Sei sulla pagina 1di 4

Standard Accessories Install software and driver

Leaper-48 main unit x1, USB cable x1, DC 12V/2A adaptor x1, 1. Set Font Size to [small fonts] (96 dpi) to have the optimal display.
Operation software CD-ROM x1, Quick User Guide x1 1.1 Click the right button on the desktop. -> Select the [Properties] in the
bottom of the function menu.
1.2 Select [Settings] and then click the [Advanced] to set Font Size.
2. Install the software before connecting the Leaper-48 to the PC.
2.1 Insert the software CD into your CD-ROM drive. Auto Run start-up
installation. Follow the instructions to complete installation.
2.2 If Auto Run doesn't work, click [Setup.exe] in the CD directory to install.
3. Install the driver of Leaper-48 hardware.
3.1 Make sure the Leaper-48 power is [OFF]. Connect the power adaptor to
the Leaper-48. Plug in and then turn on the power. The green led on the
Main unit Adaptor USB cable adaptor and power led on the programmer panel will be lit on.
3.2 Link the USB cable to PC USB port and programmer USB port.
Introduction 3.3 After assembling the USB cable and the power adaptor, Windows will
auto start-up [Found New Hardware Wizard].
Unit top view
3.4 Install Hardware Device Driver
-> Search for a suitable driver for my device(recommended)
Unit back view 3.5 Locate driver files Optional search locations
-> CD-ROM driver
Power switch USB port (B type)
Power led 3.6 Driver Files Search Result
48Pin Textool -> Windows found a driver for this device....\driver\usbwriter.inf
Action led 3.7 Completing the Found New Hardware Wizard

IC package
diagram
Textool handle DC 12V input socket

Attention
1. It is preferred to use an internal USB port of your PC. External USB
ports are not recommended because of shared bandwidth and
possible compatibility issues of other USB devices.
2. When you use special socket adapters (PLCC, TSOP, SOP...), Please [3.3] [3.4] [3.5]
pull the textool up to 80 . Put the special socket adapter in the
textool and then pull the handle down to fix the socket adapter.
LEAP Electronic Co., Ltd.
Tel : + 886-2-2999 1860
Fax : + 886-2-2999 9873
http ://www.leap.com.tw
Email: service@leap.com.tw

[3.6] [3.7]

* Above installation is described in Windows 2000 *


Parameters Options

1.Memory device split function Device DC/AC parameter settings Device settings 1.Programmer information Programmer self-test
2.High-low voltage verify *only enabled when programmer *only enabled when programmer *only enabled when programmer
3.Pre-check on device is turned on and connected to is turned on and connected to is turned on and connected to
( i.e. pin scan, IC identify... ) the PC the PC the PC
2. Sound settings *Remove any device from the
ZIF socket, if present.
Programming source
Load from PC
Select IC number Verify source IC
IC type Read from Save file Exit program
source IC Edit file
Save file

Source filename

IC manufacturer, type
Load file number and package

Device verify
Check SUM Device pin
check Signal light

Re-scan
Programming status
Process option
Ignore signal
Counter
Clear counter Cancel
Run
Progress Instruction
Stop
percentage
Blank Protect /
Erase Program Verify Auto loop
check security
Program process & options
Source file editing Project
Auto Run:
IC number, Once: Single program Protect lock:
8bits HEX display 16bits HEX display Buffer & file information Description manufacturer Multi: Loop program Undeletable
of Project & package NO: Manual program

Address of data
Click and enter
new address.

HEX code Display


Click to enter
hexadecimal data.
Select project Create new project
Double click to run the project.
Create new project with present settings.
Execute
ASCII code Display Single click to select the project. Delete Project
Only reserve for 10 records. Or the project
Click right button to display properties project
Click to enter text. of the project. Double click blank
keeper will delete the un-protect and
former file (on the top row).
row to create a new project.

Exit edit window Hot Key


Confirm changes

Cancel changes

Set data block


range by
load file size
Get data block
checksum Data block - Set data block range
*When a Microchip Move/Copy/Swap by maximum size of
Data block - Fill buffer
PIC device is selected,
IC checksum will be Set data block
shown directly. range by
selected IC size Click [Space] bar in the main operation screen
to pop Hot Key menu.
How to create a project How to program an IC
Step 1 Select IC number Step 1 Execute Project
Step 1 Create a Project
1.Click [Type] icon.
1.Click [Project] icon. 1.Click [Project] icon.
2.Select IC manufacturer.
2.Click [Create] button 2.Dubble click to run project
3.Select IC number.
to start up the project or click right button to check
editing window./
4.Click [OK] Button.
the properties of the project.
Double click blank
column to create a Double click blank
new project. column to create
3.Enter project Step 2 Get source data a new project.
description.
4.Select [Auto loop] Mode 1: Load from file
parameter: Once/ 1.Click [Load] icon.
Batch/Manual. 2.Click [Browse] to load file.
5.Select [Project Protect] 3.Set file format.
to protect project. 4.Click [Load] button to read data.
6.Click [OK] to save the
project or click Mode 2: Read from source IC
[Cancel] to discard 1.Place source IC.
any changes. 2.Click [Read] icon.
>Start to read and verify IC.
3.Check status and checksum
Step 2 Program IC
Method1: One time auto-program
Step 3 Program IC 1.Place target IC.
>Process IC with project options.
2.Check process status.
IC number,
Description manufacturer Auto Run:
of Project & package Single program Place target IC

Process option
Mode 1:Program single IC Method 2: Loop auto-program
1.Select process options. 1.Place target IC.
2.Place target IC. >Process IC with project options.
3.Click [Run] icon. 2.Check process status.
>Process IC with selected options. 3.Repeat above steps for the next IC.
4.Check process status. Run 4.Click [Cancel] botton to stop programming.

Mode 2: Program batch of ICs


1.Select process option.
2.Place target IC. Click to ignore
3.Click [Auto Loop] icon. the IC check
>Process IC with selected options. and process
4.Check process status. Auto Loop the next IC
>Waiting for placement of the next target IC.
5.Repeat above steps for the next IC. Click to stop
6.Click [Cancel] icon on Scan IC Window to stop process. the batch-
Place Target IC Replace target IC Check IC pins program
Project created Auto Run: and location

date and time Loop program Click to ignore


the IC check Method 3: Manual program
and process 1.Place target IC
Programming Process Protect lock: the next IC 2.Click [Run] icon.
E: Erase IC, C: Blank check, >Process IC with project options.
P: Program IC, V: Verify IC,
Undeletable Run
Click to stop 3.Check process status.
S: Protect/Security
the batch
Place target IC Replace target IC Check IC location programming
and pin status

Potrebbero piacerti anche