Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
“ MIP551 / MIP552 ”
IPD for LED Lighting
1. Concept
2. Feature/Schedule/Circuit Design Tools
3. Operational Description
4. Product Specification(Main Specification/PKG)
5. Example of Application Circuit
4.23.2007
Matsushita Electric Industrial Co., Ltd.
Semiconductor Company
Discrete Business Unit
Concept
Line filter
○ Possible to drive LED
Dimmer
without input aluminum electrolytic capacitor -
signal
IPD
調光信号 IPD
■ Feature
★ Breakdown voltage of internal power MOSFET :≧ 700VDC
★ Output frequency(FOSC):44kHz(typ.)
★ Protective function
・Over current limit protection(ILIMIT)・MIP551:0.5A(typ.)
・MIP552:1.0A(typ.)
・Over temperature protection(OTP):140℃ (typ.)
★ ※Maximum output power:(MIP551)10W (MIP552)30W
※Using input aluminum electrolytic capacitor
★ PKG :(MIP551)DIP7-A1 (MIP552)TO220IPD7-A2
■ Schedule
★ MIP551 : MP 2007/1
★ MIP552 : MP 2007/5
※This is MP condition schedule to be possible to manufacture.
ZNR IFRD
L2
C1
VDS
VIN Drain
L
VDD INPUT
C5 C6
R4 VDD
Before switching After switching R1
C2 MIP55x
(IPD)
VDD(ON)(≒5.8V) F1
C4 VR1 EX
VUV(≒5.1V) SOURCE
good R2 C3
no good
ts
〔Example of LED lighting〕
t
VIN DRAIN
VDS VDD
REGULATOR
ID
IDpeak
VDD UNDER THERMAL SHUTDOWN
VOLTAGE
LINE SENSE
ID UV/OV
Ib L(Line-sense) CL
ENABLE
0
LOGIC
IDpeak OSCILLATOR
GATE DRIVER
MAX DUTY
IFRD
CLOCK
Ib S Q
0 LEADING EDGE
R BLANKING
IDpeak
ILED Io
EX
PEAK CURRENT
ADJUST CURRENT LIMIT
Ib
COMPARATOR
0
■ Constant current drive, which LED peak current is equal to IPD Drain peak current.
Operational Description
(Function ①:Dimming)
LED
IDpeak
D1
ILED
FRD1 L1
R3
ILIMIT
ZNR
L2
C1
VD SLPIL
VIN DrainS
IEX1
INPUT L Hysteresis
C5 C6
R4 VDD (50[mV](typ.))
R1 MIP55x ID IEX2
VEXC2 (IPD)
F1
C4 VR1 EX
SOURCE
R2 C3 0 1 2 3
VEX[V]
〔IDpeak vs VEX〕
ILED
ILED average ILED
ILED
L EX-pin voltage H
Operational Description
(Function ②:Over current protection for LED device with respect to input voltage)
ton ton
(When DRAIN peak current detection level is not switched) (When DRAIN peak current detection level is switched)
〔Increase in DRAIN peak current caused by the delay time and high & low input voltage
(EX pin voltage is 0V)〕
Operational Description
(Function ③: Defining input voltage detection range to drive)
Non-switching
VL (L-pin vs
〔IDpeak voltage)
VL〕 [V]
Non-switching
C1:Big capacitance
C1:Small capacitance
Product Specification(Main Specification)
Item Symbol Min. Typ. Max. Unit
Output Frequency fosc 35.2 44 52.8 kHz
* Skip mode Output Frequency fskip 0.4 × fosc 0.5 × fosc 0.625× fosc kHz
Maximum Duty Cycle MAXDC 46 52 58 %
VDD Voltage VDD(ON) 5.3 5.8 6.4 V
UV Lockout Threshold Voltage VUV 4.6 5.1 5.7 V
Supply Current under Non-Switching IDD(OFF) 0.3 0.6 0.85 mA
CONTROL
FUNCTIONS Supply Current under Switching IDD(ON) 0.4 0.8 1.2 mA
MIP551 0.45 0.5 0.55 A
Peak Current Limit ILIMIT
MIP552 0.9 1.0 1.1 A
Input Voltage offset ILIMIT ILIMTL 0.88×ILIMIT 0.93×ILIMIT 0.98×ILIMIT A
MIP551 0.174 0.2 0.226
* ILIMIT EX2.0 IEX2 A
MIP552 0.348 0.4 0.452
* ILIMIT dimmer Reduction Slope SLPIL -30 %/V
* Leading Edge Blanking Delay ton(BLK) 100 150 200 ns
CIRCUIT
* Peak Current Limit Delay td(OCL) 100 150 200 ns
PROTECTIONS
* Thermal Shutdown Junction Temperature TOTPJ 125 140 150 ℃
MIP551 12 13.6
ON-State Resistance RDS(ON) Ω
MIP552 6 6.8
OFF-State Drain Leakage Current IDSS 5.0 20 uA
OUTPUT Drain Breakdown Voltage VDSS 700 V
MIP551 150
Rise Time tr ns
MIP552 200
Fall Time tf 50 ns
VIN Supply Voltage VIN(MIN) 45 V
SUPPLY
Drain Supply Voltage VD(MIN) 45 V
*: The above characteristics are reference values determined for IC design, but not guaranteed values for shipping inspection.
If problems were to occur, counter measures will be sincerely discussed.
Product Specification(PKG)
■ PKG
○MIP551 ○MIP552
・DRAIN peak current = 0.5A(typ.) ・DRAIN peak current = 1.0A(typ.)
⇒ LED average current ≦ 0.35A ⇒ LED average current ≦ 0.70A