Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
TABLE OF CONTENTS
Important Instructions:
Students must keep their working table clean after completing their experiment, drop
the tissue/filter papers in dust bins marked as biodegradable wastes.
Any broken glassware must be reported to lab attender.
After entering the experimental data in the observation note, Students should get
signature from the faculty, take the picture/scan of the evaluated pages and upload it in
the course page within 2-3 days from the date of experiment.
Marks distribution for each experiment: 4 M (expt. data) + 6 M (result) = 10 M
(Weightage = 6 M).
1
Expt. No.: Date:
Water Purification Hardness Estimation by EDTA method and its
Experiment
Removal using Ion-exchange Resin
Hardness of water is due to the presence of dissolved calcium and
magnesium salts in water. EDTA forms stable complex with hardness
Problem definition
causing salts and is used in the removal of scale and sludge forming
impurities in industrial boilers.
EBT indicator-Metal ion complex is weaker compared to EDTA-metal
Methodology ion complex. The end point is the color change from wine red (EBT-
Metal ion complex) to steel blue (free EBT indicator).
Estimation of Calcium hardness (in ppm) in the given unknown
Solution
sample. Understanding the water softening using ion-exchange resins.
Students will learn to
Student learning a) perform complexometric titration
outcomes b) understand the efficiency of ion-exchange resins using in water
purifiers
Principle:
Ehtylenediaminetetraacetic acid (EDTA) forms complexes with a large number of cations
including Ca2+ and Mg2+ depending upon pH of solution. Hence, it is possible to determine
the total hardness of water using EDTA solution. EDTA in the form of its sodium salt
(H2Y2-) is commonly used in complexometric titration for estimation of metal ion because
pure EDTA (H4Y) is sparingly soluble in water. EDTA has six binding sites (the four
carboxylate groups and the two amino groups) providing six pairs of electrons. The resulting
metal-ligand complex, in which EDTA forms a cage-like structure around the metal ion, is
very stable at specific pH. All metal-EDTA complexes have a 1:1 stoichiometry. The H2Y2-
form complexes with metal ions as follows.
M + H2Y2- → MY2- + 2H+ ----------- (1)
Where, M is Ca2+ and Mg2+ present in water. Reaction (1) can be carried out quantitatively
at pH 10 using Eriochrome Black T (EBT) as indicator. EBT forms a wine-red complex with
M2+ ions which is relatively less stable than the M2+-EDTA complex. On titration, EDTA
first reacts with free M2+ ions and then with the metal-EBT indicator complex. The latter
gives a colour change from wine-red to steel blue at the equivalence point.
Removal of hardness using ion exchange resins (IER): Ion exchange is a reversible
process. When hard water is passed through cation ion-exchange resins packed in a narrow
column, Ca2+ and Mg+ cations in hard water are exchanged with Na+ or H+ ions in the
2
resins. The exhausted resins are regenerated by passing 10% dil. HCl through the column. A
typical example of application is preparation of high-purity water for power engineering,
electronic and nuclear industries and in household water purifiers.
Requirements
Reagents and solutions: Standard hard water (1mg/mL of CaCO3 equivalents), 0.01 N
EDTA solution, EBT indicator, hard water sample, NH3-NH4Cl buffer solution and ion
exchange resin.
Apparatus: Burette, pipette, conical flask, standard flask burette stand and IER column.
Procedure
Titration-I: Standardization of EDTA
Pipette out 20 mL of the standard hard water containing 1mg/mL of CaCO3 (1000 ppm) into
a clean conical flask. Add one test tube full of ammonia buffer (NH4OH – NH4Cl) solution
to maintain the pH around 10. Add three drops of Eriochrome Black – T (EBT) indicator
and titrate it against the given EDTA solution taken in the burette. The end point is change
of colour from wine red to steel blue. Repeat the titration for concordant titer values. Let
‘V1’ be the volume of EDTA consumed.
3
Calculation:
20 mL of given hard water consumes V1 mL of EDTA
20 mg of CaCO3 requires V1 mL of EDTA for complexation
1 mL of EDTA requires = 20/V1 mg CaCO3 for complexation
S. Volume of sample hard water (mL) Burette reading (mL) Volume of EDTA
No. Initial Final (V2, mL)
1
2
3
Concordant titer value
Calculation:
From Titration 1, we have the following relation:
1 mL of EDTA requires = 20/V1 mg CaCO3 for complexation
From Titration 2,
20 mL of sample hard water consumes = V2 mL of EDTA.
= V2 x 20/V1 mg of CaCO3 eq.
1000 mL of hard water sample consumes = V2 x 20/V1×1000/20
= V2/V1×1000 ppm
Total hardness of the water sample = “X” ppm
4
Calculation:
From Titration 1, we have the following relation:
1 mL of EDTA requires = 20/V1 mg CaCO3 for complexation
From this relation, it can be seen that
20 mL of water sample after softening through the column consumes = V3 mL of EDTA.
= V3 x 20/V1 mg of CaCO3 eq.
1000 mL of water sample after softening through the column consumes =
= V3 x 20/V1×1000/20
= V3/V1×1000 ppm
Residual hardness of the water sample = “Y” ppm
S. Volume of sample hard water (mL) Burette reading (mL) Volume of EDTA
No. Initial Final (V2, mL)
1
2
3
Concordant titer value
Result:
1. Total hardness of the water sample=“X” ppm
2. Residual hardness in the water sample=“Y” ppm
3. Hardness removed through the column =X – Y ppm
Evaluation of Result:
Sample number Experimental Actual Value Percentage of Marks awarded
value error
5
Water Quality Monitoring: Total Dissolved Oxygen Assessment in
Different Water Samples by Winkler’s Method
2. What is Winkler Method? The Winkler Method is a technique used to measure dissolved
oxygen in freshwater systems. DO is used as an indicator of the water body’s health, where
higher DO concentrations are correlated with high productivity and little pollution. This test
is performed on-site, as delays between sample collections and testing may result in an
alteration in oxygen content.
3. How does the Winkler Method Work? Winkler Method uses titration to determine
dissolved oxygen in the water sample. A sample bottle is filled completely with water (no air
is left to skew the results). DO in the sample is then "fixed" by adding a series of reagents
that form an acid compound that is then titrated with a neutralizing compound that results in a
colour change. The point of colour change is called the "endpoint," which coincides with the
dissolved oxygen concentration in the sample. DO analysis is best done in the field, as the
sample will be less altered by atmospheric equilibration.
4. Applications:
Dissolved oxygen analysis can be used to determine the health or cleanliness of a lake or
stream, amount and type of biomass a freshwater, the amount of DO that a system can
support and the amount of decomposition occurring in the lake or stream.
6
Expt. No.: Date:
Water Quality Monitoring: Total Dissolved Oxygen Assessment in
Experiment
Different Water Samples by Winkler’s Method
Dissolved oxygen (DO) is essential to living organisms in water but
Problem definition
harmful if present in boiler feed water leading to boiler corrosion.
Methodology Winkler’s titration method is used to assess DO in water.
Solution Estimation of total dissolved oxygen in different water samples.
Students will learn to
Student learning
a) perform Winkler’s titration method
outcomes
b) assess the total dissolved oxygen in different water samples
The liberated iodine (I2) is titrated against standard sodium thiosulphate (Na2S2O3) solution
using starch as indicator.
Requirements:
Reagents and solutions: Standard buffer of pH 7, standard potassium dichromate (0.01 N), sodium
thiosulphate solution, 10% KI solution, alkali KI solution (KI + KOH in water), conc. H2SO4,
manganese sulphate, starch solution as indicator.
7
Procedure:
Titration 1: Standardization of Sodium Thiosulphate
Rinse and fill the burette with given sodium thiosulphate solution (Bottle B). Pipette out 20 mL of
0.01N K2Cr2O7 solution (Bottle A) into a clean conical flask. To this, add 5 mL H2SO4 (1/2 T.T.), 10
mL of 10% KI, and titrate against sodium thiosulphate solution. When the solution becomes straw
yellow colour, add starch indicator and continue the titration. End point is the disappearance of bluish
brown colour. Repeat the titration to get concordant value.
Concordant value
Calculations:
8
Titration – II: Estimation of Dissolved Oxygen
Burette reading (mL) Volume of sodium
Volume of water sample
S. No. thiosulphate
(mL) Initial Final
(mL)
1
Concordant value
Calculation:
Volume of sodium thiosulphate V2 = ……… mL (From Titration – 2)
Strength of sodium thiosulphate N2 = ………… N (From Titration – 1 calculation)
Volume of water sample taken V1= 100 mL
Strength of given water sample N1 = ?
V1N1 = V2N2
N1 = V2 X N2/100
= ……………. N
Amount of dissolved oxygen (ppm) = normality × equivalent weight of O2 × 1000 mg/L of the given
water sample.
= ……………….N × 8 × 1000 mg/L
= ------------------ ppm.
Result: Amount of dissolved oxygen in the given water sample = ……… ppm.
Evaluation of Result:
Sample number Experimental Actual Value Percentage of Marks
value error awarded
9
Construction and working of an electrochemical cell
An Electrochemical Cell
The oxidation reaction in the zinc rod releases 2e- and are taken by the Copper ion in the
CuSO4 solution. If these two half reactions can be separated, then the electrons can be
made to move through a wire. In this manner, we can produce electrical energy from
chemical energy. The salt bridge is a concentrated solution of inert electrolytes. It is required
for completing the circuit. It allows the movement of ions from one solution to the other.
10
Expt. No.: Date:
11
Procedure:
Calibrate the digital potentiometer with the help of the wires to display 1.018 V. The metal electrode
is sensitized by dipping in a small quantity of 1:1 nitric acid containing a small quantity of sodium
nitrite until effervescence occurs. Then the electrode is washed well with distilled water. 50 mL of the
given concentration of the electrolyte solution is taken in a beaker and its corresponding metal
electrode is introduced. This is connected with the saturated calomel electrode (half-cell) by means of
a salt bridge. The metal electrode is connected to the positive terminal and the calomel electrode is
connected to the negative terminal of the potentiometer. EMF of the cell (Ecell) is measured and noted
in Table 1. Standard electrode potential [E°M/M2+] is computed using Nernst equation (Eq. 1).
Solution Temperature (T) = °C; Potential of SCE = 0.244 + 0.0007 (25 °C)
E°M/M+ = EM/M+ – 0.0595 Iog [γc x C] - - - - - - (1)
n
where, E° is standard electrode potential of metal electrode; aMn+ is activity of metal ions in solution
(aMn+ = γc[C]); γc is activity coefficient (Table 2) and C is concentration of electrolyte solution.
12
Construction of Daniel cell and measurement of its voltage with three different concentrations
of Cu/Zn solutions:
In the Daniel cell, copper and zinc electrodes are
immersed in the equimolar solution of CuSO4 and ZnSO4
respectively.
At the anode, zinc is oxidized as per the following half-
reaction: Zn(s) → Zn2+(aq) + 2e−
At the cathode, copper is reduced as per the following
reaction: Cu2+(aq) + 2e− → Cu(s)
The overall reaction is: Zn(s) + Cu2+(aq) → Zn2+(aq) + Cu(s)
Construct Daniel cell using the following concentrations
of Copper and Zinc solutions and record the voltage of
the cells in Table 3.
Table 3: EMF of Daniel Cell observed from three different conc. of Zn and Cu solutions
Concentration Concentration EMF observed
Metal Metal
(N) (N) (Ecell / V)
0.01 N 0.01 N
Zn/Zn2+ 0.02 N Cu/Cu2+ 0.02 N
0.05 N 0.05 N
Average
Results:
(a). Standard electrode potential of Copper (Eo) = ____________ vs. SCE
(b). Standard electrode potential of Zinc (Eo) = ____________ vs. SCE
(c). EMF of the constructed Daniel cell = __________________
Evaluation of result:
Experimental Percentage
Sample No. Actual Value Marks awarded
Value of error
a) Eo Cu /Cu2+
b) Eo Zn/Zn2+
13
Quantitative colorimetric determination of Ni2+ metal ions using
conventional and smart phone digital-imaging methods
2. Nickel Toxicity: Compared with other transition metals, Nickel is a moderately toxic
element. However, it is known that inhalation of nickel and its compounds can lead to serious
problems, including cancer in the respiratory system. Moreover, Nickel can cause a skin
disorder known as nickel-eczema (10.1016/j.kijoms.2016.08.003).
3. Nickel in Industries: A thin layer of nickel onto a metal object can be decorative, provide
corrosion resistance, wear resistance, or used to build up worn or undersized parts for salvage
purposes. Nickel alloys are used extensively because of their corrosion resistance, high
temperature strength and special magnetic and thermal expansion properties.
The major alloy types that are used are:
Iron-Nickel-Chromium alloys
Stainless Steels
Copper-Nickel alloys and Nickel-Copper alloys
Nickel-Chromium Alloys
Nickel-Chromium-Iron alloys
Low Expansion Alloys
Magnetic Alloys (http://www.nickel-alloys.net/nickelalloys.html)
14
Expt. No.: Date:
Quantitative colorimetric determination of Ni2+ metal ions using
Experiment
conventional and smart phone digital-imaging methods
Corrosion protection in steel depends on the amount of Ni (acts as
Problem definition passivating metal) in its composition. Hence, it is important to analyze the
amount of Ni in steel for its use in industry.
Ni-DMG forms a stable colored complex. With increasing concentration
of Ni in solution, its color intensity also increases. In turn, the color
Methodology
intensity is a function of color coordinates (Red, Blue and Green, RGB) in
the image taken using mobile phone camera.
Estimation of Ni concentration in the unknown sample from the
Solution
calibration graph plotted based on different known Ni concentrations.
Student learning Students will learn to perform colorimetric method, perform RGB
outcomes response analysis and analyze Ni composition in different grades of steel
(i). Principle:
(a). Colorimetric method:
Photo-sensitive measurements are expressed in terms of absorbance, (A) as given in Eq. (1).
Further, the linear relationship between absorbance (A) and concentration of the analyte
ɛcl = A = log(I0/I) … (1)
Where, I0 is the incident light power, I the transmitted light power, ɛ = molar absorptivity, c =
concentration of analyte and l = thickness of the solution.
15
Scheme - 1
Requirements:
Reagents and solutions: NiSO4 (100 ppm), NaOH (1 N) solution, DMG, K3[Fe(CN)6]
Instrument: Colorimetry and smartphone
(iii). Procedure:
(a). Colorimetry method: Take 6 standard 50 mL volumetric flasks (to prepare 5 known and
1 unknown solution). Fill the burette with Ni stock solution (100 ppm). Add 1, 2, 3, 4 and 5
mL of the Ni solution in burette to the std. flasks to get 2, 4, 6, 8 and 10 ppm of steel
containing nickel(II) solutions. The unknown sample will be furnished in another 50 ml
volumetric flask. Further, add 0.5 mL of DMG solution followed by 0.5 mL of K3[Fe(CN)6]
solution using a burette to all the 5 std. flasks. All the flasks are shaken well once and waited
for 5 minutes. After that, make up the 50 mL mark in std. flask with 1N NaOH solution.
Allow the flasks at least 10 minutes for the complete complex formation. Absorbance of the
formed brown-red solution is measured at 440 nm against NaOH solution (blank). Record
these absorbance readings in Table 1.
16
Draw a calibration graph taking concentration of Ni2+ (in ppm) as X-axis and absorbance
readings as Y-axis. A straight line that passes through the origin (see Fig. 2) is an indication
that the measured data obeys Beer’s Law. From the calibration plot, measure the
concentration of nickel in the given unknown sample.
(b). Digital imaging method: The prepared standard solutions are lined up along with
unknown concentration sample and blank. Using a white paper as background, take a
photograph of the samples by holding the camera around 50 cm away. Calibration curve will
be constructed through the RGB values of analytical response with different conc. of Ni2+
ions using “RGB Tool” APP.RGB In the plotted
Method RGBgraph,
Flow RGB response
Method
Chart varies linearly vs the
Flow Chart
analyte concentration. In order to get precise analysis, follow the steps given below:
Transfer prepared standard
Transfer solution
prepared and unknown
standard solution
solution and unknown solution
into different into
colorimetric
differenttest tubes
colorimetric test tubes
Go to gallery,Go
opento the image
gallery, stored
open the in app stored
image and in app and
extract RGB values
extractfor each
RGB image/conc.
values for each image/conc.
2.
3.
4.
5.
Unknown
*If your solution looks Red or blue or green, then the corresponding ratio can be ignored and select
RGB data which is linear with concentration of analyte for plotting calibration graph (Y-axis)
17
Find the unknown conc.
Find the Using the
unknown conc. Using the
calibration curve
calibration curve
Result:
(i). Concentration of Ni in steel sample (using colorimetry) = _________ ppm (mg/L)
(ii). Concentration of Ni in steel sample (using digital imaging) = _________ ppm (mg/L)
Evaluation of result:
Sample Experimental Actual Percentage Least Marks awarded
number value (ppm) value of error error % value
(ppm)
Colorimetry method
Digital-imaging method
18
Quantitative colorimetric determination of Fe2+ metal ions using conventional and
smart phone digital-imaging methods
1. Source of Iron in drinking water: Iron is a common metallic element found in Earth
crust. Water percolating through soil and rock can dissolve minerals containing iron and hold
them in solution. Occasionally iron pies may also be a source of iron in water. In deep well,
where oxygen content is low, the iron bearing water is clear and colourless. But that water
pumped from motor is exposed to surface oxygen and change into colored solid forms,
initially into white, then yellow and finally to red-brown solid precipitate that settle out of the
water.
2. Iron in drinking water: Iron is one of the many minerals that are essential for human
health. Without iron, people may experience anaemia, fatigue, or an increase in infections.
But how much iron is too much? Drinking water that contains iron can be beneficial to your
health. However, excessive iron in drinking water may have negative effects like poor skin
and metallic taste in water. Because water and iron don’t physically mix well, people may
notice leftover soap residue after showering or bathing. This soap build-up can also cause
skin problems. Iron overload can also lead to hemochromatosis - which can cause damage to
the liver, heart, and pancreas. Excessive iron can leave behind a residue in plumbing lines and
this is yet another reason to consider removing iron from water. There are plenty of health
concerns associated with too much iron intake, which is one of the main reasons people using
well water should schedule annual water testing.
19
Expt. No.: Date:
Quantitative colorimetric determination of Fe2+ metal ions using
Experiment
conventional and smart phone digital-imaging methods
Excess Iron in drinking water cause negative effects like poor skin and
hemochromatosis (damage to liver, heart and pancreas). There are plenty
Problem definition
of other health concerns associated with too much iron intake, and hence
it is important to estimate the amount of iron in waste samples.
Fe and 1,10-phenanthroline forms a stable deep-red colored complex.
With increasing concentration of Fe in solution, its color intensity also
Methodology
increases, which in turn is a function of color coordinates (Red, Blue and
Green, RGB) in the image taken using mobile phone camera.
Estimation of Fe concentration in different water samples can be found
Solution out using colorimetry technique from the calibration graph plotted based
on different known Fe concentrations.
Student learning Students will learn to perform colorimetric method, perform RGB
outcomes response analysis and analyze Fe composition in different grades of steel
(i). Principle:
(a). Colorimetric method:
Photo-sensitive measurements are expressed in terms of absorbance, (A) as given in Eq. (1).
Further, the linear relationship between absorbance (A) and concentration of the analyte
ɛcl = A = log(I0/I) … (1)
Where, I0 is the incident light power, I the transmitted light power, ɛ = molar absorptivity, c =
concentration of analyte and l = thickness of the solution.
20
hydrochloride salt to increase solubility) is added to reduce any Fe3+ to Fe2+ and to maintain it
in that state. The spectrum is plotted to determine the absorption maximum.
(iii). Procedure:
(a). Colorimetry method: Take 6 standard 50 mL volumetric flasks (to prepare 5 known and
1 unknown solution). Fill the burette with Fe stock solution (10 ppm). Add 2.5, 5, 10, 15 and
20 mL of the Fe solution in burette to the std. flasks to get 0.5, 1, 2, 3 and 4 ppm of Fe(II)
solutions. The unknown sample will be furnished in another 50 ml volumetric flask. Further,
add 0.5 mL of hydroxyl ammonium chloride solution followed by 2.5 ml of 1,10-
phenanthroline using a burette. The Fe(II)-phenanthroline complex forms at pH 2 to 9. Add
2.5 mL of sodium acetate buffer to neutralize the acid present and adjust the pH to a value at
which complex forms. After that, make up the 50 mL mark in std. flask with distilled water.
Allow at least 15 minutes before making absorbance measurements so that the color of the
complex can fully develop. Once developed, the color is stable for hours. Obtain the
absorption spectrum of the Fe solutions by measuring the absorbance from about 400 to 600
nm.
Record these absorbance readings in Table 1. Draw a calibration graph taking concentration
of Fe2+ (in ppm) as X-axis and absorbance readings as Y-axis. A straight line that passes
through the origin is an indication that the measured data obeys Beer’s Law. From the
calibration plot, measure the concentration of Iron in the given unknown sample.
21
Digital imaging method: The prepared standard solutions are lined up along with unknown
concentration sample and blank. Using a white paper as background, take a photograph of the
samples by holding the camera around 50 cm away. The calibration curve will be constructed
through the RGB values of analytical response with different concentration of Fe2+ ions using
smartphone app (RGB Tool). In the plotted graph, RGB response varies linearly vs the
analyte concentration. In order to get precise analysis, follow the steps given below:
RGB Method Method
Flow
RGB Chart Flow Chart
Go to gallery,Go
opento the image
gallery, stored
open the in app stored
image and in app and
extract RGB values
extractfor each
RGB image/conc.
values for each image/conc.
2.
3.
4.
5.
Unknown
*If your solution looks Red or blue or green then the corresponding ratio can be ignored and select
RGB data which is linear with concentration of analyte for plotting calibration graph (Y-axis)
Digital-imaging method
23
Polymer Characterization: Determination of Viscosity of Different Natural
Polymer/Synthetic Polymers
2. Concept: Molecular weight of polymer (M) can be derived from intrinsic viscosity data of a
polymer solution. But one pre-requirement to determine the molecular weight of a polymer is the
knowledge of Mark-Houwink (M-H) coefficients. Upon substitution of intrinsic viscosity and these
coefficients in M-H equation, one can find out molecular weight of the polymer. M-H equation =
KMv, where K and are M-H coefficients and = intrinsic viscosity of the polymer solution. In
this experiment, we focus on the determination of intrinsic viscosity of the given polymer solution.
3. Applications: Nowadays, polymers have become essential requirements in our day to day
activities. The end applications of the polymer depend upon its characteristics such as molecular
weight, polydispersity index, thermal stability, crystalline/amorphous nature, stereochemistry, etc.
Among these, molecular weight of the polymer is very important. LDPE (low density polyethylene) is
used as packing materials and carry bags, whereas UHMWPE (ultra-high molecular weight
polyethylene) is used as containers, tubing and other heavy-duty equipments due to its high abrasion
resistance, high impact strength and low coefficient of friction. Most of the bottles for carbonated
drinks, mineral water, edible oil and personal care products are made of poly(ethylene terephthalate),
PET and their intrinsic viscosity values range from 0.7-0.85 dL/g, depending on the length of the
polymer chain (the longer the polymer chains, the more entanglements between the chains and
therefore the higher the viscosity).
Fig. 1: A portion of Ostwald viscometer Fig. 2: A plot of reduced viscosity vs. concentration
showing the upper and lower graduation of a polymer solution, y-intercept corresponding to
marks, 'a' and 'b' respectively. intrinsic viscosity.
24
Expt. No.: Date:
Principle:
When a polymer is mixed with a solvent, the solvent enters into the polymer matrix and swelling of
polymer coils takes place. This expanded polymer coil disintegrates and moves out of polymer matrix
and dissolves in the solvent. The apparent volume occupied by the expanded coil is referred to as the
`hydrodynamic volume’ of the polymer molecule in the solution under flow. Viscosity of a polymer
solution is a direct measure of hydrodynamic volume of the polymer, which in turn, is a measure of its
molecular weight. Viscosity of a polymer is more in a good solvent than in a poor solvent.
Procedure:
Prepare at least 3 different diluted concentrations of PEG (1 to 5%) in water
using 10% PEG stock solution (10 g/100 mL). Initially, rinse the Ostwald
viscometer with a little amount of water. Fill it with 20 mL pure water and use
a rubber filler to suck the water above the upper mark. By keeping the upper
mark of the small reservoir of viscometer parallel to eyes, allow the solvent to
flow down to the lower mark and note down time in seconds. This is known as the E flux time. Repeat
the same experiment for 2 times to get the average Eflux time for water (t0). Apply the same procedure
to determine the flow rate for remaining 2 diluted solutions and note down their flow time in seconds.
Calculate relative viscosity, specific viscosity and reduced viscosity as shown in Table 1. Plot the
graph between polymer concentrations (C g/mL) vs red. The value of intercept at C = 0 will give
intrinsic viscosity of the polymer solution (see Fig. 1).
25
Table 1: Viscosity measurement data
Concentration, Eflux time, t (sec)
S. No. r = ts/t0 sp = r-1 red = sp/c
C (g/mL) t1 t2 ts = t 1 + t2 / 2
1
2
3
20
15
sp/C
10
5
0
0 0.02 0.04 0.06 0.08 0.1
Concentration (C g/mL)
Calculations:
= KMv
Molecular weight of the given polymer (Mv) =
Result:
(a) Eflux time for pure water (t0) = _______sec.
(b) Intrinsic viscosity of the polymer () = ---------
(c) Molecular weight of the given polymer (Mv) = ---------
Evaluation of Result:
Sample number Skill value Mv Calculated Mv Error % Marks awarded
26
Estimation of sulphate in drinking water by conductivity method
Sulphate (SO42-) is found in almost all natural water. Origin of most sulphate compounds is the
oxidation of sulphite ores, presence of shales or the industrial wastes. Ground water moving
through soil and rocks containing sulphate minerals result in higher dissolved sulphate ions than
permissible limit.
27
Expt. No.: Date:
Experiment Estimation of sulphate in drinking water by conductivity method
Problem definition People using water with high levels of sulfate are vulnerable to
dehydration and diarrhea. Kids are more sensitive to sulfate than adults.
Methodology Conductivity of the soluble sulphate solution will change when it is
precipitated by BaCl2. Conductivity will reach minima when all sulphate
ions are precipitated, and from which, the total amount of sulphate ion
present in the water can be determined.
Solution Amount of BaCl2 required to remove the dissolved sulphate can be
estimated.
Student learning Students will learn to
outcomes a) perform conductometric method
b) remove sulphate ion from irrigate water
Principle:
Electrolyte solutions conduct electricity due to the presence of ions in solution. In case of
precipitation titration between BaCl2 and Na2SO4, the conductance decreases slowly due to the
replacement of Cl- ion by SO42- ion upto the equivalence point. After the equivalence point, the
conductance increases rapidly due to the excess addition of BaCl2 which remains in solution as
Ba2+ and Cl-. This makes detection of neutralization point easy from the conductance trend
plotted as a graph. This is the principle used in the estimation of SO42- from contaminated water
sample.
Requirements:
Reagents and solutions: BaCl2 (0.1 N), Na2SO4 (0.02 N), unknown sulphate solution and
distilled water.
Apparatus: Conductivity Bridge, Conductivity cell, Burette, Pipette, Volumetric flasks, Glass
rod, Beaker (100 mL).
Procedure:
Calibration of Conductivity meter: Place a freshly prepared 0.1 N KCl solution (given in
bottle) in a 100 mL beaker. Dip the conductivity cell in this solution and connect to the
Conductivity meter. Press “CAL” button and complete the internal calibration of the instrument.
28
Standardization of BaCl2 (Titration – 1):
Pipette out 20 mL of 0.02 N Na2SO4 solution (from Bottle A) in a 100 mL beaker and add 10 mL
of distilled water to it to make the conductivity cell dip completely in the solution. Addition of
water will not affect the conductivity since the number of ions in the solution remains unaltered.
Dip the conductivity cell into the solution in the beaker and connect to the conductivity meter.
Fill the burette with ~0.1 N BaCl2 solution (from Bottle B). Record the conductivity of the
sulphate solution without adding any BaCl2 from the burette (0th reading). Add 1 mL BaCl2 of
known concentration into the beaker, stir with glass rod and note down the conductance.
Continue the addition of BaCl2 (1 mL each time) and note the conductance after each addition.
Continue the titration beyond the equivalence point for about 5 mL. The conductance will either
decrease slightly or remain constant until complete precipitation of BaSO4, and then starts
increasing on continuing the addition of BaCl2. A graph is now drawn by plotting conductance
vs volume of BaCl2 added. Intersection point from the plot gives the volume of BaCl2 required
for precipitating the sulphate present in the known sample.
Make up the unknown sulphate solution given in a 100 mL standard flask upto the mark using
distilled water resulting in a solution containing 0.96 mg/mL of sulphate ions (Eq. wt. of SO42- =
48.03). Pipette out 20 mL of this solution into a 100 mL beaker and add 10 mL distilled water to
it. Dip the conductivity cell and repeat the above procedure with the unknown sulphate solution
to determine the amount of BaCl2 required for precipitating the unknown sulphate in the sample.
From the two titrations carried out, calculate the amount of sulphate present in the effluent
sample.
29
Table 1: Conductometric Titrations
Titration-1: Standardization of BaCl2 Titration-2: Estimation of sulphate content
Burette: BaCl2 solution (~0.1 N) Burette: std. BaCl2 solution
Beaker: 20 mL of Na2SO4 (0.02 N) + 10 Beaker: 20 mL of unknown sulphate solution +
mL of distilled water 10 mL of distilled water
Conductivity cell, Conductivity meter Conductivity cell, Conductivity meter
Fig 1: Model graphs – 1 and 2 for Conductometric estimation of known and unknown sulphate
sample solutions, respectively.
30
Calculations:
Amount of sulphate present in 1L = Normality of irrigation water sample x Eq. wt. of SO42- (48.03)
Amount of sulphate present in given sample solution = Strength of irrigation water sample x 48.03 x100
1000
=__________ grams in 100 mL
Evaluation of Result:
Sample number Experimental Actual Value Percentage of Marks
value error awarded
31
Iron in carbon steel by potentiometry
1. Importance of the experiment: Steel production is an index of national prosperity and economy,
and is globally used in variety of industrial sectors like shipbuilding, automobiles, construction,
machinery and tools. Carbon steel is one variety in which nearly 96% of iron is alloyed with nearly
2% of carbon and other elements like manganese, chromium, nickel and copper. The composition is
varied for achieving desired strength, ductile and long-term wearing properties. Thus, qualitative
determination of iron in steel is very important.
Change in the concentration of Fe2+ ions during the addition of KMnO4 is monitored by
measuring the solution potential which is the basis for this experiment. From Nernst equation, a
measurable quantity - voltage or potential is related to the concentration of species (Fe 3+/Fe2+) in the
solution.
RT Fe 3
E E0 ln( 2 )
nF Fe
At the end point, a rapid change in the potential would be observed indicative of the complete
conversion of Fe2+ to Fe3+. A plot of observed potential vs volume of KMnO4 consumed or its first
derivative graph (E/V vs average volume of KMnO4) is used to detect the titration end point, which
in turn, is used to qualitatively measure the amount of Fe2+.
32
Expt. No.: Date:
Principle:
Potassium permanganate (KMnO4) oxidizes ferrous ion to ferric ion in the presence of acid as per the
reaction:
5Fe+2 → 5Fe+3 + 5e- .......(1)
MnO4- + 8H+ + 5e- → Mn2+ + 4H2O .......(2)
Overall, 5Fe+2 + MnO4- + 8H+ → 5Fe+3 + Mn2+ + 4H2O
Electrode potential (oxidation potential) in the titration depends upon the concentration of Fe 2+, Fe3+
and H+ ions. To avoid the effect of the change in H+ ion concentration, the titration is usually carried
out in large excess of acid. Oxidation potential of this redox system is given by
RT Fe 3
E E0 ln( 2 )
nF Fe
Connecting the redox electrode (Platinum) with a saturated calomel electrode (SCE) completes the
necessary cell as indicated below:
HgHg2Cl2 (s), Saturated KCl Fe3+, Fe2+Pt
When KMnO4 is added, Fe2+ is oxidized to Fe3+ whose concentration increases with progressive
addition of KMnO4. The observed EMF gradually increases. At the end point, there will be a sharp
increase due to the sudden removal of all Fe2+ ions. Plot-1: EMF measured (E) vs Volume of KMnO4
added and Plot-2: E/V vs Average volume of KMnO4 was drawn. End point of the titration is
measured from the Plot-2 graph.
Requirements:
Reagents and solutions: 100 mL of KMnO4 (0.05 N) solution, 100 mL of steel solution, 2 N H2SO4.
33
Fig. 1: Typical apparatus for potentiometric Fig. 2: Typical Potentiometric titration curves. (a)
titrations. Normal curve and (b) First derivative curve.
Procedure:
Calibration of Potentiometer: Switch on the potentiometer and connect the standard cell terminals
to either channel A (move channel switch to position A) or channel B (move the channel switch to
position B). The meter should read 1.018 V. In case it is not 1.018 V, adjust the std. knob to obtain
reference value.
Estimation of Fe(II) in steel: Transfer the given unknown steel [containing Fe(II)] solution into a
clean 100 mL standard flask and make the solution up to the mark with distilled water and mix well.
Pipette out 20 mL made up steel sample solution into a clean 100 mL beaker and add one test tube of
dil. H2SO4 (2 N). Place Pt electrode in the beaker and connect to the +ve terminal of the
potentiometer. In another beaker, place 50 mL of saturated KCl solution and dip the SCE in the
solution and connect to the -ve terminal of the potentiometer. Place a salt bridge to complete the cell.
Read the EMF of the cell and note down the value. Add 1 mL of KMnO4 solution from the burette to
the beaker containing steel sample solution. Stir the solution carefully and measure the EMF.
Continue the addition of KMnO4 solution and record the EMF for every 1 mL addition as per
procedure till the potential shows a tendency to increase rapidly. After the abrupt change in cell EMF
is observed, continue the titration to take 5 more reading by adding 1 mL burette solution every time.
Plot EMF (ordinate) vs. volume of KMnO4 added (abscissa) to get S-shaped curve which indicate the
volume range of the end point.
To find out the volume of end point more precisely, carry out the 2nd titration in similar way but by
adding 1 mL aliquots of KMnO4 initially and then 0.1 mL aliquots between the two volumes where
the end point is detected. Continue the titration beyond the end point as done above. The exact end
point is determined by differential method i.e. by plotting ΔE/ΔV vs average volume of KMnO4
added. Calculate the normality strength of the Fe(II) in the given solution.
34
OBSERVATION AND CALCULATIONS
Potentiometric Titration-I:
Burette: KMnO4 solution (0.05 N)
Beaker: 20 mL of steel solution containing Fe(II) + 20 mL (one test tube) of dil. H2SO4
Electrodes: Indicator electrode (Pt) to red terminal and SCE to black terminal
35
Potentiometric Titration-II:
Burette: KMnO4 solution (0.05 N)
Beaker: 20 mL of steel solution containing Fe(II) + 20 mL (one test tube) of dil. H2SO4
Electrodes: Indicator electrode (Pt) to red terminal and SCE to black terminal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
36
Calculation:
Amount of Fe present in 1L of sample solution = Normality of steel sample x Atomic weight of Fe (55.85)
Amount of Fe present in given sample solution = Normality of steel sample x 55.85 x 100
1000
=________________grams in 100 mL
Result: The amount of Iron present in given steel sample is found to be =_________ grams.
Evaluation of Result:
Sample number Experimental Actual Value Percentage of Marks awarded
value error
37
Expt. No.: Date:
Introduction:
In this demo, students will be able to understand the real-time monitoring of acid-base
titration using Arduino microcontroller based sensor. Acid-base titration is a common lab
experiment and finds its application is wide variety of problems. A strong acid (HCl) is
titrated against weak base (Na2CO3) and the change in pH is monitored using a pH meter.
When the pH reaches 7, it indicates the end point. Instead of using a conventional
microcontroller based pH meter, we can use an Arduino board to acquire and process the data
obtained from the pH probe. Arduino is an open source electronics board, finding its
application in all the domains of S&T. Arduino board is programmable and can be connected
to laptop or smart phone (using Bluetooth) to get the data.
Experiment:
When acid is titrated with base, there will be change in pH of the resulting solution. The pH
probe will measure the pH and will give the output as voltage. This voltage is then feed into
the Arduino board as analog input and can be stored in the computer.
38
Fig. 1: Pictorial representation of the experimental setup
Course outcome:
After the end of this demo experiment, the students can
1) Learn chemistry behind acid acid-base titration.
2) Measure pH of any solution.
3) Can use and program Arduino board and apply it to measure and control any other
property or devices respectively.
4) Acquire the knowledge of electronics, data acquisition and processing.
5) Understand the technology behind the measurement and instrumentation.
6) Since the Arduino is programmable, the student has flexibility to alter the experiment
and can customize it for different applications.
39