Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
4 1 Valet Switch
5 2 24” Cable Ties
6 2 3-Button Transmitter
General Applicability
7 1 Owner’s Card
Vehicles with power door locks.
Recommended Tools
Safety Tools
Special Tools
Special Chemicals
PREPARATION
INSTALLATION PREPARATION
VEHICLE PREPARATION
PREPARATION
5. Remove the plastic storage compartment at left
the end of dash to gain access to the driver’s
side J/B.
PREPARATION
MODULE PREPARATION
1. Secure the antenna to the back side of the module using the supplied foam pad.
2. Route the antenna and secure it to the main harness with tape or cable ties.
IMPORTANT: Failure to route the antenna cable as described will result in reduced range of the system.
INSTALLATION PROCEDURES
INSTALLATION PROCEDURES
MOUNTING THE MAIN CONTROL
MODULE KEYLESS MODULE
Secure the main module to the vehicle harness
connected to the JB in the driver’s side kick panel
area. Secure in place with the long cable ties
provided.
T-TAP INSTALLATION
When installing female T-Tap connectors, be sure the wire is located inside the wire channel of the female
T-Tap connector before closing the connector over the wire with pliers.
Step A Step B Step C
STOP
IMPORTANT! After installation, inspect and ensure that Keyless System Harnesses are clear of
all HOT, SHARP or MOVING objects.
Southeast Toyota Distributors, LLC
Page 5 of 12
CHASSIS GROUND - Connect the ring terminal to the
10mm bolt under the steering column (factory ground).
Page 6 of 12
2 Pin Molex Connector -
Plug into Toggle Control.
WIRING DIAGRAM
BLUE/WHITE [Driver
Door Unlock Motor -
Towards Body ECU]
DETAIL “A”
(See Detail A)
DRIVER’S DOOR UNLOCK CIRCUIT Harness
Cut the PINK wire in connector GD1, location 20. Wires
Strip the insulation from both sides of the cut wire, BLUE w/
and crimp the PINK/WHITE wire from the keyless WHITE Cut & Strip
harness to the HARNESS side of the cut wire. Crimp Existing Wire
the BLUE/WHITE WIRE from the keyless harness
to the CONNECTOR side of the cut wire. WHITE
KEYLESS ENTRY SYSTEM
TOYOTA YARIS KEYLESS ENTRY SYSTEM
CONNECTOR DETAILS
CONNECTOR D8: IGNITION SWITCH CONNECTOR GD1: DOOR LOCKS
Location: Steering Column Location: Driver’s Side Kick Panel Area
White Connector Blue Connector
Pin 5 Pin 6
Brown Wire Tan or Orange Wire
Pin 1 1 2 3 4 Pin 4 Door Lock Switch Door Unlock Switch
Green Wire 5 6 7 8 Yellow Wire
+12V Accessory +12V Battery
1 10
10 1
11 2 3 4 5 6 7 8 9 20
12 13 14 15 16 17 18 19 20 9 8 7 6 5 4 3 2 11
19 18 17 16 15 14 13 12
KEYLESS CAR
Red Yellow
Pin 20
Yellow Green Pink Wire (Download)
Driver’s Door Lock Motor - Unlock
Pin 9
Blue Wire
CONNECTOR D3: HORN Door Unlock Detect Switch
Location: Lower Steering Column Cover Area
Black Connector KEYLESS CAR
Pink Brown
Pink/White Tan or Orange
Pink/White Blue
1 2 3 4 5 6
Pin 8 7 8 9 10 11 12
Black
Horn
Blue/White Pink (ECU Side) *
White Pink (Lock Side)
KEYLESS CAR
* This vehicle wire must be cut in half.
Green/Red Black Refer to page 6 for instructions.
1 2 3 4
5 6 7 8 9 10 11 12 13
Pin 13
White Wire
Headlights** (SEE PAGE 8) Taillights
KEYLESS CAR
White White
HEADLIGHT RELAY
Location: Lower Steering Column Cover Area Location: Lower Steering Column Cover Area
D4 D4
White White
Connector Connector
1 2 3 4 1 2 3 4
5 6 7 8 9 10 11 12 13 5 6 7 8 9 10 11 12 13
!
Failure to use the headlight relay as D8
instructed will cause damage to the keyless White
entry module. Connector
Pin 4
HEADLIGHT RELAY
1 2 3 4
5 6 7 8 Yellow Wire
+12V Battery
KEYLESS CAR
Red Yellow
PINK [Headlight Output]: Use blue T-Tap and connect to the PINK wire in connector
D4, location 9.
WHITE [Headlight Ground]: Use yellow T-Tap and connect to the WHITE/BLACK
wire in connector D4, location 11.
RED [+12VDC Battery]: Use blue T-Tap and connect to the YELLOW wire in
connector D8 (ignition switch), location 4.
4 AMP