Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
page CONTENTS
BV7.3FLIP 1 General precautions
7.3" Flip Down Widescreen TFT Monitor
1 Safety precautions
BV7.3IRF
7.3" Flip Down Widescreen TFT Monitor 2 Installation precautions
with Built-In Infrared Audio Transmitter
2 Operating precautions
BV8FL
8" Flip Down TFT Monitor 3 Features
7 Remote control:
BV7IRF • BV8FL • BV8IRF • BV8WFLIP
8 System wiring
9 Monitor installation
Congratulations on your purchase
10 Releasing and opening the monitor
of a Video Monitor.
11 Powering up the monitor
It has been designed, engineered 11 Turning on the dome lights
and manufactured to bring you the
highest level of performance and 12 Infrared audio transmission
BV7IRF • BV8IRF
quality, and will afford you years of
viewing pleasure. 12 Remote control battery replacement
13 Troubleshooting
Thank you for making your
choice for car video entertainment! 14 Specifications
• Do not operate this equipment while • if there is smoke or any peculiar odor
driving – safe driving should always present during useor if there is damage
be your highest priority. to any of the component enclosures,
immediately unplug the power cord
• This product should not be installed and send the monitor to your local
in a location which allows the monitor dealer or service center as soon as
screen to be visible to the driver of the possible .
vehicle. In some states and countries,
the viewing of images on a screeen
inside a vehicle is illegal, even by SHOCK HAZARD! Do not open the case
people other than the driver. Be sure of this product. There are dangerous
voltages present within the unit. There are
that the installation and operation of no user-serviceable parts within the unit.
this system is in compliance with local
rules and regulations.
1 2 3 4 5
5 UP/DOWN BUTTONS
3 A/V SOURCE SELECTOR These buttons are used to increase
Use this button to switch between or decrease parameters in the on-
A/V Source 1 and A/V Source 2. screen display menu system.
POWER
2
A/V SOURCE
3
MENU
BV8FL
5 UP/DOWN BUTTONS
3 A/V SOURCE SELECTOR These buttons are used to increase
Use this button to switch between or decrease parameters in the on-
A/V Source 1 and A/V Source 2. screen display menu system.
POWER AV1/AV2
1 1 2
2 3
MENU 3
4
4
1 POWER 1 POWER
Press to turn unit ON or OFF. Press to turn unit ON or OFF.
3 MENU
3 CONTRAST This button enables the on-screen
Increase or decrease the monitor display menu system. Once enabled,
contrast with the (+) and (-) buttons. this button is used as an ENTER button.
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
VIDEO SOURCE 1
(DVD player, video game, etc.)
VIDEO INPUT 1
VIDEO SOURCE 2
(DVD player, video game, etc.)
VIDEO INPUT 2
FUSE
RED
to +12 VDC Battery
POWER BLACK
to Chassis Ground
RED
to +12 VDC Battery
BLACK
DOME LIGHTS to Chassis Ground
BLUE
Car dome lamp (+)
WHITE
Car dome lamp (-)
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
YELLOW VIDEO SOURCE 1
VIDEO (DVD player, video
OUTPUT game, etc.)
RED L
AUDIO OUTPUTS
WHITE
R
FUSE
RED
to +12 VDC Battery
POWER BLACK
to Chassis Ground
RED
to +12 VDC Battery
BLACK
DOME LIGHTS to Chassis Ground
BLUE
Car dome lamp (+)
WHITE
Car dome lamp (-)
CAUTION: Make sure the If you have any doubts about this type of installation, please consult
screws are NOT long enough your local mobile electronics retailer. Making holes in the roof of
to go through the roof! your vehicle will cause damage which is expensive to repair.
INSTALLATION TIP
Make a MOUNTING BRACKET out of wood. This bracket mounts under the headliner,
and provides a mounting surface to which the housing of the flip-down monitor can
be attached.
To lower the monitor further, continue pulling down and the internal mechanism
will permit further movement and will hold the monitor in the position in which you
leave it.
To avoid accidental damage, we suggest you always close the monitor assembly
when it is not in use. To do so, rotate the monitor back to a 0º left-to-right position,
and push it up into the monitor base until you hear a “click.” Test that it is secured
by gently pulling down on monitor frame.
If you know a video input signal is present but the monitor displays "NO SIGNAL,"
be sure to try pressing the AV SELECT button to see if your input source is connected
to the other AV input.
To adjust the monitor image, press MENU to access the various adjustment controls
such as BRIGHTNESS and CONTRAST. Use the +/- buttons to adjust each parameter
until you are satisfied with the picture quality.
The dome lights turn on when you open a door. To turn on or off the dome lights
manually, simply press the round button near the right dome light.
To turn the dome lights on or off manually, simply press the round button on the
side you wish the light to turn on.
The infrared signal is emitted from the large dark lens on the front of the monitor
console. Best sound will be obtained if you sit directly in front of the monitor within
about six feet. If you choose to sit to one side of the monitor, you can expect good
reception within 35º to the right or left of the monitor.
35º
35º
Insert a new battery and push the drawer back fully into the remote.
Battery
Release button
If you experience operation or performance problems with this product, compare your
installation with the electrical wiring diagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
A/V SYSTEM
Screen size 7.3" 8" 8"
Screen format 16:9 4:3 16:9
Video Compatability NTSC NTSC/PAL Auto NTSC/PAL auto
LCD panel type Active Matrix TFT Active Matrix TFT Active Matrix TFT
Resolution, pixels 1152 x 234 1152 x 234 1152 x 234
Brightness 400 NITS 400 NITS 400 NITS
A/V Inputs Video 2EA Video 2EA Video 2EA
GENERAL
Power requirements 12V DC 12V DC 12V DC
Power consumption 9W 6W 6W
Dimensions (L x W x H) 9.8" x 9.5" x 1.6" 10.5" x 8.9" x 1.9" 9.8" x 9.5" x 1.6"
A/V SYSTEM
Screen size 7.3" 8"
Screen format 16:9 16:9
Video Compatability NTSC NTSC/PAL Auto
LCD panel type Active Matrix TFT Active Matrix TFT
Resolution, pixels 1152 x 234 1152 x 234
Brightness 400 NITS 400 NITS
A/V Inputs Video 2EA Video 2EA
INFRARED AUDIO
Power requirements 12V DC 12V DC
Power consumption 3W 3W
Transmitter freq. (R/L) 2.8MHz/2.3MHz 2.8MHz/2.3MHz
GENERAL
Power requirements 12V DC 12V DC
Power consumption 9W 9W
Dimensions (L x W x H) 9.8" x 9.5" x 1.6" 9.8" x 9.5" x 1.6"