Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Data Sheet
2024
29304F
HIGH-VOLTAGE, HIGH-CURRENT
DARLINGTON ARRAYS
Ideally suited for interfacing between low-level logic circuitry and
multiple peripheral power loads, the Series ULN20xxA/L high-voltage,
1 16 high-current Darlington arrays feature continuous load current ratings
to 500 mA for each of the seven drivers. At an appropriate duty cycle
2 15 depending on ambient temperature and number of drivers turned ON
3 14
simultaneously, typical power loads totaling over 230 W (350 mA x 7,
95 V) can be controlled. Typical loads include relays, solenoids,
4 13 stepping motors, magnetic print hammers, multiplexed LED and
incandescent displays, and heaters. All devices feature open-collector
5 12 outputs with integral clamp diodes.
6 11 The ULN2003A/L and ULN2023A/L have series input resistors
selected for operation directly with 5 V TTL or CMOS. These devices
7 10 will handle numerous interface needs — particularly those beyond the
capabilities of standard logic buffers.
8 9
The ULN2004A/L and ULN2024A/L have series input resistors for
operation directly from 6 to 15 V CMOS or PMOS logic outputs.
Dwg. No. A-9594
The ULN2003A/L and ULN2004A/L are the standard Darlington
Note that the ULN20xxA series (dual in-line arrays. The outputs are capable of sinking 500 mA and will withstand
package) and ULN20xxL series (small-outline at least 50 V in the OFF state. Outputs may be paralleled for higher
IC package) are electrically identical and share load current capability. The ULN2023A/L and ULN2024A/L will
a common terminal number assignment. withstand 95 V in the OFF state.
These Darlington arrays are furnished in 16-pin dual in-line plastic
packages (suffix “A”) and 16-lead surface-mountable SOICs (suffix
“L”). All devices are pinned with outputs opposite inputs to facilitate
ease of circuit board layout. All devices are rated for operation over the
temperature range of -20°C to +85°C. Most (see matrix, next page) are
also available for operation to -40°C; to order, change the prefix from
ABSOLUTE MAXIMUM RATINGS “ULN” to “ULQ”.
Output Voltage, VCE
(ULN200xA and ULN200xL) ........ 50 V
(ULN202xA and ULN202xL) ........ 95 V FEATURES
Input Voltage, VIN ................................ 30 V
■ TTL, DTL, PMOS, or CMOS-Compatible Inputs
Continuous Output Current,
■ Output Current to 500 mA
IC ................................................. 500 mA
■ Output Voltage to 95 V
Continuous Input Current, IIN ........... 25 mA
■ Transient-Protected Outputs
Power Dissipation, PD
■ Dual In-Line Plastic Package or Small-Outline IC Package
(one Darlington pair) ..................... 1.0 W
(total package) ....................... See Graph
Operating Temperature Range,
TA .................................. -20°C to +85°C
Storage Temperature Range,
TS ................................. -55°C to +150°C
x = digit to identify specific device. Characteristic shown applies to family of
devices with remaining digits as shown. See matrix on next page.
2003 THRU 2024
HIGH-VOLTAGE,
HIGH-CURRENT
DARLINGTON ARRAYS
VCE(MAX) 50 V 95 V
5V ULN2003A* ULN2023A*
TTL, CMOS ULN2003L* ULN2023L
*Also available for operation between -40°C and +85°C. To order, change
PARTIAL SCHEMATICS prefix from “ULN” to “ULQ”.
ULN20x3A/L (Each Driver)
COM
2.7K 2.5
ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS
7.2K 3K
2.0
1.5
Dwg. No. A-9651
0.5
COM SUFFIX 'L', R θJA = 90°C/W
10.5K
0
7.2K 3K 25 50 75 100 125 150
AMBIENT TEMPERATURE IN °C
Dwg. GP-006A
Dwg. No. A-9898A X = Digit to identify specific device. Specification shown applies to family of
devices with remaining digits as shown. See matrix above.
Complete part number includes suffix to identify package style: A = DIP, L = SOIC.
www.allegromicro.com
2003 THRU 2024
HIGH-VOLTAGE,
HIGH-CURRENT
DARLINGTON ARRAYS
Complete part number includes suffix to identify package style: A = DIP, L = SOIC.
I
hFE = C
µA µA IB
ICEX ICEX
OPEN VIN
V
IB VCE IC
µA
IIN IIN IC
mA OPEN µA
VIN VIN
V V
VCE IC
VR VIN
50% 50%
INPUT
µA IF
IR V
OUTPUT t pHL t pHL
VF
OPEN 50% 50%
OPEN
+50 V
Vin
INPUT
Dwg. No. A-9735A Dwg. No. A-9736A ULN20X3* 3.5 V PULSE
93 Ω 100 Ω
GENERATOR
ULN20X4* 12 V PRR = 10KHz OUT
DC = 50%
30 Ω 50 pF
X = Digit to identify specific device. Specification shown applies to family of devices with remaining digits as shown.
www.allegromicro.com
2003 THRU 2024
HIGH-VOLTAGE,
HIGH-CURRENT
DARLINGTON ARRAYS
ALLOWABLE COLLECTOR CURRENT TYPICAL APPLICATIONS
AS A FUNCTION OF DUTY CYCLE
(Dual In-line-Packaged Devices, Suffix ‘A’) +VSS +V
600 1 16
2 15
1
OUTPUT CURRENT IN mA/CHANNEL
3 14
2
400 4 13
3
4 5 12
5
6
7 6 11
200 7 10
NUMBER OF OUTPUTS
CONDUCTING PMOS
SIMULTANEOUSLY OUTPUT 8 9
TA = +70°C
RθJA = 60°C/W
Dwg. No. A-9652
0
0 20 40 60 80 100 +VDD +V
DUTY CYCLE IN PER CENT
Dwg. GP-070 1 16
600 3 14
TA = +70°C 4 13
RθJA = 90°C/W
OUTPUT CURRENT IN mA/CHANNEL
5 12
400 6 11
200 Ω
2 7 10 2N4901
200 Ω
3 8 9
4
200 5
6
7
CMOS
OUTPUT
NUMBER OF OUTPUTS
CONDUCTING Dwg. No. A-9654A
SIMULTANEOUSLY
0
0 20 40 60 80 100
DUTY CYCLE IN PER CENT
Dwg. GP-044A
COLLECTOR CURRENT IN mA
400 400
E
AG
L
L
LT
CA
CA
VO
T
PI
EN
PI
TY
TY
RR
IO
U
AT
C
T
UR
PU
IN
AT
EQ
AX
.R
AX
M
0 0
0 0.5 1.0 1.5 2.0 0 200 400 600
COLLECTOR-EMITTER SATURATION VOLTAGE INPUT CURRENT IN µA
Dwg. GP-067 Dwg. GP-068
2 15
3 14
2.0
IN
4 13 M
MU
INPUT CURRENT IN mA — I
XI
MA
5 12
1.5
6 11 AL
P IC
TY
7 10
1.0
8 9
TTL 0.5
OUTPUT AREA OF NORMAL OPERATION
WITH STANDARD OR SCHOTTKY TTL
3 14
4 13
1.5
INPUT CURRENT IN mA — IIN
RP 5 12
6 11
UM
XIM
7 10 MA
1.0
8 9
AL
TTL TYPIC
OUTPUT 0.5
0
5 6 7 8 9 10 11 12
INPUT VOLTAGE
Dwg. GP-069-1
www.allegromicro.com
2003 THRU 2024
HIGH-VOLTAGE,
HIGH-CURRENT
DARLINGTON ARRAYS
0.430
MAX
0.280
0.300
0.240 BSC
1 8
0.070 0.100 0.005
0.045 0.775 BSC MIN
0.735
0.210
MAX
0.015 0.150
MIN 0.115
0.022
Dwg. MA-001-16A in
0.014
Dimension in Millimeters
(for reference only)
0.355
0.204
16 9
10.92
MAX
7.11
7.62
6.10 BSC
1 8
1.77 2.54 0.13
1.15 19.68 BSC MIN
18.67
5.33
MAX
0.39 3.81
MIN 2.93
0.558
Dwg. MA-001-16A mm
0.356
0.1574 0.2440
0.1497 0.2284 0.050
0.016
0.020 1 2 3 0.050
0.013 0.3937 BSC 0° TO 8°
0.3859
0.0688
0.0532
Dwg. MA-007-16 in
0.0040 MIN.
Dimension in Millimeters
(controlling dimensions)
16 9
0.25
0.19
4.00 6.20
3.80 5.80 1.27
0.40
0.51 1 2 3 1.27
0.33 10.0 BSC 0° TO 8°
9.80
1.75
1.35
Dwg. MA-007-16A mm
0.10 MIN.
www.allegromicro.com
2003 THRU 2024
HIGH-VOLTAGE,
HIGH-CURRENT
DARLINGTON ARRAYS
www.datasheetcatalog.com
.. (600mA PEAK)
OUTPUT VOLTAGE 50V
INTEGRATED SUPPRESSION DIODES FOR
. INDUCTIVE LOADS
OUTPUTS CAN BE PARALLELED FOR
.. HIGHER CURRENT
TTL/CMOS/PMOS/DTL COMPATIBLE INPUTS
INPUTS PINNED OPPOSITE OUTPUTS TO
DIP16
SO16
SCHEMATIC DIAGRAM
THERMAL DATA
Symbol Parameter DIP16 SO16 Unit
Rth j-amb Thermal Resistance Junction-ambient Max. 70 120 °C/W
2/8
ULN2001A - ULN2002A - ULN2003A - ULN2004A
3/8
ULN2001A - ULN2002A - ULN2003A - ULN2004A
TEST CIRCUITS
Figure 1a. Figure 1b.
Figure 2. Figure 3.
Figure 4. Figure 5.
Figure 6. Figure 7.
4/8
ULN2001A - ULN2002A - ULN2003A - ULN2004A
Figure 8: Collector Current versus Input Current Figure 9: Collector Current versus Saturation
Voltage
Ic D96IN454
Ic D96IN453
(mA) (mA)
Tj=25˚C
500 500
Tj=25˚C
400 400
Max Max
300 300
200 200
TYPICAL TYPICAL
100 100
0 0
0 100 200 300 400 500 Ib(µA) 0.0 0.5 1.0 1.5 Vce(sat)
Figure 10: Peak Collector Current versus Duty Figure 11: Peak Collector Current versus Duty
Cycle Cycle
400 400
2
300 300
Tamb=70˚C 3
(DIP16) 5
200 200
7
100 100
NUMBER OF ACTIVE OUTPUT
0 0
0 20 40 60 80 DC 0 20 40 60 80 100 DC
5/8
ULN2001A - ULN2002A - ULN2003A - ULN2004A
mm inch
DIM. OUTLINE AND
MIN. TYP. MAX. MIN. TYP. MAX. MECHANICAL DATA
a1 0.51 0.020
b 0.5 0.020
b1 0.25 0.010
D 20 0.787
E 8.5 0.335
e 2.54 0.100
e3 17.78 0.700
F 7.1 0.280
I 5.1 0.201
L 3.3 0.130
DIP16
Z 1.27 0.050
6/8
ULN2001A - ULN2002A - ULN2003A - ULN2004A
mm inch
DIM. OUTLINE AND
MIN. TYP. MAX. MIN. TYP. MAX. MECHANICAL DATA
A 1.75 0.069
a2 1.6 0.063
C 0.5 0.020
c1 45˚ (typ.)
e 1.27 0.050
e3 8.89 0.350
M 0.62 0.024
SO16 Narrow
S 8˚(max.)
(1) D and F do not include mold flash or protrusions. Mold flash or potrusions shall not exceed 0.15mm (.006inch).
7/8
ULN2001A - ULN2002A - ULN2003A - ULN2004A
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the conse-
quences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No
license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this
publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMi-
croelectronics products are not authorized for use as critical components in life support devices or systems without express written
approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
© 2002 STMicroelectronics – Printed in Italy – All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco -
Singapore - Spain - Sweden - Switzerland - United Kingdom - United States.
http://www.st.com
8/8
This datasheet has been downloaded from:
www.DatasheetCatalog.com
7 10
7B 7C
PRODUCTION DATA information is current as of publication date. Copyright 1993, Texas Instruments Incorporated
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Output C 7V
Output C
Input B Input B 10.5 kΩ
7.2 kΩ
E
7.2 kΩ 3 kΩ 3 kΩ E
ULN2001A ULN2002A
COM
RB
Output C
Input B
ULN2003A: RB = 2.7 kΩ
ULN2004A: RB = 10.5 kΩ 7.2 kΩ 3 kΩ E
ULN2003A, ULN2004A
All resistor values shown are nominal.
ICEX ICEX
Open VI
Open VCE
Open
II(off) IC
II(on)
VI Open
Open
IC Open
hFE =
II
II VCE IC
VI(on) VCE IC
VR
IR
VF IF
Open
Open
t PHL t PLH
50% 50%
Output
VOLTAGE WAVEFORMS
Input
Open 2 mH
ULN2001A only 1N3064
2.7 kΩ 200 Ω
Pulse
Generator Output
(see Note A) ULN2002A
ULN2003A CL = 15 pF
ULN2004A (see Note B)
TEST CIRCUIT
≤ 5 ns ≤ 10 ns
VIH
Input 90% 90% (see Note C)
1.5 V 1.5 V
10% 10%
40 µs 0V
VOH
Output
VOL
VOLTAGE WAVEFORMS
NOTES: A. The pulse generator has the following characteristics: PRR = 12.5 kHz, ZO = 50 Ω.
B. CL includes probe and jig capacitance.
C. For testing the ULN2001A and the ULN2003A, VIH = 3 V; for the ULN2002A, VIH = 13 V;
for the ULN2004A, VIH = 8 V.
TYPICAL CHARACTERISTICS
COLLECTOR-EMITTER COLLECTOR-EMITTER
SATURATION VOLTAGE SATURATION VOLTAGE
vs vs
COLLECTOR CURRENT TOTAL COLLECTOR CURRENT
(ONE DARLINGTON) (TWO DARLINGTONS PARALLELED)
2.5 2.5
TA = 25°C TA = 25°C
II = 250 µA
2 2
II = 250 µA II = 350 µA
II = 350 µA
1.5 II = 500 µA 1.5
II = 500 µA
1 1
0.5 0.5
VCE(sat)
VCE(sat)
0 0
0 100 200 300 400 500 600 700 800 0 100 200 300 400 500 600 700 800
IC – Collector Current – mA IC(tot) – Total Collector Current – mA
Figure 11 Figure 12
COLLECTOR CURRENT
vs
INPUT CURRENT
500
RL = 10 Ω
450
TA = 25°C
C – Collector Current – mA
400
VS = 10 V
350
VS = 8 V
300
250
200
150
IIC
100
50
0
0 25 50 75 100 125 150 175 200
II – Input Current – µA
Figure 13
THERMAL INFORMATION
D PACKAGE N PACKAGE
MAXIMUM COLLECTOR CURRENT MAXIMUM COLLECTOR CURRENT
vs vs
DUTY CYCLE DUTY CYCLE
600 600
C – Maximum Collector Current – mA
Figure 14 Figure 15
APPLICATION INFORMATION
1 16 1 16
2 15 2 15
3 14 3 14
4 13 4 13
5 12 5 12
6 11 6 11
7 10 7 10
P-MOS
Output 8 9 8 9
Lamp
TTL Test
Output
1 16 1 16
2 15 2 15
14 14
3 RP 3
4 13 4 13
5 12 5 12
6 11 6 11
7 10 7 10
8 9 8 9
CMOS
Output
TTL
Output
Figure 18. Buffer for Higher Current Loads Figure 19. Use of Pullup Resistors to
Increase Drive Current
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
www.DatasheetCatalog.com
7 10
7B 7C
PRODUCTION DATA information is current as of publication date. Copyright 1993, Texas Instruments Incorporated
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Output C 7V
Output C
Input B Input B 10.5 kΩ
7.2 kΩ
E
7.2 kΩ 3 kΩ 3 kΩ E
ULN2001A ULN2002A
COM
RB
Output C
Input B
ULN2003A: RB = 2.7 kΩ
ULN2004A: RB = 10.5 kΩ 7.2 kΩ 3 kΩ E
ULN2003A, ULN2004A
All resistor values shown are nominal.
ICEX ICEX
Open VI
Open VCE
Open
II(off) IC
II(on)
VI Open
Open
IC Open
hFE =
II
II VCE IC
VI(on) VCE IC
VR
IR
VF IF
Open
Open
t PHL t PLH
50% 50%
Output
VOLTAGE WAVEFORMS
Input
Open 2 mH
ULN2001A only 1N3064
2.7 kΩ 200 Ω
Pulse
Generator Output
(see Note A) ULN2002A
ULN2003A CL = 15 pF
ULN2004A (see Note B)
TEST CIRCUIT
≤ 5 ns ≤ 10 ns
VIH
Input 90% 90% (see Note C)
1.5 V 1.5 V
10% 10%
40 µs 0V
VOH
Output
VOL
VOLTAGE WAVEFORMS
NOTES: A. The pulse generator has the following characteristics: PRR = 12.5 kHz, ZO = 50 Ω.
B. CL includes probe and jig capacitance.
C. For testing the ULN2001A and the ULN2003A, VIH = 3 V; for the ULN2002A, VIH = 13 V;
for the ULN2004A, VIH = 8 V.
TYPICAL CHARACTERISTICS
COLLECTOR-EMITTER COLLECTOR-EMITTER
SATURATION VOLTAGE SATURATION VOLTAGE
vs vs
COLLECTOR CURRENT TOTAL COLLECTOR CURRENT
(ONE DARLINGTON) (TWO DARLINGTONS PARALLELED)
2.5 2.5
TA = 25°C TA = 25°C
II = 250 µA
2 2
II = 250 µA II = 350 µA
II = 350 µA
1.5 II = 500 µA 1.5
II = 500 µA
1 1
0.5 0.5
VCE(sat)
VCE(sat)
0 0
0 100 200 300 400 500 600 700 800 0 100 200 300 400 500 600 700 800
IC – Collector Current – mA IC(tot) – Total Collector Current – mA
Figure 11 Figure 12
COLLECTOR CURRENT
vs
INPUT CURRENT
500
RL = 10 Ω
450
TA = 25°C
C – Collector Current – mA
400
VS = 10 V
350
VS = 8 V
300
250
200
150
IIC
100
50
0
0 25 50 75 100 125 150 175 200
II – Input Current – µA
Figure 13
THERMAL INFORMATION
D PACKAGE N PACKAGE
MAXIMUM COLLECTOR CURRENT MAXIMUM COLLECTOR CURRENT
vs vs
DUTY CYCLE DUTY CYCLE
600 600
C – Maximum Collector Current – mA
Figure 14 Figure 15
APPLICATION INFORMATION
1 16 1 16
2 15 2 15
3 14 3 14
4 13 4 13
5 12 5 12
6 11 6 11
7 10 7 10
P-MOS
Output 8 9 8 9
Lamp
TTL Test
Output
1 16 1 16
2 15 2 15
14 14
3 RP 3
4 13 4 13
5 12 5 12
6 11 6 11
7 10 7 10
8 9 8 9
CMOS
Output
TTL
Output
Figure 18. Buffer for Higher Current Loads Figure 19. Use of Pullup Resistors to
Increase Drive Current
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
www.DatasheetCatalog.com
7 10
7B 7C
PRODUCTION DATA information is current as of publication date. Copyright 1993, Texas Instruments Incorporated
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Output C 7V
Output C
Input B Input B 10.5 kΩ
7.2 kΩ
E
7.2 kΩ 3 kΩ 3 kΩ E
ULN2001A ULN2002A
COM
RB
Output C
Input B
ULN2003A: RB = 2.7 kΩ
ULN2004A: RB = 10.5 kΩ 7.2 kΩ 3 kΩ E
ULN2003A, ULN2004A
All resistor values shown are nominal.
ICEX ICEX
Open VI
Open VCE
Open
II(off) IC
II(on)
VI Open
Open
IC Open
hFE =
II
II VCE IC
VI(on) VCE IC
VR
IR
VF IF
Open
Open
t PHL t PLH
50% 50%
Output
VOLTAGE WAVEFORMS
Input
Open 2 mH
ULN2001A only 1N3064
2.7 kΩ 200 Ω
Pulse
Generator Output
(see Note A) ULN2002A
ULN2003A CL = 15 pF
ULN2004A (see Note B)
TEST CIRCUIT
≤ 5 ns ≤ 10 ns
VIH
Input 90% 90% (see Note C)
1.5 V 1.5 V
10% 10%
40 µs 0V
VOH
Output
VOL
VOLTAGE WAVEFORMS
NOTES: A. The pulse generator has the following characteristics: PRR = 12.5 kHz, ZO = 50 Ω.
B. CL includes probe and jig capacitance.
C. For testing the ULN2001A and the ULN2003A, VIH = 3 V; for the ULN2002A, VIH = 13 V;
for the ULN2004A, VIH = 8 V.
TYPICAL CHARACTERISTICS
COLLECTOR-EMITTER COLLECTOR-EMITTER
SATURATION VOLTAGE SATURATION VOLTAGE
vs vs
COLLECTOR CURRENT TOTAL COLLECTOR CURRENT
(ONE DARLINGTON) (TWO DARLINGTONS PARALLELED)
2.5 2.5
TA = 25°C TA = 25°C
II = 250 µA
2 2
II = 250 µA II = 350 µA
II = 350 µA
1.5 II = 500 µA 1.5
II = 500 µA
1 1
0.5 0.5
VCE(sat)
VCE(sat)
0 0
0 100 200 300 400 500 600 700 800 0 100 200 300 400 500 600 700 800
IC – Collector Current – mA IC(tot) – Total Collector Current – mA
Figure 11 Figure 12
COLLECTOR CURRENT
vs
INPUT CURRENT
500
RL = 10 Ω
450
TA = 25°C
C – Collector Current – mA
400
VS = 10 V
350
VS = 8 V
300
250
200
150
IIC
100
50
0
0 25 50 75 100 125 150 175 200
II – Input Current – µA
Figure 13
THERMAL INFORMATION
D PACKAGE N PACKAGE
MAXIMUM COLLECTOR CURRENT MAXIMUM COLLECTOR CURRENT
vs vs
DUTY CYCLE DUTY CYCLE
600 600
C – Maximum Collector Current – mA
Figure 14 Figure 15
APPLICATION INFORMATION
1 16 1 16
2 15 2 15
3 14 3 14
4 13 4 13
5 12 5 12
6 11 6 11
7 10 7 10
P-MOS
Output 8 9 8 9
Lamp
TTL Test
Output
1 16 1 16
2 15 2 15
14 14
3 RP 3
4 13 4 13
5 12 5 12
6 11 6 11
7 10 7 10
8 9 8 9
CMOS
Output
TTL
Output
Figure 18. Buffer for Higher Current Loads Figure 19. Use of Pullup Resistors to
Increase Drive Current
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
www.DatasheetCatalog.com