Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Product Guide
Contents 1
Contents Page
Memguard MCBs 3
www.eaton.com
Memguard Introduction 2
The Memguard MCB distribution system, SPN or TPN, offers a wide 40A, 63A and 100A RCDs. These units are offered either as the main
range of thoroughly-proven outgoing and incoming device options incoming device or in conjunction with a main isolator.
for the control and protection of individual electrical sub-circuits in
industrial and commercial installations. Memguard offers a comprehensive range of distribution boards
covering the vast majority of specification requirements. All units are
Outgoing devices include: designed to the general requirements of BS5486: Part 12 specifications
3kA and 6kA SP, DP and TP MCBs with amperage ratings 10A-100A. for factory-built assemblies to ensure maximum protection to installer
and user in both domestic and industrial applications.
MCBs are available in the range of automatic plug in type for use in
Memguard distribution boards and custom-made equipment. The wide range of consumer units, distribution boards, and multipole
boards is constantly increasing, while continuous development has
3kA MCB/RCDs with amperage ratings 10A-40A and 30mA sensitivity. resulted in enclosures of more compact dimensions. All have been
This device can be used where both overload and earth fault designed for maximum convenience of wiring and fitting and embody
protection is required in a single unit, and has the advantage of only many benefits to increase electrical and mechanical efficiency,
occupying a single outgoing way on any Memguard distribution with extensive use of computer aided design and manufacturing
board. techniques.
Incoming devices include: Special care has been taken to ensure that the enclosures are clearly
100A DP or TP isolator which have a double break on each pole. labelled to aid installers and give end-users adequate guidance on
Access to the cabling terminations is easily achieved by the removal safety procedures. Circuit identification labels are fitted near the
of the snap-on protective cover. MCBs aperture and circuit wiring details are given inside the main
cover.
DESCRIPTION 32A 63A 100A
DP wire-in\wire-out Isolator SW250R/32 SW250R/63 SW250R
with interface barriers in top
RCDs can be used on their own or in conjunction with isolators to
give earth leakage protection to consumer units or multipole boards.
DP wire-in\wire-out Isolator SW250/32 - -
with interface barriers in bottom Finally, split busbar consumer units and multipole boards are offered
to allow the option of different RCD sensitivities on lighting and
TP wire-in\wire-out Isolator SW250/32 SW45/63 SW45
power/aircon circuits.
TP wire-in\wire-out to - SW46/63 SW46
Busbar Isolator
MCB incomer. 60A and 100A 3kA versions are available on both SPN
and TPN boards as standard. Again, other amperages and the higher
fault rated 6kA MCBs can be fitted on request.
www.eaton.com
Memguard MCBs
3
Eaton established range of 3kA MCBs is fully interchangeable. All Memguard MCBs have an over-centre handle mechanism which gives the
contacts a quick break action. The mechanism is also trip-free which ensures that the breaker cannot be held against a fault. Double and triple
pole breakers have an internal common trip mechanism as well as the handle tie bar.
When the circuit has operated under a short circuit or overload condition, the handle of the circuit breaker moves to the ‘MID’ position.To
reset, the handle must be switched to the ‘OFF’ position before switching ‘ON’ enabling the tripping latch mechanism to be reset.
Cable terminations provided are: 10A to 32A - 2 x 6mm2, 40A and 50A -16mm2, 63A - 25mm2, 80A and 100A - 50mm2.
Tested to BS3871 & also to UL 489 at 10kA breaking capacity 110 / 220V a.c. (NEMA AB1)
www.eaton.com
Memguard Residual Current Devices 4
An aspect of circuit protection that has Current Operated ELCB sensitivities. For example, the line diagram
seen increasing usage and awareness shows a 30mA sensitivity ELCB protecting
in recent years has been that of earth The Memguard range of ELCBs are of this power circuits and a 100mA sensitivity
fault protection through the use of earth type. They operate totally independently ELCB protecting lighting circuits.
fault circuit breakers known generally as of any earth path by monitoring currents
earth leakage circuit breakers (ELCBs) or flowing through the live and neutral
residual current devices (RCDs). supply. Any leakage to earth from either
live or neutral wires on the load side will
The use of circuit breakers or fuses to be recognised by the ELCB as an earth
protect the wiring installation against fault and the unit will trip very quickly to
short circuits, overloads, and earth faults isolate the supply.
of excessive levels which will cause the
protective device to operate have always They are therefore specified as additional
been a feature of Wiring Regulations. protection against electrocution and/or
However, it is a fact that earth faults fire resulting from heat generated in a
can be of sufficient magnitude to be faulty electrical installation.
hazardous to life and property whilst
being below the level that would cause The Role Of ELCBs
the protective device to trip.
The illustration shows the effect of
Types Of Earth Leakage Circuit continuous electrical current on the
Breaker human body. Duration of an electric shock
on the human body can be critical with
There are two basic forms of ELCB which current level and time being multiplying
detect faults by two totally different factors on the overall effect. Speed of Approx: 50mA and above
Ventricular fibrillation
methods: disconnection is therefore of utmost (where those signals which
importance and Eaton I MEM ELCBs will control heart operation are
disorientated by more
Voltage Operated ELCB Type detect and operate within 20ms to 40ms. powerful signals from
alternating current).
www.eaton.com
Memguard Residual Current Devices
5
RCDs Both Memguard single phase and multipole distribution boards are
available with the option of high performance RCDs in place of or in
Rating Sensitivity List No. List No. List No.
30mA 100mA 300mA
addition to incoming isolators. This is vital where it may be necessary
40A 2-pole AMM402H AMM402M AMM402L
to ensure a higher degree of protection against fire or shock risk than is
4-pole AMM404H AMM404M AMM404L
provided by the use of overcurrent devices alone, or to provide additional
earth leakage protection to one or more separate power circuits in a split
63A 2-pole AMM632H AMM632M AMM632L
phase board.
4-pole AMM634H AMM634M AMM634L
100A 2-pole AMM1002H AMM1002M AMM1002L
Our range of RCDs has been tested to IEC61008 and may be specified in
4-pole AMM1004H AMM1004M AMM1004L
40A and 63A double pole form for consumer units, and 40A, 63A and 100A
in 4-pole versions for multipole boards. Rated tripping currents (sensitivity)
for both types are 30mA, 100mA and 300mA. These sensitivities are easily
identified on the more common 40A and 63A units by following the colour
coding below:
30mA - Green
100mA -Red
300mA - Blue
www.eaton.com
Memguard Consumer Units 6
www.eaton.com
Memguard Consumer Units
7
Surface Version
Exposed Incomer (Incomer unit without cover)
Single Phase
No. of ways 4 6 8 10 12 14 16 20 24
100A DP Main Isolator 4DASS 6DASS 8DASS 10DASS 12DASS 14DASS 16DASS
60A DP MCB Incomer 4DAMS/60 6DAMS/60 8DAMS/60 10DAMS/60 12DAMS/60 14DAMS/60 16DAMS/60
100A DP MCB Incomer 4DAMS/100 6DAMS/100 8DAMS/100 10DAMS/100 12DAMS/100 14DAMS/100 16DAMS/100
40/63/100A DP RCD Main 4DAOS 6DAOS 8DAOS 10DAOS 12DAOS 14DAOS
Incomer
100A DP Main Isolator + 4DASOS 6DASOS 8DASOS 10DASOS 12DASOS
40/63/100A DP RCD
100A Terminal Incomer 6DAS 8DAS 10DAS 12DAS 14DAS 16DAS
Single Phase
No. of ways 4 6 8 10 12 14 16 20 24
100A DP Main Isolator CU4S CU6S CU8S CU10S CU12S CU14S CU16S
60A DP MCB Incomer CU4DS/60 CU6DS/60 CU8DS/60 CU10DS/60 CU12DS/60 CU14DS/60 CU16DS/60
100A DP MCB Incomer CU4DS/100 CU6DS/100 CU8DS/100 CU10DS/100 CU12DS/100 CU14DS/100 CU16DS/100
40/63/100A DP RCD Main ECU4XS ECU6XS ECU8XS ECU10XS ECU12XS ECU14XS
Incomer
100A DP Main Isolator + ECU4SXS ECU6SXS ECU8SXS ECU10SXS ECU12SXS
40/63/100A DP RCD
100A Terminal Incomer SD6S SD8S SD10S SD12S SD14S SD16S
www.eaton.com
Memguard Consumer Units 8
No. of List No. Dimension A KNOCKOUTS: Top/Bottom Back (approx.) Weight (approx.)
ways (mm) 34MM DIA 20.5mm dia. 90 x 25mm kg
6 6DAS 227 1 4 2 1.8
8 8DAS 278 1 6 2 2.0
10 10DAS 329 1 7 2 2.2
12 12DAS 380 1 8 2 2.4
14 14DAS 431 1 10 4 2.7
16 16DAS 482 1 12 4 3.0
Dimensions
B = 208mm
C = 93mm
All above consumer units are with knockout 3 x 26.5mm on left/right side.
www.eaton.com
Memguard Consumer Units
9
Dimensions
B = 208mm
C = 93mm
All above consumer units are with knockout 3 x 26.5mm on left/right side.
www.eaton.com
Memguard Consumer Units 10
List numbers for the surface mounted units shown here use the
suffix’S’. To order flush mounted, change the suffix S to F, i.e. 4DAOF.
All unused ways must be sealed with a blanking plate 1DCBP.
Dimensions B = 208mm
C = 93mm
www.eaton.com
Memguard Consumer Units
11
Flush Version
Exposed Incomer (Incomer unit without cover)
Single Phase
No. of ways 4 6 8 10 12 14 16 20 24
100A DP Main Isolator 4DASF 6DASF 8DASF 10DASF 12DASF 14DASF 16DASF
60A DP MCB Incomer 4DAMF/60 6DAMF/60 8DAMF/60 10DAMF/60 12DAMF/60 14DAMF/60 16DAMF/60
100A DP MCB Incomer 4DAMF/100 6DAMF/100 8DAMF/100 10DAMF/100 12DAMF/100 14DAMF/100 16DAMF/100
40/63/100A DP RCD Main 4DAOF 6DAOF 8DAOF 10DAOF 12DAOF 14DAOF
Incomer
100A DP Main Isolator + 4DASOF 6DASOF 8DASOF 10DASOF 12DASOF
40/63/100A DP RCD
100A Terminal Incomer 6DAF 8DAF 10DAF 12DAF 14DAF 16DAF
Single Phase
No. of ways 4 6 8 10 12 14 16 20 24
100A DP Main Isolator CU4F CU6F CU8F CU10F CU12F CU14F CU16F
60A DP MCB Incomer CU4DF/60 CU6DF/60 CU8DF/60 CU10DF/60 CU12DF/60 CU14DF/60 CU16DF/60
100A DP MCB Incomer CU4DF/100 CU6DF/100 CU8DF/100 CU10DF/100 CU12DF/100 CU14DF/100 CU16DF/100
40/63/100A DP RCD Main ECU4XF ECU6XF ECU8XF ECU10XF ECU12XF ECU14XF
Incomer
100A DP Main Isolator + ECU4SXF ECU6SXF ECU8SXF ECU10SXF ECU12SXF
40/63/100A DP RCD
100A Terminal Incomer SD6F SD8F SD10F SD12F SD14F SD16F
www.eaton.com
Memguard Consumer Units 12
No. of List No. Dimension A KNOCKOUTS: Top/Bottom Back (approx.) Weight (approx.)
ways (mm) 34MM DIA 20.5mm dia. 90 x 25mm kg
6 6DAF 247 1 4 2 1.8
8 8DAF 298 1 6 2 2.0
10 10DAF 349 1 7 2 2.2
12 12DAF 400 1 8 2 2.4
14 14DAF 451 1 10 4 2.7
16 16DAF 502 1 12 4 3.0
Dimensions
B = 227mm
C = 93mm
All above consumer units are with knockout 3 x 26.5mm on left/right side.
www.eaton.com
Memguard Consumer Units
13
Dimensions
B = 227mm
C = 93mm
All above consumer units are with knockout 3 x 26.5mm on left/right side.
www.eaton.com
Memguard Consumer Units 14
List numbers for the surface mounted units shown here use the
suffix’S’. To order flush mounted, change the suffix S to F, i.e. 4DAOF.
All unused ways must be sealed with a blanking plate 1DCBP.
Dimensions B = 227mm
C = 93mm
www.eaton.com
Memguard Distribution Boards
15
Surface Version
Multipole 3 Phase (Exposed Incomer)
No. of ways 4 6 8 10 12 14 16
100A TP Main Isolator 41DBSS 61DBSS 81DBSS 101DBSS 121DBSS 141DBSS 161DBSS
200A TP Main Isolator 42DBSS 62DBSS 82DBSS 102DBSS 122DBSS 142DBSS 162DBSS
60A TP MCB Incomer 4DBMS/60 6DBMS/60 8DBMS/60 10DBMS/60 12DBMS/60 14DBMS/60 16DBMS/60
100A TP MCB Incomer 4DBMS/100 6DBMS/100 8DBMS/100 10DBMS/100 12DBMS100 14DBMS/100 16DBMS/100
100A MCCB Incomer 41DBAS/100 61DBAS/100 81DBAS/100 101DBAS/100 121DBAS/100 141DBAS/100 161DBAS/100
160A MCCB Incomer 42DBAS/160 62DBAS/160 82DBAS/160 102DBAS/160 122DBAS/160 142DBAS160 162DBAS/160
200A MCCB Incomer 42DBAS/200 62DBAS/200 82DBAS/200 102DBAS/200 122DBAS/200 142DBAS/200 162DBAS/200
40/63A, 4-Pole RCD Main Incomer 4DBOS 6DBOS 8DBOS 10DBOS 12DBOS 14DBOS
100A, 4-Pole RCD Main Incomer 41DBOS 61DBOS 81DBOS 101DBOS 121DBOS 141DBOS 161DBOS
100A TP Main Isolator + 40/63A, 4-Pole RCD 4DBSOS 6DBSOS 8DBSOS 10DBSOS 12DBSOS 14DBSOS 16DBSOS
100A TP Main Isolator + 100A, 4-Pole RCD 41DBSOS 61DBSOS 81DBSOS 101DBSOS 121DBSOS 141DBSOS 161DBSOS
100A Terminal Incomer 41DBS 61DBS 81DBS 101DBS 121DBS 141DBS 161DBS
200A Terminal Incomer 42DBS 62DBS 82DBS 102DBS 122DBS 142DBS 162DBS
www.eaton.com
Memguard Distribution Boards 16
100A TP Main Isolator + 40/63A, 4-Pole RCD 221DBSOS/Q 421DBSOS/Q 441DBSOS/Q 641DBSOS/Q 661DBSOS/Q 861DBSOS/Q 1061DBSOS/Q
with MCB protection of upper split 841DBSOS/Q
100A TP Main Isolator + 2X40/63A, 4-Pole RCD 221DBSOOS 421DBSOOS 621DBSOOS 821DBSOOS 1021DBSOOS 1041DBSOOS 1061DBSOOS
241DBSOOS 441DBSOOS 641DBSOOS 841DBSOOS 861DBSOOS 6101DBSOOS
261DBSOOS 461DBSOOS 661DBSOOS 681DBSOOS 881DBSOOS
281DBSOOS 481DBSOOS 4101DBSOOS
210DBSOOS
200A TP Main Isolator + 2x40/63A, 4-Pole RCD 442DBSOOS 642DBSOOS 842DBSOOS 1042DBSOOS 1062DBSOOS
100A TP Main Isolator + 3x40/63A, 4-Pole RCD 2221DBSOOOS 4221DBSOOOS 4421DBSOOOS 6421DBSOOOS
100A TP Main Isolator + 4x40/63A, 4-Pole RCD 2222DBSOOOOS 42221DBSOOOOS 44221DBSOOOOS 64221DBSOOOOS
100A TP Main Isolator + 40/63A, 4-Pole RCD DB22BXS/Q DB42BXS/Q DB44BXS/Q DB64BXS/Q DB66BXS/Q DB86BXS/Q DB106BXS/Q
with MCB protection of upper split DB84BXS/Q
100A TP Main Isolator + 2x40/63A, 4-Pole RCD DB22BXXS DB42BXXS DB62BXXS DB82BXXS DB102BXXS DB104BXXS DB106BXXS
DB24BXXS DB44BXXS DB64BXXS DB84BXXS DB86BXXS DB610BXXS
DB26BXXS DB46BXXS DB66BXXS DB68BXXS DB88BXXS
DB28BXXS DB48BXXS DB410BXXS
DB210BXXS
200A TP Main Isolator + 2x40/63A, 4-Pole RCD DB44CXXS DB64CXXS DB84CXXS DB104CXXS DB106CXXS
100A TP Main Isolator + 3x40/63A, 4-Pole RCD DB222BXXXS DB422BXXXS DB442BXXXS DB642BXXXS
100A TP Main Isolator + 4x40/63A, 4-Pole RCD DB2222BXXXXS DB4222BXXXXS DB4422BXXXXS DB6422BXXXXS
www.eaton.com
Memguard Distribution Boards
17
200A TP Main Isolator 100A TP Main Isolator 40A or 63A 4-Pole RCD*
List No. Weight List No. Weight
No. of Dimension Dimension No. of Dimension Dimension
Enclosed Exposed (approx.) Enclosed Exposed (approx.)
ways A (mm) C (mm) ways A (mm) C (mm)
Incomer Incomer kg Incomer Incomer kg
4 M12CS 42DBSS 626 128 10.6 4 M12BXS 4DBSOS 473 128 7.5
6 M18CS 62DBSS 703 128 11.8 6 M18BXS 6DBSOS 550 128 8.5
8 M24CS 82DBSS 779 128 13.1 8 M24BXS 8DBSOS 626 128 10.0
10 M30CS 102DBSS 856 128 15.8 10 M30BXS 10DBSOS 703 128 10.7
12 M36CS 122DBSS 932 128 16.8 12 M36BXS 12DBSOS 779 128 11.7
14 M42CS 142DBSS 1009 128 17.7 14 M42BXS 14DBSOS 856 128 13.0
16 M48CS 162DBSS 1085 128 18.8 16 M48BXS 16DBSOS 932 128 14.0
Dimensions Knockouts
B = 366mm
C = 109mm
Unless listed in tables
www.eaton.com
Memguard Distribution Boards 18
www.eaton.com
Memguard Distribution Boards
19
The split busbar arrangement allows separation of circuit groups. 100A TP MAIN ISOLATOR and
Up to four busbars can be fed by individual RCDs to allow different 40A OR 63A 4-POLE RCD*
ratings and protection levels on each circuit group. In each case an No. of ways Weight
integral main switch is fitted for isolation of all circuits. List Dimension
(approx.)
RCD RCD No. A (mm)
kg
(1) (2)
Contact your regional office for details of products to suit 2 2 DB22BXXS 550 9.5
applications requiring more than 4 split busbars. 4 2 DB42BXXS 626 10.5
2 4 DB24BXXS 626 10.5
The first number in the catalogue reference refers to the lower 6 2 DB62BXXS 703 11.5
busbar section and the subsequent numbers refer to the progressive 4 4 DB44BXXS 703 11.5
levels upwards. 2 6 DB26BXXS 703 11.5
8 2 DB82BXXS 779 12.3
The units have provision for Eaton RCDs (see pages 4-5) which can 6 4 DB64BXXS 779 12.3
be factory mounted on request. 4 6 DB46BXXS 779 12.3
2 8 DB28BXXS 779 12.3
10 2 DB102BXXS 856 13.8
Enclosed Incomer
8 4 DB84BXXS 856 13.8
100A TP MAIN ISOLATOR and
6 6 DB66BXXS 856 13.8
40A OR 63A 4-POLE RCD*
4 8 DB48BXXS 856 13.8
Switch RCD List Dimension Weight
Ways Ways No. A (mm) (approx.) kg 2 10 DB210BXXS 856 13.8
2 2 DB22BXS 550 9.0 10 4 DB104BXXS 932 14.5
4 2 DB42BXS 626 10.0 8 6 DB86BXXS 932 14.5
2 4 DB24BXS 626 10.0 6 8 DB68BXXS 932 14.5
6 2 DB62BXS 703 11.2 4 10 DB410BXXS 932 14.5
4 4 DB44BXS 703 11.2 10 6 DB106BXXS 1009 15.3
2 6 DB26BXS 703 11.2 6 10 DB610BXXS 1009 15.3
8 2 DB82BXS 779 12.0 8 8 DB88BXXS 1009 15.3
6 4 DB64BXS 779 12.0
100A TP MAIN ISOLATOR and
4 6 DB46BXS 779 12.0 40A OR 63A 4-POLE RCD*
2 8 DB28BXS 779 12.0 No. of ways Weight
List Dimension
10 2 DB102BXS 856 13.5 RCD RCD (approx.)
No. A (mm)
8 4 DB84BXS 856 13.5 (1) (2) kg
6 6 DB66BXS 856 13.5 4 4 DB44CXXS 1009 10.5
4 8 DB48BXS 856 13.5 6 4 DB64CXXS 1085 11.0
2 10 DB210BXS 856 13.5 Other configurations available to special order
10 4 DB104BXS 932 14.3
100A TP MAIN ISOLATOR and
8 6 DB86BXS 932 14.3 3 x 40A OR 63A 4-POLE RCDs*
6 8 DB68BXS 932 14.3 No. of ways Weight
4 10 DB410BXS 932 14.3 List Dimension
RCD RCD RCD (approx.)
No. A (mm)
10 6 DB106BXS 1009 15.5 (1) (2) (3) kg
6 10 DB610BXS 1009 15.5 4 2 2 DB422BXXXS 932 11.0
8 8 DB88BXS 1009 15.5 4 4 2 DB442BXXXS 1009 11.5
6 4 2 DB642BXXXS 1085 12.0
Dimensions Knockouts
Other configurations available to special order
www.eaton.com
Memguard Distribution Boards 20
Dimensions
Knockouts 200A TP MAIN ISOLATOR and 2 x 40A or
63A 4-POLE RCDs*
No. of ways
All multipole boards are fitted with List Dimension Weight
top and bottom semi-knockouts are RCD RCD No. A (mm) (approx.) kg
(1) (2)
follows:
4 4 442DBSOOS 1009 10.2
www.eaton.com
Memguard Distribution Boards
21
Split Busbar Multipole Distribution Boards Distribution Boards For Non-standard Applications
(TPN 40/63/100/160/200A, 415V AC)
The product illustrated below incorporates two multipole busbar The unique design of Viscount allows many non-standard
sections, the lower being fed direct from a main 100A isolator and arrangements of busbar systems and incoming devices to
the upper busbar being fed via a triple-pole MCB and four-pole be produced to meet specific customer requirements. One
RCD to provide combined earth leakage and overall overcurrent of the more frequently specified derivatives is shown below
protection. and serves as an excellent example of the level of complexity
which can be achieved in the Viscount product range.
List No. Multipole Dimension (mm)
ways Weight Other products available typically combine MCB or MCCB
Lower (approx.) incomers with RCDs to provide overcurrent and earth fault
Enclosed Exposed and Upper kg
Height Width Depth protection. For areas where high prospective fault currents
Incomer Incomer Section
can occur, the inclusion of HRC fuselinks in the incoming
DB22BXS/Q 221DBSOS/Q 2+2 550 366 109 9.4 section of the board can provide back-up protection for fault
DB42BXS/Q 421DBSOS/Q 4+2 626 366 109 10.9 levels of up to 16kA.
DB44BXS/Q 441DBSOS/Q 4+4 703 366 109 11.6
DB64BXS/Q 641DBSOS/Q 6+4 779 366 109 12.4
DB66BXS/Q 661DBSOS/Q 6+6 856 366 109 13.1
DB86BXS/Q 861DBSOS/Q 8+6 932 366 109 13.8
DB106BXS/Q 1061DBSOS/Q 10+6 1009 366 109 15.2
www.eaton.com
Memguard Distribution Boards 22
• RCD available in 40A, 63A or 100A ratings, 30mA, 100mA or 300mA sensitivity. See page 5 for ordering
system.
• Multipole distribution boards (3phase, 4wire) will accept combinations of SP, DP or TP plug-in MCBs as
shown on page 3.
• Multipole distribution boards are type tested on BS5486: Part 12:1979.
• Ingress protection category of enclosure is IP30.
• 41/51mm dia. incoming knockout provided along with 1 off 33mm, 1 off 26mm and 8 off 21mm dia.
outgoing conduit knockout are available at each end of all enclosure sizes.
• 100A terminal incomer DB has 50mm2 incoming cable capacity.
• 200A terminal incomer DB has 150mm2 incoming cable capacity.
• 100A TP main switch has AC21 duty to IEC60947-3 (BSEN60947-3) and cable capacity of 50mm2.
• 200A TP switch disconnector has AC21 duty to IEC60947-3 and a cable capacity of 95mm2.
• 100A G-frame MCCB incomer is type tested to IEC60947-2 and has 70mm2 cable capacity.
• 160A and 200A F-frame MCCB incomers are type tested to IEC60947-2 and have a cable capacity of
95mm2.
• 40A, 63A and 100A 4P RCDs have 25mm2 cable capacity.
• 60A and 100A DP MCB incomers have 50mm2 cable capacity.
• Neutral bar has 50mm2 incoming cable termination along with a 16mm2 outgoing terminal for each
outgoing MCB.
• An earth bar is supplied for the outgoing MCB ways in addition to a main earth terminal stud.
• Each unused SP outgoing way must be sealed with a blanking plate 1 DCBP.
• The list numbers used above relate to surface mounted boards. Should a flush mounted unit be
required then the suffix S should be changed to F, i.e. 41DBSS becomes 41DBSF for a flush version.
• Available in RAL7004 with epoxy coating.
Flush Version
Multipole 3 Phase (Exposed Incomer)
No. of ways 4 6 8 10 12 14 16
100A TP Main Isolator 41DBSF 61DBSF 81DBSF 101DBSF 121DBSF 141DBSF 161DBSF
200A TP Main Isolator 42DBSF 62DBSF 82DBSF 102DBSF 122DBSF 142DBSF 162DBSF
60A TP MCB Incomer 4DBMF/60 6DBMF/60 8DBMF/60 10DBMF/60 12DBMF/60 14DBMF/60 16DBMF/60
100A TP MCB Incomer 4DBMF/100 6DBMF/100 8DBMF/100 10DBMF/100 12DBMF/100 14DBMF/100 16DBMF/100
100A MCCB Incomer 41DBAF/100 61DBAF/100 81DBAF/100 101DBAF/100 121DBAF/100 141DBAF/100 161DBAF/100
160A MCCB Incomer 42DBAF/160 62DBAF/160 82DBAF/160 102DBAF/160 122DBAF/160 142DBAF/160 162DBAF/160
200A MCCB Incomer 42DBAF/200 62DBAF/200 82DBAF/200 102DBAF/200 122DBAF/200 142DBAF/200 162DBAF/200
40/63A, 4-Pole RCD Main Incomer 4DBOF 6DBOF 8DBOF 10DBOF 12DBOF 14DBOF
100A, 4-Pole RCD Main Incomer 41DBOF 61DBOF 81DBOF 101DBOF 121DBOF 141DBOF 161DBOF
100A TP Main Isolator + 40/63A, 4-Pole RCD 4DBSOF 6DBSOF 8DBSOF 10DBSOF 12DBSOF 14DBSOF 16DBSOF
100A TP Main Isolator + 100A, 4-Pole RCD 41DBSOF 61DBSOF 81DBSOF 101DBSOF 121DBSOF 141DBSOF 161DBSOF
100A Terminal Incomer 41DBF 61DBF 81DBF 101DBF 121DBF 141DBF 161DBF
200A Terminal Incomer 42DBF 62DBF 82DBF 102DBF 122DBF 142DBF 162DBF
www.eaton.com
Memguard Distribution Boards
23
100A TP Main Isolator + 40/63A, 4-Pole RCD 221DBSOF/Q 421DBSOF/Q 441DBSOF/Q 641DBSOF/Q 661DBSOF/Q 861DBSOF/Q 1061DBSOF/Q
with MCB protection of upper split 841DBSOF/Q
100A TP Main Isolator + 2X40/63A, 4-Pole RCD 221DBSOOF 421DBSOOF 621DBSOOF 821DBSOOF 1021DBSOOF 1041DBSOOF 1061DBSOOF
241DBSOOF 441DBSOOF 641DBSOOF 841DBSOOF 861DBSOOF 6101DBSOOF
261DBSOOF 461DBSOOF 661DBSOOF 681DBSOOF 881DBSOOF
281DBSOOF 481DBSOOF 4101DBSOOF
210DBSOOF
200A TP Main Isolator + 2x40/63A, 4-Pole RCD 442DBSOOF 642DBSOOF 842DBSOOF 1042DBSOOF 1062DBSOOF
100A TP Main Isolator + 3x40/63A, 4-Pole RCD 2221DBSOOOF 4221DBSOOOF 4421DBSOOOF 6421DBSOOOF
100A TP Main Isolator + 4x40/63A, 4-Pole RCD 2222DBSOOOOF 42221DBSOOOOF 44221DBSOOOOF 64221DBSOOOOF
100A TP Main Isolator + 40/63A, 4-Pole RCD DB22BXF/Q DB42BXF/Q DB44BXF/Q DB64BXF/Q DB66BXF/Q DB86BXF/Q DB106BXF/Q
with MCB protection of upper split DB84BXF/Q
100A TP Main Isolator + 2x40/63A, 4-Pole RCD DB22BXXF DB42BXXF DB62BXXF DB82BXXF DB102BXXF DB104BXXF DB106BXXF
DB24BXXF DB44BXXF DB64BXXF DB84BXXF DB86BXXF DB610BXXF
DB26BXXF DB46BXXF DB66BXXF DB68BXXF DB88BXXF
DB28BXXF DB48BXXF DB410BXXF
DB210BXXF
200A TP Main Isolator + 2x40/63A, 4-Pole RCD DB44CXXF DB64CXXF DB84CXXF DB104CXXF DB106CXXF
100A TP Main Isolator + 3x40/63A, 4-Pole RCD DB222BXXXF DB422BXXXF DB442BXXXF DB642BXXXF
100A TP Main Isolator + 4x40/63A, 4-Pole RCD DB2222BXXXXF DB4222BXXXXF DB4422BXXXXF DB6422BXXXXF
www.eaton.com
Memguard Distribution Boards 24
200A TP Main Isolator 100A TP Main Isolator 40A or 63A 4-Pole RCD*
List No. Weight List No. Weight
No. of Dimension Dimension No. of Dimension Dimension
Enclosed Exposed (approx.) Enclosed Exposed (approx.)
ways A (mm) C (mm) ways A (mm) C (mm)
Incomer Incomer kg Incomer Incomer kg
4 M12CF 42DBSF 657 128 10.6 4 M12BXF 4DBSOF 504 128 7.5
6 M18CF 62DBSF 733 128 11.8 6 M18BXF 6DBSOF 580 128 8.5
8 M24CF 82DBSF 810 128 13.1 8 M24BXF 8DBSOF 657 128 10.0
10 M30CF 102DBSF 886 128 15.8 10 M30BXF 10DBSOF 733 128 10.7
12 M36CF 122DBSF 963 128 16.8 12 M36BXF 12DBSOF 810 128 11.7
14 M42CF 142DBSF 1039 128 17.7 14 M42BXF 14DBSOF 886 128 13.0
16 M48CF 162DBSF 1116 128 18.8 16 M48BXF 16DBSOF 963 128 14.0
Dimensions Knockouts
B = 394mm
C = 109mm
Unless listed in tables
www.eaton.com
Memguard Distribution Boards
25
www.eaton.com
Memguard Distribution Boards 26
The split busbar arrangement allows separation of circuit groups. 100A TP MAIN ISOLATOR and
Up to four busbars can be fed by individual RCDs to allow different 40A OR 63A 4-POLE RCD*
ratings and protection levels on each circuit group. In each case an No. of ways Weight
integral main switch is fitted for isolation of all circuits. List Dimension
(approx.)
RCD RCD No. A (mm)
kg
(1) (2)
Contact your regional office for details of products to suit 2 2 DB22BXXF 580 9.5
applications requiring more than 4 split busbars. 4 2 DB42BXXF 657 10.5
2 4 DB24BXXF 657 10.5
The first number in the catalogue reference refers to the lower 6 2 DB62BXXF 733 11.5
busbar section and the subsequent numbers refer to the progressive 4 4 DB44BXXF 733 11.5
levels upwards. 2 6 DB26BXXF 733 11.5
8 2 DB82BXXF 810 12.3
The units have provision for Eaton RCDs (see pages 4-5) which can 6 4 DB64BXXF 810 12.3
be factory mounted on request. 4 6 DB46BXXF 810 12.3
2 8 DB28BXXF 810 12.3
10 2 DB102BXXF 886 13.8
Enclosed Incomer
8 4 DB84BXXF 886 13.8
100A TP MAIN ISOLATOR and
6 6 DB66BXXF 886 13.8
40A OR 63A 4-POLE RCD*
4 8 DB48BXXF 886 13.8
Switch RCD List Dimension Weight
Ways Ways No. A (mm) (approx.) kg 2 10 DB210BXXF 886 13.8
2 2 DB22BXF 580 9.0 10 4 DB104BXXF 963 14.5
4 2 DB42BXF 657 10.0 8 6 DB86BXXF 963 14.5
2 4 DB24BXF 657 10.0 6 8 DB68BXXF 963 14.5
6 2 DB62BXF 733 11.2 4 10 DB410BXXF 963 14.5
4 4 DB44BXF 733 11.2 10 6 DB106BXXF 1039 15.3
2 6 DB26BXF 733 11.2 6 10 DB610BXXF 1039 15.3
8 2 DB82BXF 810 12.0 8 8 DB88BXXF 1039 15.3
6 4 DB64BXF 810 12.0
100A TP MAIN ISOLATOR and
4 6 DB46BXF 810 12.0 40A OR 63A 4-POLE RCD*
2 8 DB28BXF 810 12.0 No. of ways Weight
List Dimension
10 2 DB102BXF 886 13.5 RCD RCD (approx.)
No. A (mm)
8 4 DB84BXF 886 13.5 (1) (2) kg
6 6 DB66BXF 886 13.5 4 4 DB44CXXF 1039 10.5
4 8 DB48BXF 886 13.5 6 4 DB64CXXF 1116 11.0
2 10 DB210BXF 886 13.5 Other configurations available to special order
10 4 DB104BXF 963 14.3
100A TP MAIN ISOLATOR and
8 6 DB86BXF 963 14.3 3 x 40A OR 63A 4-POLE RCDs*
6 8 DB68BXF 963 14.3 No. of ways Weight
4 10 DB410BXF 963 14.3 List Dimension
RCD RCD RCD (approx.)
No. A (mm)
10 6 DB106BXF 1039 15.5 (1) (2) (3) kg
6 10 DB610BXF 1039 15.5 4 2 2 DB422BXXXF 963 11.0
8 8 DB88BXF 1039 15.5 4 4 2 DB442BXXXF 1039 11.5
6 4 2 DB642BXXXF 1116 12.0
Dimensions Knockouts
Other configurations available to special order
www.eaton.com
Memguard Distribution Boards
27
www.eaton.com
There’s a certain energy at Eaton. It’s the power of uniting some
of the world’s most respected names to build a brand you can
trust to meet every power management need. The energy created
supports our commitment to powering business worldwide.
From power distribution to power quality and control, Eaton
allows you to proactively manage your complete power system
by providing electrical solutions that make your applications safer,
more reliable, and highly efficient. Visit www.eaton.com/electrical.
All of the above are trademarks of Eaton Corporation or its affiliates. Eaton has a
license to use the Westinghouse brand name in Asia Pacific. ©2009 Eaton Corporation.
Eaton is dedicated to ensuring that reliable, efficient and safe
power is available when it’s needed most. With unparalleled
knowledge of electrical power management across industries,
experts at Eaton deliver customized, integrated solutions to
solve our customers’ most critical challenges.
Our focus is on delivering the right solution for the application.
But, decision makers demand more than just innovative products.
They turn to Eaton for an unwavering commitment to personal
support that makes customer success a top priority. For more
information, visit www.eaton.com/seasia.