensitive X X X X X X X X X X X X X X
Extra rinse X X X X X X X X X X X X X X X
Bleach X X X X X X X X X X X X
Half-load X X X X X X X X X X X X X X X
Easy iron X X X X X X X X X X X X X X
Reduced spin speed X X X X X X X X X X X X X
No spin X X X X X X X X X X X X X
Pre-selection X X X X X X X X X X X X X X X X X
Phases in
Pre-wash X X X X X X X X X X X X X X X
w hich
Wash X X X X X X X X X X X X X X X
selection is
possible Rinses X X X X
Spin X X X
Function:
- Hold the “delayed start” button pressed, the start time will be indicated in the display and counted
up, the start time can be selected max. from 0h, 30', 60', 90', 2h - 23 h.
- The start time is counted down hour by hour.
- Change of delayed start: - press the start/pause button
- enter a new time with the delayed start button
- press again the start/pause button
Start/ Pause button
Function:
- The selected program is activated by pressing the start/pause button.
The LED start/pause lights.
- If the cycle is to be paused, press the start/pause button.
Start/ Pause-LED blinks. The program interrupt.
- This is not possible after a program run time of 10 min.
LED status process
ON cycle is running (lid closed)
start/pause FLASHING cycle in pause position
OFF lid not closed
ON lid can be opened, it is possible to pause the cycle
lid (rot) FLASHING cycle was paused
OFF cycle running, no possibility to pause
Stains button
Function:
- This is available in the programmes cotton/coloured and synthetic fabrics.
The selected temperature however must be >=40°C.
- Separate rinsing in of stain remover through the pre-wash chamber, approx. 1.2 ltrs.
- Cannot be combined with the “pre-wash” button.
- Can't be combined with the program “cotton/coloured 30°C and cold”.
- Can't be combined with the program “synthetics 30°C and cold”.
- Extends the cycle duration in the main wash by 5 minutes after the first heating to 40°C.
Night Cycle-Button
Function:
- This button is effective in the cycles cotton/coloured wash, synthetics, delicate, wool fabrics and
short cycle 30°/30min.
- The number of rinces are increase cotton/cotoured from three rinces to six rinces and synthetic
from three rinces to four rinces.
- All rinces are without a spinphase.
- The programm is stopped in a rinse hold.
- In order to continue a program afterwards, you first have to select a separate draining or spinning.
- Switches off the buzzer ( if configured)
Extra rinse-Button
Function:
- This button is effective in the cycles cotton/coloured wash, synthetics and delicate fabrics.
- Two additional rinse cycles are added.
- No intermediate rinse, except after the last rinse cycle.
Function:
- This button is effective in the cycles cotton/coloured wash, synthetics and delicate fabrics.
- The program time are reduces.
- Two rinse cycles are performed with a reduced run time but an increased water level.
- Can't be combined with the cycles.cotton/colored E60°C / E40°C.
Function:
- By pressing this key, you can reduce spin-dry speed step by step down to zero or to rinse hold.
- Reduces the spinning speed of all spin-dry cycles.
1200 900 700 500 without spin
1000 900 700 500 without spin
Pre-Wash Button
Function:
- This is available in the programmes cotton/coloured, synthetics and delicate fabrics.
- Can't be combined with the program “wool”.
- It is heated up to max. 30 ° C.
- Can't be combined with the “bleach” button.
Rince hold-Button
Function:
- This button is effective in the cycles cotton/coloured wash, synthetics, delicate, wool fabrics and
short cycle 30°/30min.
- The program is finish with water in the drum.
Temperature button
Function:
- By pushing this button the washing temperature can be reduced to 0°C step-by-step.
adjust 90°C 60°C 40°C 30°C cold
temperature 90°C 60°C 50°C 40°C 30°C
Function:
With cotton/coloureds programmes:
Function:
- The cycle has a max. running period of 30min at 30°C drain temperature.
- The cycle includes a main cycle, two rinse cycles with a terminating final spin cycle.
Soak Button
Function:
- This can be done in the cycles cotton/coloured wash, synthetics and delicate fabrics.
- The soaking period begins with pre-wash and soaks for about the next 31 minutes.
- It is heated up to 30 °C.
- Cannot be combined with the Pre-wash button.
- You can prolong soaking time for max. 0h, 30', 60', 90', 2h - 10 h using the „Start preset“ key.
- After pressing the start key, the duration of the cycle is displayed by hours and minutes.
Jeans 40°
Function:
- The cycle includes a main cycle, five rinse cycles with a terminating final spin cycle.
- It is heated up to 40 °C.
- Can be combined with the Night Cycle Pre-wash and Spin deselection button.
Shoes 40°
Function:
- The program consists of main wash, three rinse cycles without interim spinning but with final
spinning.
- It is heated up to 40 °C.
- Can be comdined with the Quick, Extra rinse, Night Cycle, Pre-wash, Soaking and Spin
deselection button.
Function:
- Wash temperature is reduced to 60°C and wash time is prolonged.
- Can't be combined with the quick function.
Short A
Function:
- There are two short programs A.
40°C / 40min : The program lasts 60min and the wash temperature is 40°C.
60°C / 60min : The program lasts 60min and the wash temperature is 60°C.
- The program consists of a main wash, two rinses with higher water levels intermediate and
end spin.
- The load amount is 3Kg.
Silk 30°
Function:
- The program consists of a main wash, three rinses without intermediate spins but with an end spin.
Rinses
Modification of rinses acording to the options selected.
Super rinse
Super rinse
Night cycle
Easy Iron
Sensitive
Normal
Extra quick 2 3 4 5 6 - -
Quick 3 4 5 6 7 - -
Cotton Eco 3 4 5 6 7 - -
Eco 2 3 4 5 6 - -
Normal 3 4 5 6 7 - -
Extra quick 2 3 3 3 5 - -
Programmes
Synthetic Eco 3 4 4 4 5 - -
Normal 3 4 4 4 5 - -
Extra quick 2 - 3 - - - -
Delicates
Normal 3 - 4 - - - -
Wool Normal 3 - - - - - -
Hand-wash Normal 3 - - - - - -
Silk Normal 3 4 5 4 5 - -
Short A Normal 2 - 4 - 7 5 5
Jeans Normal 5 6 - - - 5 8
Shoes Normal 3 - 5 - - - 3
The option HALF LOAD, reduces of one rinse all the programmes COTTON, except for the programme
EXTRA SHORT.
7 6 5 4 3 2 1
Function:
- Depending on the model, the user interface may include a buzzer.
- Switch off the appliance.
- Hold buttons 4 and 1 pressed simultaneously and turn the program selector one position to the
right. The buzzer is activated.
- You can deactivate the buzzer by repeatedly pressing the key combination.
Function:
- If no extra rinse key is available, you can select extra wash.
- This button is effective in the cycles cotton/coloured wash, synthetics and delicate fabrics.
- Two additional rinse cycles are added.
- No intermediate rinse, except after the last rinse cycle.
- Switch off the appliance.
- Hold buttons 5 and 1 pressed simultaneously and turn the program selector one position to the
right. The extra rinse is activated.
- You can deactivate extra wash by repeatedly pressing the key combination.
1 2 3 4
5 6 7 8
Function:
- Depending on the model, the user interface may include a buzzer.
- Switch off the appliance.
- Hold buttons 3 and 6 pressed simultaneously and turn the program selector one position to the
right. The buzzer is activated.
- You can deactivate the buzzer by repeatedly pressing the key combination.
Function:
- If no extra rinse key is available, you can select extra wash.
- This button is effective in the cycles cotton/coloured wash, synthetics and delicate fabrics.
- Two additional rinse cycles are added.
- No intermediate rinse, except after the last rinse cycle.
- Switch off the appliance.
- Hold buttons 2 and 5 pressed simultaneously and turn the program selector one position to the
right. The extra rinse is activated.
- You can deactivate extra wash by repeatedly pressing the key combination.
Function:
- The child safety function can be activated at the start of the program and also after the program
has started.
- Press keys 1 and 5 simultaneously and hold until a symbol appears on the LCD.
- The option is activated, the initiated wash program runs normally through and on
completion any further function of the appliance is disabled. The option remains saved when the
appliance is turned off.
- You can deactivate child safety by repeatedly pressing the key combination.
1. Electronic module
2. Program selector
3. User interface
4. Drum self position (DSP)
5. Pressure switch
6. NTC-sensor
7. Motor
8. Heating element
9. Inlet valve
10. Door lock
11. Drain pump
Functions:
- Taking data of the selected cycle programs through the module.
- Water level control in the tub; the level is recognized by the pressure switch.
- Cycle temperature control by a NTC sensor.
- Power supply of the heating element.
- Power supply of the drive motor and control of its speed by the tachymetric generator.
- Control of water inlet valves.
- Control of drain pump, door lock and DSP (drum self position).
In case of a power failure the module saves the just paused cycle.
- When the power supply to the appliance is restored again, the cycle starts where the program was
paused.
User Interface
The “User Interface” is placed inside the panel; it consists of the instruction and display module and the
program selector.
It consists of:
The program selector is connected to the instruction module by a flat line. And the instruction module is
connected to the main circuit board.
The program selector includes the “on/off” function and the wash programs. The “on/off” function is
controlled by the contacts P1/P2, P3 and P7/P5, P6.
The program selector has 12, 21 or 24 positions, depending on the appliance model. Every wash cycle
has an own binary code which is transmitted to the input/output electronic.
PTC resistor
lever
make-and-break
contact
locking part
When closing the lid the door lock gets an impulse from the electronic by contact 3. The impulse feeds
the magnetic coil over the PTC resistor. This moves the lever down and the tooth lock washer is
forwarded by another tooth. This can be heard by a click. The locking part is unlocked, the lid is closed.
When opening the lid, e.g. with the start/pause button or at the end of the cycle, the door lock gets two
impulses from the electronic. The tooth lock washer is moved twice. Only because of the second impulse
the lid can be opened immediately.
The second impulse unlocks the locking part mechanically through the tooth lock washer.
Why two impulses?
The door lock is controlled by a triac which is on the main circuit board. If there is a triac short circuit, the
electronic sends an impulse to the door lock. The customer could open the appliance, if the second
impulse was not required.
If there is a power failure during a wash cycle, the door lock requires approx. 2 min until the lid can be
opened. During this time the PTC bimetal cools down and the locking part opens.
Circuit Diagram
2
4
5
3
Security:
(see page Service - Program fault display E40)
Function:
The reed relay is closed if the metalic sheet, located on the pully, isn't between the magnet and the reed
relay. If the position of the metalic sheet is between those parts the contact of the reed relay is opened.
To mount the pulley in the correct way, you have to take care about following items:
The metal sheet located on the pulley should be in the drum self positioning device, if the door of the
drum is in the upper postion. The DSP is supplied with 5-6 V DC by the main board.
If the washing cycle is interrupted by the start pause button the drum has to be postioned within 10 sec.
During this time 2-3 attempts can be excecuted.If the drum isn't positioned during this time, the lid of the
appliance is released and can be opened. The LED drum positioned is not illuminated.
At the end of the cycle the positioning phase is 2 min until time out is reached.
*) Attention!
The flushing into the prewash chamber goes via hose 4.
The flushing into the main wash chamber goes via hose 2.
The simultaneous filling through hoses 2 and 4 provides the fill-in through the softener chamber.
*) Attention!
The flushing into the prewash resp. bleach chamber goes via hose 4.
This is possible due to a connecting channel in the flush-in chamber.
In doing so, approx. 75% water flows into the prewash chamber and aprox. 25% into the
bleach chamber.
It is not possible to select both options prewash and bleaching at the same time.
The flushing into the main wash chamber goes via hose 2.
The simultaneous filling through hoses 2 and 4 provides the fill-in through the softener chamber.
Pre wash
Main wash
Water inlet valve 1
Bleach
Softener
fN fTR fS
Level 1- sensing
AB-sensing
Supply valves are selected by 2 triacs, and the pressure switch switching levels are monitored by 2
control lines (sensing-wire).
Filling period is determined by control electronics.
Calculation of filling quantity is by measuring time interval between fTR contact closing and the closing of
pressure switch fN contact.
DGS-TDS-N 05.06 R.B. © Electrolux - 20 - 599 51 82 75 EN
Pressure switch
Anti-flooding-device
The third pressure switch level is used as an anti-flooding safety device: if the pressure switch
contact should close in the FULL position, the PCB actions the drain pump until the pressure switch
returns to the EMPTY position.
Heating element
The heating element is supplied with power directly from the control
electronics by means of a relay. For security reasons, 2 switching
contacts of the pressure switch are connected in series. The
switching positions are monitored by control electronics via 2 control
lines.
NTC-Sensor
1. NTC resistance
2. Metallic casing
3. Connections
4. Plastic casing
To check the NTC sensor function you can measure the ohmic resistance between the contacts
J5/1 and J5/2.
Security
- The pressure switch fN and fTR insures the power part security of the heater function.
- The µP will be break off if an anomaly on the termistance circuit is detected :
cut or short-circuit. (see Page Service-Program fault display E70)
- The heating phase is not executed.
Motor
The motor is directly phase-controlled via triac from the control electronics.
Relays K2, K3 are responsible for commuting the sense of rotation.
Field switching (if any) is controlled by relay K4.
Speed is monitored by tachometer generator g1 and controlled by control electronics.
Integral overheat protection disconnects the motor from power supply at 115°C.
Connection:
Safety
- If the triac for the motor is in short-circuit, or if the tachometer generator is interrupted, 4 trials are
executed in intervals of 1 minute each.
After a break of 20 minutes, the fifth and last trial is started. If the motor does not run this time, the
programme is aborted.
(see Page Service-Program fault display E60)
D55
Sek. 1/Min.
12 0
4 55
12 0
4 -55
N 55
Sek. 1/Min.
8 0
8 55
8 0
8 -55
E 55
Sek. 1/Min.
3 0
10 55
3 0
10 -55
E 55
Sek. 1/Min.
3 0
10 50
3 0
10 -50
PWL_1
Sek. 1/Min.
40 0
1 35
40 0
1 -35
PWL_4
Sek. 1/Min.
57 0
1 35
57 0
1 -35
C0
1/Min. Sek. AS
FUCS x nein
300 0 nein
FUCS x nein
450 0 nein
FUCS x nein
450 5 nein
650 0 nein
C1
1/Min. Sek. AS
FUCS x nein
FUCS imp x nein
FUCS x nein
450 30 AS
650 15 AS
850 10 AS
850 60 nein
C2
1/Min. Sek. AS
FUCS x nein
FUCS imp x nein
FUCS x nein
450 30 AS
650 20 AS
850 10 AS
1000 60 nein
COT_CF
1/Min. Sek. AS
FUCS x nein
FUCS imp x nein
FUCS x nein
450 30 AS
650 15 AS
850 5 AS
1000 95 nein
1150 75 nein
1400 110 nein
SYN_CF
1/Min. Sek. AS
FUCS x nein
FUCS imp x nein
FUCS x nein
450 5 nein
650 10 nein
900 55 nein
CF (Feinwäsche)
1/Min. Sek. AS
FUCS x nein
FUCS imp x nein
FUCS x nein
450 35 AS
700 5 AS
900 20 AS
CF (Wolle)
1/Min. Sek. AS
FUCS x nein
FUCS imp x nein
FUCS x nein
450 5 AS
650 1 AS
850 1 AS
1000 20 nein
Separater Schleudergang
1/Min. Sek. AS
FUCS x nein
FUCS imp x nein
FUCS x nein
450 10 AS
650 10 AS
850 10 AS
1000 10 nein
1150 10 nein
1400 20 nein
EASY_IRON_IMP
1/Min. Sek. AS
FUCS x nein
450 0 nein
FUCS x nein
650 0 AS
FUCS x nein
800 0 AS
FUCS x nein
900 0 AS
CSR
1/Min. Sek. AS
FUCS x nein
FUCS imp x nein
FUCS x nein
450 120 AS
Function:
The unbalance control includes 4 phases. These phases are of different duration and have different limits
of unbalance. The magnitude of the unbalance is calculated every 160 ms, hereby the magnitude is
compared to the fixed unbalance limits, and then it is decided whether the speed will be increased or
reduced by 2 1/min. FUCS starts at 55 1/min and ends ideally when reaching 115 1/min.
Phase 0: Phase 0 takes max.60sec. When the unbalance threshold of the first phase is reached, the
appliance performs a spin cycle with 100 1/min for 5 sec followed by a spin cycle pulse of
470 1/min.
Phase 1: The first phase takes max. 60 sec to obtain the required speed of 115 1/min. If the speed is
not reached after this 60 sec, the spinning cycle will be stopped. The laundry is dispersed and
it is changed to phase 2.
Phase 2: Phase 2 takes max. 180 sec. Here it is tried to obtain the speed of 115 1/min with various
unbalance limits. If the speed is not reached after 180 sec, the spinning cycle will be stopped
again. The laundry is dispersed and it is changed to phase 3.
Phase 3: In phase 3, the required speed is reduced to 85 1/min. Within 90 secs, speed should be
reached, the machine then runs a spin-dry cycle at 100 1/min and a subsequent spin-dry
pulse at 470 1/min, then again starting by phase 1. If the speed is reached, a reduced spin-
dry cycle at 650 1/min is carried out.
If the speed is not reached, spin-dry is skipped.
1/min
Perfect balance
- Reversing
- FUCS phase 0
with spin-dry pulse
- Reversing
- FUCS phase 1
- regular spin-dry
- Low speed
- FUCS phase 0
- FUCS phase 1
- FUCS phase 2
- FUCS phase 0
with spin pulse
- FUCS phase 1
- FUCS phase 2
- FUCS phase 3
with spin pulse
- FUCS phase 1
- FUCS phase 2
- FUCS phase 3
- Normal spin
- FUCS phase 0
- FUCS phase 1
- FUCS phase 2
- FUCS phase 3
with spin pulse
- FUCS phase 1
- FUCS phase 2
- FUCS phase 3
- reduced-speed spin
- FUCS phase 0
- FUCS phase 1
- FUCS phase 2
- FUCS phase 3
- FUCS phase 1
- FUCS phase 2
- FUCS phase 3
- no spin
Spin-dry Anti-Foam
(at level fTR) Spin-dry
FUCS FUCS
If pressure switch contact fTR closes (“full” position), the spin-dry cycle is interrupted and the drain
pump will run until the contact is reopening (“empty” position), and the spin-dry cycle will be
continued.
7 6 5 4 3 2 1
Position of the
rotary switch Button Test function
Off Off
24 - 21 - 12
Positions
01 Button 1 1) Start of the customer service testprogram
and 2) LED - Test
Button 2 LEDs are step by step illuminated.
If you press a button the according LED is on.
09 DSP
The drum is positioned if level < fSch
1 2 3 4
5 6 7 8
Position of the
rotary switch Button Test function
Off Off
24 - 21 - 12
Positions
01 Button 1 1) Start of the customer service testprogram
and 2) LCD - Test
Button 2
02 Water channel mainwash
Water intake up to savety level fS
Time max. 5 min
Valve mainwash
09 DSP
The drum is positioned if level < fSch
Service Program
W W 1 W 1 W W W W
M M D M D M M M M
2 1 0 1 0 1 2 2 3
0 0 0 0 0 0 0 0 0
Fault Alarm
0 0 1 0 2 0 0 0 0
Type of fault Remedy Code
code 0 0 0 0 0 0 0 0 0
9 0 p E N N
l V E E
u O W W
s
© Electrolux
Service Program
W W 1 W 1 W W W W
M M D M D M M M M
2 1 0 1 0 1 2 2 3
0 0 0 0 0 0 0 0 0
Fault Alarm 0 0 1 0 2 0 0 0 0
Type of fault Remedy Code
code 0 0 0 0 0 0 0 0 0
9 0 p E N N
l V E E
u O W W
s
© Electrolux
Door is not unlocking at the end of cycle Tout 4 min Replace electronic
DGS-TDS-N 05.06 R.B.
Service Program
E E W E W E E E E
W W 1 W 1 W W W W
M M D M D M M M M
2 1 0 1 0 1 2 2 3
0 0 0 0 0 0 0 0 0
Fault Alarm 0 0 1 0 2 0 0 0 0
Type of fault Remedy Code
code 0 0 0 0 0 0 0 0 0
9 0 p E N N
l V E E
u O W W
© Electrolux
E5D FCV cannot receive and/or transmit a message for more Replace cable 1,6 A X
than 2 seconds
E5E There are communication problems in betw een FCV Replace electronic 1 A X
control board and mainboard
E5F FCV control board is continuously asking for configuration Replace motor control board, replace cable 1 A X
parameters due to repetitive reset Replace electronic
EN
E E W E W E E E E
W W 1 W 1 W W W W
DGS-TDS-N 05.06 R.B.
Service Program
M M D M D M M M M
2 1 0 1 0 1 2 2 3
0 0 0 0 0 0 0 0 0
Fault Alarm 0 0 1 0 2 0 0 0 0
Type of fault Remedy Code
code 0 0 0 0 0 0 0 0 0
9 0 p E N N
l V E E
u O W W
s
© Electrolux
E92 Incongruence betw een In/Output electronic and electronic In/Output electronic is incompatible 1 A X X X X X
w ith electronic
E93 Configuration error Wrong configuration of the machine 1 A X X X X X X X
E94 Lost of cycle datas Wrong configuration of the machine 1 A X X X X X X X
Replace electronic
EN
E95 Communication error betw een microprocessor and EEPROM Replace electronic 0 A X X X X X X
E E W E W E E E E
DGS-TDS-N 05.06 R.B.
Service Program
W W 1 W 1 W W W W
M M D M D M M M M
2 1 0 1 0 1 2 2 3
0 0 0 0 0 0 0 0 0
Fault Alarm
0 0 1 0 2 0 0 0 0
Type of fault Remedy Code
code 0 0 0 0 0 0 0 0 0
9 0 p E N N
l V E E
u O W W
s
© Electrolux
E96 Incongruence betw een Hardw are-version and Wrong configuration of the machine 0 A X X
cycles configuration Replace electronic
E97 Incongruence betw een selector and cycles configuration Wrong configuration of the machine 0 A X X X X X X
Replace electronic
E99 Connection betw een loudspeaker and In/Output electronic Replace loudspeaker 0 A X X
Replace w iring
E9A Firmw are betw een loudspeaker and In/Output electronic not ok Replace In/Output electronic 0 A X X
EA0 EA1 DSP defect Replace DSP, Replace electronic 5 S X X X X X X X
Replace w iring, Cut drive belt
- 37 -
Service Program
W W 1 W 1 W W W W
M M D M D M M M M
2 1 0 1 0 1 2 2 3
0 0 0 0 0 0 0 0 0
Fault Alarm
0 0 1 0 2 0 0 0 0
Type of fault Remedy Code
code 0 0 0 0 0 0 0 0 0
9 0 p E N N
l V E E
u O W W
s
© Electrolux
6 after 5 attempt
Service Program
In order to read the last alarm code memorized in the EEPROM on the PCB:
- Irrespective of the type of PCB and configuration, turn the programme selector clockwise to the
tenth position.
The alarm is displayed by a repeated flashing sequence of the two LEDs (0.4 seconds lit, 0.4 seconds
off, with an interval of 2.5 seconds between sequences). The buzzer (if featured) will sound ”bips” in
synchronization with the flashing of the LED 22:
L6 L16
L7 L17
L8 L18
L9 L19
L10 L11 L12 L13 L14 L28 L15 L20
L21
L22
7 6 5 4 3 2 1 L23
- The program-end LED (LED 22) shows the first figure of the number “5” of the error code
(Error group )
- The Start/Pause-LED (LED 15) shows the second digit of the number “3” of the error code
(number within the group)
These two LEDs are featured on all models (though they are configured differently), and flash
simultaneously.
7 6 5 4 3 2 1
The last alarm code can be displayed even if the programme selector is not in the 10th position
(service test mode) or if the appliance is in normal operating mode (e.g. during the execution of an
washing programme):
- The alarm sequence continues as long as the two buttons are held down
- While the alarms are displayed, the appliance continues to perform the cycle or, if in the
programme selection phase, maintains the previously-selected options in memory.
- Hold one of the buttons 2 - 7 together with button 1 pressed in until the signal buzzer is heard
once (all LEDs off).
- after reading the alarm code, to check whether the alarm re-occurs during diagnostics
7 6 5 4 3 2 1
1 2 3 4
5 6 7 8
7 6 5 4 3 2 1
1 2 3 4
5 6 8 7
1 2 3 4
5 6 7 8
operating time
20
30
40
50
60
1000
1200
1400
0
200
400
600
800
0:00:01
0
DGS-TDS-N 05.06 R.B.
Program cycles
0:00:01
0:03:24
0:03:27
0:06:47
0:06:53
0:10:10
0:10:19
0:13:33
0:13:45
0:16:56
0:17:11
0:20:19
0:20:37
0:23:42
0:24:03
0:27:05
0:27:29
0:30:28
© Electrolux
0:30:55
0:33:51
0:34:21
0:37:14
0:37:47
0:40:37
0:41:13
0:44:00
0:44:39
0:47:23
0:48:05
0:50:46
0:51:31
0:54:09
0:54:57
0:57:32
0:58:23
1:00:55
1:01:49
- 49 -
1:04:18
wash_temp
drum_speed
1:05:15
1:07:41
1:08:41
1:11:04
1:12:07
1:14:27
Software W1A30105
1:15:33
1:17:50
1:18:59
1:21:13
1:22:25
1:24:36
1:25:51
1:27:59
1:29:17
1:31:22
1:32:43
1:34:45
1:36:09
1:38:08
1:39:35
1:41:31
1:43:01
1:44:54
1:46:27
1:48:17
1:49:53
1:51:40
599 51 82 75
1:53:19
1:55:03
1:56:45
1:58:26
2:00:11
2:01:49
2:03:37
2:05:12
2:07:03
2:08:35
2:10:29
EN
2:11:58
2:13:55
1000
1200
1400
10
20
30
40
50
60
70
200
400
600
800
0
0:00:01
0
DGS-TDS-N 05.06 R.B.
Program cycles
0:00:01
0:03:24
0:03:27
0:06:47
0:06:53
0:10:10
0:10:19
0:13:33
0:13:45
0:16:56
0:17:11
0:20:19
0:20:37
0:23:42
0:24:03
0:27:05
0:27:29
0:30:28
© Electrolux
0:30:55
0:33:51
0:34:21
0:37:14
0:37:47
0:40:37
0:41:13
0:44:00
0:44:39
0:47:23
0:48:05
0:50:46
0:51:31
0:54:09
0:54:57
0:57:32
0:58:23
1:00:55
1:01:49
- 50 -
1:04:18
wash_temp
drum_speed
1:05:15
Software W1A30105
1:07:41
1:08:41
1:11:04
1:12:07
1:14:27
1:15:33
1:17:50
1:18:59
1:21:13
1:22:25
1:24:36
1:25:51
1:27:59
1:29:17
1:31:22
1:32:43
1:34:45
1:36:09
1:38:08
1:39:35
1:41:31
1:43:01
1:44:54
1:46:27
1:48:17
1:49:53
1:51:40
599 51 82 75
1:53:19
1:55:03
1:56:45
1:58:26
2:00:11
2:01:49
2:03:37
2:05:12
2:07:03
2:08:35
2:10:29
EN
2:11:58
2:13:55
1000
1200
1400
10
20
30
40
50
60
70
200
400
600
800
0
0:00:01
0
DGS-TDS-N 05.06 R.B.
Program cycles
0:00:01
0:03:24
0:03:27
0:06:47
0:06:53
0:10:10
0:10:19
0:13:33
0:13:45
0:16:56
0:17:11
0:20:19
0:20:37
0:23:42
0:24:03
0:27:05
0:27:29
0:30:28
© Electrolux
0:30:55
0:33:51
0:34:21
0:37:14
0:37:47
0:40:37
0:41:13
0:44:00
0:44:39
0:47:23
0:48:05
0:50:46
0:51:31
0:54:09
0:54:57
0:57:32
0:58:23
1:00:55
1:01:49
- 51 -
1:04:18
wash_temp
drum_speed
1:05:15
1:07:41
Software W1A30105
1:08:41
1:11:04
1:12:07
1:14:27
1:15:33
1:17:50
1:18:59
1:21:13
1:22:25
1:24:36
1:25:51
1:27:59
1:29:17
1:31:22
1:32:43
1:34:45
1:36:09
1:38:08
1:39:35
1:41:31
1:43:01
1:44:54
1:46:27
1:48:17
1:49:53
1:51:40
599 51 82 75
1:53:19
1:55:03
1:56:45
1:58:26
2:00:11
2:01:49
2:03:37
2:05:12
2:07:03
2:08:35
2:10:29
EN
2:11:58
2:13:55
10
20
30
40
50
60
10
20
30
40
50
60
70
0
0
0:00:01 0:00:01
DGS-TDS-N 05.06 R.B.
Program cycles
0:04:02 0:04:02
0:08:03 0:08:03
0:12:04 0:12:04
0:16:05 0:16:05
0:20:06 0:20:06
0:24:07 0:24:07
0:28:08 0:28:08
0:32:09 0:32:09
0:36:10 0:36:10
© Electrolux
0:40:11 0:40:11
0:44:12 0:44:12
0:48:13 0:48:13
0:52:14 0:52:14
0:56:15 0:56:15
1:00:16 1:00:16
1:04:17 1:04:17
1:08:18 1:08:18
1:12:19 1:12:19
- 52 -
1:16:20 1:16:20
drum_speed
wash_temp
Software W1A30105
1:20:21 1:20:21
1:24:22 1:24:22
1:28:23 1:28:23
1:32:24 1:32:24
1:36:25 1:36:25
1:40:26 1:40:26
1:44:27 1:44:27
1:48:28 1:48:28
1:52:29 1:52:29
1:56:30 1:56:30
2:00:31 2:00:31
2:04:32 2:04:32
2:08:33 2:08:33
2:12:34 2:12:34
599 51 82 75
2:16:35 2:16:35
2:20:36 2:20:36
2:24:37 2:24:37
2:28:38 2:28:38
2:32:39 2:32:39
EN
2:36:40 2:36:40
1000
1200
10
20
30
40
50
60
70
200
400
600
800
0
0:00:01
0
DGS-TDS-N 05.06 R.B.
Program cycles
0:00:01
0:02:35
0:02:37
0:05:09
0:05:13
0:07:43
0:07:49
0:10:17
0:10:25
0:12:51
0:13:01
0:15:25
0:15:37
0:17:59
0:18:13
0:20:33
0:20:49
0:23:07
© Electrolux
0:23:25
0:25:41
0:26:01
0:28:15
0:28:37
0:30:49
0:31:13
0:33:23
0:33:49
0:35:57
0:36:25
0:38:31
0:39:01
0:41:05
0:41:37
0:43:39
0:44:13
0:46:13
0:46:49
- 53 -
0:48:47
wash_temp
drum_speed
0:49:25
0:51:21
0:52:01
0:53:55
0:54:37
0:56:29
0:57:13
0:59:03
0:59:49
1:01:37
1:02:25
1:04:11
1:05:01
1:06:45
1:07:37
1:09:19
1:10:13
1:11:53
1:12:49
1:14:27
1:15:25
1:17:01
1:18:01
1:19:35
1:20:37
1:22:09
1:23:13
1:24:43
599 51 82 75
1:25:49
1:27:17
1:28:25
1:29:51
1:31:01
1:32:25
1:33:37
1:34:59
1:36:13
1:37:33
1:38:49
EN
1:40:07
1:41:25
10
15
20
25
30
35
40
45
1000
1200
0
200
400
600
800
0:00:01
0
DGS-TDS-N 05.06 R.B.
Program cycles
0:00:01
0:01:44
0:01:45
0:03:27
0:03:29
0:05:10
0:05:13
0:06:53
0:06:57
0:08:36
0:08:41
0:10:19
0:10:25
0:12:02
0:12:09
0:13:45
0:13:53
0:15:28
© Electrolux
0:15:37
0:17:11
0:17:21
0:18:54
0:19:05
0:20:37
0:20:49
0:22:20
0:22:33
0:24:03
0:24:17
0:25:46
0:26:01
0:27:29
0:27:45
0:29:12
0:29:29
0:30:55
0:31:13
- 54 -
0:32:38
wash_temp
drum_speed
0:32:57
0:34:21
0:34:41
0:36:04
0:36:25
0:37:47
0:38:09
0:39:30
0:39:53
0:41:13
0:41:37
0:42:56
0:43:21
0:44:39
0:45:05
0:46:22
0:46:49
0:48:05
0:48:33
0:49:48
0:50:17
0:51:31
0:52:01
0:53:14
0:53:45
0:54:57
0:55:29
0:56:40
599 51 82 75
0:57:13
0:58:23
0:58:57
1:00:06
1:00:41
1:01:49
1:02:25
1:03:32
1:04:09
1:05:15
1:05:53
EN
1:06:58
10
15
20
25
30
35
40
1000
1200
0
200
400
600
800
0:00:01
0
DGS-TDS-N 05.06 R.B.
Program cycles
0:00:01
0:01:21
0:01:22
0:02:41
0:02:43
0:04:01
0:04:04
0:05:21
0:05:25
0:06:41
0:06:46
0:08:01
0:08:07
0:09:21
0:09:28
0:10:41
0:10:49
0:12:01
© Electrolux
0:12:10
0:13:21
0:13:31
0:14:41
0:14:52
0:16:01
0:16:13
0:17:21
0:17:34
0:18:41
0:18:55
0:20:01
0:20:16
0:21:21
0:21:37
0:22:41
0:22:58
0:24:01
0:24:19
- 55 -
0:25:21
wash_temp
drum_speed
0:25:40
0:26:41
0:27:01
0:28:01
0:28:22
0:29:21
0:29:43
0:30:41
0:31:04
0:32:01
0:32:25
0:33:21
0:33:46
0:34:41
0:35:07
0:36:01
0:36:28
0:37:21
0:37:49
0:38:41
0:39:10
0:40:01
0:40:31
0:41:21
0:41:52
0:42:41
0:43:13
0:44:01
599 51 82 75
0:44:34
0:45:21
0:45:55
0:46:41
0:47:16
0:48:01
0:48:37
0:49:21
0:49:58
0:50:41
0:51:19
EN
0:52:01
0:52:40
1000
1200
1400
200
400
600
800
10
15
20
25
30
35
40
45
0
0
5
00:00:01 00:00:01
DGS-TDS-N 05.06 R.B.
Program cycles
00:03:23 00:03:26
00:06:45 00:06:51
00:10:07 00:10:16
00:13:29 00:13:41
00:16:51 00:17:06
00:20:13 00:20:31
00:23:35 00:23:56
00:26:57 00:27:21
© Electrolux
00:30:19 00:30:46
00:33:41 00:34:11
00:37:03 00:37:36
00:40:25 00:41:01
00:43:47 00:44:26
Software W1A30106
00:47:09 00:47:51
00:50:31 00:51:16
00:53:53 00:54:41
00:57:15 00:58:06
01:00:37 01:01:31
- 56 -
01:03:59 01:04:56
wash_temp
drum_speed
01:07:21 01:08:21
01:10:43 01:11:46
01:14:05 01:15:11
01:17:27 01:18:36
01:20:49 01:22:01
01:24:11 01:25:26
01:27:33 01:28:51
01:30:55
01:32:16
01:34:17
01:35:41
01:37:39
01:39:06
01:41:01
01:42:31
01:44:23
01:45:56
01:47:45
01:49:21
01:51:07
01:52:46
599 51 82 75
01:54:29
01:56:11
01:57:51
01:59:36
02:01:13
02:03:01
02:04:35
02:06:26
02:07:57
02:09:51
EN
02:11:19
02:13:16
1000
1200
200
400
600
800
10
15
20
25
30
35
40
45
0
0
5
00:00:01 00:00:01
DGS-TDS-N 05.06 R.B.
Program cycles
00:02:00 00:02:02
00:03:59 00:04:03
00:05:58 00:06:04
00:07:57 00:08:05
00:09:56 00:10:06
00:11:55 00:12:07
00:13:54 00:14:08
00:15:53 00:16:09
00:17:52 00:18:10
© Electrolux
00:19:51 00:20:11
00:21:50 00:22:12
00:23:49 00:24:13
00:25:48 00:26:14
Software W1A30106
00:27:47 00:28:15
00:29:46 00:30:16
00:31:45 00:32:17
00:33:44 00:34:18
00:35:43 00:36:19
- 57 -
drum_speed
00:37:42
wash_temp
00:38:20
00:39:41 00:40:21
00:41:40 00:42:22
00:43:39 00:44:23
00:45:38
00:46:24
00:47:37 00:48:25
00:49:36 00:50:26
00:51:35
00:52:27
00:53:34
00:54:28
00:55:33
00:56:29
00:57:32
00:58:30
00:59:31
01:00:31
01:01:30
01:02:32
01:03:29
01:04:33
01:05:28
599 51 82 75
01:06:34
01:07:27
01:08:35
01:09:26
01:10:36
01:11:25
01:12:37
01:13:24
01:14:38
01:15:23
01:16:39
EN
01:17:22
1000
1200
200
400
600
800
10
15
20
25
30
35
40
45
50
0
0
00:00:01 00:00:01
DGS-TDS-N 05.06 R.B.
Program cycles
00:01:10 00:01:11
00:02:19 00:02:21
00:03:28 00:03:31
00:04:37 00:04:41
00:05:46 00:05:51
00:06:55 00:07:01
00:08:04 00:08:11
00:09:13 00:09:21
© Electrolux
00:10:22 00:10:31
00:11:31 00:11:41
00:12:40 00:12:51
00:13:49
Software W1A30106
00:14:01
00:14:58 00:15:11
00:16:07 00:16:21
00:17:16
00:17:31
00:18:25
00:18:41
00:19:34
- 58 -
00:19:51
00:20:43
00:21:01
drum_speed
wash_temp
00:21:52
00:22:11
00:23:01
00:23:21
00:24:10
00:24:31
00:25:19
00:25:41
00:26:28
00:26:51
00:27:37
00:28:01
00:28:46
00:29:11
00:29:55
00:30:21
00:31:04
00:31:31
00:32:13
00:32:41
00:33:22
00:33:51
00:34:31
599 51 82 75
00:35:01
00:35:40
00:36:11
00:36:49
00:37:21
00:37:58
00:38:31
00:39:07
00:39:41
00:40:16
EN
00:40:51
Changes
Date Page changed
07.05 2, 4, 5, 6, 7, 8, 9, 10, 12, 29, 30, 33, 37, 38, 39, 40, 41, 52, 53, 54
05.06 2, 4, 5, 6, 8, 9, 10 , 12, 32, 33, 34, 35, 36, 37, 38, 42, 44, 45, 58