Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
UNIVERSIDAD DE CUNDIANAMARCA
HIDRAULICA
DIMENSIONAMIENTO DE UNA RED DE TUBERÍAS
RESUMEN
Este trabajo fue realizado con la finalidad de crear un red de tubería capaz de trasportar un caudal de 1656
m3 *h-1 distribuido en 5 puntos de demanda ubicados a diferentes distancias y alturas piezométricas, para
esto se hace necesario el trazado de las tuberías teniendo en cuenta que cada una de ellas debe tener en el
balance de continuidad por lo menos dos caudales de entrada y uno de salida con el fin de garantizar el
abastecimiento del punto de demanda si una de las tuberías llega a tener una afectación. Debido a la
complejidad del dimensionamiento, la determinación de los caudales y las alturas piezométricas se realizó
mediante una metodología de matriz numérica. Este proyecto contenía una segunda fase la cual consistía en
el cálculo del costo del arreglo (incluye tubería, accesorios y arreglo de bomba), en esta fase fue fundamental
tener en cuenta el diámetro en función del costo; por último, se realizaron los cálculos correspondientes para
evitar la cavitación en los puntos donde se ubicaron las bombas.
PALABRAS CLAVE: DIMENSIONAMIENTO, CAUDAL, COSTOS DE INFRAESTRUCTURA
ABSTRACT
This work was realized by the purpose of creating a red of capable pipeline of transport a flow of 1656 m3 *h-
1 distributed in 5 points of demand located to different distances and piezometreical heights, for this the tracing
of the pipelines becomes necessary bearing in mind that each of them must have in the balance sheet of
continuity at least two flows of entry and one of exit in order guarantees the supply of the point of demand if
one of the pipelines manages to have an affectation. Due to the complexity of the
sizing, the determination of the flows and the piezometreical heights it was realized by means of a methodology
of numerical counterfoil. This project was containing the second phase which was consisting of the calculation
of the cost of the arrangement (it includes pipeline, accessories, and arrangement of pump), in this phase it
was fundamental bear the diameter in mind depending on the cost; finally the corresponding calculations were
realized to avoid the cavitation in the points where the pumps were located.
KEY WORDS: DIMENSIONING, FLOW, COSTS OF INFRASTRUCTURE
1
UNIVERSIDAD DE CUNDINAMARCA 2018
1. ALGORITMO DE SOLUCION
2
UNIVERSIDAD DE CUNDINAMARCA 2018
3
UNIVERSIDAD DE CUNDINAMARCA 2018
ALT- PIEZ P-ABS P-2 P-4 P-5 P-41 P-30 P-32 P-38 P-33 P-59 P-58 P-46
P-1
Hb 192.824179 991401.9521 P-3
Hc 194.377564 1036025.127 P-18 E-5 E-41 E-34
E-1 E-11 E-14 E-19 E-26 E-24 E-21 E-25 E-30
Hd 126.388351 418730.8391
He 131.86943 100045.4119 Ilustración 5 SEGUNDO ARREGLO DE BOMBAS
Hf 139.925077 345590.7525
Con 12 bombas en serie de referencia 250/410 se
Hg 121.292352 15990.0482
pudo producir el siguiente resultado:
Ilustración 2 ALTURAS PIEZOMETRICAS Y PRESION ABS
HP
donde se encontraban los puntos de demanda se 700
obtuvieron los siguientes resultados: 600
0 200 400 600 800
PRIMER ARREGLO: Ubicado en la tubería Q
#1 con una longitud total de 112 metros y un
hp calculado de 418 metros por lo que fue
necesario el siguiente arreglo de bombas: Ilustración 6 RAFICA DE ARREGLO #2
P-2 P-4 P-5 P-41 P-30 P-32 P-38 P-33 P-59 P-58 P-46 P-54 P-48 P-47 P-51 P-63 P-61 P-62 Según las consideraciones iniciales de las
características físico-químicas en este caso del agua
P-1
P-3 a 25° C, los intervalos para evitar cavitación son los
siguientes:
P-E-145P-18 E-5 E-11 E-14 E-19 E-26 E-24 E-21 E-25 E-30 E-41 E-34 E-43 E-31 E-42 E-44 E-35 E-45 E-47 E-46
4
UNIVERSIDAD DE CUNDINAMARCA 2018
COSTO K válvula
Al realizar la sumatoria de costos del
TUBERIA globo Te lineal
direccionamiento completo se obtuvo el siguiente
$ $ $
resultado:
553.867.413,02 27.530.252,20 46.112.716,80
Costo total del sistema
Ilustración 8 COSTO DE ACCESORIOS Y TUBERIAS
$ 1.444.549.849,66
Como el costo de tuberías se realizo por los 10
diferentes tramos y cada uno de estos contenía
Ilustración 12 COSTO TOTAL DEL SISTEMA
distinta longitud se obtuvo la siguiente gráfica:
$600,000,000.00
COSTO TUBERIA + ACCESORIOS POR SESIONES 4. DISCUSIÓN (O ANÁLISIS DE RESULTADOS)
$ 491.186.604,51
$ 814.240.373,26
5
UNIVERSIDAD DE CUNDINAMARCA 2018
5. CONCLUSION
6
UNIVERSIDAD DE CUNDINAMARCA 2018
Cálculo de presiones
ANEXO:
𝐿 8
𝑅 = (𝐹 + 𝛴𝐾) ∗ 2
𝐷 𝜋 ∗ 𝐷4 ∗ 𝑔 Tubería
Tee lineal
7
UNIVERSIDAD DE CUNDINAMARCA 2018
𝐶𝐵 = exp{9,2951 − 0,6019[𝑙𝑛(𝑆)]
997 ∗ 9,8 ∗ 0,46 ∗ 446
+ 0,0519[ln(𝑆)]2 } 𝑊𝑝1 =
0,8
𝐶𝐵 = exp{9,2951 − 0,6019[𝑙𝑛(0,78)]
+ 0,0519[ln(0,78)]2 } ∗ 3185 𝑊𝑝1 = 2509044
8
UNIVERSIDAD DE CUNDINAMARCA 2018
Cálculo de cavitación
Bomba 1
𝑃𝑎𝑡𝑚 − 𝑃𝑉 𝑣2
− 𝑁𝑃𝑆𝐻 − 𝛴𝑘
𝜌𝑔 2𝑔
𝑍=
𝑓 𝑣2
(1 + )
𝐷 2𝑔
101325 − 3168,43 0,78092
− 4,1 − 42,19 ∗
997 ∗ 9,81 2 ∗ 9,81
𝑍=
0,0143 0,78092
(1 + )
0,4 2 ∗ 9,81
𝑍 = 754,34
Bomba 2
𝑃𝑎𝑡𝑚 − 𝑃𝑉
− 𝑁𝑃𝑆𝐻 − ∆𝑍 𝐷
𝜌𝑔
𝐿= − − ∆𝑍
𝑣2 𝑓
( + 𝛴𝑘)
2𝑔
101325 − 3168,43
− 2,9 − 25 0,4
997 ∗ 9,81
𝐿= 2 − − 25
0,508 0,0156
( + 79,09)
2 ∗ 9,81
𝐿 = 14,409