Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
AMPS Scanner
Rx level
RX level selected channel
RX level Nth best
RX level top N
Analysis
CDMA
CDMA Scanner
CDMA:Data
CDMA:Finger
CDMA:Power control
CDMA:RACH
CDMA:RLP statistics
Service ID
Number of resets
Received fill frames
Received blank frames
Received null frames
Received new data frames
Received fundamental data frames
Received bytes
Received RLP erasures
Received multiplexer erasures
Transmitted NAKs
Transmitted retransmitted frames
Number of NAK aborts
Transmitted idle frames
Transmitted new data frames
Transmitted fundamental data frames
Transmitted bytes
Last RTT
Number of 20-ms time frames for the last round-trip time measurement
Block of bytes used
Received NAKs
Total number of negative acknowledgement frames received.
Largest block of consecutive erasures
Number of retransmitted frames not found
Received retransmitted frames
Received idle frames
CDMA:SHO
CDMA:Service configuration
Service option
Forward traffic type
F-DCCH radio configuration
R-DCCH radio configuration
file:///C:/Program Files/Anite/Nemo Analyze/Documentation/AnalyzeKPI.html 10/89
10/10/2019 Nemo Analyze KPI List
Circuit-switched data
Requested CS bitrate
Indicates the requested data call resources. Recorded when data call is initiated or reconfigured.
Channel coding
Recorded when data call resources have changed.
CS data mode
Indicates the requested data call resources. Recorded when data call is initiated or reconfigured.
Modem type
Indicates the requested data call resources. Recorded when data call is initiated or reconfigured.
Number of UL timeslots
Recorded when data call resources have changed.
Number of CS data timeslots uplink.
Number of DL timeslots
Recorded when data call resources have changed.
Number of CS data timeslots downlink.
CS data timeslots uplink
CS data timeslots downlink
Data channel request UMTS
Indicates the requested data call resources. Recorded when data call is initiated or reconfigured.
Data channel request GSM
Indicates the requested data call resources. Recorded when data call is initiated or reconfigured.
RRLP signaling
Recorded when an RRLP signaling message is sent or received.
DVB-H
DVB type
Recorded when DVB-H channel configuration changes.
DVB-H service state
Recorded when DVB-H channel configuration changes.
DVB-H frequency
Recorded when DVB-H channel configuration changes.
DVB-H cell ID
Recorded when DVB-H channel configuration changes.
DVB-H transmission mode
DVB-H Scanner
Frequency
Carrier RSSI
DVB-H MER
Scanning configuration
Defines scanning settings.
EVDO
Random variable
Random variable represents the random variable that was used to calculate the new reverse rate (Rev 0 only).
Transition probability
Transition probability that was used to calculate the new reverse rate (Rev 0 only).
Condition RRI
Condition reverse rate provides the reverse rate that was calculated based on the above factors (Rev 0 only).
Actual RRI
Actual reverse rate. This should be less than condition RRI or there is not enough data to be sent (Rev 0 only).
Padding bytes
Number of padding bytes included in the reverse link packets (Rev 0 only).
Multiuser ACK ratio
Searcher state
Searcher window size
Searcher MSTR
Searcher status per pilot
Searcher status peak
Sector ID
128-bit sector address of the serving sector.
Sector subnet identifier
Hybrid mode
Reverse rate limit (Rev 0 only)
Recorded when parameters change.
Current rate (Rev 0 only)
Recorded when parameters change.
Combined busy bit (Rev 0 only)
Recorded when parameters change.
Reverse Activity Bit (RAB) is a control bit sent in regular intervals that indicates if the access network is busy or not.
Maximum PA headroom available (Rev 0 only)
Recorded when parameters change.
DRC cover
Cover used to transmit DRC.
DSC value
Data source control value transmitted by the mobile (Rev A only).
MAC index
DRC cover per pilot
RPC cell index
DRC lock
Slot FRAB
Slot fast reverse activity bit.
Slot QRAB
Slot quick reverse activity bit.
EVDO Scanner
EVDO:Connection
Connection attempt
Recorded when connection layer is connected.
Connection release
Recorded when connection layer is released.
ALMP state
Initialization protocol state
Idle protocol state
Connected protocol state
Route update protocol state
Overhead message protocol state
EVDO:FCH packets
CC38400 Good
Counter for 38.4 k control channel packets with good CRC
CC38400 Bad
Counter for 38.4 k control channel packets with bad CRC
TC307200Short Good
Counter for 302.2 (short) traffic channel packets with good CRC
TC307200Short Bad
Counter for 302.2 (short) traffic channel packets with bad CRC
TC307200Long Good
Counter for 307.2 (long) traffic channel packets with good CRC
TC307200Long Bad
Counter for 307.2 (long) traffic channel packets with bad CRC
TC614400Short Good
Counter for 614.4 k (short) traffic channel packets with good CRC
TC614400Short Bad
Counter for 614.4 k (short) traffic channel packets with bad CRC
TC614400Long Good
Counter for 614.4 k (long) traffic channel packets with good CRC
TC614400Long Bad
Counter for 614.4 k (long) packets decoded in 2 slots
TC921600 Good
Counter for 921.6 k traffic channel packets with good CRC
TC921600 Bad
Counter for 921.6 k traffic channel packets decoded with bad CRC
CC76800 Good
Counter for 76.8 k control channel packets with good CRC
TC1228800Short Good
Counter for 1228.8 k (short) traffic channel packets with good CRC
TC1228800Short Bad
Counter for 1228.8 k (short) traffic channel packets with bad
TC1228800Long Good
Counter for 1228.8 (long) traffic channel packets with good CRC
TC1228800Long Bad
Counter for 1228.8 (long) traffic channel packets with bad CRC
TC1843200 Good
Counter for 1843.2 k traffic channel packets with good CRC
TC1843200 Bad
Counter for 1843.2 k traffic channel packets with bad CRC
TC2457600 Good
Counter for 2457 k traffic channel packets with good CRC
TC2457600 Bad
Counter for 2457 k traffic channel packets with bad CRC
CC76800 Bad
Counter for 76.8 k control channel packets with bad CRC
TC38400 Good
Counter for 38.4 k traffic channel packets with good CRC
TC38400 Bad
Counter for 38.4 k traffic channel packets with bad CRC
TC76800 Good
EVDO:Finger
Ec/I0
If antenna configuration is 2, then this represents Ec/Io for the paired fingers.
Ec/I0 antenna 0
Ec/I0 for finger tracking RX0
Ec/I0 antenna 1
Ec/I0 for finger tracking RX1
Finger locked
Absolute finger offset
Note that the accuracy can be greater than one chip.
Pilot number
Finger index
Index of the demodulator finger
RPC cell index
Value/index assigned to a cell by AT.
ASP index
Value/index assigned to a sector by AT.
EVDO:Power control
Power limited/Channel
Power amplifier/Channel
Percentage of "UL power up" commands
TX power
TX power (rev B)
Closed loop adjustment value
Closed loop adjustment value (rev B)
TX pilot power
TX open loop power
TX power determined by the open loop adjust mechanism
TX pilot power (rev B)
DRC channel to pilot ratio
ACK channel to pilot ratio
Data channel to pilot ratio
PA max
Maximum recommended headroom available (Rev A). The mobile station indicates the available Power Amplifier (PA)
headroom to the access network. The access network can assign carriers based on the mobile stations available power
amplifier headroom.
EVDO:RACH
EVDO:RLP statistics
Service ID
Identifies RLP service.
Received NAKs
Retransmitted bytes
Transmitted new data bytes
Transmitted bytes
NAK timeouts
Contains NAK timeouts and aborts.
Reset count
Total resets that have occurred, initiated either by the AN or the AT.
Resets requested by the AT
Reset ACKs received from the AN
Resets requested by the AN
Received NAKs in bytes
Number of retransmitted frames not found
Received duplice bytes
Received retransmitted bytes
Received new data bytes
Received bytes
Transmitted NAKs
Transmitted NAKs in bytes
Received frames
Received new frames
Received retransmitted frames
Received frames with first data unit
Received frames with last data unit
Transmitted frames
Transmitted new frames
Retransmitted frames
Transmitted frames with first data unit
Transmitted frames with last data unit
Link flow ID
Route number
Flow protocol
Route protocol
Packet stream
Whether link flow is packet-based.
file:///C:/Program Files/Anite/Nemo Analyze/Documentation/AnalyzeKPI.html 19/89
10/10/2019 Nemo Analyze KPI List
Sequence type
Whether link flow is doing segment-based sequencing.
Multilink multi-flow RLP forward link statistics
Multilink multi-flow RLP forward link QN instance statistics
Multilink multi-flow RLP reverse link statistics
Multilink multi-flow RLP RX processing statistics
EVDO:Session
Session attempt
Session state
Summary session layer states
GAN
GAN signaling
Packet technology
Packet technology during data transfer
Packet technology between nemo events DAA to DAD or DAF
Packet state
Routing area code
LLC throughput uplink
The value of this parameter is calculated based on the SDUs that are stransferred through the LLC layer. Missing and
erroneous LLC blocks are excluded from the throughput calculation.
LLC throughput downlink
The value of this parameter is calculated based on the SDUs that are successfully transferred through the LLC layer.
Missing and erroneous LLC blocks are excluded from the throughput calculation.
LLC retransmission rate uplink
Cell reselection
Handover events
Handover attempt
Handover success
Handover failure
WLAN throughput uplink
WLAN throughput downlink
GSM
C1 criterion
Path loss criterion parameter C1 is used for cell selection and reselection. See 3GPP TS 145.008 subclause 6.4 (with GPRS,
also subclause 10.1.2).
C2 criterion
The reselection criterion C2 is used for cell reselection. This parameter is used for cell reselection when the value of the
path loss criterion C1 is over zero. See 3GPP TS 145.008 subclause 6.4.
Neighbor list
List of GSM and UMTS neighbors seen by the terminal
Number of missing GSM neighbors
C31 criterion
The signal level threshold criterion parameter C31 is used to determine whether prioritized hierarchical GPRS and LSA cell
re-selection shall apply. See 3GPP TS 145.008 subclause 10.1.2.
C32 criterion
The cell ranking criterion C32 is used in selecting cells from cells that have the same priority. See 3GPP TS 145.008
subclause 10.1.2.
HCS priority class
Defines the cell re-selection order of the cells. See 3GPP TS 145.008 subclause 10.1.3.
HCS threshold
See 3GPP TS 145.008 subclause 10.1.2.
RX quality full
Quality value measured on every TDMA frame. Use this value when DTX is inactive. See 3GPP TS 145.008 subclause 8.4.
RX quality sub
Quality value measured over the subset of every TDMA frame. Use this value when DTX is active. See 3GPP TS 145.008
subclause 8.4.
Frame error rate full
This calculation assumes all 25 frames of the SACCH multiframe have been sent. Just like RXQual Full, when DL DTX is on,
FER FULL will become invalid. This is because only 2 or 3 frames are sent when DL DTX is on.
Frame error rate sub
FER Sub is calculated as the ratio of erroneous frames to number of sent frames. With EFR speech, only 2 out of the 25
are sent when DL DTX is on. With AMR speech, either 2 or 3 frames will be sent.
Frame error rate TCH
This calculation concentrates only on TCH frames. It is also more robust when DL DTX is changing. This is because it
concentrates on the ratio of TCH frame errors to TCH frames sent.
DTX downlink
Defines if the DTX is used during the previous reporting period.
MS power level (dBm)
Recorded when parameter sample is received from the device and the received sample differs from the previous result.
MS power level
Recorded when parameter sample is received from the device and the received sample differs from the previous result.
Radiolink timeout
Recorded when the radio link timeout changes.
The counter used in determining when the radio link failure condition is declared. The value of the counter is decreased by
one when SACCH message decoding fails. When decoding succeeds, it is increased by two. If the value of the counter
drops to zero, the radio link failure condition is declared. See 3GPP TS 145.008 subclause 5.
Timing advance
Recorded when timing advance changes.
Reported timing advance.
C/I average
C/I average is calculated over the reporting period. The C/I average is the average of all C/I values per hopping channel
(and timeslot with GPRS) when this information is available. If C/I per hopping channel or per timeslot is not available, the
C/I average calculation method is vendor specific.
C/I per timeslot
Separate C/I result for each dedicated GRPS timeslot. C/I calculation method is vendor specific.
C/I per hopping channel
C/I per hopping channel worst
Channel number and C/I of the hopping channel with worst C/I
RSSI per hopping channel
Distance based RX level average from scanner for serving cell
RX level Nth best
Nth best Rx level among serving and neighbouring cells.
RX level Nth best (dBuV/m)
Nth best Rx level among serving and neighbouring cells.
RX level Nth best neighbor
GSM Scanner
Scanning configuration
Defines scanning settings.
C/A
Ratio between channel and adjacent channels (dB)
C/A selected NCC
Ratio between channel and adjacent channels (dB)
Cellscan
Recorded when parameter sample is received from the device. With GSM the system information messages, and with
UMTS and LTE the system information blocks, are decoded to produce the information required for this measurement
event.
Interference analysis
GSM:GPRS/EDGE
Packet RX quality
Recorded when parameter sample is received from the device and the received sample differs from the previous result.
See 3GPP TS 145.008 subclause 8.2.3.1. This parameter is only recorded for GPRS.
C value
Recorded when parameter sample is received from the device and the received sample differs from the previous result.
Received signal level of each paging block monitored by the MS according to its current DRX mode and its paging group.
See 3GPP TS 145.008 subclause 10.2.3.1. This parameter is only recorded for GPRS.
Signal variance
Recorded when parameter sample is received from the device and the received sample differs from the previous result.
Average variance of signal level (C value). See 3GPP TS 145.008 subclause 10.2.3.1. This parameter is only recorded for
GPRS.
Timeslot interference
Recorded when parameter sample is received from the device and the received sample differs from the previous result.
Timeslot interference level relative to C value. See 3GPP TS 145.008 subclause 10.3. This parameter is only recorded for
GPRS.
Downlink signaling counter current
Recorded when downlink signaling counter value changes.
The counter used in determining when the downlink signaling failure condition is declared. Whenever the message is
decoded in the paging subchannel; if the message decoding is successful, the DSC counter is increased by one; if the
message decoding fails, the DSC counter is decreased by four. The downlink signaling failure condition is declared if the
DSC counter drops to zero or below. See 3GPP TS 145.008 subclause 6.5.
Downlink signaling counter maximum
Recorded when downlink signaling counter value changes.
The maximum value of the DSC counter.
BEP mean class GMSK
Recorded when parameter sample is received from the device and the received sample differs from the previous result.
Recorded only when EGPRS is used.
See 3GPP TS 145.008 subclause 8.2.3.2.
BEP CV class GMSK
Recorded when parameter sample is received from the device and the received sample differs from the previous result.
Recorded only when EGPRS is used.
See 3GPP TS 145.008 subclause 8.2.3.2.
BEP mean class 8-PSK
Recorded when parameter sample is received from the device and the received sample differs from the previous result.
Recorded only when EGPRS is used.
See 3GPP TS 145.008 subclause 8.2.3.2.
BEP CV class 8-PSK
Recorded when parameter sample is received from the device and the received sample differs from the previous result.
Recorded only when EGPRS is used.
See 3GPP TS 145.008 subclause 8.2.3.2.
RLC/MAC and L3 signaling
RLC/MAC/L3/RRC signaling DL and UL separated
RLC/MAC/L3/RRC signaling
RLC/MAC message search
Searches for user-defined messages, with user-defined string in the message name
RLC/MAC signaling
LLC signaling
Recorded when an LLC signaling message is sent or received.
Packet technology
Packet technology during data transfer
TFI uplink
RLC window size uplink
TFI downlink
RLC window size downlink
RLC/MAC signaling parameter search
Searches for user-defined text inside decoded messages, and returns the following field for the first match. With the
search start text it is possible to configure, that search starts after first occurence of another text in the decoded message
EDGE coding DL distribution
EDGE coding UL distribution
GPRS coding DL distribution
GPRS coding UL distribution
Uplink TBF establishment cause
Recorded after TBF uplink establishment attempt. The recorded information is based on RLC/MAC and layer3 signaling
messages.
TBF UL establishment status
Recorded after TBF uplink establishment attempt. The recorded information is based on RLC/MAC and layer3 signaling
messages.
LTE
LTE Scanner
P-SCH CINR
The ratio between synchronization channel received power and interference and noise from the same synchronization
signal set.
LTE RRC signaling
RSRP Nth best distance based average selected carriers
RSRP distance based average selected carriers
Carrier RSSI (frequency scanning mode) selected channel
Carrier RSSI (frequency scanning mode)
Carrier RSSI (OFDM scanning mode) selected channel
Carrier RSSI (OFDM scanning mode)
RS CINR Nth strongest cell selected carriers
RS CINR top N cell selected carriers with BTS ref. info
RS CINR top N cell selected carriers
RS Carrier RSSI Nth strongest cell selected carriers
RSRQ Nth best selected carriers with BTS ref. info
RSRQ Nth best selected carriers
RSRQ distance based average selected carriers
RSRQ top N selected carriers with BTS ref. info
RSRQ top N selected carriers
RSRP Nth best selected carriers with BTS ref. info
RSRP Nth best selected carriers
RSRP Nth best selected carriers MNC
RSRP MNC
RSRP Nth best selected carriers (dBuV/m)
RSRP top N selected carriers with BTS ref. info
RSRP top N selected carriers
L3 signaling
LTE RRC signaling parameter search
Searches for user-defined text inside decoded messages, and returns the following field for the first match. With the
search start text it is possible to configure, that search starts after first occurence of another text in the decoded message
Scanning configuration
Defines scanning settings.
F-factor scanner (CINR estimate)
Estimate of SNR/CINR assuming all cells are fully loaded. Calculation: best cell RSCP / (2nd best RSRP + 3rd best RSRP +
... + Thermal noise (-132dBm)). Expressed in decibels
F-factor scanner
F-factor indicates the interference conditions assuming all cells are fully loaded (worst case scenario). Calculation: (2nd
best RSRP + 3rd best RSRP + ... + Thermal noise (-132dBm))/best cell RSCP.
Number of pilots within X dB window from the best
Number of cells where the RSRP is within user-definable window from the best cell
Cellscan
Recorded when parameter sample is received from the device. With GSM the system information messages, and with
UMTS and LTE the system information blocks, are decoded to produce the information required for this measurement
event.
Cyclic prefix DL
Detected TX antenna ports
RSRP selected PCI scanner
RS Carrier RSSI selected PCI scanner
Scanning result indication
The parameter contains the status of the measurement result. This is a bit field so the value of the parameter is the sum
of all simultaneouns measurement statuses, e.g. if the antenna power imbalance and frequency offset too large conditions
happen simultaneously the recorded value would be three.
2x2 MIMO rank estimation/PRB (Rohde & Schwarz)
2x2 MIMO rank estimation/PRB (Nemo FSR1)
2x2 MIMO condition number/PRB (Rohde & Schwarz)
2x2 MIMO condition number/PRB (Nemo FSR1)
2x4 MIMO rank estimation/PRB (Rohde & Schwarz)
2x4 MIMO rank estimation/PRB (Nemo FSR1)
2x4 MIMO condition number/PRB (Rohde & Schwarz)
2x4 MIMO condition number/PRB (Nemo FSR1)
RSRP/PRB
CINR/PRB
2x2 MIMO condition number (PCTel)
Physical resource block scanning results (PCTel)
Physical resource block OLSM CQI (PCTel)
RS scanning results per antenna port
RSRP, RSRQ, and CINR reported per cell per antenna port
RSRP selected antenna port
RSRPs readings of selected antenna port
RS Carrier RSSI selected antenna port
RSSI readings of selected antenna port
RSRQ selected antenna port
RSRQ readings of selected antenna port
RS CINR selected antenna port
RSRQ readings of selected antenna port
RSRP
Reference signal received power is the linear average of the power contributions of the resource elements that carry cell-
specific reference signals within the considered measurement frequency. 3GPP TS 36.214 subclause 5.1.1.
RS CINR Nth strongest cell
CINR of the Nth strongest cell in terms of RSRP
RSRQ Nth strongest cell
RSRQ of the Nth strongest cell in terms of RSRP
S-SCH received CINR Nth strongest cell
S-SCH received CINR of the Nth strongest cell
P-SCH received quality Nth strongest cell
P-SCH received quality of the Nth strongest cell
S-SCH received quality Nth strongest cell
S-SCH received quality of the Nth strongest cell
S-SCH received power Nth strongest cell
S-SCH received power of the Nth strongest cell
P-SCH received power Nth strongest cell
P-SCH received power of the Nth strongest cell
RSRP Nth strongest cell
RSRP of the Nth strongest cell
Physical cell ID Nth strongest cell
PCI of the Nth strongest cell in terms of RSRP
RS Carrier RSSI Nth strongest cell
RSSI of the Nth strongest cell in terms of RSRP
RSRQ selected PCI scanner
RSRQ
Reference signal received quality is the ratio N * RSRP / E-UTRA carrier RSSI, where N is the number of resource blocks of
the E-UTRA carrier RSSI measurement bandwidth. The measurements in the numerator and denominator are made over
the same set of resource blocks. 3GPP TS 36.214 subclause 5.1.3.
LTE:Link adaptation
Requested throughput
Requested rank distribution
Requested rank (mode)
The most common requested rank over the reporting period
Wideband CQI for codeword 0
This is the average wideband CQI calculated over the reporting period. See 3GPP TS 36.213 subclause 7.2.
Wideband CQI for codeword 1
This is the average wideband CQI calculated over the reporting period. See 3GPP TS 36.213 subclause 7.2.
Subband CQI for codeword 0
The subband CQI is the average calculated over the subbands defined by higher layer or selected by mobile. This reported
subband CQI value is furthermore averaged over the reporting period before it is logged to the measurement event. More
information about CQI see 3GPP TS 36.213 subclause 7.2.
Subband CQI for codeword 1
The subband CQI is the average calculated over the subbands defined by higher layer or selected by mobile. This reported
subband CQI value is furthermore averaged over the reporting period before it is logged to the measurement event. More
information about CQI see 3GPP TS 36.213 subclause 7.2.
Wideband PMI
The logged value is the most commonly used value during the reporting period. A user equipment uses Precoding Matrix
Indicator (PMI) to inform the eNodeB which precoding matrix should be used for downlink transmission according to the
rank indication. See 3GPP TS 136.213 subclause 7.2.4.
CQI for codeword 0 per subband
The average channel quality index value over the reporting period for defined subband. Not available when the best M
select mode is used. More information about CQI see 3GPP TS 36.213 subclause 7.2.
CQI for codeword 1 per subband
The average channel quality index value over the reporting period for defined subband. Not available when the best M
select mode is used. More information about CQI see 3GPP TS 36.213 subclause 7.2.
PRB utilization DL delta primary vs. secondary carrier
Difference between DL PRB utilization percentage of primary and secondary carriers in LTE carrier aggregation (%)
PRB utilization DL
Downlink PRB utilization proportional to bandwidth and reporting period.
LTE:MAC
LTE:RACH
LTE:RRC
RxLevAccess
Band
Result
Number
ChannelType
Criteria
CurrentCCH
CurrentThreshold
CurrentPreferentialCriteria
CCH
PreferentialCriteria
Threshold
BN
DownLinkScrambling
UpLinkScrambling
Nortel
file:///C:/Program Files/Anite/Nemo Analyze/Documentation/AnalyzeKPI.html 39/89
10/10/2019 Nemo Analyze KPI List
RRC signaling
Other
All events
Event IDs of all occured Nemo file format Events
Selected events
Selected event IDs of all occured Nemo file format events
Measurement duration
All BTS reference cells
BTS custom parameter
This query returns custom column from the BTS file for the currently serving cell as specified by the user. Ht
Service off
Recorded when service state or mobility information changes.
Service on
Recorded when service state or mobility information changes.
Service info status
Recorded when service state or mobility information changes.
Date
Geographical bin area
Measurement file info
Measurement time
Modem message
Recorded when modem message is sent to or received from the device. At the moment this message is only logged when
Send Modem Message functionality is used from Nemo Outdoor.
Textual note
Recorded when textual note is recorded by the user.
Voice note
Marker
Recorded when the user adds a marker to the measurement.
Error text
Lock radio off
Lock channel
Lock sector
Lock system
Lock band
Lock cell barring
LTE lock sector
Invex backplane health information
Invex UIC health information
Invex HIM health information
Other:GPS
Velocity
Height
Distance
GPS fix quality
Number of satellites
Latitude and longitude
Latitude and longitude binned (MGRS)
Returns coordinates binned to squares of 1, 10, 100,1000, 10 000, or 100 000 meter side length, binned accorgin to
MGRS grid system.
Packet-switched data
Packet-switched data:Attach
Attach session
Information per attach session, time range between Nemo events GAA and GAD/GAF. Can be used as input in KPI
workbench to group other data per attach session
Attach attempt
Attach attempt success
Attach attempt failure
Detach
Attach setup time
Detach distribution
PS status
Packet-switched data:QoS
Services
Problem events
The query returns all problem events in Nemo fileformat. Results can be displayed in grid, colorcoded map, and print value
on the map.
Services:CEM Observer
Services:Data transfer
Services:Data transfer:Jitter
Services:Data transfer:PPP
Services:Data transfer:Throughput
Services:Dropbox
Services:FTP
Services:Facebook
Services:HTTP
HTTP attempt
HTTP success
HTTP failure
HTTP content
Recorded after data transfer has been completed and WAP/HTML content has been parsed.
Services:HTTP browsing
Services:IMAP
Services:Instagram
Services:Iperf
Services:Kodiak IPA
Services:LinkedIn
Services:MMS
MMS filename
For send MMS message type this is a name of the MMS message file. For retrieved and notification MMS types this a MMS
message reference (that is in a practice a content location in a URI form).
MMS send failure
MMS receive failure
MMS receive success
MMS send success
MMS send attempt
MMS notification received
MMS delivery report received
MMS receive attempt
MMS retrieval time
Definition according to ETSI TS 102 250-2: MMS retrieval time (MT) [s]. The time elapsing between the WAP get request
and the completion of the download of the MMS is be described by this parameter. Computation: MMS retrieval time (MT)
[s] = t2 - t1. t1: time when WAP get request is initiated by the terminal. t2: MMS is completely received, The m-
notifyResp.Ind is sent by the terminal (MT). Only those MMS are counted where the MMS receive attempt is included in
the measurement data.
MMS send time
Time elapsing from pushing the send button after the editing of a MMS-message to the completion of the data transfer is
described by this parameter. Computation: MMS send time (MO) [s] = t2 - t1. t1: send button is pushed (PDP context
activation is initiated by the terminal, followed by connection to WAP gateway. t2: MMS is completely sent to the MMSC,
Services:POP3
Services:Packet session
Session state
Summary session layer states
ALMP state
Initialization protocol state
Idle protocol state
Connected protocol state
Route update protocol state
Overhead message protocol state
Services:Ping
Services:PoC
Services:SFTP
Services:SMS
Services:SMTP
Services:Streaming\YouTube
Services:Trace route
Traceroute attempt
Recorded when data transfer is requested to or from the server. Begins the data transfer state.
Trace route
One measurement event is recorded for each trace route host.
Services:Twitter
Services:USSD
Services:VoIP
Services:Voice/video call
Services:Voice/video call:CSFB
Services:Voice/video call:Video
file:///C:/Program Files/Anite/Nemo Analyze/Documentation/AnalyzeKPI.html 55/89
10/10/2019 Nemo Analyze KPI List
Video protocol
Video call quality index
Video FER
Number of erroneous frames received.
Video frame rate uplink
Video frame rate downlink
Video rate downlink
Video rate uplink
Services:Voice/video call:VoLTE:AMR
Services:Voice/video call:Voice:AMR
Services:WAP
WAP attempt
WAP success
WAP failure
WAP content
Recorded after data transfer has been completed and WAP/HTML content has been parsed.
Spectrum scanner
Resolution bandwidth
To be able to scan large bandwidth spectrums, the total sweep bandwidth must be divided into smaller parts. The
resolution bandwidth defines the size of the smaller parts, each of which is scanned separately.
Sweep bandwidth
The total scanned bandwidth that is divided into smaller parts before the scanning.
Sweep minimum RX level
Minimum RX levels measured over bandwidth of 'resolution bandwidth'.
Sweep maximum RX level
Maximum RX levels measured over bandwidth of 'resolution bandwidth'.
Sweep center frequency
Sweep average RX level selected frequency
Sweep average RX level
The linear average of RX levels measured over bandwidth of 'resolution bandwidth'.
Spectrum scan
Scanning configuration
Defines scanning settings.
TD-SCDMA
Signal-to-interference ratio
See 3GPP TS 125.215 subclause 5.2.2.
TX power
Channel number
TD-SCDMA pilot pollution
Number of cells that are within user defined window from the best cell in terms of RSCP, when best RSCP is above user
defined threshold.
Treselection
The time which the new cell has had to be ranked better than the old cell before cell reselection is possible. See 3GPP TS
25.304 subclause 5.2.6.1.4.
Measurement event
Recorded when a UMTS measurement event is transmitted to the network based on signaling messages.
Cell reselection
Handover events
Handover attempt
Handover success
Handover failure
Timing advance
Timeslot ISCP
Timeslot RSCP
Cell parameters ID
Max TX power
DPCH channel number
RSCP serving cell
RSCP neighbour cells
Pathloss serving cell
Pathloss neighbour cells
Carrier RSSI
RLC throughput uplink per radio bearer
Uplink RLC throughput for specified radio bearer.
RLC throughput downlink per radio bearer
Downlink RLC throughput for specified radio bearer.
RLC retransmission rate uplink per radio bearer
TD-SCDMA Scanner
TD-SCDMA:HSDPA
TD-SCDMA:HSDPA:Link adaptation
TD-SCDMA:RACH
TD-SCDMA:RRC
TDMA
PSID4
PSID (private system identification) value 4.
REG PERIOD
If not available, set to -1.
RNUM
If LAREG parameter has the value of 1, RNUM parameter will have a value.
LAREG
PSID3
PSID (private system identification) value 3.
Digital color code
L3 signaling parameter search
Searches for user-defined text inside decoded messages, and returns the following field for the first match. With the
search start text it is possible to configure, that search starts after first occurence of another text in the decoded message
Downlink Band
Handover events
Handover attempt
Handover success
Handover failure
TDMA Scanner
Rx level
RX level selected channel
RX level Nth best
RX level top N
TETRA
Call type
Serving system
Recorded when channel configuration information changes.
Serving band
Recorded when channel configuration information changes.
Band
Channel number
Subchannel
Extended subchannel
Slot number
BER
Recorded when parameter sample is received from the device and the received sample differs from the previous result.
Bit error rate that is calculated with training sequence algorithm.
Message error rate
Recorded when parameter sample is received from the device and the received sample differs from the previous result.
TX power
MS transit power.
TX power change
TX power control algorithm
RSSI best
RSSI selected channel
RSSI serving cell
RSSI neighbor cells
RSSI Nth best neighbor
Push-to-talk communication type
Recorded when the push-to-talk state changes.
Push-to-talk state
L3 signaling
Recorded when a Layer 3 or an NAS signaling message is sent or received.
L3 message search
Searches for user-defined messages, with user-defined string in the message name
LLC signaling
Recorded when an LLC signaling message is sent or received.
L3 signaling parameter search
Searches for user-defined text inside decoded messages, and returns the following field for the first match. With the
search start text it is possible to configure, that search starts after first occurence of another text in the decoded message
CS status
TETRA:Encryption
Encryption
Air interface encryption
Recorded when ciphering information is modified.
Ciphering KSG
Recorded when ciphering information is modified.
Ciphering SCK
Recorded when ciphering information is modified.
TETRA:Mobility management
LAC
Location area update failure
Recorded based on MM layer3 signaling when location area update has failed. This measurement event terminates the
location area update state.
Location area update attempt
Recorded when the mobile starts location area update using MM layer3 signaling message. This measurement event
begins the location area update state.
Location area update success
Recorded based on MM layer3 signaling when location area update has been successful. This measurement event
terminates the location area update state.
Location area update time
Cell reselection
Handover events
Handover attempt
Handover success
Handover failure
BestServerRxLev
BestServerChannel
BestServerFrequency
2ndBestServerRxLev
2ndBestServerChannel
2ndBestServerFrequency
ExtendBestServerRxLev
ExtendBestServerChannel
ExtendBestServerFrequency
Speech Rx Duration
Speech Tx Duration
PTT Duration
ST Transmitted Power
CCH Selection
RB Selection
Nominal Frame Error Rate
MeanRxLevCCHx
MeanRxLevCCHx with BTS ref. information
RxLev_CCH39k
CurrentMeanRxLev
EstimatedTxPower
NborMeanRxLev_X
BestNborCellRxLev
BestNborCellCCH
2ndBestNborCellRxLev
2ndBestNborCellCCH
FrameErrorRate Level
ChannelMonitoring
TrafficChannel
InvalidFrames_Number
Terminal_Mode
TemperatureAlarm
InvalidMessage
Text_Message
CommSuspended
CommReestablishment
CommServiceDenied
CommReady
STAlarm
CommEnter
CommLeave
PTTRequest
PTTRelease
CSelStart
CSelDistribTKGList
CSelDistribEmergencyList
CSelDistribMOCHList
DMNMActivation
DMNMDetection
LostChannel
RSelGMSKDetection_NOK
RSelBestNeighbourCell
CSelRegistration_OK
CSelRegistration_NOK
Fast_Registration
Tunnel_Out
Tunnel_In
EventNewTRState
Cell_Memorization
Tetrapol:Independent:GPS Data
Distance
Latitude and longitude
NbSat
Speed
Source
Level
Code
Label
HardwareType
SecondaryHardwareType
LinkType
ProjectType
SoftwareVersion
MaxNominalTxPower
SerialPort
UseInterfaceBox
ProjectName
ChannelSpacing
DuplexSpacing
InitChannel
XVCO
ChannelOffset
SerialBaudRate
Power
STMode
State
AvRLinkQual BERCl1
AvRLinkQual BERCl2
AvRLinkQual BER
AvRLinkQual FER
TotalNbFrames
RLinkQual BERCl1
RLinkQual BERCl2
RLinkQual BER
RLinkQual FER
TotalNbFrames
Channel
RxLev
InterfaceVersion
STAddress
SerialNumber
SoftwareService
NominalOG
ResetOrigin
Trap1
Trap2
Alarm
DebugFlag
DebugClass
ForwardState
HostAddress
STRange
STType
LoudSpeakerState
SpeechVolume
ToneVolume
PTTPriority
CallType
CipheringKeyIndex
CommType
AcceptIncomingCall
AutoEntryInFallBackMOCH
AutoEntryInBroadcastCall
LocalManualKey
PTTInBroadcastCall
OutgoingExternGroupCall
AutoIncomingCallAnswer
PriorityScanMode
DMNM
DataImplicitAddressing
MOCH
Emergency
COV
EmergencyNotification
CrisisNotification
BroadcastNotification
CallCompositionNotification
OverloadNotification
CellActivationInd
StatusInd
CrisisId
EmergencyId
CipheringType
OverCipheringKeyIndex
Priority
MOCHId
file:///C:/Program Files/Anite/Nemo Analyze/Documentation/AnalyzeKPI.html 70/89
10/10/2019 Nemo Analyze KPI List
CellForcingType
AccessType
Activated
Value
Reference
AlarmType
SignalStrength_BarLevel
EndCause
Available
Merged
TKGId
CallerId
RecordedFilename
ReferenceFilename
ListeningQual
EffortQual
ParameterType
CauseType
CauseParamWriteFailure
CCRConfig
CCRParam
BNNb
ChannelId
SynchroCCH
SystemInfoMode
BCH
ROAM
ECCH
ATTA
MuxType
Sim
CountryCode
Network
Version
SystemIdMode
LocId
Scrambling
TxMax
RadioTimeOut
PwrAdjust
SystemTime
MinRegClass
MinServClass
CellRadioType
Revision
DC
CSO
CSG
CellDistribMode
Index
COVId
CallPriority
GroupId
MOCHType
AdditionalParticipants
NeighbourCellId
OGType
OG
CurrentCellId
SelRegType
SelType
Restriction
BNId
RSW
BS
PreferentialBN
CSelStart Cause
CSelStart Type
CSelRegistration Result
TKGType
OGId
Cause
AppId
ContextReference
BNType
Loc
Exp
SelectionCriteria
MeansType
C1
C2
TxPower Level
Tetrapol:Queries
Nominal FER
RxLev selected channel
RxLev min
RxLev max
RxLev average
Tetrapol:Statistics data
RSelDuration
FastRSelDuration
CSelDuration
UMTS
UMTS Scanner
Delay CPICH
Delay P-SCH
Delay S-SCH
Delay profile CPICH
Delay spread CPICH
Timeslot scan P-SCH
Wideband RSSI
Wideband RSSI selected carrier
RSCP CPICH
RSCP CPICH distance based average selected carriers
RSCP CPICH Nth best distance based average selected carriers
RSCP CPICH selected carrier
RSCP CPICH selected cell ID (BTS ref.)
RSCP CPICH selected scrambling code
RSCP CPICH best
RSCP CPICH Nth best
RSCP P-SCH
RSCP S-SCH
RSCP CPICH (Tx diversity)
RSCP PPCH
Ec/N0 CPICH
Ec/N0 CPICH selected carrier
Ec/N0 CPICH selected cell ID (BTS ref.)
Ec/N0 CPICH selected scrambling code
Scrambling code best
Ec/N0 CPICH best
Ec/N0 CPICH Nth best
Ec/N0 CPICH distance based average selected carriers
Ec/N0 CPICH Nth best with BTS ref. information
Ec/N0 CPICH selected carrier with BTS ref. information
Measured CPICH list selected carrier (BTS ref.)
Ec/N0 P-SCH
Ec/N0 S-SCH
Ec/N0 CPICH (Tx diversity)
Ec/N0 PPCH
SIR CPICH
SIR CPICH selected scrambling code
SIR CPICH best
RSCP CPICH top N selected carriers
RSCP CPICH Nth best selected carriers
RSCP CPICH Nth best selected carriers MNC
RSCP CPICH MNC
RSCP CPICH Nth best selected carriers (dBuV/m)
UMTS:HSDPA
Packet technology
Packet technology during data transfer
Packet technology between nemo events DAA to DAD or DAF
Avg. MAC-HS throughput per scrambling code
HS-SCCH usage
Recorded every 200 milliseconds to indicate HS-SCCH channel usage based on the trace messages of the mobile. This
measurement event is recorded simultaneously with the PLAID measurement event.
Defines the ratio of TTIs when new or retransmitted data is indicated using this HS-SCCH channelisation code. Note that
the sum of the percentages is 200 when the measurement event contains information about primary and secondary
HSDPA cells.
HS-SCCH usage combined
HS-SCCH usage combined is parameter where all channels usage percentages are summed together
HARQ Throughput
Recorded every 200 milliseconds to indicate HSDPA HARQ throughput based on the trace messages of the mobile. This
measurement event is recorded simultaneously with the PLAID measurement event.
The value of the parameter is calculated from the transport block sizes for each HARQ process separately.
HARQ BLER
Recorded every 200 milliseconds to indicate HSDPA HARQ throughput based on the trace messages of the mobile. This
measurement event is recorded simultaneously with the PLAID measurement event.
The ratio of erroneously received MAC-hs PDUs to all received MAC-hs PDUs for each HARQ process separately.
HSDPA physical layer requested throughput
Computational throughput based on the transport block sizes indicated by the CQI values. In MIMO mode, only CQI type A
is used for the calculation. This is the throughput that would have been achieved if the network had sent the link
adaptation parameters defined by the CQI.
Number of active HS-SCCHs
Number of HS-SCCHs that have being active (hs-scch usage > 0) during the reporting interval
G-factor estimate
Calculation: Best serving cell RSCP/(2nd best RSCP + 3rd best RSCP + ... + Thermal noise (-101dBm)) estimates the G-
factor with the assumption that all cells are equally loaded
HSDPA MIMO
MIMO Ec/N0
Currently the recording interval is about two times per second. This measurement event is currently only logged for
serving cells.
MIMO RSCP
Currently the recording interval is about two times per second. This measurement event is currently only logged for
serving cells.
MIMO RSSI
Currently the recording interval is about two times per second. This measurement event is currently only logged for
serving cells.
UMTS:HSDPA:Link adaptation
UMTS:HSUPA
UMTS:HSUPA:Link adaptation
UMTS:HSUPA:Scheduling info
UMTS:RACH
UL interference
Recorded after random access to the network has been attempted. With UMTS FDD, a RACHI measurement event is
recorded for each random access procedure.
UMTS:RRC
RRC state
RRC state during data transfer
RRC state filtered from the tim instants where data transfer is active (between DREQ and DCOMP nemo events
RRC and L3 signaling
RLC/MAC/L3/RRC signaling DL and UL separated
RLC/MAC/L3/RRC signaling
RRC message search
Searches for user-defined messages, with user-defined string in the message name
RRC signaling parameter search
Searches for user-defined text inside decoded messages, and returns the following field for the first match. With the
search start text it is possible to configure, that search starts after first occurence of another text in the decoded message
RRC signaling
RRC connection attempt
Recorded based on RRC signaling when RRC connection is attempted. This measurement event begins the RRC connection
attempt state.
RRC connection connected
Recorded based on RRC signaling when RRC connection is established. This measurement event begins the RRC
connection state.
RRC connection disconnected
RRC connection attempt failure
Recorded based on RRC signaling when RRC connection attempt fails. This measurement event terminates the RRC
connection attempt state.
Dropped RRC connection
Recorded based on RRC signaling when RRC connection is released. This measurement event terminates the RRC
connection state.
WLAN
WiMAX
Handover failure
MAC signaling
WiMAX frame ratio downlink
WiMAX frame ratio uplink
WiMAX coding type used on DL-MAP
WiMAX repetition coding used on DL-MAP
WiMAX base station ID
Six colon separated hex values.
WiMAX MAC state
WiMAX frequency
WiMAX FFT size
WiMAX bandwidth
WiMAX RSSI
Signal strength.
WiMAX RSSI deviation
WiMAX CINR
Channel to interference-noise ratio.
WiMAX CINR deviation
Channel to interference-noise ratio devitaion.
WiMAX neighbor RSSI
WiMAX neighbor RSSI deviation
WiMAX neighbor CINR
WiMAX neighbor CINR deviation
WiMAX TX power
MS transmit power.
WiMAX TX reference power
WiMAX TX power headroom
WiMAX PER
Recorded when parameter sample is received from the device and the received sample differs from the previous result.
This UMTS measurement event is recorded simultaneously with the PLAID measurement event and only during HSDPA
session.
WiMAX frame lost ratio
Recorded when frame error rate reports are received from the device.
WiMAX TX power BS offset
WiMAX initial ranging max TX power
WiMAX BS EIRP
Base station effective isotrophic radiated power.
WiMAX BS noise + interference level
WiMAX MAC throughput uplink
WiMAX MAC throughput downlink
WiMAX MAC packet rate uplink
WiMAX MAC packet rate downlink
WiMAX preamble index
WiMAX IDCell
WiMAX segment
WiMAX Scanner
WiMAX:Link adaptation
hidden
iDEN
Domain status
Recorded when service state or mobility information changes.
Channel number
Color code
Frequency
Cell identifier
Adaptation rate
Cutback level
Monitor all flag
Monitor paging subchannel
Interconnect paging subchannel
Packet data paging subchannel
Dispatch paging subchannel
Interleave
Offset
Subslot
Extended color code
RX level
RX level neighbor
SQE
Carrier SQE neighbor
Sync count
Sync count neighbor
Serving system and band
Recorded when channel configuration information changes.
Serving system
Recorded when channel configuration information changes.
Serving band
Recorded when channel configuration information changes.
Push-to-talk state (iDEN)
Recorded when voice call configuration or state changes.
L3 signaling
Recorded when a Layer 3 or an NAS signaling message is sent or received.
Cell reselection
Handover events
Handover attempt
Handover success
Handover failure
iDEN Scanner
RX level
SQE
Noise + interference level
Scanning configuration
Defines scanning settings.