Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
I II
Staff readings 1.680 1.602
Eye piece end of bubble 20 10
Object glass end of bubble 10 20
OR
5.Differentiate between permanent and temporary adjustments of level? (10)
6) The following perpendicular offsets were taken from a chain line to a hedge:
Calculate the area between the survey line, the hedge and the end offsets by (a) Trapezoidal rule
(b) Simpson’s rule (5+5)
OR
7) A railway embankment 400 m long is 12 m wide at the formation level and has the side slope
2 to 1. The ground levels at every 100 m along the centre line are as under:
The formation level at zero chainage is 207.00 m and the embankment has a rising gradient of 1
in 100. The ground is level across the centre line. Calculate the volume of earthwork. (10)
8) Distinguish between L.S and C.S surveying? (5+5)
OR
9).(a)Write the general procedure for measuring the vertical angle by theodolite surveying?
(b) What is trigonometric leveling? (5+5)
10) The table below gives the lengths and bearings of the lines of a traverse ABCDE, the length
and bearing of EA having been omitted.
********
MRCET- Department of Mining Engineering Model Question Paper-2
a) If the reduced level of B is 55.18 m above the datum, what is the reduced level of A?
b) Assuming that the atmospheric conditions remain unchanged during the two sets of the
observations, calculate (i) the combined curvature and refraction correction if the distance AB is
315 m, and (ii) the collimation error. (5+5)
6.The following offsets were taken from a chain line to an irregular boundary line at an interval
of 10 m are 0, 2.50, 3.50, 5.00, 4.60, 3.20, 0 m. Compute the area between the chain line, the
irregular boundary line and the end offsets by:
a) Trapezoidal Rule
b) Simpson’s Rule (5+5)
OR
7.Compute the volume of earth work involved in constructing a farm pond of the following
size:
Size of the bottom: 6 x 4 m
Side slope: 2:1
Depth of pond: 4 m
Work out the cost of earth work also if it costs Rs. 50 per m3 (10)
OR
11.The whole circle bearings of the lines of a closed traverse are given below. Find the included
angles of the traverse. (10)
Line AB BC CD DA
Bearing 78048′20′′ 152031′40′′ 251018′40′′ 3044′15′′
********
MRCET- Department of Mining Engineering Model Question Paper-3
2.What is the principle of chain surveying?What are the different sources of errors in chain
surveying? (5+5)
OR
3.The distance between two points measured along a slope is 126 m Find the horizontal distance
between them if (a) the angle of slope between the points is 6030′ (b) the difference between the
level is 30 m (c) the slope is 1 in 4? (3+4+3)
4.(a)The reading taken on a staff 100 m from the instrument with the bubble central was 1.872m.
The bubble is then moved 5 divisions out of the centre and the staff reading is observed to be
1.906 m. Find the angular value of one division of the bubble and radius of curvature of the
bubble tube, The length of one division of the bubble is 2mm?
(b) Describing Reciprocal Levelling? (5+5)
OR
5.The following consecutive readings were taken with a level and 3 metre leveling staff on
continuously sloping ground at a common interval of 20 metres: 0.602, 1.234, 1.860, 2.574,
0.238, 0.914, 1.936, 2.872, 0.568, 1.824, 2.722.The reduced level of the first point was
192.122m. Rule out page field book and enter the above readings. Calculate the reduced levels of
the points and also the gradient of the line joining the first and the last points? (10)
6.The following table gives the corrected latitudes and departures (in metres) of the sides of a
closed traverse ABCD:
Compute the area by (i) M.D method, (ii) D.M.D method, (iii) Departure and total latitudes,
(iv).Co-ordinate method (5+5)
OR
7.A rectangular plot ABCD forms the plane of a pit excavated for road work. E is point of
intersection of the diagonals. Calculate the volume of the excavation in cubic metres from
the following data:
Point A B C D E
Original 45.2 49.8 51.2 47.2 52.0
Level
Final 38.6 39.8 42.6 40.8 42.5
Level
10.Distinguish between loose needle method and fast needle method in traversing? (10)
OR
11.The following interior angles were measured with a sextant in a closed traverse. The bearing
of the line AB was measured as 60000′ with prismatic compass Calculate the bearings of all other
line if angle A = 140010′, angle B = 9908′, angle C =60022′ .angle D = 69020′ (10)
********
SURFACE MINING TECHNOLOGY
MRCET- Department of Mining Engineering Model Question Paper-1
6) What is continuous method? Write the working principle of Bucket Wheel Excavator with
neat sketch along with the merits, demerits, capacity of the machine? (2+8)
OR
7) An opencast deposit having production is 2.5 MT /Annum with shovel –dumper combination.
Draw a layout of the mines by your own assumption as well as the man power required for
achieving the above target? (10)
8). (a) Describe the different conveying equipment are used for transporting the minerals in
opencast mines?
(b) Distinguish between hydraulic shovel and rope shovel? (5+5)
9).Write the different methodologies for doing the mechanized quarries over an underground
developed working zone? (10)
********
MRCET- Department of Mining Engineering Model Question Paper-2
6.A coal seam is at a depth of 200m from the surface having a thickness of 6 m. It is proposed to
work by opencast mining. Give the equipment and manpower required and the layout of the
opencast? (10)
OR
7) Explain the working principle of Continuous Surface Miner along with its layout and its
advantages and limitations? (10)
8. (a) Give the organizational structure of a large opencast project with shovel dumper
combination?
(b) Explain the preventive measures taken while working on already developed pillars through
opencast mining? (5+5)
OR
9.(a)How is spontaneous heating dealt in opencast mines in
(i)Coal yards
(ii) Existing pillars
(b) What are the preventive measures to be taken in the machinery of opencast mines? (5+5)
********
MRCET- Department of Mining Engineering Model Question Paper-3
6.Describe the working principle and operation of Dragline in a large opencast coal mine with
layout. Write the advantages, limitation, and capacity calculation of dragline? (10)
OR
7.(a) Describe the working principle of shovel with neat layout. Write the advantages and
disadvantages of shovel?
(b)Describe the operating parameters of the shovel? (5+5)
8. (a) A underground coal mine deposit having thickness 10 m is at a depth of 200 m has been
developed ? What are preventive steps to be taken to excavate the coal in opencast mechanized
method?
(b) Distinguish between cyclic method and continuous method? (5+5)
OR
9.Explain the design principle of large opencast mines? (10)
OR
11.What are the recent developments in the deployment of heavy earth moving machineries in
surface mining? (10)
********
MINE MECHANIZATION-I
MRCET- Department of Mining Engineering Model Question Paper-1
8. Name the different types of locomotives used in mines and compare locomotives with rope
haulages. Discuss, in detail, the construction and operation of any one type of locomotive
(including safety features).
OR
9. Discuss briefly about the belt conveyor construction with all its parts.
10. What are the types of drilling used for coal and stone? Describe the construction and working
principle of jack hammer drill.
OR
11. Why pneumatic drills are not used in coal mines? Describe the construction and working
principle of the coal drills used in mines.
********
MRCET- Department of Mining Engineering Model Question Paper-2
b) In a belt drive the belt is running at 20m/s transmits 5 kW power. If the permissible pull of the
belt is 15 N/ mm of width of belt, calculate the tension at the tight and slack side of the belt and
also the width of the belt required.Angle of lap= 1500, co-efficient of friction between belt and
pulley = 0.4
4. What safety devices are to be provided on the haulage roadways to prevent runaway of tubs?
Discuss briefly the construction and operation of each one of it with the help of diagrams.
OR
5. a) Describe about the Endless rope haulage used in mines.
b) A direct rope haulage 500 mtr long and 1 in 10 inclinations. Coal tubs haul up the road in the
set of 5 , using a rope of 18 mm diameter.. The tub has a tare weight of 500 kgf and capacity of
500 kgf of coal. What should be the weight of rope for the duty? Calculate the power of the
electric motor to work the haulage if the maximum speed of rope is 10 km/h. Friction for tub =
1/10 and friction for rope = 1/50.(The rope has constants as k= 0.36 and s= 52 kN/cm2)
6. Write briefly about the construction and working principle of aerial ropeway with its
individual parts?
OR
7. Write notes on:
a) Types of crossing with layout used in haulage track
b) Essentials of a good haulage track
10. What is rotary drilling? Describe the working principle of coal drills with its merits and
demerits.
OR
11. Write notes on:
a) Jack hammer drill
b) Jumbo drill
********
MRCET- Department of Mining Engineering Model Question Paper-3
OR
3. a) Describe the working principle of clutch.
b) A conveyor belt running at 500m/min transmits 5 kW. The angle of lap is 1600 and the
coefficient of friction between the belt and the pulley is 0.3. If the permissible pull in the belt is
16 Newton per mm width, calculate the tension on the driving side and the width of the belt
required.
6. Write briefly about the haulage track in a mine with the essentials for a good haulage track.
What are the types of joints and crossing used for haulage tracks?
OR
7. Answer all:
a) Discuss the construction of aerial ropeway.
b) A locomotive weighing 15 tonnef travels round a curve of 80 m radius at a speed of 30 kmph.
If the gauge is 1 meter what should be the super elevation of the outer rail over the inner rail so
that there is no thrust between the flanges of the outer wheel and the outer rail?
8. Write notes on:
a) Trolley wire locomotive
b) Gate end stage loader
OR
9. a) What is tractive effort and drawbar pull ?
b) A locomotive weighs 15 tonnef and the adhesion to the tracks is 2246 N per tonnef is moving
up in an adverse gradient of 1 in 5.The running resistance of the locomotive is 67 N per tonnef.
Calculate the coefficient of adhesion and drawbar pull which the locomotive is capable of
exerting.
********
MINE ENVIRONMENTAL ENGINEERING-I
MRCET- Department of Mining Engineering Model Question Paper-1
6. What is natural ventilation and the method of calculation of NVP from air density?
OR
7. a) On what factors the mine fan in selected and write about fan testing types?
b) Brief about control capacity of mine fans?
10. Calculate the quantity of air required as per statute if in a persons ventilation split employing
25 in a shift and 50 persons in a large shift, producing 450 tonnes of output daily.Draw a line
diagram of ventilation layout neatly?
OR
11. Write the procedure of conducting ventilation survey?
********
MRCET- Department of Mining Engineering Model Question Paper-2
OR
5. a) What are the laws of air flow?.
b) Compare the forcing fan with an exhaust fan?
6. What are principle types of mine fans and their principle of operation?
OR
7. Discuss about the operation of fans in series and parallel?
OR
11.a) Draw the layout of ventilation system of a metal mine
b) What is meant by splitting of air
********
MRCET- Department of Mining Engineering Model Question Paper-3
6. Write about the suitability, merits and limitations of mine fans? (10)
OR
7. Discuss about their efficieneies and characteristics? (10)
8. Discuss about ascentional and descentional ventilations and homotropal and antitropal
ventilation system with layouts? (10)
OR
9. Write about overlapping ventilation system air a long heading? (10)
10. Calculate
a) The motive column
b) The NVP (assuming barometric pressure in D.C shaft is 750 mm of h.g) if the mean air
temperature in DC shaft 400 M deep in 28ºC and uc shaft is 38ºC ? (5+5)
OR
11). A total quantity of 100 m³/min of air passing through two splits. One airway is 2.5 m×1.5 m
and 100 m long. And other, with similar lining is 2 m×1.5 m and 125 m long. Calculate the
quantity of air passing in each split? (10)
********
UNDERGROUND COAL MINING TECHNOLOGY
MRCET- Department of Mining Engineering Model Question Paper-1
8. What are the types of longwall method of working giving their advantages and disadvantages?
OR
9. Write on the mechanized longwall face organization?
10. What is hydraulic mining? Write in brief the operation of getting coal and types of transport
of coal?
OR
11. Write about the support system of longwall mechanized face.?
********
MRCET- Department of Mining Engineering Model Question Paper-2
4. What are the advantages and disadvantages of board and pillar method of mining?
OR
5. How to determine the size of panel by assuming your own conditions?
OR
7. Draw layouts of manual and mechanized development districts with organization?
10. Discuss the sequence of operations of shearer is a mechanized longwall face, Calculate the
amount of coal in coal seam
OR
11. Longwall panel having thickness of 1.2 m, with length of face 110 meters and web of the
shearer is 0.6m. cutting 2.5cuts(specific gravity of coal is 1.5)
********
MRCET- Department of Mining Engineering Model Question Paper-3
OR
3. Discuss about the reserves of coal seam and their classification.
4. What are the conditions suitable for the application of mechanized mining?
OR
5. Discuss about the deployment of manpower in a mechanized depillaring district by drawing
the layout of transport system?
6. Write about the safety organization adopted at mine area and company level?
OR
7. What are the statutory provisions to be observed for depillaring operations?
8. Discuss about the salient features for the success of longwall mining over board and pillar
methods?
OR
9. What are the plant and equipment used in longwall face with their specifications?
********